Miele T8402C User Manual

Operating instructions

for condenser tumble dryer T 8402 C

To avoid the risk of accidents or damage to the appliance it is essential to read these instructions before it is installed and used for the first time.

en-GB

M.-Nr. 07 868 870

Caring for the environment

Disposal of the packing material

The transport and protective packing has been selected from materials which are environmentally friendly for disposal and should be recycled.

Ensure that any plastic wrappings, bags, etc are disposed of safely and kept out of the reach of babies and young children. Danger of suffocation.

Disposal of your old appliance

Electrical and electronic appliances often contain materials which, if handled or disposed of incorrectly could be potentially hazardous to human health and to the environment. They are, however, essential for the correct functioning of your appliance. Please do not therefore dispose it with your household waste.

Energy saving tips

To avoid unnecessarily long drying times and high consumption of energy:

Make sure that your laundry is

–

thoroughly spun before drying.

The higher the spin, the greater the savings that can be made in energy and time during drying.

Load according to the optimum

–

amount of laundry recommended for the programme being used (see Programme chart).

Underloading is uneconomical. Overloading gives a poorer quality of drying and may cause unnecessary creasing.

– Make sure the room in which the

dryer is located is well ventilated.

– Make sure the fluff filters are clean

before using the dryer.

– Check the condenser unit from time

to time and clean it when necessary.

Please dispose of it at your local community waste recycling centre or contact your dealer for advice. Ensure that it presents no danger to children while being stored for disposal.

Contents

Caring for the environment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Warning and Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Notes on laundry care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Care symbols.....................................................14

Tips on drying ....................................................14

How to dry correctly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Brief instructions ..................................................15

Low temperature................................................16

Changing the programme sequence ..................................17

Changing a programme once it has started...........................17

Cancelling a programme once it has started and then selecting a different

programme ....................................................17

Cancelling a programme once it has started and then removing the laundry . 17

Adding or removing laundry after a programme has started ..............17

Programme chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Cleaning and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Emptying the condensed water container...............................20

Cleaning the fluff filters .............................................21

Cleaning them whilst dry .........................................21

Cleaning them with water .........................................22

Cleaning the tumble dryer ...........................................23

Cleaning the condenser unit .........................................24

Removing the condenser unit......................................24

Checking the condenser unit ......................................25

Cleaning the condenser unit.......................................25

Replacing the condenser unit......................................26

Problem solving guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

General problems .................................................27

Check and fault messages ..........................................30

Changing the lamp ................................................31

After Sales service. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Repairs..........................................................32

Future updates (PC) ...............................................32

Appliance guarantee ...............................................32

Optional accessories ...............................................32

Contents

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Front view........................................................33

Rear view ........................................................34

Installation site ....................................................34

Transporting the tumble dryer to its installation site .....................34

Building under a continous worktop / in a kitchen run ...................34

Levelling the tumble dryer ........................................35

Room in which the dryer is located .................................35

Washer-dryer stack..............................................35

Before moving the tumble dryer again (e.g. when moving house) .........35

External condensed water outlet ......................................36

Arranging the drain hose .........................................36

External drainage via a sink or gully ................................37

Installation conditions requiring a non-return valve .....................37

Consumption data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Programmable functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Altering the residual moisture level in the Cottons programmes..............42

Altering the residual moisture level in the Minimum iron programme ..........43

Anti-crease ......................................................44

Activating and deactivating the buzzer .................................45

Altering the standard drying level in the Automatic programme..............46

Extending the cooling down time .....................................47

Standby .........................................................48

Warning and Safety instructions

It is essential to read these instructions.

This tumble dryer conforms to current safety requirements. Inappropriate use can, however, lead to personal injury and damage to property.

To avoid the risk of accidents and damage to the tumble dryer, please read these instructions carefully before using it for the first time. They contain important information on its safety, installation, use and maintenance.

Keep these instructions in a safe place and ensure that new users are familiar with the content. Pass them on to any future owner.

Correct application

This tumble dryer is not designed for commercial use. It is

intended for use in domestic households and similar working and residential environments.

The tumble dryer is not intended for outdoor use.

It must only be used as a domestic appliance to dry items which

have been washed in a water solution and which are marked on the manufacturer's care label as being suitable for tumble drying. If using dry cleaning kits, do so at your own risk, and follow the instructions provided on the packaging. Any other usage is not supported by the manufacturer and could be dangerous. Miele cannot be held liable for damage resulting from incorrect or improper use or operation.

Warning and Safety instructions

The tumble dryer can only be used by people with reduced

physical, sensory or mental capabilities, or lack of experience or knowledge, if they are are supervised whilst using it or have been shown how to use it in a safe way and understand the hazards involved.

Safety with children

Children under 8 years of age must be kept away from the tumble

dryer unless they are constantly supervised.

Children 8 years and older may only use, clean or maintain the

tumble dryer without supervision if they have been shown how to do so in a safe way and understand the hazards involved.

The tumble dryer is not a toy! To prevent the risk of injury, do not

allow children to play with it or near it, or to play with the controls.

Warning and Safety instructions

Technical safety

Before setting up the tumble dryer, check it for any externally

visible damage. Do not install or use a damaged tumble dryer.

Before connecting the tumble dryer, ensure that the connection

data on the data plate (voltage and frequency) match the mains electricity supply. If in any doubt, consult a qualified electrician.

The electrical safety of this tumble dryer can only be guaranteed

when correctly earthed. It is most important that this basic safety requirement is observed and regularly tested, and where there is any doubt, the household wiring system should be inspected by a qualified electrician. Miele cannot be held liable for the consequences of an inadequate earthing system (e.g. electric shock).

Do not connect the tumble dryer to the mains electricity supply by

an extension lead. Extension leads do not guarantee the required safety of the tumble dryer (e.g. danger of overheating).

If the electrical connection cable is faulty it must only be replaced

by a Miele approved service technician to protect the user from danger.

Unauthorised repairs could result in unforeseen dangers for the

user, for which Miele cannot accept liability. Repairs should only be undertaken by a Miele approved service technician, otherwise any subsequent damage will not be covered by the guarantee. Ensure current is not supplied to the tumble dryer until after maintenance or repair work has been carried out.

Warning and Safety instructions

Faulty components must only be replaced by genuine Miele

original spare parts. Only when these parts are fitted can the safety standards of the tumble dryer be guaranteed.

The tumble dryer must be isolated from the electricity supply in

the event of a fault and during cleaning and maintenance.

The tumble dryer must not be used in a non-stationary location

(e.g. on a ship).

Do not make any alterations to the tumble dryer, unless

authorised to do so by Miele.

In areas which may be subject to infestation by cockroaches or

other vermin, pay particular attention to keeping the tumble dryer and its surroundings in a clean condition at all times. Any damage which may be caused by cockroaches or other vermin will not be covered by the guarantee.

Warning and Safety instructions

Correct use

To prevent the risk of fire, the following textiles must not be dried

in this appliance:

items which have not been washed.

–

items, such as workwear, which have not been thoroughly

–

cleaned and which are still soiled with grease, oil or other deposits (such as cosmetics, lotions etc). If items have not been thoroughly cleaned there is a danger that these might self-ignite when heated, even after they have been removed from the dryer at the end of the programme.

– items (e.g. mops and floor cloths) which have been treated with

inflammable cleaning agents or which contain residues of acetone, alcohol, benzine, petrol, kerosene, stain remover, turpentine, wax and wax remover or other chemicals.

– items which have been splashed with hair lacquer, hair spray, nail

varnish remover or similar substances.

When washing such heavily soiled items, ensure that you use additional detergent and select a high temperature. If in doubt, wash the items several times.

Remove all items such as lighters and matches from pockets.

Warning: Do not switch the tumble dryer off before the drying

programme has finished. If this is done, the laundry must be hung up or spread out to cool it down.

Warning and Safety instructions

Danger.

This tumble dryer must not be connected to a controllable socket (e.g. a timer switch or a peak load shut-off device). If the dryer programme were to be interrupted before the end of the cooling down phase, the laundry could self-combust.

To prevent the risk of fire, the following must not be tumble dried:

items which have been cleaned using chemicals (e.g.

–

professional dry-cleaning agents).

fabrics which contain a large proportion of rubber, foam rubber or

–

rubber-like materials. For example, products made from latex foam rubber, shower caps, waterproof textiles, rubberised articles and items of clothing and pillows with foam rubber filling.

– damaged items which contain padding or fillings (e.g. pillows,

jackets). When damaged, the filling can get out with the risk of igniting in the dryer.

In many programmes, the heating phase is followed by a cooling

down phase to ensure that the items are not too hot to handle when you remove them (this also avoids the danger of the laundry self-igniting). The programme is not finished until the cooling down phase has been completed. As soon as the programme has finished, remove all laundry from the drum.

Fabric conditioner and similar products must be used according

to the instructions on the manufacturer's packaging.

Do not let anyone sit or lean on the door, as this can cause the

tumble dryer to tip up.

Always close the door after use. This way you will avoid the

danger of: –

children climbing into the dryer or hiding things in it.

–

pets or other small animals climbing into it.

Warning and Safety instructions

The dryer must not be used without the fluff filters in place or if

the fluff filters are damaged in any way.

The fluff filters must be cleaned regularly.

The dryer must not be used without the condenser unit in place.

The fluff filters must be thoroughly dried after cleaning. Damp or

wet filters could cause operational faults.

Do not install the tumble dryer in a room where there is a risk of

frost occurring. At temperatures around freezing point the tumble dryer may not be able to operate properly. There is a risk of damage if the condensed water is allowed to freeze in the pump and in the drain hose. The ambient room temperature should be between +2°C and +35°C.

If the water is drained externally instead of being collected in the

condensed water container, make sure the drain hose is securely attached if you hang it in a sink or basin to avoid the hose slipping and the water causing damage.

Condensed water is not drinking water.

It can cause health problems in both people and animals.

Always keep the area around the tumble dryer free of dust and

fluff. Dust drawn into the tumble dryer can cause blockages in the condenser unit over time.

The tumble dryer must not be hosed down.

Warning and Safety instructions

Accessories

Only use genuine Miele original spare parts and accessories with

this tumble dryer. If non-Miele parts are used, guarantee, performance and product liability claims may be invalidated.

Miele cannot be held liable for damage caused by non-compliance with these Warning and Safety instructions.

Control panel

a Programme selector

The programme selector can be turned clockwise or anti-clockwise.

b Programme sequence and check

lamps

c Start button

Press the Start button to start a programme. The Start indicator lamp will flash as soon as a programme can be started. It lights up constantly once the programme has started.

d I-On/0-Off button

To switch the appliance on or off / to interrupt a programme.

The Finish/Anti-crease lamp will light up as confirmation that the tumble dryer has been switched on.

e Door Button

To open the door / to cancel a programme. Pressing this button will open the door even when the appliance is switched off at the mains.

If the appliance is switched on at the mains and the door is opened the drum lighting will come on. It will go out a few minutes later to save energy.

Notes on laundry care

Care symbols

Before drying check the drying symbol on the care label. If there are no symbols, dry at your own risk!

q .........Dryatnormal temperature

r ..........Dryatalowtemperature

s ...............Donottumble dry

For delicates and fabrics with the

–

following care label r select Low temperature.

Tips on drying

– Always observe the maximum

recommended loads given in the "Programme chart". Never overload the drum.

Overloading can cause unnecessary wear and tear to the laundry, give a disappointing drying result and cause more creasing.

– Do not put soaking wet items into the

tumble dryer. Spin them thoroughly after washing using the appropriate spin speed.

–

Use the Automatic programme for drying mixed loads of cottons and minimum iron fabrics.

–

Open jackets evenly.

–

Woollens and wool blends become matted and shrink if dried in a tumble dryer. They can, however, be partially dried using the Woollens handcare programme.

so that they can dry

tend to

Down-filled garments

–

which have a tendency to shrink, depending on the quality of the item. They can be partially dried using the Smoothing programme.

Pure linen

–

dried if specified as suitable by the manufacturer on the care label, as the surface of the fabric may otherwise become rough. It can be partially dried using the Smoothing programme.

Loopknit garments

–

underwear) tend to shrink depending on their quality. Do not over-dry these textiles. When purchasing these garments it is advisable to take their shrinkage properties into account.

– Minimum iron fabrics

more, the greater the load. This is also the case for garments made from very fine weave fabrics, such as shirts or blouses. If in doubt, reduce the load or use the Minimum iron - Hand iron programme.

–

Starched laundry tumble dryer. To achieve the usual finish, double the amount of starch should be used.

–

New dark coloured garments be washed and dried separately from light coloured garments to avoid the danger of colours running and discolouring other garments or even plastic components in the appliance. Dark coloured fibres can also settle on light coloured garments and vice versa.

should only be machine

have linings

(e.g. T-shirts and

tend to crease

can be dried in the

should

How to dry correctly

Brief instructions

The headings numbered (A, B, C ...) show the operating sequence and can be used as a brief guide to using your dryer.

A Sort the laundry

To ensure an even drying result separate the washed laundry and sort it according to: . . . the drying level required . . . the type of fibre or weave . . . size . . . the moisture content after spinning.

Make sure that objects e.g.

detergent dispensing balls have been removed from the laundry. They could melt, and cause damage to the dryer or the laundry.

– Check seams and stitching to ensure

that padding and linings are intact.

– Fasten duvet covers and pillow

cases to prevent small items from being trapped inside them.

C Load the tumble dryer

Press the Door button to open the

door.

Load the laundry loosely into the

drum.

Do not overload the drum. See the "Programme chart" for recommended loads for each programme. Overloading can cause unnecessary wear and tear to the laundry and give a disappointing drying result.

^ Before closing the door make sure

the fluff filter is correctly positioned.

–

Fasten hooks and eyes etc.

–

Tie fabric belts and apron strings.

–

Sew in or remove underwiring from bras.

B Turn on the tumble dryer

Switch the dryer on by pressing the jk button.

The tumble dryer may be switched on after loading, saving energy as the lighting will not come on.

Check the laundry is right inside the drum so that it cannot get trapped or damaged when the door is shut.

Shut the door either with a gentle swing, or lean against it and push it shut.

How to dry correctly

D Select a programme

Turn the programme selector to the

required programme.

Low temperature

^ For drying particularly sensitive

fabrics (care symbol r) e.g. acrylics turn the programme selector to the Low temperature position.

Because the heater rating is reduced for the Low temperature setting, clothes dry more slowly thus lengthening drying times.

E Start the programme

Press the Start button.

The indicator lamp for the Start button will then change from flashing to being on constantly. The drying cycle begins.

Depending on the programme selected, the drying stage reached is shown by the sequence indicator lamps on the right hand side of the control panel.

Before the end of a programme

The cooling down phase takes place before the end of a programme so that the garments are not too hot to handle (the Cool air indicator lamp will come on). The programme is not finished until the cooling down phase is complete. The Woollens handcare and Smoothing programmes do not include a cooling down phase.

At the end of a programme

The Finish/Anti-crease indicator lamp comes on.

The drum will continue to rotate at intervals to prevent laundry creasing, if you do not wish to remove it immediate ly. The anti-crease phase lasts for an hour. There is no anti-crease phase on the Woollens handcare programme.

During the anti-crease phase... . . . (depending on the programme selected) the indicator lamp for the drying stage reached will also light up. . . . the buzzer will sound at intervals.

How to dry correctly

F Remove the laundry

Press the Door button.

Open the door.

Remove the laundry.

Check that all items have been removed from the drum. If items are left in the dryer, they could be damaged by overdrying when the dryer is next used.

Switch the dryer off by pressing the

l-On/0-Off button.

^ Clean the fluff filters.

^ Close the door.

^ Empty the condensed water

container (unless the dryer has been connected for external drainage).

^ The condenser unit should be

checked and cleaned on a regular basis (see "Cleaning and care").

Changing the programme sequence

Changing a programme once it has started

You cannot change to another programme once a programme has started (this prevents unintentional alterations). If you try and change a programme the Finish/Anti-crease light will start flashing.

Cancelling a programme once it has started and then selecting a different programme

Turn the programme selector to

Finish.

Press the Door button.

Close the door.

Select another programme and start

it.

Cancelling a programme once it has started and then removing the laundry

^ Proceed as described in "Adding or

removing laundry after a programme has started" below.

^ Switch the dryer off after closing the

door.

Adding or removing laundry after a programme has started

^ Press the Door button.

Open the door.

Danger of burning: Do not touch the back of the drum when adding or removing items. The drum and the items can get very hot.

Add or remove items as required.

Close the door.

Press the Start button.

You will need to cancel the current programme before you can select a new one.

Programme chart

Cottons Max. load: 6 kg*

Normal+, Normal**, Low temperature

Fabric type Single and multi-layered cottons fabrics such as towelling,

jerseywear, underwear, flannelette bed linen.

Note

Hand iron, Machine iron

Fabric type Cottons and linen fabrics, e.g. table linen, bedlinen, starched

Note To prevent laundry from drying out it should be rolled up until you

Minimum iron Max. load: 3 kg*

Normal, Low temperature, Hand iron

Fabric type Minimum iron items made of cotton, synthetic or blended fabrics,

Notes – Select Low temperature for fabrics with the r symbol (e.g.

* Weight of dry laundry ** Note for test institutes:

Test programme in accordance with Regulation 392/2012/EU for energy labelling measured in accordance with EN 61121

Select Low temperature for fabrics with the r symbol. Laundry

–

is dried at a lower temperature.

laundry.

are ready for ironing.

e.g. shirts, blouses, skirts and table cloths.

acrylic garments). Laundry is dried at a lower temperature.

– Select Hand iron for delicate fabrics and to reduce creasing

even more, reduce the load to 1.5 kg*.

– In the Minimum iron Hand iron programme, items are dried with

very little creasing, depending on fabric type and amount of load.

Programme chart

Automatic Max. load: 3.5 kg*

Fabric type Mixed load of garments suitable for Cottons and Minimum iron

programmes.

Timed drying Max. load: 6 kg*

Warm air

Fabric type

Cool air

Fabric type Any item which only needs airing.

Woollens handcare Max. load: 2 kg*

Fabric type Woollen fabrics

Notes – To refresh and fluff up woollen garments quickly. Woollen

Smoothing Max. load: 3 kg*

Fabric type – Cottons and linen fabrics.

Notes – Smooths out creasing caused during the spin cycle in the

* Weight of dry laundry

Multi-layered fabrics whose layers have different drying

–

characteristics, e.g. jackets, pillows. For drying individual items, e.g. bath towels, swimwear,

–

tea-towels.

fabrics are not dried completely by this programme.

– Remove garments as soon as the programme has finished and

leave to finish drying at room temperature.

– Minimum iron mixed fibre, cotton or synthetic items, e.g.

trousers, jackets, shirts.

washing machine.

–

Fabrics are not completely dried in this programme. Remove garments as soon as the programme has finished and leave to finish drying at room temperature.

Cleaning and care

Emptying the condensed water container

The condensed water will be collected in the condensed water container unless the tumble dryer has been fitted with a drain hose (see installation).

The condensed water container should be emptied after every

drying cycle or as soon as the

Empty out container indicator lamp comes on.

The drying programme will be interrupted if the maximum level of the condensed water container is reached. The Empty out container indicator lamp comes on and the buzzer sounds.

Grip the container firmly with both hands, as shown, and pull it out slightly towards the right-hand side.

Hold the container with both hands and carry it in a horizontal position.

^ Open the shutter and empty out the

water.

^ To replace the container hold it at a

slight angle (as when removing it) and push it in gently until you feel it click into position.

^ Before starting a new programme,

first switch the tumble dryer off and then on again. The Empty out container indicator lamp will go out.

Condensed water should not be consumed. It could lead to health problems for people and animals.

Condensed water can be put to household use (e.g. used in a steam iron or humidifier). To ensure that any residual particles of fluff in the condensed water are removed before use, pass it through a fine sieve or paper filter first.

Cleaning and care

Cleaning the fluff filters

The fluff which is created by the drying process is collected by the fluff filters in the door and the door opening. Clean the filters after each drying programme.

Cleaning them whilst dry

Tip: You can also use a vacuum cleaner.

^ Open the door and pull the fluff filter

(1) out of the door as illustrated.

Remove any fluff from the hollow part

of the door holder. A cleaning brush is available as an optional extra from Miele or use a vacuum cleaner.

Once clean, push the filter back into

the door holder until it clicks into position. Ensure it is facing the correct way.

Also clean the door seal (2) with a

damp cloth.

Use your fingers to remove the fluff from the two fluff filters in the door opening.

Use your fingers to remove the fluff from the surface of the filter.

Close the door.

Cleaning and care

Cleaning them with water

If there is a great deal of compacted fluff on any of the filters, they can be removed and cleaned under hot running water.

Open the door and pull the fluff filter

out of the door as described previously.

The two filters in the door opening can also be removed if you need to clean them with water.

Do not replace them if they are

damp or wet. Damp or wet filters could cause operational faults.

Push the large filter back into the

door holder until it clicks into position. Ensure it is facing the correct way.

Replace the filters in the door

opening by first inserting them at the bottom and then pressing them into place at the top.

Lock both dials.

Turn dial a and pull the filter by the dial out of the door opening as shown b. Do the same on the other side.

Rinse all the filters under hot, running water.

Then shake the filters until no more water droplets are visible.

Dry the filters thoroughly with care.

Clean the area underneath these filters, e.g. with a vacuum cleaner.

Cleaning the tumble dryer

Disconnect the tumble dryer from the mains electricity supply.

Miele branded cleaning and conditioning products are available to order via the internet on www.miele-shop.com.

Clean the housing and control panel

with a slightly damp cloth and a mild detergent or soapy water.

The drum and other stainless steel

parts can be cleaned with a suitable stainless steel cleaner following the manufacturer's instructions.

Do not use solvents, abrasive cleaners, glass cleaners or all-purpose cleaners. These could damage plastic sufaces and other parts.

Cleaning and care

^ Dry all parts with a soft cloth.

Cleaning and care

Cleaning the condenser unit

Detergent residue, hair and fine fluff from the dryer can get through the fluff filters and block the condenser unit.

Dust from the room in which the dryer is installed can also get into the condenser unit and cause a blockage.

Check the condenser unit at least once a year. If the dryer is used frequently then clean the condenser unit on a regular basis.

Removing the condenser unit

Turn the lever on the inner cover

downwards to the vertical position.

^ Pull the cover forwards

^ Then remove it by pulling it

diagonally upwards.

Use the yellow lever supplied to open the service panel.

Insert the lever into the middle of the gap at the top (see arrow)

Now remove the panel by pulling it diagonally upwards. Then place it to one side.

Turn the lever on the condenser unit to the vertical position so that the hook on the lever is no longer in the groove at the bottom of the condenser unit housing.

Pull the condenser unit out of its

housing by the handle.

Checking the condenser unit

Cleaning and care

If you cannot see any fluff:

Replace the condenser unit (see

following page).

If you can see some fluff:

Clean the condenser unit as

described below.

Cleaning the condenser unit

When rinsing the condenser unit,

make sure you position it as shown in the next two illustrations.

Hold the condenser unit up to the light as shown.

Check to see if there is any fluff inside it. The arrows in the illustration above indicate where to look.

Use a shower head or similar to rinse the unit out as shown.

Cleaning and care

Then flush the unit through from the

front.

^ Check the condenser unit again for

any visible fluff and if necessary flush it through again until it has all gone.

Replacing the condenser unit

With the handle facing upwards,

push the condenser unit back into position in its housing.

Turn the lever down to the horizontal

position, making sure that the hook on the lever clicks into the groove.

When replacing the inner cover after cleaning, ensure that the rubber seal fits correctly into the groove.

Replace the inner cover making sure

the hooks locate correctly. Hold it at an angle and push it gently downwards.

^ Then turn the lever upwards into the

horizontal position to lock the cover.

^ Repeat as required.

^ Also make sure the rubber seals are

clean. The rubber seals must not be removed and must be free of kinks.

Shake the water off the condenser unit until no more droplets of water are visible.

Checking and cleaning the condenser unit housing

Remove any soiling still visible inside the housing unit by hand using a damp cloth. Do not try and access areas you cannot reach by hand!

^ Replace the service panel and press

the upper edge until it clicks into position.

It is important to ensure that both the condenser unit and the cover are correctly positioned and locked, otherwise water may leak from the dryer.

Problem solving guide

With the help of the following notes minor faults in the performance of the appliance, some of which may result from incorrect operation, can be put right without contacting the Service Department.

Repair work to electrical appliances should only be carried out by a

suitably qualified person in strict accordance with current local and national safety regulations. Repairs and other work by unqualified persons could be dangerous. The manufacturer cannot be held liable for unauthorised work.

General problems

Problem Possible cause Remedy

The programme does not start.

Power cut. A programme which was running previously will

Items made of synthetic fibres are charged with static electricity after drying.

The Start button indicator light flashes slowly.

No obvious cause.

continue automatically when power is restored to the tumble dryer as long as the Cooling down phase had not been reached.

Synthetic fibres tend to attract static charge.

The dryer is in Standby mode. This is quite normal and not indicative of any fault.

Is the dryer switched

–

on?

– Is the plug correctly

inserted into the socket and switched on?

– Is the door closed

properly?

– Has the fuse or circuit

breaker tripped?

Static charge can be reduced by adding a fabric conditioner to the final rinse in the washing programme or a fabric conditioner sheet to the load when drying.

See "Programmable functions".

Problem solving guide

Problem Possible cause Remedy

There is a build-up of fluff.

The laundry is not sufficiently dry.

Water leaks from the tumble dryer after the condenser unit has been cleaned.

The interior drum lighting does not come on.

* You can alter the residual moisture levels for some programmes. See "Programmable functions" at the end of this booklet.

Fluff is principally the result of friction when garments are being worn and washed. Machine drying hardly causes any fluff to form and has been established by research institutes to have no appreciable effect on the lifetime of fabric.

The load consisted of different fabric.

– The inner cover of the

condenser unit has not been locked properly and/or the condenser unit has not been positioned correctly.

– Fluff has collected in the

condenser unit housing.

The lighting switches off automatically (to save energy).

The light needs changing. Change the light as

Fluff is collected by the fluff filters and can be easily removed (see "Cleaning and care").

Finish drying using the

–

Warm air programme. Select a more suitable

–

drying programme next time* (see "Programme chart").

– Ensure that the

condenser unit is positioned correctly and

lock the inner cover. – Check the rubber seals. – Use a cloth to remove

any visible fluff from the

inside of the condenser

unit housing.

Switch the dryer off and then on again.

described at the end of this section.

Problem solving guide

Problem Possible cause Remedy

Drying is taking too long, or the programme has been cancelled

* Before attempting to remedy the problem:

–

Open and close the door.

–

Switch the dryer off and then on again to start a programme.

The dryer is not working efficiently or economically*.

The most likely cause is a build-up of fluff, hair or detergent residue on the fluff filters.

Ventilation to and from the dryer may be insufficient (e.g because it is installed in a small room). This has caused the temperature in the room to rise sharply.

The vents below the door are blocked.

Detergent residue, hair and fine fibres can block the condenser unit.

The laundry has not been spun sufficiently.

The tumble dryer has been overloaded.

Metallic components, e.g. zips have prevented the dryer from registering the correct moisture level in the laundry.

Remove any fluff, hair or

–

residual detergent. Rinse the filters if necessary

–

and then dry them thoroughly before replacing them. If not thoroughly dry faults will occur.

If the above measures do

–

not remedy the problem follow the advice below.

Open a door or window

–

while the tumble dryer is in operation for increased air flow.

– Remove any objects that

are blocking the vents.

– Check the condenser unit

from time to time and clean it if necessary (see "Cleaning and Care").

–

Make sure that your laundry is thoroughly spun at the appropriate spin speed.

–

Do not exceed the maximum load for the programme selected.

–

Open zips next time.

–

If the problem occurs again, dry garments with long zips using "Warm air" (timed drying).

Problem solving guide

Check and fault messages

Problem Possible cause Remedy The Empty container

indicator light comes on.

The programme stops and the Machine iron or Hand iron indicator light flashes.

The buzzer sounds.

The Finish/ Anti-crease indicator light flashes while drying is in progress.

The programme stops and the Finish/ Anti-crease indicator light comes on.

The buzzer sounds.

The Cooling down indicator light comes on. The buzzer sounds.

The condensed water container is full or there is kink in the drain hose.

No obvious cause.

The programme selector was moved after the start of a programme. The programme continues to run as normal.

This is not a fault. The electronic unit has

recognised that there is not enough laundry in the drum and cancelled the programme.

Drying items which are already dry can also cause the programme to be cancelled.

The dryer is not working efficiently or economically.

Empty the condensed

–

water container. Check the drain hose.

–

The indicator light will

–

go out if you open and close the door.

Switch the dryer off and

–

then on again. Then start the

–

programme again.

If the programme stops again and the indicator light flashes again there is a fault. Contact the Miele Service Department.

Turn the selector back to the original position and the indicator light will go out.

Use the Warm air programme (timed drying) to dry individual items.

Before changing a programme: Open and close the door.

See the previous page under "Drying is taking too long ...".

Changing the lamp

Disconnect the tumble dryer from the mains electricity supply.

Problem solving guide

The light specification and maximum wattage is stated on the data plate and on the light cover.

Open the door.

You will find the interior light cover at the top of the drum aperture.

^ Insert a suitable tool, such as a wide

bladed screwdriver, under the side edge of the light cover as illustrated.

Apply a little pressure and whilst doing so turn your wrist in the direction of the arrow to open the cover.

Turn the light anti-clockwise to

remove.

Replace the lamp.

To close the cover push it upwards

and press it on the left and right until you hear it click into position.

Ensure that it is fitted into

position securely, as any moisture could cause a short circuit.

The cover will open downwards.

The temperature resistant lamp should only be ordered from your Miele Dealer or the Miele Spare Parts Department.

After Sales service

Repairs

In the event of any faults which you cannot remedy yourself, please contact

your Miele dealer or

–

the Miele Service Department (see

–

back cover for contact details).

When contacting your dealer or the Service Department, please quote the model and serial number of your appliance, both of which are shown on the data plate. This is visible when you open the door.

N.B. A call-out charge will be applied for service visits where the problem could have been resolved as described in these instructions.

Future updates (PC)

The indicator or check light marked PC on the fascia panel is the interface used by the Miele service technicians during service work for testing purposes and for updating the appliance's programme data.

Appliance guarantee

In the U.K. your appliance is guaranteed for 2 years from the date of purchase. However you must activate your cover by calling 0845 365 6640 or registering online at www. miele.co.uk.

For information on the appliance guarantee specific to your country please contact Miele. See back cover for contact details.

Optional accessories

Optional accessories for this dryer are available from your Miele Dealer, the Miele Spare Parts Department or via the internet at www.miele-shop.com.

Please note that telephone calls may be monitored and recorded for training purposes.

Front view

Installation

a Mains connection cable

b Condensed water container

c Control panel

d Door

e Service panel for condenser unit

f Four height-adjustable screw feet

g External drainage options (e.g. via

wash basin, wash basin drain outlet, or gully. See "External condensed water outlet").

Installation

Rear view

a Protruding lid for holding when

moving the appliance (see arrows)

b Air inlet vent for cooling the

condenser unit

c Mains connection cable

d External drainage of the condensed

water

e Accessories for connection to a sink

drain outlet

Installation site

Make sure the dryer door can be opened without hindrance after installation.

Transporting the tumble dryer to its installation site

When moving the appliance, you can hold it by the lid where it protrudes to the rear of the dryer. To manoeuvre the dryer out of its packing case to its installation site hold it by the front feet and at the back of the lid. Do not lift the appliance by the drum door.

Building under a continous worktop / in a kitchen run

A building-under kit* with a

coverplate to replace the appliance lid is required. It must be fitted by a suitably qualified person to ensure electrical safety.

N.B. If you wish to push your appliance under a worktop and there is space to do this without removing the lid the building under kit is not necessary. Otherwise the building under kit is essential.

– The building-under kit is supplied

with its own installation instructions.

– N.B. When built under drying times

may be longer.

– The electrical socket must be

located in an accessible position near the tumble dryer.

With niche heights of:

–

830-840 mm, longer screw feet* are required.

–

870-885 / 915-930 mm, one or two raising kits* are required.

* accessory available to order.

Replacing the lid

If the lid has been removed in order to fit a coverplate, ensure that, if the lid is ever replaced, it fits securely into the rear holders. Otherwise, it is not properly secure for transport.

Levelling the tumble dryer

The appliance must be perfectly level to ensure safe and proper operation.

Installation

Do not block the gap between

the bottom of the tumble dryer and the floor with plinth facings, deep pile carpet etc. This would hinder a sufficient flow of air to the dryer.

Room in which the dryer is located

Air taken in for the drying process will be warm when it is expelled from the front of the dryer. This expelled air heats up the air in the room. It is therefore very important to ensure that the room is adequately ventilated, particularly if the dryer is located in a small room. Otherwise drying durations may be longer.

Washer-dryer stack

The tumble dryer can also be combined with a Miele washing machine in a washer-dryer stack. The appropriate "WTV" stacking kit (available to order) to match your dryer is required.

The screw feet can be adjusted to compensate for any unevenness in the floor.

The air inlet and outlet vents on the front of the tumble dryer must not be covered as this would prevent sufficient ventilation for cooling the condenser unit.

Stacking kits must only be

installed by a suitably qualified fitter.

Before moving the tumble dryer again (e.g. when moving house)

After each use a small quantity of condensed water will collect in the area around the pump. This water can run out if the tumble dryer is tipped up when it is being moved. It is a good idea to run the Cool air programme for approximately 1 minute before moving the tumble dryer Any remaining condensed water will then be fed into the condensed water container or out through the drain hose.

Installation

External condensed water outlet

General notes

When drying is in progress, condensed water is pumped into the condensed water container through the drain hose at the back of the dryer. The condensed water can also be drained off directly if the tumble dryer is installed near a sink, drain outlet etc. so that the condensed water container does not have to be emptied.

Drain hose length ............1.50 m

Maximum delivery head .......1.50 m

Maximum drain hose length ....4.00 m

If the on-site water drainage

system is not fitted with a non-return valve or an appropriate air gap, one must be fitted to prevent the risk of back-flow. (See "Installation conditions requiring a non-return valve").

There will be a small amount of

residual water in the drain hose. Have a container ready to collect this.

^ Pull the hose off its connection (see

arrow).

^ Allow any residual water to run into

the container.

^ Unwind the hose and pull it carefully

out of the holders.

The following optional accessories are available:

–

an extension hose

–

a non-return valve kit for connection to an external condensed water outlet (includes an extension hose). Maximum delivery head with non-return valve fitted: 1.00 m

Arranging the drain hose

Do not pull on the drain hose and do not stretch it or allow it to become kinked as it could get damaged.

Position the hose to the right or left hand side as necessary.

Leave the hose in the middle holder to prevent it from becoming kinked inadvertently.

Installation

External drainage via a sink or gully

See "Front view" illustration.

If you want to drain the water off

into a sink you will need to secure the hose carefully, e.g. by tying it to a tap to make sure it cannot slip during use. Otherwise there is a risk of overflowing water which could cause damage.

Use the bow-shaped guide to

prevent the drain hose from becoming kinked.

Installation conditions requiring a non-return valve

Certain installation conditions

require the fitting of a non-return valve for external water connection (available as an

optional accessory). A non-return valve will prevent the risk of back-flow out of the dryer which could cause damage.

Example: Connection to a sink drain outlet

The drain hose with non-return valve fitted can be connected directly to a suitable sink drain outlet.

^ Remove the following from the back

of the dryer at the top: Adapter 1 and hose clip 3 behind it.

A non-return valve is required:

–

If the tumble dryer is connected to a sink drain outlet (see the following section).

–

If the tumble dryer is connected to a drainage system already in use by another appliance, e.g. a dishwasher or washing machine.

Installation

1 Adapter

Fit adapter 1 to the sink drain outlet

using nut 2.

If this nut has a flat disc in it you should take the disc out first.

Attach the end of hose 4 to adapter

Use a screwdriver to tighten hose

clip 3 up close to the nut.

Non-return valve 5 has to be

fitted with the arrow pointing in the direction of flow (i.e. towards the sink). Otherwise water will not drain out of the appliance.

2 Nut

3 Hose clip

4 End of the hose

5 Non-return valve

6 Tumble dryer drain hose

^ Fit non-return valve 5 to tumble dryer

drain hose 6 (make sure it is fitted in the correct direction - see arrow on non-return valve).

^ Secure the non-return valve using

hose clips.

Consumption data

Programme Load Final spin speed in a domestic

washing machine

kg* rpm kWh Minutes

Cottons Normal 6.0 1000 (60 % residual moisture)**

1200 (53 % residual moisture) 1400 (50 % residual moisture) 1600 (48 % residual moisture) 1800 (43 % residual moisture)

Cottons Hand iron 6.0 1000 (60 % residual moisture)

1200 (53 % residual moisture) 1400 (50 % residual moisture) 1600 (48 % residual moisture) 1800 (43 % residual moisture)

Minimum iron Normal 3.0 1200 (40 % residual moisture) 1.20 37

Minimum iron Hand iron 3.0 1200 (40 % residual moisture) 1.00 32

Automatic 3.5 800 (60 % residual moisture) 2.10 85

Woollens handcare 2.0 1000 (60 % residual moisture) 0.15 4

Smoothing 3.0 1000 (60 % residual moisture) 0.30 8

* Weight of dry laundry ** Test programme in accordance with Regulation 392/2012/EU for energy labelling measured in

accordance with EN 61121 All data without a "star" against it was calculated using EN 61121 Before testing in accordance with EN 61121, drya3kgload of cotton laundry with 70% residual

moisture as per the above standard using the Cottons Normal programme.

Consumption data can vary from the nominal values given above depending on the size of the load, type of textiles, residual moisture levels after spinning and fluctuations in the electricity supply.

Energy Time

3.30

3.00

2.85

2.55

2.50

2.65

2.35

2.20

1.85

1.80

89 81 78 70 69

71 63 60 52 51

Technical data

Height 850 mm

Width 595 mm

Depth 587 mm

Depth with door open 1062 mm

Height for building under 820 mm

Width for building under 600 mm

Depth for building under 600 mm

Suitable for pushing under a worktop Yes

Suitable for stacking Yes

Weight 51 kg

Drum volume 111 litres

Maximum capacity 6 kg dry weight

Capacity of condensed water container approx. 3.5 litres

Drain hose length 1.5 m

Maximum delivery head 1.5 m

Maximum drain hose length 4 m

Length of connection cable 2 m

Voltage see data plate

Connected load see data plate

Fuse rating see data plate / plug

Lamp wattage see data plate

Energy consumption see "Consumption data"

Test certificates awarded see data plate

Programmable functions for changing default settings

The programmable functions are used to alter the tumble dryer´s electronics to suit changing requirements. Programmable functions can be altered at any time.

Programmable functions

Altering the residual moisture level in the Cottons programmes

The tumble dryer is designed to dry effectively using as little energy as possible. However, if you require the laundry to be drier or damper, you can increase or reduce the default residual moisture in the Cottons programmes.

Follow the steps (A,B,C ...) to programme and store in memory.

Before you begin, ensure that:

– The tumble dryer is switched off.

– The door is closed.

– The programme selector is at Finish.

A Press the Start button and keep it

pressed in whilst carrying out steps

B-C.

B Switch the dryer on.

The Cool air lamp will flash once.

The flashing sequence of the Drying lamp shows which option is currently selected.

If the Drying lamp is not flashing:

–

the residual moisture level will be

increased and laundry will be damper.

If the Drying lamp flashes once: the

–

residual moisture level will remain on the standard setting (factory default setting).

– If the Drying lamp flashes twice:

the residual moisture level will be reduced and laundry will be drier.

E Pressing the Start button switches

between the 3 options.

F Switch the dryer off.

The setting you have selected is now stored in memory. You can change it again at any time.

C Wait until the Start indicator lamp

lights up constantly...

D . . . and then release the Start button.

To check the setting:

Carry out steps A to D.

Switch the dryer off after checking the setting as described above.

Programmable functions

Altering the residual moisture level in the Minimum iron programme

The tumble dryer is designed to dry effectively using as little energy as possible. However, if you require the laundry to be drier or damper, you can reduce or increase the default residual moisture in the Minimum iron programme.

Follow the steps (A,B,C ...) to programme and store in memory.

Before you begin, ensure that:

– The tumble dryer is switched off.

– The door is closed.

– The programme selector is at Finish.

A Press the Start button and keep it

pressed in whilst carrying out steps

B-C.

B Switch the dryer on.

C Wait until the Start indicator lamp

lights up constantly...

D . . . and then release the Start button.

E Turn the programme selector to

Cottons Normal+.

The Cool air lamp will flash twice.

The flashing sequence of the Drying lamp shows which option is currently selected.

If the Drying lamp is not flashing:

–

the residual moisture level will be

increased and laundry will be damper.

If the Drying lamp flashes once: the

–

residual moisture level will remain on the standard setting (factory default setting).

– If the Drying lamp flashes twice:

the residual moisture level will be reduced and laundry will be drier.

F Pressing the Start button switches

between the 3 options.

G Switch the dryer off.

The setting you have selected is now stored in memory. You can change it again at any time.

To check the setting:

Carry out steps A to E.

Switch the dryer off after checking the setting as described above.

Programmable functions

Anti-crease

If laundry is not removed as soon as the programme has finished, the drum will continue to rotate at intervals for two hours to prevent creasing.

The anti-crease function

is activated when the tumble dryer is

–

delivered. You can shorten the

duration of the anti-crease phase or

deactivate it if wished.

is used in all programmes except

–

Woollens handcare.

– should be left activated.

Follow the steps (A,B,C ...) to programme and store in memory.

Before you begin, ensure that:

– The tumble dryer is switched off.

– The door is closed.

–

The programme selector is at Finish.

A Press the Start button and keep it

pressed in whilst carrying out steps

B-C.

E Turn the programme selector to

Cottons Normal.

The Cool air lamp will flash three times.

The flashing sequence of the Drying lamp shows which option is currently selected.

If the Drying lamp is not flashing:

–

Anti-crease is deactivated

If the Drying lamp flashes once:

–

Anti-crease will last for 1 hour

If the Drying lamp flashes twice:

–

Anti-crease will last for 2 hours

(factory default setting).

F Pressing the Start button switches

between the 3 options.

G Switch the dryer off.

The setting you have selected is now stored in memory. You can change it again at any time.

To check the setting:

Carry out steps A to E.

Switch the dryer off after checking the setting as described above.

B Switch the dryer on.

C Wait until the Start indicator lamp

lights up constantly...

D . . . and then release the Start button.

Programmable functions

Activating and deactivating the buzzer

A buzzer sounds (at intervals for a maximum of 1 hour) to let you know the programme has finished.

The tumble dryer is delivered with the buzzer activated but you can deactivate it if wished.

If there is a fault, a continuous tone will sound even if the buzzer has been deactivated.

Follow the steps (A,B,C ...) to programme and store in memory.

Before you begin, ensure that:

– The tumble dryer is switched off.

– The door is closed.

– The programme selector is at Finish.

A Press the Start button and keep it

pressed in whilst carrying out steps

B-C.

B Switch the dryer on.

E Turn the programme selector to

Cottons Low temperature.

The Cool air lamp will flash four times.

The flashing sequence of the Drying lamp shows which option is currently selected.

If the Drying lamp is not flashing:

–

the buzzer is deactivated

If the Drying lamp is flashing:

–

the buzzer is activated (factory default setting).

F Pressing the Start button switches

between the 2 options.

G Switch the dryer off.

The setting you have selected is now stored in memory. You can change it again at any time.

To check the setting:

^ Carry out steps A to E.

Switch the dryer off after checking the setting as described above.

C Wait until the Start indicator lamp

lights up constantly...

D . . . and then release the Start button.

Programmable functions

Altering the standard drying level in the Automatic programme

The drying level for this programme is set at a standard Normal level. You have the option of changing this to an increased Normal+ (drier than

Normal)ortoHand iron (damper than Normal) drying level.

Follow the steps (A,B,C ...) to programme and store in memory.

Before you begin, ensure that:

– The tumble dryer is switched off.

– The door is closed.

– The programme selector is at Finish.

A Press the Start button and keep it

pressed in whilst carrying out steps

B-C.

B Switch the dryer on.

C Wait until the Start indicator lamp

lights up constantly...

E Turn the programme selector to

Machine iron.

The Cool air lamp will flash six times.

The flashing sequence of the Drying lamp shows which option is currently selected.

If the Drying lamp is not flashing:

–

the standard drying level is Hand iron

If the Drying lamp flashes once: the

–

standard drying level will remain on the Normal setting (factory default setting).

– If the Drying lamp flashes twice:

the standard drying level is Normal+.

F Pressing the Start button switches

between the 3 options.

G Switch the dryer off.

The setting you have selected is now stored in memory. You can change it again at any time.

D . . . and then release the Start button.

To check the setting:

Carry out steps A to E.

Switch the dryer off after checking the setting as described above.

Programmable functions

Extending the cooling down time

The cooling down phase which takes place before the end of a programme can be lengthened if required. This makes the garments easier to handle.

The dryer is delivered with the extended cooling down time option deactivated. You can extend the cooling down time by 5 minutes or 10 minutes.

The option of extending the cooling down time is available with the Cottons, Minimum iron and Automatic programmes.

Follow the steps (A,B,C ...) to programme and store in memory.

Before you begin, ensure that:

– The tumble dryer is switched off.

– The door is closed.

–

The programme selector is at Finish.

A Press the Start button and keep it

pressed in whilst carrying out steps

B-C.

B Switch the dryer on.

C Wait until the Start indicator lamp

lights up constantly...

E Turn the programme selector to

Smoothing.

The Cool air lamp will flash seven times.

The flashing sequence of the Drying lamp shows which option is currently selected.

If the Drying indicator lamp is not

–

flashing: the cooling down time is

not extended (factory default setting).

If the Drying lamp flashes once:

–

the cooling down time will be extended by five minutes.

– If the Drying lamp flashes twice:

the cooling down time will be extended by ten minutes.

F Pressing the Start button switches

between the 3 options.

G Switch the dryer off.

The setting you have selected is now stored in memory. You can change it again at any time.

To check the setting:

Carry out steps A to E.

Switch the dryer off after checking the setting as described above.

D . . . and then release the Start button.

Programmable functions

Standby

To save energy, the programme sequence/check lights go out and the indicator light for the Start button starts flashing slowly.

To come out of standby mode

Turn the programme selector or

press the Start button. Neither will have any effect if a programme is running.

The standby function is activated and the programme sequence/check lights will go out after 10 minutes:

– if a programme is not selected after

the dryer has been switched on.

– after a programme has started.

They will, however, come on for 10 minutes at the end of the programme or the end of the anti-crease phase. The buzzer (if selected ) will sound for 10 minutes at the end of the programme.

Factory default. Not in current programme

As described under "On" above. However, they will stay on after the programme has started and remain visible during the programme.

Off

The programme sequence/check lights will stay on while the dryer is switched on.

Follow the steps (A,B,C ...) to programme and store in memory.

^ See next page.

Programmable functions

Before you begin, ensure that:

The tumble dryer is switched off.

–

The door is closed.

–

The programme selector is at Finish.

–

A Press the Start button and keep it

pressed in whilst carrying out steps

B-C.

B Switch the dryer on.

C Wait until the Start indicator light

lights up constantly...

D . . . and then release the Start button.

E Turn the programme selector to

Woollens handcare.

The Cooling down light will flash eight times.

The flashing sequence of the Drying light shows which option is currently selected.

If the Drying light is not flashing:

–

On has been selected.

If the Drying light flashes once:

–

Factory default. Not in current programme has been selected.

– If the Drying light flashes twice:

Off has been selected.

F Pressing the Start button switches

between the 3 options.

G Switch the dryer off.

The setting you have selected is now stored in memory. You can change it again at any time.

To check the setting:

Carry out steps A to E.

Switch the dryer off after checking the setting as described above.

495051

Alteration rights reserved/4512

M.-Nr. 07 868 870 / 03

Miele T8402C User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual