Marantz CC3000, CC4000 User Manual

R

Model CC3000/CC4000/CC4000 OSE User Guide

5 Disc CD Changer

The lightning flash with arrowhead symbol, within an equilateral triangle,
is intended to alert the user to the presence of uninsulated “dangerous
voltage” within the product’s enclosure that may be of sufficient magni­tude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operating and maintenance (ser­vicing) instructions in the literature accompanying the appliance.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

CAUTION:

TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

ATTENTION:

POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPON­DANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.

LASER SAFETY

This unit employs a laser, Only a qualified service person should remove the cover or attempt to service this device, due to
possible eye injury.

CAUTION:

USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURE OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS
RADIATION EXPOSURE.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

English

Français

English . . . . . . . . . . . . . . . . . . . .4

Français . . . . . . . . . . . . . . . . . .19

NOTE

:

This equipment has been tested and found to
comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reason­able protection against harmful interference in
a residential installation. This equipment gen­erates, uses and can radiate radio frequency
energy and, if not installed and used in accor­dance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interfer­ence will not occur in a particular installation. If
this equipment does cause harmful interfer­ence to radio or television reception, which
can be determined by turning the equipment off
and on, the user is encouraged to try to correct
the interference by one or more of the following

measures:

– Reorient or relocate the receiving anten-

na.

– Increase the separation between the

equipment and receiver.

– Connect the equipment into an outlet on a

circuit different from that to which the
receiver is connected.

– Consult the dealer or an experienced

radio/TV technician for help.

NOTE

:

Changes or modifications may cause
this unit to fail to comply with Part 15 of the FCC
Rules and may void the user’s authority to
operate the equipment.

This Class B digital apparatus meets all
requirements of the Canadian Interference­Causing Equipment Regulations.

Cet appareil numérique de la Classe B
respecte toutes les exigences du Règlement
sur le matérier brouilleur du Canada.

4

English

This product was designed and manufactured to meet strict quality and safety stan­dards. There are, however, some installation and operation precautions which you
should be particularly aware of.

1. Read Instructions - All the safety and operating instructions should be read
before the appliance is operated.

2. Retain Instructions - The safety and operating instructions should be retained for
future reference.

3. Heed Warnings - All warnings on the appliance and in the operating instructions
should be adhered to.

4. Follow Instructions - All operating and use instructions should be followed.

5. Water and Moisture - The appliance should not be used near water - for example,

near a bathtub, washbowl, kitchen sink, laundry tub or swimming pool, or in a wet
basement.

6. Carts and Stands - The appliance should be used only with a cart or stand that is
recommended by the manufacturer.

6A. An appliance and cart combination should be moved with

care. Quick stops, excessive force, and uneven surfaces may
cause the appliance and cart combination to overturn.

7. Wall or Ceiling Mounting - The appliance should be mounted to a wall or ceiling
only as recommended by the manufacturer.

8. Ventilation - The appliance should be situated so that its location or position does
not interfere with its proper ventilation. For example, the appliance should not be
situated on a bed, sofa, rug, or similar surface that may block the ventilation open­ings; or, placed in a built-in installation, such as a bookcase or cabinet that may
impede the flow of air through the ventilation openings.

9. Heat - The appliance should be situated away from heat sources such as radiators,
heat registers, stoves, or other appliances (including amplifiers) that produce heat.

10. Power Sources - The appliance should be connected to a power supply only of
the type described in the operating instructions or as marked on the appliance.

11. Grounding or Polarization - Precautions should be taken so that the grounding
or polarization means of an appliance is not defeated.

Caution:

To prevent electric
shock, match the wide blade of this plug to the wide
slot and fully insert. Do not use this (polarized) plug
with an extension cord, receptacle or other outlet
unless the blades can be fully inserted to prevent
blade exposure.

12. Power Cord Protection - Power supply cords should be routed so that they are
not likely to be walked on or pinched by items placed upon or against them, paying
particular attention to cords and plugs, convenience receptacles, and the point
where they exit from the appliance.

13. Cleaning - The appliance should be cleaned only as recommended by the manufac­turer.

14. Power Lines - An outdoor antenna should be located away from power lines.

15. Outdoor Antenna Grounding - If an outside antenna is connected to the receiver,

be sure the antenna system is grounded so as to provide some protection against
voltage surges and built up static charges.
Section 810 of the National Electrical Code, ANSI/NFPA No. 70-1984, provides
information with respect to proper grounding of the mast and supporting structure,
grounding of the lead-in wire to an antenna discharge unit, size of grounding con­nectors, location of antenna-discharge unit, connection to grounding electrodes, and
requirements for the grounding electrode. See figure below.

16. Non-use Periods - The power cord of the appliance should be unplugged from the
outlet when left unused for a long period of time.

17. Object and Liquid Entry - Care should be taken so that objects do not fall and liq­uids are not spilled into the enclosure through openings.

18. Damage Requiring Service - The appliance should be serviced by qualified ser­vice personnel when:

A. The power supply cord or the plug has been damaged; or
B. Objects have fallen, or liquid has spilled into the appliance; or
C. The appliance has been exposed to rain; or
D. The appliance does not appear to operate normally or exhibits a marked change

in performance; or

E. The appliance has been dropped, or the enclosure damaged.

19. Servicing - The user should not attempt to service the appliance beyond that

described in the operating instructions. All other servicing should be referred to
qualified service personnel.

SAFETY INSTRUCTIONS – Read before operating equipment

5

English

SAFETY INSTRUCTIONS

Note to the Cable TV system installer

This reminder is provided to call the Cable TV system installer's attention to Article 820-40 of the NEC that provides guidelines for proper grounding
and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as
practical.

Example of Antenna Grounding as
per NEC - National Electrical Code

Ground Clamp

Antenna Lead-in Wire

Antenna Discharge Unit
(NEC Section 810-20)

Grounding Conductors
(NEC Section 810-21)
Ground Clamps

Electric Service Equipment

Power Service Grounding Electrode System
(NEC Art. 250, Part H)

6

English

Thank you for selecting the Marantz CC 3000 &
CC4000 & CC4000 OSE Compact Disc Changer.

A Compact Disc Changer of the state-of-the-art Marantz
the CC 3000, CC4000 & CC4000 OSE combines supreme
playback quality with a high degree of user-friendliness
by offering the following possibilities:
– able to play CD-RW disc;
– changing CDs during play;
– quick access to a particular CD by means of QUICK

PLAY;

– storing 40 tracks from different CDs in any desired

order in the changer memory;

– storing the required recording time and playing time

in the EDIT mode.

Power Supply Setting

• Check that the type plate on the rear of your changer
indicates the correct supply voltage.

• If your mains supply voltage is different, consult your
dealer or our Service Organisation.

Siting the Compact Disc Changer

Free standing

• Always position the changer horizontally on a flat,
firm surface.

• Allow a free space of at least 3 cm above the
changer so as not to interfere with the cooling of the
changer.

In an audio rack

• The changer can be sited in any desired position.

Stacked

• Site the changer preferably at the bottom or at the
top.

• Never position the changer directly on top of a high­power amplifier, as such an amplifier gives off a
substantial amount of heat.

Introduction . . . . . . . . . . . . . . . . . . . . . . .6

Installation . . . . . . . . . . . . . . . . . . . . .6 - 7

Functional Overview . . . . . . . . . . . . .7 - 9

Playback . . . . . . . . . . . . . . . . . . . . .11 - 15

Programming . . . . . . . . . . . . . . . . . . . . .15

Edit . . . . . . . . . . . . . . . . . . . . . . . . . .16 - 17

Additional Information . . . . . . . . .17 - 18

Troubleshooting . . . . . . . . . . . . . . . . . . .18

CONTENTS INTRODUCTION INSTALLATION

RECEIVER

CASSETTE DECK

CD CHANGER

Connections

1 Digital Out

This output supplies digital signal and can therefore
only be connected to an input which is suitable for
this signal. Use here a lead with one cinch plug on
either end.

Never connect this socket to a non-digital input
of an amplifier, such as AUX, CD, TAPE, PHONO
etc!

2 Analog Out

For the connecting cable to the amplifier.

• Insert a red plug into the ‘R’ socket and the
other plug into the ‘L’ socket.

• Insert the two other plugs into the corresponding
sockets of the CD or AUX input of your amplifier.
You can also use the TUNER or TAPE IN connection,
but never the PHONO input!

3 Remote Control

For connecting up the equipment when you are
incorporating the changer in a HiFi system with its
own remote control system.

Connecting Headphones (for CC4000 &
CC4000OSE only)

• Connect headphones with a 6.3 mm jack plug to the
PHONES socket.

• The sound level is adjusted with the LEVEL control.

Note:
– The volume control on the remote control must not be

at the minimum level.

PHONES/

LEVEL

7

English

INSTALLATION

COAXIAL

DIGITAL
OUTPUT

RL

ANALOG

OUT

IN OUT

REMOTE

CONTROL

21

3