Marantz SR5003 User Guide

AV Surround Receiver

SR5003

ENGLISHFRANÇAISESPAÑOL

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE

PARTS INSIDE REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL

The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufﬁ cient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE

TO RAIN OR MOISTURE.

NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

This Class B digital apparatus complies with Canadian ICES-003.

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

NOTE:

Changes or modiﬁ cations may cause this unit to fail to comply with Part 15 of the FCC Rules and may void the user's authority to operate the equipment.

Cet appareil numerique de la Classe B est conforme a la norme NMB-003 du Canada.

CAUTION:

TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG

TO WIDE SLOT, FULLY INSERT.

ATTENTION:

POUR EVITER LES CHOCS ELECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.

NOTE TO CATV SYSTEM INSTALLER:

This reminder is provided to call the CATV (Cable-TV) system installer’s attention to Section 820-40 of the NEC which provides guidelines for proper grounding and, in particular, speciﬁ es that the cable g round shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

DECLARATION OF CONFORMITY

This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

U.S. Responsible Party: Marantz America, Inc.

100 Corporate Drive, Mahwah, NJ, 07430, U.S.A. TEL: 201-7

Type of Product: Model:

62-6500

AV Surround Receiver SR5003

IMPORTANT SAFETY

INSTRUCTIONS

READ BEFORE OPERATING EQUIPMENT

This product was designed and manufactured to meet strict quality and safety standards . There are, however, some installation and operation precautions which you should be particularly aware of.

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacture's instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including ampliﬁ ers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not ﬁ t into your outlet, consult an electrician for replacement of the obsolete outlet.

Additional Safety Information!

• This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.

• Apparatus shall not be exposed to dripping or splashing and that no objects ﬁ lled with liquids, such as vases, shall be placed on the apparatus.

• When the switch is in the OFF position, the apparatus isn’t completely switched-off from the MAINS.

• The equipment shall be installed near the power supply so that the power supply is easily accessible.

• Do not touch hot spots during and immediately after use.

• During and immediately after use, this product is hot in areas other than the controls and rear panel connection jacks.

• Do not touch hot spots and especially the top panel. Contact with hot areas can cause burns.

• Do not expose the unit and batteries to excessive heat such as direct sunlight, ﬁ re or the like.

• Make a space of about 8 inchs (0.2 m) around the unit.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories speciﬁ ed by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table speciﬁ ed by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualiﬁ ed service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

AV_080602U2

INTRODUCTION

Thank you for purchasing the Marantz SR5003 Surround receiv er. This remarkable component has been engineered to provide you with many years of home theater enjo yment. Please take a few minutes to read this man ual thoroughly before you connect and operate the SR5003. As there are a number of connection and conﬁ guration options, you are encouraged to discuss your own particular home theater setup with your Marantz A/V authorized dealer.

ENGLISH

FUNCTION

NAMES AND

ACCESSORIES CHECK

Before use, check the below accessories were included in the package.

Remote Controller

AAA-size batteries (× 2)

AM Loop Antenna

FM Antenna

AC power cable

User Guide

Warranty Card

USA × 1 Canada × 1

BASIC

CONNECTIONS

BASIC OPERATION

ADVANCED

CONNECTIONS

SETUP

ADVANCED

OPERATION

Microphone

TROUBLESHOOTING

OTHERS

1

ENGLISH

NAMES AND

FUNCTION

TABLE OF CONTENTS

INTRODUCTION ....................................1

ACCESSORIES CHECK ....................................................1

TABLE OF CONTENTS .........................2

CONNECTIONS

FEA TURES .............................................2

BASIC

BEFORE USE .........................................3

OPERATION OF REMOTE CONTROLLER ......................4

NAMES AND FUNCTION ......................5

BASIC OPERATION

CONNECTIONS

SETUP

OPERATION

TROUBLESHOOTING

FRONT PANEL ...................................................................5

FL DISPLAY AND INDICATER ...........................................6

REMOTE CONTROLLER ..................................................7

REAR PANEL .....................................................................9

BASIC CONNECTIONS .......................10

SPEAKER PLACEMENT .................................................10

ADVANCED

CONNECTING SPEAKERS .............................................11

CONNECTING AUDIO COMPONENTS ..........................12

CONNECTING VIDEO COMPONENTS ..........................13

CONNECTING HDMI COMPONENTS ............................14

CONNECTING THE ANTENNA TERMINALS .................15

CONNECTING THE AC POWER CABLE .......................15

BASIC OPERATION ............................16

AMP OPERATION ............................................................16

TUNER OPERATION .......................................................16

REMOTE CONTROLLER OPERATION ..........................18

ADVANCED

ADVANCED CONNECTIONS ..............19

CONNECTING MULTI CHANNEL AUDIO COMPONENTS

CONNECTING AN EXTERNAL POWER AMPLIFIER ....19

CONNECTING FOR SPEAKER C USE (BI-AMP

CONNECTION) ................................................................20

CONNECTING THE REMOTE CONTROL JACKS .........20

CONNECTION FOR ANOTHER ZONE ...........................21

CONNECTING THE SATELLITE RADIO ........................22

CONNECTING OTHER EQUIPMENT .............................23

..19

SETUP ..................................................24

ONSCREEN DISPLAY MENU SYSTEM .........................24

1 INPUT SETUP .............................................................26

2 SPKR (SPEAKER) SETUP ..........................................29

ERROR MESSAGES .......................................................32

3 SURROUND SETUP ...................................................35

4 VIDEO SETUP .............................................................37

5 PREFERENCE ............................................................38

6 ACOUSTIC EQ ............................................................40

ADVANCED OPERATION ....................42

AMP OPERATION ............................................................42

TUNER OPERATION (PRESET MEMORY)....................47

XM RADIO OVERVIEW ...................................................49

LISTENING TO XM SATELLITE RADIO .........................49

SEARCH MODE ...............................................................51

PRESET MEMORY ..........................................................52

SIRIUS RADIO OVERVIEW .............................................54

LISTENING TO SIRIUS SATELLITE RADIO ...................54

SEARCH MODE ...............................................................56

PRESET MEMORY ..........................................................57

PARENTAL LOCK .............................................................58

ZONE SYSTEM ................................................................60

REMOTE CONTROLLER OPERATION ..........................62

BASIC OPERATION (REMOTE CONTROLLER) ...........64

TROUBLESHOOTING .........................66

HDMI .................................................................................67

XM SATELLITE RADIO ....................................................67

SIRIUS SATELLITE RADIO .............................................67

OTHERS ...............................................68

SURROUND MODE .........................................................68

DESCRIPTION .................................................................72

TECHNICAL SPECIFICATIONS ......................................75

CLEANING OF EQUIPMENT EXTERNAL SURFACES

REPAIRS...........................................................................75

..75

FEATURES

This unit incorporates the latest generation of digital surround sound decoding technology such as Dolby Digital EX, Dolby Digital, DTS ES (Discrete 6.1 and Matrix 6.1), DTS Neo:6 (Cinema, Music), Dolby ProLogic II (Movie, Music and Game), Dolby Pro-Logic IIx (Movie, Music and Game), Circle Surround II (Cinema, Music and Mono). Additionally , the unit is compatible with Dolb y TrueHD and DTS-HD (as used for Blu-ray and HD D VD discs) as well as Dolby Digital Plus, an expanded and improved version of Dolby Digital positioned as the next-generation delivery format. These audio formats can be sent with video signals via an HDMI cable to HDMI 1.3a-compatible equipment. In addition, Marantz has focused on the future. By utilizing pre-out jacks, 7.1 direct inputs and a RS-232C communication port, the unit is tomorrow’s technology, today!

This unit features a fully discrete 7 channel ampliﬁ er section capable of delivering 90 watts of high-current amplification, for continuously clean and stable power into each of the 7 channels. It employs a massive EI power transformer in combination with oversized ﬁ lter capacitors. This design conﬁ guration is capable of a clear and powerful reproduction of the most demanding action movie soundtracks and full range (multichannel) music discs. Through its ability to generate very high output voltages, the unit can easily drive the most demanding speakers with optimum results.

This unit incorporates the most advanced Digital Signal Processing circuitry, along with a 192 kHz/24 bit D/A converter in each of the 7 channels. Independent power supply circuits are incorporated for the FL display, audio and video sections for maximum separation, clarity and dynamic range. Together with hand-selected customized components, all elements work in harmony to recreate the emotion, exactly as the artist had intended.

OTHERS

2

This unit is designed and engineered with extensive feedback from custom installation experts, dealers and consumers. It features ZONE/multisource, assignable DC trigger, a RS-232C communication port, Flasher input, heavy duty speaker binding posts and an extensive array of both analog and digital inputs / outputs. With 5 assignable digital inputs (6 total), 3 component inputs, Super Audio CD Multi Channel (7.1 channel) direct inputs, video convert system and a speaker-B and OSD output versatility is taken to a stunning new level. Furthermore, the unit can output the OSD information through the Y/C (S-video) and composite video outputs.

ENGLISH

An easy-to-use programmable, learning remote controller allows full access to all of the operating functions and can be used for system operation as well.

The new generation of Marantz Receivers is stylish and completely symmetrical. On the front panel of the unit, buttons are kept to a minimum. Source selectors and volume controls are intuitively placed. This unit is here to perform in your unrivaled home entertainment setup.

HDMI (High-Deﬁ nition Multimedia Interface) is an enhancement to the DVI (Digital Visual Interface) standard. It adds capabilities for digitally transmitting audio signals in addition to video signals. Where multiple cables were previously needed for audio/ video, HDMI enables audio/video connection via a single cable. The HDMI input jacks of this unit support HDMI Ver.

1.3a. and the HDMI output jacks of this transmitter

support HDMI V er. 1.3a.

This unit supports HDCP (High-bandwidth Digital Content Protection). HDCP is copyright protection technology that consists of data encoding and other device authentication. Its purpose is to protect digital video content. Both this unit and the connected component (such as a video player or monitor) must support HDCP. Before connecting a component to this unit, refer to its instruction manual.

• x.v. Color

• Deep Color 36bit

• Dolby True HD, Dolby Digital Plus , dts HD

• Dolby Digital EX, Dolby Digital, DTS ES

(Discrete 6.1, Matrix 6.1, Neo:6)

• Dolby Headphone

• Dolby Pro Logic II (Movie, Music, Game)

• Dolby Pro Logic IIx (Movie, Music, Game)

• Circle Surround II (Cinema, Music, Mono)

• HDCD

• Bi-amp drive

• Source/Pure Direct mode

• 9 bands x 7 ch Graphic EQ

• DSD to PCM converter

• Audyssey MultEQ

• XM Satellite Radio Ready

• XM® HD Surround Powered by Neural Audio

• SIRIUS Satellite Radio Ready

• M-DAX (Marantz Dynamic Audio eXpander)

• Improved Station Name Input Method, 60 Presets

• Auto Adjust Function for Speaker Distance Settings

(Delay Time)

• Assignable DC Trigger Output

• Assignable Video Input

• Auto Lipsync (Audio Delay)

®

• 7 × 90 Watts (8 Ohms), Discrete Ampliﬁ ers

• Massive Energy Power Supply, Huge EI Transformer, Large ELCO’s.

• Function Rename

• 192 kHz/24 bit DA C for all 8 Channels

• 32 bit Digital Surround Processing Chipsets

• Auto Input Signal Detection

• Front Digital Optical Input

• ZONE B Output (Digital Optical Output)

• Video Off Mode Set Up Menu via all Video Output

• (Composite, S-Video, Component Video and HDMI)

• Video Up/Down Converter

(HDMI ← Component Video ↔ S-Video ↔ Composit Video)

• Two Component Monitor Outputs

• Analog Video Up-scaling to HDMI Output

(480i→480p→720p→1080i→1080p)

• RS-232C Terminal for Future Upgrade or System Control

• Flasher Input

• Full Backlight Learning Remote Controller

BEFORE USE

This section must be read before any connection is made to the mains supply.

EQUIPMENT MAINS WORKING SETTING

Your Marantz product has been prepared to comply with the household power and safety requirements that exist in your area. SR5003 can be powered by 120V AC only.

COPYRIGHT

Recording and playback of any material may require consent. For further information refer to the following:

— Copyright Act 1956 — Dramatic and Musical Perf ormers Act 1958 — Performers Protection Acts 1963 and 1972 —

Any subsequent statutory enactments and orders

DO NOT LOCATE IN THE FOLLOWING PLACES

To ensure long-lasting use, do not locate the unit where:

• Exposed to direct sunlight.

• Near to sources of heat such as heaters.

• Highly humid or poorly ventilated.

• Dusty.

• Subjected to mechanical vibrations.

•

On wobbly, inclined or otherwise unstable surfaces

• Radiated heat is blocked such as in cramped audio racks.

To ensure proper heat radiation, ensure the below clearance from walls and other equipment.

Above 8 inchs (0.2 m)

Left

8 inchs (0.2 m)

or more

Right

8 inchs (0.2 m)

or more

Rear

8 inchs (0.2 m)

or more

KEEP OBJECTS OFF

Keep objects off the unit. Bloc king the vent can result in accident and damage.

DO NOT TOUCH HOT SPOTS DURING AND IMMEDIATELY AFTER USE

During and immediately after use, the unit is hot in areas other than the controls and rear panel connection jacks. Do not touch hot spots and especially the top panel. Contact with hot areas can cause burns.

FUNCTION

NAMES AND

BASIC

CONNECTIONS

BASIC OPERATION

ADVANCED

CONNECTIONS

SETUP

ADVANCED

OPERATION

TROUBLESHOOTING

OTHERS

3

ENGLISH

NAMES AND

FUNCTION

OPERATION OF REMOTE CONTROLLER

REMOTE CONTROL

Operate the remote controller within a distance of approx. 16.4ft. (5m) from the infrared receptor window on the front of the unit.

CONNECTIONS

BASIC

Approx. 16.4ft. (5 m)

BASIC OPERATION

60°

Remote controller

CONNECTIONS

Caution:

ADVANCED

• Do not allow direct sunlight, an inverter ﬂ uorescent light or other strong source of light to shine onto the player’s infrared receptor window. Otherwise, the operation of the remote controller may be disabled.

• Bear in mind that operating the remote controller may cause other devices operated b y infrared ra ys to be operated by mistake.

SETUP

• The remote controller cannot be operated if the space between the controller and the player’s infrared receptor window is obstructed.

• Do not place any objects on top of the remote controller.

Doing so may cause one or more buttons to be

OPERATION

ADVANCED

held down which will cause the batteries to run down.

SR5003

LOADING BATTERIES

Before using the remote controller for the ﬁ rst time, load the batteries in the remote controller. The batteries provided are used to verify the operations of the remote controller only.

1. Remove the battery cover.

2. Insert the new batteries (AAA type) with correct ª and · polarity.

3. Close the battery cover until it clicks shut.

CAUTIONS ON BATTERIES

• Use “AAA” type batteries in this remote controller.

• We recommend that you use alkaline batteries.

• If the remote controller does not operate from close to the unit, replace the batteries with new ones, even if less then a y ear has passed.

• The included battery is only for verifying operation. Replace it with a new battery as soon as possible.

• When inserting the batteries, be careful to do so in the proper direction, following the + and - marks in the remote controller’s battery compartment.

• To prevent damage or battery ﬂ uid leakage:

- Do not use a new battery with an old one.

- Do not use two different types of batteries.

- Do not shor t-circuit, disassemble, heat or

dispose of batteries in ﬂ ames.

• Remove the batteries when not planning to use the remote controller for a long period of time.

• If the batteries should leak, carefully wipe off the ﬂ uid from the inside of the battery compar tment, then insert new batteries.

• When disposing of used batteries, please comply with governmental regulations or environmental public instruction’s rules that apply in your country or area.

TROUBLESHOOTING

OTHERS

4

ENGLISH

NAMES AND FUNCTION

FRONT PANEL

w!3

q POWER switc h and STANDBY

indicator

When this switch is pressed once, the unit turns ON and the display illuminates. When pressed again, the unit turns OFF and the STANDBY indicator will be illuminated.

w INPUT SELECTOR knob

(AUDIO/ VIDEO)

This knob is used to select the input sources. (See page 16)

e SURROUND MODE button

Press this button to select the surround mode.

r AUTO (Auto surround) button

Press this button to select the AUTO mode from the surround modes. When this mode is selected, the unit determines the surround mode corresponding to a digital input signal automatically.

e u i o !0 !1 !2t yq

r

!5!7!8 !6

t

PURE DIRECT button and indicator

When this button is pressed once, “SOURCE DIRECT” appears on the FL display. If pressed again,

“PURE DIRECT” appears. After 2 seconds, the FL display indication goes out. In the source/pure direct mode, the tone control circuitry and bass management are bypassed.

Notes:

• The surround mode is automatically switched to AUTO when the pure direct function is turned on.

• Additionally, speaker configurations are fixed automatically as follows.

Front SPKR = LARGE Center SPKR = LARGE Surround SPKR = LARGE Surround Back SPKR = LARGE Sub woofer = YES

!4

y DISPLAY button

Press this button to change the FL display mode.

u MENU button

Press this button to enter the SETUP MAIN MENU.

i EXIT button

Press this button to exit from the SETUP MAIN MENU.

o BAND button

Press this button to switch between FM and AM in the TUNER mode.

!0 T-MODE button

Press this button to select the auto stereo mode or mono mode when the FM band is selected. The “AUTO” indicator lights in the auto stereo mode. (See page 17)

!1 MEMORY button

Press this button to enter the tuner preset memory numbers or station names. (See page 47)

!2 CLEAR button

Press this button to cancel the station-memory setting mode or preset scan tuning. (See page 48)

!3 VOLUME contr ol knob

This knob is used to adjust the overall sound level. Turning the control clockwise increases the sound level.

!4

INFRARED receiving sensor window

This window receives infrared signals for the remote controller.

!5 AUX1 INPUT jac ks

These auxiliary video/audio input jacks accept the connections of a camcorder, portable DVD, game etc. When not using these jacks, protect by the jack cover .

!6

Cursor (

Press these buttons to operate the SETUP MAIN MENU and TUNER function.

5, ∞, 2, 3

) / ENTER button

!7 MIC jack

Automatically measure speaker characteristics using the included microphone. (See page 30)

!8

HEADPHONE jack for stereo headphones

This jack may be used to listen to the unit’s output through a pair of headphones. Be certain that the headphones have a standard 1/4” stereo phono plug.

FUNCTION

NAMES AND

BASIC

CONNECTIONS

BASIC OPERATION

ADVANCED

CONNECTIONS

SETUP

ADVANCED

OPERATION

TROUBLESHOOTING

OTHERS

5

ENGLISH

NAMES AND

FUNCTION

FL DISPLAY AND INDICATER

asd f hgk¡1 ¡2 ¡3¡4 ¡6 ¡7 ¡8

CONNECTIONS

BASIC

™1

BASIC OPERATION

a SP (speaker) ABC indicator

This indicator is illuminated when the speaker system is active.

s SLEEP timer indicator

This indicator is illuminated when the sleep timer function in the main-ZONE is in use.

CONNECTIONS

ADVANCED

d DISP (Display Off) indicator

This indicator is illuminated when this unit is in the display off mode.

f MULTI (ZONE system) AB

indicator

SETUP

This indicator is illuminated when the ZONE system is active.

g TUNER’s indicators

AUTO : This indicator illuminates when the

OPERATION

ADVANCED

TUNED : This indicator illuminates when the

ST(Stereo) : This indicator illuminates when an

TROUBLESHOOTING

tuner’s Auto mode is in use. tuner receives a sufﬁ ciently strong

radio signal. FM station is being tuned into stereo

condition.

h (Signal strength) indicator

This indicator indicates the strength of the XM Satellite Radio or SIRIUS Satellite Radio signal that is received.

j ATT (Attenuation) indicator

This indicator is illuminated when the attenuation

OTHERS

function is active.

¡5l¡0j

ex1 ex2

¡9™0

k PEAK indicator

This indicator is a monitor for an analog audio input signal. If the selected analog audio input signal is greater than the capable lev el of internal processing, this will illuminate. If this happens, you should press the ATT button. (See page 8)

l V-OFF (Video off mode) indicator

This indicator is illuminated when the Video-OFF function is active.

¡0 A-SURR

(Auto Surround mode) indicator

This indicator is illuminated when the AUTO SURROUND mode is in use.

¡1 EQ mode indicator

This indicator is illuminated when the HT-EQ function is active.

¡2 NIGHT mode indicator

This indicator is illuminated when this unit is in the Night mode, which reduces the dynamic range of digital program material at low volume levels.

¡3 M-DAX indicator

This indicator illuminates when this unit is in the MDAX mode.

¡4 HDMI indicator

This indicator is illuminated when the HDMI device is connected to the unit.

¡5 Audyssey indicator

This indicator is illuminated when the EQ MODE is selected to “AUDYSSEY”, “FRONT” or “AUDYSSEY FLA T”.

¡6 DIGITAL Input Indicator

This indicator is illuminated when a digital input has been selected.

¡7 ANALOG input indicator

This indicator is illuminated when an analog input source has been selected.

¡8 SIGNAL FORMAT indicators

2 TrueHD This indicator is illuminated when a Dolby Digital True HD signal is input. 2 DIGITAL This indicator is illuminated when a Dolby Digital signal is input. 2 DIGITAL PLUS This indicator is illuminated when a Dolby Digital Plus signal is input. 2 DIGITAL EX This indicator is illuminated when a Dolby Digital EX signal is input.

dts

This indicator is illuminated when a DTS signal is input.

dts-HD

This indicator is illuminated when a DTS-HD signal is input.

dts ES

This indicator is illuminated when a DTS ES signal is input.

dts MSTR

This indicator is illuminated when a Master Audio signal is input.

dts HIRES

This indicator is illuminated when a High Resulution Audio signal is input.

dts 96/24

This indicator is illuminated when a DTS 96/24 signal is input.

HDCD

This indicator is illuminated when the HDCD signal is decoded from digital input signal.

PCM

This indicator is illuminated when the input signal is PCM (pulse code modulation).

DSD

This indicator is illuminated when a DSD signal is input.

¡9

ENCODED CHANNEL STATUS indicators

These indicators display the channels that are encoded with a digital input signal. If the digital input signal is Dolby Digital 5.1ch or DTS 5.1ch, “L”, “C”, “R”, “SL”, “SR” and “LFE” will be illuminated. If the digital input signal is 2 channel PCM-audio, “L” and “R” will be illuminated. If the digital input signal is Dolby Digital 5.1ch signal with Surround EX ﬂ ag or DTS-ES, “L”, “C”, “R”, “SL”, “S” , “SR” and “LFE” will be illuminated. If the digital input signal is 7.1 channel PCM-audio. “L”, “C”, “R”, “SL”, “SBL”, “SR” “SBR”, and “LFE” will be illuminated. “ex1” or “ex2” illuminates when the digital input signal contains a channel other than those shown above. (See page 68.)

Note:

When the unit is decoding Dolby TrueHD, the input signal status displayed depends on the number of channels of the speakers used. If a 7.1-channel signal is supplied for a 5.1-channel speaker system (L/C/R/SL/SR/SW), the “SBL”, “SBR”, “S” indicator is not illuminated.

™0 Main Information Display

This display shows messages relating to the status, input source, surround mode, tuner, volume level or other aspects of unit’s operation.

™1 PURE DIRECT indicator

This indicator is illuminated when this unit is in the PURE DIRECT mode.

6

ENGLISH

REMOTE CONTROLLER

The provided remote controller is a universal remote controller. The POWER button, numeric buttons and control buttons are used in common across different input source components. The input source controlled with the remote controller changes when one of the input selector buttons is pressed.

‹5

‹4 ‹3

‹2 ‹1 ‹0 ¤9 ¤8

z x

c v b

¤7

¤6

n m

¤5 ¤4

¤3

, .

⁄0 ⁄1

¤2 ¤1

⁄2

⁄3

⁄4

¤0

⁄9

⁄5 ⁄6

z / POWER ON and OFF b uttons

(When AMP mode is selected)

These buttons are used to turn the unit on or off.

x Z.SPKR button

(When AMP mode is selected)

This button is used to turn on and off ZONE speaker.

c ZONE A / B buttons

These button are used to turn the ZONE system on or off.

v 7.1 (7.1CH IN) button

This button is used to select the output of an external multi channel decoder.

b SPKR A/B button

This button is used to select the speaker system. The speaker system is switched in the following sequence. A → B → A+B → off

n MUTE button

This button is used to mute the audio for the ampliﬁ er.

m LIGHT button

This button is used to turn on the backlight for the buttons.

, VOLUME +/- b uttons

This button is used to adjust the volume for the ampliﬁ er.

. SURR (SURROUND) button

(when a mode other than DMP is selected)

This button is used to selects the surround mode.

⁄1 1, 2, 3,

These buttons are used when controlling the cursor of the unit, DVD or other AV equipment.

(When Tuner mode mode is selected) PRESET +/ PRESET - buttons

Used to select a preset station up and down.

TUNE 3 /TUNE 4 buttons

Used to tune a frequency station up and down.

4

(CURSOR) / ENTER buttons

⁄2 EXIT / MEMO button

(When AMP mode is selected)

This button is used to cancel setting in the setup menu.

(When TUNER mode is selected)

This button is used to store the setting of preset channel and others.

⁄3 CONTROL buttons

These buttons are used when operating PLA Y, ST OP, PAUSE and other commands of a source.

(When TUNER mode is selected) T.MODE button

This button is used to select auto stereo mode or mono mode when the FM band is selected. The “AUTO” indicator lights in the auto stereo mode.

P.SCAN button

This button is used to start preset scan.

BAND button

This button is used to select a radio band.

T.DISP button

This button is used to select the display mode in XM Satellite Radio and SIRIUS Satellite Radio.

PTY button

These button is not used for this unit.

F.DIRECT button

This button is used to select the "Frequency direct input".

P.LOCK button

This button selects the parental lock of SIRIUS Satellite Radio.

⁄4 REPEAT button

This button is used to select the REPEAT mode of a source.

⁄5 RANDOM button

This button is used to select the RANDOM mode of a source.

⁄6 TV CONTROL buttons

These buttons are used when operating of TV and Monitor.

⁄7 BASS / CH +/- buttons

(When AMP mode is selected)

These buttons are used to adjust the tone control of low frequency sound for left, right and subwoofer speaker.

(When TV/DSS mode are selected)

These buttons are used to change channels.

⁄8 TREBLE / CAT +/- buttons

(When AMP mode is selected)

These buttons are used to adjust the tone control of high frequency sound for left and right speaker .

(When TUNER mode is selected)

These buttons select the categories available with XM Satellite Radio or SIRIUS Satellite Radio.

⁄9 CL (Clear) / HT EQ button

This button is used to erase the memory or program of a source include the Tuner mode.

(When AMP mode is selected)

This button is used to turn on or off HT(Home Theater)-EQ mode.

FUNCTION

NAMES AND

BASIC

CONNECTIONS

BASIC OPERATION

ADVANCED

CONNECTIONS

SETUP

ADVANCED

OPERATION

⁄7⁄8

⁄0 INFO button

(When AMP mode is selected)

When this button is pressed, the current setting of A V receiver are displayed on the connected TV monitor.

TROUBLESHOOTING

OTHERS

7

ENGLISH

NAMES AND

FUNCTION

¤0 Numeric buttons

These buttons are used to switch between 0 to +10 of the source components. If the source is set to the ampliﬁ er, these buttons are used to perform operations.

(When AMP mode is selected)

CONNECTIONS

1/AUT O button

This button is used to select auto surround.

BASIC

2/STEREO button

This button is used to select STEREO mode.

3/P.DIRECT button

When this button is pressed once, SOURCE DIRECT

BASIC OPERATION

mode is selected. If pressed again, PURE DIRECT mode is selected.

4/SLEEP button

This button is used for setting the sleep timer.

5/M-DAX button

This button is used to select M-DAX mode.

6/EQ button

CONNECTIONS

This button is used to select Audyssey mode .

ADVANCED

7/LIP SYNC button

This button is used to select LIP SYNC mode.

8/NIGHT button

Pressing this button prevents the Dolb y Digital signal from playback at a loud voice . When this button is pressed, the “NIGHT” indicator is illuminated.

SETUP

9/V.OFF buton

This button is used to turn off the video signal.

0/CH SEL button

This button is used to call up CH LEVEL ADJUST and adjust speaker levels or 7.1 ch input level.

OPERATION

ADVANCED

¤1 T.TONE button

This button is used to enter the test tone menu.

¤3 TOP button

Pressing this button during setup returns you to the top screen of the setup main menu.

¤4 DISPLAY button

(when a mode other than DMP is selected)

This button is used to selects the display mode for the front display of the unit.

¤5 INPUT 3 button

This button is for forward-feeding the input source to select a desired source.

INPUT 4 button

This button is for backward-feeding the input source to select a desired source.

¤6 SETUP button

This button is used to setup for DVD and other device.

¤7 SOURCE button

These buttons are used to switch the source of your A/V Receiver. Each time a source button is pressed, the remote controller changes to the source which was pressed. This remote controller can control 12 types of equipment. To change the A/V Receiver source, press this button twice within two seconds. The signal is sent when it is pressed the second time.

Notes:

• Select the AMP as the source to use this remote controller with the unit.

• In the case of the unit, the DMP button cannot be used.

¤9 A/D button

This button is used to switch between the analog and digital inputs.

‹0 HDMI button

These button is not used for this unit.

‹1 SET button

This button is used to enter learn mode and preset mode.

‹2 / SOURCE ON/OFF button

This button is used to turn a speciﬁ c source (such as a DVD player) on or off independently from the rest of the system.

‹3 SEND indicator

Indicates when the remote controller is transmitting a signal.

‹4 LEARN indicator

Indicates when the remote controller is in the LEARN mode.

‹5 Infrared Transmitter and Learning

Sensor

This transmitter emits infrared light. Press the b uttons while pointing the transmitter towards the infrared receiver window of the unit or other AV equipment. Be sure to also point towards other remote controllers when using the learning function.

¤2 MENU button

TROUBLESHOOTING

(When AMP mode is selected)

This button is used to call up the SETUP MAIN MENU of the unit.

OTHERS

8

¤8 ATT. button

When the input signal is too high and the voice distorts even by throttling the unit VOLUME control, turn on this function. “ATT” is indicated when this function is activated. The input level reduced. Attenuator is invalid for the output signal of “REC OUT”.

Note:

This function is unavailable while the digital input is selected.

ENGLISH

MODEL NO. SR5003

SWITCHED

1.25A 150W

UNSWITCHED

1.25A 150W

AC IN

SIRIUS

AC OUTLETS 120V 60Hz

R

L

R

AUDIO

OUTPUT 2

OUTPUT 1

INPUT 2

(

DVD

)

INPUT 3

(

VCR

)

INPUT 1

(

TV

)

COMPONENT

VIDEO

MONITOR OUT

C

R

/

P

R

C

B

/

P

B

Y

C

R

/

P

R

C

B

/

P

B

Y

C

R

/

P

R

C

B

/

P

B

Y

VCR OUT

VCR IN

(

3

)

TV

(

1

)

DVD

(

2

)

DSS

(

4

)

S-VIDEO

VIDEO

INPUT 3

(

VCR

)

INPUT 2

(

DVD

)

INPUT 1

(

TV

)

FM

(

Ω

)

GNDAMAM

ANTENNA

SR

C

SBR

SL

SBL

L

PRE OUT

ON

RS-232C

SPEAKER C

OFF

OUTPUT

CENTER

SURROUND

FRONT A

FRONT B

SURROUND BACK

SPEAKER C/

ZONE SPEAKER A

R

L

CD/CDR

OUTININ

TAPE

TV

DSS

VCR

DVD

OUT

IN

REMOTE CONT.

IN

OUT

3

1

4

DIGITAL IN

5

2

REC/ZONE B

DIGITAL

DC OUT

FLASHER IN

7.1CH INPUT

(

AUX 2

)

C

L

SBL

SBR

ZONE A

SPEAKER SYSTEMS

FRONT A OR B,CENTER, SURR,SURR BACK : 6-8 OHMS FRONT A + B : 8 OHMS

REAR PANEL

qwe rty

FM

(

)

GND

7575Ω

INPUT 1

L

R

RRSRSRSWSWSBR

(

AUX 2

L

RRSR

q FM antenna terminal (75 ohms)

Connect an external FM antenna with a coaxial cable, or a cable network FM source.

AM antenna and ground terminals

Connect the supplied AM loop antenna. Use the terminals marked “AM” and “GND”. The supplied AM loop antenna will provide good AM reception in most areas. Position the loop antenna until you hear the best reception.

w HDMI INPUT/OUTPUT

The unit has 3 HDMI inputs and 1 HDMI output.The input function can be selected from the system

. (See page 27)

e AUDIO IN/OUT (CD, TAPE, CD-R,

TV, DVD, VCR, DSS)

These are the analog audio inputs and outputs. There are 6 audio inputs (4 of which are linked to video inputs) and 3 audio outputs (1 of which are linked to video outputs). The audio jacks are nominally labeled for cassette tape decks, compact disc players, DVD

players and etc.... The audio inputs and outputs

require RCA-type connectors.

r

VIDEO IN/OUT (TV, DVD, VCR, DSS)

These are the video inputs and outputs. There are 4 video inputs and 1 video output and each one includes both composite video and S-video conﬁ gurations. Connect VCRs, DVD players, and other video components to the video inputs. The video output channel can be used to be connected to video tape recorders for making recordings.

ANTENNA

(

)

(

)

INPUT 2

DVD

TV

SLSLC

SBL

)

7.1CH INPUT

RS-232C

SPEAKER C

ON

OFF

C

SL

SBL

SWSWSBR

PRE OUT

(

)

INPUT 3

VCR

OUTPUT

TV

DVD

ZONE A

OUT

RRL

FRONT A

FRONT A OR B,CENTER, SURR,SURR BACK : 6-8 OHMS FRONT A + B : 8 OHMS

IN

VCR

OUT

FRONT B

SPEAKER SYSTEMS

TAPE

DSS

R

LLR

SURROUND

OSD menu

OUT

L

(

)

INPUT 1

OUT

1.25A 150W

SWITCHED

1.25A 150W

TV

C

B

/

P

B

Y

(

)

INPUT 2

DVD

SIRIUS

IN

VIDEO

S-VIDEO

(

)

(

)

VCR IN

TV

1

AUDIO

CD/CDR

DVD

2

DIGITAL IN

4

5

1

2

OUT

RRL

CENTER

SURROUND BACK

SPEAKER C/

ZONE SPEAKER A

(

)

DSS

4

(

)

MONITOR OUT

VCR OUT

3

DIGITAL

REMOTE CONT.

FLASHER IN

REC/ZONE B

3

DC OUT

OUT

AC OUTLETS 120V 60Hz

UNSWITCHED

!1

!3

!2!4!5@0@1 !7!8!9 !6

INPUT 3

C

B

/

P

B

Y

R

/

P

R

OUTPUT 1

AC IN

i

t MONITOR OUT

This is a monitor output and each one includes both composite video and S-video conﬁ gurations. When connecting two video monitors or televisions, be aware that the OSD interface can be used with both MONITOR OUT connections.

y COMPONENT VIDEO INPUT/

OUTPUT

If your DVD player or other device has component video connectors, be sure to connect them to these component video connectors on the unit. This unit has two component video input connectors to obtain the color information (Y, C recorded DVD signal or other video component and one component video output connector to output it directly into the matrix decoder of the display device. By sending the pure DVD component video signal directly, the DVD signal forgoes the extra processing that normally would degrade the image. The result is vastly increased image quality, with incredibly life like colors and crisp detail. When the video convert function is enabled, video and S-video images can be output to the COMPONENT VIDEO jack.

u XM terminal

Connect to the XM Mini-Tuner and Home Dock. (See page 22)

i AC INLET

Plug the supplied power cable into this AC INLET and then into the power outlet on the wall. This unit can be powered by 120V AC only.

B

, CR) directly from the

C

R

/

P

MODEL NO. SR5003

u!0o

o SIRIUS terminal

Connect to the SiriusConnectTM Home Tuner. (See page 22)

!0 AC OUTLETS

Connect the AC power cables of components such as

(

)

VCR

COMPONENT

VIDEO

a DVD and CD player to these outlets. SWITCHED and UNSWITCHED outlets are provided. The one marked SWITCHED provides power

C

B

/

P

B

Y

R

OUTPUT 2

only when the unit is turned on and is useful for

R

/

P

R

components which you use every time you play your system. The one marked UNSWITCHED is always live as long as the unit is plugged into a live outlet. A component connected here may be left on permanently, or may be switched off with via its own power switch.

Caution:

• In order to avoid potential turn-off thumps, anything plugged into these outlets should be powered up before the unit is turned on.

•

The capacity of this AC outlet is 150W. Do not connect devices that consume electricity more than the capacity of these AC outlets. If the total power consumption of the connected devices exceeds the capacity, the protection circuit shuts down the power supply.

!1 REMOTE CONT. IN/OUT terminals

!5 Speaker outputs terminals

Seven terminals are provided for the front left, front right, front center, surround left, surround right, surround back left and surround back right speakers.

Note:

You can use surround back speaker terminals as ZONE SPEAKER A terminals, when you use no surround back speaker.

!6 ZONE A Outputs

These are the audio output jacks for the ZONE A. Connect these jacks to optional audio power ampliﬁ ers to listen the source selected by the ZONE system in a remote room.

!7

SPEAKER C SELECTOR SWITCH

The terminals can be used to connect a third set of speakers by setting the SPEAKER C selector switch to ON. F or connection and use, see page 20.

!8 Preamp Outputs

(L, R, SL, SR, SBL, SBR, C)

Jacks for L(front left), R (front right), C (Center), SL (surround left), SR (surround right), SBL (surround back left) and SBR (surround back right). Use these jacks for connection to external power ampliﬁ ers.

FUNCTION

NAMES AND

BASIC

CONNECTIONS

BASIC OPERATION

ADVANCED

CONNECTIONS

Connect to a Marantz component equipped with remote control (RC-5) terminals.

!9 Subwoofer Output

Connect this jack to the line level input of a powered

!2 FLASHER IN

(Flasher input terminal)

These terminals are to control the unit from each ZONE. Connect the control signal from a Keypad, etc.

!3 DC TRIGGER output terminal

Connect a device that needs to be triggered by DC under certain conditions (screen, power strip, etc…) Use the system OSD setup menu to determine the conditions by which these jack will be active.

Note:

This output voltage is for (status) control only, It is not sufﬁ cient for drive capability.

!4 DIGITAL INPUT

(DIGITAL IN 1-5) / OUTPUT (optical)

These are the digital audio inputs and output. The unit has 2 digital inputs with coaxial jacks, 3 with

subwoofer . If an external subwoof er ampliﬁ er is used, connect this jack to the subwoofer ampliﬁ er input. If you are using two subwoofers, either powered or with a 2 channel subwoofer ampliﬁ er, connect a “Y” connector to the subwoofer output jack and run one cable from it to each subwoofer ampliﬁ er.

@0 RS-232C

The RS-232C port is to be used in conjunction with an external controller to control the operation of the unit by using an external device.

@1 7.1 CHANNEL or AUX2 INPUT

By connecting a DVD Audio player, Super Audio CD multichannel player, or other components that has a multichannel port, you can playback the audio with

5.1 channel or 7.1 channel outputs.

SETUP

ADVANCED

OPERATION

TROUBLESHOOTING

optical jacks. The inputs accept digital audio signals from a CD, DVD, or other digital source component. For digital output, this is 1 optical output. The digital outputs can be connected to MD recorders,

OTHERS

CD recorders, or other similar components. In addition, this digital output can be used as ZONE B output.

9

ENGLISH

NAMES AND

FUNCTION

BASIC CONNECTIONS

SPEAKER PLACEMENT

The ideal surround speaker system for this unit is 7speaker systems, using front left and right speakers,

CONNECTIONS

a center speaker, surround left and right speakers,

BASIC

a surround back left and right speakers, and a subwoofer . For best results we recommend that all front speakers be of the same type, with identical or similar driver units. This will deliver smooth pans across the front

BASIC OPERATION

sound stage as the action moves from side to side. Your center channel speaker is very important as over 80 % of the dialog from a typical motion picture emanates from the center channel. It should possess similar sonic characteristics to the main speakers. Surround channel speak ers need not be identical to the front channel speakers, but they should be of high quality.

CONNECTIONS

The surround center speaker is useful for playback

ADVANCED

of Dolby Digital Surround EX or DTS-ES. One of the beneﬁ ts of both Dolby Digital and DTS is that surround channels are discrete full range, while they were frequency limited in earlier “Pro Logic” type systems. Bass effects are an important part of home theater. For optimal enjoyment a subwoofer should be used as it is optimized for low frequency reproduction. If you

SETUP

have full range front speakers, however, they may be used in place of a subwoofer with proper setting of the switches in the menu system.

Subwoofer

Front Right

Front Center

Front Left

Surround Left

Surround Right

Surround Back Right

Surround Back Left

Front left and right speakers

We recommend to set the front L and R speakers with 45-60 degrees from the listening position.

Center speaker

Align the front line of the center speaker with the front L/R speakers. Or place the center speaker a little backward from the line.

Surround left and right speakers

When this unit is used in surround operation, the preferred location for surround speakers is on the side walls of the room, at or slightly behind the listening position. The center of the speaker should face into the room.

Surround back left and right speakers

Surround back speakers are required when a full 7.1channel system is installed. Speakers should be placed on a rear wall, behind the listening position. The center of the speaker should face into the room.

Subwoofer

We recommend using a sub-woofer to have maximum bass effect. As the subwoofer only handle lo w frequency . You can place it any where in the room.

HEIGHT OF THE SPEAKER UNITS

Front left and right speakers, and a center speaker

Align the tweeters and mid-range drivers on the three front speakers at the same height, as best as possible.

Surround left and right speakers, and surround back speaker

Place the surround left, right and surround back speakers higher than your ears by about 27-9/16 – 39-3/8 inchs (70cm–1m). Also place the speakers at the same height, as best as possible.

27-9/16 – 39-3/8 inchs (70cm–1m)

Note:

• Use magnetically-shielded speakers for front left, right and the center speakers when the speakers are installed near the TV.

OPERATION

ADVANCED

TROUBLESHOOTING

OTHERS

10

ENGLISH

MODEL NO. SR5003

SWITCHED

1.25A 150W

UNSWITCHED

1.25A 150W

AC IN

SIRIUS

AC OUTLETS 120V 60Hz

R

L

R

AUDIO

OUTPUT 2

OUTPUT 1

INPUT 2

(

DVD

)

INPUT 3

(

VCR

)

INPUT 1

(

TV

)

COMPONENT

VIDEO

MONITOR OUT

C

R

/

P

R

C

B

/

P

B

Y

C

R

/

P

R

C

B

/

P

B

Y

C

R

/

P

R

C

B

/

P

B

Y

VCR OUT

VCR IN

(

3

)

TV

(

1

)

DVD

(

2

)

DSS

(

4

)

S-VIDEO

VIDEO

INPUT 3

(

VCR

)

INPUT 2

(

DVD

)

INPUT 1

(

TV

)

FM

(

Ω

)

GNDAMAM

ANTENNA

SR

C

SBR

SBL

L

PRE OUT

ON

RS-232C

SPEAKER C

OFF

OUTPUT

CENTER

SURROUND

FRONT A

FRONT B

SURROUND BACK

SPEAKER C/

ZONE SPEAKER A

R

L

CD/CDR

OUTININ

TAPE

TV

DSS

VCR

DVD

OUT

IN

REMOTE CONT.

IN

OUT

3

1

4

DIGITAL IN

5

2

REC/ZONE B

DIGITAL

DC OUT

FLASHER IN

7.1CH INPUT

(

AUX 2

)

C

L

SBL

SBR

ZONE A

SPEAKER SYSTEMS

FRONT A OR B,CENTER, SURR,SURR BACK : 6-8 OHMS FRONT A + B : 8 OHMS

SW

PRE OUT

R

L

R

CENTER

SURROUND

FRONT A

FRONT B

SURROUND BACK

SPEAKER C/

ZONE SPEAKER A

SPEAKER SYSTEMS

FRONT A OR B,CENTER, SURR,SURR BACK : 6-8 OHMS FRONT A + B : 8 OHMS

CONNECTING SPEAKERS

Powered

subwoofer

FM

(

)

GND

7575Ω

ANTENNA

(

)

(

)

(

)

INPUT 3

INPUT 1

TV

SLSLC

L

R

RRSRSRSWSWSBR

(

)

7.1CH INPUT

AUX 2

RS-232C

SLSLSBL

L

RRSR

PRE OUT

INPUT 2

SPEAKER C

OFF

C

SWSWSBR

SW

DVD

SBL

ZONE A

OUT

ON

VCR

TV

RRL

FRONT A

FRONT A OR B,CENTER, SURR,SURR BACK : 6-8 OHMS

FRONT A + B : 8 OHMS

Caution:

Be sure to use speakers with the speciﬁ ed impedance as

• shown on the rear panel of this unit.

•

To prevent damage to circuitry, do not let the bare speaker wires touch each other and do not let them touch any metal part of this unit.

FUNCTION

NAMES AND

FRONT A Surround BACK

Right

Left

FRONT B

Right

Left

Right

Left

CONNECTING SPEAKER WIRE

1. Strip away approx. 3/8 inch (10 mm) of wire insulation.

Twist the bared wire ends tight, to prev ent short

2.

circuits. Loosen the knob by turning it counterclockwise.

3.

4. Insert the bare part of the wire into the hole in side of each terminal.

BASIC

Tighten the knob by turning it clockwise to

(

C

OUTPUT 1

B

/

P

B

INPUT 3

VCR

C

R

/

P

R

MODEL NO. SR5003

Y

)

COMPONENT

VIDEO

C

OUTPUT 2

C

R

/

P

R

B

/

P

B

(

)

INPUT 1

REMOTE CONT.

OUT

AC OUTLETS

120V 60Hz

UNSWITCHED

1.25A 150W

SWITCHED

1.25A 150W

TV

Y

C

R

/

P

R

C

B

/

P

B

Y

(

)

INPUT 2

DVD

SIRIUS

IN

AC IN

OUTPUT

DSS

VCR

DVD

OUT

IN

LLR

FRONT B

SPEAKER SYSTEMS

VIDEO

S-VIDEO

(

)

(

)

TV

1

AUDIO

CD/CDR

TAPE

OUT

R

L

R

L

SURROUND

DVD

2

4

5

1

2

OUT

RRL

CENTER

SURROUND BACK

CENTER

SURROUND BACK

SPEAKER C/

ZONE SPEAKER A

VCR IN

DIGITAL IN

(

)

DSS

4

(

)

MONITOR OUT

VCR OUT

3

DIGITAL

FLASHER IN

REC/ZONE B

3

DC OUT

OUT

5.

secure the wire.

1. 2.

3/8 inch

(10 mm)

3. 4. 5.

• Do not touch the speaker terminals when the power is on. It may cause you to receive an electric shocks.

• Do not connect more than one speaker cable to one speaker terminal. Doing so may damage this unit.

Note:

•

Be sure to connect the positive and negative cables for the speaker properly. If they are miss-connected, the signal phase will be reversed and the signal quality will

BASIC

CONNECTIONS

BASIC OPERATION

be corrupted.

CONNECTING A SUBWOOFER

Use the PRE OUT SUBWOOFER jack to connect a

ADVANCED

CONNECTIONS

powered subwoofer (pow er ampliﬁ er b uilt in ).

Right Left

Surround

Center

SETUP

ADVANCED

OPERATION

TROUBLESHOOTING

OTHERS

11

ENGLISH

SWITCHED

1.25A 150W

UNSWITCHED

1.25A 150W

CAC IN

SIRIUS

AC OUTLETS 120V 60Hz

R

L

R

AUDIO

INPUT 2

(

DVD

)

INPUT 1

(

TV

)

MONITOR OUT

C

R

/

P

R

C

B

/

P

B

Y

VCR OUT

VCR IN

(

3

)

TV

(

1

)

DVD

(

2

)

DSS

(

4

)

S-VIDEO

VIDEO

INPUT 3

(

VCR

)

INPUT 2

(

DVD

)

INPUT 1

(

TV

)

FM

(

Ω

)

GNDAMAM

ANTENNA

SR

C

SBR

SBL

L

PRE OUT

ON

RS-232C

SPEAKER C

OFF

OUTPUT

CENTER

SURROUND

FRONT A

FRONT B

SURROUND BACK

SPEAKER C/

ZONE SPEAKER A

R

L

CD/CDR

OUTININ

TAPE

TV

DSS

VCR

DVD

OUT

IN

REMOTE CONT.

IN

OUT

3

1

4

DIGITAL IN

5

2

REC/ZONE B

DIGITAL

DC OUT

FLASHER IN

7.1CH INPUT

(

AUX 2

)

C

L

SBL

SBR

ZONE A

SPEAKER SYSTEMS

FRONT A OR B,CENTER, SURR,SURR BACK : 6-8 OHMS FRONT A + B : 8 OHMS

5

AUDIO

CD/CDR

OUTININ

TAPE

R

L

DIGITAL IN

REC/ZONE B

DIGITAL

OUT

NAMES AND

FUNCTION

CONNECTING AUDIO COMPONENTS

CD recorder

CONNECTIONS

BASIC

OUT IN

L R L

R L

R

R L

DIGITAL

INPUT

DIGITAL

OUTPUT

BASIC OPERATION

CONNECTIONS

ADVANCED

SETUP

FM

(

)

GND

7575Ω

(

)

INPUT 1

TV

SLSLC

L

R

RRSRSRSWSWSBR

(

)

7.1CH INPUT

AUX 2

RS-232C

SLSLSBL

L

RRSR

PRE OUT

INPUT 2

SPEAKER C

OFF

C

SWSWSBR

ANTENNA

(

ON

(

)

INPUT 3

VCR

DVD

SBL

TV

ZONE A

OUT

FRONT A OR B,CENTER, SURR,SURR BACK : 6-8 OHMS FRONT A + B : 8 OHMS

)

RRL

FRONT A

The output audio signal from the TAPE OUT jack and the CD/CD RECORDER OUT jack is the same signal

OUT IN

LRL

Tape Dec k

R

which is currently selected.

Caution:

• Do not connect this unit and other components to mains power until all connections between components have been completed.

L R

Notes:

• Insert all plugs and connectors securely. Incomplete connections may make noise.

• Be sure to connect the left and right channels

RL RL

(

)

INPUT 1

REMOTE CONT.

OUT

AC OUTLETS 120V 60Hz

UNSWITCHED

1.25A 150W

SWITCHED

1.25A 150W

TV

C

R

/

P

R

C

B

/

P

B

Y

(

)

INPUT 2

DVD

SIRIUS

IN

A

OUTPUT

DSS

VCR

DVD

OUT

IN

LLR

FRONT B

SPEAKER SYSTEMS

VIDEO

S-VIDEO

(

)

(

)

TV

1

AUDIO

DVD

CD/CDR

TAPE

CD/CDR

TAPE

OUT

R

L

SURROUND

2

4

5

1

2

OUT

RRL

CENTER

SURROUND BACK

SPEAKER C/

ZONE SPEAKER A

VCR IN

DIGITAL IN

(

)

DSS

4

(

)

MONITOR OUT

VCR OUT

3

DIGITAL

FLASHER IN

REC/ZONE B

3

DC OUT

OUT

properly.

Red connectors are for the R (right) channel, and

white connectors are for the L (left) channel.

• Be sure to connect input and output properly.

• Refer to the instructions for each component that is connected to this unit.

• Do not bind audio/video connection cables with power cables and speaker cables this will result in generating a hum or other noise.

CONNECTING DIGITAL AUDIO COMPONENTS

• There are 5 digital inputs, 2 coaxial jacks and 3 optical jacks, on the rear panel. You can use these jacks to input PCM, Dolby Digital and DTS bitstream signals from a CD, DVD, or other digital source components.

• There is one optical output jack on the rear panel. This jack can be connected to a CD recorder or a MD recorder input. When this jack is used for ZONE B, it cannot be used for recorded audio output.

(See pages 9 and 39.)

• Refer to the instructions for each component. To setup the digital audio format of DVD player, or other digital source’s connected to digital input jacks.

• Use ﬁ ber optical cables (optical) for DIG-1,2,3 input jacks and REC/ZONE B output jack. Use 75 ohms coaxial cables (for digital audio or video) for DIG-4, 5 input jacks.

• You can designate the input for each digital input/ output jacks according to your component. See page 27.

Notes:

• The digital signal jacks on this unit conform to

R L R L

the EIA standard. If you use a cable that does not conform to this standard, this unit may not function properly.

• Each type of audio jack works independently. Signals input through the digital and analog jacks are output through the corresponding digital and analog jacks, respectively.

OPERATION

ADVANCED

Analog Audio

Digital Audio (coaxial)

TROUBLESHOOTING

OTHERS

12

Digital Audio (optical)

L R

ENGLISH

MODEL NO. SR5003

SWITCHED

1.25A 150W

UNSWITCHED

1.25A 150W

IAC IN

SIRIUS

AC OUTLETS

120V 60Hz

R

L

R

AUDIO

OUTPUT 2OUTPUT 1

INPUT 2

(

DVD

)

INPUT 3(VCR

)

INPUT 1

(

TV

)

COMPONENT

VIDEO

MONITOR OUT

C

R

/

PRC

B

/

P

B

Y

C

R

/

PRC

B

/

P

B

Y

C

R

/

P

R

C

B

/

P

B

Y

VCR OUT

VCR IN

(

3

)

TV

(

1

)

DVD

(

2

)

DSS

(

4

)

S-VIDEO

VIDEO

INPUT 3

(

VCR

)

INPUT 2

(

DVD

)

AM

ANTENNA

C

SBR

SBLL

O

ON

SPEAKER C

OFF

OUTPUT

CENTER

SURROUND

FRONT A

FRONT B

SURROUND BACK

SPEAKER C/

ZONE SPEAKER A

CD/CDR

OUTININ

TAPE

TV

DSS

VCR

DVD

OUT

IN

REMOTE CONT.

IN

OUT

3

1

4

DIGITAL IN

5

2

REC/ZONE B

DIGITAL

DC OUT

FLASHER IN

SBL

SBR

ZONE A

SPEAKER SYSTEMS

FRONT A OR B,CENTER, SURR,SURR BACK : 6-8 OHMS FRONT A + B : 8 OHMS

4

TV

(

1

)

DSS

(

4

)

MONITOR OUT

S-VIDEO

VIDEO

TV

DSS

DIGITAL IN

MODEL NO. SR5003

SWITCHED

1.25A 150W

UNSWITCHED

1.25A 150W

AC IN

SIRIUS

AC OUTLETS 120V 60Hz

R

L

R

AUDIO

OUTPUT 2

OUTPUT 1

INPUT 2

(

DVD

)

INPUT 3

(

VCR

)

INPUT 1

(

TV

)

COMPONENT

VIDEO

MONITOR OUT

C

R

/

P

RR

C

B

/

P

B

Y

C

R

/

P

R

C

B

/

P

B

Y

C

R

/

P

R

C

B

/

P

B

Y

VCR OUT

VCR IN

(

3

)

TV

(

1

)

DVD

(

2

)

DSS

(

4

)

S-VIDEO

VIDEO

INPUT 3

(

VCR

)

(

DVD

)

ANTENNA

SBR

SBL

ON

OUTPUT

CENTER

SURROUND

FRONT A

FRONT B

SURROUND BACK

SPEAKER C/

ZONE SPEAKER A

CD/CDR

OUTININ

OUT

IN

TAPE

TV

DSS

VCR

DVD

OUTININ

REMOTE CONT.

IN

OUT

3

1

4

DIGITAL IN

5

2

REC/ZONE B

DIGITAL

DC OUT

FLASHER IN

SBL

SBR

ZONE A

SPEAKER SYSTEMS

FRONT A OR B,CENTER, SURR,SURR BACK : 6-8 OHMS FRONT A + B : 8 OHMS

VCR

DVD

OUTININ

DIGITAL IN

OUTPUT 1

INPUT 2

(

DVD

)

INPUT 3

(

VCR

)

INPUT 1

(

TV

)

COMPONENT

VIDEO

C

R

/

P

R

C

B

/

P

B

Y

C

R

/

P

R

C

B

/

P

B

Y

MONITOR OUT

VCR OUT

VCR IN

(

3

)

DVD

(

2

)

S-VIDEO

VIDEO

2

CONNECTING VIDEO COMPONENTS

AUDIO

F

UT 2

T

PEAKER C

ON

ANTENNA

DIGITAL

OUT

(

)

DVD

SBL

SBR

SBL

SBR

INPUT 3

ZONE A

OUT

FRONT A OR B,CENTER, SURR,SURR BACK : 6-8 OHMS FRONT A + B : 8 OHMS

(

VCR

TV

RRL

OUT LR

L R

R L

)

FRONT A

OUTPUT

DVD

L R LR

VIDEO

VCR

DVD player

OUT

DSS

OUT

LLR

FRONT B

SPEAKER SYSTEMS

L LR R

AUDIO

OUT

LR

IN

TAPE

OUT

R

SURROUND

AUDIO

IN

LR

S-VIDEO

L

OUT

AUDIO

CD/CDR

VIDEO

S-VIDEO

OUT

CENTER

COMPONENT

VIDEO OUT

YC

(

)

TV

1

4

1

RRL

SURROUND BACK

SPEAKER C/

ZONE SPEAKER A

VIDEO

OUT IN

VCR

DVD

5

2

B

(

2

/ PBCR

)

VCR IN

DIGITAL IN

VIDEO, S-VIDEO, COMPONENT JACKS

There are 3 types of video jacks on the rear panel.

VIDEO

PROJECTOR

Satellite Tuner

VIDEO jack

The video signal for the VIDEO jacks is the conventional composite video signal.

FUNCTION

NAMES AND

S-VIDEO jack

COMPONENT

VIDEO IN

YC

B

/ PR

/ PBCR

S-VIDEO

/ PR

IN

DIGITAL

OUT

AUDIO

OUT

VIDEO

OUT

S-VIDEO

OUT

L R

The video signal is separated into luminance (Y) and color (C) signals for the S-VIDEO jack. The S-VIDEO signals enables high-quality color reproduction. If your video component has an S-VIDEO output, we recommend to use it. Connect the S-VIDEO output jack on your video component to the S-VIDEO input

BASIC

CONNECTIONS

jack on this unit.

COMPONENT jack

L R

(

INPUT 1

REMOTE CONT.

OUT

AC OUTLETS 120V 60Hz

UNSWITCHED

1.25A 150W

SWITCHED

1.25A 150W

TV

C

B

/

P

B

Y

(

INPUT 2

DVD

IN

(

C

OUTPUT 1

B

/

B

/

INPUT 3

P

B

P

B

(

VCR

C

R

/

P

R

C

R

/

P

R

MODEL NO. SR5003

)

Y

COMPONENT

VIDEO

C

OUTPUT 2

VIDEO

AM

ANTENNA

(

)

(

)

INPUT 3

DVD

ZONE A

OUT

ON

SBL

VCR

OUTPUT

TV

VCR

DVD

TV

IN

RRL

FRONT A

FRONT A OR B,CENTER, SURR,SURR BACK : 6-8 OHMS FRONT A + B : 8 OHMS

OUT

FRONT B

DSS

LLR

SPEAKER SYSTEMS

C

R

/

P

B

/

P

B

INPUT 2

NPUT

CCLSBL

SWSWSBR

SPEAKER C

OFF

C

SWSWSBR

UT

VIDEO

S-VIDEO

(

)

(

)

(

)

TV

1

TV

1

AUDIO

DVD

CD/CDR

TAPE

OUT

R

L

SURROUND

2

4

5

4

1

2

OUT

RRL

CENTER

SURROUND BACK

SPEAKER C/

ZONE SPEAKER A

VCR IN

DIGITAL IN

(

)

(

)

DSS

4

DSS

4

(

)

MONITOR OUT

VCR OUT

3

DIGITAL

FLASHER IN

REC/ZONE B

3

DC OUT

OUT

LR

Video

(

)

(

)

INPUT 1

TV

INPUT 1

TV

(

)

DSS

4

(

)

(

)

MONITOR OUT

VCR OUT

3

VCR OUT

3

DIGITAL

REC/ZONE B

3

OUT

FLASHER IN

DC OUT

REMOTE CONT.

AC OUTLETS

UNSWITCHED

OUT

120V 60Hz

1.25A 150W

SWITCHED

1.25A 150W

IN

Y

INPUT 2

C

B

/

P

C

B

/

P

B

(

DVD

Y

C

R

/

P

R

Y

C

R

/

P

R

)

SIRIUS

AC IN

S-Video

L R

Analog Audio

AUDIO

OUT

LR

VIDEO

OUT

VIDEO

IN

S-VIDEO

IN

L R

Digital Audio (coaxial)

Make component video connections to a TV or monitor with component inputs to produce higher quality video images. Use a component video cable

)

or 3 video cords to connect the component video out jacks on the unit to the monitor.

C

R

/

P

R

)

SIRIUS

Notes:

Be sure to connect the left and right audio channels

• properly.

Red connectors are for the R (right) channel, and

white connectors are for the L (left) channel.

AC

• Be sure to connect the inputs and outputs of the video signals properly.

•

If you connect the S-VIDEO or component signal to the S-VIDEO or component jack on this unit, it is not necessary to connect the conventional video signal to the VIDEO (composite) jack. If you use both video inputs, this unit gives priority to the S-VIDEO signal.

• Each type of video jack works independently. Signals input to the VIDEO (composite) and SVIDEO jacks or component are output to the corresponding VIDEO (composite) and S-VIDEO or component jacks, respectively.

•

T

his unit

has the “TV-AUTO ON/OFF” function to turn the TV ON or OFF automatically , by sensing the incoming video signal from the VIDEO jacks.

• You may need to setup the digital audio output

BASIC OPERATION

ADVANCED

CONNECTIONS

SETUP

ADVANCED

OPERATION

format of your DVD player, or other digital source

S-VIDEO OUT IN

TV

Digital Audio (optical)

components. Refer to the instructions of the each component connected to the digital input jacks.

• The COMPONENT OUTPUT 1 and 2 terminals of this unit can output the same video signal. (See page

37)

TROUBLESHOOTING

OTHERS

13

ENGLISH

MODEL NO. SR5003

SWITCHED

1.25A 150W

UNSWITCHED

1.25A 150W

AC IN

SIRIUS

AC OUTLETS 120V 60Hz

R

L

R

AUDIO

OUTPUT 2

OUTPUT 1

INPUT 2

(

DVD

)

INPUT 3

(

VCR

)

INPUT 1

(

TV

)

COMPONENT

VIDEO

MONITOR OUT

C

R

/

P

R

C

B

/

P

B

Y

C

R

/

P

R

C

B

/

P

B

Y

C

R

/

P

R

C

B

/

P

B

Y

VCR OUT

VCR IN

(

3

)

TV

(

1

)

DVD

(

2

)

DSS

(

4

)

S-VIDEO

VIDEO

INPUT 3

(

VCR

)

INPUT 2

(

DVD

)

INPUT 1

(

TV

)

FM

(

Ω

)

GNDAMAM

ANTENNA

SR

C

SBR

SL

SBL

L

PRE OUT

ON

RS-232C

SPEAKER C

OFF

OUTPUT

CENTER

SURROUND

FRONT A

FRONT B

SURROUND BACK

SPEAKER C/

ZONE SPEAKER A

R

L

CD/CDR

OUTININ

TAPE

TV

DSS

VCR

DVD

OUT

IN

REMOTE CONT.

IN

OUT

3

1

4

DIGITAL IN

5

2

REC/ZONE B

DIGITAL

DC OUT

FLASHER IN

7.1CH INPUT

(

AUX 2

)

C

L

SBL

SBR

ZONE A

SPEAKER SYSTEMS

FRONT A OR B,CENTER, SURR,SURR BACK : 6-8 OHMS FRONT A + B : 8 OHMS

INPUT 3

(

VCR

)

INPUT 2

(

DVD

)

OUTPUT

NAMES AND

FUNCTION

CONNECTING HDMI COMPONENTS

CONNECTIONS

BASIC

BASIC OPERATION

FM

(

)

GND

7575Ω

INPUT 1

L

R

RRSRSRSWSWSBR

(

CONNECTIONS

ADVANCED

SETUP

AUX 2

L

RRSR

SATELLITE TUNER

HDMI OUTPUT

RS-232C

ANTENNA

(

)

(

)

INPUT 2

TV

INPUT 2

SLSLC

)

7.1CH INPUT

SPEAKER C

OFF

C

SL

SWSWSBR

PRE OUT

(

)

INPUT 3

DVD

INPUT 3

DVD

SBL

ZONE A

OUT

ON

SBL

(

VCR

TV

RRL

FRONT A OR B,CENTER, SURR,SURR BACK : 6-8 OHMS FRONT A + B : 8 OHMS

DVD player VIDEO PROJECTOR

HDMI OUTPUT HDMI INPUT

R

SURROUND

VIDEO

S-VIDEO

AUDIO

CD/CDR

OUT

L

CENTER

(

)

TV

1

DVD

4

1

RRL

SURROUND BACK

SPEAKER C/

ZONE SPEAKER A

(

)

(

)

VCR OUT

VCR IN

3

2

DIGITAL IN

REC/ZONE B

5

3

2

)

FRONT A

OUTPUT

TAPE

DSS

VCR

DVD

OUT

IN

LLR

FRONT B

SPEAKER SYSTEMS

HDMI JACKS

This unit has three HDMI inputs and one HDMI output. It can send digital video and audio signals from DVDs and other sources directly to a display. It minimizes signal degradation caused by analog conversion so that high quality images can be enjoyed. This unit is also capable of converting analog video signals (Composite Video, S-Video, Component Video) for HDMI output. Select an input source from the OSD menu system. (See page 27)

• Some source devices such as DVD players or set top box do not support HDMI repeater operations like those of the unit. In such case, pictures are not properly projected on monitors such as TVs and projectors.

• When multiple components are connected to this unit, turn power to unused components off to prevent interference between them.

• Disconnecting or connecting cables with the power on can damage the equipment. Turn the power off before disconnecting or connecting cables.

• If the DVD player that does not support HDMI 1.1 or later is connected to the unit, multi channel PCM

Notes:

(

C

B

/

P

INPUT 3

B

VCR

C

R

/

P

R

MODEL NO. SR5003

)

Y

COMPONENT

VIDEO

C

OUTPUT 2

C

R

/

P

R

B

/

P

B

(

)

INPUT 1

TV

(

)

DSS

4

MONITOR OUT

Y

REMOTE CONT.

OUT

AC OUTLETS 120V 60Hz

UNSWITCHED

1.25A 150W

SWITCHED

1.25A 150W

INPUT 2

IN

DIGITAL

FLASHER IN

DC OUT

OUT

Y

C

R

/

P

R

C

B

/

P

B

(

)

OUTPUT 1

DVD

SIRIUS

AC IN

• When the HDMI output is connected to a display monitor that does not support HDCP

*, signals are

not output. T o view images in HDMI, it is necessary to connect to a display that supports HDCP.

• There may be no image output if connected to a TV or display that is not compatible with the above format.

• Refer to the instruction manual of the TV or display to be connected to the unit for detailed information regarding the HDMI terminal.

* HDCP: High-bandwidth Digital Content Protection

CONNECTING HDMI COMPONENTS

An HDMI cable (sold separately) is used to connect the HDMI jack on the unit with the HDMI jack on the DVD player, TV, projector or other component. To transmit multichannel audio via HDMI, the connected player must support multichannel audio transmission through its HDMI jack.

playback is not possible even with DVD-Audio disks.

• If the Super Audio CD player that does not support HDMI 1.2 or later is connected to the unit, DSD playback is not possible even with Super Audio CD.

(*DSD: Direct Stream Digital)

• The following functions are not available when the unit is connected to equipment that does not support HDMI 1.3a.

• Deep Color

• x.v. Color

• Bitstream audio signal decoding, as for Dolby

Digital Plus, Dolby TrueHD, DTS-HD, and so on

For details, refer to the user’s manuals of connected

equipment.

• Multi channel PCM signals and audio signals of 64 kHz or higher that are input from the HDMI jack are not output from the DIGITAL OUT jack.

• Depending on the quiality of the cable used, the HDMI signal may be affected by noise.

OPERATION

ADVANCED

TROUBLESHOOTING

OTHERS

14

Notes:

• Some HDMI components can be controlled over the HDMI cable, but this unit cannot control other components this way.

• When connected to a monitor (i.e., TV, projector, etc.) that does not support HDCP, video and audio are not output.

ENGLISH

MODEL NO. SR5003

SWITCHED

1.25A 150W

UNSWITCHED

1.25A 150W

AC IN

SIRIUS

AC OUTLETS

120V 60Hz

R

L

R

AUDIO

OUTPUT 2

OUTPUT 1

INPUT 2

(

DVD

)

INPUT 3

(

VCR

)

INPUT 1

(

TV

)

COMPONENT

VIDEO

MONITOR OUT

C

R

/

PRC

B

/

P

B

Y

C

R

/

P

R

C

B

/

P

B

Y

C

R

/

P

R

C

B

/

P

B

Y

VCR OUT

VCR IN

(

3

)

TV

(

1

)

DVD

(

2

)

DSS

(

4

)

S-VIDEO

VIDEO

INPUT 3

(

VCR

)

INPUT 2

(

DVD

)

INPUT 1

(

TV

)

FM

(

Ω

)

GNDAMAM

ANTENNA

SR

C

SBR

SL

SBL

L

PRE OUT

ON

RS-232C

SPEAKER C

OFF

OUTPUT

CENTER

SURROUND

FRONT A

FRONT B

SURROUND BACK

SPEAKER C/

ZONE SPEAKER A

R

L

CD/CDR

OUTININ

TAPE

TV

DSS

VCR

DVD

OUT

IN

REMOTE CONT.

IN

OUT

3

1

4

DIGITAL IN

5

2

REC/ZONE B

DIGITAL

DC OUT

FLASHER IN

7.1CH INPUT

(

AUX 2

)

C

L

SBL

SBR

ZONE A

SPEAKER SYSTEMS

FRONT A OR B,CENTER, SURR,SURR BACK : 6-8 OHMS FRONT A + B : 8 OHMS

FM

(

Ω

)

GNDAMAM

ANTENNA

))

GNDGND AMAM

ANTANTENNA

MODEL NO. SR5003

SWITCHED

1.25A 150W

UNSWITCHED

1.25A 150W

AC IN

SIRIUS

AC OUTLETS 120V 60Hz

L

OUTPUT 2

OUTPUT 1

INPUT 2

(

DVD

)

INPUT 3

(

VCR

)

INPUT 1

(

TV

)

COMPONENT

VIDEO

MONITOR OUT

C

R

/

P

R

C

B

/

P

B

Y

C

R

/

P

R

C

B

/

P

B

Y

C

R

/

P

R

C

B

/

P

B

Y

VCR OUT

VCR IN

(

3

)

DVD

(

2

)

DSS

(

4

)

SPEAKER C/

REMOTE CONT.

IN

OUT

31

DIGITAL IN

5

2

REC/ZONE B

DIGITAL

DC OUT

FLASHER IN

AC IN

CONNECTING THE ANTENNA TERMINALS

FM Antenna

FM

(

)

(

)

GND

7575Ω

(

)

INPUT 1

TV

SLSLC

L

R

RRSRSRSWSWSBR

(

)

7.1CH INPUT

AUX 2

RS-232C

SL

L

RRSR

PRE OUT

ASSEMBLING THE AM LOOP ANTENNA

INPUT 2

SPEAKER C

ON

OFF

C

SWSWSBR

ANTENNA

(

DVD

SBL

FM External

Antenna

(

)

INPUT 3

VCR

TV

DVD

ZONE A

OUT

RRL

FRONT A

FRONT A OR B,CENTER, SURR,SURR BACK : 6-8 OHMS FRONT A + B : 8 OHMS

OUTPUT

VCR

OUT

IN

FRONT B

DSS

LLR

SPEAKER SYSTEMS

CONNECTING THE SUPPLIED ANTENNAS

AM Loop

Antenna

VIDEO

S-VIDEO

AUDIO

CD/CDR

TAPE

OUT

R

L

CENTER

SURROUND

(

)

TV

1

DVD

4

1

RRL

SURROUND BACK

SPEAKER C/

ZONE SPEAKER A

(

)

(

)

VCR OUT

VCR IN

3

2

DIGITAL

DIGITAL IN

REC/ZONE B

5

3

2

OUT

DSS

FLASHER IN

(

)

4

DC OUT

AM External

MONITOR OUT

REMOTE CONT.

IN

OUT

AC OUTLETS 120V 60Hz

UNSWITCHED

1.25A 150W

SWITCHED

1.25A 150W

Antenna

(

INPUT 1

TV

C

B

/

P

B

Y

(

INPUT 2

DVD

)

C

)

SIRIUS

INPUT 3

C

R

C

B

/

P

B

Y

R

/

P

R

OUTPUT 1

AC IN

Connecting the supplied FM antenna

The supplied FM antenna is for indoor use only. During use, extend the antenna and move it in v arious directions until the clearest signal is received. Fix it with push pins or similar implements in the position that will cause the least amount of distortion. If you experience poor reception quality, an outdoor antenna may improve the quality.

Connecting the supplied AM loop antenna

(

)

VCR

The supplied AM loop antenna is for indoor use only. Set it in the direction and position it to where you

Y

/

P

R

receive the clearest sound. Put it as far away as possible from the unit, televisions, speaker cables, and power cords. If you experience poor reception quality, an outdoor antenna may improve the quality.

MODEL N

Press and hold down the lever of the AM antenna

1.

terminal.

2. Insert the bare wire into the antenna terminal. Release the lever.

3.

Note:

CONNECTING THE AC POWER CABLE

1. Plug the supplied AC power cable to the AC IN socket on the rear panel of the unit.

(

C

OUTPUT 1

B

/

P

INPUT 3

B

VCR

C

R

/

P

R

MODEL NO. SR5003

)

Y

COMPONENT

VIDEO

C

OUTPUT 2

C

R

/

P

R

B

/

P

B

(

)

INPUT 1

TV

(

)

DSS

4

(

)

(

)

DVD

2

5

2

RRL

URROUND BACK

SPEAKER C/

ONE SPEAKER A

VCR IN

DIGITAL IN

MONITOR OUT

VCR OUT

3

DIGITAL

REC/ZONE B

3

OUT

FLASHER IN

DC OUT

REMOTE CONT.

OUT

AC OUTLETS 120V 60Hz

UNSWITCHED

1.25A 150W

SWITCHED

1.25A 150W

Y

INPUT 2

IN

Y

C

R

/

P

R

C

B

/

P

B

(

)

DVD

SIRIUS

AC IN

2. Plug the power cable into an AC outlet.

FUNCTION

NAMES AND

BASIC

CONNECTIONS

BASIC OPERATION

ADVANCED

CONNECTIONS

• Connect the shielded grounding wire (black) to the AM antenna GND terminal.

1.

Release the vinyl tie and take out the connection line.

4. Place the antenna on stable surface.

CONNECTING THE FM OUTDOOR ANTENNA

Notes:

SETUP

• Keep the antenna away from noise sources (neon signs, busy roads, etc.).

• Do not put the antenna close to power lines. Keep it well away from power lines, transformers, etc.

• To avoid the risk of lightning and electrical shock,

2. Bend the base part in the reverse direction.

grounding is necessary.

ADVANCED

OPERATION

CONNECTING THE AM OUTDOOR ANTENNA

3. Inser t the hook at the bottom of the loop part into the slot at the base part.

The outdoor antenna will be more effective if it is stretched horizontally above a window or outside.

Notes:

• Do not remove the AM loop antenna.

• To avoid the risk of lightning and electrical shock, grounding is necessary.

TROUBLESHOOTING

OTHERS

15

ENGLISH

.

NAMES AND

FUNCTION

BASIC OPERATION

AMP OPERATION

TURNING ON THE UNIT

CONNECTIONS

BASIC

BASIC OPERATION

1. Connect the AC power cable to the wall outlet. Turn the power on to other units connected to

2.

CONNECTIONS

ADVANCED

SETUP

OPERATION

ADVANCED

TROUBLESHOOTING

OTHERS

this unit.

Press the POWER ON/STANDBY button of

3.

this unit. Every time the button is pressed, the power to this unit toggles between on and standby.

To activate power using the remote controller,

press the AMP button, followed by the ON button and SOURCE ON/OFF button of the remote controller.

SELECTING AN INPUT SOURCE

Before you can listen to any input media, you must ﬁ rst select the input source on the unit.

Example : DVD

To select DVD, turn the INPUT SELECTOR knob on the front panel or press the DVD button on the remote controller two times in a row. After you have selected DVD, simply turn on the DVD player and play the DVD.

• As the input source is changed, the new input name will appear momentarily an OSD information on the video display. The input name will also appear in the display, on the front-panel.

• If you use the FUNCTION RENAME feature (see page 28) , the renamed name appears on the display.

• As the input is changed, this unit will automatically switch to the digital input, surround mode, attenuation, and night mode status which were entered during the conﬁ guration process for that source.

• When a video source is selected, the selected video signal is output from the MONITOR OUT terminal.

ADJUSTING THE MAIN VOLUME

Adjust the volume to a comfortable level using the VOLUME control knob on the front panel or VOLUME + / – buttons on the remote controller. To increase the volume, turn the VOLUME knob clockwise or press VOLUME + button on the remote controller, to decrease the volume, turn counterclockwise or press VOLUME – button on the remote controller.

Notes:

• The volume can be adjusted within the range of – ∞ and –71 to 18 dB, in steps of 1 dB.

•

However, when the channel level is set as described on page 35, if the volume for any channel is set at +1 dB or greater, the volume cannot be adjusted up to 18 dB.

(In this case the maximum volume adjustment range

is “18 dB - Maximum value of channel level)

ADJUSTING THE TONE (BASS & TREBLE) CONTROL

During a listening session you may wish to adjust the Bass and Treble Control to suit your listening tastes or room acoustics.

(Using the remote controller)

To

adjust the tone

To adjust the bass effect, press BASS + or BASS

–

button

. To adjust the treble effect, TREBLE + or TREBLE– button

.

Notes:

• The tone control function is unavailable for the Source Direct, Pure Direct, Headphone, Dolby Virtual Speaker mode, and 176.4/192kHz PCM.

• The Tone control function is not available when MDAX is being used.

• The tone control function is not available when ACOUSTIC EQ is being used.

• Additionally, tone control is not available during Dolby TrueHD, Dolby Digital Plus, or DTS-HD playback.

, press the AMP button.

TEMPORARILY TURNING OFF THE SOUND

To temporarily silence all speaker outputs such as when interrupted by a phone call, press the MUTE button on the remote controller. This will interrupt the output to all speakers and the head-phone jack, but it will not affect an y recording or dubbing that may be in progress. When the system is muted, the display will show “MUTE” . Press the MUTE button again to return to normal operation.

TUNER OPERATION

To operate the unit from the remote controller, press the TUNE button on the remote controller so that the tuner mode is engaged.

LISTENING TO THE TUNER

Frequency scan step for AM is selectable. Default setup is 10 kHz step, if your country’s standard is 9 kHz step, Press BAND button on the front panel or BAND button on the remote controller more than 5 seconds. Scan step will change .

Note:

•

Preset memory for the tuner will clear by changing this setup.

AUTO TUNING

1. 2.3.

1

3

2

(Using the unit)

Turn the INPUT SELECTOR knob to select

1.

“TUNER”.

Press the BAND button to select either FM or

2.

AM.

Press the 3 or 4 cursor buttons on the front

3.

Panel for more than 1 second to start the auto tuning function.

Automatic searching begins then stops when a

4.

station is tuned in.

16

ENGLISH

.

(Using the remote controller)

To select tuner, Press the TUNE button twice

1.

within two second on the remote controller.

Press the BAND button to select either FM or

2.

AM. Press and hold the TUNE 3 or 4 button for 1

3.

second or more.

4. Automatic searching begins then stops when a station is tuned in.

If tuning does not stop at the desired station, use to the “Manual tuning” oper ation.

MANUAL TUNING

1. 2.3.

1

3

2

(Using the unit)

Turn the INPUT SELECTOR knob to select

1.

“TUNER”.

Press the BAND button to select either FM or

2.

AM.

Press the 3 or 4 cursor buttons on the front

3.

Panel to select the desired station.

DIRECT FREQUENCY CALL

1

2 3

4

1. To select tuner, Press the TUNE button twice within two seconds on the remote controller.

Press the BAND button to select either FM or

2.

AM.

Press the F.DIRECT on the remote controller,

3.

display will show “FREQ----”. lnput your desired station’s, frequency with the

4.

ten numbered keypad on the remote

5.

The desired station will automatically be tuned.

controller

(FM) TUNING MODE (AUTO STEREO OR MONO)

When in the auto stereo mode, “AUTO” indicator will be illuminated on the display. The “ST” indicator is illuminated when a stereo broadcast is tuned in. At open frequencies, the noise is muted and the “TUNED” and “ST” indicators are not illuminated. If the signal is weak, it may be difﬁ cult to tune into the station in stereo. In such a case, Press the T-MODE button on the front panel or T.MODE button on the remote controller. “AUTO” indicator is not illuminated, if FM stereo broadcasts are received in monaural and the “ST” indicator is not illuminated. To return to auto stereo mode, Press the T-MODE

.

button on the front panel or T.MODE button on the remote controller again. “AUTO” indicator is illuminated the display.

FUNCTION

NAMES AND

BASIC

CONNECTIONS

BASIC OPERATION

ADVANCED

CONNECTIONS

SETUP

(Using the remote controller)

To select tuner, press the TUNE button twice

1.

within two seconds on the remote controller.

Press the BAND button to select either FM or

2.

AM.

Press the

3.

deseired station.

TUNE 3 or

4 button to tune in the

ADVANCED

OPERATION

TROUBLESHOOTING

OTHERS

17

ENGLISH

NAMES AND

FUNCTION

REMOTE CONTROLLER OPERATION

To control the unit by your remote controller , you have to select the device AMP or TUNER by pressing the SOURCE button. Please refer below for the details in AMP and TUNER mode .

AMP MODE

CONNECTIONS

BASIC

BASIC OPERATION

CONNECTIONS

ADVANCED

SETUP

OPERATION

ADVANCED

TROUBLESHOOTING

SOURCE ON/OFF Turns the SR5003 on and off POWER OFF Turns the SR5003 off POWER ON Turns the SR5003 on ZONE A/B Turns on or off ZONE A or ZONE B Z.SPKR Turns on or off ZONE Speaker A A/D Switches between the analog or digital inputs ATT Reduces the input level SPKR A/B Selects the speaker system

7.1 Selects the 7.1CH IN SOURCE Selects a particular source component AMP Select AMP mode of remote unit INPUT 3 / 4 Change the input selecter of SR5003 DISPLAY Changes the front display mode MUTE Decreases the sound temporarily SURR Selects the surround mode VOLUME+/- Adjusts the over all sound level TOP Back to the TOP of SETUP MENU INFO Displays the current setting on the monitor Cursor Moves the cursor for setting in "SETUP MENU" mode ENTER Conﬁ rms the setting in "SETUP MENU" mode MENU Enters the "SETUP MENU" EXIT Exits from SETUP MENU T.TONE Enters the test tone menu AUTO(1) Selects auto surround STEREO(2) Selects STEREO mode P.DIRECT(3) Selects the pure direct mode SLEEP(4) Sets the sleep timer function M-DAX(5) Selects the M-DAX mode EQ(6) Selects the EQ mode LIP SYNC(7) Selects the LIP SYNC mode NIGHT(8) Turns on or off NIGHT mode V-OFF(9) Turns on or off video output HT EQ(CL) Turns on or off HT-EQ mode CH SEL(0) Calls up CH LEVEL ADJUST and adjusts speaker levels or 7.1ch input

level TV POWER Turns the TV on and off TV INPUT Select the TV video input TREBLE-/+ Adjusts the tone control of high frequency sound BASS-/+ Adjusts the tone control of low frequency sound

TUNER MODE

ZONE A/B AMP function enabled Z.SPKR AMP function enabled A/D AMP function enabled ATT AMP function enabled SPKR A/B AMP function enabled

7.1 IN AMP function enabled SOURCE AMP function enabled AMP AMP function enabled INPUT 3 / 4 AMP function enabled DISPLAY AMP function enabled MUTE AMP function enabled SURR AMP function enabled VOLUME+/– AMP function enabled INFO Shows preset information TUNE 3 / 4 Tunes a frequency station up and down PRESET + 2/– 1 Selects a preset station up and down EXIT/MEMO Enters the tuner preset memory numbers T.TONE AMP function enabled T.MODE Selects the auto stereo mode or mono mode P.SCAN Starts preset scan BAND Selects a radio band T.DISP F.DIRECT Selects the “Frequency direct input” P.LOCK Select the parental lock mode 0-9 Inputs the numeric CL Clears the inputting TV POWER Turns the TV on and off TV INPUT Select the TV video input

• The remote controller dose not have the PRESET code library for this device.

Selects the display mode in XM Satellite Radio and SIRIUS Satellite Radio

OTHERS

18

AD VANCED CONNECTIONS

L

R

INPUT 3

(

VCR

)

INPUT 2

(

DVD

)

INPUT 1

(

TV

)

FM

(

Ω

)

GNDAMAM

ANTENNA

SR

C

SBR

SL

SBL

L

PRE OUT

ON

RS-232C

SPEAKER C

OFF

OUTPUT

FRONT A

FRONT B

R

L

IN

TV

DSS

VCR

DVD

OUT

IN

7.1CH INPUT

(

AUX 2

)

C

L

SBL

SBR

ZONE A

ESPEAKER SYSTEMS

FRONT A OR B,CENTER, SURR,SURR BACK : 6-8 OHMS FRONT A + B : 8 OHMS

SBL

SBR

R

L

C

7.1CH INPUT

(

AUX 2

)

L

R

INPUT 3

(

VCR

)

INPUT 2

(

DVD

)

INPUT 1

(

TV

)

FM

(

Ω

)

GNDAMAM

ANTENNA

SR

C

SBR

SL

SBL

L

PRE OUT

ON

RS-232C

SPEAKER C

OFF

OUTPUT

FRONT A

FRONT B

R

L

IN

TV

DSS

VCR

DVD

OUT

IN

7.1CH INPUT

(

AUX 2

)

C

L

SBL

SBR

ZONE A

ESPEAKER SYSTEMS

FRONT A OR B,CENTER, SURR,SURR BACK : 6-8 OHMS FRONT A + B : 8 OHMS

8CH POWER AMPLIFIER MM8003

POWER ON/OFF

STANDBY

SR

C

SBR

SL

SBL

L

PRE OUT

ENGLISH

CONNECTING MULTI CHANNEL AUDIO COMPONENTS

The 7.1CH INPUT jacks are for multichannel audio source such as a Super Audio CD multichannel player, DVD audio player or external decoder. If you use these jacks, s witch on the 7.1CH INPUT and set the 7.1CH INPUT le v el b y using the SETUP MAIN MENU. See page 27.

L R LR

R L R L R L

L R

FRONT SURR.

DVD Audio play er

or

Super Audio CD

Multi channel player

SURR.

BACK

CENTER

SUB

WOOFER

L R

FM

(

)

GND

7575Ω

(

)

INPUT 1

TV

SLSLC

L

LLSLSLCCSBL

L

R

RRSRSRSWSWSBR

(

)

(

)

7.1CH INPUT

AUX 2

7.1CH INPUT

AUX 2

RS-232C

SL

L

RRSR

PRE OUT

INPUT 2

C

SPEAKER C

ON

OFF

C

SWSWSBR

ANTENNA

(

)

INPUT 3

DVD

SBL

ZONE A

OUT

SBL

FRONT A OR B,CENTER, SURR,SURR BACK : 6-8 OH FRONT A + B : 8 OHMS

(

)

VCR

TV

RRL

FRONT A

OUTPUT

DSS

VCR

DVD

OUT

IN

LLR

FRONT B

SPEAK

CONNECTING AN EXTERNAL POWER AMPLIFIER

The PREOUT jacks are for connecting external power ampliﬁ ers. Be sure to connect each speaker to the corresponding external power ampliﬁ er.

R L R L R L

FM

(

)

GND

7575Ω

INPUT 1

L

R

RRSRSRSWSWSBR

(

AUX 2

L

RRSR

RS-232C

ANTENNA

(

)

INPUT 3

DVD

SBL

ZONE A

OUT

SBL

FRONT A OR B,CENTER, SURR,SURR BACK : 6-8 OH FRONT A + B : 8 OHMS

)

VCR

TV

RRL

FRONT A

OUTPUT

DSS

VCR

DVD

OUT

IN

LLR

FRONT B

SPEAK

L R

Power

Amplifer

FRONT SURR.

(

)

INPUT 2

TV

SLSLC

)

7.1CH INPUT

SPEAKER C

ON

OFF

C

SL

C

SL

SWSWSBR

PRE OUT

FUNCTION

NAMES AND

BASIC

CONNECTIONS

BASIC OPERATION

CENTER

SURR. BACK

8CH POWER AMPLIFIER MM8003

STANDBY

POWER ON/OFF

ADVANCED

CONNECTIONS

SETUP

Front

RL

RL RL

Left

Surround Left

Surround Back Left

Center

Front Right

Surround

Right

Surround Back Right

Powered

Subwoofer

ADVANCED

OPERATION

TROUBLESHOOTING

OTHERS

19

ENGLISH

MODEL NO. SR5003

SWITCHED

1.25A 150W

UNSWITCHED

1.25A 150W

AC IN

SIRIUS

AC OUTLETS 120V 60Hz

L

OUTPUT 2

OUTPUT 1

INPUT 2

(

DVD

)

INPUT 3

(

VCR

)

INPUT 1

(

TV

)

COMPONENT

VIDEO

MONITOR OUT

C

R

/

P

R

C

B

/

P

B

Y

C

R

/

P

R

C

B

/

P

B

Y

C

R

/

P

R

C

B

/

P

B

Y

VCR OUT

VCR IN

(

3

)

(

2

)

DSS

(

4

)

REMOTE CONT.

IN

OUT

3

DIGITAL IN

5

2

REC/ZONE B

DIGITAL

DC OUT

OUT

FLASHER IN

REMOTE CONT.

IN

OUT

MODEL NO. SR5003

SWITCHED

1.25A 150W

UNSWITCHED

1.25A 150W

AC IN

SIRIUS

AC OUTLETS 120V 60Hz

R

L

R

AUDIO

OUTPUT 2

OUTPUT 1

INPUT 2

(

DVD

)

INPUT 3

(

VCR

)

INPUT 1

(

TV

)

COMPONENT

VIDEO

MONITOR OUT

C

R

/

P

R

C

B

/

P

B

Y

C

R

/

P

R

C

B

/

P

B

Y

C

R

/

P

R

C

B

/

P

B

Y

VCR OUT

VCR IN

(

3

)

TV

(

1

)

DVD

(

2

)

DSS

(

4

)

S-VIDEO

VIDEO

INPUT 3

(

VCR

)

INPUT 2

(

DVD

)

INPUT 1

(

TV

)

FM

(

Ω

)

GNDAMAM

ANTENNA

SR

C

SBR

SL

SBL

L

PRE OUT

ON

RS-232C

SPEAKER C

OFF

OUTPUT

CENTER

SURROUND

FRONT A

FRONT B

SURROUND BACK

SPEAKER C/

ZONE SPEAKER A

R

L

CD/CDR

OUTININ

TAPE

TV

DSS

VCR

DVD

OUT

IN

REMOTE CONT.

IN

OUT

3

1

4

DIGITAL IN

5

2

REC/ZONE B

DIGITAL

DC OUT

FLASHER IN

7.1CH INPUT

(

AUX 2

)

C

L

SBL

SBR

ZONE A

SPEAKER SYSTEMS

FRONT A OR B,CENTER, SURR,SURR BACK : 6-8 OHMS FRONT A + B : 8 OHMS

ON

SPEAKER C

OFF

R

L

R

CENTER

SURROUND

FRONT A

FRONT B

SURROUND BACK

SPEAKER C/

ZONE SPEAKER A

SPEAKER SYSTEMS

FRONT A OR B,CENTER, SURR,SURR BACK : 6-8 OHMS FRONT A + B : 8 OHMS

ON

SPEAKER C

OFF

NAMES AND

FUNCTION

CONNECTING FOR SPEAKER C USE (BI-AMP CONNECTION)

A bi-amp connection is possible with speakers that hav e tw o sets of inputs (for treble and bass). This allows you to drive the treble and bass units with separate channel amps, which enables better sound quality. Connect the speakers as shown in the ﬁ gure. Set the SPEAKER C selector switch on the rear panel to ON.

Notes:

CONNECTIONS

• If incorrectly connected, a protective circuit in the unit will trip and set the unit to standby. (The STANDBY

BASIC

BASIC OPERATION

CONNECTIONS

ADVANCED

indicator will ﬂ ash.) In such case, recheck the connections between the speakers and the unit.

• Turn power to the unit off before changing the setting of the SPEAKER C selector switch.

(

)

INPUT 1

SWITCHED

TV

C

R

/

P

R

C

B

/

P

B

Y

(

)

INPUT 2

DVD

SIRIUS

IN

FM

(

)

GND

7575Ω

(

)

INPUT 1

TV

SLSLC

L

R

RRSRSRSWSWSBR

(

)

7.1CH INPUT

AUX 2

RS-232C

SL

L

RRSR

PRE OUT

SPEAKER C

ON

OFF

INPUT 2

SPEAKER C

OFF

C

SWSWSBR

ANTENNA

(

DVD

SBL

ON

SBL

(

)

INPUT 3

VCR

TV

DVD

ZONE A

OUT

RRL

FRONT A

FRONT A OR B,CENTER, SURR,SURR BACK : 6-8 OHMS

FRONT A + B : 8 OHMS

R

SURROUND

VIDEO

S-VIDEO

(

)

(

)

TV

1

AUDIO

CD/CDR

OUT

L

DVD

2

4

5

1

2

OUT

RRL

CENTER

SURROUND BACK

CENTER

SURROUND BACK

SPEAKER C/

ZONE SPEAKER A

VCR IN

DIGITAL IN

(

)

DSS

4

(

)

MONITOR OUT

VCR OUT

3

DIGITAL

REMOTE CONT.

FLASHER IN

REC/ZONE B

3

DC OUT

OUT

AC OUTLETS

120V 60Hz

UNSWITCHED

1.25A 150W

OUTPUT

TAPE

DSS

VCR

OUT

IN

LLR

FRONT B

SPEAKER SYSTEMS

INPUT 3

C

R

/

P

R

C

B

/

P

B

Y

OUTPUT 1

MODEL NO. SR5003

AC IN

CONNECTING THE REMOTE CONTROL JACKS

(

C

IN

B

/

P

INPUT 3

B

VCR

C

R

/

P

R

MODEL NO. SR5003

)

COMPONENT

VIDEO

C

R

/

P

R

C

B

/

P

B

Y

OUTPUT 2

DVD playerCD recorder

EXTERNAL INTERNAL

2

RC OUT

OPTION

REMOTE

CONTROL

IN

OUT

CD player

EXTERNAL INTERNAL

(

)

INPUT 1

TV

(

)

DSS

4

(

)

(

)

VCR IN

D

2

DIGITAL IN

5

2

(

)

VCR

COMPONENT

VIDEO

C

R

/

P

R

C

B

/

P

B

Y

OUTPUT 2

L

UND BACK

AKER C/

PEAKER A

MONITOR OUT

VCR OUT

3

DIGITAL

REC/ZONE B

3

OUT

FLASHER IN

DC OUT

REMOTE CONT.

OUT

AC OUTLETS 120V 60Hz

UNSWITCHED

1.25A 150W

SWITCHED

1.25A 150W

Y

INPUT 2

IN

Y

C

R

/

P

R

C

B

/

P

B

(

)

OUTPUT 1

DVD

SIRIUS

AC IN

1

REMOTE CONTROL

IN

OUT

EXTERNAL INTERNAL

REMOTE

CONTROL

OUT

SETUP

OPERATION

ADVANCED

TROUBLESHOOTING

Note:

• You can use surround back speaker terminals as ZONE SPEAKER A. terminals or SPEAKER C terminal when you are not using surround back speakers.

OTHERS

20

RIGHT

SPEAKER

q

You can control other Marantz products through this unit with the remote controller by connecting the REMOTE CONTROL terminals on each unit. The signal transmitted from the remote controller

w

Whenever e xternal infrared sensors or similar devices are connected to RC-5 IN of the unit, be sure to always disable operation of the infr ared sensor on the unit by using the following procedure.

is received by the remote sensor on this unit. Then

LEFT SPEAKER

the signal is sent to the connected device through this terminal. Therefore you need to aim the remote control only at the unit. Also, if a Marantz power ampliﬁ er (some models excluded) is connected to one of these terminals, the power ampliﬁ er’s, power switch is synchronized with this unit’s power switch.

Set the REMOTE CONTROL SWITCH on the back of other units (not the SR5003) to “EXT.” (EXTERNAL) to use this feature.

1. Hold down the SURROUND MODE button and the MENU button on the front panel at the same time for ﬁ ve seconds.

The setting “IR=ENABLE” is shown on the FL

2.

DISPLAY.

Press the CURSOR buttons (1, 2) to change

3.

this to “IR=DISABLE”.

Press the ENTER button. Once this setting

4.

is made, the infrared sensor on the unit is disabled.

Note:

• Be sure to set to “IR=ENABLE” when external infrared sensors or similar devices are not connected. Otherwise, the unit will be unable to receive remote control commands.

To restore the original setting, perform steps 1

5.

to 4 to set to “IR=ENABLE”.

MODEL NO. SR5003

SWITCHED

1.25A 150W

UNSWITCHED

1.25A 150W

AC IN

SIRIUS

AC OUTLETS 120V 60Hz

R

L

R

AUDIO

OUTPUT 2

OUTPUT 1

INPUT 2

(

DVD

)

INPUT 3

(

VCR

)

INPUT 1

(

TV

)

COMPONENT

VIDEO

MONITOR OUT

C

R

/

P

R

C

B

/

P

B

Y

C

R

/

P

R

C

B

/

P

B

Y

C

R

/

P

R

C

B

/

P

B

Y

VCR OUT

VCR IN

(

3

)

TV

(

1

)

DVD

(

2

)

DSS

(

4

)

S-VIDEO

VIDEO

INPUT 3

(

VCR

)

INPUT 2

(

DVD

)

INPUT 1

(

TV

)

FM

(

Ω

)

GNDAMAM

ANTENNA

SR

C

SBR

SBL

L

PRE OUT

ON

RS-232C

SPEAKER C

OFF

OUTPUT

CENTER

SURROUND

FRONT A

FRONT B

SURROUND BACK

SPEAKER C/

ZONE SPEAKER A

R

L

CD/CDR

OUTININ

TAPE

TV

DSS

VCR

DVD

OUT

IN

REMOTE CONT.

IN

OUT

3

1

4

DIGITAL IN

5

2

REC/ZONE B

DIGITAL

DC OUT

FLASHER IN

7.1CH INPUT

(

AUX 2

)

C

L

SBL

SBR

ZONE A

SPEAKER SYSTEMS

FRONT A OR B,CENTER, SURR,SURR BACK : 6-8 OHMS FRONT A + B : 8 OHMS

L

SURROUND BACK

SPEAKER C/

ZONE SPEAKER A

REMOTE CONT.

IN

REC/ZONE B

DIGITAL

FLASHER IN

ZONE A

OUT

CONNECTION FOR ANOTHER ZONE

As shown in the diagram, a play er connected to this unit in another ZONE can be used to play music and movies when used in combination with an amp from Marantz or other manufacturer.

ENGLISH

FUNCTION

NAMES AND

RIGHT

SPEAKER

RX3001

RC3001

(ZONE speaker A)

IR OUTPUT

LEFT

SPEAKER

ZONE

LEFT

SPEAKER

MAIN AMP

(For ZONE)

ZONE

RIGHT

SPEAKER

L R

FRONT

OPT IN

REMOTE OUT

BASIC

CONNECTIONS

ES7001

LR

BASIC OPERATION

R L

(

OUTPUT 1

)

INPUT 3

VCR

COMPONENT

VIDEO

C

R

/

P

R

C

B

/

P

B

Y

C

R

/

P

R

C

B

/

P

B

OUTPUT 2

RC101

MODEL NO. SR5003

ZONE B

(

)

INPUT 1

TAPE

OUT

R

SURROUND

VIDEO

S-VIDEO

(

)

(

)

TV

1

AUDIO

CD/CDR

L

DVD

2

4

5

1

2

OUT

RRL

CENTER

SURROUND BACK

SPEAKER C/

ZONE SPEAKER A

VCR IN

DIGITAL IN

(

)

DSS

4

(

)

MONITOR OUT

VCR OUT

3

DIGITAL

FLASHER IN

DIGITAL

FLASHER IN

REC/ZONE B

3

DC OUT

OUT

FM

(

)

GND

7575Ω

ANTENNA

(

)

(

)

(

)

INPUT 3

DVD

SBL

ZONE A

OUT

ON

VCR

OUTPUT

TV

DVD

IN

RRL

FRONT A

FRONT A OR B,CENTER, SURR,SURR BACK : 6-8 OHMS FRONT A + B : 8 OHMS

DSS

VCR

OUT

LLR

FRONT B

SPEAKER SYSTEMS

INPUT 2

INPUT 1

TV

SLSLC

L

R

RRSRSRSWSWSBR

(

)

7.1CH INPUT

AUX 2

RS-232C

OFF

SLSLSBL

L

RRSR

SWSWSBR

PRE OUT

SPEAKER C

C

REMOTE CONT.

OUT

AC OUTLETS 120V 60Hz

UNSWITCHED

1.25A 150W

SWITCHED

1.25A 150W

Y

IN

INPUT 2

TV

C

B

/

P

B

(

DVD

Y

C

R

/

P

R

)

SIRIUS

AC IN

ADVANCED

CONNECTIONS

SETUP

ADVANCED

OPERATION

If Surround back speakers or SPEAKER C are not being used, the Surround Back Speaker terminals can be used for the ZONE SPEAKER A terminals.

ZONE A

TROUBLESHOOTING

OTHERS

21

ENGLISH

MODEL NO. SR5003

SWITCHED

1.25A 150W

UNSWITCHED

1.25A 150W

AC IN

SIRIUS

AC OUTLETS

120V 60Hz

L

OUTPUT 2

OUTPUT 1

INPUT 2

(

DVD

)

INPUT 3

(

VCR

)

INPUT 1

(

TV

)

COMPONENT

VIDEO

MONITOR OUT

C

R

/

P

R

C

B

/

P

B

Y

C

R

/

P

R

C

B

/

P

B

Y

C

R

/

P

R

C

B

/

P

B

Y

VCR OUT

VCR IN

(

3

)

TV

(

1

)

DVD

(

2

)

DSS

(

4

)

S-VIDEO

VIDEO

CENTER

SURROUND BACK

SPEAKER C/

ZONE SPEAKER A

OUT

REMOTE CONT.

IN

OUT

3

1

4

DIGITAL IN

5

2

REC/ZONE B

DIGITAL

DC OUT

FLASHER IN

SIRIUS

XM

NAMES AND

FUNCTION

CONNECTING THE SATELLITE RADIO

Subscriptions are required in order to listen to both XM Satellite Radio and SIRIUS Satellite Radio. F or details on XM Satellite Radio, see page 49. For details on SIRIUS Satellite Radio, see page 54.

XMXMXM

CONNECTIONS

BASIC

Y

C

OUTPUT 1

B

/

P

INPUT 3

B

(

VCR

C

R

/

P

R

MODEL NO. SR5003

BASIC OPERATION

CONNECTIONS

ADVANCED

(

)

INPUT 1

REMOTE CONT.

OUT

AC OUTLETS 120V 60Hz

UNSWITCHED

1.25A 150W

SWITCHED

1.25A 150W

TV

C

R

/

P

R

C

B

/

P

B

Y

(

)

INPUT 2

DVD

SIRIUS

IN

AC IN

VIDEO

S-VIDEO

(

)

(

)

TV

1

DIO

DVD

CDR

2

4

5

1

2

OUT

RRL

CENTER

SURROUND BACK

SPEAKER C/

ZONE SPEAKER A

VCR IN

DIGITAL IN

(

)

DSS

4

(

)

MONITOR OUT

VCR OUT

3

DIGITAL

FLASHER IN

REC/ZONE B

3

DC OUT

OUT

Antenna

SETUP

TM

OPERATION

ADVANCED

SiriusConnect

HOME Tuner

)

COMPONENT

VIDEO

C

B

/

P

Y

OUTPUT 2

adapter

XM SATELLITE RADIO

• Plug the XM Mini-Tuner and Home Dock into XM terminal on the rear panel.

• Position the XM antenna near a south-facing window to receive the best signal. When making connections, also refer to the operating instructions of the XM Mini-Tuner and Home Dock.

Note:

This unit does not support the XM CNP-1000. See page 67.

SIRIUS SATELLITE RADIO

• Plug the SiriusConnectTM Home Tuner, Antenna and AC adapter into SIRIUS terminal on the rear panel.

C

R

/

P

R

B

AC

• Position the SIRIUS antenna f or a consistent satellite signal, the antenna m ust be positioned correctly. Use the following map to determine which area you are in and position the antenna accordingly.

(US) (Canada)

SKY

EAST

HORIZON

NORTH

1

WEST

5

2

4

3

SOUTH

AREA ANTENNA AIMING DIRECTION

AREA 1 Aim the antenna EAST or NORTHEAST

AREA 2 Aim the antenna NORTH or NORTHEAST

AREA 3 Aim the antenna NORTH or NORTHWEST

AREA 4 Aim the antenna WEST or NORTHWEST

AREA 5

Aim the antenna STRAIGHT UP at the sky (may require outdoor placement)

SKY

EAST

HORIZON

NORTH

WEST

1

2

3

SOUTH

AREA ANTENNA AIMING DIRECTION

AREA 1 Aim the antenna EAST or SOUTHEAST

AREA 2 Aim the antenna SOUTH or STRAIGHT UP at

the sky (may require outdoor placement)

AREA 3 Aim the antenna WEST or SOUTHWEST

TROUBLESHOOTING

OTHERS

22

Marantz SR5003 User Guide

Specifications and Main Features

Frequently Asked Questions

User Manual