Magellan 508 Instruction Manual

MiVue 5 Series
User Manual
508 538
Connect with us
@MagellanGPS
Magellan’s Take-Back Program provides a way for consumers to recycle certain Magellan equipment. As part of this program, all Magellan GPS models will be accepted.
Visit magellanGPS.com for more information.
Please check with your state or local law
Magellan MiVue
enforcement for applicable regulations regarding mounting to the windshield.
The driver should enter data or program the Magellan receiver only when the vehicle is stopped. Only a vehicle passenger should enter data or program the receiver while the vehicle is moving.
It is your responsibility to comply with all traffic laws.
Every attempt is made to ensure that the database is accurate. However, roadways, points of interest (POIs), and business and service locations may change over time.
Keep the receiver safe from extreme temperature conditions. For example, do not leave it exposed to direct sunlight for an extended period of time. The maximum operating temperature is 140°F (60°C).
Take care when mounting the receiver in your vehicle, whether using the windshield mount or other mount or accessories, that it does not obstruct the driver’s view of the road, interfere with the operation of the vehicle’s safety devices such as airbags, or present a hazard to occupants of the vehicle should the receiver be dislodged while driving.
You assume the risks associated with damage to your vehicle or vehicle occupants as the result of your choices in mounting the receiver.
The battery is rechargeable and should not be removed. In the event it should need to be replaced, please contact Magellan Technical Support.
FCC RF Radiation Exposure Statement
1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.
Wi-Fi 5G Band 1 is for indoor use only.
Canada, Industry Canada (IC) Notices
This device complies with Industry Canada licence­exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Canada, avis d’Industry Canada (IC)
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
508/538/638/658WIFI
Tested To Comply With
CC Standards
F
FOR HOME OR OFFICE USE
2
Getting to know the recorder
* Available on certain models
1
Device mount socket
For the device mount.
2
Mini-USB connector
Connects to the charger.
3
HD OUT connector*
Connects to an external device.
4
LCD screen
5
Buttons
Navigate menu settings
6
LED indicator 1
Indicates the system status of the recorder.
7
Power key
8
Memory card slot
Data is recorded to a MicroSD card.
9
Speaker
Outputs audio.
10
Camera lens
11
LED indicator 2
Indicates the Parking mode of the recorder.
12
Microphone
Allows you to record the video with sounds.
3
Power key
Once the vehicle engine is started, the recorder automatically turns on. By default, the recording will start right after the recorder turns on.
You can do the following using the Power key:
To manually turn the recorder on and off, press and
hold the Power key for 2 seconds.
When the recorder is turned on, press the Power key
to switch the LCD screen on/off.
LED indicators
Status LED 1 LED 2
The power cable is connected and the recorder is on:
The battery is charging, and
- the recording is in progress.
- the recording stops.
The battery is fully charged, and
- the recording is in progress.
- the recording stops.
Parking mode is enabled, and the power cable is disconnected:
The parking recording is in progress. The parking recording stops.
Green, Amber /
Blinking
Green / On
Red / Blinking
OFF
Red / Blinking
OFF
OFF OFF
OFF OFF
Red / Blinking Red / Blinking
4
Using the Function keys
The device provides four function keys to control the corresponding icons displayed at the bottom of the LCD screen. The key’s function may vary on different screens. For example, the device will display four icons as shown below while continuous recording is in progress.
Example Button Description
Icon Description
/ Recording with sound is enabled/disabled.
Press to enter the Settings Menu.
Press to manually enable Parking mode.
Press to take a photo.
Press to manually start an event recording.
The REC icon blinks while recording is in progress.
Displays the current time.
The GPS signal icon indicates the GPS status. *
The Battery icon indicates the remaining battery power.
* GPS enabled units only
5
Inserting a memory card
You must insert a memory card before you can start recording.
1. Hold the card by the edges and gently insert it into the slot with the label facing the rear side of the recorder.
2. To remove card, gently push the top edge of the card inwards to release it, and pull it out of the slot.
CAUTION:
DO NOT apply pressure to the center of the memory card. Use a Class 10 memory card with at least 8GB capacity. The recorder supports
memory cards with up to 32GB capacity.
Magellan does not guarantee the product’s compatibility with memory cards
from all manufacturers.
Before you start recording, please format the memory card to avoid
malfunction caused by files not created by the recorder. You can format the card on your computer or on the recorder (by selecting Settings Menu > Format).
Please turn the device off before removing the memory card.
6
Using your recorder in a vehicle
1. Make sure that your car is parked on a level ground.
2. Follow the instruction below to mount your recorder in a vehicle securely.
3. Connect the car charger to the vehicle power plug. Route the cables through the top ceiling and the A-pillar so that it does not interfere with driving. Ensure the cable installation does not interfere with the vehicle's airbags or other safety features.
7
Loading...
+ 18 hidden pages