Linear 9510, 9520 Owner's Manual
9500 Series
714-996-4100 * 800-999-5225 * fax 714-996-4900 * www.channelplus.com
600-126 Rev.B ©1999 Multiplex Technology, Inc., Brea, Ca.
PERFORMANCE MULTI-ROOM VIDEO
Multiplex Technology, Inc. warrants this product to be free from
defects in materials and workmanship for a period of one year from
the date of purchase or MTI will repair, or at its option, replace the
defective product. To obtain warranty service, call MTI for a return
material authorization (RMA) number and return the product prepaid to Multiplex Technology, Inc., 3001 Enterprise Street, Brea, CA
92821, Attention: Customer Service. Please put the RMA number on
the outside of the carton.
Any implied warranty arising from the sale of the product including
implied warranties of merchantability and fitness for purpose are limited to the warranty stated above. MTI shall not be responsible for
losses or damages or expenses, whether direct, consequential or
incidental arising from the use of or the inability to use this product.
Some states do not allow limitations on how long the implied warranty lasts or the exclusions or limitations or incidental or consequential damages, so the above limitations and exclusions may not
apply to you. This warranty gives you specific legal rights, and you
may have other rights which may vary from state to state.
WARRANTY
Models
9510HHR B&W
9520HHR Color
9510BID B&W
9520BID Color
9510PAL B&W
Specifications: typical @ 25°C ± 5° C
9510 (B&W) 9510PAL(AUS) 9520 (Color)
lens viewing angle 78°
resolution: horizontal 525 lines 625 lines 525 lines
vertical 350 lines 350 lines 350 lines
standard lens cover: smoked
minimum light level 2 lux 2 lux 8 lux
video input format EIA CCIR NTSC
input signal 1.0 V peak-to-peak @ 75Ω
signal-to-noise ratio >45 dB
white balance automatic
electronic shutter speed automatic: 1/60 to 1/50,000 second
tuning range UHF 14 to 64 21 to 62(28 to 67) 14 to 64
CATV 65 to 125
A
65 to 125
A
power supply included with product
mains power 105 to 125 210 to 250 105 to 125
output of power supply 15VDC 600mA
general
injector module camera module
width x height x depth 6.5” x 3.5” x 1.25” 3.25” x 3.25” x 1.5”
(16.3cm x 9cm x 3.2cm) (8.2 cm x 8.2cm x 3.8cm)
shipping weight 2 lbs (0.9 kg)
operating temperature –4°F to 131°F (–20°C to 55°C)
A
excluding channels 95 through 99
The CatCam is a surveillance system that creates a new channel
to add to existing television channels. The new channel carries a
picture from the camera that is placed anywhere in the home. The
CatCam was designed to install effortlessly into existing coax home
wiring or into new construction.
Contents: Channel Injector
Camera
Power Injector
Power Supply
Coax Jumper
The CatCam is comprised of a camera and a channel injector. The
camera is designed to flush mount indoors or outdoors
(under an eaves
and not directly exposed to the elements)
using a deep double gang J box. The
channel injector is weather resistant and designed to mount indoors
or outdoors close to the incoming CATV or antenna feed. The system uses the existing coax cable distribution in the house.
The CatCam was designed to work with Cat 5 wiring. Although the
system will function with quad wire, Cat 5 delivers the highest quality
picture. The Cat 5 allows the use of an automatic line length sensor
and picture compensator. Quad wire does not take advantage of
this enhancement.
Model Differences:
The model 9500HHR series is a high headroom design for CATV
and off air antenna feeds only.
The model 9500BID series is a bi-directional design for use with
CATV cable boxes that are interactive or require bi-directional communications with the cable company.
The model 9510PAL is designed to modulate PAL frequencies and
use CATV or off air antenna feeds.
Installation:
First, locate the incoming CATV or antenna feed and install the
channel injector at that location.
Second, install the camera at the desired location and run Cat 5 wire
from the camera to the channel location.
Third, apply power and select an unused channel for the CatCam
picture to appear on all the televisions.
2
Installation: Step One
Locate the incoming CATV or antenna feed and existing splitter.
(Usually found on the side of the house, in the attic or near the electrical and phone service box)
Remove the lock screw located on the bottom of the channel
injector and slide the cover off. Use the mounting holes as shown to
affix the channel injector to the wall next to the splitter.
Disconnect the incoming CATV or antenna feed from the existing
splitter and attach it to the channel injector as shown.
Now attach the supplied coax jumper back to the existing splitter
and tighten all connections with a 7/16” wrench.
Use mounting
holes on the
bottom plate to
attach channel
injector to the
wall
Incoming CATV or
antenna coax
Out
to TVs
3
Incoming CATV or
antenna coax
Supplied coax
jumper goes back
to splitter
Out
to TVs
After
Before
Mount the
injector within
4” of the splitter
Mount the
injector within
4” of the splitter
© 1999
© 1999
Loading...