Marantz 541110331126M, BD5004 User Manual

BD5004
ENGLISH FRANÇAIS ESPAÑOL
The serial number of this product may be found on the back of the unit. No others have the same serial number as yours. You should record the number and other vital information here and retain this book as a permanent record of your purchase to aid identification in case of theft.
Date of Purchase Dealer Purchase from Dealer Address Dealer Phone No. Model No. Serial No.
Safety Precautions
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to consti tute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.
APPARATUS SHALL NOT BE EXPOSED TO DRIPPING OR SPLASHING AND NO OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, SHALL BE PLACED ON THE APPARATUS.
The important note and rating are located on the rear or bottom of the cabinet.
Laser Safety
CAUTION:
VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN. DO NOT STARE INTO BEAM.
LOCATION: INSIDE, NEAR THE DECK MECHANISM.
CAUTION:
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. THIS PRODUCT SHOULD NOT BE ADJUSTED OR REPAIRED BY ANYONE EXCEPT PROPERLY QUALIFIED SERVICE PERSONNEL.
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacture’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
15. Batteries shall not be exposed to excessive heat such as sunshine, fire or the like.
FCC INFORMATION (For US customers)
1. PRODUCT
This product complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this product may not cause harmful interference, and (2) this product must accept any interference received, including interference that may cause undesired operation.
2. IMPORTANT NOTICE: DO NOT MODIFY THIS PRODUCT
This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modification not expressly approved by Marantz may void your authority, granted by the FCC, to use the product.
3. NOTE
This product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This product generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this product does cause harmful interference to radio or television reception, which can be determined by turning the product OFF and ON, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the product into an outlet on a circuit different from that to which the receiver is connected.
• Consult the local retailer authorized to distribute this type of product or an experienced radio/TV technician for help.
This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme
NMB-003 du Canada.
Disconnect the mains plug to shut off when find trouble or not in use. The mains plug shall remain readily operable.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LAFICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.
Do not place the unit on the furniture that is capable of being tilted by a child and an adult leaning, pulling, standing or climbing on it. A falling unit can cause serious injury or even death.
I
CLASS 1
LASER PRODUCT
Copyrights / Droits d’auteur / Derechos de Autor
• It is prohibited by law to reproduce, broadcast, rent or play discs in public without the consent of the copyright holder.
• La reproduction, la diffusion, la location, le prêt ou la lecture publique de ces disques sont interdits sans le consentement du détenteur des droits d’auteur.
• De acuerdo con las leyes está prohibido reproducir, emitir, alquilar o interpretar discos en público sin la autorización del propietario de los derechos de autor.
Note on use / Observations relatives a l’utilisation / Notas sobre el uso
• Keep the apparatus free from moisture, water, and
Avoid high temperatures. Allow for sucient heat dispersion when installed in a rack.
• Eviter des températures élevées Tenir compte d’une dispersion de chaleur susante lors de l’installation sur une étagère.
• Evite altas temperaturas Permite la suciente dispersión del calor cuando está instalado en la consola.
dust.
• Protéger l’appareil contre l’humidité, l’eau et lapoussière.
• Mantenga el equipo libre de humedad, agua y polvo.
• Do not let foreign objects into the apparatus.
• Ne pas laisser des objets étrangers dans l’appareil.
• No deje objetos extraños dentro del equipo.
ESPAÑOL FRANÇAIS ENGLISH
• Handle the power cord carefully. Hold the plug when unplugging the cord.
• Manipuler le cordon d’alimentation avec précaution. Tenir la prise lors du débranchement du cordon.
• Maneje el cordón de energía con cuidado. Sostenga el enchufe cuando desconecte el cordón de energía.
II
• Unplug the power cord when not using the apparatus for long periods of time.
• Débrancher le cordon d’alimentation lorsque l’appareil n’est pas utilisé pendant de longues périodes.
• Desconecte el cordón de energía cuando no utilice el equipo por mucho tiempo.
* (For apparatuses with ventilation holes)
• Do not obstruct the ventilation holes.
• Ne pas obstruer les trous d’aération.
• No obstruya los oricios de ventilación.
• Do not let insecticides, benzene, and thinner come in contact with the apparatus.
• Ne pas mettre en contact des insecticides, du benzène et un diluant avec l’appareil.
• No permita el contacto de insecticidas, gasolina y diluyentes con el equipo.
• Never disassemble or modify the apparatus in any way.
• Ne jamais démonter ou modier l’appareil d’une manière ou d’une autre.
• Nunca desarme o modique el equipo de ninguna manera.
ENGLISH
Introduction Connections Playback Function Setup Others
Contents
Introduction
Important ..................................................................................2
Power Supply ............................................................................2
Warning .....................................................................................2
Installation Location ................................................................2
Cautions on Installation ...........................................................2
Cautions on Handling ..............................................................2
Dew Warning ............................................................................2
Avoid the Hazards of Electrical Shock and Fire .....................2
Before Using .............................................................................2
About Copyright .......................................................................2
Features ....................................................................................3
Supplied Accessories ...............................................................3
About Discs ...............................................................................3
Disc Handling ........................................................................................... 3
Cleaning Discs ......................................................................................... 3
Playable Discs and Files ....................................................................... 4
Unplayable Discs .................................................................................... 5
Color Systems ..........................................................................................5
Region Codes ........................................................................................... 5
Structure of Disc/SD Memory Card Contents .............................. 5
Symbols Used in this User Guide ...................................................... 5
About the Remote Control ......................................................6
Loading the Batteries ............................................................................ 6
Using a Remote Control ....................................................................... 6
Changing the Signal Code of a Remote Control ......................... 6
Part Names and Functions ....................................................... 7
Front Panel ............................................................................................... 7
Rear Panel ................................................................................................. 7
Remote Control ....................................................................................... 8
Front Panel Display ................................................................................ 9
Adjusting the Brightness of the Display ........................................ 9
Examples of Displays during Operation .......................................10
Connections
Connecting to a TV ...............................................................................12
Connecting to a Display Device with HDMI Cable ...................12
Connecting to a Display Device and an Amplifier/
Receiver with HDMI Cable ..............................................................12
HDMI Output Mode and Actual Output Signals ........................13
Audio Setting .........................................................................................13
Digital Connection to an AV Amplifier with Built-in
Decoder .................................................................................................14
Connection to a Device with 2-channels of Analog
Audio Inputs ........................................................................................15
Network Connection with LAN ........................................................15
Connecting the AC cord .....................................................................16
Playback
Turning the Power On ........................................................... 17
Direct Playback ...................................................................... 17
Operations Using Disc Menu, Title Menu, and
Popup Menu ......................................................................... 18
Playing Back a VR mode DVD-RW/-R ................................... 18
Pause ....................................................................................... 18
Resume Playback ................................................................... 18
Fast Forward / Fast Reverse Playback ..................................19
Slow Forward Playback .........................................................19
Step by Step Playback ...........................................................19
Dialog Speed ..........................................................................19
Repeat Playback ..................................................................... 20
A-B Repeat ...............................................................................................20
Program Playback .................................................................. 20
PIP (Picture in Picture) (BONUSVIEW) Setting .....................20
Random Playback ..................................................................21
Zoom .......................................................................................21
Camera Angle ......................................................................... 22
Search ..................................................................................... 22
On-Screen Display .................................................................. 23
Selecting the Format of Audio and Video ............................24
Selecting Audio Streams/Channels ............................................... 24
Selecting Subtitle Language ............................................................ 25
Virtual Surround ................................................................................... 25
Pure Direct Mode ................................................................................. 25
Setting the BD Audio Mode .............................................................25
Adjusting the Picture .......................................................................... 26
Playing Back an Audio CD or a Disc with DivX®/MP3/
Windows Media™ Audio/JPEG File ......................................26
Kodak Picture CD ................................................................................. 28
Reading the SD Memory Card ...............................................28
Enjoying BD-Live Discs with Internet ...................................29
Function Setup
Using the Setup Menu ....................................................................... 30
Quick ........................................................................................30
Custom ....................................................................................30
Network Connection ..............................................................39
Connection Test ................................................................................... 39
Enable(Easy) ........................................................................................... 39
Enable(Custom) .................................................................................... 39
Disable ..................................................................................................... 41
Network Update .....................................................................41
Initialize ..................................................................................42
Others
Trademark Information .........................................................43
Explanation of Terms .............................................................43
Index ........................................................................................46
Troubleshooting .....................................................................47
Language Code .......................................................................48
Specifications ..........................................................................49
1
ENGLISH
ENGLISH
Introduction
Important
Use only discs marked with logos listed on page 4.
Power Supply
The main power supply is engaged when the main plug is plugged in a 120V, 60Hz AC outlet. To operate the unit, press
[POWER ON] or <POWER ON/STANDBY> to turn on the unit.
Warning
To avoid fire or electric shock, do not expose this unit to rain or moisture.
WARNING: LIVE PARTS INSIDE. DO NOT REMOVE ANY SCREWS.
Installation Location
For safety and optimum performance of this unit:
• Do not stand the unit up vertically. Install the unit in a horizontal and stable position. Do not place anything directly on top of the unit. Do not place the unit directly on top of the TV.
• Shield it from direct sunlight and keep it away from sources of intense heat. Avoid dusty or humid places. Avoid places with insufficient ventilation for proper heat dissipation. Do not block the ventilation holes on the sides of the unit. Avoid locations subject to strong vibration or strong magnetic fields.
• Be sure to remove a disc and unplug the AC cord from the outlet before carrying the unit.
Non-use periods - Turn off the unit when it is not in use. Unplug the unit from the household AC outlet if it is not to be used for a long time. Unplug the unit during lightning storms.
Please read this user guide carefully before using the unit, and keep it for future reference.
Cautions on Installation
Noise or disturbance of the picture may be generated if this unit or any other electronic equipment using microprocessors is used near a tuner or TV.
If this happens, take the following steps:
• Install this unit as far as possible from the tuner or TV.
• Set the antenna wires from the tuner or TV away from this unit’s AC cord and input/output connection cords.
• Noise or disturbance tends to occur particularly when using indoor antennas or 300/ohms feeder wires. We recommend using outdoor antennas and 75/ohms coaxial cables.
Note
• For heat dispersal, do not install this equipment in a
confined space such as a book case or similar unit.
10 cm or more
Wall
Cautions on Handling
Cautions on using mobile phones.
Using a mobile phone near this unit may result in noise. If so, move the mobile phone away from this unit when it is in use.
Before turning the power operation button on.
Check once again that all connections are correct and that there are no problems with the connection cables. Always set the power operation button to the standby position before connecting and disconnecting connection cables.
Sufficiently ventilate the place of installation.
If the unit is left in a room full of the smoke from cigarettes, etc., for long periods of time, the surface of the optical pickup could get dirty, in which case it will not be able to read the signals properly.
Introduction Connections Playback Function Setup Others
Dew Warning
Moisture condensation may occur inside the unit when it is moved from a cold place to a warm place, or after heating a cold room or under conditions of high humidity. Do not use the unit at least for 2 hours until its inside is dry.
Avoid the Hazards of Electrical Shock and Fire
• Do not handle the AC cord with wet hands.
• Do not pull on the AC cord when disconnecting it from AC wall outlet. Grasp it by the plug.
• If, by accident, water is spilled on this unit, unplug the AC cord immediately and take the unit to our authorized service center for servicing.
Before Using
Pay attention to the following before using this unit:
Moving the unit.
To prevent short-circuits or damaged wires in the connection cables, always unplug the power supply cord and disconnect the connection cables between all other audio components when moving the unit.
Store the user guide in a safe place.
After reading the user guide, store it in a safe place as it could come in handy in the future.
Whenever <POWER ON/STANDBY> is in the STANDBY state, the unit is still connected to AC line voltage.
Please be sure to unplug the cord when you leave home for, say, a vacation.
Note that the illustrations in these instructions may differ from the actual unit for explanation purposes.
About Copyright
Unauthorized copying, broadcasting, public performance and lending of discs are prohibited.
This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision.
Reverse engineering or disassembly is prohibited.
U. S. Patent No’s, 6,836,549; 6,381,747; 7,050,698; 6,516,132 and 5,583,936.
2
ENGLISH
ENGLISH
Introduction Introduction
Features
Introduction Connections Playback Function Setup Others
PIP (Picture in Picture) (BONUSVIEW) Setting
Some BD-Video have the PIP (picture-in-picture) function which enables you to display the secondary video in the primary video. You can call up the secondary video by pressing [MODE] whenever the scene contains the secondary video.
Pure Direct
The sound quality of analog audio output is improved by stop output of video signals, etc.
On-Screen Display
Information about the current operation can be displayed on a screen, allowing you to confirm the currently active functions (such as program playback) using the remote control.
Picture Control
Picture control adjusts the picture quality of the specific display.
DRC (Dynamic Range Control)
Use this procedure to set the dynamic range of the output signals when playing back BD/DVD/AVCHD recorded in Dolby Digital/Dolby Digital Plus/Dolby TrueHD.
BD-Live
BD-Live (BD-ROM version 2 Profile 2.0) that allows interactive functions to be used when this unit is connected to the Internet in addition to the BONUSVIEW function. The various functions differ depending on the disc.
x.v.Color
This unit supports playback of video contents on discs recorded with “x.v.Color” technology. To watch this video content with the “x.v.Color” space, a TV or other display device supporting both video image reproduction using “x.v.Color” standard and capability of manual switching of its color space setting is required. Please refer to the user guide of your display device for further information.
Supplied Accessories
Please check to make sure the following items are included with the main unit in the carton.
remote control (RC004BD) “AA” (R6) batteries x2
About Discs
Disc Handling
• Handle the discs so that fingerprints and dust do not adhere to the surfaces of the discs.
• Always store the disc in its protective case when it is not used.
• Note that discs with special shapes cannot be played on this product. Do not attempt to play back such discs, as they may damage the unit.
Cleaning Discs
• When a disc becomes dirty, clean it with a cleaning cloth. Wipe the disc from the center to out. Do not wipe in a circular motion.
• Do not use solvents such as benzine, thinner, commercially available cleaners, detergent, abrasive cleaning agents or antistatic spray intended for analog records.
Playing Back the Contents in SD Memory Card
• You can playback AVCHD, MP3, Windows Media™ Audio, or JPEG stored in an SD Memory Card.
• You can store picture-in-picture commentary, subtitles or other extras for BD-ROM ver. 2 (Profile 2.0/ Profile 1.1) files in an SD Memory Card and playback with the BD-ROM.
AC cord (5.2ft/1.6m) user guide
Playing Back AVCHD Files
This unit supports playback of AVCHD format files (new format for high definition video camcorders) recorded on disc/SD card. Your high definition personal archive is playable in HD quality.
Playing Back DivX
You can enjoy DivX® files which are recorded on BD-RE/-R, DVD-RW/-R or CD-RW/-R.
• Official DivX
• Plays all versions of DivX
®
File
®
Certified product
®
video (including DivX® 6/DivX®HD)
warranty card RCA audio cable (3.2ft/1.0m)
with standard playback of DivX® media files.
Playing Back an MP3 File
You can enjoy MP3 files which are recorded on BD-RE/-R, DVD-RW/-R, CD-RW/-R or SD Memory Card.
Playing Back Windows Media™ Audio File
You can enjoy Windows Media™ Audio files which are recorded
RCA video cable (3.2ft/1.0m)
on BD-RE/-R, DVD-RW/-R, CD-RW/-R or SD Memory Card.
Displaying a JPEG picture
Kodak Picture CD can be played back. Still images stored in JPEG format on BD-RE/-R, DVD-RW/-R, CD-RW/-R or SD Memory Card can also be played back.
BD-J Application
• With some BD that supports Java applications (BD-J), you can enjoy interactive function (e.g. game).
3
ENGLISH
ENGLISH
Introduction Introduction
Playable Discs and Files
This unit is compatible to play back the following discs. To play back a BD or DVD, make sure that it meets the requirements for region codes and color systems as described on page 5. You can play back discs that have the following logos on the disc. Other disc types are not guaranteed to play back.
Playable discs Logos
Blu-ray Disc
-BD-Video
- BD-RE (ver.2.1) (Recorded in BDMV format)
- BD-R (ver.1.1/1.2/1.3) (Recorded in BDMV format) (Unclosed discs may not be played back.)
DVD-Video
DVD-RW (Finalized discs only)
DVD-R DVD-R DL
CD-DA (audio CD)
CD-RW
CD-R
Kodak Picture CD
DTS-CD (5.1 Music Disc)
(Finalized discs only)
Playable files Logos Media
DVD-RW/-R SD Memory Card
AVCHD
(including SDHC) miniSD Card microSD Card
BD-RE/-R DVD-RW/-R
DivX
®
CD-RW/-R
MP3
BD-RE/-R DVD-RW/-R
Windows Media™ Audio
CD-RW/-R SD Memory Card (including SDHC) miniSD Card
JPEG
microSD Card
Note
• ABOUT DIVX VIDEO: DivX® is a digital video format created by DivX, Inc. This is an official Divx Certified device that plays DivX video. Visit www.divx.com for more information and software tools to convert your files into DivX video.
• ABOUT DIVX VIDEO-ON-DEMAND: This DivX Certified must be registered in order to play DivX Video-on-Demand (VOD) content. To generate the registration code, locate the DivX VOD section in the device setup menu. Go to vod.divx.com with this code to complete the registration process and learn more about DivX VOD.
• Discs containing the DivX® files with the DivX®GMC (Global Motion Compensation) playback feature, which is DivX supplemental function, cannot be played back on this unit.
• This unit cannot play back the disc contents protected by Windows Media™ Digital Rights Management (DRM).
• “WMA” (Windows Media™ Audio) is an audio codec developed by Microsoft® in the United States of America.
®
device
®
Readable cards Playable files / data
SD Memory Card (8MB - 2GB) AVCHD, MP3, Windows Media™ SDHC Memory Card (4GB - 8GB) miniSD Card (8MB - 2GB)
microSD Card (8MB - 2GB)
Audio, JPEG, Picture-in-picture commentary, subtitles or other extras for BD-ROM ver. 2 (Profile
2.0/ Profile 1.1)
Note for SD Memory Cards
• Do not remove the SD Memory Card or turn the unit to the standby mode while the contents of the card is in playback. It may result in malfunction or loss of the card’s data.
• Please keep the SD Memory Cards in their cases when you are not using them.
• Do not try to open or modify the card.
• Do not touch the terminal surface with your fingers or any metals.
• Do not attach additional labels or stickers to cards.
• Do not remove the label of the SD Memory Cards.
• This unit supports SD Memory Card with FAT12/FAT16 file system, and SDHC Memory Card with FAT32 file system.
• This unit may not read the SD Memory Cards formatted on computer. If that is the case, please reformat the SD Memory Cards on this unit and try again.
• This unit does not support mini SDHC and micro SDHC Memory Card.
• For miniSD Card and microSD Card adapter is necessary.
miniSD Card Adapter
miniSD Card
• Portions of this product are protected under copyright law and are provided under license by ARIS/SOLANA/4C.
microSD Card Adapter
microSD Card
Introduction Connections Playback Function Setup Others
4
ENGLISH
ENGLISH
Introduction Introduction
Introduction Connections Playback Function Setup Others
The following discs will not play back on this unit.
BD and DVD are recorded in different color systems throughout the world. The most common color system is NTSC (which is used primarily in the United States and Canada).
This unit uses NTSC, so BD or DVD you play back must be recorded in the NTSC system. You cannot play back BD or DVD recorded in other color systems.
Unplayable Discs
• BD-RE (ver.1.0) (BD-disc with cartridge)
• BD-RE (ver.2.1) (Recorded in BDAV format)
• BD-R (ver.1.1/1.2/1.3) (Recorded in BDAV format)
• BD that contains AVCHD files
• Multi-session burn BD/DVD with DivX
®
files
• Multi-session burn BD-RE/-R with MP3/Windows Media™ Audio/ JPEG files
• BD/DVD hybrid disc (e.g. Total Hi Def hybrid disc)
•BD-Video that does not include “A” on its region code.
• DVD-Video that does not include either “1” nor “ALL” on its region code.
• DVD-ROM/RAM (For DVD-ROM discs, data files in DivX
®
3.11, 4.x,
5.x and 6.x can be played)
• DVD-RW/-R recorded in non-compatible recording format
• CD-ROM (Data files in DivX
®
3.11, 4.x, 5.x and 6.x can be played)
• CDV (Only the audio part can be played)
• CD-G (Only the audio signals can be output)
• Compact Disc-Interactive (CD-I)
• Video Single Disc (VSD)
• Video CD, Super Video CD
• Super audio CD (Only the sound on the CD layer can be heard. The sound on the high-density super audio CD layer cannot be heard.)
•DVD-Audio
•HD DVD
• Disc with recording area less than 55mm in diameter
• Unauthorized disc (Pirated disc)
• Unfinalized disc
Color Systems
Region Codes
This unit has been designed to play back BD with region A and DVD-Video with region 1. You cannot play back BD or DVD-Video that are labeled for other regions. Look for the symbols on the right on your BD or DVD-Video. If these region symbols do not appear on your BD or DVD-Video, you cannot play back the disc in this unit. The letter or number inside the globe refers to region of the world. A BD or DVD-Video labeled for a specific region can only play back on the unit with the same region code.
BD-Video
DVD-Video
Structure of Disc/SD Memory Card Contents
The contents of disc are generally divided into titles. Titles may be further subdivided into chapters.
BD/DVD/AVCHD
title 1 title 2
chapter 1 chapter 2 chapter 1 chapter 2 chapter 3
Audio CDs are divided into tracks.
track 1 track 2 track 3 track 4 track 5
Data discs or SD Memory Cards containing DivX® (in discs only)/ MP3/Windows Media™ Audio/JPEG are divided into folders, and the folders are subdivided into files.
DivX®/MP3/Windows Media™ Audio/JPEG
folder (group) 1 folder (group) 2
group(folder)1 group(folder)2
file (track) 1 file (track) 2 file (track) 3 file (track) 4 file (track) 5
Audio CD
audio CD
MP3, WMA, JPEG, DivX®
Symbols Used in this User Guide
To specify for which media type each function is, we put the following symbols at the beginning of each item to operate.
Symbol Description
BD-V
DVD-V
DVD-VR
CD
AVCHD
DivX
MP3
WMA
JPEG
If you do not find any of the symbols listed above under the function heading, the operation is applicable to all media.
Button name only:
Description refers to BD-Video and BD-RE (ver. 2.1)/ BD-R (ver.1.1/1.2/1.3) recorded in BDMV format
Description refers to DVD-Video and DVD-RW/-R recorded in video mode
Description refers to DVD-RW/-R recorded in VR mode
Description refers to audio CD and DTS-CD
Description refers to DVD-RW/-R and SD Card with AVCHD files
Description refers to BD-RE/-R, DVD-RW/-R and
®
CD-RW/-R with DivX
®
files
Description refers to BD-RE/-R, DVD-RW/-R, CD-RW/-R and SD Memory Card with MP3 files
Description refers to BD-RE/-R, DVD-RW/-R, CD-RW/-R and SD Memory Card with Windows Media™ Audio files
Description refers to BD-RE/-R, DVD-RW/-R, CD-RW/-R and SD Memory Card with JPEG files
About the button names in this explanation
< > : Buttons on the main unit [ ] : Buttons on the remote control
Buttons on the main unit and remote control
5
ENGLISH
ENGLISH
Introduction Introduction
About the Remote Control
Loading the Batteries
Using a Remote Control
Keep in mind the following when using the remote control:
• Make sure that there are no obstacles between the remote control and infrared sensor window on the unit.
A Open the battery
compartment cover.
B Insert two “AA” (R6)
batteries, with each one oriented correctly.
• Remote operation may become unreliable if strong sunlight or fluorescent light is shining on infrared sensor window of the unit.
• Remote control for different devices can interfere with each other. Avoid using remote control for other equipment located close to the unit.
• Replace the batteries when you notice a fall off in the operating
• At this point the new signal code of the unit is effective. Please change the signal code of the remote control to match to the signal code of the unit with following procedure.
Change the signal code of the remote control
Set to “BD1”:
Press and hold down both C and [1] on the remote control for at least five seconds.
Set to “BD2”:
Press and hold down both C and [2] on the remote control for at least five seconds.
range of the remote control.
• The maximum operable ranges from the unit are as follows.
- Line of sight: approx. 16 feet (5m)
- Either side of the center: approx. 16 feet (5m) within 30°
C Close the cover.
• If the signal code does not match, the signal code of the remote control will be displayed on the front panel display.
• The default setting and the setting after you change the batteries is “BD1”.
• If the code setting on the unit is “BD1”, and the setting on the remote control is “BD2”, “BD2” is shown on the front panel display.
Cautions on Batteries
• Use “AA” (R6) batteries in this remote control.
• Replace the batteries with new ones approximately once a year, though this depends on the frequency with which the remote control is used.
• If the remote control does not operate within a close proximity of the main unit, replace the batteries with new ones, even if less than a year has passed.
• The included batteries serve only for verifying operation. Replace them with new batteries as soon as possible.
• When inserting the batteries, be careful to do so in the proper direction, following the and marks in the remote control’s battery compartment.
• To prevent damage or battery fluid leakage:
- Do not mix a new battery with an old one.
- Do not mix two different types of batteries such as alkaline
and manganese.
- Do not short-circuit, disassemble, heat or dispose of
batteries in flames.
• Remove the batteries when not planning to use the remote control for a long period of time.
• If the batteries should leak, carefully wipe off the fluid from the inside of the battery compartment, then insert new batteries.
16 feet (5m) 30° 16 feet (5m) 16 feet (5m) 30°
Changing the Signal Code of a Remote Control
To avoid the other Marantz’s BD players responding the remote signal of this unit, you can change the signal code of the remote control. If the signal code of the remote control does not match to the signal code of the unit, you cannot control the unit with the remote control.
Change the signal code of the unit
1) In stop mode, press [SETUP].
2) Use [Y / Z] to select , then press [ENTER].
3) Use [Y / Z] to select , then press [ENTER].
4) Use [U / V] to select “Remote Control Setting”.
5) Press [ENTER] to select “BD1” or “BD2”.
30°30°
Others
Remote Control Setting BD1 HDMI CEC On Media Select Disc Network Connection Enable(Easy) Network Update
T Button illustrations used in this manual for operation
explanation are for the Remote Control Unit. You can operate the unit using the button of the same name on the front panel of the unit.
Introduction Connections Playback Function Setup Others
6) Press [SETUP] to exit.
6
ENGLISH
ENGLISH
Introduction Introduction
Introduction Connections Playback Function Setup Others
Part Names and Functions
Front Panel
910111287
2
1
4
53
The unit can also be turned on by pressing the buttons with circled numbers.
1. STANDBY indicator
This indicator lights up in red in standby mode and turns off when the power is on.
2. POWER ON/STANDBY button
Press to turn on the unit, or to turn the unit to the standby mode. (In standby mode, this unit still consumes small amount of power. To completely shut down the unit, you must unplug the AC cord.)
3. HDMI RESOLUTION button
Press to set the HDMI jack’s video signal
8. A (OPEN/CLOSE) button
Press to open or close the disc tray.
9. Disc tray
Place a disc when opening the disc tray.
10. B (PLAY) button
Press to start or resume playback.
11. C (STOP) button
Press to stop playback.
12. F (STILL/PAUSE) button
Press to pause playback.
output mode.
4. Infrared sensor window
Receives signals from your remote control so that you can control the unit from a distance.
5. Display
Refer to “Front Panel Display” on page 9.
6. SD card slot
Insert an SD Memory Card, and play back the contents in it.
7. H / G (SKIP DOWN/UP) button
Press to skip down/up titles/chapters/tracks/ files.
6
Rear Panel
AC IN
NETWORK
1. AC IN Terminal
Use to connect the AC cord to supply the power.
2. DIGITAL OUT (COAXIAL) jack
Use digital audio coaxial cable to connect to an AV receiver, Dolby Digital decoder or other device with a digital audio coaxial input jack.
3. COMPONENT VIDEO OUT jacks
Use a component video cable to connect to a display device with component input jacks.
4. VIDEO OUT jack
Use an RCA video cable to connect to a TV monitor, AV receiver or other device.
5. FLASHER IN / OUT jacks
This Input terminal is equipped for controlling this unit by the external Infrared (IR) control device. Connect the IR control signal from a Keypad, IR repeater, etc. The Output terminal repeats the IR signal which was fed into the IR Flasher Input terminal for another device.
2 3 41 5
DIGITAL OUT
COMPONENT VIDEO OUT
COAXIAL
HDMI OUT
VIDEO OUT
87
6. 2ch AUDIO OUT jacks
Use an RCA audio cable to connect these jacks to the 2-channel audio input jacks of your amplifier with 2- channel input terminals.
7. NETWORK Terminal
Use to connect a telecommunications equipment with LAN cable.
8. HDMI OUT jack
Use an HDMI cable to connect to a display with an HDMI input jack.
Note
• Do not touch the inner pins of the jacks on the rear panel. Electrostatic discharge may cause permanent damage to the unit.
FLASHER IN
6
OUT
2ch AUDIO OUT
LR
7
ENGLISH
ENGLISH
Introduction Introduction
Remote Control
34
1
2
33
3
4
32
5
6
7
31
8
10
9
30
11
12
14
16
18
20
13
15
17
19
29
28
27
26
25
24
21
22
The unit can also be turned on by pressing the buttons with circled numbers.
23
1. POWER ON button
• Press to turn the unit on.
2. POWER OFF button
• Press to turn the unit to standby mode.
3. A-B REPEAT button
• Press to mark a segment between A and B for A-B repeat playback.
4. REPEAT button
• Press to select the repeat mode.
5. RANDOM button
• Press to display the random playback screen for shuffling the playback order of tracks/files.
6. ZOOM button
• During playback, press to enlarge the picture on the screen.
7. CLEAR button
• Press to clear the information once entered, to clear the marker settings, or to cancel the programming for CD, etc.
8. RED/GRN/BLU/YEL button
• Press to select item on some BD menus.
• When file list / thumbnail list is shown, press to switch between pages.
9. TOP MENU button
• Press to display the top menu.
10. Cursor U / V / Y / Z buttons
• Press to select items or settings.
11. ENTER button
• Press to confirm or select menu items.
12. SETUP button
• Press to display the setup menu.
13. SUBTITLE button
• Press to display the subtitle menu.
14. ANGLE button
• Press to access various camera angles on the disc.
• Press to rotate the JPEG/Kodak Picture images clockwise by 90 degrees.
15. PURE DIRECT button
• Press to stop output of video signals, etc., and output only the analog audio signals to achieve high quality sound from analog audio outputs.
16. DISPLAY button
• Press to display the On-Screen display menu.
17. SKIP H button
• During playback, press to return to the beginning of the current title, chapter, track or file.
18. SKIP G button
• During playback, press to skip the next chapter, track or file.
19. STOP C button
• Press to stop playback.
• Press to exit from the title menu.
20. REW h button
• During playback, press to fast reverse the playback.
21. HDMI RESOLUTION button
• Press to set the HDMI jack’s video signal output mode.
22. INPUT U / V buttons
• These buttons are used to switch the input when using one of the supported Marantz amplifiers. However, this function may not work with some of the older models.
23. VOLUME +/– buttons
• This button can be used to adjust the volume of devices compatible with Marantz amplifiers that come with a remote controller.
24. STILL/PAUSE F button
• Press to pause playback.
• When playback is in pause, press repeatedly to forward the playback step by step.
25. FFW g button
• During playback, press to fast forward the playback.
• When playback is in pause, press to slow forward the playback.
26. PLAY B button
• Press to start playback or resume playback.
27. MODE button
• During playback, press to display the picture adjustment menu, and dialog speed.
• During the JPEG playback, press to display menus for changing the visual effect for switching the image or changing the size of the image.
• In stop mode with BD inserted, press to display a menu for setting the BD audio mode.
• During playback of BD, DVD, audio CD, AVCHD, DivX or Windows Media™ Audio, press to display a menu for setting the virtual surround.
• During BD playback, press to turn the picture-in-picture feature on or off (only applicable to BD-Video which supports the PIP (BONUSVIEW) function).
• In stop mode with audio CD, or disc with MP3, Windows Media™ Audio, JPEG files inserted, press to display menus for program and random playback.
28. AUDIO button
• Press to display the audio menu.
29. RETURN button
• Press to return to the previously displayed menu screen.
®
, MP3
Introduction Connections Playback Function Setup Others
8
ENGLISH
ENGLISH
Introduction Introduction
30. POP UP MENU / MENU button
Introduction Connections Playback Function Setup Others
31. SEARCH MODE button
32. Number buttons
33. OPEN/CLOSE A button
34. DIMMER button
• Press to display the pop-up menu/disc menu/file list.
• Press to change “Original” and “Playlist” on the TV screen.
• Press to display the search menu.
• Press to enter the title/chapter/track/file numbers.
• Press to open or close the disc tray.
• Press to adjust the brightness of the front panel display.
Front Panel Display
1 2
Note
[ZOOM] is not available for BD and AVCHD.
[RANDOM] is not available for BD, DVD, AVCHD and DivX
* Brightness of the display can be adjusted. Refer to “Panel Display” in “Function Setup” on page 37.
®
.
1) Displays playback status icon. Refer to the table below.
2) Displays various kinds of information such as title number, elapsed time, repeat mode, etc.
Playback status icon
Disc SD Memory Card
Playback is in progress
Stop mode
Pause mode
Fast forward mode
Fast reverse mode
Slow forward mode
(for AVCHD only)
Appears while repeat function is set
Mode
Adjusting the Brightness of the Display
You can adjust the brightness of the display by the pressing [DIMMER] repeatedly. The brightness changes as bright A dimmer A auto each time you press [DIMMER]. If you select auto, the display gets dimmer during playback.
Note
[DIMMER] is not available when the setup menu is displayed.
9
ENGLISH
ENGLISH
Introduction Introduction
Examples of Displays during Operation
Display Description
Power on
Standby mode
Tray open
Tray is closing
Loading the disc
No disc inserted
This unit cannot read the disc or SD Memory Card inserted.
Stop mode
HDMI output mode (480i) is selected.
HDMI output mode (480p) is selected.
HDMI output mode (720p) is selected.
HDMI output mode (1080i) is selected.
HDMI output mode (1080p) is selected.
Introduction Connections Playback Function Setup Others
HDMI output mode (1080p24 frame) is selected.
HDMI output mode (Source Direct) is selected.
Pure direct mode is set to pure direct off.
Pure direct mode is set to video signal off.
Pure direct mode is set to front panel display off.
Pure direct mode is set to video signal and front panel display off.
Appears when the connected display device or other device does not support HDCP.
Note
• When playing back the disc that contains more than 100 titles, display of the chapter and time on the front panel display will be moved a few dots to the right.
10
ENGLISH
ENGLISH
Introduction Connections Playback Function Setup Others
Connect the BD5004 as follows before using. Make connections according to the equipment you are connecting. Some BD5004 settings may be necessary depending on the connection method. Check each connection item for more information.
Connections
Home theater playback
1
- Playing back using multi-channel system
BD5004
Multi-channel Audio + Video
• HDMI connection
“Connecting to a Display Device and an Amplifier/ Receiver with HDMI Cable” (page 12)
or
Multi-channel Audio
• Digital audio connection
“Digital Connection to an AV Amplifier with Built-in Decoder” (page 14)
Video
•Connecting to a TV (VIDEO OUT/COMPONENT VIDEO OUT)
: page 12
Playing back with a direct connection to a TV
2
BD5004
Audio + Video
• Connecting to a Display Device with HDMI Cable
or
Audio
• Connecting to a TV (2ch AUDIO OUT) : page 12
Video
•Connecting to a TV (VIDEO OUT/COMPONENT VIDEO OUT)
Playing back 2-channel audio
3
BD5004
: page 12
: page 12
Using BD-Live function or updating the software version of BD5004
4
• NETWORK connection
“Network Connection with LAN” (page 15)
• Connecting the AC cord : page 16
BD5004
• 2ch audio connection
“Connection to a Device with 2-channels of Analog Audio Inputs” (page 15)
11
ENGLISH
ENGLISH
F
N
D
D
Connections
Connecting to a TV
Make one of the following connections, depending on the capabilities of your existing device.
Method 1 Method 2
analog audio
display device
AUDIO IN
LR
RCA
audio
cable
and or
this unit
LASHER
OUT
2ch AUDIO OUT
LR
2ch AUDIO OUT
LR
2ch AUDIO OUT VIDEO OUT
Supplied cables used in this connection are as follows:
• RCA audio cable (L/R) x 1
• RCA video cable x 1 Please purchase the rest of the necessary cables at your local store.
standard picture
VIDEO
IN
RCA video cable
VIDEO OUT
better picture
COMPONENT
VIDEO IN
Y
(Green)
B/CB
P
(Blue)
PR/C
R
(Red)
component video cable
(Red) (Blue) (Green)
COMPONENT VIDEO OUT
PB/C
B
/C
R
R
P
Y
COMPONENT VIDEO OUT
Connections
Connecting to a Display Device with HDMI Cable
Connecting this unit to device with an HDMI jack using an HDMI cable enables digital transfer of both digital video signals and multi-channel audio signals. After making the connection, please make HDMI settings on setup menu according to your display device. Refer to pages 31-33.
this unit
NETWORK
HDMI cable
DIGITAL OUT
COAXIAL
COMPONENT VI
HDMI OUT
best audio and picture
A display device with an HDMI compatible port
Method 3
display device
AC IN
To HDMI Input jack
Cables not included.
Please purchase the necessary cables at your local store. Use a cable on which the HDMI logo is indicated (a certified HDMI product) for connection to the
HDMI connector. Normal playback may not be possible when using a cable other than one on which the HDMI logo is indicated (a non-HDMI-certified product).
Connecting to a Display Device and an Amplifier/Receiver with HDMI Cable
Connecting this unit to display device and an amplifier/receiver with an HDMI jack using HDMI cables enables digital surround sound with high quality video.
Front Speaker (left)
Center
Speaker
Front Speaker (right)
Introduction Connections Playback Function Setup Others
Note
• Connect this unit directly to the TV. If the RCA audio/video cables are connected to a VCR, pictures may be distorted due to the copy protection system.
display device
HDMI IN HDMI OUT
amplifier
HDMI IN
this unit
DIGITAL OUT
AC IN
COMPONENT VI
COAXIAL
NETWORK
HDMI OUT
• If the display device to which the player is to be connected is compatible with progressive scan video, connect to the component video input.
• This unit’s COMPONENT VIDEO OUT jacks are compatible for 480i/480p/720p/1080i video resolution. If the connected display device is not compatible for 480p/720p/1080i video resolution, set “Component Output” to “480i”.
• If the picture is not output properly to the display device because of the “HDMI Video Resolution” or “Component Output” setting, press and hold B on the front panel for more than 5 seconds. The “HDMI Video Resolution” setting will be reset to the default automatically.
• If you are using HDMI connection and set “HDMI Video Resolution” to “Source Direct”, “1080p” or “1080p24”, picture may not be output properly to the display device. In that case, set “HDMI Video Resolution” to “480i”, “480p”, “720p” or “1080i”.
Surround Speaker (left) Surround Speaker (right)
HDMI cable
Surround back (For
7.1-channel) (left)
Surround back (For
7.1-channel) (right)
HDMI cable
Subwoofer
Cables not included.
Please purchase the necessary cables at your local store.
12
ENGLISH
ENGLISH
Connections Connections
Introduction Connections Playback Function Setup Others
Press [HDMI RESOLUTION] to select the HDMI output mode. HDMI video resolution changes as following.
HDMI Output Mode and Actual Output Signals
Front Panel Display HDMI Video Resolution
480 Interlaced
Press [HDMI RESOLUTION]
480 Progressive
Press [HDMI RESOLUTION]
720 Progressive
Press [HDMI RESOLUTION]
1080 Interlaced
Press [HDMI RESOLUTION]
1080 Progressive
Press [HDMI RESOLUTION]
1080 Progressive 24 frame
Press [HDMI RESOLUTION]
Source Direct
Press [HDMI RESOLUTION]
Note
• You can change the HDMI output mode with [HDMI RESOLUTION] during playback as well. (This
is not available during BD/AVCHD playback.)
• Video and audio signals may be distorted temporarily when switching to/from the HDMI output mode.
• You can also change the HDMI output mode from “HDMI Video Resolution” in the “Video” menu on the setup menu. Refer to page 32.
• In order to get natural and high quality film reproduction of 24-frame film material, use HDMI cable (High Speed HDMI cable is recommended) and select “1080p24”, “Auto” or “Source Direct” if the connected display device is compatible with 1080p24 frame input.
• For AVCHD and DivX device is compatible with 1080p24 frame input and “HDMI Video Resolution” is set to “1080p24”, “Auto” or “Sou rce Direct ”.
• When “HDMI Video Resolution” is set to “1080p”, “1080p24” or “Source Direct”, the “Component Output” will be set to “480i” automatically.
• If the video is not properly from HDMI OUT jack after you set the “HDMI Video Resolution” setting, change the HDMI video resolution to the compatible resolution by pressing [HDMI RESOLUTION] or press and hold B on the front panel for more than 5 seconds to reset the setting.
• “HDMI Deep Color” is available only when the display device is connected by HDMI cable and supports HDMI Deep Color.
• For “Auto” in “HDMI Deep Color”, using the High Speed HDMI cable is recommended.
®
, 24-frame film material will be output as 60 frame, even if the connected
Audio Setting
When using HDMI connections make the “HDMI Audio Out” settings in the “Audio” menu on the setup menu according to the specifications of the device or monitor to be connected.
Device to be connected “HDMI Audio Out” setting Output HDMI audio signal
Device compatible with DTS, DTS-HD, Dolby Digital, Dolby Digital Plus or Dolby TrueHD decoding
HDMI Multi(Normal) Dolby Digital, Dolby Digital Plus,
Dolby TrueHD, DTS, or DTS-HD bitstream are output from HDMI OUT. Make the speaker settings on the connected AV amplifier, etc.
Device compatible with 3 or more channels of audio inputs (not DTS, DTS-HD, Dolby Digital, Dolby Digital Plus or Dolby TrueHD compatible)
HDMI Multi(LPCM) Multi-channel audio signals are
output from the HDMI OUT. Make the speaker settings with the speaker setting items appear after you select “HDMI Multi(LPCM)”. Refer to page 33.
Device compatible with 2-channel audio input or device not compatible with audio input
HDMI connection to a display device, and digital audio connection (coaxial) to an AV amplifier.
HDMI 2ch Down-mixed 2-channel audio
signals are output from HDMI OUT.
Audio Mute HDMI audio will be muted, and
Dolby Digital/DTS bitstream or PCM will be output from DIGITAL OUT depending on the “Digital Out” setting. Refer to page 14.
Audio signals output from HDMI OUT
Disc type Audio recording
format
HDMI Multi(Normal) HDMI Multi(LPCM) HDMI 2ch
Dolby Digital Dolby Digital Multi PCM 2ch Downmix PCM
BD-Video
Dolby Digital Plus
Dolby TrueHD
DTS DTS Multi PCM 2ch Downmix PCM DTS-HD
Dolby Digital Plus*
Dolby TrueHD*
DTS-HD*
3
PCM Multi PCM Multi PCM 2ch Downmix PCM Dolby Digital Dolby Digital Multi PCM 2ch Downmix PCM
DVD-Video
DTS DTS Multi PCM 2ch Downmix PCM PCM 2ch PCM 2ch PCM 2ch PCM
DTS-CD DTS Multi PCM 2ch Downmix PCM
AVCHD
®
DivX
audio CD/ MP3/ Windows
Dolby Digital Dolby Digital Multi PCM 2ch Downmix PCM PCM Multi PCM Multi PCM 2ch Downmix PCM Dolby Digital Dolby Digital Multi PCM 2ch Downmix PCM MP3/ MP2 2ch PCM 2ch PCM 2ch PCM
2ch PCM 2ch PCM 2ch PCM
Media™ Audio
“HDMI Audio Out” setting
1
Multi PCM*
2
Multi PCM*
Multi PCM*
4
5
6
2ch Downmix PCM*
2ch Downmix PCM*
2ch Downmix PCM*
4
5
6
13
ENGLISH
ENGLISH
Connections
• If “BD Audio Mode” is set to “HD Audio Output” or the BD title does not have secondary or interactive audio, the audio will be output as shown in the table.
• If the “BD Audio Mode” is set to “Mix Audio Output” and the BD title has secondary or interactive audio, the audio will be output as follows:
1
*
Dolby Digital or Multi PCM (Only the independent substream is decoded.)
2
Dolby Digital or Multi PCM (Only the Dolby Digital substream is decoded.)
* *3DTS or Multi PCM (Only the core substream is decoded.)
4
As shown in the table (Only the independent substream is decoded.)
*
5
As shown in the table (Only the Dolby Digital substream is decoded.)
*
6
As shown in the table (Only the core substream is decoded.)
*
• If the connected device is not compatible with the HDMI BITSTREAM, audio will be output as Multi PCM or 2ch Downmix PCM depending on the capability of the connected device, even if you select “HDMI Multi(Normal)” in“HDMI Audio Out” setting. Refer to page 33.
Copyright protection system
To play back the digital video images of a BD/DVD via an HDMI connection, it is necessary that both the unit and the display device (or an AV amplifier) support a copyright protection system called HDCP (high-bandwidth digital content protection system). HDCP is copy protection technology that comprises data encryption and authentication of the connected AV device. This unit supports HDCP. Please read the user guide of your display device (or AV amplifier) for more information.
* HDMI: High-Definition Multimedia Interface
Note
• When using HDCP-incompatible display device, the image will not be viewed properly.
• The audio signals from the HDMI jack (including the sampling frequency, the number of
channels and bit length) maybe limited by the device that is connected.
• Among the monitors that support HDMI, some do not support audio output (e.g. projectors). In
connections with device such as this unit, audio signals are not output from the HDMI output jack.
Digital Connection to an AV Amplifier with Built-in Decoder
audio
digital audio coaxial input jack
DIGITALAUDIO INPUT
COAXIAL
digital audio coaxial cable
DIGITAL OUT
COMPONENT VIDEO OUT
FLASHER
AC IN
NETWORK
VIDEO OUT
COAXIAL
HDMI OUT
IN
this unit
DIGITAL OUT
OUT
2ch AUDIO OUT
COAXIAL
FL
LR
Audio signals output from DIGITAL OUT (COAXIAL)
When both HDMI and DIGITAL OUT is connected to other devices, the audio signals currently output from the HDMI OUT will be output from the DIGITAL OUT jack as well, except that HDMI 2ch signal will be output from HDMI OUT jack, when connected device does not support Dolby Digital and DTS.
< When HDMI is not connected or “Audio Mute” is selected···>
When HDMI is not connected or the “Audio Mute” is selected in “HDMI Audio Out” setting, the audio
Connections
signals output from DIGITAL OUT changes depending on the “Digital Out” setting. Refer to the following table.
To set “Digital Out”, press [SETUP], then select “Quick” A “HDMI Audio Out” A “Audio Mute” or “Custom” A “Audio” A “HDMI Audio Out” A “Audio Mute”.
Disc type Audio recording format “Digital Out” setting
Bitstream LPCM
Dolby Digital Dolby Digital 2ch Downmix PCM
1
2
3
BD-Video
Dolby Digital Plus Dolby Digital
Dolby TrueHD Dolby Digital
2ch Downmix PCM*
2ch Downmix PCM* DTS DTS 2ch Downmix PCM DTS-HD DTS
2ch Downmix PCM* PCM 2ch Downmix PCM 2ch Downmix PCM Dolby Digital Dolby Digital 2ch Downmix PCM
DVD-Video
DTS DTS 2ch Downmix PCM PCM 2ch PCM 2ch PCM
DTS-CD DTS 2ch Downmix PCM
AVCHD
®
DivX
Dolby Digital Dolby Digital 2ch Downmix PCM PCM 2ch Downmix PCM 2ch Downmix PCM Dolby Digital Dolby Digital 2ch Downmix PCM MP3/ MP2 2ch PCM 2ch PCM
audio CD/ MP3/ Windows Media™ Audio 2ch PCM 2ch PCM
• This table applies only when HDMI is not connected or the “Audio Mute” is selected in “HDMI Audio Out” setting.
• If “BD Audio Mode” is set to “HD Audio Output” or the BD title does not have secondary or interactive audio, the audio will be output as shown in the table.
• If the “BD Audio Mode” is set to “Mix Audio Output” and the BD title has secondary or interactive audio, the audio will be output as follows:
1
Only the independent substream is decoded.
*
2
Only the Dolby Digital substream is decoded.
*
3
Only the core substream is decoded.
*
Note
• In order to output PCM signal from DIGITAL OUT jack while outputting the HDMI audio signal,
set “BD Audio Mode” to “Mix Audio Output” and set “HDMI Audio Out” to “HDMI Multi(LPCM)”.
Cables not included.
Please purchase the necessary cables at your local store.
Introduction Connections Playback Function Setup Others
14
ENGLISH
ENGLISH
Connections Connections
Introduction Connections Playback Function Setup Others
Connection to a Device with 2-channels of Analog Audio Inputs
audio
Stereo component
AUDIO IN
L R
RCA audio cable
AC IN
NETWORK
2ch AUDIO OUT
DIGITAL OUT
COMPONENT VIDEO OUT
COAXIAL
HDMI OUT
LR
Network Connection with LAN
• You can use a disc which offers BD-Live function by connecting the unit to the Internet. (For BD-Live information, please refer to page 29.)
this unit
FLASHER
VIDEO OUT
IN
OUT
2ch AUDIO OUT
LR
Te le co m mu n ic a ti o ns
equipment (modem, etc.)
Hub or broadband router
Supplied cables used in this connection are as follows:
• RCA audio cable (L/R) x 1
Note
• When connecting to a 2-channel audio stereo device, use the 2ch AUDIO OUT jacks. For software recorded in multi-channel, analog signals that have been down-mixed into 2 channels are output.
LAN
WAN LAN
12345
LAN cable
LAN cable
Internet
Telecommunications
equipment (modem, etc.)
this unit
DIGITAL OUT
NETWORK
COMPONENT VIDEO OUT
COAXIAL
HDMI OUT
AC IN
VIDEO OUT
NETWORK
FLASHER IN
OUT
2ch AUDIO OUT
LR
No supplied cables are used in this connection:
Please purchase the necessary cables at your local store.
Note
• After connecting to the Internet, set up necessary network settings.
• Do not insert any cable other than a LAN cable to the NETWORK terminal to avoid damaging the unit.
• If your telecommunications equipment (modem, etc.) does not have broadband router functions, connect a broadband router.
• If your telecommunications equipment (modem, etc.) has broadband router functions but there is no vacant port, use a hub.
• For a broadband router, use a router which supports 10BASE-T/100BASE-TX.
• Do not connect your PC directly to the NETWORK terminal of this unit.
15
ENGLISH
ENGLISH
T
Connections
Connecting the AC cord
After you made all necessary connections, connect the AC cord to the AC IN. Then connect the AC cord to the AC outlet.
AC outlet
AC 120V, 60 Hz
AC IN
AC cord
NETWORK
DIGITAL OUT
COAXIAL
COMPONENT VIDEO OU
HDMI OUT
Supplied cables used in this connection are as follows:
• AC cord x 1
Note
• Insert the plugs securely. Incomplete connections will result in the generation of noise.
Connections
Introduction Connections Playback Function Setup Others
16
ENGLISH
ENGLISH
Introduction Connections Playback Function Setup Others
Playback
Disc playback
Direct Playback (BD/DVD-Video/AVCHD) : page 17Playing Back a VR mode DVD-RW/-R : page 18Playing Back an Audio CD or a Disc with
DivX®/MP3/Windows Media™ Audio/JPEG File : page 26
Kodak Picture CD : page 28
SD Card playback
Reading the SD Memory Card : page 28
Operations Using Disc Menu, Title Menu, and Popup Menu : page 18
NOTE
may appear at the top-right on the screen when the operation is prohibited by the disc or this unit.
• During the playback of 2-layered disc, pictures may stop for a moment. This happens when the 1st layer switches to the 2nd layer. This is not a malfunction.
• The operation may vary when you play back with disc menu. Refer to the manual accompanying the disc for details.
AC
<POWER ON/STANDBY>
About the button names in this explanation
< > : Buttons on the main unit [ ] : Buttons on the remote control
Button name only:
Buttons on the main unit and remote control
B
[POWER OFF]
[POWER ON]
C
Turning the Power On
Press [POWER ON] or <POWER ON/STANDBY> to turn on the unit.
The power indicator turns off when the power is on.
A
[U / V / Y / Z]
[ENTER]
B
Turning the unit to the standby mode
Press [POWER OFF] or <POWER ON/STANDBY> to turn the unit to the standby mode. The power indicator lights red.
Note
• Power continues to be supplied to some of the circuitry even when the power is in the standby mode. When leaving home for long periods of time or when traveling, unplug the AC cord from the AC outlet.
Direct Playback
BD-V
1 2
DVD-V
Turn on the power of this unit. (Refer to “Turning the Power On” on this page.)
Turn on the display device and select the appropriate input on the device to which the unit is connected.
Press A to open the disc tray.
3
Place the disc on the disc tray with its label side
4
facing up.
Press A to close the disc tray.
5
Some discs may start playback automatically.
Press B to start playback.
6 7
Menu screen may appear. In this case, use [U / V / Y / Z] to select the desired item, then press [ENTER].
Press C once to stop playback temporarily.
Refer to “Resume Playback” on page 18.
To eject the disc:
Press A to open the disc tray, then remove the disc before turning the unit to the standby mode.
DVD-VR
It may take a while to load
AVCHD
Align the disc to the disc tray guide.
the disc.
17
ENGLISH
ENGLISH
Playback Playback
Pause
1) During playback, press F.
Playback will be paused.
F
2) Press B to return to normal playback.
[TOP MENU]
[POP UP MENU / MENU]
[U / V / Y / Z]
[ENTER]
Note
• If the feature is not available, may appear on the TV screen.
• Contents of menus and corresponding menu operations may vary among discs. Refer to the manual accompanying the disc for details.
• BD/DVD/AVCHD menu varies depending on discs.
Introduction Connections Playback Function Setup Others
C
h
B
g
F
Operations Using Disc Menu, Title Menu, and Popup Menu
BD-V
DVD-V
Many of BD and DVD disc contains Disc menu (DVD), Title menu (BD/DVD/AVCHD) or Pop-up menu (BD-Video) which describes the contents of the disc, or a disc menu, which guides you through the available functions in the disc. The contents of the menus may differ depending on the discs.
Disc menu (DVD)
1) Press [POP UP MENU / MENU].
• The disc menu will appear.
2) Use [U / V / Y / Z] to select an item, then press [ENTER].
Title menu (BD/DVD/AVCHD)
1) Press [TOP MENU].
2) Use [U / V / Y / Z] to select an item, then press [ENTER].
Pop-up menu (BD-Video)
• This is a special feature available for some BD. When you
press [POP UP MENU / MENU], a menu pops out on the screen while the contents still play back.
1) During BD playback, press [POP UP MENU / MENU].
2) Use [U / V / Y / Z] to select an item, then press [ENTER].
AVCHD
Playing Back a VR mode DVD-RW/-R
DVD-VR
When you are playing back a VR mode DVD-RW/-R, you can choose “Original” or “Playlist” if the disc contains a “Playlist”.
1) In stop mode, press [POP UP MENU / MENU] to call up the DVD menu.
2) Use [Y / Z] to select “Original” or “Playlist”.
DVD-VR
CH2 LP
Original Playlist
8. CH2 LP
9. CH2 LPS
10. JAN/ 1/09 12:13AM 35-16 SP
11. JAN/ 1/09 12:15AM 35-16 SP
12. JAN/ 1/09 12:03AM 35-16 SP
13. JAN/ 1/09 12:08AM 35-16 SP
14. JAN/ 1/09 12:12AM 35-16 SP
Page Up
2/ 2
Page Down
Time Date Start
Title Info : ∗∗:∗∗:∗∗ : ∗∗/∗∗/∗∗(∗∗∗) : ∗∗:∗∗ ∗∗
3) Use [U / V] to select desired title, then press B or [ENTER].
Note
• “Original” is the title which is actually recorded on the disc.
• Playlist is edited version of the Original.
• If the disc does not contain Playlist, Playlist will not be displayed on the DVD menu.
Note
• For BD, DVD and DivX®, set “Still Mode” to “Field” in the “Video” menu if pictures in the pause mode are blurred (refer to page 32).
Resume Playback
1) During playback, press C.
• Resume message will appear on the screen.
Resume ON
Press 'PLAY' to play from here. To play from the beginning, press 'STOP' first and then 'PLAY'.
<Example: BD>
2) Press B.
In a few seconds, playback will resume from the point at which it stopped last. To cancel the resume playback and start playing back the disc from the beginning, press C again while the playback is stopped.
Note
• For MP3, Windows Media™ Audio or JPEG, playback will resume from the beginning of the current file.
• The resume information will be saved even when the power is in standby mode.
• If you open the disc tray or press C again in stop mode, the resume information will be cleared.
• Resume playback may not be available for the BD that supports Java applications (BD-J).
• In the “SD Card” mode, the resume information will be cleared when:
- the SD Memory Card is removed.
- the unit is turned to the standby mode.
18
ENGLISH
ENGLISH
Playback Playback
Introduction Connections Playback Function Setup Others
1) During playback, press h or g repeatedly to select a
2) Press B to return to normal playback.
1) During playback, press F.
2) Press g.
3) Press g repeatedly to select a desired speed.
Fast Forward / Fast Reverse Playback
BD-V
MP3
DVD-V
WMA
desired forward or reverse speed.
h Button
g Button
• For BD, DVD and AVCHD, speed changes in 5 different levels. For audio CD, DivX speed changes in 3 different levels.
• For audio CD, MP3 and Windows Media™ Audio, sound will be output at any speed of fast forward and reverse search.
DVD-VR
1
1234
234
®
, MP3 and Windows Media™ Audio,
CD
AVCHD
DivX
®
5
5
Note
• For MP3 and Windows Media™ Audio, fast forward/fast reverse search between different files are not available.
• For audio CD, fast forward/fast reverse search between different tracks are not available during the program and random playback.
•For some DivX function.
Slow Forward Playback
BD-V
• Slow motion playback will begin and sound will be muted.
• Slow forward speed changes in 3 different levels.
g Button
®
files, fast forward/fast reverse search may not
®
DVD-V
DVD-VR
AVCHD
DivX
21 3
Step by Step Playback
®
BD-V
1) During playback, press F.
2) Press B to return to normal playback.
DVD-V
• Playback will pause and sound will be muted. The disc advances frame by frame each time F is pressed.
DVD-VR
AVCHD
DivX
F
Note
• Set “Still Mode” to “Field” in the “Video” menu if pictures in the pause mode are blurred (refer to page 32).
• Only step by step forward is available.
[A-B REPEAT]
[REPEAT]
[RANDOM]
[CLEAR]
[BLU] [YEL]
[U / V / Y / Z]
[ENTER] [RETURN]
[MODE]
BC
Dialog Speed
BD-V
This function plays back approximately at 1.3 times of normal playback while keeping the sound output. This function is available only on discs recorded in the Dolby Digital format.
1) During playback, press [MODE] repeatedly until the dialog
2) Press [ENTER] or [Y / Z] to switch (x1.3), or off.
3) Press B to return to normal playback.
DVD-V
speed setting appears.
Off
“Of f” : Plays back in normal speed.
: Plays back approximately at 1.3 times of normal
“”
playback.
DVD-VR
AVCHD
Note
• Every time you press C, the setting will be turned “Off”.
• Subtitle can be viewed during this function.
• Picture adjustment, and audio language setting cannot be changed during this function.
• Virtual surround does not function during this function.
• This function may not work at some points on a disc.
• During this function, Muilti/2ch PCM will be output from HDMI output, 2ch PCM will be output from digital audio output, or 2ch analog sound will be output from analog audio out.
4) Press B to return to normal playback.
Note
• Set “Still Mode” to “Field” in the “Video” menu if pictures in the slow playback mode are blurred (refer to page 32).
• Slow reverse is not available.
19
ENGLISH
ENGLISH
Playback Playback
Repeat Playback
Available repeat function may vary depending on the discs.
1) During playback, press [REPEAT] repeatedly until desired repeat mode appears on the screen.
The following repeat modes are available.
Repeat mode Available media
Chapter repeat
The current chapter will be played back repeatedly.
Title repeat
The current title will be played back repeatedly.
Track repeat
The current track or file will be played back repeatedly.
Group repeat
The current folder will be played back repeatedly.
All repeat
All titles, tracks or files in the media will be played back repeatedly.
BD-V
DVD-V
AVCHD
BD-V
DVD-V
AVCHD
CD
WMA JPEG
DivX
DivX
®
MP3
JPEG
DVD-VR
MP3
CD
WMA JPEG
DVD-VR
DVD-VR
®
MP3
WMA
DivX
®
A-B Repeat
BD-V
DVD-V
Desired section can be played back repeatedly.
1) Press [A-B REPEAT] at the desired starting point A.
2) Press [A-B REPEAT] at the desired ending point B.
• The repeat sequence begins.
3) Press [A-B REPEAT] to exit the sequence.
DVD-VR
CD
AVCHD
DivX
®
Note
• The chapter/title/track/group repeat setting will be cleared when moving to other chapter, title, track/file or folder.
• Repeat playback does not function during A-B repeat playback.
• Repeat chapter/title is not available with some scenes.
• A-B Repeat can only be set within the current title or current track/file.
• A-B Repeat is not available with some scenes.
• To cancel the A point which was set, press [CLEAR].
• A-B Repeat playback does not function during chapter, title, track, group or all repeat playback.
•For some DivX
Program Playback
CD
You can program the disc to play back in your desired order.
1) In stop mode, press [MODE].
• The program screen will appear.
2) Use [U / V] to select a track/file, then press [ENTER].
• For MP3, Windows Media™ Audio, and JPEG, use [U / V] to select a folder, then press [ENTER] first, and then use [U / V] to select a track/file, then press [ENTER].
•Press [CLEAR] to erase the last track/file of the program.
• Select “All Clear” at the bottom of the list to erase all the tracks/files in the program.
• The programmed track/file is displayed in the right hand screen.
• If the entire program cannot be displayed on the screen, “L” or “K” appears.
•Use [Y / Z] to go back forward between the hierarchy of folders.
• If eight or more tracks/files were set in a program, use [BLU]/ [YEL] to see all the tracks/files.
®
files, A-B Repeat playback may not function.
MP3
WMA
<Example : MP3>
- / 7
Program
MP3
MP3_1 MP3_2 MP3_3 MP3_4 MP3_5 MP3_6 MP3_7
JPEG
1/ 2
Page Down
1/ 1
3) Press B to start program playback.
• Program playback will start.
Note
• During the program playback, press C once to set the resume point, and then press B to resume the program playback from where C was pressed (audio CD) or from beginning of the file where C was pressed (MP3, Windows Media™ Audio, or JPEG).
• During the program playback, press C twice to display the program screen. To go back to the normal program playback, press
[RETURN]
• Your program is still stored until either the disc tray is open or power is turned to the standby mode.
• Up to 99 tracks/files can be entered.
• To repeat the current track/file in the program, press [REPEAT] repeatedly until “ Track” appears during play back. To repeat the entire program press [REPEAT] repeatedly until “ All” appears during playback.
• Even if an inserted disc contains mixed MP3 and Windows Media™ Audio files, program function allows 99 files in combination of MP3 and Windows Media™ Audio files.
• The total number of selected tracks for the program playback will be displayed in the front panel display.
• Playback from a desired track/ file and random playback are not available during program playback.
to exit from the program screen, then press B.
PIP (Picture in Picture) (BONUSVIEW) Setting
BD-V
Some BD-Video have the PIP (picture-in-picture) function which enables you to display the secondary video in the primary video. You can call up the secondary video by pressing [MODE] repeatedly whenever the scene contains the secondary video.
primary video
secondary video
Introduction Connections Playback Function Setup Others
20
ENGLISH
ENGLISH
Playback Playback
1) During playback, press [MODE] repeatedly until the PIP
Introduction Connections Playback Function Setup Others
2) Use [U / V] to select the secondary video you want.
3) Press [RETURN] or [MODE] to remove the PIP information.
This function shuffles the play back order of tracks/files.
1) In stop mode, press [RANDOM].
2) Press B to start random playback.
setting appears.
• PIP information will appear.
• The secondary video will be displayed and the secondary audio will be output.
Note
• The secondary audio will not be output when the secondary audio is set to “Off” or when “BD Audio Mode” is set to “HD Audio Output”. Refer to “Setting the BD Audio Mode” on page 25.
Random Playback
CD
MP3
WMA
JPEG
- - / 14
CD-DA
1 3 : 40 2 5 : 38 3 3 : 06 4 4 : 38 5 3 : 28 6 3 : 12 7 5 : 09
Page Down
Total
1/ 2
Random 0 : 59 : 28
<Example: audio CD>
Note
• During the random playback, press C once to set the resume point, and then press B to resume the random playback from where C was pressed (audio CD) or from beginning of the file where C was pressed (MP3, Windows Media™ Audio, or JPEG).
• During the random playback, press C twice to display the random playback screen. To cancel the random playback, press [RANDOM] when the random playback screen is displayed.
• To repeat the current track/file in the random selection, press [REPEAT] repeatedly until “ Track” appears during
playback. To repeat the entire random selection press [REPEAT] repeatedly until “ All” appears during
playback.
• You cannot go back to the previous track/file during random playback.
• For a disc containing mixed MP3 and Windows Media™ Audio files, random playback of those files will be performed.
[the Number buttons]
[ZOOM] [CLEAR]
[ANGLE]
[SEARCH MODE]
[U / V / Y / Z]
[ENTER] [RETURN]
Zoom
®
DVD-V
DVD-VR
DivX
This function allows you to enlarge the video image and to pan through the zoomed image.
1) Press [ZOOM] during playback.
• Playback will continue.
2) Press [ZOOM] repeatedly to select a desired zoom factor: x1.2, x1.5, x2.0, x4.0 or off.
• “x4.0” zoom is not available for DivX
x4.0
3) Use [U / V / Y / Z] to move the zoomed picture across the screen.
4) Press [ZOOM] repeatedly to exit zoom mode.
JPEG
®
and JPEG.
x2.0 x1.2 x1.5
H
G
21
ENGLISH
ENGLISH
Playback Playback
Note
• For BD and AVCHD, zoom function is not available.
• Zoom function does not work while disc menu is shown.
• Navigation screen is not available on JPEG.
• You cannot pan through the zoomed picture on some JPEG files.
• For some DVD, “x4.0” zoom is not available.
•For DivX® files with small image, zoom function is not available.
•For DivX®, depending on the size of the image, some zoom factor may not be available.
•For DivX zoom position, the screen may become black for a moment. This is not a malfunction.
®
, when changing the zoom factor or moving the
Camera Angle
BD-V
Some BD and DVD contain scenes which have been shot simultaneously from various angles. You can change the camera
angle when appears on the screen.
1) Press [ANGLE] during playback.
2) Use [U / V] to select your desired angle.
DVD-V
• The selected angle will be displayed on the display bar at the top of the screen.
Note
• If the “Angle Icon” setting is “Off” in the “Others” menu, will not appear. Refer to page 37.
Search
Using H / G
1) Press G to skip to the next chapter, track or file during playback.
To go back to the previous chapter, track or file, press H twice in quick successions.
Note
• If title contains no chapters, H / G changes the title.
Using [SEARCH MODE]
By using the [SEARCH MODE], you can select following search options.
Search mode Available media
/
Title / Chapter search
BD-V
DVD-V
DVD-VR
AVCHD
Tra ck Search
Time Search
Marker Search
CD
WMA JPEG
BD-V
CD
BD-V
®
DivX
MP3
DVD-V
AVCHD
DVD-V
DVD-VR
®
DivX
DVD-VR
AVCHD
1) Select a type of search by pressing [SEARCH MODE].
• Every time you press [SEARCH MODE], type of search
changes.
2) Enter the desired chapter, track, file, title number or time to search for using [the Number buttons].
• Chapter, title, track or time search will start. e.g.
• For the disc with less than 10 titles, press the title number
directly.
• For discs with 10 or more but less than 100 titles, to play back
a single-digit title, press [0] first, then the title number (e.g. for title 3, press [0], [3]). To play back a double-digit title, press the title number.
• For discs with 100 or more titles, to play back a single or a
double-digit title, press [0] first, then the title number (e.g. for title 3, press [0], [0], [3] and for title 26, press [0], [2], [6]). To play back a triple-digit title, press the title number.
Note
• During program and random playback, search functions are
not available except the search using H / G.
• Time search function is available only in the same track, file or title.
•For some DivX
• For BD and AVCHD, chapter and time search are available only during playback.
®
files, time search may not function.
Marker search
This feature allows you to assign a specific point on a title or track to be called back later.
1) During playback, press [SEARCH MODE] repeatedly until marker setting appears.
2) Use [Y / Z] to select a marker number (1-9).
--- --:--:--
3) When the disc reaches the point you want to set a marker, press [ENTER].
• The title or track and elapsed playback time will appear on
the screen.
4) Press [SEARCH MODE] or [RETURN] to exit.
5) To return to the marker later, call the marker setting by pressing [SEARCH MODE] repeatedly during playback or in stop mode, and use [Y / Z] to choose a desired marker, then press [ENTER].
Note
• Opening the disc tray, turning the unit to the standby mode
or selecting “AC” at step 2) and pressing [ENTER] will erase all markers.
• To clear a marker, use [Y / Z] to select the marker number to be cleared and press [CLEAR].
• You can mark up to 9 points.
• For BD-Video and AVCHD, marker search between different titles is not available.
• For BD and AVCHD, you can return to the maker only during playback.
Introduction Connections Playback Function Setup Others
22
ENGLISH
ENGLISH
Playback Playback
Introduction Connections Playback Function Setup Others
[TOP MENU]
[U / V / Y / Z]
[SUBTITLE]
[DISPLAY]
[POP UP MENU / MENU]
[ENTER]
[AUDIO]
WMA
OFF (File information (elapsed time)) A File name information A Tag information (title name) A Tag information (artist name) A OFF (File information (elapsed time))
JPEG
OFF A File information A File name information A OFF
Bit rate information
9
10
AB
L1
On-Screen Display
You can check information about the current disc by pressing [DISPLAY].
To call the On-Screen Display, press [DISPLAY] during playback. Each time you press [DISPLAY], the information changes. Depending on the media, available information varies.
BD-V
OFF A Title/Chapter information A Title information (elapsed time) A Title information (remaining time) A HDMI information A OFF
DVD-V
OFF A Chapter information (elapsed time) A Chapter information (remaining time) A Title information (elapsed time) A Title information (remaining time) A Bit rate information A HDMI information A OFF
AVCHD
DVD-VR
CD
OFF (Track information (elapsed time)) A Track information (remaining time) A Disc information* (elapsed time) A Disc information* (remaining time) A OFF (Track information (elapsed time))
(* not available during the program/random playback)
®
DivX
OFF A File information (elapsed time) A File information (remaining time) A File name information A HDMI information A OFF
MP3
OFF (File information (elapsed time)) A File name information A OFF (File information (elapsed time))
Chapter information
1 43 5
2/5 0:00:00
<Title / Chapter information for BD/AVCHD>
2
AB
6
1
A Current chapter number/total number of chapters B Elapsed time/remaining time of the current chapter C Current repeat setting (Only when repeat setting is active)
(C: Chapter repeat, T: Title repeat, AB : A-B repeat)
D Indicates that the multi camera angle images are available
on the scene
E Current playback status F Current title number
2/5
Title information
7 8
0:04:00
1/10
<For VR mode DVD-RW/-R>
11
AORG
I Bit rate (the amount of video data currently being read) J Layer number (Only for 2-layered discs)
(L0: Layer 0 is played back. L1: Layer 1 is played back)
K Type of title (ORG: original, PL: playlist)
Track/File information
12 13 1514
2/5 0:00:00 SD
L Current track (file) number/total number of track (file) M Elapsed time/remaining time of the current track (file) N Indication of SD Memory Card playback O Current repeat setting (Only when repeat setting is active)
(T: Track/file repeat, G: Group repeat, A: All repeat)
T
Disc information
16 17
1/10 0:04:00
A
G Current title number/total number of titles H Elapsed time/remaining time of the current title
23
ENGLISH
P Current track number/Total number of tracks Q Elapsed time/remaining time of the current disc
ENGLISH
Playback Playback
File name information
18
MP3 MUSIC
R Media icon and File name
®
:
file
DivX
Windows Media™
:
Audio file
: MP3 file
: JPEG file
Tag information
19
TITLE
[DISPLAY]
20
ARTIST NAME
S Title name based on tag information of current Windows
Media™ Audio file
T Artist name based on tag information of current Windows
Media™ Audio file
HDMI information
21
Video Info Audio Info Max Channel
U HDMI video format V Resolution of the HDMI output image W HDMI audio format X Maximum numbers of audio channels that can be
accepted by the connected device
YCbCr / 1080i
:
Dolby Digital
:
6ch
:
22
23 24
Note
• If HDMI is not connected, “---” will be displayed for HDMI information.
Selecting the Format of Audio and Video
Selecting Audio Streams/Channels
BD-V
Some discs or SD Cards with AVCHD files contain multiple audio streams. Those are often in different audio languages or audio formats. For BD available audio varies depending on the “BD Audio Mode” setting. Refer to page 25 for more information.
1) During playback, press [AUDIO].
2) Use [U / V] to select “Primary” or “Secondary” audio to
“Primary” : Sets the audio for the main picture. “Secondary” : Sets the audio for the sub-picture. When
• In order to listen to the secondary audio, the “BD Audio Mode” must be set to “Mix Audio Output”. Refer to page 25.
3) Use [U / V] to select your desire audio stream/channel.
4) Press [AUDIO] to exit.
DVD-V
BD-V
set, then press [ENTER].
Primary
1 ENG Dolby D Multi-ch /3
Secondary
2 ENG Dolby D+ Multi-ch /3
DVD-VR
sub-picture is on, the “Secondary” audio will be output with the sub-picture.
CD
AVCHD
DivX
®
DVD-V
1) During playback, press [AUDIO].
2) Use [U / V] to select your desired audio stream/channel.
• For audio CD, you can select following options.
“Stereo” : Both right and left channels are active (stereo) “L-ch” : Only left channel is active “R-ch” : Only right channel is active
3) Press [AUDIO] to exit.
DVD-VR
1 ENG Dolby D 3/2.1ch 48k /4
CD
AVCHD
DivX
®
Note
• For VR mode DVD-RW/-R with MTS (Multi-channel Television Sound) system, you can switch between “1.Main” (main audio), “1. Sub” (sub audio), and “1.Main/Sub” (main and sub audio).
• For some BD, secondary audio will be output even when sub­picture is off.
• The sound mode cannot be changed during playback of discs not recorded in multiple sound.
• Some discs allow to change audio language setting on the disc menu. (Operation varies between discs. Refer to the manual accompanying the disc.)
•Pressing [AUDIO] may not work on some discs with multiple audio Streams/Channels (e.g. DVD which allow to change audio setting on the disc menu).
• If you choose a language that has a 3-letter-language code, the code will be displayed every time you change the Audio Language setting. If you choose any other Languages, “---” will be displayed instead (refer to page 48).
• Audio Language selection cannot be made during dialog speed (refer to page 19).
• If the disc has no audio language, “Not Available” will be displayed.
• For discs with DivX audio is displayed. Other audio will be displayed with “---”.
• For DTS-CD (5.1 music disc), “DTS” will be displayed. (Selecting audio streams or channels is not available.)
®
files, only MP3, MP2 or Dolby Digital
24
ENGLISH
Introduction Connections Playback Function Setup Others
ENGLISH
Playback Playback
Selecting Subtitle Language
Introduction Connections Playback Function Setup Others
BD-V
BD, DVD-Video, AVCHD and DivX® may have subtitles in 1 or more languages. Available subtitle languages can be found on the disc case. You can switch subtitle languages anytime during playback.
1) During playback, press [SUBTITLE].
2) Use [U / V] to select “Primary Subtitle”, “Secondary
“Primary Subtitle”: Sets the subtitle for the main picture. “Secondary Subtitle”: Sets the subtitle for the sub-picture. “Subtitle Style”: Sets style of the subtitle.
3) Use [U / V] to select your desired subtitle.
4) Press [SUBTITLE] to exit.
1) During playback, press [SUBTITLE].
2) Use [U / V] to select your desired subtitle.
3) Press [SUBTITLE] to exit.
DVD-V
ΑVCHD
BD-V
Subtitle” or “Subtitle Style”, then press [ENTER].
Primary Subtitle
Secondary Subtitle
Subtitle Style
DVD-V
1ENG /3
AVCHD
DivX
Note
• Some discs will only allow you to change the subtitle from
the disc menu. Press [TOP MENU] or [POP UP MENU / MENU] to display the disc menu.
• If 4-digit language code appears in the subtitle menu, refer to “Language Code” on page 48.
• If the disc has no subtitle language or subtitle style, “Not Available” will be displayed.
•For DivX languages.
®
, the screen only displays the number of subtitle
DivX
2 ENG/11
2 ENG/11
2/25
®
®
[U / V / Y / Z]
[PURE DIRECT]
[ENTER] [RETURN]
[MODE]
Virtual Surround
BD-V
MP3
You can enjoy stereo phonic virtual space through your existing 2-channel stereo system.
1) During playback, press [MODE] repeatedly until the virtual
2) Use [U / V] to select “1” (Natural effect), “2” (Emphasized
3) Press [RETURN] to exit.
DVD-V
WMA
surround setting appears.
Off
effect) or “Off”.
DVD-VR
CD
AVCHD
DivX
®
Note
• Select virtual surround “Off” or lower the volume if the sound is distorted.
• This function cannot be used during dialog speed (refer to page 19).
• For the virtual surround, audio signal will always be 2-channel PCM.
Pure Direct Mode
BD-V
MP3
Use this function to shut down unused circuitry to achieve high quality analog sound.
1) Press [PURE DIRECT] repeatedly to select your desired pure
DVD-V
WMA
direct mode.
• Each time you press [PURE DIRECT], the pure direct mode
changes as “Normal” A “VideoOff” A “Disp.Off” A “All Off” A “Normal”. The modes will be displayed on the front panel display.
DVD-VR
CD
AVCHD
DivX
®
Video / audio outputs for each mode
“Normal” : Normal playback mode (pure direct mode
is off).
“VideoOff” : Video signal will not be output. “Disp.Off” : Circuitry for front panel display and
indicators will be shut down.
“All Off” : Video signal will not be output and
circuitry for front panel display and indicators will be shut down.
Note
• If you turn off the unit or put this unit to standby mode, the pure direct mode will go back to “Normal”.
[PURE DIRECT] is not available when the setup menu is displayed.
Setting the BD Audio Mode
BD-V
BD audio mode is to choose between two ways; you could output the secondary and interactive audio accompanied by the primary audio or you could output the primary audio only. Depending on the setting of the mode, Dolby Digital, DTS, Dolby Digital Plus, Dolby TrueHD, or DTS-HD output changes between Multi PCM and bitstream.
1) In stop mode with BD inserted, press [MODE].
2) Use [U / V] to select desired setting.
“Mix Audio Output”
If it is available, BD-Video’s secondary and interactive audio will be output with the primary audio.
• The secondary audio is the audio for the sub picture (Director’s comment etc.) and the interactive audio is the audio for the interactive application (Button click sounds etc.).
“HD Audio Output”
Only the primary audio will be output. Set this mode in order to output Dolby Digital, Dolby Digital Plus, Dolby TrueHD, DTS or DTS-HD sound of BD through HDMI connection.
3) Press [RETURN] to exit.
• You can also set “BD Audio Mode” from the setup menu. Refer to page 33.
Note
• Refer to pages 13 - 14 for more information of audio settings.
25
ENGLISH
ENGLISH
Playback Playback
Adjusting the Picture
®
BD-V
You can adjust the picture quality and store the setting you have adjusted on memory 1-5.
1) During playback, press [MODE] repeatedly until the picture
2) Use [U / V] to select a memory from “Memory 1” to
3) Use [U / V] to select an item to be adjusted, then use
Contrast
Brightness
Sharpness
Gamma Correction
Color
Black Level *
*1 Not effective for the video signal of COMPONENT VIDEO OUT
DVD-V
adjustment menu appears.
• Picture adjustment menu:
“Memory 5” to store your setting, then press [ENTER].
[Y / Z] to adjust the setting.
Item Description
(480p/720p/1080i) and HDMI OUT jacks.
DVD-VR
Memory 1
2.Brightness 0
1.Contrast
6.Black Level
Adjusts the difference between the bright and dark parts of the picture.
Adjusts the brightness of the picture.
Adjusts the sharpness of the picture.
Changes the amount of gamma correction to adjust overall brightness of a picture. Make dark/ bright section easier to see.
Adjusts the balance between green and red.
1
Adjusts the black level.
AVCHD
DivX
0
7.5 IRE
Adjustment range
(* : Default setting)
-7 to +7 (0*)
0 to +15 (0*)
-6 to +6 (0*)
0 to +5 (0*)
-7 to +7 (0*)
0 IRE or 7.5 IRE (7.5 IRE*)
Item Description
Noise Reduction (Not available for BD/AVCHD)
Reduces the noise of the playback picture.
Adjustment range
(* : Default setting)
Off* +1: Execute MPEG
noise reduction which reduce the block noise and mosquito noise on the subtitle on movie.
+2: Execute 3D noise reduction which detect and delete the noise by comparing each picture frames.
+3: Execute both MPEG noise reduction and 3D noise reduction.
[BLU] [YEL]
[U / V / Y / Z]
[ENTER]
B
Playing Back an Audio CD or a Disc with DivX®/MP3/ Windows Media™ Audio/JPEG File
®
CD
1 2
DivX
Insert a disc with DivX®, MP3, Windows Media™ Audio, JPEG files.
• The file list will appear on the screen.
Use [U / V] to select a desired folder, file or title, then press [ENTER]. Use [Y / Z] to go back and forward between the hierarchies.
•If you press B or [ENTER] on the files, playback will
start.
MP3
1
6
A Track/ file information B Playback status C Current disc or folder name will be displayed.
(For audio CD, “CD-DA” will be displayed.)
D List of the file/ folder names in the current folder/disc E Current page/ total page number F Operation guide
Icons:
:Folders
®
:
DivX
files
: MP3 files
: Windows Media™ Audio files
: JPEG files
It is recommended that files to be played back in this unit are recorded under the following specifications:
Page Up Page Down Media Mode
-- / 28
File List
MP3_1 MP3_2 MP3_3 MP3_4 MP3_5 MP3_6 MP3_7
ABC
WMA
JPEG
2 / 3
2 3
4
5
Introduction Connections Playback Function Setup Others
26
ENGLISH
ENGLISH
Playback Playback
<DivX®>
Introduction Connections Playback Function Setup Others
Official DivX® Certified product
• Playable codec of AVI files :
®
DivX
3.x, DivX®4.x, DivX®5.x,
®
DivX
6.x
• Maximum size of image : 1920 x 1080 @30 fps 1280 x 720 @60 fps
• Sampling frequency of audio : 16 kHz - 48 kHz
• Audio type : MPEG1 audio layer 3 (MP3), MPEG1 audio layer 2, Dolby Digital
<MP3 / Windows Media™ Audio>
• Sampling frequency : 44.1 kHz or 48 kHz
• Constant bit rate : 112 kbps - 320 kbps (MP3), 48 kbps - 192 kbps (Windows Media™ Audio)
<JPEG>
• Upper limit : 2,560 x 1,900 dots (sub sampling is 4:4:4)
5,120 x 3,840 dots (sub sampling is up to 4:2:2)
• Lower limit : 32 x 32 dots
• File size of image maximum : 12 MB
To Play Back the DivX® Subtitle Created by the User.
The subtitle created by the user can be displayed during DivX® playback.
1) After selecting the DivX file you want to playback, then press [BLU]. Subtitle list will appear.
• If there is more than one extension, the extension selection
appears in the subtitle list.
2) Use [U / V] to select the desired extension of the subtitle file you want to display, then press [ENTER].
• If you insert a BD-RE/-R, DVD-RW/-R, CD-RW/-R with DivX that are mixed with MP3/Windows Media™ Audio/JPEG files, the
File List
®
file, use [U / V] to select the
- - / 11
Subtitle List
55
[ Off ] [ SMI ] [ SRT ] [ SUB ]
®
files
Hint for the purchased or rental official DivX product
• When you purchased or rented a DivX site of DivX® video which is called DivX® Video-On-Demand (VOD) services, a registration code is required every time you get the new file from the DivX
®
VOD services. Refer to “DivX(R) VOD”
on page 38.
• Some DivX®VOD files are restricted with the limited playable times (you cannot play them back beyond the limit). If
your DivX
®
VOD file has such limit, the playback confirmation screen will appear.
•Use [Y / Z] to select “Yes” if you want to play back the file, or to select “No” if you do not wish to play it back. Then, press [ENTER] to confirm the selection.
• You cannot play back the DivX®VOD files, of which rental
period has been expired. In such case, press [ENTER] and select other files that can be played back.
®
Certified
®
file through the official
DivX(R) VOD Rental
This rental has views left. Do you want to use one of your views now?
Yes
Rental Expired
This rental is expired. Please push ‘ENTER’.
playback media selection screen will be displayed. Use [U / V]
Note
• The system can recognize up to 255 folders/999 files for CD, 999 folders/9999 files for BD, DVD and SD Memory Card.
• The name of folder and file can be displayed up to 28 characters. Unrecognizable characters will be replaced with asterisks.
• The 9th and deeper hierarchies cannot be displayed for CD and the 10th and deeper hierarchies cannot be displayed for BD, DVD and SD Memory Card.
• Files whose extension is other than “.avi/ .divx (DivX (MP3)”, “.wma (Windows Media™ Audio)” or “.jpg / .jpeg (JPEG)” will not be listed.
• Some unplayable folders or files may be listed due to the recording status.
• High-resolution JPEG files take longer to be displayed.
• Progressive JPEG files (JPEG files saved in progressive format) cannot be played back on this unit.
• This unit recognize up to 8 characters of file name in the SD Memory Card. Characters after 8th will not be displayed.
• If a disc contains AVCHD files, the playback of other files which are in the same disc is not available.
• File list cannot be called up during playback of DivX
®
)”, “.mp3
®
or JPEG
to select your desired media to play back then press [ENTER].
Please select the media to play back.
Video Audio Picture
•Press [YEL] to call up the playback media selection screen in stop
mode.
• You cannot play back the
®
DivX
VOD files obtained with
different registration codes on this unit. Press [ENTER] and select other files that can be played back.
• You cannot playback the DivX® file that has the resolution which this unit does not support. This
unit does not support the DivX
®
files that have the image size that exceeds 1920 x 1080 @30 fps or 1280 x 720 @60 fps.
•For DivX® files with audio format other than MPEG1 audio layer 3 (MP3), MPEG1 audio layer 2 and Dolby Digital, audio will not be output and only the video will be output.
This player is not authorized to play this video. Please push ‘ENTER’.
This player does not support this video format. Please push ‘ENTER’.
This player does not support this audio format. Please push ‘ENTER’.
Authorization Error
Resolution Error
Audio Format Error
files.
No
27
ENGLISH
ENGLISH
Playback Playback
What is DivX®?
•DivX® is a codec (compression/decompression) that can compress images to a very small amount of data. The software can compress video data from almost any devices to the size that can be sent on the Internet without compromising visual quality of the images.
• A file with an extension of “.avi” and “.divx” is called an DivX® file. All files with the DivX
• For more information for DivX®, please visit http://www.divx.com
Note for DivX
• Even if the file has an extension of either “.avi” and “.divx”, this unit cannot play it back if it is recorded in the format other than DivX
• It may take a while for audio and images to be output after you inserted a disc and pressed B.
• When playing back the files recorded in high bit rates, the images can be interrupted in some occasions.
• Although DivX not be able to play back some data, depending on the characteristics, bit rates, or audio format settings, etc.
•A DivX® file whose file size exceeds 32 GB cannot be played back.
• If a large-sized DivX® file is selected, it may take awhile to start the playback (over 20 seconds sometimes).
• If you try to playback the DivX resolution which this unit does not support, the playback will be stopped and error message will appear.
• Some DivX the configuration and characteristics of the disc, or due to the condition of recording and authoring software.
•If DivX® files written on a CD-RW/-R or DVD-RW/-R cannot be played back, rewrite them on a BD-RE/-R and try to play back.
®
®
.
®
logo has been obtained for this unit, it may
®
files cannot be played back on this unit due to
®
extension are recognized as MPEG4.
.
®
file that has the screen
Note for DivX® Subtitle
• To utilize this function, the following conditions must meet.
- Playback file and the subtitle file must have the same name.
- Playback file and the subtitle file must locate in the same folder.
- Only the subtitle files with the following extensions are supported; .smi (.SMI), .srt (.SRT), .sub (.SUB), .ass (.ASS), .ssa (.SSA), .txt (.TXT). (.sub (.SUB) and .txt (.TXT) files may not be recognized.)
- The subtitles that exceeds the playback time of the DivX will not be displayed.
®
file
[U / V / Y / Z]
[SETUP]
[ANGLE]
C
[ENTER] [RETURN]
[MODE]
B
Kodak Picture CD
This unit can also run JPEG files stored on Kodak Picture CD. You can enjoy picture images on the display device set by playing back the Picture CD. This unit confirms to ver.7.0 of Kodak Picture CD. For details of Kodak Picture CD, contact a shop that provides developing service of Kodak Inc.
When Kodak Picture CD is inserted in this unit, Kodak Picture CD menu appear automatically on the screen.
1
1
4
A File information B Playback status C Operation guide D Current page/ total page number
Use [U / V / Y / Z] to select a desired track to be played back, then press B or [ENTER].
2
• An image will be played back from the selected track and go to the next one in turn.
Press C to stop playback.
- - / 32
Thumbnail
Pictures
Picture 1 Picture 2 Picture 3
Picture 5
2 /6
Picture 6Picture 4
Page NextPage Prev
2
3
3
Tips for JPEG/Kodak Picture Playback
• Every press on [ANGLE] will turn the image clockwise by 90
degrees when an image is displayed.
• To change the visual effect for switching the playback image,
press [MODE] once, then use [Y / Z] or [ENTER] to switch between “Cut In/Out” and “Fade In/Out”. The size change may have no effect on some files (e.g. files with a small picture size).
• To change the size of the playback image, during the JPEG/
Kodak Picture playback. Press [MODE] twice, then use [Y / Z] or [ENTER] to switch between “Normal” (100%) and “Small” (93%). The size change may have no effect on some files (e.g. files with a small picture size).
Reading the SD Memory Card
AVCHD
You can play back the AVCHD, MP3, Windows Media™ Audio and JPEG files in an SD Memory Card. With the SD Memory Card, you can also enjoy the special additional contents for BD-ROM Profile
1.1 which can be downloaded from the Internet. You can store the contents on an SD Memory Card via computer and play them back with the BD-Video. For more information about the special additional contents, please refer to the instruction book that came with the disc.
MP3
WMA
JPEG
Inserting the SD Memory Card and playback
Insert an SD Memory Card, with the label side
1
2
facing up, into the SD card slot until it clicks.
If no disc is in operation, “Media Select” screen will appear on the TV screen.
SD Memory Card
Use [U / V] to select “SD Card”, then press [ENTER].
The file list will appear.
Introduction Connections Playback Function Setup Others
28
ENGLISH
ENGLISH
Playback Playback
Introduction Connections Playback Function Setup Others
Setting the media
If the “Media Select” screen disappears before you make the selection, follow the following procedure to select the media to playback.
3
1 2 3 4
5
Follow the step 2 in “Playing Back an Audio CD or a Disc with DivX®/MP3/Windows Media™ Audio/ JPEG File” on page 26.
Press [SETUP] in stop mode.
Use [Y / Z] to select , then press [ENTER].
Use [U / V] to select “Media Select”.
Press [ENTER] repeatedly to select “SD Card”.
Quick
Media Select SD Card BD Audio Mode Mix Audio Output HDMI Audio Out HDMI Multi(Normal) HDMI Video Resolution Auto Component Output 480i OSD Language English
• This will set the unit to “SD Card” mode. To play back the contents in any discs, exit “SD Card” mode by selecting “Disc”.
Press [SETUP] to exit.
Removing the SD Memory Card
In stop mode, push the SD Memory Card and then
1 2
slowly remove your finger.
Grasp the card and pull it out from the SD card slot.
This will set the unit to “Disc” mode.
Compatible Cards:
- SD Memory Card (8MB - 2GB)
- SDHC Memory Card (4GB - 8GB)
- miniSD Card (8MB - 2GB)
- microSD Card (8MB - 2GB)
• For miniSD Card and microSD Card, adapter will be required.
Note
• The “Media Select” screen will disappear under the conditions listed below:
- when the screen saver is activated.
- when [RETURN] is pressed.
- when the setup menu is called up.
• Do not remove the card during its playback.
• This unit supports SD Memory Card with FAT12/FAT16 file system, and SDHC Memory Card with FAT32 file system.
• Do not delete the folders or files in the SD Memory Card with your computer. This unit might not read the SD Memory Card.
• This unit recognizes up to 8 characters of file name in the SD Memory Card. Characters after 8th will not be displayed.
• If a folder or file name includes one of the following unrecognizable characters, the folder or file name may not be displayed correctly.
- Unrecognizable characters :
• Even if you turn the unit to the standby mode in “SD Card” mode, it will be in “Disc” mode the next time you turn it on.
. , " = + [ ] ; / \ : | ¥
Enjoying BD-Live Discs with Internet
BD-V
You can enjoy the BD-Live functions which enable you to use the interactive functions when the unit is connected to the Internet. (For the Network connection, refer to page 39.)
Examples for BD-Live interactive functions :
- Download the additional contents such as the movie’s trailer, subtitles and BD-J, etc.
- While downloading, special video data may be played back.
• Service and functions differ depending on the disc.
• F ol l o w t h e i n st r uc t io n s g i ve n by t h e d i sc w he n us i ng t he BD-Live function.
• You must insert an SD Memory Card when using the BD-Live function. (SD Memory Card of 1GB is recommended.)
• Do not remove the SD Memory Card when using the BD-Live function.
Note
• You must connect the unit to the Internet and set up
necessary settings in order to use the BD-Live function.
• For certain discs, setting for “BD-Live Setting” may need to be
changed.
• Depending on your connection environment, it may take
time to connect to the Internet or the Internet may not be connected.
• When BD-Live functions are used and the unit is connected to
the Internet, you may be charged for this communication.
Note for AACS Online
• The player or disc IDs may be sent to the content provider
when playing back a disc with BD-Live function.
• If you save your viewing history on the server by using these
IDs, you will be introduced to other similar movies.
• You can save game score histories.
29
ENGLISH
ENGLISH
Function Setup
[the Number buttons]
[CLEAR]
[RED / GRN / BLU / YEL]
[U / V / Y / Z]
[SETUP]
Using the Setup Menu
In the setup menu, you can change the setting for audio, video, language, etc. You cannot change the setting during playback.
Quick
Quick setting menu contains setting items extracted from custom setting menu which may be used frequently.
[ENTER]
[RETURN]
B
Use [U / V] to select setting items.
3
Follow the procedure below depending on the
4
setting items. For setting item A : Press [ENTER] repeatedly to change options. For setting item B :
1)Press [ENTER].
2)Use [U / V] to select options, then press [ENTER].
•Use [Y] or [RETURN] to go back to the previous
screen.
Press [SETUP] to exit.
5
Custom
Custom menu contains all the setting items.
Press [SETUP] in stop mode.
1
5
6
Introduction Connections Playback Function Setup Others
Follow the procedure below depending on the setting items.
For setting item A : Press [ENTER] repeatedly to change options. For setting item B :
1) Press [ENTER].
2) Use [U / V] to select options, then press [ENTER].
•Use [Y] or [RETURN] to go back to the previous
screen.
Press [SETUP] to exit.
1 2
Press [SETUP] in stop mode.
Use [Y / Z] to select , then press [ENTER].
Quick
Media Select Disc BD Audio Mode Mix Audio Output HDMI Audio Out HDMI Multi(Normal) HDMI Video Resolution Auto Component Output 480i OSD Language English
2 3
4
Use [Y / Z] to select , then press [ENTER].
Use [Y / Z] to select your desired setting category, then press [ENTER].
: Language : Video : Audio : Ratings : Others
• For “Ratings”, follow the procedure on page 36.
Use [U / V] to select setting items.
• The setting items which are not available with current situation of this unit will be displayed in gray and you cannot select the items.
30
ENGLISH
ENGLISH
Function Setup Function Setup
Language
Introduction Connections Playback Function Setup Others
Video
Language
Dialog Subtitle Disc Menu OSD Language DivX Subtitle
Original Off English English English
• For how to select the setting items and options, refer to “Custom” on page 30.
Setting items Options
Dialog
Sets the language for audio.
Original*/English/French/Spanish/German/Italian/ Swedish/Dutch/Russian/Chinese/Japanese/Korean/ Danish/Finnish/Norwegian/Icelandic/Hungarian/ Romanian/Turkish/Greek/Irish/Portuguese/Polish/ Czech/Slovak/Bulgarian/Other
Subtitle
Sets the language for subtitle.
Off*/English/French/Spanish/German/Italian/Swedish/ Dutch/Russian/Chinese/Japanese/Korean/Danish/ Finnish/Norwegian/Icelandic/Hungarian/Romanian/ Turkish/Greek/Irish/Portuguese/Polish/Czech/Slovak/ Bulgarian/Other
Disc Menu
Sets the language for disc menu.
English*/French/Spanish/German/Italian/Swedish/ Dutch/Russian/Chinese/Japanese/Korean/Danish/ Finnish/Norwegian/Icelandic/Hungarian/Romanian/ Turkish/Greek/Irish/Portuguese/Polish/Czech/Slovak/ Bulgarian/Other
OSD Language
Auto/English*/Français/Español
Sets the language for OSD (on-screen display).
DivX Subtitle English*/French/Spanish
Sets the language for DivX
®
Subtitle.
• Settings with (*) are the default.
• Quick menu consists of the setting menus frequently used, and they are accompanied with mark.
• If you select “Other”, enter the 4-digit number code for the desired language (refer to “Language Code” on page 48). Only the languages supported by the disc can be selected.
Video
TV Aspect HDMI Select HDMI RGB Setting HDMI Auto Format HDMI Video Resolution HDMI Deep Color Component Output
16:9 Wide YCbCr Normal Max Auto Auto 480i
Video
Progressive Mode Still Mode Wall Paper
Auto Auto Picture
• For how to select the setting items and options, refer to “Custom” on page 30.
Setting items Options
TV Aspect
Sets a picture size according to aspect ratio of the connected display device.
16:9 Wide*: Select this when a wide-screen TV is connected. Disc recorded in wide screen format is played over the entire screen.
4:3 Pan & Scan: Select this to play back the disc recorded in wide screen format with 4:3 TV in the pan & scan mode (with the
sides of the picture cut off). Discs which pan & scan is not specified are played in the letter box mode.
4:3 Letter Box: Select this to play back the disc recorded in wide screen format with 4:3 TV in the letter box mode. (with black strips at the top and bottom).
4:3 Squeeze Auto: When playing 4:3 images, the picture is displayed in the center of the 16:9 screen with a 4:3 aspect ratio.
4:3 Squeeze On: The picture is displayed in the center of the 16:9 TV screen with a 4:3 aspect ratio, regardless of the original
image size.
HDMI Select
Select an HDMI output mode between “YCbCr” and “RGB”.
YCbCr*: Component format video signals and audio signals are
output from the HDMI OUT.
RGB: RGB format video signals and audio signals are output
from the HDMI OUT.
Remote control operation
buttons
:
Displaying the menu Cancel the menu
:
Move the cursor (Up/Down/Left/Right)
31
ENGLISH
: Confirm the setting : Return to previous menu
ENGLISH
Function Setup Function Setup
Setting items Options
HDMI RGB Setting
Sets the digital RGB image range (data range) output from the HDMI OUT.
HDMI Auto Format
Makes the setting of the “Auto” for “HDMI Video Resolution”.
HDMI Video Resolution
Sets the HDMI video resolution.
HDMI Deep Color
Sets whether output the picture from HDMI with the Deep Color or not.
Component Output
Sets the video resolution for component output.
Normal*: Output as “16 (black)” to “235 (white)”.
Enhanced: Output as “0 (black)” to “255 (white)”. Depending on the display device you are using, the black colors may seem to stand out when using HDMI connections. If so, set to “Enhanced”.
Max*: The maximum resolution that can be input to the connected HDMI device is detected and the HDMI
output resolution is selected automatically. Panel: The number of pixels of the connected HDMI device’s
panel is detected and the HDMI output resolution is selected automatically.
Auto*: HDMI video resolution will be selected automatically depending on the connected HDMI device and setting of the “HDMI Auto Format”.
Source Direct: HDMI video resolution will be set to the recorded resolution of a playback media.
480i 480p 720p 1080i 1080p 1080p24:
Gives a natural and high quality film reproduction of 24­frame film material. The connected display device has to be compatible with 1080p24 frame input.
Auto*: The picture through the HDMI will be output with Deep
Color if the connecting device supports Deep Color. Off: The picture through the HDMI will be output without
Deep Color. 480i* 480p 720p 1080i
Progressive Mode
Sets the optimum progressive mode for the image material output from HDMI OUT jack and COMPONENT VIDEO OUT jacks.
Still Mode
Adjusts picture resolution and quality in still mode.
Setting items Options
Auto*: The progressive mode will detect 24-frame film material
(movies) and automatically select appropriate progressive mode.
Video: Suited for playing video material discs (TV shows or animation).
Auto*: Automatically selects the best resolution setting (“Frame” or “Field”) based on the data characteristics of the pictures.
Field: Stabilizes the pictures, although the picture quality may become coarse due to the limited amount of data.
Select “Field” when the pictures are still unstable even if “Auto” is selected.
Frame: Displays relatively motionless pictures in higher resolution. “Frame” improves the picture quality, although it may unstabilize the pictures due to alternate
output of 2-field data.
Introduction Connections Playback Function Setup Others
Remote control operation
buttons
:
Displaying the menu Cancel the menu
:
Move the cursor (Up/Down/Left/Right)
32
ENGLISH
: Confirm the setting : Return to previous menu
ENGLISH
Function Setup Function Setup
Introduction Connections Playback Function Setup Others
Setting items Options
Wall Paper
Sets the picture to be displayed on the screen for stop mode or audio playback mode.
Picture* Blue Black Gray
• Settings with (*) are the default.
• Quick menu consists of the setting menus frequently used, and they are accompanied with mark.
• For “HDMI RGB Setting”, select “Enhanced” if the black-white contrast is not clear. The setting is effective only for HDMI RGB output.
• Even if “HDMI Video Resolution” is set to “1080p24”, for the BD that is not recorded by 1080p24 frame or for DVD, a video resolution supported by the disc and the display device will be output instead of 1080p24 frame.
• An individual picture on the screen is called as “Frame” , which consists of two separate images called as “Field”. Some pictures may be blurred at the auto setting in “Still Mode” due to their data characteristics.
• If the picture is not output properly to the display device because of the “HDMI Video Resolution” or “Component Output” setting, press and hold B on the front panel for more than 5 seconds. Both settings will be reset to the default automatically.
• If “Component Output” is set to “480i”/“480p”, “4:3 Squeeze Auto” and “4:3 Squeeze On” in “TV Aspect” are not available.
• If HDMI is connected, for video resolution for the component output, you can only select video resolution that currently output from HDMI OUT or 480i.
• If the video resolution for the component output and HDMI video resolution does not match, the video resolution for the component output will be switched to current HDMI output resolution. COMPONENT VIDEO OUT jacks may not output any signals depend on the disc material.
• If you play back copy-protected DVD-Video, 480p signal will be output from the COMPONENT VIDEO OUT jacks, when “Component Output” is set to “720p” or “1080i”.
• The setting items which are not available with current situation of this unit will be displayed in gray and you cannot select the items.
• Even if “HDMI Select” is set to “YCbCr”, if the display device does not support YCbCr, RGB will be output.
• If “HDMI Video Resolution” is set to “Source Direct”, “1080p” or “1080p24”, you cannot set “Component Output”.
Audio
Audio
BD Audio Mode HDMI Audio Out Down Sampling DRC
• For how to select the setting items and options, refer to “Custom” on page 30.
Setting items Options
BD Audio Mode
For BD, select whether to output the secondary and interactive audio with primary audio if it is available or only the primary audio. Refer to “Setting the BD Audio Mode” on page 25.
HDMI Audio Out
Sets the audio format for the audio output from the HDMI OUT.
Mix Audio Output HDMI Multi(Normal) Off Auto
Mix Audio Output*: Output the secondary and interactive audio with
primary audio if it is available.
HD Audio Output: Output only the primary audio. Set this mode in order to
output Dolby Digital, Dolby Digital Plus, Dolby TrueHD, DTS or DTS-HD sound of BD through HDMI connection.
HDMI Multi(Normal)*: The multi-channel audio signals are output from the HDMI OUT with a bitstream or PCM.
HDMI Multi(LPCM): The multi-channel audio signals are output from the HDMI OUT with a PCM.
• Refer to pages 34-36 for speaker setting options. HDMI 2ch:
The audio signals are output from the HDMI OUT with a downmixed to 2ch PCM.
Remote control operation
buttons
:
Displaying the menu Cancel the menu
• The default setting of the “BD Audio Mode” is “Mix Audio Output”. If you want to output only the high quality primary audio, set “BD Audio Mode” to “HD Audio Output”.
:
Move the cursor (Up/Down/Left/Right)
33
ENGLISH
Audio Mute: Mutes the HDMI audio signal, and set the signal format of the DIGITAL OUT.
• Refer to the “Digital Out Setting” on page 34 for setting options.
: Confirm the setting : Return to previous menu
ENGLISH
Function Setup Function Setup
Setting items Options
Down Sampling
Sets the digital audio output when playing BD or DVD recorded in PCM.
DRC
Sets whether to compress the range of sound volume (Dynamic Range Control) when Dolby Digital, Dolby Digital Plus or Dolby TrueHD audio is played back.
• Settings with (*) are the default.
• Quick menu consists of the setting menus frequently used, and they are accompanied with mark.
• Under following circumstances, “HDMI Multi(Normal)”, “HDMI Multi(LPCM)” and “HDMI 2ch” is not available.
- HDMI cable is not connected to HDMI OUT jack.
- Connected display device is off.
- Connected display device is not compatible with audio output.
On: PCM signals are converted to 48 kHz for output.
• Set to “On” when using digital connections to an AV amplifier that is not compatible with sampling frequencies of 96 kHz.
Off*: For BD or DVD recorded in PCM without copyright protection, 2-channel audio signals up to 192 kHz are
output as PCM signals with no conversion. Auto*:
When the discs that are recorded in the Dolby TrueHD format is in playback, this unit detects DRC setting of the disc and set the DRC setting of this unit to “On” or “Off” automatically.
Off
On
Bitstream*: When playing back discs recorded in Dolby Digital, Dolby Digital Plus, Dolby TrueHD, DTS or DTS-HD, the corresponding core stream (Dolby Digital or DTS) are output.
LPCM: Full decoded 2ch PCM signal will be output from DIGITAL OUT.
• This setting is not effective when the HDMI audio signal is output.
• When both HDMI and DIGITAL OUT is connected to other devices, the audio signals currently output from the HDMI OUT will be output from the DIGITAL OUT jack as well, except that HDMI 2ch signal will be output from HDMI OUT jack, when connected device does not support Dolby Digital and DTS.
• When “BD Audio Mode” is set to “Mix Audio Output”, the audio output from DIGITAL OUT will follow the setting in the “HDMI Audio Out”. (When outputting Multi PCM from HDMI OUT, 2ch Downmix PCM will be output from DIGITAL OUT.)
• Refer to pages 13 - 14 for more information of audio settings.
Speaker Setting
This unit allows you to enjoy multi-channel surround sound such as 7.1-channel / 5.1-channel surround. <Example of basic layout with 7.1ch surround system>
Front speaker (left)
Center speaker
Front speaker (right)
Introduction Connections Playback Function Setup Others
Digital Out Setting
When the “Audio Mute” is selected in “HDMI Audio Out” setting, audio signal of the HDMI is muted and the audio signals output from DIGITAL OUT changes depending on the “Digital Out” setting.
<“Digital Out” setting> Audio A HDMI Audio Out A Audio Mute
Remote control operation
buttons
:
Displaying the menu Cancel the menu
:
Move the cursor (Up/Down/Left/Right)
Subwoofer
Surround speaker (left) Surround speaker (right)
Surround back speaker (left) Surround back speaker (right)
: Confirm the setting : Return to previous menu
34
ENGLISH
ENGLISH
Function Setup Function Setup
To make the most of its feature, set up your speakers appropriately by referring to the table below.
Introduction Connections Playback Function Setup Others
Speaker setting options are available in SETUP A Quick A HDMI Audio Out A HDMI Multi(LPCM) or SETUP A Custom A Audio A HDMI Audio Out A HDMI Multi(LPCM)
How to navigate through the “HDMI Multi(LPCM)” setting
1) Use [U / V] to select the menu item.
2) Use [U / V] to select setting items.
3) Use [Y / Z] to select desired options.(Except for “Test Tone” and “Default”.)
4) Press [SETUP] to exit.
•Use [RETURN] to go back to the previous screen.
For “Test Tone”:
Use [Y / Z] to select “Manual” or “Auto”, then press [ENTER].
• The test tone will be output. If you select “Manual”, use [U / V] to select desired speaker, then use [Y / Z] to adjust the volume. If you select “Auto”, use [Y / Z] to adjust the volume of the speaker
that output the test tone.
• If you want to stop the test tone, press [RETURN].
For “Default”:
Press [ENTER] to reset the “Speaker Configuration”, “Channel Level” or “Delay Time” setting to the default.
Menu Setting items Options Descriptions
Speaker Configuration
Select the desired speaker to set. Then change the setting appropriately by referring to the descriptions.
Front Large* Large:
Small
Center Large*
Small
Subwoofer On*
Surround Large*
Small
Surround Back Large*
Small
Default Select “Default”, then
For the large speakers with strong low frequency reproduction capabilities. Small: For the small speakers which do not provide strong bass sound. You cannot change the setting of “Subwoofer”. If connected device is not compatible with subwoofer, “Subwoofer” will be displayed in gray.
press [ENTER] to reset the “Speaker Configuration” setting to the default.
• For “Speaker Configuration” setting, the settings of each speaker size may be adjusted automatically corresponding to each setting. (e.g. If “Front” is set to “Small”, you cannot set “Center”, “Surround” and “Surround Back” to “Large”.)
Menu Setting items Options Descriptions
Channel Level
Tests or sets the volume for each speaker.
Test Tone: “Test Tone” is the test tone which can be
output from the speakers so that you can adjust the volume for each speaker.
Front Lch 0 dB to -12 dB
Center 0 dB to -12 dB
Front Rch 0 dB to -12 dB
Surround Rch 0 dB to -12 dB
Surround Back Rch 0 dB to -12 dB
Surround Back Lch 0 dB to -12 dB
Surround Lch 0 dB to -12 dB
Subwoofer 0 dB to -12 dB
Default Select “Default”, then
Off* Select “Off” to deactivate
Manual
Auto
(0 dB*)
(0 dB*)
(0 dB*)
(0 dB*)
(0 dB*)
(0 dB*)
(0 dB*)
(0 dB*)
the “Test Tone” feature. Select “Manual”, then
press [ENTER] to manually set the volume for the desired speaker. Select “Auto”,then press [ENTER] to automatically output the test tone from each speaker.
If you have selected “Manual” in “Test Tone”, select the desired speaker to set and adjust the volume for the selected speaker.
If you have selected “Auto” in “Test Tone”, test tone will be output automatically in order. Adjust the volume of the speaker that output the test tone.
press [ENTER] to reset the “Channel Level” setting to the default.
Remote control operation
buttons
:
Displaying the menu Cancel the menu
:
Move the cursor (Up/Down/Left/Right)
35
ENGLISH
: Confirm the setting : Return to previous menu
ENGLISH
Function Setup Function Setup
Menu Setting items Options Descriptions
Delay Time
This is a parameter for optimizing the timing at which the sound is output from the speakers according to their distance from the listening position.
Distance Feet* Set the desired measure
system. This measure system will be used for “Delay Time”
Meters
setting. Press [ENTER] to switch the setting.
Front 0ft to 60ft (12ft*)
(0m to 18m (3.6m*))
Center 0ft to 60ft (12ft*)
Select the distance from the listening point to the speaker to get the ideal delay time.
(0m to 18m (3.6m*))
Surround 0ft to 60ft (10ft*)
(0m to 18m (3.0m*))
Surround Back 0ft to 60ft (10ft*)
(0m to 18m (3.0m*))
Default Select “Default”, then press
[ENTER], to reset the “Delay Time” setting to the default.
• Settings with (*) are the default.
• For “Delay Time”, the difference between the value of the “Front”, “Surround” and “Surround Back” setting cannot exceed 15 ft (4.5m), and the difference between the value of the “Front” and “Center” setting cannot exceed 5 ft (1.5m).
• For “Delay Time”, the value of the “Center”, “Surround” and “Surround Back” setting cannot exceed the value of the “Front” setting.
• For “Delay Time”, the setting of “Center”, “Surround” and “Surround Back” will be changed automatically to the setting value of the “Front”. (e.g. If the “Front” is set to 60ft (18m), the setting of “Center”, “Surround” and “Surround Back” will be changed to 60ft (18m) as well.)
• If you want to stop the test tone, press [RETURN].
Ratings
Ratings control allows you to set a limit, which prevents your children from viewing inappropriate materials. Playback will stop if the ratings exceed the levels you set, and it will require you to enter a password before the disc will play back.
Ratings
BD Rating Level DVD Rating Level Password Change
All All
1) Use [Y / Z] to select , then press [ENTER].
2) Press [the Number buttons] to enter your 4-digit password. For the first time use: Press [the Number buttons] to enter any 4-digit number (except for 4737),
then press [ENTER]. That number will be used as the password from the second time. Record your password in case you forget it.
• If you forgot the password, enter [4], [7], [3], [7]. The password will be cleared and rating level
will be set to “All”.
• While you input the password, press [CLEAR] to clear the number, then re-enter the password.
Proceed to A – C
A) BD Rating Level
1) Use [U / V] to select “BD Rating Level”, then press [ENTER].
2) Use [U / V] to select your desired option, then press [ENTER].
“All” : To release the limitation. “Age Setting”: To set the age limitation.
• After selecting “Age Setting”, use [the Number buttons] to enter the age from 0 – 254. (e.g. for age 15, press [0],[1],[5])
3) Press [SETUP] to exit.
Introduction Connections Playback Function Setup Others
Remote control operation
buttons
:
Displaying the menu Cancel the menu
B) DVD Rating Level
1) Use [U / V] to select “DVD Rating Level”, then press [ENTER].
2) Use [U / V] to select a desired level, then press [ENTER].
3) Press [SETUP] to exit.
:
Move the cursor (Up/Down/Left/Right)
36
ENGLISH
: Confirm the setting : Return to previous menu
ENGLISH
Function Setup Function Setup
Introduction Connections Playback Function Setup Others
C) Password Change
Others
RATING EXPLANATIONS
• All : Parental control is inactive; all discs can play back.
•8 [Adult] : DVD software of any grades (adult/general/children) can be played
back.
•7 [NC-17] : No one under 17 admitted.
•6 [R] : Restricted; under 17 requires accompanying parent or adult guardian.
•5 [PGR] : Parental guidance recommended.
•4 [PG13] : Unsuitable for children under 13.
•3 [PG] : Parental guidance suggested.
•2 [G] : General audience.
•1 [Kid Safe] : Suitable for children.
1) Use [U / V] to select “Password Change”, then press [ENTER].
2) Enter a new 4-digit password, then press [ENTER].
3) Press [SETUP] to exit.
Others
Angle Icon Screen Saver Auto Power Off Panel Display Slide Show DivX(R) VOD Closed Caption
Off On On Bright 5sec
Off
• For how to select the setting items and options, refer to “Custom” on page 30.
Others
Remote Control Setting HDMI CEC Media Select Network Connection Network Update
BD1 On Disc Enable(Easy)
Setting items Options Description
Angle Icon On
Off*
On: The angle icon appears on the screen when playback the scene
with various angle. Off:
The angle icon disappears on the screen.
Screen Saver On*
Off
On: If this unit is left with no activity for more than 5 minutes, the
screen saver will be activated. Off:
Sets off the screen saver.
Auto Power Off On*
Off
On: If this unit is left with no activity for more than 30 minutes, this unit turns to the standby mode
automatically. Off:
Sets off the auto power off.
Panel Display
Sets the brightness of the front panel display.
Bright* Dimmer Auto
Bright: Front panel display gets brighter.
Dimmer: Front panel display gets darker.
Auto: Front panel display gets darker during playback.
Slide Show
Sets the display time for
5sec*
10sec the still picture (in JPEG format) playback.
Remote control operation
buttons
:
Displaying the menu Cancel the menu
:
Move the cursor (Up/Down/Left/Right)
37
ENGLISH
: Confirm the setting : Return to previous menu
ENGLISH
Function Setup Function Setup
Setting items Options Description
DivX(R) VOD Registration Code
Your registration code is:
cccccccccc
To learn more visit www.divx.com/vod
This menu item provides you with the DivX The DivX
required when downloading the DivX
®
®
®
VOD files from the Internet.
To learn more about DivX visit www.divx.com/vod.
Deactivation Code Your deactivation code is:
cccccccc
To learn more visit www.divx.com/vod
This menu item provides you with the DivX The DivX
required when re-downloading the DivX
®
®
®
Internet after deactivating. To learn more about DivX
www.divx.com/vod.
Deactivation Yes
No*
This menu deactivates the DivX®VOD files and provides you
with new registration code and deactivation code in order to
download the DivX from the Internet.
Closed Caption
Sets whether to display
On
Off* the closed caption or not using the caption decoder (commercially available ).
Remote Control Setting
Changes the signal code
BD1*
BD2 of a remote control. (Refer to page 6.)
VOD registration code. registration code is
®
VOD,
VOD deactivation code. deactivation code is
VOD files from the
®
VOD, visit
®
VOD files
Setting items Options Description
HDMI CEC
Sets whether to utilize
On* Off
the HDMI CEC function.
Media Select
Select the media to playback.
Disc* SD Card
Disc: Select this when you play back a
disc. SD Card:
Select this when you play back a SD Memory Card.
Network Connection
Refer to “Network Connection” on page 39 for more details of each setting.
Connection Test Perform the network connection
test to check if the network settings are correctly made.
Enable(Easy)* Set all the network settings to the
default settings. (In most cases, you can connect to the Internet without making any changes to the default settings.)
Enable(Custom) Set the network settings manually
in accordance with your network environment, if necessary.
Disable Deactivate the network
connection.
Network Update
Refer to “Network Update” on page 41 for
Yes No*
You can update the firmware version by connecting this unit to the Internet.
more detail.
Introduction Connections Playback Function Setup Others
Remote control operation
buttons
:
Displaying the menu Cancel the menu
:
Move the cursor (Up/Down/Left/Right)
38
ENGLISH
: Confirm the setting : Return to previous menu
ENGLISH
Function Setup Function Setup
Network Connection
Introduction Connections Playback Function Setup Others
Connection Test
After you made IP address/DNS settings or when a LAN cable is connected, always perform the connection test to check if the connection is correctly made.
1) Press [SETUP] in stop mode.
2) Use [Y / Z] to select , then press [ENTER].
If you want to set the network settings back to the default settings as above (except “BD-Live Setting”), follow the procedure below.
1) Follow steps 1) to 4) in “Connection Test” on this page.
2) Use [U / V] to select “Enable(Easy)”, then press [ENTER].
• The unit will start the connection test automatically and the test result will appear right after the test finishes.
• After the connection test finishes, press [ENTER] to go to network status confirmation screen.
3) Press [ENTER] to activate the network settings and set the network connection automatically. Press [SETUP] to exit.
3) Use [Y / Z] to select , then press [ENTER].
4) Use [U / V] to select “Network Connection”, then press [ENTER].
5) Use [U / V] to select “Connection Test”, then press [ENTER].
Connection test will start automatically and the test result will appear right after the connection test finishes.
Note
• The setting of “BD-Live Setting” will not be set back to the default, even if you follow the procedure.
• “Testing...” : The test is in progress.
• “Pass” : Connection test is successfully completed.
• “Fail” : Connection test failed. Check the connection settings.
Press [ENTER] to go to the list of network status confirmation screen.
Enable(Custom)
If you need to set specific settings manually in accordance with your network environment, select “Enable(Custom)” to set each setting as necessary.
IP Address Setting
Connection Test
IP Address Subnet Mask
Default Gateway Primary DNS Secondary DNS
then press ‘ENTER’.
∗∗∗ . ∗∗∗ . ∗∗∗ . ∗∗∗ ∗∗∗ . ∗∗∗ . ∗∗∗ . ∗∗∗ ∗∗∗ . ∗∗∗ . ∗∗∗ . ∗∗∗ ∗∗∗ . ∗∗∗ . ∗∗∗ . ∗∗∗ ∗∗∗ . ∗∗∗ . ∗∗∗ . ∗∗∗
6) Press [ENTER] to go back to the previous screen or press [SETUP] to exit.
1) Follow steps 1) to 4) in “Connection Test” on this page.
2) Use [U / V] to select “Enable(Custom)”, then press [ENTER].
3) Use [U / V] to select “IP Address Setting”.
4) Press [ENTER] repeatedly to select the desired setting.
“Auto(DHCP)” : If your router has DHCP server function, select “Auto(DHCP)”. “Manual” : If your router does not have DHCP server function, select “Manual”.
If you select “Manual”, follow the following instruction to set the IP address.
Use [U / V] to select “IP Address”, then press [ENTER].
• IP address setting screen will appear. Enter IP address, subnet mask and default gateway with
[U / V / Y / Z] and [the Number buttons].
Note
• If the connection test passes, you can enjoy the BD-Live functions using the Internet without making any extra settings.
• If the connection test fails, you may need to change the MAC address settings of your router. You can check the MAC address of this unit at the bottom of the “Enable(Custom)” screen.
Enable(Easy)
Network settings are set to the following settings initially. (In most cases, you can connect to the Internet without making any changes to the default settings.)
- IP Address Setting Auto(DHCP)
- DNS Setting Auto(DHCP)
- Proxy Setting Do Not Use
- Connection Speed Auto
- BD-Live Setting Allow
IP Address Setting
IP Address
Subnet Mask
Default Gateway
then press ‘ENTER’.
∗∗∗ ∗∗∗ ∗∗∗∗∗∗
.
.
∗∗∗∗∗∗ ∗∗∗∗∗∗
∗∗∗∗∗∗ ∗∗∗∗∗∗
.
.
.
.
.
.
.
• Enter the IP address number after checking the specifications of your router.
• If the IP address number is unknown, check the IP address number of other devices. (e.g. PC connected via LAN cable) and assign a different number from those of other devices.
After you enter all correctly, press [ENTER].
• Confirmation message will appear.
Remote control operation
buttons
:
Displaying the menu Cancel the menu
:
Move the cursor (Up/Down/Left/Right)
39
ENGLISH
: Confirm the setting : Return to previous menu
ENGLISH
Function Setup Function Setup
Proxy Setting
IP Address Setting
Is Setting OK?
IP Address Subnet Mask Default Gateway
No Yes
∗∗∗ . ∗∗∗ . ∗∗∗ . ∗∗∗ ∗∗∗ . ∗∗∗ . ∗∗∗ . ∗∗∗ ∗∗∗ . ∗∗∗ . ∗∗∗ . ∗∗∗
1) Follow steps 1) to 2) in “IP Address Setting” on page 39.
2) Use [U / V] to select “Proxy Setting”.
3) Press [ENTER] repeatedly to select the desired setting.
• For default settings, select “Do Not Use”.
• Please use this setting when instructed by your Internet service provider.
If you select “Use”, follow the following instruction to set the proxy address and proxy port.
Proxy Address
Use [U / V] to select “Yes”, then press [ENTER] to complete the setting.
5) Press [SETUP] to exit.
DNS Setting
1) Follow steps 1) to 2) in “IP Address Setting” on page 39.
2) Use [U / V] to select “DNS Setting”.
3) Press [ENTER] repeatedly to select the desired setting.
“Auto(DHCP)” : If your router has DHCP server function select “Auto(DHCP)”. “Manual” : If your router does not have DHCP server function, select “Manual”.
If you select “Manual”, follow the following instruction to set the DNS.
Use [U / V] to select “Primary DNS”, then press [ENTER].
• DNS setting screen will appear. Enter primary DNS and secondary DNS with [U / V / Y / Z] and [the Number buttons].
DNS Setting
Primary DNS
Secondary DNS
then press ‘ENTER’.
• Enter the numbers instructed by your Internet provider.
• If the number is unknown, check the number of other devices (e.g. PC connected via LAN cable) and assign the same number.
After you enter all correctly, press [ENTER].
• Confirmation message will appear.
.....
∗∗∗ ∗∗∗ ∗∗∗∗∗∗
∗∗∗∗∗∗ ∗∗∗∗∗∗
.
Use [U / V] to select “Proxy Address”, then press [ENTER]. Enter proxy address.
• The keyboard screen will appear.
Proxy Address
∗∗∗∗∗∗∗∗∗∗∗∗_
1
2
34567890
a
bcde fghij
k
l mnopqr st
u
vwxyz. -_OK
Clear All Clear OKa/A/@
[U / V / Y / Z] : Move the highlight.
[the Number buttons] : Enter number.
[ENTER] : Enter the highlighted number/word.
[RED] : Clear the entered number or word.
[GRN] : Clear all the entered numbers or words.
[BLU] : Switch between abc ? ABC ? @!?
[YEL] : Set the entered number or word.
After you enter all correctly, press [YEL].
• Confirmation message will appear.
Proxy Address
Is Setting OK?
************
Introduction Connections Playback Function Setup Others
DNS Setting
Is Setting OK?
Primary DNS Secondary DNS
No Yes
∗∗∗ . ∗∗∗ . ∗∗∗ . ∗∗∗ ∗∗∗ . ∗∗∗ . ∗∗∗ . ∗∗∗
Use [U / V] to select “Yes”, then press [ENTER] to complete the setting.
4) Press [SETUP] to exit.
:
Remote control operation
buttons
Displaying the menu Cancel the menu
:
Move the cursor (Up/Down/Left/Right)
40
ENGLISH
No Yes
Use [U / V] to select “Yes”, then press [ENTER] to complete the setting and go back to the proxy setting screen.
: Confirm the setting : Return to previous menu
ENGLISH
Function Setup Function Setup
Introduction Connections Playback Function Setup Others
Proxy Port
Use [U / V] to select “Proxy Port”, then press [ENTER].
• Proxy port setting screen will appear.
Enter proxy port number with [the Number buttons].
“10BASE Full” : Set the connection speed to “10BASE Full”.
“100BASE Half” : Set the connection speed to “100BASE Half”.
“100BASE Full” : Set the connection speed to “100BASE Full”.
4) Press [RETURN] to go back to previous screen, or press [SETUP] to exit.
Proxy Port
Please select the input Proxy Port. then press ‘ENTER’.
∗∗∗∗∗
After you enter all correctly, press [ENTER] to complete the setting.
4) Press [SETUP] to exit.
Note
For IP Address Settings and DNS Settings:
• The range of input number is between 0 and 255.
• If you enter a number larger than 255, the number will automatically be 255.
• The manually entered number will be saved even if you change the setting to “Auto(DHCP)”.
• When you enter a wrong number, press [CLEAR] to cancel. (The number will be back to “0”.)
• If you want to enter 1 or 2-digit number in one cell, press [Z] to move on to the next cell.
• If the entered IP address or the default gateway or primary DNS number is same as the default setting, IP address setting will be set to “Auto(DHCP)”. (The manually entered number will be saved.)
• When IP address setting is set to “Manual”, the setting of DNS setting will automatically be “Manual” and when IP address setting is set to “Auto(DHCP)”, you can set either “Auto(DHCP)” or “Manual” for DNS setting.
For Proxy Settings:
• The range of input number for the proxy port number is between 0 and 65535. (If you enter a number larger than 65535, it will be regarded as 65535.)
• For proxy port, the selected ports may be blocked and not be able to use depending on your network.
Connection Speed
You can set connection speed as your preference. (The default setting is “Auto”.)
1) Follow steps 1) to 2) in “IP Address Setting” on page 39.
2) Use [U / V] to select “Connection Speed”, then press [ENTER].
3) Use [U / V] to select the desired setting, then press [ENTER].
“Auto” : Set the appropriate connection speed automatically, in accordance with your
network environment.
“10BASE Half” : Set the connection speed to “10BASE Half”.
BD-Live Setting
You can limit the Internet access from the BD-Live functions. (The default setting is “Allow”.)
1) Follow steps 1) to 2) in “IP Address Setting” on page 39.
2) Use [U / V] to select “BD-Live Setting”, then press [ENTER].
3) Use [U / V] to select the desired setting, then press [ENTER].
“Allow” : Internet access is permitted from all BD-Live contents.
“Limited Allow” : Internet access is permitted only for BD-Live contents which have content
owner certificates. Internet access without the certificates are prohibited.
“Prohibit” : Internet access is prohibited from all BD-Live contents.
4) Press [RETURN] to go back to previous screen, or press [SETUP] to exit.
Disable
You can deactivate all the network connection and settings by following the instructions below.
1) Follow steps 1) to 4) in “Connection Test” on page 39.
2) Use [U / V] to select “Disable”, then press [ENTER].
3) Press [RETURN] to go back to previous screen, or press [SETUP] to exit.
Note
• The network connection can be reactivated by setting the network connection to “Enable(Easy)” or “Enable(Custom)”.
Network Update
You can update the software by connecting the unit to the Internet.
1) Follow steps 1) to 3) in “Connection Test” on page 39.
2) Use [U / V] to select “Network Update”, then press [ENTER].
• Confirmation message will appear.
3) Use [U / V] to select “Yes”, then press [ENTER].
• This unit will start checking for the latest firmware version.
4) Confirmation message will appear. Use [U / V] to select “Yes”, then press [ENTER].
• The unit will start downloading the latest firmware version.
5) When the download completes, confirmation message will appear. Press [ENTER].
• The unit will start updating the firmware version.
• It may take a while to complete the updating. (Please wait until “100%” appears on the front
panel display.)
6) After updating finishes, this unit will restart and open the disc tray automatically.
Remote control operation
buttons
:
Displaying the menu Cancel the menu
:
Move the cursor (Up/Down/Left/Right)
41
ENGLISH
: Confirm the setting : Return to previous menu
ENGLISH
Function Setup Function Setup
Note
• Please do not unplug the AC cord or LAN cable while executing the “Network Update”.
• All settings will remain the same even if you update the firmware version.
• The disc tray will open automatically after updating finishes. This is not a malfunction.
Initialize
Initialize the setting or SD Memory Card.
Initialize
Setup Format SD Card Erase Saved BD-ROM Data (Player) Erase Saved BD-ROM Data (SD Card) Network Settings
• For how to select the setting items and options, refer to “Custom” on page 30.
Setting items Options Description
Setup Yes
No*
Format SD Card Yes
No*
Erase Saved BD-ROM Data (Player)
Yes No*
Yes: Resets all settings in setup, except
for “Ratings” and “Network Connection”, to the factory default.
No: Does not perform the initialization.
Yes: Re-format SD Card.
No: Does not perform the initialization.
Yes: Re-format BD-ROM Data (Player) used for BD-Java.
No: Does not perform the initialization.
1) Press [SETUP] in stop mode.
2) Use [Y / Z] to select , then press [ENTER].
3) Use [U / V] to select a desired option, then press [ENTER].
4) Confirmation message will appear. Use [U / V] to select “Yes”, then press [ENTER].
5) Press [SETUP] to exit.
Note
• Do not remove the SD Memory Card while executing the “Format SD Card” or “Erase Saved BD-
• “Format SD Card” and “Erase Saved BD-ROM Data (SD Card)” are not available when a Blu-ray
Setting items Options Description
Erase Saved BD-ROM Data (SD Card)
Yes No*
Yes: Re-format BD-ROM Data (SD Card) used for BD-Java.
No: Does not perform the initialization.
Network Settings Yes
No*
Yes: Initialize all the network settings.
No: Does not perform the initialization.
“Setup” : All the settings except for the “Ratings” and “Network
Connection” setting will be reset to default.
“Format SD Card” : Initialize the SD Memory Card. “Erase Saved BD-ROM Data (Player)” : BD-ROM data for Player used for BD-Java will be
initialized.
“Erase Saved BD-ROM Data (SD Card)” : BD-ROM data for SD Card (available only when an SD
Memory Card is inserted) used for BD-Java will be initialized.
“Network Settings” : Reset the network setting to the default.
ROM Data (SD Card)”. It will damage the card.
Disc is in the unit.
Introduction Connections Playback Function Setup Others
Remote control operation
buttons
:
Displaying the menu Cancel the menu
:
Move the cursor (Up/Down/Left/Right)
42
ENGLISH
: Confirm the setting : Return to previous menu
ENGLISH
Introduction Connections Playback Function Setup Others
Others
Trademark Information Explanation of Terms
Numerics
4:3 Letter Box
When a wide (16 : 9) disc is played back by connecting a 4 : 3 TV Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories.
Manufactured under license under U.S. Patent #’s: 5,451,942; 5,956,674; 5,974,380; 5,978,762; 6,226,616; 6,487,535; 7,392,195; 7,272,567; 7,333,929; 7,212,872 & other U.S. and worldwide patents issued & pending. DTS is a registered trademark and the DTS logos, Symbol, DTS-HD and DTS-HD Master Audio | Essential are trademarks of DTS, Inc. ©1996-2008 DTS, Inc. All Rights Reserved.
HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.
“x.v.Color” and the “x.v.Color” logo are trademarks of Sony Corporation.
Java and all other trademarks and logos are trademarks or registered trademarks of Sun Microsystems, Inc. in the United States and/or other countries.
“AVCHD” and the “AVCHD” logo are trademarks of Panasonic Corporation and Sony Corporation.
DivX®, DivX Certified®, and associated logos are trademarks of DivX, Inc. and are used under license.
Windows Media and the Windows logo are trademarks or registered trademarks of Microsoft Corporation in the United States and/or other countries.
“BONUSVIEW” is a trademark of Blu-ray Disc Association.
“BD-LIVE” logo is trademark of Blu-ray Disc Association.
“Blu-ray Disc” and are trademarks.
is a trademark of DVD Format/Logo Licensing Corporation.
is trademark of Eastman Kodak Company.
and the BD5004, this function plays back the image with black
area at the top and bottom.
4:3 Pan-and-Scan
When a wide (16 : 9) disc is played back by connecting a 4 : 3 TV
and the BD5004, this function cuts left and right of the played
back image to the 4 : 3 size according to the disc’s control
information.
A
Analog Audio
An electrical signal that directly represents sound. Compare this to
digital audio which can be an electrical signal, but is an indirect
representation of sound. See also “Digital Audio”.
Aspect Ratio
This is the length and width ratio of the TV screen. The
conventional TV’s screen ratio is 4 : 3 and the wide screen TV’s
screen ratio is 16 : 9.
AVCHD
AVCHD is a new format for high definition video camcorders
which can record and play high-resolution HD images.
B
BD-J (Java)
With BD-Videos, there are fun software with more interactive
functions (games) using Java applications.
BD-Live
BD-Live is a BD-Video (BD-ROM version 2 Profile 2.0) which
contains new functions (e.g. Internet connection), in addition to
the BONUSVIEW function.
Bit Rate
This expresses the read amount per 1 second of video/audio data
recorded in a disc.
Blu-ray Disc
This is one-side 1 layer disc having 25GB capacity and can record
high vision video movie and games.
43
ENGLISH
ENGLISH
Others Others
BONUSVIEW
Special images for BD-Videos. It includes comment of the movie director, simultaneously developing sub-story, and images from different angles.
C
Chapter
This is a break intended by a producer who organizes the title of BD or DVD-Video. The chapter search function searches the beginning of this break.
Component Video Output
Each signal of luminance (Y) and component (PB/CB, PR/CR) is independent to output so that you can experience picture color as it is. Also, due to compatibility with progressive video (525p/ 480p), you can experience higher-density picture than that in interlace (525i/480i).
D
Deep Color
This technology allows expression of more number of colors than the conventional 8 bits and can reproduce colors close to natural ones without color streak.
DHCP (Dynamic Host Configuration Protocol)
This mechanism automatically perform network configuration such as IP address for network devices including BD5004, PC, and broadband router.
Digital Audio
An indirect representation of sound by numbers. During recording, the sound is measured at discrete intervals (44,100 times a second for CD audio) by an analog-to-digital converter, generating a stream of numbers. On playback, a digital-to-analog converter generates an analog signal based on these numbers. See also “Sampling Frequency” and “Analog Audio”.
®
DivX
DivX® is a codec (compression/decompression) that can compress pictures to a very small amount of data. The software can compress video data from almost any devices to the size that can be sent on the Internet without compromising visual quality of the pictures.
DNS Server
A server which translates Internet domain names into IP addresses.
Dolby Digital (5.1ch Surround)
This is a stereophonic effect developed by Dolby Laboratories. This is maximum 5.1 channels of independent multi-channel audio system.
Dolby Digital Plus
This is an extension version of Dolby Digital and is a high sound quality digital audio technology adopted as an optional audio for Blu-ray disc.
Dolby TrueHD
This lossless coding technology is adopted as optional audio for Blu-ray disc and supports 7.1 channels.
Downmix
This function converts the number of channels of surround audio to less number of channels and plays back.
DTS
This is an abbreviation of Digital Theater System, which is a digital audio system developed by DTS. When playing back audio by connecting this system with a device such as DTS amplifier, accurate sound field position and realistic sound effect as if you are in a movie theater can be obtained.
DTS-HD
This audio technology provides higher sound quality and enhanced functionality than the conventional DTS and is adopted as an optional audio for Blu-ray disc. This technology supports multi-channel, high data transfer speed, high sampling frequency, and lossless audio playback. Maximum 7.1 channels are supported in Blu-ray disc.
Dynamic Range
The difference between the maximum undistorted sound level and the minimum sound level that is discernible above the noise emitted by the device.
F
Finalize
This is processing that enables playing back of disc of BD/DVD/CD, which was recorded using a recorder, by other players.
G
Gateway
IP address of the electronic devices (such as router) which provide Internet access.
H
HDCP
When transmitting digital signals between devices, this copyright protection technology encrypts the signals to prevent content from being copied without authorization.
HDMI
This is an abbreviation of High-Definition Multimedia Interface,
which is an AV digital interface that can be connected to a TV or
amplifier. Video signal and audio signal can be connected using 1
cable.
Hub
A device used for connecting multiple devices to the network.
I
Interactive Audio
Audio such as click sound that is generated during operation and
is recorded in the title of BD-Videos.
Interlacing (interlaced scanning)
This conventional method used to project images on a TV displays
1 frame of image in half and half, respectively as 2 fields.
IP Address
A set of numbers which are assigned to devices participating in a
computer network.
J
JPEG (Joint Photographic Experts Group)
JPEG is a method of compressing still picture files. You can copy
JPEG files on disc or SD Memory Card from a computer and play
back the files on this unit.
L
LAN (Local Area Network)
A group of computer networks covering a small area like a
company, school or home.
Linear PCM
This signal is uncompressed PCM (Pulse Code Modulation) signal.
This is the same system as the CD audio but this uses 192kHz,
96kHz, and 48kHz sampling frequencies in BD or DVD and
provides higher sound quality than CD.
Local Storage
A storage area of sub contents for playing virtual packages on
BD-Video.
M
MPEG
This is an abbreviation of Moving Picture Experts Group, which is
an international standard of the moving picture audio
compression method. Images of BD and DVD are recorded using
this method.
Introduction Connections Playback Function Setup Others
44
ENGLISH
ENGLISH
Others Others
Introduction Connections Playback Function Setup Others
P
S
PCM (Pulse Code Modulation)
The most common system of encoding digital audio, found on CD and DAT. Excellent quality, but requires a lot of data compared to formats such as Dolby Digital and MPEG audio. For compatibility with digital audio recorders (CD, MD and DAT) and AV amplifiers with digital inputs, this unit can convert Dolby Digital and MPEG audio to PCM. See also “Digital Audio”.
Picture-in-Picture
This BD-Video function allows you to view making or commentary scenes in the secondary video while viewing the main story in the primary video.
Popup Menu
This menu recorded in BD software. While playing back a BD, this menu can be displayed on the front of the screen and can be operated.
Primary Audio
This audio signal is recorded in the main story in BD-Video.
Progressive (sequential scanning)
This is a scanning system of video signal that displays 1 frame of video as one image. Compared to the interlace system, this system provides images with less flickering and bleeding.
Proxy Server
Proxy server is a server which acts as an intermediary between a workstation user and the Internet to ensure security.
R
Rating
Depending on the age of the viewer, this function restricts playing back of BD-Video or DVD-Video. BD5004 can be set to restrict viewing in 1 to 254 level for BD-Video, and 1 to 8 level for DVD­Video.
Region Code
This code indicates country or region where the BD or DVD-Video can be played back.
Router
A networking device which distinguishes the IP address assigned to each device and routing and forwarding information in the computer network.
Sampling Frequency
The rate which sound is measured by a specified interval to turn into digital audio data. The numbers of sampling in one second defines as sampling frequency. The higher the rate, the better the sound quality.
Secondary Audio
The audio signals recorded in the BONUSVIEW of BD-Video. (e.g. Comment of movie director)
Subnet Mask
A mask which is used to determine what subnet an IP address belongs to.
T
Title
This is the unit of content that consists of chapters of BD or DVD­Video. Some BD or DVD-Video may include multiple titles.
V
Virtual Package
The function which copies data to other media (local storage) from the Internet and play the secondary video, secondary audio and the subtitle at the same time. The method of the playback varies depending on discs.
W
Windows Media™ Audio
Windows Media™ Audio is the audio compressing technology developed by Microsoft. You can copy Windows Media™ Audio files on disc or SD Memory Card from a computer and play them back on this unit.
X
x.v.Color
“x.v.Color” is a promotion name given to the products that have the capability to realize a wide color space based on the xvYCC specifications and is a trademark of Sony Corporation.
45
ENGLISH
ENGLISH
Others Others
Index
) A page
A-B Repeat ................................................................................................. 8, 20
AC cord
....................................................................................................... 3, 16
Angle .................................................................................................... 8, 22, 37
Aspect ratio .............................................................................................31, 43
Audio language
Audio signal .....................................................................................13, 14, 34
Audio stream/channel ...............................................................................24
AVCHD .................................................................................3, 4, 5, 13, 14, 43
) B page
BD audio mode ......................................................................................25, 33
BD-Live ................................................................................... 3, 15, 29, 41, 43
BD-Video
Brightness ........................................................................................... 9, 26, 37
) C page
CD-DA ................................................................................................................ 4
CD-RW/-R ......................................................................................................4, 5
Channel level .................................................................................................35
Chapter
Component video cable ....................................................................... 7, 12
Connections .......................................... 11, 12, 14, 15, 16, 38, 39, 40, 41
) D page
Dialog speed .................................................................................................. 19
Dimmer ....................................................................................................... 9, 37
Disc menu
DivX® ........................................................ 3, 4, 5, 13, 14, 26, 27, 28, 31, 44
DivX® VOD ...............................................................................................27, 38
Dolby Digital
Dolby Digital Plus .................................................... 13, 14, 25, 33, 34, 44
Dolby TrueHD ............................................................ 13, 14, 25, 33, 34, 44
DRC (Dynamic Range Control)
DTS ......................................................................... 13, 14, 25, 33, 34, 43, 44
DTS-CD .............................................................................................4, 5, 13, 14
DTS-HD
DVD-RW/-R ............................................................................................4, 5, 18
DVD-Video ......................................................................................4, 5, 13, 14
............................................................................................24
.........................................................................................4, 5, 13, 14
..................................................................................5, 20, 22, 23, 44
........................................................................................... 9, 18, 31
.............................................................. 13, 14, 25, 33, 34, 44
........................................................... 3, 34
.................................................................13, 14, 25, 33, 34, 43, 44
) F page
Fast forward Fast reverse
Format ..................................................................... 4, 13, 14, 27, 32, 33, 34
) H page
HDMI cable ................................................................................................7, 12
HDMI Deep Color ................................................................................. 32, 44
HDMI resolution ....................................................................................... 7, 13
) I page
Initialize ............................................................................................................42
Interactive audio ............................................................................ 25, 33, 44
Interlace ............................................................................................ 13, 32, 44
) J page
JPEG ........................................................................ 3, 4, 5, 26, 27, 28, 37, 44
) L page
LAN cable ...................................................................................................7, 15
Language code ..................................................................................... 31, 48
) M page
Marker ..............................................................................................................22
MP3 ................................................................................ 3, 4, 5, 13, 14, 26, 27
) N page
Network update .................................................................................... 38, 41
Noise reduction .............................................................................................26
) O page
On-screen display .............................................................................. 3, 8, 23
) P page
Parental Password
Pause ...................................................................................................7, 8, 9, 18
Picture Adjustment ......................................................................................26
Picture control
Playback (BD/DVD/AVCHD) ................................................ 17, 18, 19, 20
Playback (DivX®/MP3/WMA/JPEG) ............................ 19, 20, 21, 26, 27
Playback (DVD-RW/-R)
......................................................................................... 8, 9, 19
........................................................................................... 8, 9, 19
.................................................................................................... 36, 37
................................................................................................. 36, 37
................................................................................................. 3
........................................................................ 18, 21
Playback (Kodak Picture CD)
Playback (SD Card) ............................................................................... 28, 29
Popup menu
Program playback .......................................................................................20
Progressive ....................................................................................... 13, 32, 45
Pure direct mode
) R page
Random playback ....................................................................................8, 21
RCA audio cable ...........................................................................3, 7, 12, 15
RCA video cable .................................................................................. 3, 7, 12
Region code
Remote control ............................................................................... 6, 7, 8, 38
Repeat playback .......................................................................................8, 20
Resume playback
) S page
SD Card
Sharpness
Slow forward .............................................................................................9, 19
Source Direct ................................................................................... 10, 13, 32
Speaker setting
Step by step playback ................................................................................ 19
Subtitle language ........................................................................................ 25
Supplied accessories
) T page
.................................................................................. 5, 18, 20, 22, 23, 45
Title
Top menu
Track .............................................................................................. 5, 20, 22, 23
) V page
Virtual surround ........................................................................................... 25
) W page
Windows Media™ Audio
) X page
x.v.Color ...............................................................................................3, 43, 45
) Z page
Zoom ............................................................................................................8, 21
.......................................................................................9, 18, 45
.................................................................................. 10, 25
...............................................................................................5, 45
......................................................................................... 18
..............................................................................4, 7, 28, 29, 38, 42
....................................................................................................... 26
...............................................................................34, 35, 36
..........................................................................................................8
...................................................................28
.....................................................................................3
........................................3, 4, 5, 13, 14, 26, 27
Introduction Connections Playback Function Setup Others
46
ENGLISH
ENGLISH
Others Others
Introduction Connections Playback Function Setup Others
If the unit does not perform properly when operated as instructed in this user guide, check the unit, consulting the following checklist.
Troubleshooting
Problem Solution Page
No power - Check if the AC cord is properly connected.
No sound or picture - Check if the connected display device is turned on.
Distorted picture - Sometimes a small amount of picture distortion may appear.
Completely distorted picture or black/white picture with BD/DVD
No sound or distorted sound - Adjust the volume.
Picture freezes momentarily during playback
Disc cannot be played back - Clean the disc.
SD Memory Card cannot be read - The format of the card does not match to this unit or the card is not
No return to start-up screen when disc is removed
The unit does not respond to the remote control
- Unplug the AC cord once, and wait for 5-10 seconds and then plug it in again.
- Check the HDMI connection. (Check the status of the HDMI related indications.)
- Check the RCA audio/video cable connections.
- Check if the pure direct mode is set to “VideoOff” or “All Off”. If it is the case, set it to “Disp.Off” or “Normal”.
- Check whether the connected display device or other device supports HDCP. (This unit will not output a video signal unless the other device supports HDCP.)
- Check whether the output format of this unit (HDMI FORMAT) matches the supported input format of other connected device.
- Check if the “HDMI Deep Color” is set to “Auto”. If it is the case, set it to “Off”.
This is not a malfunction.
- Connect this unit directly to the TV. If the RCA audio/video cables are connected to a VCR, pictures may be distorted due to the copy protection system.
- Make sure the disc is compatible with this unit. 4
- Check that the speakers are connected correctly.
- Check the HDMI connections.
- Check the “Audio” settings.
- Check the disc for fingerprints/scratches and clean with a soft cloth wiping from center to edge.
- Clean the disc.
- Ensure the disc label is facing up.
- Check if the disc is defective by trying another disc.
- Cancel the ratings control or change the control level.
- Insert a correct disc that can be played back on this unit.
compatible.
- Reset this unit by turning it off, then on again.
- Aim the remote control directly at infrared sensor window on the front of the unit.
- Reduce the distance to infrared sensor window.
- Replace the batteries in the remote control.
- Re-insert the batteries with their polarities (+/- signs) as indicated.
- Make the signal code of the remote control match to the signal code of the unit.
– –
12
12, 15
25
14
12, 31, 32
32
12
12, 14, 15
12
33, 34
3
3
3
17
36
4
6
– 6 6 6
Problem Solution Page
Buttons do not work or the unit stops responding
The unit does not respond to some operating commands during playback
The unit cannot read BD/DVD/CD - Condensation? (Let sit 1 or 2 hours)
Angle does not switch - The angle cannot be switched for BD/DVD which do not contain
Playback does not start when the title is selected
The password for rating level has been forgotten
Cannot connect to the network - Check if the LAN cable connection is properly made.
Cannot connect to the network while my PC is connected to the network
Cannot use the BD-Live function - Use an SD card with enough space.
The playback of BD-Video or download of data does not perform properly
“HDCP NOK” appears on the front panel display
- To completely reset the unit, unplug the AC cord from the AC outlet for 5-10 seconds.
- Operations may not be permitted by the disc. Refer to the instructions of the disc.
- You are attempting to play a disc other than one with one of the marks on page 4.
- Wipe the dirt off the disc or replace the disc.
multiple angles. In some cases multiple angles are only recorded for specific scenes.
- Check the “Ratings” setting. 36
- Enter the default password “4737”, then your forgotten password will be cleared.
- Turn on the modem or broadband router.
- Check the network settings.
- Check if the broadband router and/or modem is correctly connected.
- Check the “BD-Live Setting”.
- Check the content of your Internet service contract to see if your Internet Service Provider prevents multiple terminals connecting at the same time.
- Remove the write protection of an SD card.
- Check if an SD card is correctly inserted.
- Do not remove the card during playback as some BD-Videos require an SD card during playback.
“HDCP NOK” appears under the following conditions:
- When the connected device does not support HDCP.
- When the connected device is recognized as an HDCP incompatible by HDMI SRM.
- When the connected device supports HDCP but cannot be recognized as an HDCP compatible for some reason.
Note
• Some functions are not available in specific modes, but this is not a malfunction. Read the description in this user guide for details on correct operations.
• Some functions are prohibited on some discs.
17
2 4
3
22
36
15
– 39 15 41
28 29
10
47
ENGLISH
ENGLISH
Others Others
Language Code
Introduction Connections Playback Function Setup Others
Language Code
A-B
Abkhazian 4748 Afar 4747 Afrikaans 4752 Albanian 6563 Amharic 4759 Arabic 4764 Armenian 5471 Assamese 4765 Aymara 4771 Azerbaijani 4772 Bashkir 4847 Basque 5167 Bengali;Bangla 4860 Bhutani 5072 Bihari 4854 Bislama 4855 Breton 4864 Bulgarian [BUL] 4853 Burmese 5971 Byelorussian 4851
C-E
Cambodian 5759 Catalan 4947 Chinese [CHI] 7254 Corsican 4961 Croatian 5464 Czech [CZE] 4965 Danish [DAN] 5047 Dutch [DUT] 6058 English [ENG] 5160
Language Code
Esperanto 5161 Estonian 5166
F-H
Faroese 5261 Fiji 5256 Finnish [FIN] 5255 French [FRE] 5264 Frisian 5271 Galician 5358 Georgian 5747 German [GER] 5051 Greek [GRE] 5158 Greenlandic 5758 Guarani 5360 Gujarati 5367 Hausa 5447 Hebrew 5569 Hindi 5455 Hungarian [HUN] 5467
I-K
Icelandic [ICE] 5565 Indonesian 5560 Interlingua 5547 Interlingue 5551 Inupiak 5557 Irish [IRI] 5347 Italian [ITA] 5566 Japanese [JPN] 5647 Javanese 5669 Kannada 5760 Kashmiri 5765 Kazakh 5757
Language Code
Kinyarwanda 6469 Kirghiz 5771 Kirundi 6460 Korean [KOR] 5761 Kurdish 5767
L-N
Laothian 5861 Latin 5847 Latvian;Lettish 5868 Lingala 5860 Lithuanian 5866 Macedonian 5957 Malagasy 5953 Malay 5965 Malayalam 5958 Maltese 5966 Maori 5955 Marathi 5964 Moldavian 5961 Mongolian 5960 Nauru 6047 Nepali 6051 Norwegian [NOR] 6061
O-R
Occitan 6149 Oriya 6164 Oromo(Afan) 6159 Panjabi 6247 Pashto;Pushto 6265 Persian 5247 Polish [POL] 6258 Portuguese [POR] 6266
Language Code
Quechua 6367 Rhaeto-Romance 6459 Romanian [RUM] 6461 Russian [RUS] 6467
S
Samoan 6559 Sangho 6553 Sanskrit 6547 Scots Gaelic 5350 Serbian 6564 Serbo-Croatian 6554 Sesotho 6566 Setswana 6660 Shona 6560 Sindhi 6550 Singhalese 6555 Siswat 6565 Slovak [SLO] 6557 Slovenian 6558 Somali 6561 Spanish [SPA] 5165 Sundanese 6567 Swahili 6569 Swedish [SWE] 6568
T
Tagalog 6658 Tajik 6653 Tamil 6647 Tatar 6666 Telugu 6651 Thai 6654 Tibetan 4861
Language Code
Tigrinya 6655 Tonga 6661 Tsonga 6665 Turkish [TUR] 6664 Turkmen 6657 Twi 6669
U-Z
Ukrainian 6757 Urdu 6764 Uzbek 6772 Vietnamese 6855 Volapuk 6861 Welsh 4971 Wolof 6961 Xhosa 7054 Yiddish 5655 Yoruba 7161 Zulu 7267
Note
• If you choose a language that has a 3-letter-language code (written in bracket), the code will be displayed every time you change the audio or subtitle language setting on pages 24-25. If you choose any other languages, ‘---’ will be displayed instead.
48
ENGLISH
ENGLISH
Others Others
Introduction Connections Playback Function Setup Others
Specifications
SIGNAL SYSTEM
NTSC color
APPLICABLE DISCS
(1) BD/DVD-Video Discs
1-layer 12cm single-sided discs, 2-layer 12cm single-sided discs, 2-layer 12cm double-sided discs (1 layer per side) / 1-layer 8cm single-sided discs (DVD)
(2) BD-RE/BD-R (Recorded in BDMV format)
1-layer 12cm single-sided discs, 2-layer 12cm single-sided discs 1-layer 8cm single-sided discs, 2-layer 8cm single-sided discs
(3) DVD-R
1-layer 12cm single-sided discs, 2-layer 12cm single-sided discs 1-layer 8cm single-sided discs, 2-layer 8cm single-sided discs
(4) DVD-RW
1-layer 12cm single-sided discs 1-layer 8cm single-sided discs
(5) Compact discs (audio CD)
12cm discs, 8cm discs
(6) CD-RW/-R
12cm discs, 8cm discs
APPLICABLE MEMORY CARDS
(1) SD Memory Card (2) SDHC Memory Card (3) miniSD Card (4) microSD Card
VIDEO OUTPUT
Y output level: 1Vp-p (75Ω/ohms) Output connectors: Pin jack, 1 set
COMPONENT OUTPUT
Y output level: 1Vp-p (75Ω/ohms) PB/CB output level: 0.7Vp-p (75/ohms)
R/CR output level: 0.7Vp-p (75Ω/ohms)
P Output connectors: Pin jacks, 1 set
HDMI OUTPUT
Output jack: 19-pin HDMI terminal, 1 set HDMI ver. 1.3a (Deep Color, Dolby Digital Plus, Dolby TrueHD, DTS-HD)
NETWORK TERMINAL
10BASE-T/ 100BASE-TX, 1 set
ANALOG AUDIO OUTPUT
Output level: 2Vrms (10kΩ/kohms) 2 channel (L, R) output connector: Pin jacks, 1 set
AUDIO OUTPUT PROPERTIES
(1) Frequency response
1 BDs (linear PCM) : 20Hz to 22kHz (48kHz sampling)
: 20Hz to 44kHz (96kHz sampling) : 20Hz to 88kHz (192kHz sampling)
2 DVDs (linear PCM) : 20Hz to 22kHz (48kHz sampling)
: 20Hz to 44kHz (96kHz sampling)
3 CDs : 20Hz to 20kHz (2) S/N ratio : 115dB (3) Total harmonic distortion : 1kHz 0.004% (4) Dynamic range : 100dB (BD/DVD) / 98dB (CD)
DIGITAL AUDIO OUTPUT
Coaxial digital output: Pin jack, 1 set
POWER SUPPLY
AC 120V, 60Hz
POWER CONSUMPTION
30W (Standby: 0.6W)
MAXIMUM EXTERNAL DIMENSIONS
W : 440mm (17-3/8") H : 105mm (4-3/16") D : 324mm (12-13/16") (including protruding parts)
MASS
4.3 kg (9.5 lbs)
REMOTE CONTROL
RC004BD Infrared pulse type Supply: DC 3V, 2 R6/AA batteries External dimensions:
W : 52mm (2-1/16")
H : 227mm (8-15/16")
D : 30mm (1-3/16") Mass: 138g (0.3 lbs) (including batteries)
440.0 (17-3/8)
8.0 (3/8)
282.0 (11-1/8)
324.0 (12-13/16)
34.0 (1-3/8)
91.0 (3-5/8)
105.0 (4-3/16)
14.0 (9/16)
• For purposes of improvement, specifications and design are subject to change without notice.
49
ENGLISH
Printed in China 07/2009 541110331126M mzh-d
E5KB1UD / 1VMN27773A ★★★★
Loading...