Makita BHP441Z, BHP441 Manual
ENGLISH
INSTRUCTION MANUAL
Cordless Percussion-Driver Drill
BHP441
BHP451
006749
WARNING:
For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
ENGLISH
SPECIFICATIONS
Model |
|
BHP441 |
|
BHP451 |
|
|
|
Concrete |
14 mm |
|
16 mm |
|
|
Steel |
13 mm |
|
13 mm |
Capacities |
|
Wood |
50 mm |
|
65 mm |
|
|
Wood screw |
6 mm x 75 mm |
|
10 mm x 89 mm |
|
|
Machine screw |
|
6 mm |
|
|
|
High (3) |
|
0- 1,700 |
|
No load speed (min-1) |
|
Medium (2) |
|
0 - 600 |
|
|
|
Low (1) |
|
0 - 300 |
|
|
|
High (3) |
|
0 - 25,500 |
|
Blows per minute (min-1) |
|
Medium (2) |
|
0 - 9,000 |
|
|
|
Low (1) |
|
0 - 4,500 |
|
Overall length |
|
250 mm |
|
250 mm |
|
Net weight |
|
2.1 kg |
|
2.2 kg |
|
Rated voltage |
|
D.C. 14.4 V |
|
D.C. 18 V |
|
•Due to our continuing programme of research and development, the specifications herein are subject to change without notice.
•Note: Specifications may differ from country to country.
END001-1
Symbols
The following show the symbols used for the equipment. Be sure that you understand their meaning before use. 
Only for EU countries
Do not dispose of electric equipment together with household waste material! In observance of European Directive 2002/96/EC on waste electric and electronic equipment and its implementation in accordance with national law, electric equipment that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility.
ENE039-1
Intended use
The tool is intended for impact drilling in brick, concrete and stone as well as for drilling without impact in wood, metal, ceramic and plastic.
For Model BHP441
ENG101-1
For European countries only Noise
The typical A-weighted noise level determined according to EN60745-2-1:
Sound pressure level (LpA) : 85 dB(A) Uncertainty (K) : 3 dB(A)
The noise level under working may exceed 85 dB (A).
Wear ear protection.
ENG203-1
Vibration
The vibration total value (tri-axial vector sum) determined according to EN60745-2-1:
Work mode: impact drilling into concrete
Vibration emission (ah,ID) : 10.5 m/s2 Uncertainty (K) : 1.5 m/s2
ENG302-1
Work mode : drilling into metal
Vibration emission (ah,D) : 2.5 m/s2 or less
For Model BHP451
ENG102-1
For European countries only Noise
The typical A-weighted noise level determined according to EN60745-2-1:
Sound pressure level (LpA) : 86 dB(A) Sound power level (LWA) : 97 dB(A) Uncertainty (K) : 3 dB(A)
Wear ear protection
ENG203-1
Vibration
The vibration total value (tri-axial vector sum) determined according to EN60745-2-1:
Work mode: impact drilling into concrete
Vibration emission (ah,ID) : 10.0 m/s2 Uncertainty (K) : 2.5 m/s2
ENG302-1
Work mode : drilling into metal
Vibration emission (ah,D) : 2.5 m/s2 or less
2
ENH102-7
EC-DECLARATION OF CONFORMITY
Model; BHP441,BHP451
We declare under our sole responsibility that this product is in compliance with the following standards of standardized documents;
EN60745, EN55014 in accordance with Council Directives, 2004/108/EC, 98/37/EC.
CE2007
000230
Tomoyasu Kato
Director Responsible Manufacturer:
Makita Corporation
3-11-8, Sumiyoshi-cho, Anjo, Aichi, JAPAN Authorized Representative in Europe:
Makita International Europe Ltd.
Michigan Drive, Tongwell, Milton Keynes, Bucks MK15 8JD, ENGLAND
GEA002-3
GENERAL SAFETY RULES
WARNING! Read all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. The term "power tool" in all of the warnings listed below refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.
SAVE THESE INSTRUCTIONS.
Work area safety
1.Keep work area clean and well lit. Cluttered and dark areas invite accidents.
2.Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
3.Keep children and bystanders away while operating a power tool. Distractions can cause
you to lose control.
Electrical Safety
4.Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.
5.Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
6.Do not expose power tools to rain or wet conditions. Water entering a power tool will
increase the risk of electric shock.
7.Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.
8.When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk of electric shock.
Personal Safety
9.Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.
10.Use safety equipment. Always wear eye protection. Safety equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.
11.Avoid accidental starting. Ensure the switch is in the off-position before plugging in. Carrying power tools with your finger on the switch or plugging in power tools that have the switch on invites accidents.
12.Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
13.Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
14.Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
15.If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used.
Use of these devices can reduce dust-related
hazards.
Power tool use and care
16.Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.
17.Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
18.Disconnect the plug from the power source
3
and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
19.Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
20.Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tools operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
21.Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
22.Use the power tool, accessories and tool bits etc. in accordance with these instructions and in the manner intended for the particular type of power tool, taking into account the working
conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.
Battery tool use and care
23.Ensure the switch is in the off position before inserting battery pack. Inserting the battery pack into power tools that have the switch on invites accidents.
24.Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.
25.Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.
26.When battery pack is not in use, keep it away from other metal objects like paper clips, coins, keys, nails, screws, or other small metal objects that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.
27.Under abusive conditions, liquid may be ejected from the battery, avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical
help. Liquid ejected from the battery may cause irritation or burns.
SERVICE
28.Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power
tool is maintained.
29.Follow instruction for lubricating and changing accessories.
30.Keep handles dry, clean and free from oil and grease.
GEB003-2
SPECIFIC SAFETY RULES
DO NOT let comfort or familiarity with product (gained from repeated use) replace strict adherence to hammer drill safety rules. If you use this power tool unsafely or incorrectly, you can suffer serious personal injury.
1.Wear ear protectors with impact drills.
Exposure to noise can cause hearing loss.
2.Use auxiliary handles supplied with the tool.
Loss of control can cause personal injury.
3.Hold power tools by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord. Contact with a "live" wire will make exposed metal parts of the tool "live" and shock the operator.
4.Always be sure you have a firm footing.
Be sure no one is below when using the tool in high locations.
5.Hold the tool firmly with both hands.
6.Keep hands away from rotating parts.
7.Do not leave the tool running. Operate the tool only when hand-held.
8.Do not touch the bit or the workpiece immediately after operation; they may be extremely hot and could burn your skin.
9.Some material contains chemicals which may be toxic. Take caution to prevent dust inhalation and skin contact. Follow material supplier safety data.
SAVE THESE INSTRUCTIONS.
WARNING:
MISUSE or failure to follow the safety rules stated in this instruction manual may cause serious personal injury.
ENC007-2
IMPORTANT SAFETY
INSTRUCTIONS
FOR BATTERY CARTRIDGE
1.Before using battery cartridge, read all instructions and cautionary markings on (1) battery charger, (2) battery, and (3) product
4
Loading...