Miele B3847, B3312 User Manual
fold here
AUTOMATIC RINSING / AUTOMATIC DESCALING
➨
fold here fold here fold here fold here fold here
Automatic rinsing / descaling Automatic descaling Automatic descaling Frequently asked questions Frequently asked questions
Start
Finish
Start
Automatic rinsing
ĺ Adjust the steam ironing system to its highest working height.
ĺ If the message "Fill water container" is shown in the display, fill the water cont-
ainer (see "Filling the water container").
ĺ If the message "Empty residual water container" is shown in the display, remo-
ve and empty the residual water container.
ĺ Clean and dry the residual water container.
Make sure that the metal disks (contacts) at the top of the residual water container are cleaned and dried properly. These metal discs send a signal to the
steam ironing system when the residual water container is full or if it is inserted
into the tower.
The discs will not function correctly if they are dirty or damp.
ĺ Slide the residual water container back into the tower until the container clicks
into place.
Automatic descaling
The steam ironing system must be descaled regularly to ensure that it functions
correctly.
The messages in the display will guide you through the descaling process. The
entire descaling process takes approx. 90minutes.
To optimize the descaling process, start the procedure while the system is still
cold after switching the steam ironing system on.
This way, you avoid a delay of up to 3hours that may be caused by the cooldown phase.
ĺ Remove the steam hose of the iron or the steamer from
the steam connection on the tower.
ĺ Select "Descale".
ĺ Confirm the selection by pressing the OK button.
ĺ Select "Start descaling".
ĺ Confirm the selection by pressing the OK button.
Filling with descaler
ĺ Fill the water container with fresh water up to the level
marking.
ĺ Add 1 descaling tablet to the water container.
ĺ Press the OKbutton to display the next process step.
ĺ Put the water container back into the tower.
ĺ Follow the instructions in the display.
Emptying the residual water container
ĺ Set the steam ironing system to its highest working posi-
tion in order to remove the residual water container when
prompted to do so.
ĺ Remove the residual water container from the tower.
ĺ Drain the residual water container.
ĺ Clean and dry the residual water container.
Make sure that the metal disks (contacts) at the top of the residual water container are cleaned and dried properly.
ĺ Slide the residual water container back into the tower until
the container clicks into place.
Clean the water container and fill it up to the level marking
ĺ Remove the residual water container out of the tower when prompted to do so.
ĺ Rinse the water container thoroughly. Make sure there are no residues of the
descaling tablets remaining in the water container.
ĺ Fill the water container with fresh water at least up to the level marking.
ĺ Put the water container back into the tower.
Descaling
After an activation period of approx. 1hour, the descaling solution is drained
from the steam generator into the residual water container.
The steam generator is then rinsed with water. This rinse cycle takes approx.
5minutes. During this time, the "Rinse (5 min.)" message is displayed.
During the rinsing cycle, the display shows "Rinsing".
As soon as the rinse cycle is completed, the water is drained completely into the
residual water container and the message "Empty residual water container" is
displayed.
Rinsing the soleplate
The iron must not be warm from previous use. Let the iron cool down for at least
60minutes before rinsing the soleplate.
ĺ Make sure that the non-stick soleplate has been removed from the iron.
If the non-stick soleplate is still on the iron, remove it now.
ĺ Refill the water container with fresh tap water.
ĺ Set the temperature selector on the iron to cold so that the
line on the selector is pointing to the indicator light.
ĺ Plug the steam hose of the iron into the steam connection
on the tower.
ĺ If the steam ironing system is switched off, switch it on
now.
As soon as the steam ironing system is ready for use and
steam is available, proceed with the next step.
ĺ Hold the iron over a sink or a heat-resistant container.
During the rinsing process, hot water and steam come out of the iron.
Danger of injury by burning. Never direct the iron at people, animals or
electrical appliances of any kind.
ĺ Press the button on the iron for around a minute and tilt the iron. with the tip
of the iron pointing downward slightly.
Hot water and steam will come out of the iron and dislodge any deposits that
have built up. As soon as there is only steam coming out, you can release the
button.
ĺ Now set the temperature selector on the iron to the highest
temperature settingLinen/Cotton.
The indicator light on the temperature selector will light up
yellow while the iron is heating up. As soon as the indicator
light goes out, the rinsing process is complete.
ĺ Move the iron over a soft, absorbent cotton cloth while it is
still hot. Press the steam button briefly 2-3 times in the
process.
The descaling process is now complete. The steam ironing
system can now be switched off or used.
Finish
With the help of the following guide, minor faults in the performance of the appliance,
some of which may result from incorrect operation, can be remedied without contacting
the Service Department. For further details, see the operating instructions.
Problem Possible cause and solution
The steam ironing
system cannot be
switched on.
The height of the
ironing board cannot be adjusted.
The iron does not
heat up.
The appliance does not have any power.
ĺ Check whether
- the plug is plugged in.
- the fuse in your fuse panel is OK.
The ironing board is not locked into place on both sides of the
tower.
ĺ Use both hands to pull the ironing board upwards into a ho-
rizontal position until this audibly clicks into place on both sides of the tower.
The appliance is switched o.
ĺ Use the button on the control panel to switch the steam iro-
ning system on.
The steam hose is not plugged in properly.
ĺ Plug the steam hose into the steam connection on the tower
again.
The iron has not been used for some time.
ĺ Move the iron or activate the steam button .
The steam button is locked.
ĺ Unlock the steam button by pushing the slider on the iron
forward.
The temperature set on the temperature controller has
already been reached.
ĺ Set the temperature controller to a higher temperature if
necessary.
The appliance is rinsing.
ĺ Wait until the rinsing process has been completed (see "Au-
tomatic rinsing").
The display is indicating a malfunction.
ĺ Please remedy the indicated fault as described in the opera-
ting instructions.
The steam ironing system is damaged.
ĺ Contact Miele Service.
Problem Possible cause and solution
When using the
steam button on
the iron, drops of
water or deposits
escape from the
steam nozzles.
The fan on the
ironing board is not
running.
The temperature selected is too low.
ĺ Set the temperature selector on the iron to at least tempera-
ture setting Silk/Wool.
The iron has not yet
reached the selected temperature.
ĺ Wait until the iron has reached the selected ironing
temperature.
During a longer ironing break, condensation
has accumulated in the steam hose.
ĺ After a break in ironing, do not direct the first burst of steam
onto the garment.
Deposits have formed in the soleplate.
ĺ Rinse the soleplate as described in "Automatic descaling".
Steam was not used.
ĺ The fan only runs when the steam function on the iron is
activated
The steam is not ready yet.
ĺ Wait until the message "Ready" appears in
the display to indicate that steam is ready.
The water container is empty or missing.
ĺ Refill the water container with fresh tap water and replace it
in the tower.
The steamer is connected to the steam ironing system.
ĺ The fan only runs when the iron is connected. Connect the
iron if required.
There is a fault with the steam ironing system.
ĺ Contact Miele Service.
Frequently asked questions
Frequently asked questions
Display
message
Drain valve fault
Switch on/off
Release steam
button
Drain valve fault
Switch on/off
Possible cause and solution
The descaling or rinsing processes have not been
carried out properly.
ĺ Press the button to switch the steam ironing system off
and then back on again.
ĺ If the fault message continues to be displayed, contact Mie-
le Service.
The iron has switched itself o because it has not been used for
a period of time
and the steam button has locked.
ĺ Unlock the steam button by pushing the slider for conti-
nual steam on the iron forward.
The residual water container has not been detected.
ĺ Press the button to switch the steam ironing system off
and then back on again.
After switching the steam ironing system o and back on, the
residual water container has not been detected.
ĺ Press the button to switch the appliance off.
ĺ Clean and dry the metal disks (contacts) on the residual wa-
ter container.
ĺ Use the button to switch the steam ironing system back
on and follow the instructions shown in the display:
ĺ Remove the residual water container and fill it with fresh tap
water.
ĺ Put the filled residual water container back in the tower.
ĺ Remove the residual water container again when you are
prompted to do so by the appropriate message in the
display.
ĺ Empty and dry the residual water container.
ĺ Put the empty residual water container back in the tower.
The steam ironing system is ready for use again and continues with the process that had been started when the fault was
detected.
There is a fault with the steam ironing system.
ĺ If the fault message continues to be displayed, contact Mie-
le Service.
Quick Start Guide
Steam Ironing System
FashionMaster
These short instructions are not a substitute for the operating instructions
supplied with the appliance!
It is essential to familiarize yourself with the steam ironing system before using
it for the first time. Take note of the operating instructions, as well as the
"IMPORTANT SAFETY INSTRUCTIONS".
en-US,CA M.-No. 10 462 481 / 02
Frequently asked questions
fold here
fold herefold herefold herefold herefold here
fold here
SWITCHING ON / IRONING
DESCRIPTION
Set water
click!
click!
fold here fold here fold here fold here fold here
Before using for the first time Description
When using the steam ironing system
for the first time the water hardness level
must be set.
Make sure the correct water hardness
level is set. An incorrect setting will invalidate all warranty claims. Please read the
separate Operating Instructions supplied
with the appliance.
Setting the water hardness level
a Ironing board i X-Frame for the ironing board
ĺ Confirm the display message "Set water
hardness level" by pressing the OK button.
Level 7
ĺ Use the arrow buttons or on the con-
trol panel to set the water hardness level for your household (see chart in "Before using for the first time" in the Operating
instructions).
Level 10
ĺ Confirm your selection by pressing the OK
button.
The steam ironing system is now set for the
specified water hardness.
b Iron with steam hose j Iron resting surface
c Steam hose holder k Power cord
d Handle l Storage compartment (lower)
e Water container For the power cord, Steamer*,
f Tower anti-stick soleplate and clip for the
g Residual water container power cord.
h Storage compartment (upper) m Wheels
For the iron and Steam hose holder. n Release mechanism
For setting up the steam ironing system.
* Standard equipment for steam ironing system B 3847.
Available as optional accessory for steam ironing systems B 3312 and B 3826.
a Rotary dial for height adjustment and
folding the appliance away
b Iron resting surface
c Steam connection
d Steam hose holders
e Control panel
f Steam hose holder
g Iron with steam hose
h On/Off button
i Display
Displays messages and instructions
for the user.
j Arrow button
Lights up if additional options are provided or the display text exceeds the
specified length of a line. Scrolls down
the selection list to the next option or
decreases a value.
k Arrow button
Lights up if additional options are provided or the display text exceeds the
specified length of a line. Scrolls up
the selection list to the next option or
increases a value.
l OK button
Confirms the selection or the information in the display.
m Settings button
Opens the settings menu. In the settings menu, the language and the level of the water hardness can be adjusted, or the descaling process can
be started.
Assembly
1. Set up steam Ironing system
ĺ Use one hand to pull the release
mechanism upwards.
This releases the locking mechanism of the ironing board and the
X-frame folds down.
ĺ Hold onto the release mecha-
nism and guide the ironing
board into a position of approx.
45°.
The ironing board remains in this
position by itself.
ĺ Use both hands to pull the iro-
ning board upwards into a horizontal position until this audibly
clicks into place on both sides
of the tower.
ĺ Ensure the ironing board has lo-
cked into place on both sides of
the tower.
The height adjustment only works
if both sides of the appliance have
locked into place.
2. Height adjustment
The steam ironing system can be adjusted to suit your
personal preference.
ĺ Use one of the rotary dials
located on the side of the tower handle. Turn the dial in
thedirection and hold the
dial in position.
ĺ At the same time, pull the
handle on the tower upwards
with the other hand up or press
the handle down.
Do not push down on the ironing board while adjusting the height.
ĺ When you have reached your desired working height,
release the rotary dial.
The rotary dial will spring back into the center position.
The ironing board remains in this position by itself.
This is how the steam ironing system is set
up.
3. Connection
ĺ Open the (lower) storage com-
partment by swinging the lid
downwards.
ĺ Remove the power cord from the
compartment.
ĺ Insert the power plug into a sui-
table grounded outlet.
ĺ Guide the power cord through
the groove in the cover.
ĺ Close the storage compartment.
ĺ Open the lid of the (upper) stora-
ge compartment on the tower.
ĺ Take out the iron and the steam
hose holder and close the storage compartment.
ĺ Plug the steam hose holder into
one of the sockets provided.
ĺ Plug the steam hose into the
steam connection on the tower to
connect the iron.
ĺ Guide the steam hose on the
rubber ring into the steam hose
holder.
ĺ Always place the iron on the res-
ting surface before you start ironing and when you take a break
from ironing.
Switching on / filling the water container Ironing / Switching off Dismantling
Switching on the steam ironing system
ĺ Press the button on the control panel
on the tower.
The button is illuminated and the Welcome screen appears for several seconds in
the display.
The message"Pre-heating phase" then appears on the display. The steam ironing system
starts to heat up.
As soon as the steam ironing system is ready
and steam is available, the message "Ready"
will be displayed.
Filling the water container
Never attempt to use distilled water to fill the water container. This can cause the
steam ironing system to malfunction.
Do not use water from a water softener system.
Do not use condensate (e.g. from other appliances such as air conditioning units,
dryers).
Never use rainwater.
Do not use additives, (e.g. perfumes, ironing water, starch, carbon dioxide).
If the water container is empty or not installed in the tower, the message "Fill the water
container" is displayed.
ĺ Hold the water container by its handle.
ĺ Pull the handle downwards.
The water container is released from the retainer.
ĺ Pull the water container upwards and out.
ĺ Open the twist lock at the rear of the water container by turning
the lock to the left (counterclockwise).
ĺ Remove the twist lock.
ĺ Refill the water container with fresh tap water.
ĺ Close the twist lock by turning it to the right (clockwise) as far as it
will go.
ĺ Put the water container back into the tower.
The water container can be removed and refilled at any time (even
ASSEMBLY
during the ironing process).
Selecting the ironing temperature
ĺ Set the temperature selector to the required temperature setting.
Care label
(on the garment)
Low temperature
Ironing with steam for best results
(Material / Temperature setting)
With non-stick soleplate
Minimum iron, synthetics, appliqués,
prints, flocking, etc.
Ironing without steam
(Material / Temperature setting)
Minimum iron, synthetics
+
Medium temperature
High temperature
The temperature settings are indicated on the scale of the selector.
When selecting the temperature levels Silk/Wool and Linen/Cotton you can use steam
when ironing.
Switching off the steam ironing system
ĺ To switch off the steam ironing system, press the button on the control panel.
The illuminated button goes out.
Wool, silk
Linen, cotton
Do not iron
When putting the steam ironing system away:
ĺ Remove the plug from the socket.
ĺ Store the power cord in the (lower) compartment or hang it up on
the cord clip.
Dismantling the steam ironing system
To dismantle the steam ironing system, the ironing board must first be placed at its lowest working height.
ĺ Turn one of the rotary dials on the side of the tower handle as far
as it will go in the direction.
ĺ Hold the rotary dial in the position.
The height of the ironing board can now be adjusted.
ĺ Keep holding the rotary dial in the position and, simultaneous-
ly, use the handle of the tower to push the ironing board down as
far as possible.
Never push on the ironing board to push it down.
ĺ Release the rotary dial.
The rotary dial will spring back into the center position.
ĺ Turn one of the two rotary dials to the position as far as it will
go.
The ironing board is now unlocked.
ĺ Release the rotary dial.
The rotary dial will spring back into the center position.
ĺ Guide the ironing board downwards or allow it to slide down by
itself.
The ironing board remains in this position by itself.
ĺ Push the ironing board up by the tapered end until it is upright and
locks into position on the tower.
ĺ Push the protruding end of the X-frame onto the ironing board un-
til the frame locks into place.
M.-No. 10 462 481 / 02FashionMaster 4817 en-US,CA
fold herefold herefold herefold herefold herefold here
Loading...