MINOURA LR760 User Manual

indoor bicycle trainer

Applicable Tire Size Capacity:

(ETRTO 42-622)

any 24-inch – 700 x 40c

(Max Tire Outer Diameter = 712mm)

instructions manual

(ver.1.3 2014/2)

Main Features

• The combination of the simple & durable mono-leg design frame and the powerful MagteqsTwin resistance unit

• Uses a pair of super-strong Neodymium magnets for providing extremely wide and controllable resistance range

• Compact round-knob design remote shifter enables to choose your desired power from 13 resistance levels easily

• Thick outer edge ywheel design generates more initial inertia through virtual weight of 2.7 kgs

• New double-thread knob type roller pressure system enables quick & easy setup/release operation

• Quick release type hub clamping mechanism

Please Note

Contact

MINOURA North American Tech Center MINOURA Japan Headquraters

(for U.S. residents ONLY)

Hayward, California, U.S.A. 1197-1 Godo, Anpachi, Gifu 503-2305 Japan
Phone: [phone] (8 am - 5 pm, Mon - Fri, PST) Phone: [phone]
Fax: [phone] Fax: [phone]
Email: [e-mail] Email: [e-mail]
Web: www.minoura.jp

This trainer must be used with a completely smooth (no knobs or raised tread) tire.
Failure to do so will ruin the mag unit, your tire, and void any possible warranty.

If you need help, please contact the shop first where you originally purchased this product
or call the distributors in your country. The distributors list can be found on our web site.
When you cannot get enough service, you can contact us;

(for ALL customers)

MADE IN JAPAN

Important Notes

• For use with a normal 2-wheel bicycle only. Do not use a tandem, recumbent, or other.

• Hub nut type rear wheel axle is not compatible with LR760 in standard.
You need to replace the left side coupling bolt (UF-8S) with optional longer "Left Side Coupling
for Hub Nut Axle (UF-8L)".

• Fits tire size between 24" and 700x40c (ETRTO 42-622). To use 26x1.75" or smaller tire, install
the supplied Small Wheel Adaptor between the Mag unit and the base bracket. 29" tires may
not be used on LR760.

• Some assembly required. Use correct tools (10mm spanner and M5 & M4 hex wrenches).
The kit contains only M5 hex wrench.

• Use the supplied rear quick release skewer for maximum stability. The hub clamping parts
(couplings) ts the supplied quick release skewer only. Minoura is not responsible for any
problem caused from using your own skewer.

• Use on at and level oor or ground for your safety.

Please read carefully before use

• Adjust the roller pressure to the rear tire properly in order to maximize your tire life.

Tire and roller contact will eventually wear both your tire and the trainer roller.
Wipe the tire surface to remove any solid dust away before setting the bike on the trainer in
order to maximize the drive roller life.

• Check and adjust the remote shifter cable tension properly when you cannot set at L or H even

though you turn the shifter lever.

• Touching the spinning wheel and/or any other moving parts while training may cause serious
injury. Keep children and pets away from the trainer when in use.

• It is not possible to convert the remote controllable resistance unit to the non-remote version

one. Removing the remote shifting device means xing the resistance level at the highest
range.

• If you feel any strange noise or smell, stop using LR760 immediately and contact the retailer

where you purchased the trainer.

• To protect the oor or carpet from stain and sweat during workout, we recommend you to put

a sheet or mat under the trainer and bike.

• Any warranty will be void if you use LR760 for other purpose than instructed.
Minorua offers 1-year limited warranty on this product from the date of your purchase for any
problem caused by manufacturer's defect. Natural wear will not be covered.
Any damage or problem caused by transporting process is not covered under warranty. Any
damage from shipping or moving must be made to the shipping company.
Read the enclosed "Minoura Limited Warranty Policy" card for more detail.
For the latest information, refer Minoura web site (http://www.minourausa.com).

- 2 -

How To Install Mag Unit & Roller Adjust Knob

Required Tools: 1 x 5mm Hex Wrench (supplied)
1 x 10mm Spanner (not supplied)

Install the Mag resistance unit and Roller Pressure Adjust
Knob to the frame.

Mag Resistance Unit

First, attach the e Knob, and tighten both brackets together
using the pivot bolt and M6 nut. (Fig. A)

!

Overtightening the pivot bolt will cause the Knob to
become inoperable.
Make sure you unscrew (loosen) the pivot bolt by 1/4

- 1/2 turn once you completely tightened it.
The Mag unit should be lowered slowly towards the
ground by its own weight at this point.
If the pivot bolt is too loose, the Mag unit may drop

suddenly and come down on your hand or ngers.

Make sure to adjust the torque properly to insure
proper operation.

Your bicycle tire should be as close to the center of the
roller as possible. (see Fig. B)
If the tire has been touching the plastic housing, damage
will occur to the Mag unit and your tire.
The base bracket has two sets of thread holes for mounting
the Mag unit. Choose the better holes.
Also it can be micro-adjusted and to do so, loosen the
backside screws and slide the Mag unit in the direction
needed to center the tire properly.
Tighten the screws when you have finished.

M6 Nut

Roller Pressure Knob

Rear Tire

Pivot Bolt

Step-Bar

(Fig. A)

(Fig. B)

How To Use Small Wheel Adaptor

If your tires are 26" or smaller and are less
than 1.75" in width, you will need to use the
supplied Z-shaped Small Wheel Adapter.
Your tire size should be clearly marked on the
tires sidewall.

The direction of the Z-adapter is fixed so
follow the arrow printed on the top and make
sure it's pointing toward the front (toward
your bike).
If the drive roller cannot reach the tire, make
sure the Z-adapter has been installed correctly.

Use the original round head bolts for the
Mount Base, and use the supplied hex head
bolts for the Mag unit. (see Fig. C)

Z-Adaptor

Hex Head Bolt

Round Head Bolt

- 3 -

(Fig. C)