Life Fitness 9500L User Manual
Life Fitness Model 9500L Cross-Trainer
10
423
7
How To...Remove and Replace the 4”, and 14” Linkage Assemblies
Tools Required: Torx Key or Standard Screwdriver, Socket Set, Wrench Set, Hex Key Set Kit # GK53-00002-0021
IMPORTANT!
PLEASE READ THROUGH THESE INSTRUCTIONS BEFORE ATTEMPTING TO INSTALL THIS KIT.
FAILURE TO FOLLOW THE STEPS IN PROPER SEQUENCE COULD CAUSE DAMAGE TO THE EQUIPMENT.
1 Washer Qty: 4
0017-00104-0402
4 Metal Washer Qty: 4
0017-00104-0369
7 Bolt w/Locktite Qty: 2
0017-00101-1610
10 Bolt Qty: 2
0017-00101-1606
WARNING: FAILURE TO OBSERVE SAFETY PROCEDURES WHEN SERVICING THIS UNIT
COULD RESULT IN INJURY FROM ELECTRICAL SHOCK
1
2 Brass Washer Qty: 4
0017-00006-0226
5 Shouldered Sleeve Qty: 4
0K53-01346-0017
8 External Lock Washer Qty: 4
0017-00104-0302
11 Bolt Qty: 2
0017-00101-1608
3 Delrin Spacer Qty: 4
OK53-01384-0000
6 3/4” Sleeve Qty: 2
OK53-01342-0000
9 Jam Nut Qty: 4
0017-00103-0273
5
8 9
11
6
Life Fitness Model 9500L Cross-Trainer
N
O
UTV
5
How To...Remove and Replace Hardware in the 4”, and 14” Linkage Assemblies
(Continued)
Step 1
Turn power OFF at the On/Off switch and unplug the line cord from the
electrical outlet.
Step 2
Locate the two PUSH SNAP RIVETS (A) securing the top of the HOOD
SHROUD PANEL (B) to the top of the REAR SHROUD PANEL (C). The two
PUSH SNAP RIVETS are located on either side of the MONOCOLUMN (D)
under the TRAY ASSEMBLY (E). Depress the center button of each of the
two PUSH SNAP RIVETS to release the rivet locks.
HINT: USING A HEX KEY TOOL, YOU CAN REACH UNDER THE TRAY
ASSEMBLY TO DEPRESS THE RIVET LOCKS.
Step 3
Remove the eight SCREWS (F) securing the HOOD SHROUD PANEL (B) to the SIDE SHROUD PANELS (G).
Step 4
Carefully press down on the HOOD SHROUD PANEL (B) near the PUSH SNAP RIVETS (A) until the HOOD SHROUD
PANEL disengages from the PUSH SNAP RIVETS. Carefully remove the HOOD SHROUD PANEL from the unit and
set it aside.
Step 5
Pivot the user right PEDAL LEVER ASSEMBLY to it’s in the forward position.
Step 6
Locate the user right PEDAL LEVER ASSEMBLY (N) and the 4” LINK ASSEMBLY (O) pivot point. Using a 9/16”
socket and a 7/32” hex key, remove the NUT (P), two WASHERS (Q), and BOLT (R) from the PEDAL LEVER
ASSEMBLY (do not discard hardware) and the 4” LINK on the CRANK ARM
ASSEMBLY. Carefully rotate the 4” LINK BAR ASSEMBLY out of the way.
Remove and discard old SLEEVE and replace (in step 14) with 3/4” SLEEVE (#6)
included in the kit. Leave disconnected until step 14.
Step 7
CAUTION: BY REMOVING THE BOLT (V), YOU WILL BE SEPARATING THE
PEDAL LEVER ASSEMBLY AND THE 14” LINK BAR ( I ), THIS WILL CAUSE
THE CRANK ARM ASSEMBLY TO ROTATE.
SAFETY TIP: PLACE A BLOCK BETWEEN THE CRANK ARM PULLEY
ASSEMBLY AND FRAME TO PREVENT CRANK ARM ASSEMBLY
ROTATION.
Using two 9/16” wrenches, remove the NUT (S), METAL WASHER (T), PLASTIC WASHER (U), BOLT (V), and
SHOULDERED SLEEVE (#5) from the 14” LINK BAR ( I ) and the SMALL EXTENSION pivot point. Discard the old
SHOULDERED SLEEVE along with hardware and replace with hardware included in the kit.
Leave disconnected until step 15 for replacement directions.
6RQP
I S
Step 8
Carefully place the user right PEDAL LEVER ASSEMBLY (N) on the floor.
Loading...