Miele B 3847 Operating instructions

Operating instructions Steam ironing system
To avoid the risk of accidents or damage to the appliance, it is essential to read these instructions before it is installed and used for the first time.
en-AU,NZ M.-Nr. 10 675 001
Caring for the environment
Disposal of the packing material
The transport and protective packaging has been selected from materials which are environmentally friendly for disposal, and can normally be recycled.
Recycling the packaging reduces the use of raw materials in the manufacturing process and also reduces the amount of waste in landfill sites. Ensure that any plastic wrappings, bags etc. are disposed of safely and kept out of the reach of babies and young children. Danger of suffocation.
Disposing of your old appliance
Electrical and electronic appliances often contain valuable materials. They also contain specific materials, compounds and components, which were essential for their correct function and safety. These could be hazardous to human health and to the environment if disposed of with your domestic waste or if handled incorrectly. Please do not, therefore, dispose of your old appliance with your household waste.
Please dispose of it at your local community waste collection / recycling centre for electrical and electronic appliances. You are also responsible for deleting any personal data that may be stored on the appliance prior to disposal. Please ensure that your old appliance poses no risk to children while being stored prior to disposal.
2
Contents
Caring for the environment .................................................................................. 2
Warning and Safety instructions .........................................................................6
Guide to the appliance........................................................................................ 14
Transporting the appliance................................................................................. 17
Assembling .......................................................................................................... 18
Adjusting the height .............................................................................................. 19
Connecting........................................................................................................... 21
Connecting the mains connection cable............................................................... 21
Removing the iron and the steam hose holder ..................................................... 22
Connecting the steam hose .................................................................................. 22
Before using for the first time ............................................................................ 24
Determining water hardness ................................................................................. 24
Using the test strips .........................................................................................24
Before using for the first time................................................................................ 25
Switching on the steam ironing system ........................................................... 25
Language settings............................................................................................ 25
Setting the water hardness .............................................................................. 26
Set-up is now complete ................................................................................... 27
Switching on ........................................................................................................ 28
Switching on the steam ironing system ................................................................ 28
Filling the water container ..................................................................................... 29
Removing the water container ......................................................................... 29
Filling the water container ................................................................................ 29
Steam operation............................................................................................... 30
Water quality .................................................................................................... 30
Selecting the ironing temperature ......................................................................... 31
CoolDown function................................................................................................ 33
AutoOff function .................................................................................................... 33
Ironing .................................................................................................................. 34
Iron ........................................................................................................................ 34
Ironing with steam................................................................................................. 35
Ironing without steam............................................................................................ 36
Ironing with the non-stick soleplate ...................................................................... 36
Attaching the non-stick soleplate..................................................................... 36
Removing the non-stick soleplate.................................................................... 37
3
Contents
Active ironing board .............................................................................................. 37
Suction function ............................................................................................... 37
Inflation function............................................................................................... 37
Automatic switch on/off ................................................................................... 37
Memory function .............................................................................................. 38
Heated ironing surface ..................................................................................... 38
Steamer ................................................................................................................ 39
Connecting the steamer........................................................................................ 39
Using the steamer ................................................................................................. 41
Brush attachment.................................................................................................. 42
Connecting the brush attachment.................................................................... 42
Removing the brush attachment...................................................................... 42
Switching off ........................................................................................................ 43
Dismantling .......................................................................................................... 44
Setting the ironing board to its lowest working height.......................................... 44
Folding the ironing board ...................................................................................... 45
Disconnecting the steam hose.............................................................................. 46
Storing the iron...................................................................................................... 46
Storing the steamer............................................................................................... 46
Emptying the water container ............................................................................... 47
Storing the steam ironing system.......................................................................... 47
Cleaning and care ............................................................................................... 48
Automatic rinsing .................................................................................................. 48
Preparing for the rinsing process ..................................................................... 48
Emptying the residual water drawer................................................................. 48
Descaling............................................................................................................... 49
Descaling warning ............................................................................................ 50
Starting the descaling process early ................................................................ 51
Descaling process............................................................................................ 51
Cleaning the housing............................................................................................. 58
Cleaning the soleplate of the iron.......................................................................... 58
Cleaning or replacing the ironing board cover ...................................................... 59
4
Contents
Cleaning the water filter......................................................................................... 60
Disconnect the power supply........................................................................... 60
Removing the water container ......................................................................... 60
Removing the water filter cover........................................................................ 61
Removing the sealing ring................................................................................ 61
Pulling out the water filter................................................................................. 62
Cleaning the water filter.................................................................................... 62
Inserting the water filter.................................................................................... 63
Inserting the water container............................................................................ 64
Optional accessories ..........................................................................................65
Care products........................................................................................................ 65
Descaling tablets.............................................................................................. 65
Problem solving guide ........................................................................................66
Problem solving guide........................................................................................... 67
Display messages ................................................................................................. 73
After sales service............................................................................................... 77
Warranty ................................................................................................................ 77
Electrical connection ..........................................................................................78
Technical data...................................................................................................... 79
5

Warning and Safety instructions

This steam ironing system complies with current safety requirements. Inappropriate use can, however, lead to personal injury and damage to property.
To avoid the risk of accidents and damage to the steam ironing system, please read these instructions carefully before using it for the first time. They contain important information on its safety, installation, use and maintenance.
Keep these instructions in a safe place and ensure that new users are familiar with the content. Pass them on to any future owner.

Correct application

This steam ironing system is designed for domestic use and for
use in similar environments by guests in hotel or motel rooms, bed & breakfasts and other typical living quarters. This does not include common/shared facilities or commercial facilities within hotels, motels or bed & breakfasts.
The steam ironing system must only be used for ironing textiles
which are suitable for ironing according to the care label.
The steam ironing system is intended to be used only as
described in these operating instructions. Any other use is not permitted. Miele cannot be held liable for damage resulting from incorrect or improper use or operation.
This steam ironing system is not intended for use by persons
(including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning its use by a person responsible for their safety.
This steam ironing system is not suitable for outdoor use.
6
Warning and Safety instructions

Safety with children

Young children must be kept away from the steam ironing system.Older children may only use the steam ironing system when its
operation has been clearly explained to them and they are able to use it safely, recognising the dangers of misuse.
Cleaning work may only be carried out by older children under the
supervision of an adult.
Please supervise children in the vicinity of the steam ironing
system and do not let them play with it.
Make sure that young children cannot access the steam hose or
the power cable, either during use or while the steam ironing system is cooling down.
Miele recommends that only children over the age of 14 are allowed to operate the steam ironing system unsupervised.
Risk of suffocation!
Children may be able to wrap themselves in packing material or pull it over their heads with the risk of suffocation. Keep children away from any packing material.
7
Warning and Safety instructions

Technical safety

Before setting up the steam ironing system, inspect it visually for
any external damage. Never use a damaged steam ironing system. A damaged steam ironing system can be dangerous.
Check the iron of the steam ironing system for damage. Do not
use the iron if it has been dropped, if there is any visible damage or if it is leaking.
Before connecting the steam ironing system to the mains
electricity supply, make sure that the connection data on the data plate (voltage and frequency) matches the mains electricity supply.
Connection to a supply voltage other than the one quoted on the data plate can lead to functional faults and damage to the steam ironing system. If in doubt, contact a suitably qualified electrician.
Always remove and unwind the mains connection cable of the
steam ironing system completely from its (lower) storage compartment.
If the mains connection cable is damaged, it must be replaced
with a special cable of the same type (available from Miele). For safety reasons, this must only be fitted by a Miele service technician.
Do not use the steam ironing system if the ironing board cover is
damaged.
A damaged ironing board cover could be dangerous.
Do not use the steam ironing system without an ironing board cover.
The ironing board cover must be replaced with an original Miele cover.
8
Warning and Safety instructions
The electrical safety of this steam ironing system can only be
guaranteed when continuity is complete between it and an effective earthing system which complies with current local and national safety regulations. It is most important that this basic safety requirement is present and regularly tested and, where there is any doubt, the household wiring system should be inspected by a qualified electrician. Miele cannot be held liable for the consequences of an inadequate earthing system (e.g. electric shock).
Do not connect the steam ironing system to the mains electricity
supply via a multi-socket unit or an extension lead. These do not guarantee the required safety of the appliance (e.g. danger of overheating).
This steam ironing system complies with all relevant safety
requirements. Unauthorised repairs could result in unforeseen dangers for the user, for which the manufacturer cannot accept liability. Repairs must only be undertaken by a Miele authorised service technician, otherwise any subsequent damage will not be covered by the warranty.
Faulty components must only be replaced by genuine Miele
original spare parts. Only when these parts are fitted can Miele guarantee the safety standards of the appliance.
9
Warning and Safety instructions
The steam ironing system must be isolated from the electricity
supply during installation, maintenance and repair work. The steam ironing system is only considered disconnected from the power supply if:
– the power plug of the steam ironing system is switched off at the
wall socket and unplugged, or
– it is switched off at the mains circuit breaker.
Do not damage, remove or bypass the safety features and control
elements of the steam ironing system.
Only operate the steam ironing system when all removable outer
panels are in place so that it is impossible to touch an electrical component or moving part.
The steam ironing system must not be operated in mobile
installations (e.g. on a ship).
10
Warning and Safety instructions

Correct use

Emitted steam, the iron soleplate together with the areas surrounding it on the iron, and the steamer jets are very hot.
Danger of burning!
Avoid direct contact.
The steam ironing system is not designed for commercial
purposes.
Do not use a pressure washer or water hose to clean the steam
ironing system.
Clean the steam ironing system only after it has cooled down.Danger of injury by crushing! Do not reach between moving parts
when assembling, dismantling or adjusting the height of the steam ironing system.
The steam ironing system must only be set up on a level surface
which has the appropriate load-bearing capacity. The steam ironing system must only be used in a horizontal position.
The steam ironing system must be assembled when ironing.
However, the steamer can be used when the ironing board is in the upright position.
Ensure that the power cable does not present a tripping hazard
when unwound.
Use caution when the appliance is heated. There is an acute risk
of burning if you come in contact with the soleplate of the iron or the steamer jets. The warning symbol “Hot surface”() on the iron indicates that it is hot.
Do not use solely demineralised water (e.g. distilled, battery
water) to fill the water container. This could cause the steam ironing system to malfunction.
11
Warning and Safety instructions
Always place the iron with its soleplate horizontally on the resting
surface of the steam ironing system. Ensure the steam function is switched off and the soleplate does not protrude over the edges. Do not place the iron anywhere else as this presents a fire hazard.
Danger of burning! If the iron remains on the resting surface for a
long period of time, the surface will become hot. Avoid direct contact with the resting surface.
Danger of burning! Never direct the steam or the steam jets of the
iron or steamer at people, animals or electrical appliances of any kind.
Danger of burning! Never point the steam at clothing while the
clothes are being worn! The clothing will intensify burning of the skin.
Switch off the steam ironing system before disconnecting the
mains connection cable.
Switch off at the wall socket and withdraw the plug from the
socket. Always pull by the plug to withdraw the plug from the socket.
Do not leave the steam ironing system unattended when it is
ready for use. Before you leave the steam ironing system, disconnect the steam ironing system from the mains and withdraw the plug from the mains socket.
Do not touch the mains connection cable or the steam hose with
the soleplate of the heated iron as this could result in damage.
While descaling the system, the iron or the steamer must not be
connected to the steam ironing system. The steam ironing system can be left unattended during this process.
The iron must not be stowed in its storage compartment when it is
connected. This could result in damage to the steam ironing system.
Do not use the residual water drawer to store accessories or
similar items. The residual water drawer should be used only to collect residual water.
12
Warning and Safety instructions
Do not insert any objects into the apertures on the steam ironing
system. If an aperture is blocked, do not use the system.
Do not hang items of laundry on the folded steam ironing system.
This may cause the steam ironing system to tip over due to the effect of leverage.
Avoid ironing across hard or sharp-edged items. These can leave
marks on the soleplate.
Do not store the steam ironing system near petrol, paraffin or
other highly flammable substances. Risk of fire and explosion!
Only use the steam ironing system inside buildings where the
ambient temperature is between 10°C and 40°C.
Freezing temperatures, excessive heat and humidity will adversely affect the functionality of the steam ironing system.
Do not store the steam ironing system in a room where there is a
risk of frost occurring. Frozen water in the water container, steam generator or steam hose will cause damage to the appliance.

Using accessories

Only use genuine Miele spare parts and accessories with this
appliance. If spare parts or accessories from other manufacturers are used, this will invalidate the warranty, and Miele cannot accept liability.
13

Guide to the appliance

a
Ironing board
b
Iron with steam hose
c
Steam hose holder
d
Handle
e
Water container
f
Tower
g
Residual water drawer
h
Top storage compartment
For the iron and the steam hose
holder.
* Supplied as standard with steam ironing system B3847. Available as optional accessory with steam ironing systems B3312 and B3826.
14
i
Ironing board X-frame
j
Iron resting area
k
Mains connection cable
l
Lower storage compartment For the mains connection cable, the steamer*, the non-stick soleplate, and the holder for the mains connection cable.
m
Castors
n
Release handle For setting up the steam ironing system
Guide to the appliance
Tower
a
Rotary dial for height adjustment and folding the appliance away
b
Iron resting area
c
Steam connection
Tower (top view) with open storage compartment (top)
d
Sockets for the steam hose holder
e
Control panel
f
Steam hose holder
g
Iron with steam hose
15
Guide to the appliance
Control panel on tower
h
On/Off button Switches the steam ironing system on or off.
i
Display Displays messages and instructions for the user.
j
Arrow button Lights up if additional options are provided or the display text exceeds the specified length of a line. Scrolls down the selection list to the next option or decreases a value.
k
Arrow button Lights up if additional options are provided or the display text exceeds the specified length of a line. Scrolls up the selection list to the next option or increases a value.
l
OK button Confirms the selection or the information in the display.
m
button Opens the settings menu. While in the settings menu, the language and the level of the water hardness can be adjusted, or the descaling process can be started.
Some of the messages in the display are more than one line long. Touch the or button to read them in full.
16
The steam ironing system is fitted with two castors. This allows the steam ironing system to be pulled across an even surface when folded up.
Hold the steam ironing system by its
handle and tip it gently towards you until the castors are free to roll.
This allows you to navigate easily across obstacles such as carpet edges, door thresholds or single steps.

Transporting the appliance

Two people are required for carrying
the steam ironing system up or down stairs. When doing so, ensure the ironing board is at the bottom.
When transporting the appliance, use
both handles on the underside of the appliance.
The steam ironing system must
only be transported or lifted when folded up.
Otherwise the locking mechanism of the ironing board could release and cause injury or damage.
17
*
click!
click!
I N S T A L L A T I O N *

Assembling

Move the steam ironing system to its
set-up location.
Use one hand to pull the release
mechanism upwards.
This releases the locking mechanism of the ironing board and the X-frame folds down.
Use both hands to pull the ironing
board upwards into a horizontal position until it audibly clicks into place on both sides of the tower.
Hold onto the release mechanism
and guide the ironing board into a position of approx. 45°.
The ironing board will remain in this position by itself.
18
Ensure the ironing board has locked
into place on both sides of the tower.
The height adjustment only works if both sides of the appliance have locked into place.
* I N S T A L L A T I O N *
The steam ironing system is now assembled. This is its lowest working position of approx. 83cm high.
Assembling

Adjusting the height

The steam ironing system can be adjusted to your preferred working height. The maximum working height is 102cm.
When adjusting the height, ensure the mains connection cable does not become trapped in the mechanism.
Using one of the rotary dials located
on the side of the tower handle, turn the dial in the direction and hold the dial in position.
19
* I N S T A L L A T I O N *
Assembling
At the same time, pull the handle on
the tower upwards with the other hand or press the handle down.
Do not push down on the ironing board while adjusting the height!
Always use the handle on the tower to do this.
When you have reached your desired
working height, release the rotary dial.
The rotary dial will spring back into the centre position. The ironing board will remain at the adjusted height.
For additional stability, the ironing board locks into place under extra pressure with an audible click. Now the working height you selected is twice as secure.
Useful tip: Adjust your working position to approx. hip height for optimum comfort.
20
* I N S T A L L A T I O N *

Connecting

Connecting the mains connection cable

The steam ironing system is designed for connection to a properly installed earthed socket for AC220-240V, 50-60Hz.
Open the (lower) storage
compartment by swinging the lid downwards.
Insert the plug into a suitable earthed
socket (see “Electrical connection”).
Guide the mains connection cable
through the slot in the lid.
Close the (lower) storage
compartment.
When closing the compartment, ensure the mains connection cable does not become trapped between the lid and the housing or between the castor and the tower.
Remove the mains connection cable
from the (lower) storage compartment.
21
* I N S T A L L A T I O N *
Connecting

Removing the iron and the steam hose holder

Open the lid of the (top) storage
compartment on the tower.
Take out the iron and the steam hose
holder.
Close the storage compartment lid.
The steam ironing system is suitable for right-handed or left-handed people. Operation is optimised for both sides.

Connecting the steam hose

Open the steam connection socket
by pulling it upwards.
Pull back the sliding switch on the
steam hose plug.
Plug the steam hose holder into one
of the sockets provided.
Useful tip: Use the socket on the side on which you are ironing.
22
Insert the plug into the steam
connection socket.
Release the sliding switch on the plug
when it is locked into the steam connection socket.
The iron is now connected to the steam connection socket.
* I N S T A L L A T I O N *
Slot the rubber ring on the steam
hose into the steam hose holder.
Ensure the steam hose is secure and is not twisted.
Connecting
Do not place the iron in an
upright position! It can easily tip over or fall to the
floor. Always place the iron onto the iron
resting area with its soleplate down.
If the iron remains on the resting
area for any length of time, the surface will become hot.
Avoid direct contact with the iron resting area.
Only touch the handle.
Before turning off the iron, and before placing the iron down, make sure you switch off the continuous steam function.
If the continuous steam function is not switched off, the following message will appear in the display Release stm. button.
Unlock the button by pushing the sliding switch on the iron forwards (see “Ironing”).
To avoid damage or discolouration to
the ironing board cover, always place the iron on the iron rest before you start ironing and during pauses in ironing.
Condensation can form on the iron resting area. This does not affect the functioning of the steam ironing system.
23

Before using for the first time

Before using the steam ironing
system for the first time, remove all packaging (e.g. the protective film from the tower).

Determining water hardness

In order for the steam ironing system to function properly and to display a message prompting you to descale it at the correct time, it is important to set the steam ironing system to the hardness of your local water supply.
The water hardness level indicates how much calcium is dissolved in the water. The higher the calcium content, the harder the water, and the harder the water, the more often the steam ironing system will need to be descaled.
Your local water supplier can inform you of the water hardness level in your area. This information can also be found online on the website of the water supply company.
As an alternative, you can also determine the approximate water hardness by using the test strips supplied.

Using the test strips

Dip the test strip in the water for
approx. 1second.
Remove the test strip from the water
and shake the water off the test strip.
After approx. 1minute, and based on the colouration, you will be able to read the water hardness from the table below:
Hardness range on the test strip
Test strips Water hardness
4 green zones < 0.5 mmol/l
1 red zone > 0.7 mmol/l
2 red zones > 1.3 mmol/l
3 red zones > 2.5 mmol/l
4 red zones > 3.8 mmol/l
Useful tip: It is useful to know your water hardness so that you can provide the service technician with this information in the event of any service calls. Please note your water hardness
level here: .................................. mmol/l
24

Before using for the first time

Willkommen
english (GB)
english (AU)
Before using for the first time
The following steps must be carried
out before using the appliance for the first time:

Switching on the steam ironing system

Press the button on the control
panel on the tower.
The Welcome screen appears for a few seconds in the display. The display will then guide you through the following settings:

Language settings

Use the or arrow buttons to
select your preferred language.
Press the OKbutton to confirm your
selection.
The language settings can be changed at any time via the settings menu ( button, menu option
Language ).
25
Before using for the first time
Set water
Level 7
Level 10

Setting the water hardness

Before the water hardness can be set, the display message Set water
hardness ... must first be confirmed by
pressing the OK button.
The steam ironing system gives you the option to set the water hardness to one of 10 settings.
Use the following table to determine the water hardness level that must be set for your steam ironing system:
°dH mmol/l °f Setting
1-4 0.2 - 0.7 2-7
5-7 0.9 - 1.3 9-13
8-11 1.4 - 2.0 14-20
12-15 2.2 - 2.7 22-27
16-20 2.9 - 3.6 29-36
21-25 3.8 - 4.5 38-45
26-30 4.7 - 5.4 47-54
31-36 5.6 - 6.5 56-65
37-45 6.7 - 8.1 67-81
46-70 8.3 - 12.6 83-126
Note: If the level in your area falls between water hardness settings in the table, e.g. 0.8, set your water hardness to the next highest level.
Level 1 Level 2 Level 3 Level 4 Level 5 Level 6 Level 7 Level 8 Level 9
Level 10
Use the or arrow button on the
control panel to set the water hardness level for your household.
Useful tip: If the water hardness fluctuates (e.g. 37- 50°dH/6.7­9.0mmol/l), always set the highest value (in this example 50°dH/9.0mmol/ l = Level 10).
Make sure the correct water hardness level is set.
An incorrect setting will invalidate all warranty claims.
Confirm your selection by pressing
the OKbutton.
The steam ironing system is now set for the specified water hardness.
The water hardness level can be changed at any time via the settings menu (button, option
Water hardness).
26

Set-up is now complete

This completes the settings for using the appliance for the first time. The message Initial set-up complete will appear in the display. Confirm this message by pressing the OK button.
The steam ironing system will normally run a rinse cycle automatically after it has been set up for use.
The steam ironing system can then be switched off or you can continue using it.
When using the appliance for the first time, a slight odour may be noticeable during the heating-up phase. This will dissipate with further use.
During operation of the steam ironing system, pumping, boiling and knocking noises may be heard. These are normal noises and do not indicate a malfunction.
Before using for the first time
27

Switching on

Switching on the steam ironing system

Press the button on the control
panel of the tower to switch on the steam ironing system.
The button lights up and the Welcome screen appears for several seconds in the display.
If the iron was not connected to the steam connection before switching it on, the message  is displayed. In this case, the steam hose must be attached to the steam connection (see “Connecting”).
If the steam button on the iron is locked when the steam ironing system is switched on, Release stm. button will appear in the display. If this is the case, first unlock the steam button by pushing the slider on the iron forwards (see “Ironing”).
Depending on the operating duration, immediately after switching the steam ironing system on, the automatic rinse function can be started (see “Automatic rinsing”) or you may be prompted to start the descaling process (see “Descaling”).
The steam ironing system is not available for ironing while the rinse or descaling process is running.
The message Heating-up phase then appears in the display. The steam ironing system starts to heat up. During the heating-up phase, some steam may be discharged from the iron.
As soon as the steam ironing system is ready and steam is available, the message Ready for use will be displayed.
28
Switching on

Filling the water container

If the water container is empty or not fitted in the tower, the message Fill
water cont. will appear in the display.

Removing the water container

Hold the water container by its
handle.
Pull the handle downwards.
The water container will release from the retainer.
Pull the water container upwards and
out.
When removing the water container, you may notice some water dripping while the water container valves are closing.
Useful tip: The dripping can be prevented by removing the water container slowly.

Filling the water container

Open the screw cap at the rear of the
water container by turning the cap anti-clockwise.
Remove the screw cap.Fill the container with fresh tap water
(water temperature approx. 15­35°C).
Useful tip: By placing the water container in the horizontal position, the water container can also be filled under very low taps.
Replace the screw cap on the water
container.
Close the screw cap by turning it
clockwise as far as it will go.
Fit the water container back in the
tower.
The water container can be removed and refilled at any time (even during the ironing process). The amount of water required will depend on how much steam is required.
29
Switching on
Ready for use

Steam operation

After inserting the water container, wait until the steam ironing system is ready to use steam. This is indicated by the Ready for use message in the display.
If the water container is refilled during the ironing process, the steam generator may have to reheat.
Useful tip: If you fill the water container as soon as the Fill water cont. message is displayed and the container is inserted into the tower there is no delay.
The steam ironing system is not active whilst the message Fill water cont. is shown in the display. However, you may continue to use the iron.
Useful tip: You can save energy by ironing dry and without steam. To do this, remove the water container. In this case, the steam generator will not be heated. As a result, the inflation and suction function of the ironing board is not available (see “Active ironing board”).

Water quality

Use only fresh tap water.Water prepared using commercially
available water filters may also be used.
For water hardness of more than 14°dH / 2.5mmol/l, you can use tap water mixed at a 1:1 ratio with distilled water. This halves the water hardness. Set the halved water hardness to the corresponding level on the steam ironing system (see “Setting the water hardness”).
If your tap water has a water hardness of 60°dH / 10.8mmol/l, the mixing ratio of 1:1 with distilled water results in a water hardness of 30°dH / 5.4mmol/l. The water hardness level that must be set on your steam ironing system must now be Level 7.
Never use solely demineralised (distilled) water to fill the water container.
This may cause the steam ironing system to malfunction.
Do not use water from a water softener system.
Do not use condensate (e.g. from other appliances such as air conditioning units or dryers).
Never use rainwater. Do not use additives in the water,
(e.g. perfumes, ironing water, starch, carbon dioxide).
30
Switching on

Selecting the ironing temperature

Use the temperature selector on the iron to set the ironing temperature.
With temperature level the soleplate temperature is too low for ironing with steam. If you use this temperature level, do not use the steam button.
If you do, water will escape from the steam jets.
Useful tip: Sort your laundry according to the heat sensitivity of the fabric. This allows you to iron faster: First, iron your laundry that is made of heat-sensitive fabric (e.g. synthetics) at temperature level . Then, iron all laundry made of wool or silk, using temperature level . Finally, iron all laundry made of cotton and linen, using temperature level .
Set the temperature selector to the
required temperature setting.
The indicator light on the temperature selector will light up yellow whilst the iron is heating up. It will go out once the set temperature has been reached.
The iron is then ready for use.
The temperature settings are indicated by dots around the selector. These dots correspond to the international care symbols used for ironing.
At temperature levels  and  you can use steam when ironing.
31
Switching on
Care label
(on the garment)
Low temperature
Medium temperature
High temperature
Do not iron
Ironing with steam for best
results
(Material / Temperature setting)
With non-stick soleplate
(see “Ironing with the non-stick soleplate”)
Minimum iron, synthetics, appliqués, prints, flocking, etc.
Woollens, silks
Cottons, linens
Ironing without steam
(Material / Temperature setting)
Minimum iron, synthetics
32
Switching on
Iron switched off

CoolDown function

The heating of the iron switches off automatically if the iron is not moved for longer than 3minutes. The message  appears in the display to indicate that the heating has switched off. After a certain time, steam is no longer available. The message Release stm.
button appears when the steam button
is locked. In this case, unlock the steam button by pushing the slider on the iron forwards (see “Ironing”).
The soleplate is still hot
immediately after the heating has been switched off!
Avoid direct contact.
Do not leave the steam ironing
system unattended with the iron or steamer connected!
Always switch off at the wall socket and withdraw the plug before leaving the steam ironing system unattended.

AutoOff function

If the iron or the steamer is not used for approx. 25minutes, the entire steam ironing system switches off automatically.
The steam ironing system is switched on again by pressing the button on the control panel.
As soon as the iron is moved, or the steam button has been released, the iron will start heating up again automatically. The time taken for the steam to be available again depends on the length of time the heating was switched off.
When the steam ironing system is ready and steam is available, the message Ready for use will be shown in the display on the tower.
33

Ironing

Iron

Depending on the model, your steam ironing system has one of the following irons:
Steam ironing system B3312:
a
Steam button
b
Sliding switch for continuous steam
c
Suction function button
d
Inflation function button
Steam ironing system B3826/B3847:
a
Steam button
b
Sliding switch for continuous steam
c
Power level button
d
Inflation/Suction function button
Irons supplied with previous Miele steam ironing systems (B1xxx/B2xxx) cannot be used with this appliance.
34
Ironing

Ironing with steam

The steam system is ready for use when Ready for use appears in the display. The burst of steam is controlled by the button on the iron.
When the button is pressed, the fan on the underside of the ironing board starts automatically.
When the button is released, the fan will also stop automatically after a brief time delay.
When using the steam function for a long time, make sure the room is well ventilated, as high air humidity can develop.

Using short bursts of steam

Briefly press the button and
release it again.

Using continuous steam

Press the button and at the same
time pull the sliding switch back. Release the button again. While the sliding switch is pulled
back, the button remains in a locked position.
Steam is now emitted continuously.

Stopping the continuous steam function

Push the sliding switch forwards. This will unlock the button again and
the steam burst function is ended.
The continuous emission of steam must have stopped before the iron is put back on the resting surface.
If the steam button was not unlocked before placing the iron down, steam will stop being produced after approx. 3minutes and Release
stm. button will appear in the display.
When turning off the iron, unlock the button by pushing the sliding switch forwards.

Filling the water container

Fill the water container when the
message Fill water cont. appears in the display (see “Filling the water container”).
When using the steam function for a long time during ironing, condensation can build up in the ironing board.
Sensitive floors can be damaged by droplets of water.
If you notice condensate underneath the ironing board, use a cloth to wipe it up.
Useful tip: If you take a break from ironing, condensate may collect in the steam hose. When the button is pressed, the condensate is expelled from the hose. To avoid damp spots on your clothes, do not direct the first burst of steam onto the garment after a break from ironing.
35
Ironing

Ironing without steam

Remove the water container from the
steam ironing system if you want to
iron without steam.
The steam generator will not heat up, thus saving you electricity.

Ironing with the non-stick soleplate

There is a non-stick soleplate in the (lower) compartment. Simply clip the soleplate onto the iron.
With the non-stick soleplate you can iron appliqués, prints, flocking etc. There is no need to turn the garment inside out. This soleplate also reduces or eliminates the formation of shiny patches on dark textiles.
Always try it first on an inconspicuous part of the fabric.
The iron soleplate gets very hot
during use. Avoid direct contact.

Attaching the non-stick soleplate

Place the tip of the iron inside the
non-stick soleplate.
Pull back the tab which is located at
the back of the non-stick soleplate.
Hold the tab in this position.Push the iron completely onto the
non-stick soleplate.
Release the tab again.
The non-stick soleplate is now secured onto the iron.
36
Before you start ironing, let the non-
stick soleplate heat up for approx. 1minute until it has reached the ironing temperature.
The iron is now ready for use.
Ironing

Removing the non-stick soleplate

Hold the iron by the handle.
The non-stick soleplate is still
very hot after ironing. Avoid direct contact. Only touch the tab of the non-stick
soleplate.
Pull back the tab at the back of the
non-stick soleplate. Remove the iron from the non-stick
soleplate. Only store the non-stick soleplate in
the storage compartment (lower) after
the soleplate has cooled down.

Active ironing board

The steam ironing system uses a fan that sucks away the steam or uses the inflation function to inflate the ironing board for optimum positioning while ironing garments.
The , or , buttons on the iron control the fan in the ironing board.

Suction function

The suction function ensures optimum steam penetration of the fabric. At the same time, the suction avoids the formation of condensation on the ironing board. The suction function also holds the garment in place and ensures it does not shift on the ironing board.

Inflation function

The inflation function forms a cushion of air between the fabric and the ironing board. This helps prevent seams being pressed into the garment. The inflation function allows you to iron without flattening the fabric.
Useful tip: The inflation function also assists with ironing ruffles and sequins.

Automatic switch on/off

The automatic switch on/off feature ensures that the fan starts at exactly the right moment. If the steam function is being used, the fan starts automatically.
If steam is no longer needed, the fan will stop after a short run-on time.
37
Ironing

Memory function

The memory function saves the fan direction and the power setting used last with your steam ironing system. When you use the appliance the next time, you do not need to set it again.

Heated ironing surface

When the iron is connected and the steam ironing system is switched on, the surface of the ironing board will heat up automatically. This function reduces the formation of condensation on the ironing board.
If the steamer is connected to the steam ironing system, the surface of the ironing board will not be heated.
Fan control for the B3312:
Fan control for the B3826/B3847:

Activating the inflation and suction function

Press the button to switch between the inflation function and the suction function. Use the button to activate the function.

Setting the power level

When using the button, you can switch between both fan power levels. Each press of the button switches between the following power levels:
The button activates the inflation function.
The button activates the suction function.
38
– Level1 = 1 fan active
– Level2 = 2 fans active

Steamer

The B3847 steam ironing system is equipped with a steamer in addition to the iron. The steamer is available as an optional accessory for the B3312 and B3826 steam ironing systems.
The steamer makes ironing hanging garments easier, e.g. dresses and jackets. It comes with a removable brush attachment for lifting the fibres.

Connecting the steamer

You can also plug the steamer into the steam connection socket of the ironing system as an alternative to the iron.

Disconnecting the iron from the steam connection socket

The iron soleplate is still very hot
after use! Avoid direct contact. Place the iron on its resting surface
and let it cool down completely before you store it away.
Do not pull on the steam hose. Always pull on the plug at the end of
the steam hose when disconnecting it from the steam connection socket.
The steamer weighs less than the iron and also does not have a hot soleplate, therefore eliminating the risk of shiny patches if it accidentally comes into contact with the fabric.
The steamer can also be used when the appliance is folded up.
The steamer supplied with earlier steam ironing systems (B1xxx/B2xxx) cannot be used with this appliance.
Pull back the sliding switch located
on the side of the steam hose plug.
Hold back the sliding switch.Withdraw the plug from the steam
connection socket.
39
Steamer
Now you can connect the steamer to the steam connection socket.

Attaching the steamer to the steam connection socket

Pull back the sliding switch located
on the side of the steam hose plug. Insert the steam hose plug into the
steam connection socket on the
tower.
You can plug the iron into the steam connection socket as an alternative to the steamer at any time.
You do not need to switch off the steam ironing system to do this.
After switching between the iron and the steamer, there is a short interval before the steam is ready. This ensures that sufficient steam is available.
The steamer is ready when the message Ready for use appears in the display.
Release the sliding switch when the
plug has locked into place in the
steam connection socket.
The steamer is now attached to the steam connection socket.
40
Steamer

Using the steamer

Danger of burning due to hot
steam! Never direct the steam or the steam
jets at people, animals or electrical appliances of any kind.
Never point the steam at clothing while the clothes are being worn. The clothing will intensify burning of the skin.

Using short bursts of steam

Briefly press the button.Then release the button.

Using continuous steam

Press the button.Keep the button pressed in.

Stopping the continuous steam function

Release the button.
If you take a break from steaming, condensate may collect in the steam hose. Press the button to expel the condensate from the hose.
The optimum distance between the steamer and the fabric depends on the sensitivity of the fabric and can vary from one fabric to another.
Always try it first on an inconspicuous part of the fabric.
The emission of steam is controlled by thebutton on the steamer.
Useful tip: Always steam the fabric in the direction of the fibres.
41
Steamer

Brush attachment

The steamer is equipped with a brush attachment which can be clipped on. The brush attachment helps to raise garment fibres.
You can hold the steamer directly onto the fabric while the brush attachment is in place.
Always try it first on an inconspicuous part of the fabric.

Connecting the brush attachment

Guide the brush attachment into the
notches on the opposite side.
Press the brush attachment against
the steamer until the lugs snap into the notches.
The brush attachment is now connected to the steamer and can be used.
Hold the brush attachment in front of
the steamer so that the lugs on one
side fit into the notches on the
steamer. Press the side of the brush
attachment against the steamer until
the lugs snap into place.
42

Removing the brush attachment

To remove the brush attachment, pull
it off the steamer by the raised section.
To switch off the steam ironing
system, press the button on the
control panel. The light in the button goes out.
The steam ironing system is now switched off. The last selected fan settings are saved and are available for the next time you switch on the appliance.

Switching off

Lower storage compartment
Place the iron on the resting surface
until it has cooled down.
The steam ironing system can be dismantled while the iron is cooling down (see “Dismantling”).
Switch off at the wall socket and
remove the plug.
Clip for the mains connection cable
Store the mains connection cable in
the (lower) compartment or hang it up on the cable clip.
The cable clip can be found in the (lower) compartment and can be pushed into one of the sockets for the steam hose holder.
43

Dismantling

Setting the ironing board to its lowest working height

To dismantle the steam ironing system, the ironing board must first be set to its lowest working height. Make sure you do not trap the mains connection cable in the system. Ensure the residual water drawer is completely emptied, pushed in and clicked into place.
Keep holding the rotary dial in the
position and, simultaneously, use
the handle on the tower to push the ironing board down as far as possible.
Never push on the ironing board to push it down.
Use only the handle on the tower to push the ironing board down.
Turn one of the rotary dials on the
side of the tower handle as far as it
will go in the direction. Hold the rotary dial in the position.
The height of the ironing board can now be adjusted.
44
Release the rotary dial.
The rotary dial will spring back into the centre position.
The ironing board is now at its lowest working height and can be folded away.
After withdrawing the plug, drops of water may escape from the steam hose.

Folding the ironing board

Turn one of the two rotary dials as far
as it will go towards the position.
The ironing board is now unlocked. Release the rotary dial.
The rotary dial will spring back into the centre position.
Dismantling
Push the ironing board up by the
tapered end until it is upright and locks into position on the tower.
Guide the ironing board downwards
or allow it to slide down by itself.
The ironing board will remain in this position by itself.
Push the protruding end of the X-
frame onto the ironing board until the frame locks into place.
45
Dismantling

Disconnecting the steam hose

Do not pull on the steam hose. Hold the plug at the end of the steam
hose. The plug may still be warm immediately after using the system.
Pull back the sliding switch located
on the side of the steam hose plug.
Hold back the sliding switch.Withdraw the plug from the steam
connection socket.

Storing the iron

The iron soleplate is still very hot
after use! Avoid direct contact. Allow the iron to cool down after use. Do not stow the iron away while it is
still attached to the hose.
Place the iron on the resting surface
on the tower and let the iron cool down.
When cool, store the iron and the
steam hose holder in the (top) storage compartment.

Storing the steamer

Never put the steamer away while it is still connected to the steam connection socket.
After withdrawing the plug, drops of water may escape from the steam hose.
46
Store the steamer in the (lower)
storage compartment.
Dismantling

Emptying the water container

Empty the water container if the steam ironing system is not going to be used for a long period of time.
Remove the water container (see
“Filling the water container”). Make sure the water container is
completely emptied.

Storing the steam ironing system

Take the steam ironing system to its
storage place.
Do not store the steam ironing system in a room where temperatures below freezing may occur.
Frozen water can cause damage to the water container, steam generator and steam hose.
47

Cleaning and care

Automatic rinsing

The automatic rinse function clears the steam generator of mineral deposits from the evaporated water.
After approx. 3litres of water have been passed through the system, the rinse process will start automatically the next time the steam ironing system is switched on.
The rinsing process takes several minutes. Steam escapes and splashing noises can be heard. At the same time the message Appliance rinsing will be shown in the display on the tower.
The iron cannot be used while the rinsing process is in progress.
The steam ironing system can only be used again once the automatic rinsing process is completed.

Preparing for the rinsing process

Set the steam ironing system to its
highest working position to enable
the residual water drawer to be
removed later on (see “Assembling -
Adjusting the height”). If the message Fill water cont.
appears in the display, fill the water
container (see “Filling the water
container”).

Emptying the residual water drawer

After the rinsing process has finished, the residual water drawer must be emptied. The message Empty
drawer will appear in the display on the
control panel when the residual water drawer needs to be emptied. The residual water drawer can only be removed from the tower when the steam ironing system is set at its highest working level.
Only remove the residual water
drawer from the tower when prompted to do so by the message Empty drawer in the display.
The residual water drawer may still be warm after the rinsing process.
Empty the residual water drawer.
48
As long as the residual water drawer is not fitted in the tower, the display will show the following message Fit
drawer.
Clean and dry the residual water
drawer.
Cleaning and care
The residual water drawer is dishwasher-safe or can be washed by hand using warm water and a little washing-up liquid.
Make sure the metal discs (contacts) at the top of the residual water drawer are clean and dry. These metal discs send a signal to the steam ironing system when the residual water drawer is full or if it is fitted in the tower.
The discs will not function correctly if they are dirty or damp.
Slide the residual water drawer back
into the tower until it clicks into place.
Steam cannot be produced until the empty residual water drawer is replaced in the tower. Steam is only available again when the message Ready for use appears in the display.

Descaling

The steam ironing system must be descaled regularly to ensure that it functions correctly. The steam ironing system has an automatic descaling function to assist you.
The interval for descaling depends on the water hardness level set. Descaling is required more frequently with hard water than with soft water.
We recommend using the Miele descaling tablets. These have been specially developed for use with Miele appliances to optimise the descaling process. Your appliance is supplied with one pack of Miele descaling tablets.
Other descaling agents, which contain other acids besides citric acid and/or other undesirable substances, such as chlorides, could damage the steam ironing system. Moreover, the required descaling effect cannot be guaranteed.
You will need 1descaling tablet to descale the machine.
Miele descaling tablets are available to order from Miele (see “Optional accessories”).
The iron or steamer must not be connected during descaling of the steam ironing system.
The steam ironing system can be left unattended during descaling, provided that the iron or steamer is not connected.
49
Cleaning and care

Descaling warning

Descale soon will appear in the display the next time you switch the steam ironing system on if there are only about 2hours of ironing available before the system needs descaling.
You can start the descaling process whilst the system is cold via the Settings menu (see “Starting the descaling process early”) or you can press the OK button to confirm the message in the display and continue ironing as normal. The symbol will continue to show in the display until descaling is carried out.
After the remaining operating hours have elapsed, the descaling process must be carried out before the steam ironing system can be used again.
You can also start the descaling process at a time that suits you (see “Starting the descaling process early”).
further 60minutes. For the rest of the descaling process, you can leave the steam ironing system unattended.
Useful tip: To optimise the descaling process, start the procedure while the system is still cold immediately after switching the steam ironing system on. This way, you will avoid a delay of up to 3hours that may be caused by the cooling phase.
You can interrupt the descaling process by switching the steam ironing system off with the button. When you switch the system back on, descaling will start again from the point where the process was interrupted.
The messages in the display will guide you through the descaling process. The entire descaling process takes approx. 90minutes.
Only proceed with stages of the process when prompted to do so by the appropriate message in the display. Once the descaling process has started, your presence is required after around 20minutes and again after a
50
Cleaning and care
Ready for use
Language 
Descale

Starting the descaling process early

When the steam ironing system is
switched on, press the button on
the control panel.
The settings menu will be displayed. Use the arrow buttons to select individual settings.
Use the or arrow buttons to
select the Descale option.

Descaling process

The following display messages will guide you through the entire descaling process. Only proceed with the required action if you are prompted to do so by the appropriate message in the display.
Detach hose
Remove the steam hose of the iron or
the steamer from the steam connection socket on the tower.
Confirm your choice by pressing the
OKbutton.
Select the Start descaling option.Confirm your choice by pressing the
OKbutton.
The descaling process will now start.
The iron or the steamer must not be attached to the steam connection socket at any time during the descaling process.
51
Cleaning and care
Fill water container to mark
Hold the water container by its
handle. Pull the handle downwards.
The water container will release from the retainer.
Pull the water container upwards and
out.
When removing the water container, you may notice some water dripping while the water container valves are closing.
Useful tip: The dripping can be prevented by removing the water container slowly.
After removing the water container, the message Add descaler will appear in the display.
Add descaler
Turn the screw cap at the back of the
water container anti-clockwise and remove the cap.
Level mark on the water container
Use fresh tap water to fill the water
container (water temperature approx. 15 to 35°C) to the level mark. It is important not to fill the water container with more or with less water.
Add 1 descaling tablet to the water
container.
Replace the screw cap on the water
container.
Turn the screw cap clockwise as far
as it will go.
The screw cap is now closed.
52
Add descaler
Press the OKbutton to display the
next step. The message Fit water container will
now appear in the display.
Cleaning and care
Fit water container
Fit the water container back in the
tower.
After about 10minutes (the time it takes for the descaling tablet to dissolve), the descaling process begins automatically. Messages in the display will tell you when to empty the residual water container or when to fill the water container.
If the water container becomes empty during descaling or if it is removed from the tower unprompted, the messageFit or
refill water container will appear.
During the descaling process, water is pumped into the steam generator at various times and is drained back again into the residual water drawer. Some steam will escape and splashing noises can be heard during this process.
53
Cleaning and care
Empty drawer
This message may be displayed after inserting the water container with the descaling tablet. If you do not see this message, you can skip the following steps and continue as soon as you seePre-rinse in the display.
Set the steam ironing system to its
highest working position in order to
remove the residual water drawer
(see “Assembling - Adjusting the
height”).
Pre-rinse
If the steam ironing system is still hot from the previous use, the cooling down phase will start first. This may take up to 3hours.
The pre-rinse phase then follows (duration approx. 20minutes). During this time, a portion of the descaling solution is pumped into the steam generator.
After the pre-rinse phase you will be prompted to carry out further actions. This will be shown for a few seconds before the pre-rinse phase starts and will be indicated by the message In
20 min. .
Remove the residual water drawer
from the tower.
The residual water drawer may still be warm after the rinsing process.
Empty the residual water drawer.
As long as the residual water drawer is not inserted into the tower, the display will show the following message Fit
drawer.
Fit drawer
Slide the residual water drawer back
into the tower until it clicks into place.
54
Cleaning and care
Rinse water container and fill to the mark
Remove the water container from the
tower.
As long as the water container is not fitted in the tower, the display will show the following message Fit water
container.
Open the screw cap.Rinse the water container thoroughly.
Make sure no residues of the
descaling tablet remain in the water
container. Fill the water container with fresh tap
water at least up to the level mark.
Close the screw cap.Fit the water container back in the
tower.
Empty drawer
Remove the residual water drawer
from the tower.
The message Fit drawer will appear in the display.
Empty the residual water drawer.Slide the residual water drawer back
into the tower until it clicks into place.
55
Cleaning and care
Descale
After an activation time of approx. 1hour, the descaling solution is drained from the steam generator into the residual water drawer.
The steam generator is then rinsed with water. This rinse cycle takes approx. 5minutes. Before starting, the
Rinsing (5 min.) message is displayed
for a few seconds.
During the rinsing cycle, the message
Rinsing is displayed.
Once the rinsing cycle is completed, the water is drained completely into the residual water drawer and the message
Empty drawer is displayed.
Empty drawer
Remove the residual water drawer
and empty it.
The message Fit drawer is now shown in the display.
Rinse the residual water drawer
thoroughly.
The residual water drawer is dishwasher-safe or can be washed by hand using warm water and a little washing-up liquid.
Dry the residual water drawer. Make
sure that the metal discs (contacts) at the top of the residual water drawer are clean and dry.
Slide the residual water drawer back
into the tower until it clicks into place.
The message Descaling finished will appear in the display.
Press the OK button.
56
The soleplate of the iron must then be rinsed.
Cleaning and care

Rinsing the soleplate

The iron must not be warm from previous use.
Let the iron cool down for at least 60minutes before rinsing the soleplate.
Make sure that the non-stick
soleplate has been removed from the
iron.
If the non-stick soleplate is still on the iron, remove it now (see “Ironing ­Removing the non-stick soleplate”).
Fill the water container with fresh tap
water (see “Filling the water
container”). Set the temperature selector on the
iron to “cold” so that the line on the
selector is pointing to the indicator
light.
system is ready and steam is available, the message Ready for use will be shown in the display.
Hold the iron over a washbasin or a
heat-resistant container. You can also use the residual water drawer from the steam ironing system. Be aware, though, that the drawer can only be taken out of the steam ironing system once the appliance is switched on.
During the rinsing process, hot
water and steam come out of the iron.
Danger of burning! Never direct the iron at people,
animals or electrical appliances of any kind.
Press the button on the iron for
around a minute and tilt the iron. Keep the tip of the iron pointing downward slightly.
Hot water and steam will come out of the iron and dislodge any deposits that have built up. As soon as there is only steam coming out, you can release the button.
Plug the steam hose of the iron into
the steam connection on the tower
(see “Connecting the steam hose”).
If the steam ironing system is switched off, switch it on now by pressing the button. When the steam ironing
57
Cleaning and care
Now set the temperature selector on
the iron to the highest temperature
setting.
The indicator light on the temperature selector will light up yellow whilst the iron is heating up.
Useful tip: During the heating-up phase, you can set down the iron on the designated surface on the steam ironing system.
As soon as the indicator light goes out, the rinsing process is complete.

Cleaning the housing

Before cleaning the housing,
switch off at the socket and withdraw the plug.
Depending on the level of soiling, use a dry or moist soft cloth to wipe the housing.
Do not use abrasive cleaning agents.

Cleaning the soleplate of the iron

The soleplate of the iron remains
hot after ironing. Danger of burning! Switch off at the wall socket and
withdraw the plug. Let the soleplate of the iron cool down before you start the cleaning process.
Remove drops of water and deposits
from the soleplate by moving the iron
over a soft, absorbent cotton cloth
while it is still hot. Press the steam
button briefly 2-3 times in the
process.
The descaling process is now complete. The steam ironing system can now be switched off or used.
58
Depending on the level of soiling, use
a dry or moist microfibre cloth to clean the iron soleplate.
Only use the microfibre cloth to clean the iron soleplate!
Cleaning and care
To avoid damaging the surface, do
not use the following for cleaning:
– abrasive cleaning agents, (e.g.
powder cleaners, cream cleaners, chrome polish, eraser sponges).
– hard, abrasive brushes or sponges,
(e.g. pot scourers), or sponges which have been previously used and still contain abrasive cleaning agents.
– pointed objects.

Cleaning or replacing the ironing board cover

If the ironing board cover is soiled, you can wash and dry it. If the ironing board cover is damaged, it must be replaced before using the steam ironing system again.
When removing the ironing board
cover, always ensure the steam ironing system is switched off and the plug is removed from the wall socket.
Wait until the ironing board has cooled down.
Pull the fastener of the ironing board
cover out of the cavity at the tapered end of the ironing board.
Undo the fastener on the ironing
board cover by pushing the small toothed wheel at the centre of the fastener outwards.
Remove the cover in the direction of
the tower.
The felt pad remains on the ironing board.
59
Cleaning and care
Wash and dry the ironing board cover
according to the care label or replace
the cover if it is damaged.
Never use the steam ironing system without the ironing board cover in place.
Put the dry or new cover onto the
ironing board from the tower end first
and draw it down towards the
tapered end of the ironing board. Use the cord to pull the cover taut.
Ensure the cover is secure. Secure the ironing board cover in
position by pushing the small toothed
wheel on the fastener to the middle. Push the fastener back into the cavity
at the tip of the ironing board.

Cleaning the water filter

The water filter prevents foreign objects in the water from entering the steam ironing system and causing damage.
The water filter can be cleaned if it is dirty or clogged. You will notice if the water filter is dirty since this will cause more frequent pumping noises from the water feed pump.

Disconnect the power supply

Switch off at the wall socket and
withdraw the plug before cleaning the water filter.

Removing the water container

60
Hold the water container by its
handle.
Pull the handle downwards.
The water container will release from the retainer.
Pull the water container upwards and
out.
Cleaning and care

Removing the water filter cover

Use a Phillips head screwdriver to
remove the screw of the water filter
cover. Pull the water filter cover upwards.
The water filter must be taken out of the right-hand socket for cleaning. There is a hook and a round tool at the sides of the water filter cover. Use these to remove the sealing ring from the socket and pull out the water filter.

Removing the sealing ring

Use the hook on the water filter cover
to pull the sealing ring up and out of the right-hand socket.
Please note that the top of the sealing ring looks different to the bottom of it. The top has a smooth surface all round and the bottom has a narrow ridge around it. After cleaning the water filter, make sure that the seal is replaced with the ridge facing downwards.
61
Cleaning and care

Pulling out the water filter

Push the round tool on the water filter
cover onto the water filter from
above.
The round tool will click into the water filter.
Pull the water filter out of the socket.

Cleaning the water filter

Detach the water filter from the round
tool.
Clean the water filter thoroughly
under running water.
62

Inserting the water filter

Position the water filter with the small
seal facing downwards. Press the water filter fully into the
right-hand socket. Then refit the seal in the right-hand
socket. The side with the ridge must
face downwards.
Cleaning and care
Use a Phillips head screwdriver to
tighten the screw.
Then refit the water filter cover over
both sockets.
63
Cleaning and care

Inserting the water container

Refit the water container in the
retainer in the tower.
The steam ironing system is now ready for operation again.
If the water filter is not inserted, the steam ironing system will not work.
The water filter must be replaced if it is worn or damaged. Replacement filters are available from Miele.
64

Optional accessories

Miele appliances are designed to achieve the best possible results and to provide uncompromising satisfaction for as long as possible. To achieve this, all factors must interact perfectly with one another. Therefore Miele offers a comprehensive range of accessories that harmonise with Miele appliances for optimum performance.
The following items are just a few examples from our broad range of products and are available to order from shop.miele.com.

Care products

The Miele care product range has been developed specially to clean your appliance thoroughly and gently.

Descaling tablets

Miele descaling tablets guarantee the best cleaning result when descaling your Miele steam ironing system.
One tablet is required for each descaling process.
65

Problem solving guide

With the help of the following notes minor faults in the performance of the appliance, some of which may result from incorrect operation, can be corrected without contacting Miele. This will save time and money as a call-out charge will apply to customer service visits where the problem could have been rectified as described in these operating instructions.
Repair work to electrical appliances should only be carried out by an
authorised Miele service technician. Repairs and other work by unqualified persons could be dangerous. Miele cannot be held liable for unauthorised work.
Some of the messages in the display are more than one line long. Touch the or button to read them in full.
66

Problem solving guide

Problem solving guide
Problem Possible cause and remedy
The steam ironing system cannot be switched on.
After an interruption to the power supply, the steam ironing system does not work any more.
The height of the ironing board cannot be adjusted.
The steam ironing system cannot be dismantled.
The steam ironing system does not have any power. Check that
– the plug is inserted into the wall socket and that
the socket is switched on.
– the circuit breaker has not tripped.
The steam ironing system is switched off. Use the button on the control panel to switch
the steam ironing system on.
If the power cut occurred during the automatic rinse, the cycle will be repeated when the steam ironing system is switched on again.
If the power cut occurred during descaling, the process will be resumed from the stage at which it was interrupted when the appliance is switched on again.
The ironing board is not locked into place on both sides of the tower.
Use both hands to pull the ironing board up and
into the horizontal position until the locking mechanism audibly clicks into place on both sides of the tower (see “Assembling”).
The steam ironing system is not in its lowest working position.
Adjust the steam ironing system to its lowest
working height (see “Dismantling”).
The residual water drawer is not inserted completely and is not locked in place.
Push the residual water drawer back into the tower
until it locks into place.
Then adjust the steam ironing system to its lowest
working height (see “Dismantling”).
67
Problem solving guide
Problem Possible cause and remedy
The ironing board cannot be set in the final position during assembly or dismantling.
The ironing board became dislodged from the latching mechanism when the board was not in its lowest position.
The resting surface of the iron remains hot after
ironing. Danger of burning! Switch off at the wall socket and withdraw the plug.
Let the iron and the resting surface cool down before removing the iron from the resting surface, and proceed with the following steps.
The iron does not heat up.
68
Press and hold the release button on the tower
().
At the same time, turn one of the rotary dials on
the side of the tower as far as it will go in the direction of and hold the dial in this position ().
Push the tower down as far as possible ().  Then let go of the rotary dial on the side and
subsequently release the unlocking button on the tower.
Now the ironing board can either be folded away or brought into its working position.
If the ironing board still will not lock into place,
contact Miele.
The steam ironing system is switched off. Use the button on the control panel to switch
the steam ironing system on.
The steam hose is not plugged in properly.
Problem solving guide
Problem Possible cause and remedy
Plug the steam hose into the steam connection
socket on the tower again (see “Connecting”).
The iron has not been used for some time. Move the iron or activate the steam button.
The steam button is locked. Unlock the steam button by pushing the sliding
switch on the iron forwards.
The temperature set on the temperature controller has already been reached.
Set the temperature controller to a higher
temperature, if necessary.
The steam ironing system is rinsing. Wait until the rinsing process has been completed
(see “Automatic rinsing”).
The display is indicating a malfunction. Rectify the indicated malfunction and proceed as
described on the following pages (see “Display messages”).
The steam ironing system is damaged. Call Miele.
The ironing board is not heated.
The temperature of the iron is always high.
Steam has not been used for a while. Press the steam button. This will activate the
ironing board's heating system.
The steamer is attached to the steam connection socket on the tower.
The ironing board does not heat up when the
steamer is connected.
The ironing board is not locked into place on both sides of the tower.
Ensure the ironing board locks into place on both
sides of the tower (see “Assembling”).
The steam ironing system is damaged. Call Miele.
There is a fault with the steam ironing system. Call Miele.
69
Problem solving guide
Problem Possible cause and remedy
The ironing board cover is damp.
Water is leaking from the steam ironing system at the height of the water container when it is being transported.
The fan on the ironing board is not running.
There is a fault with the steam ironing system. Remove the ironing board cover and allow it to
dry.
Put the dry ironing board cover back on (see
“Cleaning or replacing the ironing board cover”).
If the ironing board gets damp again, contact Miele.
The frequent removal and replacement of the water container may cause water droplets to collect in the area under the water container.
Use a cloth to dry the area underneath the water
container.
Steam was not used. The fan only runs when the steam function on the
iron is activated.
The appliance is not yet ready to produce steam. Wait until the message Ready for use is
displayed to indicate that steam is ready.
The water container is empty or not fitted. Fill the water container with fresh tap water and
insert it into the appliance.
The steamer is connected. The fan only runs when the iron is connected.
Connect the iron.
There is a fault with the steam ironing system. Call Miele.
70
Problem solving guide
Problem Possible cause and remedy
The steam function on the iron or the steamer is not working.
The steam ironing system is not connected to the wall socket.
Insert the plug into the socket correctly.Use the button on the control panel to switch
the steam ironing system on.
The iron or steamer is not connected. Attach the steam hose of the iron or the steamer to
the steam connection socket on the tower.
The water container is empty or not fitted.
Fill the water container with fresh water.Fit the water container in the tower.Wait until the message Ready for use is
displayed.
The appliance is not yet ready to produce steam. Wait until the message Ready for use is
displayed.
The display is indicating a malfunction. Rectify the indicated malfunction and proceed as
described on the following pages (see “Display messages”).
If there is still no steam, contact Miele.
71
Problem solving guide
Problem Possible cause and remedy
When using the steam button on the iron, drops of water or white deposits escape from the steam jets.
The selected temperature level on the iron is too low. Set the temperature selector to at least  (see
“Switching on - Selecting the ironing temperature”).
The iron has not yet reached the selected temperature.
Wait until the selected ironing temperature has
been reached (see “Switching on - Selecting the ironing temperature”).
During a longer ironing break, condensation has accumulated in the steam hose.
After a break in ironing, do not direct the first burst
of steam onto the garment.
Deposits have formed in the soleplate. Rinse the soleplate (see “Descaling process -
Rinsing the soleplate”).
72
Problem solving guide

Display messages

Message Possible cause and remedy
Drain valve closing When the steam ironing system was switched on,
the steam generator drain was open. The drain is closed automatically during this message.
Drain valve fault
Switch off/on
Memory fault
Switch off/on
Unplug at mains
The descaling or rinsing process has not been carried out properly.
Press the button to switch the steam ironing
system off and then back on again.
If the fault message continues to be displayed,
contact Miele.
There is a fault with the steam ironing system. Press the button to switch the steam ironing
system off and then back on again.
The steam ironing system must now be reset. Complete the steps required when using for the
first time (see “Before using for the first time”).
If the fault message continues to be displayed,
contact Miele.
Electronic fault. Switch off at the wall socket and withdraw the
plug.
Wait a while and then insert the plug back in the
socket and switch on.
Press the button to switch the steam ironing
system back on again.
The steam ironing system will try and rectify the fault itself.
If the fault message continues to be displayed,
switch off at the wall socket and withdraw the plug. Contact Miele.
73
Problem solving guide
Message Possible cause and remedy
Inlet fault, boiler
Switch off/on
Press. switch fault
Switch off/on
Boiler fault, warm
Switch off/on
There is a fault with the steam system. Press the button to switch the steam ironing
system off and then back on again.
After the cool-down phase, the steam ironing system will carry out a rinse and attempt to correct the fault itself. The cool-down phase can take up to 3hours.
Remove the residual water drawer if you are
prompted to do so by the appropriate message in the display.
Empty and dry the residual water drawer.Push the residual water drawer back in the tower
until it clicks into place.
There is a fault with the steam ironing system. If the fault message continues to be displayed,
contact Miele.
There is a fault with the steam system. Press the button to switch the steam ironing
system off and then back on again.
If the fault continues to be displayed, contact
Miele.
There is a fault with the steam ironing system. Press the button to switch the steam ironing
system off and then back on again.
If the fault continues to be displayed, contact
Miele.
The steam generator is soiled with water containing too much limescale or salt.
Start a descaling process (see “Starting the
descaling process early”). To avoid this problem in the future, the preset water hardness level can be set one level higher (e.g. from to , see “Setting the water hardness”).
If the fault continues to be displayed, contact
Miele.
74
Problem solving guide
Message Possible cause and remedy
Boiler fault, cold
Switch off/on
Release stm. button
Drain valve fault
Switch off/on
There is a fault with the steam ironing system. Press the button to switch the steam ironing
system off and then back on again.
If the fault continues to be displayed, contact
Miele.
The iron has switched itself off because it has not been used for a period of time and the steam button has locked.
Unlock the steam button by pushing the sliding
switch for continual steam on the iron forwards.
The residual water drawer has not been detected. Press the button to switch the steam ironing
system off and then back on again.
After switching the steam ironing system off and back on, the residual water drawer is not detected.
Press the button to switch the steam ironing
system off.
Clean and dry the metal discs (contacts) on the
residual water drawer.
Use the button to switch the steam ironing
system back on and follow the instructions shown in the display:
Remove the residual water drawer and fill it with
fresh tap water.
Fit the filled residual water drawer back in the
tower.
Remove the residual water drawer again when you
are prompted to do so and the appropriate messages are shown in the display.
Empty and dry the residual water drawer.Fit the empty residual water drawer back in the
tower.
The steam ironing system is now ready for operation and will continue to operate from the point reached before the fault was registered.
There is a fault with the steam ironing system. If the fault message continues to be displayed,
contact Miele.
75
Problem solving guide
Message Possible cause and remedy
Fault codes:
F38: ELP/EW/LNG F44 F45: LNG F47
There is an internal fault. Press the button to switch the steam ironing
system off and then back on again.
The steam ironing system will try and rectify the fault itself.
If the fault message continues to be displayed, contact Miele.
76

After sales service

After sales service

In the event of a fault which you cannot correct yourself, please contact Miele.
The contact details for Miele are given at the back of these instructions.
When contacting Miele please quote the model and serial number of your appliance. This information can be found on the data plate which is located on the tower behind the water container.

Warranty

The manufacturer's warranty for this appliance is 2 years.
For further information, please refer to your warranty booklet.
77
* I N S T A L L A T I O N *

Electrical connection

Before you connect the steam ironing system to the electricity supply, you must check the connection data (voltage and frequency) on the data plate and compare it with the data applicable to your local power supply.
This data must match, otherwise there is a risk of damage to the steam ironing system.
If in doubt, consult a suitably qualified electrician.
You will find the necessary connection data on the data plate, which is located in the tower behind the water container.
The steam ironing system is supplied with a cable and moulded plug ready for use with an alternating current of 50-60 Hz, 220-240 V. Connect the steam ironing system only to a properly installed and compliant earthed socket. All electrical work must be carried out by a suitably qualified and competent person in accordance with current local and national safety regulations.
Do not use a multi-socket adapter or an extension lead to connect the steam ironing system to the power supply.
Extension leads or multi-socket adapters do not guarantee the required safety of the steam ironing system (e.g. danger of overheating).
Do not connect the steam ironing system to an off-grid inverter. These devices are used for autonomous power supply, e.g. a solar power system.
Power surges could cause a safety cut-out. This could damage the electronics.
Do not use the steam ironing system with so-called “energy saving plugs”.
These reduce the energy supply to the appliance, which could generate excessive heat.
The fuse must have a rating of at least 10A. For extra safety, we recommend protecting the appliance with a 30mA residual current device (RCD).
The socket should be next to the appliance and easily accessible.
If the mains connection cable is faulty, it must only be replaced by a suitably qualified electrician.
78

Technical data

Dimensions, folded (HxWxD) 1280 x 470 x 370 mm
Assembled dimensions (HxWxD) 970 x 470 x 1480 mm
Weight 29 kg
Voltage See data plate
Total rated load See data plate
Fuse rating ≥ 10 A
Steam pressure for B3312
Steam pressure for B3826 and B3847
Steam quantity 100 g/min
Capacity of water container 1.25 l
Length of mains connection cable 2.50 m
Length of steam hose 1.80 m
Height of ironing board 830-1020 mm
Length of ironing board 1200 mm
Width of ironing board 400 mm
Product safety standard in accordance with AS/NZS60335-1,
AS/NZS60335-2-3
Test certificates awarded See data plate
3.5 bar
4.0 bar
79
808182
Miele Experience Centre and Head Office Melbourne:
1 Gilbert Park Drive Knoxfield, VIC 3180
Miele Experience Centre South Melbourne:
206-210 Coventry Street South Melbourne, VIC 3205
Miele Experience Centre and Office Sydney:
3 Skyline Place Frenchs Forest, NSW 2086
Miele Experience Centre and Office Brisbane:
Tenancy 4C, 63 Skyring Terrace Newstead, QLD 4006
Miele Experience Centre and Office Perth:
83-85 Sir Donald Bradman Drive Hilton, SA 5033
Miele Experience Centre and Office Adelaide:
Miele Australia Pty. Ltd. Miele New Zealand Limited
Level 2, 10 College Hill Freemans Bay, Auckland 1011
Miele Experience Centre Auckland:
8 College Hill Freemans Bay, Auckland 1011
Miele Global Headquarters Germany Miele & Cie. KG
Carl-Miele-Straße 29 33332 Gütersloh Federal Republic of Germany
Head Office:
IRD 98 463 631
ACN 005 635 398 ABN 96 005 635 398
Miele Experience Centre Gold Coast:
131 Ferry Road Southport, QLD 4215
Miele Experience Centre Wellington:
183 Featherston Street Wellington 6011
0800 464 353 (0800 4 MIELE)
www.miele.co.nz
205-207 Stirling Highway Claremont, WA 6010
1300 464 353 (1300 4 MIELE)
www.miele.com.au
FashionMaster
M.-Nr. 10 675 001 / 01en-AU,NZ
Loading...