English
4
CD TEXT
TEXT
FOREWORD
This section must be read carefully before any connection is made to the
mains supply.
WARNINGS
Do not expose the equipment to rain or moisture.
Do not remove the cover from the equipment.
Do not insert anything into the equipment through the ventilation
holes.
Do not handle the mains lead with wet hands.
CE marking
This product is in conformity with the EMC directive
and low-voltage directive.
EQUIPMENT MAINS WORKING SETTING
Your Marantz product complies with the household power and safety
requirements in your area.
“/N”, “/T” Version product can be powered by 230 V AC only.
IMPORTANT: (FOR /T version only)
This apparatus is fitted with an approved moulded 13 Amp plug. To
change a fuse in this type of plug proceed as follows:
1. Remove fuse cover and fuse.
2. Fix new fuse which should be a BS1362 5A, A.S.T.A. or BSI approved
type.
3. Refit the fuse cover.
If the fitted plug is not suitable for your socket outlets, it should be cut off
and an appropriate plug fitted in its place.
If the mains plug contains a fuse, this should have a value of 5A. If a plug
without a fuse is used, the fuse at the distribution board should not be
greater than 5A.
NOTE : The severed plug must be destroyed to avoid a possible shock
hazard should it be inserted into a 13A socket elsewhere.
HOW TO CONNECT A PLUG
The wires in the mains lead are coloured in accordance with the following
code:
BLUE—”NEUTRAL” (“N”)
BROWN—”LIVE” (“L”)
1. The BLUE wire must be connected to the terminal which is marked with
the letter “N” or coloured BLACK.
2. The BROWN wire must be connected to the terminal which is marked
with the letter “L” or coloured RED.
3. Do not connect either wires to the earth terminal in the plug which is
marked by the letter “E” or by the safety earth symbol
or coloured
green or green-and-yellow.
Before replacing the plug cover, make certain that the cord grip is
clamped over the sheath of the lead — not simply over the two wires.
COPYRIGHT
Recording and playback of some material may require permission. For
further information refer to the following:
– Copyright Act 1956
– Dramatic and Musical Performers Act 1958
– Performers Protection Acts 1963, and 1972
– Any subsequent statutory enactments and orders
ABOUT THIS USER’S GUIDE
Refer to the figures on the pages at the back of this user’s guide. The
callout numbers on the figures correspond to those found in the text.
• Some of the operations described in this user’s guide can only be
operated from the remote control unit. In the description of controls,
the names of the buttons which are available on both the main unit and
the remote control unit are enclosed in
, and the names of the
buttons which are available only on the remote control unit are
enclosed in
.
(The ⁄1
PEAK SEARCH
button is located only on the main unit.)
PRECAUTIONS
The following precautions should be taken when operating the equipment.
GENERAL PRECAUTIONS
When installing the equipment ensure that:
– the ventilation holes are not covered.
– air is allowed to circulate freely around the equipment.
– it is placed on a vibration-free surface.
– it will not be exposed to excessive heat, cold, moisture or dust.
– it will not be exposed to direct sunlight.
– it will not be exposed to electrostatic discharges.
In addition, never place heavy objects on the equipment.
If a foreign object or water does enter the equipment, contact your
nearest dealer or service center.
Do not pull out the plug by pulling on the mains lead; grasp the plug.
It is advisable when leaving the house, or during a thunderstorm, to
disconnect the equipment from the mains supply.
FEATURES
• CD-TEXT compatibility.
• CD-RW (ReWritable) playback capability.
• Latest VAM1201 pickup mechanism.
• A double differential circuit which utilizes two D type 2-channel D/A
converters is used.
• High audio quality parts including the MARANTZ-original HDAM
circuitry.
• Highly rigid, stylish design with extensive use of aluminum front mask.
English
5
COMPACT DISCS
The glossy side shining like a rainbow is the front side of the disc, and
the side on which the label is printed is the back.
Unlike conventional turntables for playing analog discs, the CD6000/
CD6000OSE Compact Disc Player reads the information recorded on
the disc from underneath without contacting it using a beam of laser light.
Therefore, the performance of a compact disc will not degrade like
conventional analog records.
Handle discs carefully so as not to damage or scratch the front side.
To protect the disc, avoid placing it in the following locations:
– In direct sunlight or near a source of heat like a heater.
– In a place which is damp or dirty.
– In a place which could be exposed to rain, such as near a window.
Always keep the disc surface clean.
Up to six billion data units are recorded on the front side of the disc.
When cleaning the disc surface, always be sure to use a special
compact disc cleaner and wipe as shown below.
• Do not use conventional record cleaner for analog records, as this will
adversely affect the disc surface.
Store discs properly by placing them in their disc cases.
• Do not attach a piece of paper or sticker on the label side of disc.
When a disc has a piece of plastic tape or rental CD label with paste
protruded from the edge or when a disc has a trace of such a sticky
object, do not attempt to play the disc. If such a disc is played on the
CD player, impossibility of taking out the disc or other malfunction may
result.
• Do not use a disc with a special shape.
Do not attempt to play a disc with a special shape such as a heartshaped disc or octagonal disc. Otherwise the equipment malfunction
may result.
Wipe in a radial direction. Do not wipe in circumferential direction.
About CD-TEXT
The CD-TEXT is a new type of music CD featuring the recording of
character information on the performer names, album name, track
names, etc., in addition to the audio information contained in music CD.
The character information is recorded in an area which has not been
utilized by previous music CDs. This means that the CD-TEXT discs can
be played back in the same way as ordinary music CD discs on any CD
player and that a CD-TEXT compatible player such as this unit can view
the character information in them as well as the audio.
This unit detects the CD-TEXT compatibility of each disc automatically
and displays the result in the display panel.
By operating the provided remote control unit, the display can show the
character information including the album name, track names, performer names, verse writer names, music composer names, arranger
names, message and music genre. However, note that the content of the
character information is variable depending on discs.
* For detailed operating procedures for displaying the character infor-
mation in the CD-TEXT, read the description in the main text of this
manual.
The display of this unit can display up to 12 characters at a time. If the
character information in a disc is longer, the characters are scrolled from
the left to the right on the display.
* Scrolling refers to a method of displaying characters by moving them.
This unit is capable of smooth scrolling by feeding characters bit by
bit.
Some of the CD-TEXT compatible discs also contains the recording of
the highlight sections of its tracks. This unit is capable of playing only the
highlight sections one after another, and this feature is referred to as
HIGHLIGHT SCAN.
Playing CD-RW discs
This unit can play back the CD-RW (ReWritable) discs as well as ordinary
music CD and CD-R (Recordable) discs.
* The CD-R and CD-RW discs should contain properly-recorded TOC
information so that they can be played back. With the CD recorder
system, writing the TOC information in a disc is referred to as finalizing
the disc. A disc cannot be recognized as a CD disc and played back
unless it has been finalized properly. For details, please read the
instruction manual provided with a CD recorder.
* TOC stands for Table Of Contents and contains information such as
the total number of tracks and total playing time of the disc.
* This unit can play only the discs recorded in the CD-DA format
designed for music reproduction. Do not attempt to play a disc
containing other data, such as a CD-ROM for PCs, on this unit.
* As the playback of a CD-RW disc necessitates partial change of the
player setup, it may take longer time for reading the TOC information
than when a music CD or CD-R disc is played.
TEXT 1 2
TTL TTL TIME
34 56 78 91011121314151617181920
Lights up when the loaded disc is CD-TEXT compatible.
Main unit display
English
6
CONTROLS, CONNECTIONS
AND INDICATORS
Please read the following instructions referring to the illustration on page
122.
FRONT
zz
zz
z
POWER switch
Press to switch power ON, and press again to switch OFF.
xx
xx
x
DISC TRAY
Place a disc with the label side up.
cc
cc
c
REMOTE SENSOR
This window receives signals transmitted from the remote control unit.
vv
vv
v
Display
Shows information such as the power ON/OFF state, track number,
playing time and current operation mode.
qq
qq
q
TIME/TEXT information
Shows the time information when an ordinary music CD is played,
and shows the text information when a CD-TEXT compatible disc
is played.
ww
ww
w
TEXT (CD-TEXT) indicator
Lights up when a CD-TEXT compatible disc is loaded.
ee
ee
e
Track number indicator
When a disc is placed on the tray and the tray is closed, the TOC*
is read and the numbers of all the tracks on the disc are displayed
“
” lights up if there are more than 20 tracks on the disc. In
program mode only the track numbers of the programmed tracks
light up.
The track numbers go out in turn as each track finishes playing.
* TOC is the disc’s “Table Of Contents” and contains non-audio
data such as the track numbers and playing times of all the tracks
on the disc.
rr
rr
r
Output level indicator
Shows the analog output level as a relative reference.
tt
tt
t
DISC indicator
Blinks during TOC readout.
yy
yy
y
TTL (Total) indicator
Lights up when the total number of tracks in a disc is displayed.
uu
uu
u
RNDM (Random) indicator
Lights up in the random play mode.
ii
ii
i
PROG (Program) indicator
Lights up in the programming or delete programming mode.
oo
oo
o
TRK (Track) indicator
Lights up when the track number being played is displayed.
!0!0
!0!0
!0
EDIT indicator
Lights up when the player is in edit mode.
!1!1
!1!1
!1
A-B indicators
Both indicators light up in the A-B repeat mode or one of them
lights up during playback of tape side A or B in the edit mode.
!2!2
!2!2
!2
INDX (Index) indicator
Lights up when the index number being played is displayed.
!3!3
!3!3
!3
RPT (Repeat) indicators
RPT: Lights up during all-track repeat mode, which plays all the
tracks on the disc repeatedly. Also lights up during program
repeat mode, which plays all the programmed tracks repeatedly.
RPT 1: Lights up during 1-track repeat mode, which repeatedly
plays a single track repeatedly.
!4!4
!4!4
!4
PEAK indicator
Lights up during peak search, and flashes during playback of the
peak.
!5!5
!5!5
!5
(Pause) indicator
Light up in the pause mode.
!6!6
!6!6
!6
TTL (TOTAL) indicator
Indicates the remaining playing thme of the entire disc. In program
mode, this indicator shows the remaining playing of the current
program.
!7!7
!7!7
!7
(Play) indicator
Light up during CD playback.
!8!8
!8!8
!8
TIME indicator
Lights up in the time display mode.
bb
bb
b
PHONES Jack
Jack for connecting headphones.
nn
nn
n
EDIT button
Press to engage the editing function, which helps record a disc onto a
tape by playing the tracks according to the tape length and leaving a
non-recorded blank of 4 seconds between every track.
mm
mm
m
, (Track Previous/Next) buttons
When the button is pressed during playback, play re-starts at
the beginning of the current or a previous track. When the
button
is pressed, play re-starts at the beginning of the next or a subsequent
track.
Hold down
or button to find a particular passage in a
backward or forward direction.
The selected track number is shown on the display.
These buttons can also be used to select a desired track from which to
start playback.
These buttons are also used in program mode to select tracks for
programming.
,,
,,
,
STOP
button
Press to stop playback. This button is also used for deleting a program.
..
..
.
PAUSE
button
Press to interrupt playback temporarily. The indicator lights up during
pause. When pressed again, the indicator goes out and playback
resumes from the same position.
⁄0⁄0
⁄0⁄0
⁄0
PLAY
button
Press to start playback.
⁄1⁄1
⁄1⁄1
⁄1
PEAK SEARCH
button
When the
PEAK SEARCH
button is pressed, searching for the loudest
passage (peak) on a CD or in a program.
⁄2⁄2
⁄2⁄2
⁄2
OPEN/CLOSE
button
Pressing the
OPEN/CLOSE
button opens the disc tray. Place a compact
disc on the tray ith the label side facing up. Gently press the front of the
disc tray to close.
⁄3⁄3
⁄3⁄3
⁄3
SCROLL/(RECALL) button
Press this button to display the programmed track numbers and program
numbers (the order the tracks are programmed) in sequence.
If the loaded disc is a CD-TEXT disc, press this button while the text
information is displayed to scroll the characters.
⁄4⁄4
⁄4⁄4
⁄4
CD-TEXT. button
When playing a CD-TEXT disc, press this button to switch the time
display to the text information display.
* If this button is pressed when the loaded disc is not a CD-TEXT
compatible disc, the display shows "No Text" then returns to the time
display.
!3
RNDM PROG EDIT A – B RPT 1
DISC
TEXT 1 2
TTL TRK INDX PEAK TTL TIME
34 56 78 91011121314151617181920
r
o
t y u i !0 !1
!2 !6 !8
!4 !5 !7
qw e
English
7
USING THE REMOTE CONTROL UNIT
1. Remote control
Operate the remote control unit (RC6000CD) within a distance of approx.
5 m from the infrared signal reception window (remote sensor) on the
front of the CD player.
Remote control operation may not be possible if the remote control unit’s
transmitter is not pointing in the direction of the remote sensor or if there
is an obstruction between the transmitter and the remote sensor.
Remote control operating range
2. Loading batteries
Batteries in this remote control unit have a life of approximately 1 year
under normal operating conditions. If the remote control unit is not going
to be used for an extended period of time, remove the batteries. Also, if
you notice that the batteries are starting to run down, replace them as
soon as possible.
REAR
AA
AA
A
ANALOG OUTPUT jacks
Connect to the CD or AUX input jacks of a preamplifier.
BB
BB
B
DIGITAL OUTPUT OPTICAL output jack
The digital signal can transmitted in the form of light through an optical
fiber cable and photocoupler. The optical signal transmission features
low signal loss due to cables and complete isolation of the ground loop
so that the very high quality can be reproduced without any digital noise
Connection method:
Connect this jack to aD/A converter, digital sound processor or an
amplifier equipped with a Digital Optical input jack. Remove the caps
from the DIGITAL OUTPUT OPTICAL jack and the Optical input jack of
the connected component and connect the two jacks through an optical
fiber cable.
* Do not bend the optical fiber cable.
* Leave the cap attached when the OPTICAL jack is not used.
CC
CC
C
DIGITAL OUTPUT COAXIAL output jack
By connecting this jack to a digital audio component (D/A converter,
digital sound processor, etc.), digital signals from compact discs can be
transmitted directly from the player without first being converted to
analog.
DD
DD
D
REMOTE CONTROL IN/OUT jacks
By connecting this CD player to another Marantz audio component
using a D-BUS remote control cable, you can operate the components
remotely as a single system.
• When connecting to a component with a remote sensor, connect the
REMOTE CONTROL IN jack of this unit to the REMOTE CONTROL
OUT jack of the component with the remote sensor.
• When connecting to a component which is not equipped with a remote
sensor, connect the component to the REMOTE CONTROL OUT jack
of this unit.
For the D-BUS cable connection, use a commercially available RCAtype pin lead.
• By connecting this CD player to a Marantz auto reverse cassette deck
(such as the SD4050, SD555), automatic recording from the CD
player to the cassette deck can be carried out.
EE
EE
E
REMOTE switch
When using this unit independently, set this switch to INTERNAL. When
using this unit in a system incorporating a Marantz tuner or timer
equipped with a remote sensor, set the switch to EXTERNAL.
NOTE
Always set this switch to INTERNAL unless the unit is connected with
other MARANTZ equipment through a system connection. When this
switch is set to EXTERNAL, the main unit cannot be controlled from
the provided remote control unit.
FF
FF
F
AC POWER SOURCE CONNECTION
With the POWER switch set to the OFF position, plug the mains lead into
a mains outlet providing the right voltage.
60°
Approx. 5m
Remote control unit (RC6000CD)
CD player
1. Open the battery cover by lifting it in direction B while
pushing section A in the direction of the arrow.
2. Insert the provided batteries with correct polarity.
English
8
REMOTE CONTROL UNIT RC6000CD
When the power to the CD player is ON and a disc is loaded on the disc
tray, the remote control unit (RC6000CD) can be used to operate the
player’s various functions. However, the power to the CD player must be
switched ON/OFF using the POWER switch on the main unit.
nn
nn
n
EDIT button
,,
,,
,
STOP
button
..
..
.
PAUSE
button
⁄0⁄0
⁄0⁄0
⁄0
PLAY
button
⁄2⁄2
⁄2⁄2
⁄2
OPEN/CLOSE
button
⁄3⁄3
⁄3⁄3
⁄3
SCROLL/(RECALL) button
⁄4⁄4
⁄4⁄4
⁄4
CD-TEXT button
These buttons have the same functions as the buttons with the same
names on the main unit front panel. See the corresponding descriptions
on page 6.
mm
mm
m
, buttons
When the button is pressed during playback, play re-starts at
the beginning of the current or a previous track. When the
button
is pressed, play re-starts at the beginning of the next or a subsequent
track.
The selected track number is shown on the display.
These buttons can also be used to select a desired track from which to
start playback.
These buttons are also used in program mode to select tracks for
programming.
* The
and (Previous/Next Track) buttons on the remote
control do not start a search. Use the
and (Search
Reverse/Forward) buttons to conduct a search.
⁄6⁄6
⁄6⁄6
⁄6
TIME button
Switches the time shown on the display to the remaining time of the
current track or the remaining time of the entire disc.
With a CD-TEXT disc, this switch is also used to switch the displayed
information from the text display mode to the time display mode.
⁄7⁄7
⁄7⁄7
⁄7
REPEAT button
Press to select 1-track repeat, all-track repeat or program repeat
playback mode.
⁄8⁄8
⁄8⁄8
⁄8
A-B button
Used to set the starting and stopping points of a passage for repeated
playback.
⁄9⁄9
⁄9⁄9
⁄9
CANCEL button
Used to delete specified track numbers from a program.
Also used when creating programs by deleting any tracks which you do
not want to listen to (delete programming).
¤0 ¤0
¤0 ¤0
¤0
VOL ( + ),
¤1 ¤1
¤1 ¤1
¤1
VOL ( – ) buttons
Press to vary the ANALOG OUTPUT volume between 0 and -30 dB. The
level when the power is turned on is 0 dB (maximum volume).
¤2¤2
¤2¤2
¤2
PROG button
Press to activate program play, so that only the selected tracks from the
disc loaded on the disc tray will be played.
¤3¤3
¤3¤3
¤3
Numeric (0 to 9) buttons
When used during playback, these buttons allow you to specify the
number of another track you want to play.
When used during stop mode, these buttons allow you to specify the
number of a track from which to start playback.
These buttons are also used to select tracks for programming.
¤4¤4
¤4¤4
¤4
INDEX buttons
: Press during playback to advance to the next index.
: Press during playback to return to the next index.
*
These buttons are valid when playing a disc in which index have been
recorded.
¤5¤5
¤5¤5
¤5
, (Search Reverse/Forward) buttons
: When pressed during playback, this button fast-reverses the
play position.
: When pressed during playback, this button fast-forwards the
play position.
¤6¤6
¤6¤6
¤6
RANDOM button
When this button is pressed, the player enters random play mode (tracks
on the disc are selected and played in a random order). When pressed
again, random play is cancelled.
¤7¤7
¤7¤7
¤7
AMS (Automatic Music Scan)/HIGHLIGHT
When this button is pressed, the player automatically plays the first 10second part of each track in the disc.
If the loaded disc is a CD-TEXT disc containing the highlight information,
the first press of the button initiates the Highlight Scan operation and the
second press initiates the normal AMS operation as described above.
TIME
CD TEXT1SCROLL2HIGHLIGHT
EDIT REPEAT
A – B
RANDOM
RECALL AMS
PROG. CANCEL
3
4 5
8
0
7
6
9
VOLUME
REMOTE CONTROL UNIT
RC6000CD
⁄6
⁄4
¤2
¤1
¤5
n
⁄7
⁄3
⁄0
¤4
⁄2
¤7
¤3
⁄9
¤0
m
.
¤6
⁄8
,
English
9
Normal playback operation
CD player playback
q Press the
POWER
switch to turn on the power.
w Press the
OPEN/CLOSE
button.
When the disc tray opens, place a disc on the tray with the label side up.
e Gently press the front of the disc tray or press the
OPEN/CLOSE
button to close the tray.
r Press the
PLAY
button.
When the button is pressed, the
PLAY
indicator lights up.
While the disc is playing, the display shows the track number and
elapsed playing time of the track currently playing, along with the
numbers of the tracks still to be played or playing.
To stop playback:
Press the
STOP
button.
To remove the disc:
Open the disc tray by pressing the
OPEN/CLOSE
button, remove the
disc, then close the tray by lightly pressing its front edge. Always keep
the disc tray closed even when the CD player is not being used.
To pause playback:
Press the
PAUSE
button.
The PAUSE indicator lights up and playback pauses at the position
where the button was pressed. To resume playback from the pause
position, press the
PAUSE
button again.
To switch the time display:
Press the
TIME
button.
Each time the
TIME
button is pressed, the time display changes in the
following order: Elapsed playing time of the currently playing track fi
Remaining playing time of the current track fi Total remaining time in the
disc fi Elapsed playing time of the current track.
Display indications
PLAY
PHONES
OPEN/CLOSE
SCROLLPEAK SEARCH
POWER
ON/OFF
PAUSESTOP
EDIT
CD TEXT
qew
r
CD PLAYER
Remaining track numbers
TTL TRK INDX TIME
6 7 8 910 1112 1314 1516 1718 1920
Total number of tracks
Nunber of current track
Minutes
Seconds
English
10
SEARCHING/SKIPPING
Direct search (specifying a desired track number)
Specify the track number using numeric buttons 0 to 9.
For track number 3, press
3
.
For track number 12, press
1
, then, within 1.5 seconds, press 2.
If the first of two digits pressed is not one of the digits on the CD, it is
interpreted as 1 digit and the search will start after about 0.5 second.
If you make a mistake when pressing the numeric buttons:
Press the right buttons to enter the correct track number.
• If you specify a track number which does not exist on the disc, “No
Track” will appear on the display. Enter the correct number.
Track Skip
If the loaded disc is a CD-TEXT disc and the display is presently in the
text display mode, press the
TIME
button to switch it to the time display
mode.
Next (skipping to a desired track located after the
currently playing track)
Press the button the necessary number of times to skip to the
desired track.
Previous (skipping to a desired track located
after the currently playing track)
To skip to the previous track to the current track, press the button
twice. To skip to a track located before the previous track, press the
button for the necessary number of times to skip to the desired
track.
• Pressing the
button twice in the middle of the first track in a
disc skips to the last track, and pressing the
button in the
middle of the last track skips to the first track.
Index Skip ( )
This is a convenient function which allows to search the desired index
during playback of a track with indexes recorded in it (see the description of the INDEX buttons on page 8).
• When an index number that does not exist in the disc selected, the
display shows “No Index” and playback restarts from the begining of
the original index.
AMS (Listening to the first part of each track)
1. Press the
HIGHLIGHT/AMS
button during stop or playback.
The first part (first 10 seconds) of each track in the disc will be played in
the order in which the tracks are recorded.
2. When you find a track you want to listen to, press the
HIGHLIGHT/AMS
button again. (The PLAY indicator stops blinking and starts to light
steadily.)
• If the
or button is pressed during AMS operation, the
CD player increases or decreases the played track number for the
same number of times as the number of times the button was pressed,
but the AMS operation is not canceled.
Highlight Scan
When the loaded disc is a CD-TEXT disc containing the recording of
highlight information, pressing the
HIGHLIGHT/AMS
button initiates
the Highlight Scan operation in precedence over the AMS operation.
Pressing the
HIGHLIGHT/AMS
button during Highlight Scan initiates
the AMS operation.
REPEAT PLAY
1-track repeat
(repeated playback of one track only)
While the track you want to repeat is playing, press the
REPEAT
button
twice.
The “RPT” and “1” indicators light up and the current track will be played
repeatedly.
To cancel 1-track repeat play:
Press the
REPEAT
button once.
All-track repeat
(repeated playback of all tracks on the disc)
During playback, press the
REPEAT
button once.
The “RPT” indicator lights up and all the tracks on the disc are played
repeatedly.
Even if the
REPEAT
button is pressed in stop mode, playback will start
and repeat playback will be carried out.
To resume normal playback:
Press the
REPEAT
button twice. The “RPT” indicator goes out, repeat
mode is cancelled and normal playback resumes.
A-B repeat
(repeated playback of a specified passage)
1. During playback, press the remote control unit’s
A – B
button at the
starting point of the passage you want to repeat.“A-” (starting point)
indicator lights up.
2. Press the
A – B
button again at the end of the passage you want to
repeat. “B” (stopping point) indicator lights up.
The designated passage A-B will be played repeatedly.
To cancel A-B repeat play:
Press the
A – B
button, The “A” and “B” indicator goes out, A-B repeat
is cancelled and normal playback resumes.
12
TTL TRK
34 56 78 910 1112 1314 15
Blinks.
TEXT 1 2 3 4 5 6 7 8 9 10 1112 1314 15
English
11
PROGRAM PLAY
Programming (To play the desired tracks in a
certain order)
Programming when the display is in the time
display mode
If the loaded disc is a CD-TEXT disc, press the
TIME
button to switch
it to the time display mode.
(Example: To program track No. 15 first, then track No. 7 in a 15-track disc)
1. Press the
PROG.
button in stop mode. The PROG indicator flashes.
2. Specify the first track to be programmed using the numeric buttons or
the
or button.
(Display example: The first programmed track is track number 15 with
a playing time of 4 minutes 30 seconds)
3.Then program another track by repeating the procedure in step 2
above. Up to 30 tracks can be programmed in this way.
(Display example: The second programmed track is track No. 7 and
the total playing time of track Nos. 15 and 7 is 7 minutes 50 seconds.)
4. After having programmed all the desired tracks, press the
PROG.
button or
STOP
button.
The PROG indicator status changes from flashing to continuously lit,
indicating that the program is completed.
5. Press the
PLAY
button, The programmed tracks will be played in the
programmed order.
RANDOM PLAY
In this mode, the CD player automatically selects and plays tracks in
random order. All tracks are played once.
Press the
RANDOM
button.
Random playback begins in about 4 seconds.
• During random playback, tracks are separated by an interval of about
4 seconds.
• The
RANDOM
button can be pressed either during playback or in
stop mode.
If the
RANDOM
button is pressed while the disc tray is open with a disc
on the tray, the disc tray automatically closes and random playback
begins.
• To stop random playback and resume normal playback:
Press the
RANDOM
button again.
• If the
button is pressed during random playback:
Each time one of these buttons is pressed, the CD player selects a
track at random and starts playing that track.
• If the
or button is pressed during random playback:
Searching is carried out within the current track. The search operation
will not cross over into the previous or next track.
• To repeatedly play tracks at random:
Press the
REPEAT
button once. All tracks are repeatedly played in
random order, with the order being changed each time the disc is
played.
NOTE
• A-B repeat playback is not available during random playback.
• When the
RANDOM
button is pressed after the programming
operation (page 11) or delete programming operation (page 12),
random playback of the tracks selected with the programming or
delete programming operation starts.
34 56 78 910
12
TTL TIME
34 56 78 910 1112 1314 15
TTL
PROG
TTL TTL TIME
Flashes.
PROG
TTL TRK TTL TIME
15
Flashes.
Only the numbers of programmed
tracks light up.
PROG
TTL TRK TTL TIME
715
Total playing time of
programmed tracks
Last programmed track
Total programmed tracks
Light up continuously
PROG
TTL TTL TIME
715
English
12
Programming when the display is in the text
display mode
If the loaded disc is a CD-TEXT disc, tracks can also be programmed by
referring to the track titles.
If the display is not in the text display mode, press the
CD-TEXT
button
to put it to the text display mode.
(Example: To program track Nos. 15 and 7)
1. Press the
PROG.
button in stop mode. The PROG indicator flashes.
2. Specify the first track to be programmed using the numeric buttons or
the
or button.
The track title of the selected track scrolls.
In about 1 second after the
completion of scrolling, the track is automatically programmed. If you
do not want to program the track, select another track using the
numeric buttons or the
or button before the automatic
programming takes place.
(Display example: The first programmed track is track No. 15 with a
track title of "Phoenix".)
3.Then program another track by repeating the procedure in step 2
above.
(Display example: The second programmed track is track No. 7 with
a track title of "Moonlig..".)
4. After having programmed all the desired tracks, press the
PROG.
button or
STOP
button.
5. Press the
PLAY
button, The programmed tracks will be played in the
programmed order.
Delete programming (Listening only to the desired tracks by omitting unwanted tracks)
• Ordinary music CD: Delete programming is possible only when the
display is in the time display mode.
• CD-TEXT disc: Delete programming is possible whether the display is
in the time display mode or text display mode.
Delete programming when the display is in the
time display mode
If the loaded disc is a CD-TEXT disc, press the
TIME
button to switch
it to the time display mode.
(Example: To program the tracks on a 15-track disc with the exception
of track numbers 11, 7 and 3)
1. Press the
PROG.
button in stop mode and, when the PROG indicator
starts to flash, press the
CANCEL
button. The total number of tracks
and total playing time of the disc will be displayed.
(Display example: The total playing time is 65 minutes 32 seconds)
2. Select the unwanted tracks using the numeric buttons or the
or button. Up to 30 tracks can be selected and omitted in this
way.
(Display example: Track No. 11 is selected first and the total playing
time of the remaining tracks is 60 minutes 12 seconds.)
3. After having selected and deleted all of the unwanted tracks, press the
PROG.
button or
STOP
button.
The PROG indicator status changes from flashing to continuously lit,
indicating that the program is completed.
(Display example: The total playing time of the 12 tracks, omitting
track numbers 11, 7 and 3, is 51 minutes 22 seconds)
4. Press the
PLAY
button, The tracks except for the deleted tracks will
be played in the order of the track numbers.
TEXT 1 2 3 4 5 6 7 8 9 10 1112 1314 15
Alubm Title
In Stop mode
TEXT
PROG
TEXT
TTL
Flashes
Alubm Title
PROG
TEXT
TTL TRK
15
Track 15 title
Only the numbers of programmed
tracks light up.
PROG
TEXT
TTL TRK
715
Track title of track No. 7
Last programmed track
Total programmed track
PROG
TEXT 7 15
Lights up continuously
Alubm Title
TEXT 1 2
TTL TTL TIME
34 56 78 910 1112 1314 15
TEXT 1 2 3 4 5 6 7 8 9 10 1112 1314 15
PROG
TEXT 1 2
TTL TTL TIME
34 56 78 910 1112 1314 15
Flashes.
PROG
TEXT 1 2
TTL TRK TTL TIME
34 56 78 910 121314 15
The number of the deleted track goes out.
PROG
TEXT 1 2
TTL TTL TIME
4 56 8 910 12131415
Light up continuously
English
13
Delete programming when the display is in the
text display mode
If the loaded disc is a CD-TEXT disc, tracks can also be omitted by
referring to the track titles.
If the display is not in the text display mode, press the
CD-TEXT
button
to put it to the text display mode.
(Example: To omit track Nos. 11, 7 and 3)
1. Press the
PROG.
button in stop mode and, when the PROG indicator
starts to flash, press the
CANCEL
button. The total number of tracks
and alubm title of the disc will be displayed.
2. Select the unwanted tracks using the numeric buttons or the
or button.
The track title of the selected track scrolls. In about 1 second after the
completion of scrolling, the track is automatically omitted. If you do not
want to omit the track, select another track using the numeric buttons
or the
or button before completion of the scrolling. Up
to 30 tracks can be omitted in this way.
(Display example: The first selected track to be omitted is track No. 11
with a track title of "Graduat...".)
• By selecting a previously selected and omitted track again during
delete programming, the delete programming operation can be
suspended temporarily.
3. After having selected and deleted all of the unwanted tracks, press the
PROG.
button or
STOP
button.
The PROG indicator status changes from flashing to continuously lit,
indicating that the program is completed.
(Display example: The total 12 tracks, omitting track numbers 11, 7
and 3 and album title of disc.)
4. Press the
PLAY
button, The tracks except for the deleted tracks will
be played in the order of the track numbers.
NOTES
* Take note of the following points when programming tracks by
programming or delete programming.
* When selecting track numbers 1 to 9 using numeric buttons from
a disc containing 10 or more tracks (when selecting track number
3 after track number 2, for example), press 3 more than 1.5
seconds after pressing 2.
* When using numeric buttons to select track number 10 or higher on
a disc containing 10 or more tracks (for example when selecting
track number 13), press 3 within 1.5 seconds of pressing 1.
* When using numeric buttons to select track numbers on a disc
containing no more than 9 tracks (when selecting track number 5
after track number 4, for example), press 5 more than about 0.5
second after pressing 4.
* When programming track numbers using the
and
buttons, press buttons with intervals of less than 1 second.
To check the programmed contents:
Press the
SCROLL/(RECALL)
button during programming or program
playback.
If it is pressed during “programming”, the programmed track numbers
will be displayed sequentially in the order they have been programmed.
If it is pressed during “delete programming”, the deleted track numbers
will be displayed.
To erase some of the programmed tracks:
1.Press the
SCROLL/(RECALL)
button to display the programmed
track numbers sequentially in the order in which they have been
programmed.
2. When the track number to be erased from the program is displayed,
press the
CANCEL
button immediately.
The track number indicator of the track erased from the program goes
out.
To re-incorporate in the program a track which has been deleted in
“delete programming”:
1. Press the
SCROLL/(RECALL)
button during delete programming to
display the deleted track numbers sequentially in the order in which
they were deleted.
2.When the track number to be added to the program is displayed,
press the
CANCEL
button immediately.
The track number indicator of the track added to the program lights
up.
To erase the entire program:
During program playback, press the
STOP
button twice. In stop
mode, press the
STOP
button once.
• The program is also erased by pressing the
OPEN/CLOSE
button to
open the disc tray.
To add tracks to the program:
In stop mode with the program stored in the memory (that is, with the
PROG indicator lit up), press the
PROG.
button. The PROG indicator
starts flashing and more tracks can be added to the program.
Q&A
• How many tracks is it possible to program?
Up to 30 tracks can be included in the program. With delete
programming, up to 30 tracks can be omitted from the program.
• Is it possible to change from programming to delete programming
or vice versa?
No.
• How do you play programmed tracks repeatedly?
Press the
REPEAT
button once. The REPEAT indicator lights up
and the program playback will be repeated.
• How do you play programmed tracks in a random order?
Press the
RANDOM
button during program playback or in stop
mode.
• The display cannot be switched between the time display and text
display modes during programming or delete programming.
Be always sure to select either display mode before starting the
programming or delete programming operation.
TEXT 1 2 3 4 5 6 7 8 9 10 1112 1314 15
Alubm Title
In Stop mode
TEXT 1 2 3 4 5 6 7 8 9 10 1112 1314 15
PROG
TEXT 1 2
TTL
34 56 78 910 1112 1314 15
Alubm title
Flashes
PROG
TEXT 1 2
TTL
34 56 78 910 121314 15
Track title of track No. 11
Only the number indicators of
the omitted tracks go out.
PROG
TEXT 1 2 4 5 6 8 910 12 13 14 15
Lights up continuously
Alubm title
English
14
EDITING
When recording from a compact disc to a tape, use this function to match
the tape length to the playing time of the tracks to be recorded and to
create 4-second intervals between the tracks.
Peak search
If the cassette deck recording level is adjusted in relation to the peak
level on the disc, it is possible to avoid distortion and noise in recording.
This facility allows the peak over the entire disc or in the programmed to
be detected tracks before proceeding to editing.
Simple edit
This operation fits tracks into a specified tape length while keeping the
tracks in their original order.
1. Press the
EDIT
button in stop mode to light up the EDIT indicator.
(Example: When a disc with 28 tracks is loaded)
This example shows that, when the tape recording time is 90 minutes,
track 15 is the last track on tape side A and track 28 the last track on
tape side B. In other words, by using a 90-minute tape, all of the 28 disc
tracks can be accommodated by assigning tracks 1 to 15 on tape side
A and tracks 16 to 28 on tape side B.
2. To change the tape recording time, specify the new tape recording
time using the numeric buttons (0 to 9) or the
or
button.
• When numeric buttons are used to specify a C-46 tape, for example,
press
4
then 6.
This display example shows that, with a 46-minute tape, tracks 1 to 8
will be recorded onto tape side A and tracks 9 to 16 will be recorded
onto tape side B.
The blinking arrow on the right end of the character display shows that
tracks 17 and after cannot be recorded on the tape.
• Use of
and buttons
Each press of the
button allows you to change the recording
time in the order 90 fi 46 fi 54 fi 60 fi 74 fi 90.
Each press of the
button allows you to change the recording
time in the order 90 fi 74 fi 60 fi 54 fi 46 fi 90.
Each press of the
button allows you to increase the recording
time by 1 minute.
Each press of the
button allows to decrease the recording
time by 1 minute.
3. Press the
EDIT
button again and set the editing contents. If you are
omitting the next peak search, proceed to 6.
4. Press the
PEAK SEARCH
button on the main unit. "PEAK" will light up
and the peak search operation will begin from the first passage on the
disc. (Even if an ordinary CD is stopped, peak search can be
performed.
5.When peak search of the last passage is completed, play will be
repeated for approximately 6 seconds with the volume at a comparatively high level. Adjust the record level of the cassette deck. (Please
see the instruction manual for the cassette deck.) Press the
STOP
button so stop the peak search operation.
6. Press the
PAUSE
button to start edit play for tape side A.
7. After edit play for tape side A has been completed, the CD player
automatically enters pause mode to standby for the edit play of tape
side B.
8. To start edit play for side B, press the
PAUSE
button.
EDIT
TEXT 1 2 3 4 5 6 7 8 9 10 1112 1314 1516 1718 1920
EDIT
5 6 1314
The tape recording time display (90) appears.
Last track on tape side A
Last track on tape side B
Lights up.Blinks.
EDIT
TEXT 1 2 3 4 5 6 7 8 9 10 1112 1314 1516 1718 1920
Flashes.
EDIT A –
TEXT 1 2
TTL TTL TIME
34 56 78 910 1112 1314 15
Light up. Light up.
Total number of tracks on side A
Number indicators of tracks assigned to side A light up.
Total playing time of side A
EDIT
TEXT 1 2
TTL TRK INDX PEAK TIME
34 56 78 910 1112 1314 15
Lights up.
A –
EDIT
TEXT 1 2
TTL TTL TIME
34 56 78 910 1112 1314 15
A –
EDIT B
TEXT
TTL TTL TIME
16 1718 1920
Total number of tracks on side B Total playing time of side B
Number indicators of tracks
assigned to side B light up.
EDIT A – B
TEXT 1 2
TTL TRK INDX PEAK TIME
34 56 78 910 1112 1314 15
Lights up.
English
15
Program edit
This procedure allows you to record tracks in any desired order while
fitting the tracks into a specified tape length.
1. Program tracks according to the programming procedure in section
“PROGRAM PLAY” (page 11).
2. The rest of the program edit procedure is the same as step 1 to 8 in
the simple edit procedure.
Delete program edit
When recording from a disc to a tape, this procedure allows you to omit
the tracks you do not want to record, while fitting the tracks into a
specified tape length.
1. Program tracks according to the “delete programming” procedure in
the “PROGRAM PLAY” section (page 12).
2. The rest of the delete program edit procedure is the same as step 1
to 8 in the simple edit procedure.
NOTES
• As a CD may contain several peaks, a different peak may be found
every time the auto peak level search operation is performed.
• During simple edit play, program edit play and delete program edit
play operations other than the STOP, OPEN/CLOSE, VOLUME,
RECALL and TIME control operations are defeated. This is intended to prevent mistakes in recording due to erroneous operation.
• The display is always in the time display mode during edit play. It is
not possible to switch to the text display mode.
Synchro Recording
This function starts the recording of the cassette deck automatically in
synchronism with the start of edit play of the CD player.
– Synchro recording can be started only when a Marantz autoreverse
cassette deck (ex. SD4050, SD555 etc.) with synchro recording
compatibility is connected to the CD player.
– Synchro recording is performed through the remote line connection
(rear panel jacks).
1.Set up the cassette deck for synchro recording. For the detailed
operations, please refer to the User Guide of the cassette deck.
2. When the pause button of the CD player is pressed to start the edit play
for tape side A, the cassette deck also starts automatically.
NOTE
When a tape with shorter length than the set tape recording time, the
CD player stops playback of tracks assigned for tape side A at the
moment recording of side A has completed. When recording of tape
side B starts, the CD player also starts playback of the tracks assigned
for side B.
CD-TEXT information display
The text information on CD-TEXT discs is displayed in the order shown
below each time the CD-TEXT button on the remote control unit is
pressed.
However that the included information differs from disc to disc,
so not all this information will necessarily be displayed. With this set,
items for which no text information is recorded on the disc are automatically skipped.
The displayed text can be scrolled by pressing the
SCROLL/(RECALL)
button.
• During playback
The displayed information switches in the order below each time the
CD-TEXT
button is pressed. During playback, most of the displayed
information is for the currently playing track.
• In the stop mode
The displayed information switches in the order below each time the
CD-TEXT
button is pressed.
Title of currently playing track
fl
Album Title (album title)
fl
xx Title (title of track number xx)
fl
xx Artist (artist of track number xx)
fl
xx Songwriter (songwriter of track number xx)
fl
xx Composer (composer of track number xx)
fl
xx Arranger (arranger of track number xx)
fl
xx Message (message for track number xx)
fl
Disc ID (album identification number)
fl
Genre (album’s music category)
fl
xx Info. End (end of information for track number xx)
Album Title
fl
Album Title (album title)
fl
-- Title (title of -- track)
fl
Artist (album’s artist)
fl
-- Artist (artist of -- track)
fl
Songwriter (album’s songwriter)
fl
-- Songwriter (songwriter of -- track)
fl
Composer (album’s composer)
fl
-- Composer (composer of -- track)
fl
Arranger (album’s arranger)
fl
-- Arranger (arranger of -- track)
fl
Message (album’s message)
fl
-- Message (message for -- track)
fl
Disc ID (album identification number)
fl
Genre (album’s music category)
fl
All Info. End (end of all text information)
English
16
TROUBLE SHOOTING
If you think a malfunction has occurred, first check the points listed
below, The problem is likely to have been caused by a simple operational
error or a connection problem. If the problem cannot be corrected even
after carrying out the following checks, consult your dealer or nearest
Marantz sales office or service counter.
• The disc fails to rotate.
1. Is the mains lead plugged in properly?
2. Is the POWER switch ON?
3. Is the disc placed in the correct position on the disc tray?
4. Is the disc placed properly with the label side facing up?
5. Is the disc dirty?
6. Is the disc scratched?
7. Is the disc warped?
• The disc is rotating but no sound is heard.
1. Are the amplifier and speakers connected properly?
2. Is the amplifier switch ON?
3. Is the amplifier’s volume control set at the minimum level?
4. Is the amplifier’s selector switch set to the correct input (“CD” or
“AUX”, whichever corresponds to the input jacks the CD player is
connected to)?
• The disc stops in mid-operation.
1. Is the disc dirty?
2. Is the disc scratched?
3. Is the disc warped?
• The sound drops out or noise is heard.
1. Is the disc dirty?
2. Is the disc scratched?
3. Is the disc warped?
• Remote control operation is not possible.
1. Is the remote control unit’s transmitter pointed correctly at the remote
sensor on the front of the CD player?
Or is there an obstruction between the transmitter and the remote
sensor?
2. Are the batteries in the remote control unit exhausted?
3.Is there another strong light (from a window, etc.) striking the CD
player’s remote sensor?
4. Is an RCA-type pin-plug lead connected to the “REMOTE CONTROL
IN” jack on the CD player’s rear panel?
• A CD-R/CD-RW disc cannot be played.
1. Is the disc placed upside down?
2. Is the disc contains properly written TOC?
OPERATING PRECAUTIONS
• In the winter you may notice that condensation forms on the window
of a well-heated room.
Condensation may also occur inside the CD player in the following
situations:
– When the listening room is first heated.
– When the humidity in the room is high.
– When the unit is moved from a cold environment to a warm room.
• If condensation occurs, the number of tracks cannot be read and the
CD player may not function properly. If this happens, leave the power
ON and wait for about 30 minutes before operating the unit.
• The CD player may interfere with the reception of your tuner or TV set.
If this occurs, place the CD player farther away from the tuner or TV.
• The CD player features very little noise compared to analog records,
and the noise before actual playback begins is almost inaudible.
Therefore, be careful not to set the volume control of the amplifier too
high, otherwise other audio components such as the speakers may be
damaged when actual playback starts.
CLEANING OF EXTERIOR SURFACES
With proper care and cleaning, the exterior finish of your equipment will
last indefinitely. Never use scouring pads, steel wool, scouring powders
or harsh chemical agents (e.g. lye solution), alcohol, thinners,benzine,
insecticide or other volatile substances, as these will mar the finish of the
cabinet. Likewise, never use cloths containing chemical substances. If
the equipment becomes dirty, wipe the external surfaces with a soft, lintfree cloth.
If the cabinet becomes heavily soiled:
– dilute some washing-up liquid in water, in a ratio of one part detergent
to six parts water;
– dip a soft, lint-free cloth in the solution and wring the cloth out until it
is damp;
– wipe the equipment with the damp cloth;
– dry the equipment by wiping it with a dry cloth.
REPAIRS
Only the most competent and qualified service technicians should be
allowed to service the equipment. The Marantz company and its factorytrained warranty station personnel have the knowledge and special
facilities needed for the repair and calibration of this precision equipment. After the warranty period has expired, repairs will be performed for
a charge if the equipment can be restored to normal operation.
In the event of difficulty, consult your dealer or write directly to the nearest
location to you that is listed on the Marantz Authorized Service Station
list. Please quote the model and serial number of the equipment and give
a full description of what you think is abnormal about the equipment’s
behaviour.
MODEL CD6000/CD6000OSE TECHNICAL SPECIFICATIONS
Audio Characteristics
Channels ........................................................................................................................................................................ 2 channels
Sampling frequency...........................................................................................................................................................44.1 kHz
Quantization .................................................................................................................................................... 16-bit linear/channel
Error correction ......................................................................................................... Cross-interleave read solomon code (CIRC)
D/A conversion..................................................................................................................................................1-bit linear/channel
Wow & flutter ...................................................................................................................................................... Precision of quartz
Optical Readout System
Laser .......................................................................................................................................................... GaAIAs semiconductor
Wavelength ..........................................................................................................................................................................780 nm
Frequency Characteristics
Frequency range............................................................................................................................................................ 5Hz-20kHz
Dynamic range .................................................................................................................................................................... > 98 dB
S/N ratio (WTD) .................................................................................................................................................................. > 103 dB
Channel separation (1 kHz) ................................................................................................................................................ >100 dB
THD (1 kHz) ....................................................................................................................................................................... 0.0025 %
Analog output
Output level (cinch JACKS) ......................................................................................................................................... 2.0 V RMS
Output impededance ................................................................................................................................................... 250 ohms
Digital output
output level (cinch JACK)............................................................................................................................... 0.5 Vp-p/75 ohms
output level (optical) ...................................................................................................................................................... -19 dBm
Power Supply
N, T version ............................................................................................................................................................ 230V AC 50 Hz
Power Consumption .................................................................................................................................................................13 W
Cabinet, etc.
Dimensions
Width............................................................................................................................................................................... 440 mm
Height ...............................................................................................................................................................................86 mm
Depth ..............................................................................................................................................................................312 mm
Net weight ......................................................................................................................................................CD6000 4.1 kg
CD6000OSE 5.6 kg
Operating temperatures................................................................................................................................................. +5 ˚C ~ +35 ˚C
Operating humidity................................................................................................................................. 5 % ~ 90 % (without dew)
Accessories
Remote control unit (RC6000CD).................................................................................................................................................. 1
AAA (R03) Batteries ....................................................................................................................................................................... 2
Stereo audio cable with cinch pins .........................................................................................................................................1 pair
Remote cable with cinch pins ........................................................................................................................................................1
Specifications subject to change without prior notice.
Model CD6000 / CD6000OSE
PLAY
PHONES
OPEN/CLOSE
SCROLLPEAK SEARCH
POWER
ON/OFF
PAUSESTOP
EDIT
CD TEXT
L
R
IN
OUT
ANALOGUE
OUTPUT
DIGITAL
OUTPUT
REMOTE
CONTROL
OPTICAL COAXIAL
EXTERNAL INTERNAL
z x
⁄1 ⁄3 ⁄4 b⁄2
A B C E FD
,mn
c v
. ⁄0
FRONT VIEW
REAR VIEW
CD PLAYER
Loading...