Mindray DPM1 User manual

Intellectual Property Statement

Mindray DS USA, Inc. (hereinafter called Mindray DS) owns the intellectual property rights

to this product and this manual. This manual may refer to information protected by

copyrights or patents and does not convey any license under the copyright and the patent

rights of Mindray DS, nor the rights of others.

Mindray DS intends to maintain the contents of this manual as confidential information.

Disclosure of the information in this manual in any manner whatsoever without the written

permission of Mindray DS is strictly forbidden. Release, amendment, reproduction,

distribution, rental, adaption and translation of this manual in any manner whatsoever without

the written permission of Mindray DS is strictly forbidden.

is a trademark or a registered trademark of Shenzhen Mindray Bio-Medical

Electronics Co., Ltd. All third-party trademarks that appear in this manual are used solely for

editorial purposes and are the property of their respective owners.

Contents of this manual are subject to changes without prior notice.

WARNING

z Federal Law (USA) restricts this device to sale by or on the order of a physician.

FOR YOUR NOTES

Preface

Manual Purpose

This manual provides detailed information about the assembling, dissembling, testing and

troubleshooting of the equipment to support effective troubleshooting and repair. It is not

intended to be a comprehensive, in-depth explanation of the product architecture or technical

implementation. Observance of the manual is a prerequisite for proper equipment

maintenance and prevents equipment damage and personnel injury.

This manual is based on the maximum configuration; therefore, some contents may not apply

to your pulse oximeter. If you have any question, please contact our Customer Service

Department.

Intended Audience

This manual is for biomedical engineers, authorized technicians or service representatives

responsible for troubleshooting, repairing and maintaining the pulse oximeter.

Revision History

This manual has a revision number. This revision number changes whenever the manual is

updated due to software or technical specification change. Contents of this manual are subject

to change without prior notice.

 Revision number: 2.0  Release time: 2010-04

Password

 Maintenance password: 321

III

FOR YOUR NOTES

Contents

1 Safety........... .............................. ... .. ... .............................. ... .. ... .............................. .. .......... 1-1

1.1 Safety Information ..........................................................................................................1-1

1.1.1 Warnings............................................................................................................. 1-2

1.1.2 Cautions ............................................................................................................. 1-2

1.1.3 Notes .................................................................................................................. 1-2

1.2 Equipment Symbols ........................................................................................................ 1-3

2 Theory of Operation ........................................................................................................ 2-1

2.1 Introduction..................................................................................................................... 2-1

2.2 System Connections ........................................................................................................ 2-1

2.2.1 Mounting the Pulse Oximeter ............................................................................ 2-1

2.2.2 Connectors for Peripheral Devices..................................................................... 2-2

2.3 Main Unit ........................................................................................................................ 2-3

2.3.1 Main Control Unit .............................................................................................. 2-3

2.3.2 Power Supply ..................................................................................................... 2-6

2.3.3 Main Board Interfaces........................................................................................ 2-9

2.3.4 SpO

2.3.5 Charger stand ....................................................................................................2-11

Module.................................................................................................... 2-10

3 Testing and Maintenance................................................................................................. 3-1

3.1 Introduction..................................................................................................................... 3-1

3.1.1 Recommended Frequency .................................................................................. 3-2

3.2 Visual Test ....................................................................................................................... 3-3

3.3 Power On Test ................................................................................................................. 3-3

3.4 Performance Tests...........................................................................................................3-4

3.4.1 SpO

3.4.2 SpO

3.5 Electrical Safety Tests .....................................................................................................3-5

3.5.1 Enclosure Leakage Current Test......................................................................... 3-6

3.5.2 Patient Leakage Current Test ............................................................................. 3-6

3.6 Output Interface Test.......................................................................................................3-7

3.6.1 RS232 Port test................................................................................................... 3-7

3.6.2 Infrared Output Test ........................................................................................... 3-7

3.7 Program Upgrade ............................................................................................................ 3-8

4 T ro ubleshooting................................................................................................................ 4-1

4.1 Introduction..................................................................................................................... 4-1

4.2 Part Replacement ............................................................................................................4-1

4.3 Software Version Check.................................................................................................. 4-2

Test............................................................................................................ 3-4

Test in Motion Mode................................................................................. 3-4

4.4 Technical Alarm Check ................................................................................................... 4-2

4.5 Troubleshooting Guide.................................................................................................... 4-3

4.5.1 Power On/Off Failures ....................................................................................... 4-3

4.5.2 Display Failures ................................................................................................. 4-3

4.5.3 Alarm Problems.................................................................................................. 4-4

4.5.4 Button Failure..................................................................................................... 4-4

4.5.5 Interface Failures................................................................................................ 4-4

4.5.6 Power Supply Failures ....................................................................................... 4-5

4.5.7 Software Upgrade Problems............................................................................... 4-5

5 Repair and Disassembly .................................................................................................. 5-1

5.1 Tools................................................................................................................................ 5-1

5.2 Preparations for Disassembly.......................................................................................... 5-1

5.3 Disassembly Guide ......................................................................................................... 5-2

5.3.1 Removing the Covers ......................................................................................... 5-2

5.3.2 Removing the Main Board ................................................................................. 5-4

5.3.3 Removing the Speaker and SpO

Communication Cable Socket....................... 5-4

5.3.4 Removing the LCD Screen ................................................................................ 5-5

5.3.5 Remove the Screen Mount ................................................................................. 5-6

6 Parts .................................................................................................................................. 6-1

6.1 Introduction..................................................................................................................... 6-1

6.2 Main Unit ........................................................................................................................ 6-2

6.3 Front Panel Assembly ..................................................................................................... 6-3

6.4 Main Board Assembly..................................................................................................... 6-4

6.5 Battery Adjusting Bracket Assembly .............................................................................. 6-5

6.6 Rear Cover Assembly...................................................................................................... 6-6

6.7 Replacement Parts...........................................................................................................6-7

1 Safety

1.1 Safety Information

WARNING

z Indicates a potential hazard or unsafe practice that, if not avoided, could result in

death or serious injury.

CAUTION

z Indicates a potential hazard or unsafe practice that, if not avoided, could result in

death or serious injury.

NOTE

z Provides maintenance tips or other useful information.

1-1

1.1.1 Warnings

WARNING

z All installation operations, expansions, changes, modifications and repairs of this

product should be conducted by authorized personnel only.

z Always disconnect the equipment with the charger stand and remove the batteries

before disassembling the equipment.

z Dispose of the packaging material according to local waste control regulations and

your hospital’s waste disposal protocols. Keep the packaging material out of children’s reach.

1.1.2 Cautions

CAUTION

z Make sure that no electromagnetic radiation interferes with the performance of the

equipment when preparing to carry out performance tests. Mobile phone, X-ray equipment and MRI devices are possible sources of interference as they may emit higher levels of electromagnetic radiation.

z Before connecting the charger stand to the AC mai n s, ch eck that the voltage and

frequency ratings of the AC mains meet the specifications indicated on the equipment’s label or in this manual.

z Protect the equipment from damage caused by drop, impact, strong vibration or

other mechanical force during servicing.

1.1.3 Notes

NOTE

z Refer to Operation Manual for detailed operation and other information.

1-2

1.2 Equipment Symbols

Direct Current (DC)

Attention: Consult this manual before maintenance.

Auxiliary output connector

Audio pause

Battery door locked/unlocked

Power supply connector

Left/Right button

Power button

Up button

Down button

Date of manufacture

Serial number

Safety Class II equipment

Type BF applied part, defibrillation protected

The following definition of the WEEE label applies to EU member states

only.

This symbol indicates that this product should not be treated as household

waste. By ensuring that this product is disposed of correctly, you will help

prevent bringing potential negative consequences to the environment and

human health. For more detailed information with regard to returning and

recycling this product, please consult the distributor from whom you

purchased it.

* For system products, this label may be attached to the main unit only.

1-3

FOR YOUR NOTES

1-4

2 Theory of Operation

2.1 Introduction

This pulse oximeter is designed to monitor or measure the oxygen saturation and pulse rate of

single adult, pediatric and neonatal patient.

The pulse oximeter also:

 Presents audible and visual alarms in case of patient or equipment problems.  Enables the real-time displaying, reviewing, storing and exporting of SpO

values.

 Supports Pitch Tone, which means the pitch of pulse tone rises as the oxygen saturation

level increases and falls as the oxygen saturation level decreases.

 Operates on either alkaline batteries or a lithium-ion battery.  Offers wired or wireless communication with a personal computer.

and PR

2.2 System Connections

2.2.1 Mounting the Pulse Oximeter

The pulse oximeter can be mounted on a wall bracket or on a trolley support. The wall

bracket or trolley support can be ordered optionally. Each type of mounting bracket is

delivered with a complete set of mounting hardware and instructions for use. To install the

pulse oximeter, refer to the instrutions for installation.

CAUTION

z Use mounting brackets we supply or approve. If other compatible mounting

bracket is used, be sure it can be safely applied to the pulse oximeter.

z The mounting bracket should be installed by our qualified service personnel, or

mechanical engineers who have adequate knowledge on it.

z If other mounting solution is used, the installation personnel and the customer

should verify if it can be safely applied to the pulse oximeter, and the customer assume the responsibility for any risk resulting from that.

2-1

2.2.2 Connectors for Peripheral Devices

The connectors for peripheral devices are located at the top, right side and bottom of the

pulse oximeter as shown in the figure.

 Multifunctional connector

It is a DB 9 connector which is used to connector a SpO

sensor (including reusable

sensor, disposable sensor and veterinary sensor) to measure the oxygen saturation or

connect a personal computer through a PC communication cable to export trend data.

 Infrared port

It is a port through which a personal computer is communicated using a infrared adapter

to export data in real time without affecting patient monitoring.

 Power supply connector

It is a female power socket which is used to connect the charger stand’s male power

plug . To avoid being mixed with other power supply adapters, it has nonstandard size.

2-2

2.3 Main Unit

The pulse oximeter consists of main board, SpO

charger stand. The main board is composed of a main control unit and a power module.

The following diagram shows the structure of the main unit.

board, display, speaker, batteries and

2.3.1 Main Control Unit

The main control unit provides the system with resources and support. It controls the LCD

screen, alarm LED, speaker, button operation and data storage. It also implements

communication with the SpO

The functional block diagram of the main control unit is shown below:

board, power module and external interfaces.

2-3

2.3.1.1 Power Supply

The power module provides the main control unit with 3.1 V, 2.5 V and 0.9 V power supple.

Label Voltage Applicable parts

DVDD 3.1 V Alarm LEDs, Flash memory, infrared light-emitting IC,

PC communication cable, LCD boost up circuit,

prestage audio optional amplifier.

VDDE 2.5 V DSP peripheral voltage, SDRAM, LCD logic, infrared

logic, buttons and resetting.

VDDINT 0.9 V DSP kernel voltage

2-4

2.3.1.2 Core Control Unit

The Core control unit consists of CPU, SDRAM and Flash memory.

The CPU is ADI’s DSP BF531. Its kernel running frequency is up to 400 MHz and external

frequency up to 133MHz. The kernel voltage is 0.8 V and the current consumed at 50 MHz is

as low as 26mA. The oscillating frequency of the CPU clock is 11.0592 MHz and its

expected frequency is 55MHz, which can be implemented through internal PLL frequency

multiplication. The SDRAM provides space for program running and the Flash memory

provides space for storing program, data, lingual library and configuration information. The

BF531 starts directly from the Flash memory.

2.3.1.3 Man-machine Interfaces

The functions of the buttons are listed below:

Button In measurement mode In menu mode

Audio Pause

button

Up button Increases the beat

Down button Decreases the beat

Left button Enters the main menu Enters a submenu or confirm

Right button Locks/Unlocks buttons. Returns to the previous menu

 LCD screen

It is a 2.4” standard QVGA (320×240) TFT LCD with a 36-pin connector. The LCD is

connected with the BF531 through a bus. 4 LEDs in series are used to backlight the

LCD. The maximum current is 15mA and driving voltage 13.2V. The main control

board provides DC power supply for the LCD and the backlight board.

Pauses audible alarms. Pauses audible alarms.

Moves the cursor upwards or

volume.

increases the value of selected

menu item by one.

Moves the cursor downwards

or decreases the value of selected

menu item by one.

the selection.

or exits the current menu.

 Alarm lamp

The alarm lamp gives visual alarm signals which meet applicable requirements. It

consists of 4 LEDs in parallel. The alarm LEDs receive electrical signal sent by the main

board and convert it into optical signal which is then sent to the panel through a light

conducting bar. The alarm LEDs light up in red and yellow.

2-5

+ 37 hidden pages