Operating instructions
for Washing machine
W 3514 WPS
To avoid the risk of accidents or
damage to the machine it is
essential to read these instructions
before it is installed and used for the
first time.
G
M.-Nr. 06 622 900
Caring for our environment
Disposal of the packing
material
The transport and protective packing
has been selected from materials which
are environmentally friendly for disposal
and can normally be recycled.
Ensure that any plastic wrappings,
bags etc. are disposed of safely and
kept out of the reach of babies and
young children. Danger of suffocation!
Rather than just throwing these
materials away, please ensure they are
offered for recycling.
Disposal of your old appliance
or machine
Electrical and electronic appliances /
machines often contain materials
which, if handled or disposed of
incorrectly, could be potentially
hazardous to human health and to the
environment. They are, however,
essential for the correct functioning of
your appliance or machine. Please do
not therefore dispose of your old
machine or appliance with your
household waste.
Please dispose of it at your local
community waste collection / recycling
centre and ensure that it presents no
danger to children while being stored
for disposal.
It should be unplugged or disconnected
from the mains electricity supply by a
competent person. The plug must be
rendered useless and the cable cut off
directly behind it to prevent misuse.
See the "Warning and Safety" section of
this booklet for further details.
Pre-wash with the Heavy Degree of soiling option . . . . . . . . . . . . . . . . . . . . . . . . 63
5
Warning and safety instructions
To avoid the risk of accidents and
damage to the machine please read
these instructions carefully before
using it for the first time. They
contain important information on its
safety, use and maintenance.
Keep these operating instructions in
a safe place and ensure that new
users are familiar with the content.
Pass them on to any future owner of
the machine.
Correct usage
Only use the washing machine to
wash items which are specified by
the manufacturer to be machine-washable on the wash-care label, and textiles composed of hand-washable wool
or wool blend fabrics as well as satin,
lace, silk and other hand-washable
garments.
Any other applications may be dangerous. The manufacturer is not liable for
damage resulting from improper use or
operation.
Technical safety
Before setting up the machine,
check it for any externally visible
damage. Do not install and use a
damaged machine.
Before connecting the machine,
ensure that the connection data on
the data plate (voltage and connected
load) match the mains electricity
supply. If in any doubt, consult a
qualified electrician.
when continuity is complete between
the machine and an effective earthing
system which complies with local and
national regulations. It is most important
that this basic safety requirement is
present and regularly tested and where
there is any doubt the household wiring
system should be inspected by a
qualified electrician.
The manufacturer cannot be held liable
for the consequences of an inadequate
earthing system (e.g. electric shock).
extension lead. Extension leads do not
guarantee the required safety of the
machine (e.g. danger of overheating).
Unauthorised repairs could result in
unforeseen dangers for the user, for
which the manufacturer cannot accept
liability. Repairs should only be
undertaken by a Miele approved
technician.
Ensure current is not supplied to the
machine until after maintenance or
repair work has been carried out.
when:
– it is switched off at the wall socket
and the plug is withdrawn, or
– it is switched off at the mains, or
– the mains fuse is withdrawn.
The electrical safety of this
machine can only be guaranteed
Do not connect the machine to the
mains electricity supply by an
The machine is built in accordance
with current safety requirements.
The machine is only completely
isolated from the electricity supply
6
Warning and safety instructions
The Miele "Water protection
system" protects from water
damage provided the following
conditions have been met:
the machine is correctly plumbed in
–
and connected to the electricity
supply.
if a fault has been identified, the
–
machine must be examined by a
competent person before further use,
and repaired if necessary.
Faulty components must only be
replaced by genuine Miele original
spare parts. Only when these parts are
fitted can the safety standards of the
machine be guaranteed.
If the connection cable is faulty it
must only be replaced by a Miele
approved service technician to protect
the user from danger.
In countries where there are areas
which may be subject to infestation
by cockroaches or other vermin, pay
particular attention to keeping the
machine and its surroundings in a
clean condition at all times. Any
damage which may be caused by
cockroaches or other vermin will not be
covered by the machine guarantee.
Use
This equipment may only be used
in mobile installations such as
ships, caravans, aircraft etc. if a risk
assessment of the installation has been
carried out by a suitably qualified
engineer.
Do not install your washing
machine in rooms where
temperatures below freezing may
occur. Frozen hoses may burst under
pressure. The reliability of the electronic
control unit may be impaired at
temperatures below freezing point.
Before using the machine for the
first time, check that the transit
fitting at the rear of the machine has
been removed (see section on
"Installation"). During spinning, a transit
fitting which is still in place may result in
damage to both the machine and
adjacent furniture or appliances.
Turn off the stopcock if the
machine is to be left for any length
of time (e.g. holiday), especially if there
is no floor drain (gully) in the immediate
vicinity.
Flooding danger
If hooking the drain hose into a
wash basin, check that the water can
drain off quickly enough to prevent the
sink from overflowing.
Make sure the drain hose is secure, so
that the force of the water flowing out of
the hose does not dislodge it.
Take care to ensure that foreign
objects (e.g. nails, pins, coins,
paper clips) do not find their way into
the machine with the laundry. These
may damage components of the
machine (e.g. suds container, drum),
which in turn can result in damage to
the laundry.
7
Warning and safety instructions
If the correct amount of detergent
is dispensed, the machine should
not need to be descaled. If, however,
you do wish to descale the machine
only use proprietary non-corrosive
descaling agents and strictly observe
the instructions on the packaging. If in
doubt, contact the Miele Customer Ser
vice Dept. or your Miele Dealer.
Textiles which have been
pre-treated in solvent based
cleaning agents must be thoroughly
rinsed in clean water before being
washed in the machine.
Never use solvent based cleaning
agents in this machine, as this may
result in damage to component parts
and create toxic fumes. Such
detergents also pose a fire and
explosion hazard.
Only use dyes specified by the
manufacturer as being suitable for
use in a domestic washing machine.
Always observe the manufacturer's
instructions carefully.
Colour run and dye removers
contain sulphur compounds which
can cause damage such as corrosion.
Do not use these products in this
machine.
Always make sure the drum is
stationary before reaching in to
remove washing. Reaching into a
moving drum is extremely dangerous.
Safety with children
This machine is not a toy! To avoid
the risk of injury do not allow
children to play on or near it or to play
with the controls. Supervise its use by
the elderly or infirm, and supervise
children whilst you are operating the
machine.
For machines with a ‘porthole’
door, remember that the porthole
glass will be hot when washing at very
high temperatures. Do not let children
touch it.
Accessories
Accessory parts may only be fitted
when expressly approved by Miele.
If other parts are used, guarantee,
performance and product liability
claims will be invalidated.
Disposal of your old machine
Before discarding an old machine,
switch it off at the wall socket and
unplug it. Render the plug useless. Cut
off the cable directly behind the
appliance to prevent misuse. This
should be done by a competent
person.
The manufacturer cannot be held
liable for damage caused by
non-compliance with these Warning
and Safety instructions.
8
Control panel
Description of the machine
a Programme buttons e-
For selecting a washing programme.
b Soiling button
For specifying the degree of soiling
of the laundry.
Water plus button
For increasing the water level.
c Temperature button
For selecting a temperature.
d Spin speed button
For selecting a final spin speed.
e PC / Optical interface
This is used by service technicians
to run diagnostic checks on your
machine and can also be used to
update programming data in the
future.
f Sequence indicator lights
Show which section of the wash
programme has been reached.
g Buzzer button
h Check lights
i Delay start button
For delaying the start of a
programme.
j Start/Stop button
For starting the programme selected
and cancelling a programme once it
has started.
k I-On/0-Off button
For switching the machine on or off.
l Door button
Opens the machine door.
m Display (h min)
The display fulfills several functions.
See next page for details.
9
Description of the machine
Display
The display shows:
the programme duration (Time left
–
display)
delay start
–
the programmable functions
–
Programme duration
After the start of a programme, the
estimated programme duration will
appear in the display in hours and
minutes.
When delay start is being used, the
programme duration will appear after
the delay start time has elapsed.
During the first 10 minutes the washing
machine measures how much water is
being absorbed by the laundry and
uses this to calculate the load. The
programme duration may be longer or
shorter depending on this absorbency
rate.
Delay start
The delay start time selected will
appear in the display.
After the machine has started, the
delay start time counts down. If the
delay start time is more than 10 hours, it
will count down by the hour. If it is less
than 9 hours and 59 minutes it will
count down minute by minute.
Once the delay start time has finished,
the programme begins and the
estimated programme duration shows
in the display.
Programmable functions
The programmable functions can be
used to tailor washing programmes to
suit your individual requirements. In
programming mode, the display will
show the function selected.
10
Before using the machine for the first
time ensure that it is correctly
installed and connected. See
"Installation and connection". Also
check that the drain filter is securely
tightened to prevent the risk of water
leaks during use.
For safety reasons, spinning is not
possible until the machine has been
prepared for using for the first time. To
activate the spinning function you must
run a wash programme without laundry
and without detergent.
Using detergent could result in an
excessive build-up of foam.
This also activates the ball valve. The
ball valve prevents detergent escaping
from the suds container into the sump
during a wash programme, thus making
maximum use of the detergent.
Before using for the first time
^ Open the stopcock.
^
Press the
The indicator light for the
programme will come on.
^
Press the H programme button to
select the
^
Press the
The programme will begin. When it has
finished, your machine is ready for
using for the first time.
I-On/0-Off
Cottons
Start/Stop
button in.
Automatic
programme.
button.
11
Washing environmentally and economically
Energy and water consumption
Water consumption and energy
–
usage are determined by the size of
the load.
To make the most out of your
machine, load the maximum dry load
for the programme you are using.
Use the
–
programmes for small loads.
When smaller amounts of laundry are
–
washed using the
programme, the automatic load
recognition system will reduce the
amount of water, time and energy
used. This may mean that the time
left shown in the display is adjusted
during the course of the wash
programme.
– Using the
instead of the
programme will give energy savings
of between 35% and 45%.
Detergent
Automatic
Cottons 60°C
and
Express
Cottons
programme
Cottons 95°C
Degree of soiling
With most of the programmes you can
specify the degree of soiling of the
laundry. The washing machine will then
adjust the programme to suit the
degree of soiling.
Light
–
No visible dirt or stains.
Normal
–
Visibly dirty and/or just a few slight
stains.
Heavy
–
Visible dirt and stains as well as
soiling that has dried on or been left
unwashed for a while.
When drying with a tumble dryer
– Selecting the highest possible spin
speed for the wash programme will
save energy when drying in a tumble
dryer afterwards.
–
Do not exceed the amounts of
detergent recommended by the
manufacturer on the packaging.
–
Reduce the amount of detergent with
smaller loads (approx.
the amount recommended can be
used when washing a half load).
12
1
/3less than
How to wash correctly
Brief instructions
The headings numbered A, B, C, . . .
show the operating sequence and can
be used as brief instructions.
A Sort the laundry
^ Empty all pockets.
,
Foreign objects (e.g. nails,
coins, paper clips, etc.) can cause
damage to garments and
components in the machine.
^
Badly soiled areas, stains etc. should
be cleaned as soon as possible,
preferably whilst still fresh. Spillages
should be carefully dabbed off using
a soft colourfast cloth. Do not rub!
Sort the laundry by colour and by
^
care label. Most garments have a
textile care label in the collar or side
seam.
Dark textiles often contain excess dye
and should be washed separately
several times before being included in
a mixed load. Always wash whites and
coloureds separately.
Curtains: Remove lead weights first
–
or place in a laundry bag.
Underwiring and collar stiffeners:
–
Any loose wiring in bras, shirt collar
stiffeners, etc. should be removed or
sewn in.
– Knitted garments, trousers and
jeans, T-shirts and sweat shirts: Turn
inside out, if recommended by the
manufacturer.
– Close any zips, fasten hooks and
eyes etc before washing.
– Fasten duvet covers etc. to prevent
small items from being rolled up
inside them.
Do not wash any items in this machine
which are specified by the
manufacturer as not washable on the
care label. (h symbol)
Badly soiled areas can be pre-treated
with liquid detergent, stain removers
etc. first, following the manufacturer's
instructions. With particularly stubborn
stains ask your dry cleaner for advice.
,
Do not use solvent-based
cleaning agents in this machine.
13
How to wash correctly
B Switch on the washing machine
C Load the drum
Press the
^
drum door.
Unfold the laundry and load loosely
^
in the drum. Mixing both large and
small items gives better wash results
and also helps distribute the load
evenly during spinning.
The most efficient use of energy and
water is achieved when a full load is
washed. However, do not overload as
this causes creases and reduces
cleaning efficiency.
Make sure that no garments are
caught between the drum door and
seal.
Door
button to open the
D Select a programme
Press the e or - button repeatedly
^
until the indicator light for the
programme you want lights up.
^
Shut the door with a gentle swing.
14
How to wash correctly
Specify the degree of soiling of the
laundry
Press the top button to select the
degree of soiling.
setting.
Use the lower button to select the
plus
option.
^ Press the top button repeatedly until
the degree of soiling you want lights
up.
^ Press the
want to activate this function.
You cannot select the degree of soiling
or
Water plus
Normal
Water plus
for every programme.
is the default
button if you
Water
You can change the pre-set
temperature or spin speed by pressing
the Temperature or Spin button.
In some programmes the maximum
temperature and spin speed is limited.
The machine will not allow a higher
value to be selected.
^ Press the Temperature or Spin
button repeatedly until the indicator
light for the value you want comes
on.
^
Press the
be reminded when the programme is
finished.
Buzzer
button if you want to
15
How to wash correctly
E Add detergent
It is important to dispense the correct
amount, because . . .
. . . too little detergent results in:
Laundry not getting properly clean
–
and with time it may become grey
and hard to the touch.
Greasy particles clinging to the
–
laundry.
Limescale deposits on the heater
–
elements.
. . . too much detergent results in:
– Excessive foam which causes a low
level of agitation and poor wash,
rinse and spin results.
Pull out the detergent drawer and
^
place detergent in the compartments
as follows:
i
– Higher water consumption (an
additional rinse cycle will
automatically switch in).
– A burden to the environment.
Detergent for the pre-wash (if the
Degree of soiling
Heavy
, add1/4of the total amount
recommended).
j
Detergent for the main wash
§
Fabric conditioner or liquid starch.
^
Close the detergent drawer.
See "Detergent" for further information.
has been set as
16
How to wash correctly
F Select Delay Start, if wished
Delay start allows you to delay the start
of a programme from 30 minutes up to
a maximum of 24 hours, allowing you to
make use of night-time economy
electricity rates, for example.
Press the
^
press on the button increases the
delay start time:
by 30 minutes up to 10 hours,
–
by 1 hour from 10 hours upwards.
–
To cancel Delay start
^ Press the
when 24 ^ is showing in the display.
To cancel Delay start after you have
pressed the
^ You will have to cancel the
programme. See relevant section
later in this booklet.
G Start the programme
Delay start
Delay start
Start
button:
button. Each
button once
Remove the laundry.
^
Only remove laundry from the
machine once the drum has
stopped turning. Reaching into a
moving drum is extremely
dangerous and could result in injury.
Check that all items have been
removed from the drum. Items left in
the drum could discolour other items
in the next wash or become
discoloured themselves.
^
Press the flashing
The estimated programme duration will
then show in the display. This will count
down in one minute steps. During the
first 10 minutes the machine measures
how much water is being absorbed by
the laundry. The programme duration
may be longer or shorter depending on
this absorbency rate.
H Remove the laundry when the
programme as finished
The
Finish
and
indicator lights will come on when the
programme is finished.
^
Press the
drum door.
Door
Start/Stop
Anti-crease
button to open the
Sequence
button.
^
Check the folds in the door seal for
any small articles, e.g. buttons which
might be lodged there.
^
Switch the washing machine off with
I-On/0-Off
^
Close the drum door. Otherwise there
is the danger of objects being placed
inadvertently in the drum. If these
remained unnoticed and were
washed in the next load, they could
damage the laundry.
button.
17
Degree of soiling, Water plus, Buzzer
The washing machine will adjust the
programme to suit the degree of soiling
selected.
Light
No visible dirt or stains.
The duration of the main wash is
reduced.
Normal
Visibly dirty and/or just a few slight
stains.
The standard wash programme will be
carried out.
Heavy
Visible dirt and stains and/or dried on
soiling.
A fifteen minute pre-wash will be
carried out and the duration of the main
wash will be increased by 15 minutes.
Water plus
If the
Water plus
water level in the main wash and rinses
is increased.
You can also alter the setting allocated
to the
Water plus
"Programmable functions".
button is pressed, the
button. See
Buzzer
The buzzer will sound at the end of the
programme or when Rinse hold has
been reached.
The buzzer will sound repeatedly until
the machine is switched off.
Once switched on, the buzzer is active
in all programmes until it is switched off
again.
You can also change the volume of the
buzzer or deactivate the buzzer button.
See "Programmable functions".
The buzzer will always sound when
there is a fault, even if it has been
deactivated.
The
Pre-wash
will flash. Add the appropriate amount
of powder detergent to compartment
i.
You can also deactivate the Pre-wash
and increase the duration of the main
wash by 30 or 60 minutes instead of the
standard default increase of 15
minutes. See "Programmable functions".
You can reduce the final spin speed.
However, you cannot select a final spin
speed higher than that shown in the
chart above.
Rinse and interim spin
There is a spin after the main wash and
between the rinses. A reduction in the
final spin speed will also reduce the
interim spin speed. If a spin speed of
less than 700 rpm is selected for a
Cottons
is introduced.
programme, an additional rinse
To omit the final spin (Rinse hold)
Select the
^
Rinse hold
setting. The
laundry will not be spun and will
remain suspended in the final rinse
water. This reduces creasing if the
laundry is not going to be removed
from the drum immediately after the
end of the programme.
To start the final spin
–
:
The Rinse hold indicator light will
illuminate. Select the spin speed you
want by pressing the spin speed
button until the indicator light next to
the spin speed you want illuminates.
The washing machine will then start
the final spin.
– To end the programme
Press the
Door
button. The water will
drain away. Press the
:
Door
button
again to open the door.
To omit rinse and interim spin and
the final spin
Select the
Without spin
setting. The
laundry is not spun after the final rinse.
The water will drain away and the
machine will go straight into the
anti-crease stage. An additional rinse is
introduced if this settnig is selected
with the
iron/Delicates
Automatic,Cottons,Minimum
and
Express
programmes.
19
Programme chart
Automatic cold to 40°C 76e21fMax. load 3.5 kg
FabricMixed loads of garments suitable for the
iron/Delicates
Cottons 30°C to 95°C 9ö8E76Max. load 6.0 kg
FabricCotton and linen fabrics, e.g. bed linen, table linen, towelling,
jeans, underwear, T-shirts, nappies.
Notes
Note for test institutes:
Programme setting for testing according to EN 60456 standard: Cottons 60°C
Short programme: 3.0 kg load and
Minimum iron/Delicates cold to 60°C
8E764321
FabricSynthetic fibres, mixed fibres, rayon and easy care cottons.
Notes– Due to the large amount of fine dust in curtains, we
Only use the
–
laundry.
Use the
–
Curtains, including net curtains, specified as machine-washable
by the manufacturer.
recommend selecting the
also the
kg.
–
For curtains which crease easily, reduce the spin speed or
select Without spin.
programmes. Sort according to colour.
Cottons 95°C
Dark garments
Light
programme for heavily soiled
programme for dark coloured items.
Degree of soiling setting
Heavy
Water plus
option. Only wash a maximum load of 2
Cottons
Degree of soiling setting and
and
Minimum
Max. load 3.0 kg
Note for test institutes:
Programme setting for testing according to EN 60456 standard: Minimum iron/
Delicates 40°C and spin speed of 1200 rpm
20
Loading...
+ 44 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.