Linear AK-3 User Manual

AK-3

Digital Keyless
Entry System

1

4

7

Installation and Programming Instructions

2

5

8

0

3

6

9

USA & Canada [phone] & [phone]

[phone]

Toll Free FAX [phone]

www.linearcorp.com

CONTENTS

COMPONENT LOCATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

WIRING DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Opening the Keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Install the Electrical Box and Mounting Plate . . . . . . . . . . . . . . . . . . . . . . 2

Final Keypad Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Keypad Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Solid State Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

FACTORY DEFAULTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

BASIC PROGRAMMING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

PROGRAMMING OPTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

RESETTING KEYPAD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Master Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Resetting the Master Code. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

AK-3 OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

LINEAR LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

IMPORTANT !!! . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

FCC NOTICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

INTRODUCTION

Linear’s AK-3 is a digital keyless entry system designed for access control
applications. The keypad is housed in a rugged, plastic enclosure and is
designed to be mounted in a standard single-gang electrical box. The die-cast
keys have bright, easy-to-read yellow graphics.

Up to 480 entry codes, from 1 to 6 digits in length, can be programmed. They can
activate either, or both, of the relay outputs. The “anti-passback” feature prevents
using the same code again before the programmed time elapses.

All system indicators are long-lasting, solid-state LEDs. Two indicators show the
status of the entry system. The left indicator lights red to indicate power, then
turns green when access is granted. The right indicator lights yellow when the
keypad is in “lockout” condition (from too many incorrect code entries). An internal
sounder beeps when each key is pressed. An internal jumper sets the sounder
volume high or low.

The SENSE input can be used two ways. If programmed for “door sense” the
input is wired to a normally closed switch on the door to detect when the door is
open or closed. Forced entry or door ajar situations can then be detected. Using
door sense, the “Auto-relock” feature will prevent “tailgating” by turning off the
Main Relay output immediately when the door is closed after access has been
granted. If the SENSE input is programmed for “inhibit”, the input can be wired
to a “service” switch or automatic timer that will disable the Main Relay when
required.

The REQUEST-TO-EXIT input can be wired to a pushbutton to provide
codeless activation of Main Relay, Auxiliary Relay, Output #3, or Output #4
(programmable).

The ALARM SHUNT output activates when access is granted. This output can
be wired to shunt alarm contacts on the access door/gate to prevent triggering of
an alarm when authorized access occurs.

The AK-3 is powered from a 12-24 Volt AC or DC source. Power can be obtained
from the access device or a separate power supply. The EEPROM memory
retains all entry codes and programming, even without power. An internal jumper
is provided to reset the master code. The Main Relay has a 5 Amp capacity.
The Auxiliary Relay has a 1 Amp capacity. Two solid state outputs, capable of
switching 100 mA to common, are programmable to signal forced entry, door ajar,
lockout, alarm circuit shunting, request-to-exit, and keypad active conditions.

FEATURES

✓ KEYPAD PROGRAMMABLE

No programmer required

✓ 480 ENTRY CODE CAPACITY

Ideal for small & medium traffi c installations

✓ 1-6 DIGIT ENTRY CODE LENGTH

Flexible code length for different applications

✓ 4 INDEPENDENT OUTPUTS (TIMED/TOGGLED)

Each output’s action is programmable

✓ 4 INDEPENDENT TIMERS

Each output’s activation time is programmable

✓ TWO FORM “C” (N.O. & N.C) RELAY CONTACTS

Main Relay 5-Amp @ 28 VDC capacity,
Auxiliary Relay 1-Amp @ 28 VDC capacity

✓ EACH ENTRY CODE CAN ACTIVATE EITHER OR BOTH RELAYS

Specifi c entry codes can grant access to different doors

✓ TWO SOLID STATE OUTPUTS

Auxiliary outputs can indicate access status on external devices

✓ TWO STATUS INDICATORS (2-COLOR RED/GREEN & YELLOW)

Displays access, lockout, and programming information

✓ PIEZO SOUNDER (TWO SELECTABLE VOLUME LEVELS)

Programmable for beeps during key presses and output activations

✓ TIMED ANTI-PASSBACK

Disables entry code for a programmed time after use

✓ AUTO-RELOCK

Releases the main relay as soon as the door shuts

✓ KEYPAD LOCKOUT

Locks the keypad after too many incorrect entries

✓ TACTILE KEY FEEL

Assures complete key presses

✓ DOOR SENSE INPUT

For sensing door position to control auto-relock and door-ajar features

✓ INHIBIT INPUT

For temporarily disabling access with a timer or switch

✓ REQUEST-TO-EXIT INPUT

For codeless activation with a pushbutton

✓ KEYPAD CAN BE POWERED FROM 12-24 VOLTS AC OR DC

Power can be supplied from a transformer, battery, or power supply

COMPONENT LOCATIONS

RED/GREEN
POWER/ACCESS
INDICATOR

KEYPAD

1

4

7

2

5

8

0

3

6

9

YELLOW
"LOCKOUT"
INDICATOR

TERMINAL
BLOCK #1
(TB1)

MOUNTING
PLATE

MASTER CODE
RESET JUMBER
(P5)

BEEPER
LEVEL
JUMPER (P4)

WIRING DIAGRAM

POWER
SUPPLY

ELECTRIC

DOOR

STRIKE

TO ALARM

SYSTEM

ALARM

CONTACT

Figure 1. Component Locations

TYPICAL DOOR INSTALLATION WIRING

TERMINAL

BLOCK 1

1 - AC OR DC

2 - AC OR DC

3 - N.O.

4 - COM

5 - N.C.

6 - N.O.

7 - COM

8 - N.C.

AK-3 TERMINALS

12-24 VOLT

AC OR DC

POWER

MAIN RELAY

5 AMPS @

28 VDC MAX.

AUXILIARY

RELAY 1 AMP

@ 28 VDC MAX.

SENSE - 8

GROUND - 7

REQUEST-TO-EXIT - 6

GROUND - 5

GROUND - 4

OUTPUT #3 - 3

OUTPUT #4 - 2

GROUND - 1

WIRES

GRAY

BLACK

VIOLET

BLACK

BLACK

BLUE

GREEN

BLACK

N.C. DOOR

SWITCH

REQUEST

TO EXIT

BUTTON

AUXILIARY

OUTPUTS
100 mA MAX.
TO COMMON

GROUND

STAK E

REQUIRED WIRING

OPTIONAL WIRING

OTHER WIRING

NOTES:

1. ALARM SHUNT SET FOR AUXILIARY RELAY

2. GRAY WIRE SET FOR DOOR SENSE

Figure 2. Wiring Diagram

CAUTION

IF THE UNIT IS AC POWERED,
MAK E SURE THE SECONDARY OF THE
SYSTEM TRANSFORMER IS ISOL ATED

FROM EARTH GROUND

1