Linear AE-2 Owner's Manual

INTRODUCTION

1. SYSTEM COMPONENT LOCATIONS

The Model AE-2 Telephone Entry Con trol Console is des igned for use as a pri mary
access control device for gated communities, parking garages, office buildings,
apartments, dormitories, hotels/motels, commercial buildings and recreational facilities.

AE-2

This unit is a fusion of Linear’s full-featured Model AM/II Access Control System and
the Model AE-2 Telephone Entry Module. Housed in a locked, rugged stainless steel

Telephone Entry Control Console

enclosure, the AE-2 features a 12-key telephone style keypad, a vacuum florescent
two-line directory display, and a built-in microphone and speaker.

All of the outstanding AM/II access control system functions are available with the AE-2 in
addition to hands-free, full duplex telephone communications with tenants or authorized
personnel for granting access. Entry codes can also be typed directly on the keypad.

In a typical installat ion, the unit’s mem ory would be program med with each tenant ’s
name and directory code number. A visitor would use the
view the director y names and code numb er for the desir ed party. Upon en tering the

or # key on the AE-2 to

*

directory number, the AE-2 will automatically dial the tenant’s telephone number and
establish two-way voice communication between the visitor and the tenant . T h e ten a n t
will then have the option to grant access to the guest by pressing a digit on their telephone.

In addition to the telephone entry, the AE-2 can grant access using various remote
devices that are commonly used with the AM/II. These devices include wireless
transmitters, proximity receivers, swipe card readers and remote keypads.

Mechanical & Electrical
Installation Instructions

The output relays can be programmed to control electric door strikes, door & gate
operators, barrier gates. CCTV cameras can also be triggered by the output relays to
monitor the entry areas.

All of the programming functions of the AE-2 can be performed directly through the
unit’s keypad. An optional telephone modem can be installed for easy remote

[phone] • FAX [phone]

USA & Canada [phone] & [phone]

Toll Free FAX [phone]

www.linearcorp.com

programming with a personal computer.
The AE-2 cabinet has provisions for installing a postal lock for keyed mail carrier access.

The postal lock can be programmed to activate any of the four output relays.

2. AE-2 COMPONENT LOCATIONS 3. DETERMINE MOUNTING LOCATION 4. MOUNT CABINET

MODULAR
TELEPHONE
JACK (HIDDEN)

HYBRID LEVEL
ADJUSTMENT
(FACTORY SET
DO NOT ADJUST)

SPEAKER
VOLUME
ADJUSTMENT

SPEAKER
CONNECTOR

AE-2 TO AM/II
INTERCONNECT
CABLE

TELEPHONE
LINE TERMINALS

TEST JUMPER
(REMOVE TO
HEAR UNIT DIAL)

MICROPHONE
& POSTAL KEY
SWITCH TERMINALS

BUSY INDICATOR
(LIGHTS WHEN AE-2 IS
COMMUNICATING OR WHEN
PHONE LINE IS DISCONNECTED)

ON-LINE INDICATOR
(LIGHTS WHEN PHONE
LINE IS ACTIVE)

DISPLAY
CONTRAST
ADJUSTMENT
(NOT USED ON
THIS MODEL)

THE AE-2 SHOULD BE MOUNTED IN A WELL LIT LOCATION NEAR THE
CONTROLLED OPENING. WIRING ACCESS FOR POWER, TELEPHONE,
EARTH GROUND, CONTROL OUTPUT AND ANTENNA CO-AX MUST BE
AVAILABLE BEHIND THE MOUNTING LOCATION.

AREA
LIGHTING

AE-2
TELEPHONE
ENTRY SYSTEM

CONTROLLED
ENTRY DOOR

5 3/8" 5 3/8"

5 3/8" 5 3/8"

MOUNTING
LOCATION

9 3/8"

MOUNT CABINET WITH
SUITABLE HARDWARE FOR
MOUNTING SURFACE.

USE TOGGLE BOLTS FOR
STUCCO WALL, WEDGE
ANCHORS OR EXPANSION
BOLTS FOR CONCRETE
WALL, LAG SCREWS FOR
WOOD WALL.

5. CONNECT WIRING 6. OPTIONAL MODEM INSTALLATION 7. OPTIONAL POSTAL LOCK INSTALLATION

REFER TO THE AM/II INSTALLATION & PROGRAMMING
INSTRUCTIONS FOR DETAILS ON WIRING POWER, EARTH
GROUND, REMOTE DEVICES, ANTENNA, CONTROL INPUTS AND
RELAY OUTPUTS TO THE AM/II

RELAY OUTPUT
TO ACCESS
DEVICE

POWER INPUT
TO TRANSFORMER

EARTH
GROUND
CONNECTION

USE LOWER
WIRING HOLE
IF MODEM IS
GOING TO BE
INSTALLED

TELEPHONE
LINE (USE
MODULAR
JACK OR
TERMINALS)

CONNECT UNITS
WITH THE MODEL
A2M MODEM CABLE

CONNECT
INCOMING
TELEPHONE
LINE TO THE
MODEM'S
"LINE" JACK

NOTE: SEPARATE PHONE LINES ARE
RECOMMENDED FOR THE MODEM AND AE-2.
ONE PHONE LINE CAN BE USED AS SHOWN
ALTHOUGH THE ENTRY SYSTEM IS
UNAVAILABLE WHILE MODEM IS ON-LINE.

ATTACH MODEM
WITH VELCRO ® STRIPS
(SEE MODEM INSTALLATION
INSTRUCTIONS)

USE THE TELEPHONE CABLE
SUPPLIED WITH THE MODEM TO
CONNECT BETWEEN THE
MODEM'S "PHONE" JACK AND THE
AE-2 TELEPHONE LINE JACK

CONNECT MODEM
TRANSFORMER
POWER CABLE
AND TURN MODEM
SWITCH ON

1

BARRIER PLATE

BEND UP TABS ON
THE HOLE PLUG AND
REMOVE THE PLUG

3

REMOVE THE TWO NUTS
AND THE POSTAL LOCK
BARRIER PLATE

2

INSTALL THE POSTAL
LOCK USING FOUR
10-32 NUTS

VERIFY THAT THE LOCK
STRIKE ACTIVATES THE
MICRO SWITCH

8. PROGRAM SYSTEM 9. ADJUST SPEAKER VOLUME & TESTING LINEAR LIMITED WARRANTY

INSTALLERS OF AE-2 SYSTEMS SHOULD
FAMILIARIZE THEMSELVES WITH THE
AM/II SYSTEM BY READING THE ENTIRE
AM/II INSTALLATION & PROGRAMMING
INSTRUCTIONS. PROGRAM AREAS
SPECIFIC TO THE AE-1 ARE AREAS 07 &

27. AREA 21 HAS TWO OPTIONS FOR THE
AE-2. PROGRAMMING WITH A PERSONAL
COMPUTER IS RECOMMENDED,
ESPECIALLY FOR ENTERING THE TENANT
NAMES.

AREA 21

RELAY SETUP

Which Relay to Program.
CH-A CH-B CH-C CH-D

Select Operation:
Control Shunt Alarm Obstacle CCTV

Select Timing Mode:
Time Pulse Toggle Latch

Enter Activation Time:
Time in seconds: 00000

Assign Time Zone [1]:
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

Assign Time Zone [2]:
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

Assign Time Zone [3]:
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

Assign Time Zone [4]:
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

Enter Channel Name

Assign Telephone Digit
None 1 2 3 4 5 6 7 8 9

Channel Control
Normal Activate LockOpen LockClosed

21.1

21.2

21.3

21.4

21.5

21.6

21.7

21.8

21.9

21.10

21.11

AREA 07

TELEPHONE ENTRY NUMBERS

Enter Directory Code
Directory Code: 0000

Enter Tenant Name

Enter Telephone Number
Telephone#: ************

Extended Talk Time
Yes No

Delete Directory Entry
Directory Code: 0000

AREA 27

TELEPHONE ENTRY SETUP

Directory Code Length
1 2 3 4

Directory Begins At
Beginning(A) Middle(M)

PBX Dialing Digit
Off 9 8 7 6 5 4 3 2 1 0

Set Talk Time
Talk Time Seconds: 060

Assign Postal Key Door
CH-A CH-B CH-C CH-D

Sort Directory Names
Yes No

Edit Display Messages
Message Number: 00

Edit Display Message

Max Directory Entries
Maximum Entries: 00000

Delete All Tlph. Entries
Yes No

Adjust Hybrid Level
Press OK To Start/Stop

Display Briteness
Dim Low Med High

Priority Access ABCD
0 = No 1 = Yes 0000

7.1

7.2

7.3

7.4

7.5

27.1

27.2

27.3

27.4

27.5

27.6

27.7

27.8

27.9

27.10

27.11

27.12

27.13

1

REMOVE
TEST JUMPER

ADJUST THE
SPEAKER VOLUME
AND DISPLAY
CONTRAST TO SUIT
THE ENVRONMENT
THE UNIT IS
MOUNTED IN

3

5

VERIFY THAT THE
PROPER RELAY
ACTIVATES AND
THAT THE ACCESS
DOOR STRIKE OR
GATE CONTROL
ACTIVATES

2

PRESS # TO VIEW
DIRECTORY AND
ENTER CODE TO
DIAL A TEST
PHONE NUMBER

4

HAVE TESTING
PARTY PRESS
ASSIGNED
TELEPHONE
DIGIT (DEFAULT
IS 9) TO GRANT
ACCESS

6

REPLACE THE TEST JUMPER,
LOCK THE CABINET AND
INSTRUCT FACILITY MANAGER
ON SYSTEM USE

This Linear product is warranted against defects in material and workmanship for twelve
(12) months. The Warranty Expiration Date is labeled on the product. This warranty
extends only to wholesale customers who buy direct from Linear or through Linear’s
normal distribut ion chann els. Linear does not warrant this product to consumers.
Consumers should inquir e from their selling dealer as to the nature of the de aler’s
warranty, if any. There are no obligations or liabilities on the part of Linear

Corporation for consequential damages arising out of or in connection with use
or performance of this product or other indirect damages with respect to loss of
property, revenue, or profit, or cost of removal, installation, or reinstallation. All

implied warranties, including implied warranties for merchantability and implied
warranties for f itness, ar e valid only unti l Warranty Expirati on Date as lab eled on the
product. This Linear Corporation Warranty is in lieu of all other warranties express

or implied.

All products returned for warranty service require a Return Product Authorization
Number (RPA#). Contact Linear Technical Services at 1-800-421-1587 for an RPA#
and other important details.

IMPORTANT !!!

Linear radio controls provide a reliable communications link and fill an important need
in portable wirel ess signaling. However, there are some lim itations which must be
observed.

For U.S. installations only: The radios are required to comply with FCC Rules and Regulat ion s as Part 15

✶

devices. As such, they have limited transmitter power and therefore limited ran ge.
A receiver cannot respond to more than one transmitt ed signa l at a time and ma y be blocked by rad io signals

✶

that occur on or near their operating f requen cie s, re gardle ss of code set tin gs.
Changes or modifications to the device may void FCC compliance.

✶

Infrequently used radio links should be tested regu larly to pro te ct ag ainst und et ecte d int er f ere nce or fa ult .

✶

A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale distributor or

✶

dealer, and these facts should be communicated to the ultima te users.

Copyright © 1999 Linear Corporation 215314 C