Milton CAT TH406 User Manual

Specifications

®

Cat

TH406

Telehandler

Engine

Model
Engine Model (Standard) Cat
Engine Model (Optional) Cat® C4.4 Electronic DITAAC-ACERT
Gross Power (Standard) 74.5 kW 100 hp
Gross Power (Optional) 93.1 kW 125 hp
Maximum Torque (Standard) 410 Nm at 1400 rpm
Maximum Torque (Optional) 496 Nm at 1400 rpm
Bore 105 mm 4.13 in
Stroke 127 mm 4.99 in
Displacement 4.4 L 268.5 in

®

C4.4 Mechanical DITAAC

3

Weights

Operating Weight 7200 kg 15,870 lb

Operating Specifications

Rated Load Capacity 3700 kg 8,150 lb
Maximum Lift Height 6.10 m 20 ft
Maximum Forward Reach 3.11 m 10 ft 2 in
Top Travel Speed 40 kph 25 mph
Capacity at Max Height 2500 kg 5,500 lb
Capacity at Max Reach 1500 kg 3,300 lb
Turning Radius over Tires 3.70 m 12 ft 2 in

Service Refill Capacities

Fuel Tank 150 L 39.63 gal
Hydraulic Tank 90 L 23.78 gal

Tires

Standard 15.5/80-24 16PR
Optional 400/80 R24 Power CL
460/70 R24 XMCL

15.50 x 25 SGL

Brakes

• Service brakes are inboard wet disc brakes on front axle

• Parking brakes are mechanical on front axle

Hydraulic System

Maximum System Pressure 250 bar 3,625 psi
Maximum Pump Flow 150 L/min 39.63 gal/min

™

Pump Type Variable displacement

load sensing axial piston pump

Auxiliary Hydraulic Supply 80 L/min 21.13 gal/min
(Intermittent)

Auxiliary Hydraulic Supply 60 L/min 15.85 gal/min
(Continuous)

• Auxiliary Hydraulic Circuit used for all attachments
equipped with cylinders or other hydraulic components.
Consists of valves, controls, and hydraulic lines.

Transmission Speeds

Forward — 1 7 kph 4.3 mph
Forward — 2 12 kph 7.45 mph
Forward — 3 21 kph 13 mph
Forward — 4 32 kph 19.8 mph
Forward — 5 40 kph 25 mph
Reverse — 1 7 kph 4.3 mph
Reverse — 2 12 kph 7.45 mph
Reverse — 3 21 kph 13 mph

Boom Performance

Boom Up 5 Seconds
Boom Down 4 Seconds
Tele In 4.5 Seconds
Tele Out 5 Seconds
Tilt Forward (dump) 3 Seconds
Tilt Backward 3 Seconds
Combined — Up and Out 8 Seconds
Combined — Down and In 6 Seconds
Drawbar Pull 82.4 kW 8400 kg 18,520 lb
Drawbar Pull 86.8 kW 8849 kg 19,510 lb

Instruments

• Engine speed, boom angle, machine speed, operation hours,
% of continuous flow selected, gear selected and direction

3.7 m

(12 ft)

4.9 m

(16 ft)

2.4 m

(8 ft)

50°

40°

30°

20°

10°

0°

7.3 m (24 ft)

6.1 m (20 ft)

4.9 m (16 ft)

3.7 m (12 ft)

2.4 m (8 ft)

1.2 m (4 ft)

-1.2 m (4 ft)

0 m (0 ft)

2495 kg (5,500 lb)

1996 kg (4,400 lb)

1497 kg (3,300 lb)

TH406 Telehandler

Dimensions

All dimensions are approximate.

2400 mm (94.4 8 in)

Load Chart and Dimensions

232 3 mm
(91.4 6 in)

1753 mm
(69.02 in)

409 mm

(16.10 in)

2950 mm (116.10 in)

4253 mm (167.4 0 in)

4621 mm (181.92 in)

7.3 m (24 ft)

6.1 m (20 ft)

4.9 m (16 ft)

3.7 m (12 ft)

2.4 m (8 ft)

1.2 m (4 ft)

0 m (0 ft)

-1.2 m (4 ft)

4.9 m

(16 ft)

20°

10°

0°

3.7 m

(12 ft)

50°

40°

30°

2000 kg (4,400 lb)

1500 kg (3,300 lb)

2.4 m

(8 ft)

67.5°

C

B

A

2500 kg (5,500 lb)

3000 kg (6,600 lb)

1.2 m

(4 ft)

0 m

(0 ft)

3700 kg
(8,150 lb)

-1.2 m

(4 ft)

IMPORTANT

Rated lift capacities shown are with machine
equipped with carriage and pallet forks. The
machine must be level on a firm surface with
undamaged, properly inflated tires. Machine
specifications and stability are based on rated
lift capacities at specific boom angles and boom
lengths. (If specifications are critical, the proposed
application should be discussed with your dealer.)

DO NOT exceed rated lif t capacity loads, as unstable
and dangerous machine conditions will result.

DO NOT tip the machine forward to determine
the allowable load.

Use only JLG approved attachments with proper
material handler model/attachment load capacity
charts displayed in the operator’s cab. OSHA
requires all rough terrain forklif t operators be
trained according to OSHA 29 CFR 1910.178 (1).

Due to continuous product improvements, machine
specifications and/or equipment changes may
be made without prior notification. This machine
meets or exceeds ANSI/ITSDF B56.6-2005 as
originally manufactured for intended applications.

For more complete information on Cat products, dealer services, and indus try solutions, visit us on t he web at
www.cat .com

© 20 09 Caterpillar
Printed in U.S.A.
All rights reserved.

CAT, CATERPILL AR, their respective logos, “Caterpillar Yellow” and t he POW ER EDGE trade dress , as well as
corporate and product identity used herein, are trademarks of Ca terpillar and may not be used w ithout permission.

AEHQ5965-05 (10-2009)