Miele PFD 101, PFD 101 i, PFD 101 U Installation diagram

Installation plan

PFD 101
PFD 101 i
PFD 101 U

en-GB

M.-Nr. 11 673 200

Contents

Installation notes ............................................................................................................. 3

Installation requirements ............................................................................................... 3

Environmental requirements.......................................................................................... 3

Electrical connection ..................................................................................................... 3

Water connection .......................................................................................................... 4

Appliance dimensions and installation dimensions..................................................... 6

Freestanding appliance ..................................................................................................... 6

Built-in appliance/built-under appliance ........................................................................... 6

Front panel dimensions PFD101i .................................................................................... 6

Connections..................................................................................................................... 7

Connections on the back of the appliance ....................................................................... 7

On-site connections .......................................................................................................... 7

External dispensing ........................................................................................................... 8

Technical data.................................................................................................................. 9

Dimensions and weights ................................................................................................... 9

Emission levels.................................................................................................................. 9

Electrical connection ......................................................................................................... 10

Water inlet ......................................................................................................................... 10

Drain .................................................................................................................................. 10

Operating conditions......................................................................................................... 11

Storage and transportation conditions.............................................................................. 11

2

Installation notes

Installation notes

For safe installation and commissioning of the dishwasher please
read the installation plan, the service documentation, the installa­tion sheet and the operating instructions.

This installation plan includes the dimensions of the appliance, the
technical data and the requirements to be met on site for the installa­tion of the dishwasher.

Installation re­quirements

Environmental re­quirements

Vapour barrier film
for built-in appli­ances

Electrical connec­tion

Plug connection

Hard-wired

This dishwasher must only be installed and commissioned by the
Miele Customer Service Department, a Miele authorised dealer or a
suitably qualified specialist.

Installation should only be performed in accordance with valid reg­ulations, relevant standards and health and safety codes.

Condensate can build up in the area surrounding the dishwasher. Any
furniture and fittings in the room must therefore be suitable for pur­pose.

The vapour barrier film supplied protects the worktop from damage
caused by steam when the door is opened. Attach the vapour barrier
film above the door, underneath the worktop.

All work on the electrical connection must be carried out by the Miele
Customer Service Department, an authorised Miele dealer or a quali­fied electrician.

The dishwasher should be connected to the electricity supply via a
suitably rated plug and socket.

If the dishwasher is hard-wired to the power supply, a power switch
capable of disconnecting the dishwasher at all poles must be in­stalled on site. This power switch must have a contact gap of at least
3mm.

Residual current device (RCD)

Equipotential bonding

The socket and the power switch must be accessible after the appli­ance has been installed. An electrical safety test can then easily be
carried out, e.g., after any service or maintenance work.
The connection cable must be protected from the risk of thermal
damage.

For increased safety, it is recommended to protect the dishwasher
with a residual current device (RCD) with a trip current of 30mA.

There is a screw connection point for equipotential bonding at the
back of the dishwasher.
Equipotential bonding should be carried out if possible on site.

3

Installation notes

Water connection

Water inlet

The dishwasher must only be connected to fully vented pipework.
A brief increase in the water pressure can damage components of
the dishwasher.

The quality of the incoming water must correspond to the drinking
water specification of the country in which the dishwasher is being
operated.

The dishwasher must be connected to the water supply in strict ac­cordance with current local and national water authority regulations. It
can be connected to cold or hot water supplies. Connecting the dish­washer to a hot water supply will reduce programme running times.
For short programme running times, dynamic water pressure of at
least 200kPa is also required.

UK installation requirements:

The double check valve supplied with this product must be installed
between the stopcock and the water inlet hose.
Screw the double check valve onto the stopcock. Then screw the
water inlet hose with the water protection system onto the thread of
the double check valve.

If a stopcock is not available, only a qualified installer may connect
the dishwasher to the mains water supply.

The stopcock should remain accessible once the dishwasher has
been installed so that the water supply can be shut off whenever the
appliance is not in use.

4