Linear AM-CRI Quick Start Manual
AM-CRI
INTRODUCTION
The AM-CRI card reader interface is designed for use with Linear’s
AE1000Plus, AE2000Plus, and AM3Plus access control systems. The
interface will support one or two 26-bit Weigand input devices.
If the readers used have a “hold” or “buffer” connection, two readers may
be used to the AM-CRI. If the readers do not have a “hold” or “buffer”
connection, one reader may be used with the AM-CRI.
1. TYPICAL INSTALLATION
ONE OR TWO READERS
CAN BE USED
AM-CRI
INTERFACE
(INSIDE WALL)
Usually mounted near the readers, the AM-CRI interface connects to the
controller through a six-wire cable. Each reader connects to the AM-CRI
Card
through a six-wire (one LED in reader) or seven wire (two LEDs in reader)
cable.
Reader
Interface
Installation Instructions
USA & Canada (800) 421-1587 & (800) 392-0123
(760) 438-7000 - Toll Free FAX (800) 468-1340
www.linearcorp.com
2. OPEN CASE 3. LOCATE COMPONENTS 4. MOUNT READERS
SQUEEZE
SIDES
TOGETHER
Two rotary switches in the AM-CRI select the PBUS device address for each
reader connected. Each remote PBUS device connected to the controller
must be set to a different device address. The address switches in the
AM-CRI must be set to different addresses if two readers are used.
Power is supplied to the interface and reader(s) from the controller. A power
selection jumper is provided for each reader. Five or eight volt power or
external power for locally powered readers can be selected.
READER "A"
DEVICE ADDRESS
READER "A"
TERMINALS
READER "A"
POWER JUMPER
SELECTOR
POWER & DATA
TERMINALS
(CONNECTS TO
CONTROLLER)
EACH AM-CRI EQUALS 25 LOAD UNITS
CABLE LENGTH FORMULA FOR EACH AM-CRI USED IN SYSTEM
CABLE RUN CABLE TYPE
120 FEET MAXIMUM
400 FEET MAXIMUM
BELDEN 9931 (24 AWG)
WEICO 9405 (20 AWG)
CABLE TO
CONTROLLER
(SEE FORMULA)
HOMERUN
WIRE EACH
AM-CRI TO THE
CONTROLLER
FORMULA
FEET x LOAD UNITS < 3,000 MAXIMUM
FEET x LOAD UNITS < 10,000 MAXIMUM
SEPARATE
CASE
READER "B"
TERMINALS
READER "B"
POWER JUMPER
READER "B"
DEVICE ADDRESS
SELECTOR
MOUNT READER(S)
PER MANUFACTURER'S
SPECIFICATIONS
5. CONNECT READERS TO AM-CRI 6. SET DEVICE ADDRESS AND POWER JUMPERS 7. CONNECT AM-CRI TO CONTROLLER
READER "B"
TERMINALS
PWR
GND
HOLD
LED1
LED1- ON
DURING
STANDBY
TWO READER
HOOKUP
WITH HOLD
READER "A" READER "B"
REFER TO READER MANUFACTURER'S SPECIFICATIONS
FOR READER WIRE COLOR AND HOOK UP DETAILS
LED2- ON
DURING
ACCESS
READER "A"
TERMINALS
DAT1
DAT0
LED2
LED1
HOLD
GND
PWR
LED2
DAT0
DAT1
READER "B"
TERMINALS
PWR
GND
HOLD
LED1
LED2
DAT0
DAT1
SINGLE
READER
HOOKUP
W/O HOLD
READER "B"
REFER TO STEP 3 ILLUSTRATION
FOR COMPONENT LOCATIONS
SET READER
POWER JUMPER
8 VOLT POWER
TO READER
REMOVE JUMPER WHEN
USING EXTERNAL POWER
NOTE:
5 VOLT POWER
TO READER
SET DEVICE
ADDRESS
SELECTOR
SET TO POSITION 1-6
(MUST BE DIFFERENT
FROM OTHER READER)
SET UNUSED READER
ADDRESS TO "0"
NOTE:
WHEN USING ONE READER WITHOUT A "HOLD" LINE,
CONNECT IT TO READER "B" TERMINALS AND SET
READER "A" DEVICE ADDRESS SELECTOR TO "0"
PWR
GND
AM-CRI
TERMINALS
DAT1
DAT0
DVAL
PCLK
USE CABLE FORMULA
TO DETERMINE CABLE
TYPE AND MAXIMUM
LENGTH
AM-CRI
NOTE: CONTROLLER MUST BE TURNED OFF BEFORE
MAKING ANY WIRING CONNECTIONS
PWR
GND
DAT1
DAT0
DVAL
PCLK
8. CLOSE CASE AND MOUNT UNIT 9. PROGRAM AND TEST LINEAR LIMITED WARRANTY
This Linear product is warranted against defects in material and
workmanship for twelve (12) months. This warranty extends only to
wholesale customers who buy direct from Linear or through Linear’s
normal distribution channels. Linear does not warrant this product
to consumers. Consumers should inquire from their selling dealer as
to the nature of the dealer’s warranty, if any. There are no obligations
or liabilities on the part of Linear LLC for consequential damages
arising out of or in connection with use or performance of this
product or other indirect damages with respect to loss of property,
revenue, or profi t, or cost of removal, installation, or reinstallation.
All implied warranties, including implied warranties for merchantability
and implied warranties for fi tness, are valid only until This Linear
LLC Warranty is in lieu of all other warranties express or implied.
SNAP CASE TOGETHER
PROGRAM THE CONTROLLER
TO CONFIGURE THE PBUS
DEVICE
ACCESS CONTROL
SYSTEM PBUS
TERMINALS
USE FOUR SCREWS
TO MOUNT THE
AM-CRI
All products returned for warranty service require a Return Product
Authorization Number (RPA#). Contact Linear Technical Services at
1-800-421-1587 for an RPA# and other important details
REFER TO THE CONTROLLER
PROGRAMMING INSTRUCTIONS
FOR DETAILS
Copyright © 2012 Linear LLC 211845 E
Loading...