Linear AM-MIO Owner's Manual

AM-MIO

(760) 438-7000

USA & Canada (800) 421-1587 & (800) 392-0123

Toll Free FAX (800) 468-1340

www.linearcorp.com

POWER SUPPLY MODULE (PSM

)

NOTE: ILLUSTRATION SHOWS FOUR RELAY/LOOP MODULES, ONLY ON

MODULE IS INCLUDED WITH THE AM-MIO

RELAY/LOOP MODULES (RLM) (FOUR MODULES MAXIMUM

)

BACKUP BATTERY 12 VOLT 7 AMP/HOUR MAXIMUM (NOT INCLUDED)

MODULE MOUNTING RACKS

CAREFULLY ROUTE THE BATTERY LEADS UNDER MODULE RACK AS SHOW

SLIDE MODULES OUT OF THE RACK

PSM

PLACE COVER ON CARPET AND PUNC

H OUT KEY LOCK KNOCKOUT

INSERT LOCK INTO COVER

TIGHTEN NUT

RELAY/LOOP

MODULE (RLM

)

POWER SUPPL

MODULE (PSM

)

BACKUP

BATTER

LEAD

DEVICE

ADDRESS

SELECTOR

DATA

POWER SUPPLY

STATUS

INDICATORS

TAMPER

LOW BATTER

AC POWE

TAMPER SWITCH

CONNECTOR

MODULE

CONNECTOR

CONTROLLER

CONNECTOR

POWER

TERMINALS

AUXILIARY

PBUS

TERMINAL

RELAY

STATUS

INDICATORS

LOOP STATUS

INDICATO

DEVICE ADDRESS

SELECTO

MODULE

CONNECTOR

RELAY TRIGGER

PUSHBUTTONS

RELAY

OUTPUT

TERMINALS

LOOP

INPU

TERMINALS

USE THE CABINET BOTTOM AS A TEMPLATE TO MARK THE FOUR KEYHOLE MOUNTING HOLE

FOR RECESSED WIRING, MARK WIRING SLOT

, THEN CUT OUT HOLE WITH DRYWALL SA

FOR CONDUIT WIRING

REMOVE ANY CABINE

T KNOCKOUTS BEFORE MOUNTING THE CABINE

USE THE APPROPRIAT

E HARDWARE TO MOUNT THE CABINE

NOTE: PSM DEFAULT ADDRESS IS "5"

NOTE: RLM DEFAULT ADDRESS IS "4

THE ARROW IN THE SELECTOR SWITCH SLOT POINTS TO THE ADDRESS NUMBER (ADDRESS NUMBERS 1-6 AR

VALID)

SET EACH MODULE TO A DIFFERENT DEVICE ADDRESS (ONLY REQUIRED IF ADDRESS OTHE

R THAN DEFAULT IS DESIRED)

RELAY/LOOP

MODUL

POWER SUPPL

MODUL

CONNECT POWER SUPPLY TO RELAY/LOOP MODUL

WITH THE 10-WIRE CABL

TO KEEP THE BATTERY LEADS AWAY FROM THE POWER SUPPL

Y HEAT SINK, ROUTE THE BATTERY LEADS UNDER MODULE RACK AS SHOW

SLIDE MODULES INTO RACK

PRESS THE MODULES IN UNTI

THEY SNAP INTO PLAC

PSM

REMOVE THE OPTIONAL JUMPER FROM THE TAMPER SWITCH CONNECTOR

INSTALL THE TAMPER SWITCH IN THE BOTTOM CORNER OF CABINET AND CONNECT TH

WIRE TO THE TAMPER SWITCH CONNECTO

ATTACH THE MAGNET TO THE CABINET COVER SO IT WILL ALIGN WITH TH

E TAMPER SWITCH WHEN THE COVER IS CLOSED

PLUG CABLE FROM AM-MIO PSM CONTROLLER CONNECTOR INTO THE CONTROLLER'S AM-MIO INTERFACE CONNECTOR (MODEL AM-3 CONTROLLER SHOWN)

TO AM-MIO PSM

OPTIONAL: USE THE PSM AUXILIARY PBUS TERMINALS TO CONNECT TO THE CONTROLLER'S AUXILIARY PBUS TERMINALS. REFERENCE THE PSM WIRING DIAGRAM. CABLE TYPE IS BELDEN 9931 (300 FEET MAX. CABLE RUN) OR WEICO 9405 (500 FEET MAX. CABLE RUN).

Input-Output Expansion Interface

For Use With the AM-3, AE-1000, & AE-2000 Access Control Systems

Installation Instructions

PRODUCT DESCRIPTION

The AM-MIO is an expandable input/output interface designed for use with Linear’s AM-3, AE-1000, & AE-2000 access control systems. Housed in a lockable cabinet, the basic AM-MIO consists of two modules: a power supply module (PSM) and a relay/loop module (RLM). Up to three additional RLM modules can be added to ﬁll the ﬁve-position module “rack”. Each RLM module provides six Form “C” (nor mally open & normally closed) 5-amp relays for outputs and eight supervised loop terminals for inputs. With four RLM modules, the AM-MIO is capable of controlling 24 relay outputs and 32 loop inputs. Each module has a rotary switch to select its unique remote device address. The device address identiﬁes each module to the system. Each module is interconnected to the controller by daisy-chained cables. Pushbuttons on the RLM module are provided for manually triggering each relay for testing. Each relay has a red LED light to show when it’s energized. A two-color red/ green LED on the RLM module displays the status of the loop inputs. If all eight loops are “normal” (not shorted or open) the indicator is green. If any of the eight loops are “abnormal” (shorted or open) the indicator is red. The power supply module distributes power to the RLM module(s). An external 16 VAC transformer powers the supply and provides charging current for a 12-volt backup battery (up to 7 amp/hour capacity). Indicators on the power supply module display its status. The green indicator lights when AC power is present and blinks when AC power is absent. The yellow indicator lights when the backup battery is low. Special power circuitry prevents fully discharging the backup batter y. The status of the power supply is checked regularly by the controller. The red DATA indicator lights when data transfers. The red TAMPER indicator lights and the controller is signaled when the optional magnetic tamper switch detects that the cabinet has been opened.

CABINET COMPONENTS

MODULE FEATURES KEY LOCK INSTALLATION (OPTIONAL) REMOVING MODULES

MOUNTING CABINET SETTING DEVICE ADDRESSES CONNECTING MODULES

INSTALLING MODULES CONNECTING TAMPER SWITCH (OPTIONAL) CONNECT TO ACCESS CONTROLLER

CONNECT RELAY OUTPUTS CONNECT LOOP INPUTS CONNECT AC POWER

N.O.1COM

N.C.3N.O.4CO

N.C.6N.O.7CO

N.C.

N.O.

COM11N.C.12N.O.13COM14N.C.15N.O.16COM17N.C.

CHANNEL 1 CHANNEL 2 CHANNEL 3

CHANNEL 4 CHANNEL 5 CHANNEL

CONNECT RELAY OUTPUTS TO TH

E CONTROLLED DEVICE

RELAY RATING

5 AMPS

14 VD

MAXIMU

LOOP

M11LOOP

2.2K 2.2K 2.2K 2.2K

CONNECT ANY INPUTS TO THE LOOP INPUT TERMINAL

EACH LOOP INPUT CAN BE TRIGGERED WITH A NORMALLY OPEN OR NORMALLY CLOSED SWITCH

ALL LOOP INPUTS MUST BE TERMINATED WITH A 2.2K END-OF-LINE RESISTOR

EXAMPLE OF LOOPS 1-4 WITH NORMALLY CLOSED SWITCHE

EXAMPLE OF LOOPS 5-

8 WITH NORMALLY OPEN SWITCHE

EART

GND

DATA

POWER

TERMINAL

16 VAC, 24 VA MIN.

POWE

TRANSFORME

UNIFIED EARTH GROUND

CONNECT 16 VAC POWER FROM PLUG-I

N TRANSFORMER TO POWER TERMINAL

1 &

CONNECT A GOOD EARTH GROUND TO POWER TERMINAL

NOTE: DATA GROUND TERMINAL IS USED ONLY WHEN CONNECTING TO THE CONTROLLE

THROUGH TH

E CONTROLLER AUXILIARY PBUS TERMINALS

PLACE THE BACKUP BATTERY IN THE CABINE

CONNECT THE RED LEAD TO BATTERY POSITIVE (+)

CONNECT THE BLACK LEAD TO BATTERY NEGATIVE (-)

PRESS THE RELAY TRIGGER BUTTONS TO TEST EACH RELA

CONNECTED

THE RELAY STATUS

INDICATOR WILL

LIGHT WHEN TH

RELAY IS ENERGIZED

CAUTION!

DEVICES CONNECTED TO

THE RELAYS WILL ACTIVATE

WATCH THE LOOP STATUS INDICATO

WHILE TESTING THE LOOP

GREEN = ALL LOOPS NORMAL

RED = ANY LOOP OPEN OR SHORTE

LOOP

COM LOO

LOOP3COM LOOP

2.2K 2.2K

LOOP

COM LOO

LOOP7COM LOOP

2.2K 2.2K

CHANNEL 2 CHANNEL

N.O.

CHANNEL

COM N.C. N.O. COM N.C. N.O. COM N.C

CHANNEL 5 CHANNEL

N.O.

CHANNEL 4

COM N.C. N.O. COM N.C. N.O. COM N.C

POWER TERMINALS

INACIN

EARTH

GND

DATA

GND

DAT1 DAT0 DVAL PCLK

AUXILIARY PBUS TERMINALS

RELAY OUTPUT TERMINAL

LOOP INPUT TERMINAL

ALL LOOP INPUTS MUST BE

TERMINATED WITH A 2.2K

END-OF-LINE RESISTOR

CONTROLLED DEVICE "4"

CONTROLLED DEVICE "5"

CONTROLLED DEVICE "6"

CONTROLLED DEVICE "1"

CONTROLLED DEVICE "2"

CONTROLLED DEVICE "3"

16 VAC, 24 VA

MINIMU

TRANSFORMER

EARTH

GROUND

STAKE

CONTROLLER PBUS TERMINALS

POWER SUPPLY

MODULE (PSM

)

RELAY/LOOP

MODULE (RLM)

AM-MIO RLM WIRING DIAGRAM

AM-MIO PSM WIRING DIAGRAM

12 VDC BACKUP

BATTERY

+ RED WIRE

- BLACK WIRE

NOTE: OPTIONAL AM-MIO PSM TO CONTROLLER WIRING SHOWN WHEN NOT USING THE INCLUDED CABL

1. PROGRAM THE ACCESS CONTROL SYSTEM. BE SURE TO PROGRAM TH

E SYSTEM FOR THE DEVICE ADDRESS OF EACH OF TH

AM-MIO MODULES.

2. USE ENTRY CODES OR TRANSMITTERS TO TEST ACTIVATE EACH OF TH

AM-MIO OUTPUT

3. TEST TO SEE IF EACH OF THE AM-MIO LOOP INPUTS (IF USED) ARE RECOGNIZED BY THE ACCESS CONTRO

SYSTEM

CONNECT BACKUP BATTERY TEST RELAYS TEST LOOPS

WIRING DIAGRAM

TEST SYSTEM LINEAR LIMITED WARRANTY

This Linear product is warranted against defects in material and workmanship for twenty four (24) months. The Warranty Expiration Date is labeled on the product. This warranty extends only to wholesale customers who buy direct from Linear or through Linear’s normal distribution channels. Linear does not warrant this product to consumers. Consumers should inquire from their selling dealer as to the nature of the dealer’s warranty, if any. There are no obligations

or liabilities on the part of Linear LLC for consequential damages arising out of or in connection with use or performance of this product or other indirect damages with respect to loss of property, revenue, or proﬁt, or cost of removal, installation, or reinstallation.

All implied warranties, including implied warranties for merchantability and implied warranties for ﬁtness, are valid only until Warranty Expiration Date as labeled on the product. This Linear LLC Warranty is in lieu of all

other warranties express or implied.

All products returned for warranty service require a Return Product Authorization Number (RPA#). Contact Linear Technical Service at 1-800421-1587 for an RPA# and other important details.

IMPORTANT !!!

Linear radio controls provide a reliable communications link and ﬁll an important need in portable wireless signalling. However, there are some limitations which must be observed.

• For U.S. installations only: The radios are required to comply with FCC Rules and Regulations as Part 15 devices. As such, they have limited transmitter power and therefore limited range.

• A receiver cannot respond to more than one transmitted signal at a time and may be blocked by radio signals that occur on or near their operating frequencies, regardless of code settings.

• Changes or modiﬁcations to the device may void FCC compliance.

• Infrequently used radio links should be tested regularly to protect against undetected interference or fault.

• A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale distributor or dealer, and these facts should be communicated to the ultimate users.