LG DLEY1701V, DLEY1701VE, DLGY1702V, DLEY1701WE Owner’s Manual

<![if ! IE]>

<![endif]>FRANÇAIS ENGLISH

OWNER’S MANUAL

DRYER

Read this owner’s manual thoroughly before operating the appliance and keep it handy for reference at all times.

DLEY1701*E, DLGY1702*E

DLEY1701*, DLGY1702*

							www.lg.com
MFL67652510							Copyright © 2013 - 2017 LG Electronics Inc. All Rights Reserved.

2 TABLE OF CONTENTS

TABLE OF CONTENTS

3	PRODUCT FEATURES		43 smart features
		43		Tag On (on some models)
4	SAFETY INSTRUCTIONS		49 mAINTENANCE
5	IMPORTANT SAFETY INSTRUCTIONS
7	GROUNDING INSTRUCTIONS	49		Regular Cleaning
8	PRODUCT OVERVIEW		50	Troubleshooting
8	Parts	50		FAQs: Frequently Asked Questions
8	Accessories	50		User Support Videos
8	Two-Way Reversible Door (on some models)	51		Before Calling for Service
8	Safety Tether Kit (on some models)

9 INSTALLATION

9Installation Overview

9Product Specifications

10Installation Location Requirements

10Clearances

11Installing on a pedestal

12Leveling the Dryer

12 Reversing the Door

20Installing the Side Vent Kit

21Venting the Dryer

24 Connecting Gas Dryers

26 Connecting Electric Dryers

30Final Installation Check

31Installation Test (Duct Check)

33 OPERATION

33Using the Dryer

34Check the Lint Filter Before Every Load

34Sorting Loads

34Loading the Dryer

35Using the LG EasyLoadTM

36Control Panel

38Cycle Guide

39Cycle Settings and Options

42 Steam Functions (Steam Models)

58 SMART DIAGNOSIS™

58Using Smart DiagnosisTM

59WARRANTY (CANADA)

PRODUCT FEATURES 3

PRODUCT FEATURES

Easy-to-Use Control Panel

An entire selection of user-friendly functions make operating the dryer easy.

Two-way Easy-access Reversing Door

The LG EasyLoadTM can be tilted open from the top, hamper-style, allowing you to easily load the dryer without items falling on the floor. The door still swings open to provide easy access for unloading or loading of bulkier items. The door hinge can be reversed to adjust to the installation location.

Steam Functions (Steam Models)

LG's steam technology allows you to inject fabrics with a swirling jet of steam to refresh clothes, reduce static, and make ironing easier. Simply select the Steam FreshTM cycle or Wrinkle Care cycle.

Flow SenseTM Duct Blockage Sensing System Indicator

The Flow SenseTM duct blockage sensing system detects and alerts you to restrictions in the installed household ductwork that reduce exhaust airflow through the dryer. If you see the alert: Clean or repair the ducts to remove the restrictions. Keep your ducts free of blockage to help increase efficiency and reduce long drying times caused by blocked ducts.

Smart DiagnosisTM

Should you experience any technical difficulty with your dryer, it has the capability of transmitting data via your telephone to the Customer Information Center. The call center agent records the data transmitted from your machine and uses it to analyze the issue, providing a fast and effective diagnosis.

Tag On (on some models)

The Tag On feature works on most smart phones equipped with the NFC function and based on the Android operating system (OS).

Using the LG Smart Laundry & DW application, the Tag On feature will allow you to diagnose your appliance, download new cycles, and see the status of your appliance by simply touching the smart phone to the Tag On logo of the appliance.

E	S
D

C ER T

I

I

G
	N
		D
	E
I
F

Protocol P154

Sanitization Performance of Residential Clothes dryer

<![if ! IE]>

<![endif]>ENGLISH

4 SAFETY INSTRUCTIONS

SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USE

Your safety and the safety of others is very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word DANGER, WARNING, or CAUTION.

These words mean:

DANGER - You will be killed or seriously injured if you do not immediately follow instructions.

WARNING - You may be killed or seriously injured if you do not follow instructions.

CAUTION - You may be slightly injured or cause damage to the product if you do not follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what may happen if the instructions are not followed.

WARNING – Risk of Fire

Install the clothes dryer according to the manufacturer’s instructions and local codes.

•• Do not install a clothes dryer with flexible plastic venting materials. If flexible metal (foil type) duct is installed, it must be of a specific type identified by the appliance manufacturer as suitable for use with clothes dryers. Flexible venting materials are known to collapse, be easily crushed, and trap lint. These conditions will obstruct clothes dryer airflow and increase the risk of fire.

•• To reduce the risk of severe injury or death, follow all installation instructions.

•• Save these instructions.

WARNING

FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly could result in serious injury, death or property damage.

—Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

—WHAT TO DO IF YOU SMELL GAS

•Do not try to light any appliance.

•Do not touch any electrical switch; do not use any phone in your building.

•Clear the room, building or area of all occupants.

•Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

•If you cannot reach your gas supplier, call the fire department.

—Installation and service must be performed by a qualified installer, service agency or the gas supplier.

SAFETY INSTRUCTIONS 5

IMPORTANT SAFETY INSTRUCTIONS

Warning

To reduce the risk of fire, electric shock, or injury to persons when using your appliance, follow basic precautions, including the following:

Installation

•• Keep area around the exhaust opening and adjacent surrounding areas free from the accumulation of lint, dust, and dirt.

•• Do not install or store this appliance where it will be exposed to the weather.

•• Do not place items exposed to cooking oils in your dryer. Items contaminated with cooking oils may contribute to a chemical reaction that could cause a load to catch fire.

•• Properly ground the dryer to conform with all governing codes and ordinances. Follow the details in the installation instructions. Electric shock may result if the dryer is not properly grounded.

•• Before use, the dryer must be properly installed as described in this manual. Electric shock may result if the dryer is not properly grounded.

•• Install and store the dryer where it will not be exposed to temperatures below freezing or exposed to the weather.

•• All repairs and servicing must be performed by authorized service personnel unless specifically recommended in this Owner’s Manual. Use only authorized factory parts. Failure to follow this warning may result in serious injury, fire, electric shock, or death.

•• To reduce the risk of electric shock, do not install the dryer in humid spaces. Failure to follow this warning may result in serious injury, fire, electric shock, or death.

•• Connect to a properly rated, protected, and sized power circuit to avoid electrical overload.

Improper power circuits may melt, creating electric shock and/or fire hazard.

•• Remove all packing items and dispose of all shipping materials properly. Failure to do so may result in burns, fire, explosion, or death.

•• Place the dryer at least 18-inch above the floor for a garage installation. Failure to do so may result in burns, fire, explosion, or death.

•• Keep all packaging from children. Packaging material can be dangerous for children. There is a risk of suffocation.

•• Do not install near another heat source such as a stove, oven or heater. Failure to follow this warning may result in product deformation, smoke, or fire.

•• Do not place candles, smoking materials, or other flammables on top of the product. Dripping wax, smoke, or fire may result.

•• Remove all protective vinyl film from the product. Failure to do so may result in product damage, smoke, or fire.

•• Gas dryers MUST be exhausted to the outside.

Failure to follow these instructions may result in fire or death.

•• The dryer exhaust system must be exhausted to the outside of the dwelling. If the dryer is not exhausted outdoors, some fine lint and large amounts of moisture will be expelled into the laundry area. An accumulation of lint in any area of the home may create a health and fire hazard.

•• Use only rigid, semi-rigid or flexible metal 4-inch diameter duct inside the dryer cabinet or for exhausting to the outside. Use of plastic or other combustible ductwork may cause fire. Punctured ductwork may cause fire if it collapses or becomes otherwise restricted in use or during installation.

•• Ductwork is not provided with the dryer, and you should obtain the necessary ductwork locally. The end cap should have hinged dampers to prevent backdraft when the dryer is not in use. Failure to follow these instructions may result in fire or death.

•• The exhaust duct must be 4-inch (10.2 cm) in diameter with no obstructions. The exhaust duct should be kept as short as possible. Make sure to clean any old ducts before installing your new dryer. Failure to follow these instructions may result in fire or death.

•• Rigid, semi-rigid or flexible metal ducting is recommended for use between the dryer and the wall. All non-rigid metal transition duct must be UL-listed. Use of other materials for transition duct could affect drying time. Failure to follow these instructions may result in fire or death.

•• Do not use sheet metal screws or other fasteners which extend into the duct that could catch lint and reduce the efficiency of the exhaust system. Secure all joints with duct tape. For complete details, follow the Installation Instructions. Failure to follow these instructions may result in fire or death.

<![if ! IE]>

<![endif]>ENGLISH

6 SAFETY INSTRUCTIONS

Operation

•• Read all instructions before using the appliance.

•• Do not dry articles that have been previously cleaned in, washed in, soaked in, or spotted with gasoline, dry-cleaning solvents, or other flammable or explosive substances, as they give off vapors that could ignite or explode.

•• Do not reach into the appliance if the drum is moving.

•• Do not allow children to play on or in the appliance. Close supervision of children is necessary when the appliance is used near children.

•• Do not use fabric softeners or products to eliminate static unless recommended by the manufacturer of the fabric softener or product.

•• Do not use heat to dry articles containing foam rubber or similarly textured rubber-like materials.

•• Do not tamper with controls.

•• Always check the inside of the dryer for foreign objects. Failure to follow these instructions may result in fire or death.

•• Do not store plastic, paper, or clothing that may burn or melt on top of the dryer during operation. Failure to follow these instructions may result in fire or death.

•• Be careful when opening and closing the door. Fingers and hands can get caught in the door and cause injury if the door drops forward unexpectedly.

•• Do not place heavy items on or lean against the top of the door when it is open.

•• Do not attempt to pull the hamper door open more than 40 degrees.

•• The dryer could tip forward, causing injury or damage.

•• Do not place items on the top of the dryer.

•• Gas appliances can cause minor exposure to four of these substances, namely benzene, carbon monoxide, formaldehyde, and soot, caused primarily by the incomplete combustion of natural gas or LP fuels.

•• Properly adjusted dryers will minimize incomplete combustion. Exposure to these substances can be minimized further by properly venting the dryer to the outdoors.

Steam (steam model):

•• Do not open the dryer door during steam cycles. Failure to follow these instructions may result in a burn hazard.

•• Do not dry articles that have been previously cleaned in, washed in, soaked in, or spotted with gasoline, dry-cleaning solvents, or other flammable or explosive substances as they give off vapors that could ignite or explode. Failure to follow these instructions may result in fire or death.

•• Do not fill the steam feeder with gasoline, dry cleaning solvents, or other flammable or explosive substances. Failure to follow these instructions may result in fire or death.

•• Do not touch the steam nozzle in the drum during or after the steam cycles. Failure to follow these instructions may result in a burn hazard.

•• Do not fill the steam feeder with hot water (over 86 °F/30 °C). Failure to follow these instructions may result in a burn hazard.

Maintenance

•• Do not repair or replace any part of the appliance or attempt any servicing unless specifically recommended in the user maintenance instructions or in published user-repair instructions that you understand and have the skills to carry out.

•• Clean the lint filter before or after each load.

•• The interior of the appliance and exhaust duct should be cleaned periodically by qualified service personnel.

•• Before the appliance is removed from service or discarded, remove the door to the drying compartment.

Warning

Fire Hazard

Failure to follow safety warnings exactly could result in serious injury, death or property damage.

Do not install a booster fan in the exhaust duct.

Install all clothes dryers in accordance with the installation instructions of the manufacturer of the dryer.

SAVE THESE INSTRUCTIONS

SAFETY INSTRUCTIONS 7

GROUNDING INSTRUCTIONS

Warning

Improper connection of the equipment-grounding conductor may result in a risk of electric shock. Check with a qualified electrician or service person if you are in doubt that the appliance is properly grounded.

•• This appliance must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current.

•• This appliance must be equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

•• Do not modify the plug. If it will not fit the outlet, have a proper outlet installed by a qualified electrician.

•• This appliance must be connected to a grounded metal, permanent wiring system or an equipment-grounding conductor must be run with the circuit conductors and connected to the equipment-grounding terminal or lead on the appliance. Electric shock may result if the dryer is not properly grounded.

•• The dryer should always be plugged into its own individual electrical outlet which has a voltage rating that matches the rating plate. This provides the best performance and also prevents overloading house wiring circuits which can cause a fire hazard from overheated wires.

•• Never unplug your dryer by pulling on the power cord. Always grip the plug firmly and pull straight out from the outlet. The power cord may be damaged, resulting in a risk of fire and electric shock.

•• Repair or replace immediately all power cords that have become frayed or otherwise

damaged. Do not use a cord that shows cracks or abrasion damage along its length or at either end. The power cord may melt, creating electric shock and/or fire hazard.

•• When installing or moving the dryer, be careful not to pinch, crush, or damage the power cord.

This will prevent injury and damage to the dryer from fire and electric shock.

•• Do not, under any circumstances, cut or remove the ground prong from the power cord.

To prevent personal injury or damage to the dryer, the electrical power cord must be plugged into a properly grounded outlet.

•• For personal safety, this dryer must be properly grounded. Failure to do so may result in electric shock or injury.

•• Refer to the installation instructions in this manual for specific electrical requirements for your model. Failure to follow these instructions may create an electric shock hazard and/or a fire hazard.

•• This dryer must be plugged into a properly grounded outlet. Electrical shock may result if the dryer is not properly grounded. Have the wall outlet and circuit checked by a qualified electrician to make sure the outlet is properly grounded. Failure to follow these instructions may create an electric shock hazard and/or a fire hazard.

<![if ! IE]>

<![endif]>ENGLISH

8 PRODUCT OVERVIEW

PRODUCT OVERVIEW

Parts

	Reversible
Control	door	Terminal block
panel		access panel
		(electric models)

Power cord

location

(gas models)

	Lint filter		Water inlet valve
		Gas connection	(on some models)
	Leveling	location
		(gas models)	Exhaust duct
	feet
			outlet

Accessories	Two-Way Reversible Door
	(on some models)
Included Accessories

Y connector	Hoses	Drying rack Safety Tether
(steam models)	(steam	Kit
	models)	(on some
		models)

Optional accessories

Side vent kit	Pedestal or Pedestal Washer
(sold separately)
Kit No. 383EEL9001B	(sold separately)

Release

Hamper

door

Swing door

The LG EasyLoad™ feature allows you to open the dryer door from the top, hamper-style, when

loading the dryer to help guide clothes into the drum and prevent them from falling onto the floor. When unloading the dryer or loading bulkier items, use the swing door for easy access to the drum.

Safety Tether Kit (on some models)

This optional kit helps prevent the dryer tipping if children climb on the door or if someone should fall onto the door. It is recommended that you install this kit, depending on your situation, but it is not required. Follow the customer installation instructions included with the kit to properly install the kit. If you do not install the kit, store it out of reach of children.

NOTE

•• For your safety and for extended product life, use only authorized components. The manufacturer is not responsible for product malfunction or accidents caused by the use of separately purchased unauthorized components or parts.

•• The images in this guide may be different from the actual components and accessories, which are subject to change by the manufacturer without prior notice for product improvement purposes.

INSTALLATION 9

INSTALLATION

Installation Overview

Please read the following installation instructions first after purchasing this product or transporting it to another location.

<![if ! IE]>

<![endif]>ENGLISH

Check and choose	Level the dryer	Vent the dryer
the proper location

Connect the inlet hose	Connect gas dryers	Connect electric dryers
(steam models)

Gas dryer	Electric dryer
Plug in the power cord		Installation test	Test run

Product Specifications

The appearance and specifications listed in this manual may vary due to constant product improvements.

	Dryer Models	DLEY1701*E, DLGY1702*E	DLEY1701*, DLGY1702*
	Description	Steam Dryer
	Electrical requirements	Please refer to the rating label regarding detailed information.
	Gas requirements	NG: 4–10.5-inch WC
		LP: 8–13-inch WC
	Max. water pressure	20–120 psi (138–827 kPa)
	Dimensions	27” (W) X 28 15/16” (D) X 40 3/16” (H), 50 1/4” (D with door open)
		68.6 cm (W) X 73.4 cm (D) X 102 cm (H), 127.5 cm (D with door open)
	Net weight	Gas dryer : 136 lb (61.7 kg) –138 lb (62.6 kg)
		Electric dryer : 133.5 lb (60.6 kg) –134.5 lb (61.0 kg)
	Drying capacity
	- Normal cycle	IEC 7.3 cu.ft. (22.5 lb/10.2 kg)

10 INSTALLATION

Installation Location Requirements

Warning

Read all installation instructions completely before installing and operating your dryer! It is important that you review this entire manual before installing and using your dryer. Detailed instructions concerning electrical connections, gas connections, and exhaust requirements are provided on the following pages.

The installation requires:

•• A location that allows for proper exhaust installation. A gas dryer must be exhausted to the outdoors. See Venting the Dryer.

•• A grounded electrical outlet located within 2 ft. (61 cm) of either side of the dryer. See Connecting Electric Dryers .

•• A sturdy floor to support the total dryer weight of 200 lb (90.7 kg). The combined weight of a companion appliance should also be considered.

•• No other fuel-burning appliance can be installed in the same closet as a dryer.

Do not operate your dryer at temperatures below 45 °F (7 °C). At lower temperatures, the dryer might not shut off at the end of an automatic cycle. This can result in longer drying times. The dryer must not be installed or stored in an area where it will be exposed to water and/or weather. Check code requirements. Some codes limit, or do not permit, installation of the dryer in garages, closets, mobile homes or sleeping quarters. Contact your local building inspector.

NOTE

•• The floor must be level, with a maximum slope of 1 inch (2.5 cm) under the entire dryer. Clothes may not tumble properly, and automatic sensor cycles may not operate correctly if dryer is not level.

•• For a garage installation, you will need to place the dryer at least 18-inch (46 cm) above the floor. The standard pedestal is 15-inch. You will need 18-inch (46 cm) from the garage floor to the bottom of the dryer.

Clearances

Installation Spacing for Recessed Area or Closet Installation

The following spacing dimensions are recommended for this dryer. This dryer has been tested for clearances of 1 inch (2.5 cm) on the sides and rear. Recommended clearances should be considered for the following reasons:

•• Additional clearances should be considered for ease of installation and servicing.

•• Additional clearances might be required for wall, door and floor moldings.

•• Additional clearances should be considered on all sides of the dryer to reduce noise transfer.

For closet installation, with a door, minimum ventilation openings in the top and bottom of the door are required. Louvered doors with equivalent ventilation openings are acceptable.

•• Companion appliance spacing should also be considered.

INSTALLATION 11

Closet Ventilation Requirements

Closets with doors must have both an upper and lower vent to prevent heat and moisture buildup in the closet. One upper vent opening with a minimum opening of 48 sq. in. (310 cm2) must be installed no lower than 6 feet above the floor. One lower vent opening with a minimum opening of 24 sq. in. (155 cm2) must be installed no more than one foot above the floor. Install vent grills in the door or cut down the door at the top and bottom to form openings. Louvered doors with equivalent ventilation openings are also acceptable.

NOTE

There should be at least a little space around the dryer (or any other appliance) to eliminate the transfer of vibration from one appliance to another. If there is enough vibration, it could cause appliances to make noise or come into contact, causing paint damage and further increasing noise.

<![if ! IE]>

<![endif]>ENGLISH

Installation Spacing for Recessed Area or Closet

3"
(7.6 cm)
				14" max.*
		21 1/4"		(35.6 cm)
				18" min.
48 in.2		(54 cm)
				(45.7 cm)
(310 cm2)
24 in.2
(155 cm2)
				28 15/16"	5"**
	Closet Door Vent				(12.7 cm)
3"		50	1/4"	(73.4 cm)
	Requirements
(7.6 cm)		(127.5 cm)

*Required spacing

**For side or bottom venting, 2-inch (5.1 cm) of spacing is allowed

1"

27"

1"

(2.5 cm)

(68.6 cm)

(2.5 cm)

Installation Spacing for Cabinet

For cabinet installation with a door, minimum ventilation openings in the top of the cabinet are required.

* Required spacing

7"* (17.8 cm) 7"* (17.8 cm)

			1"		1"
5"*	28 15/16"	1"*	(2.5 cm)	27"	(2.5 cm)
(12.7 cm)	(73.4 cm)	(2.5 cm)		(68.6 cn)

Installing on a pedestal

								5"
			2815/16"
		(73.4 cm)						(12.7 cm)

NOTE

Refer to the instructions packaged with the optional PEDESTAL before installing with a PEDESTAL.

12 INSTALLATION

Leveling the Dryer

Warning

To reduce the risk of injury to persons, adhere to all industry recommended safety procedures including the use of long-sleeved gloves and

safety glasses. Failure to follow this warning may result in serious injury or death.

•• The appliance is heavy. Two or more people are required when installing the dryer. Failure to follow this warning may result in serious injury or death.

•• To ensure that the dryer provides optimal drying performance, it must be level. To minimize vibration, noise, and unwanted movement, the floor must be a perfectly level, solid surface.

NOTE

Adjust the leveling feet only as far as necessary to level the dryer. Extending the leveling feet more than necessary may cause the dryer to vibrate.

1 Position the dryer in the final location. Check levelness of dryer from side to side. Repeat from front to back

Place level here

Place level here

2 Use an adjustable wrench to turn the leveling feet. Unscrew the legs to raise the dryer or screw in the legs to lower it. Raise or lower with the leveling feet until the dryer is level from side to side and front to back. Make sure that all four leveling feet are in firm contact with the floor.

•• All four leveling feet must rest solidly on the floor. Gently push on the top corners of the dryer to make sure that the dryer does not rock from corner to corner.

If you are installing the dryer on the optional pedestal, you must use the leveling feet on the pedestal to level the dryer. The dryer leveling feet should be fully retracted.

Reversing the Door

Before you Begin

NOTE

Service calls to reverse the door are not covered under the product warranty.

•• The door reversal process for the two-way door is more complex than for a conventional dryer door. Read through these instructions in their entirety before beginning the process, in order to gauge whether to have the procedure done by a professional installer or service person.

•• A support video is also provided at http://www. lg.com/us/support/videos/video-tutorials-view, How to Reverse the Door – LG EasyLoad™ Dryer.

Not Level

Level

Not Level

INSTALLATION 13

Tools Required

•• Phillips screwdriver

•• Large flat blade screwdriver (recommended for hinge screws if they are tight or your Phillips screwdriver is worn)

•• Small flat blade screwdriver (for lifting out parts)

Warning

THE DRYER DOOR IS VERY LARGE AND HEAVY. Failure to follow the instructions below may result in damage to the dryer, property damage or personal injury.

•• To avoid damage to the dryer or the door, support the door with a stool or box that fits under the door, or have an assistant support the weight of the door.

•• Avoid dropping the door to avoid damage to the door or the floor.

•• Unplug the dryer or turn off power at the main circuit breaker before beginning door reversal.

Swing door

1	Open the door and remove the two plastic hole
	caps on the catch side by gently prying up with a

flat blade screwdriver. Save these for step 6.

Hole cap

2 While supporting the door, remove the 4 screws, two from each hinge. Set the door aside face down on a protected surface to prevent damage to the door or the work surface.

Hinge screw

<![if ! IE]>

<![endif]>ENGLISH

Door Reversal Instructions

NOTE

The instructions here are for changing the door swing from a right to a left side hinge. If the door has been reversed, and it is necessary to change it back, use care when following these

instructions. Some of the illustrations and the left/ right references will be reversed, and you will need to read the instructions carefully.

Warning

Be sure to support the weight of the door before removing the hinge screws.

Warning

The edges of the door cover may be sharp. Take care when handling, or wear gloves to avoid injury.

3 With the door on a protected surface, remove the 16 screws on each side of the door and lift off the inner door frame using a flat blade screwdriver. Remove the latch hook and blank and install them on the opposite side.

Inner door

frame

Blank Latch hook

4 Remove the 4 screws securing the hinges to the door frame. Remove the two plastic cover caps. Reinstall the hinges and cover caps on the opposite sides from which they were removed.

Hinge assembly

Cover cap

14 INSTALLATION

5 With the hinges and cover caps in the new locations, remount the inner door frame onto the outer door frame with the screws removed in step 3 above.

Warning

Be sure to support the weight of the door before installing the hinge screws.

6	Reinstall the door with the screws removed in
	step 2. Install the two plastic hole caps removed

in step 1 on the opposite side.

Hamper door (on some models)

The door reversal procedure consists of four main parts:

•• Removing and reinstalling the door and hinges (steps 1, 2, and 20)

•• Removing and reversing components on the dryer cabinet (step 3)

•• Removing and reversing components on the door cover (steps 4 and 5)

•• Removing and reversing components inside the door (steps 6 through 19)

1	Open the door from the side so that the hinge
	screws are accessible.

Two large screws

2 Remove the four hinge screws

While supporting the door, remove the four hinge screws, two from each hinge. Set the door aside face down on a protected surface to prevent damage to the door or the work surface.

3 Reverse the components on the cabinet.

a.Use a Phillips screwdriver to remove the two screws and the latch mechanism on the front panel of the cabinet.

Hinge	Upper
cover	hinge
latch	Latch
mechanism	hole
	cover
Hinge	Hinge
	bracket

b.Remove the latch hole cover by gently prying it up with a flat blade screwdriver, being careful not to scratch the paint. Install the latch hole cover on the opposite side, where the latch mechanism was removed. Install the latch mechanism in the position from which you removed the latch hole cover, using the two screws removed in step a.

c.Remove the hinge cover by gently prying it up with a flat blade screwdriver, being careful not to scratch the paint. Rotate the hinge cover 180 degrees and install it on the opposite side, where the upper hinge was attached.

Hinge	Upper
cover	hinge
latch	Latch
mechanism	hole
	cover
Hinge	Hinge
	bracket

d.Reverse the hinge and the hinge bracket at the bottom of the cabinet. Remove the two screws from the hinge bracket at the bottom right and remove the hinge bracket. Remove the lower of the two screws behind the hinge bracket. Do NOT remove the upper screw behind the hinge bracket. Set the parts aside.

Two small screws

INSTALLATION 15

CAUTION

Do NOT remove any of the eight screws on the face of the cabinet (marked below). Doing so could result in damage to the dryer and the need for a service call to repair the dryer.

5 Switch the door strike and the blank cover.

Remove the four screws on the door cover that secure the door strike and the blank cover.

Switch the door strike and the blank cover, installing them on the opposite sides from which they were removed.

<![if ! IE]>

<![endif]>ENGLISH

e.Remove the three screws on the hinge at the bottom left. Remove the hinge and reinstall it on the right side. The top screw will occupy the hole where you removed the screw behind the hinge bracket in step d.

f.Install the hinge bracket removed in step d on the bottom left side, first installing one screw behind the hinge bracket.

ON THE DOOR:

4 Lift off the door cover.

With the door laid inside facing up on a protected surface, remove the twelve screws on the inside of the door. Carefully lift off the door cover with the help of a small flat blade screwdriver inserted in the upper corner (circled below).

Warning

The edges of the door cover may be sharp. Take care when handling, or wear gloves to avoid injury.

Twelve screws

Long	Short	Long
screw	screws	screw

Blank cover

Door strike

Gently pry out the hole plug on the side of the door cover and install it in the hole on the opposite side.

Hole plug

Set the door cover aside.

Hole	Interlock
plug	button

16		INSTALLATION
6	Reverse the components inside the door.
	You will now be removing and reversing various components inside the door. See below for a detailed
	diagram and identification of the inner structure and parts of the door. (The diagram shows the “before view”
	of the door, with the default set-up for a right side hinge swing. After following these instructions, your door
	should be a mirror image of the illustration.)
		Top interlock buttons	Inner lock rods

Upper hinge assembly

	Upper	Upper
		hinge filter
	hinge pivot

Top lock rod

Side lock rod

Glass

Side Interlock button

Lower	Lower
hinge
assembly	hinge filler
	Lower
	hinge
	bracket
	Bumpers

Interlock buttons			Low hinge filler	Side lock rod						Top lock rod

Inner lock rods

Lower hinge bracket

Hole plug

Lower hinge assembly

INSTALLATION 17

7 Lift out the two top interlock buttons.

Lift out the two grey interlock buttons from the top of the outer door and set them aside for later use.

Side lock rod

Interlock buttons

8 Lift out the grey interlock button in the side of the door.

Make sure to remove the spring with the interlock button and to keep the two together. Set the interlock button aside. Do not confuse these with the interlock buttons from the top of the outer door.

9 Remove the side lock rod.

Remove the side lock rod from the lower hinge bracket by lifting the top end of the rod and sliding it toward the top of the door. The spring should remain attached to the lock rod. Set the lock rod aside.

Spring

10 Remove the top lock rod.

a.Slide the lock rod to the right to remove it from the hinge assembly on the left side.

b.While sliding the lock rod right, lift the right end up and out of the guides.

NOTE

Do not remove the two inner lock rods (see page 16) located underneath the top lock rod. They do NOT need to be reversed.

11 Remove the upper hinge pivot.

Once the top lock rod has been removed, the hinge pivot can easily be removed from the hinge assembly on the upper left and set aside.

Upper hinge assembly

Upper hinge pivot

12 Reverse the upper hinge assembly and hinge filler.

Lift out the upper hinge filler (on the right) and set it aside.

Carefully lift the upper hinge assembly (on the left) out of the outer door frame, using a small flat blade screwdriver if necessary. Rotate the hinge assembly 180 degrees and install it on the upper right side of the outer door. You will need to press firmly to install the hinge assembly.

The hinge pivot removed in step 11 will be installed later.

Upper hinge assembly

Upper hinge pivot

Now rotate the hinge filler 180 degrees and install it on the upper left side of the door.

<![if ! IE]>

<![endif]>ENGLISH

Upper hinge filler

18 INSTALLATION

13 Reinstall the top lock rod.

Rotate the top lock rod (removed in step 10) 180 degrees end for end from its original position and reinstall it. The spring should now be to the right of center, with the spring on the side of the rod facing the top of the door.

a.Insert the right end of the lock rod into the right hinge assembly. Make sure the rod is aligned with the guides in the door panel.

c.Flip over the lower hinge bracket and release the tabs on the back locking the hinge filler to the hinge bracket.

Tab

d.Rotate the hinge 180 degrees and snap it back onto the front of the hinge bracket facing in the opposite direction.

b.Lower the rod into position, sliding it to bypass the center handle, making sure to align the lock rod with the guides all the way across the door panel. When released, the lock rod should slide completely into the hinge assembly on the right. Slide the lock rod back and forth to make sure it is correctly positioned in the guides and slides easily.

14	Reverse the lower hinge bracket and hinge
	assembly.

a.Remove the screw from the lower hinge bracket (on the right) and lift the hinge bracket out. Set it aside. Remove the two screws from the lower hinge assembly on the bottom left and lift the hinge assembly out.

e.Mount the lower hinge bracket and the filler on the left side of the door with the screw removed in step a.

Screw

15 Install the side lock rod.

Flip the side lock rod over and install it on the opposite side. Insert the lower end into the left hinge and lower the rod into the guides on the door while compressing the spring inside the recess.

b.Rotate the lower hinge assembly 180 degrees and install it on the right side using the two screws removed in step a.

Screws

Lower hinge assembly

Make sure the top of the side lock rod is beside the top lock rod and the two do not overlap each other, so the two rods can interact correctly. If they are not aligned properly, the door will not operate properly.

INSTALLATION 19

16 Reinstall the top interlock buttons.

Reinstall the top gray interlock buttons removed in step 7, one on each side of the outer door panel.

17 Reinstall the side interlock button.

Reinstall the side interlock button removed in step 8. Center the spring in the compartment and insert the interlock button on top of it.

19 Now, pick up the upper hinge pivot removed earlier and rotate it 180 degrees.

Press in the side interlock button on the left side and hold it down while you press the hinge pivot into the hinge assembly on the top right side. If the door has been reassembled correctly, the lock rod will slide back easily and lock the pivot in place. The door is now ready to remount on the opposite side of the dryer.

<![if ! IE]>

<![endif]>ENGLISH

18 Reinstall the door cover.

Clean the glass on the door and door cover, if necessary.

Make sure the three gray interlock buttons are properly installed and that the top and side lock rods are properly aligned where they meet. Carefully lower the door cover into place, aligning the holes in the cover with the interlock buttons on the top and side and the bumpers on the bottom. Take care not to

dislodge the lock rods while mounting the door cover. Once the door cover is in place, secure it with the 12 screws removed in step 4. The ten similar screws go around the top and sides of the door cover. Make sure to install the two different screws on the bottom edge, in the locations marked below.

Interlock

buttons

Bumpers

Warning

Be sure to support the weight of the door before installing the hinge screws.

20 Reinstall the door.

While supporting the door, install the four hinge screws removed in step 2. Test the swing of the door to make sure the hinges and latch are properly aligned and that the door opens, closes and latches properly in both directions.

Two large screws

Two small screws

20 INSTALLATION

Installing the Side Vent Kit

Warning

•• Use a heavy metal vent.

•• Do not use plastic or thin foil ducts.

•• Clean old ducts before installing this dryer.

•• To reduce the risk of injury to persons, adhere to all industry recommended safety procedures including the use of long-sleeved gloves and safety glasses.

•• Failure to follow all of the safety warnings in this manual could result in property damage, injury to persons, or death.

Your new dryer is shipped to vent to the rear. It can also be configured to vent to the bottom or side (rightside venting is not available on gas models).

An adapter kit, part number 383EEL9001B, may be purchased from your LG retailer. This kit contains the necessary duct components to change the dryer vent location.

1	Remove the rear exhaust duct retaining screw.
	Pull out the exhaust duct.

Retaining Screw

	Rear Exhaust
	Duct
Option 1: Side Venting
2	Press the tabs on the knockout and carefully
	remove the knockout for the desired vent
	opening (right-side venting is not available on
	gas models). Press the adapter duct onto the
	blower housing and secure to the base of the
	dryer as shown.
	Adapter
	Duct

Bracket

Knockout

3 Preassemble a 4-inch (10.2 cm) elbow to the next 4-inch (10.2 cm) duct section, and secure all joints with duct tape. Be sure that the male end of the elbow faces AWAY from the dryer. Insert the elbow/duct assembly through the side opening and press it onto the adapter duct. Secure it in place with duct tape. Be sure that the male end of the duct protrudes 1½-inch (3.8 cm) to connect the remaining ductwork. Attach the cover plate to the back of the dryer with the included screw.

Cover
Plate
Elbow	1½"
	(3.8 cm)

Option 2: Bottom Venting

2	Press the adapter duct onto the blower housing
	and secure it to the base of the dryer as shown.
	Adapter
	Duct

	Bracket
3	Insert the 4-inch (10.2 cm) elbow through the
	rear opening and press it onto the adapter duct.

Be sure that the male end of the elbow faces down through the hole in the bottom of the dryer. Secure it in place with duct tape. Attach the cover plate to the back of the dryer with the included screw.

Cover

Plate

Elbow

INSTALLATION 21

Venting the Dryer

Warning

To reduce the risk of fire or explosion, electric shock, property damage, injury to persons or death when using this appliance, follow basic safety precautions, including the following:

•• Do not crush or collapse ductwork. Failure to follow these instructions may result in fire or death.

•• Do not allow ductwork to rest on or contact sharp objects. Failure to follow these instructions may result in fire or death.

•• If connecting to existing ductwork, make sure it is suitable and clean before installing the dryer.

Failure to follow these instructions may result in fire or death.

•• Venting must conform to local building codes.

Failure to follow these instructions may result in fire or death.

•• Gas dryers MUST exhaust to the outdoors.

Failure to follow these instructions may result in fire or death.

•• Use only 4-inch (10.2 cm) rigid, semi-rigid or flexible metal ductwork inside the dryer cabinet and for venting outside. Failure to follow these instructions may result in fire or death.

•• To reduce the risk of fire, combustion, or accumulation of combustible gases, DO NOT exhaust dryer air into an enclosed and

unventilated area, such as an attic, wall, ceiling, crawl space, chimney, gas vent, or concealed space of a building. Failure to follow these instructions may result in fire or death.

•• To reduce the risk of fire, DO NOT exhaust the dryer with plastic or thin foil ducting. Failure to follow these instructions may result in fire or death.

•• The exhaust duct must be 4-inch (10.2 cm) in diameter with no obstructions. The exhaust duct should be kept as short as possible. Make sure to clean any old ducts before installing your new dryer. Failure to follow these instructions may result in fire or death.

•• Rigid, semi-rigid or flexible metal ducting is recommended for use between the dryer and the wall. All non-rigid metal transition duct must be UL-listed. Use of other materials for transition duct could affect drying time. Failure to follow these instructions may result in fire or death.

•• DO NOT use sheet metal screws or other fasteners which extend into the duct that could catch lint and reduce the efficiency of the exhaust system. Secure all joints with duct tape. Failure to follow these instructions may result in fire or death.

•• Do not exceed the recommended duct length limitations noted in the chart. Failure to follow these instructions may result in extended drying times, fire or death.

•• Ductwork is not provided with the dryer. You should obtain the necessary ductwork locally. The vent hood should have hinged dampers to prevent backdraft when the dryer is not in use.

Failure to follow these instructions may result in fire or death.

•• The total length of flexible metal duct must not exceed 8 ft. (2.4 m).

•• In Canada, only those foil-type flexible ducts, if any, specifically identified for use with the appliance by the manufacturer should be used.

In the United States, only those foil-type flexible ducts, if any, specifically identified for use with the appliance by the manufacturer and that comply with the Outline for Clothes Dryer Transition Duct, Subject 2158A, should be used.

Ductwork

		Number	Maximum
			length of 4-inch
	Wall Cap Type	of 90°
			diameter rigid
		Elbows
			metal duct
	Recommended	0	65 ft.(19.8 m)
		1	55 ft.(16.8 m)
	4"	2	47 ft.(14.3 m)
	(10.2 cm)
	4"	3	36 ft.(11.0 m)
	(10.2 cm)	4	28 ft.(8.5 m)
	Use only for	0	55 ft.(16.8 m)
	short run	1	47 ft.(14.3 m)
	installations	2	41 ft.(12.5 m)
	21/2"	3	30 ft.(9.1 m)
	(6.35 cm)	4	22 ft.(6.7 m)

NOTE

Deduct 6 ft. (1.8 m) for each additional elbow. Do not use more than four 90° elbows.

<![if ! IE]>

<![endif]>ENGLISH

22 INSTALLATION

Routing And Connecting Ductwork

NOTE

Follow the guidelines below to maximize drying performance and reduce lint buildup and condensation in the ductwork. Ductwork and fittings are NOT included and must be purchased separately.

•• Use 4-inch (10.2 cm) diameter rigid, semi-rigid or flexible metal ductwork.

•• The exhaust duct run should be as short as possible.

•• Use as few elbow joints as possible.

•• The male end of each section of exhaust duct must point away from the dryer.

•• Use duct tape on all duct joints.

•• Insulate ductwork that runs through unheated areas in order to reduce condensation and lint buildup on duct surfaces.

•• Incorrect or inadequate exhaust systems are not covered by the dryer warranty. Dryer failures or service required because of such exhaust systems will not be covered by the dryer warranty.

Correct Venting

Incorrect Venting

INSTALLATION 23

Connecting the Inlet Hose (Steam Models)

The dryer must be connected to the cold water tap using a new water supply hose. Do not use old hoses.

NOTE

•• Water supply pressure must be between 20 and 120 psi (138—827 kPa) .

•• Do not strip or cross-thread when connecting the inlet hose to the valve.

•• If the water supply pressure is more than 800 kPa, a pressure-reducing valve should be installed.

•• Periodically check the condition of the hose and replace the hose if necessary.

•• Replace inlet hoses after 5 years of use to reduce the risk of hose failure.

•• Record hose installation or replacement dates on the hoses for future reference.

1	Check the rubber seal at each end of the inlet
	hoses. Two rubber seals are supplied with each
	inlet hose. They are used for preventing water
	leaks. Make sure the connection to the cold
	water tap is tight.
	Hose
	connector
	Rubber
	seal
	Y connector
2 Check the installation type.

d.Connect the long dryer hose to one side of the Y-connector and connect the washer hose to the other side.

WITHOUT WASHER: If the dryer does not share the cold water tap with a washer.

a.Connect the straight end of the long hose to the cold water faucet.

NOTE

•• Before connecting the water line to the dryer, flush several gallons of water into a drain or bucket. This will help prevent foreign particles such as sand and scale from clogging the dryer inlet valve.

•• Do not overtighten. Damage to the coupling may result.

3 Connect the hose to the dryer. Connect the water supply hose to the dryer inlet valve tightly by hand and then tighten another 2/3 turn with pliers.

Make sure that there are no kinks in the hoses and that they are not crushed.

4 Turn on the cold water faucet.

	Short	Long
	hose	hose
	Y connector		5	Check for leaks at the Y-connector (if used) and
	WITH WASHER	WITHOUT WASHER
				in all hoses.

Connect all water supply hoses tightly by hand and then tighten another 2/3 turn with pliers.

WITH WASHER: When connecting the dryer to the same faucet as a washer.

a.Shut off the cold water tap and remove the washer hose.

b.Connect the short hose to the Y-connector using one of the rubber seals.

c.Connect the other end of the short hose to the cold water faucet.

NOTE

•• If any leaks are found, shut off the water faucet, remove the hose and check the condition of the rubber seal.

<![if ! IE]>

<![endif]>ENGLISH

24 INSTALLATION

Connecting Gas Dryers

Warning

To reduce the risk of fire or explosion, electric shock, property damage, injury to persons, or death when using this appliance, follow basic safety precautions.

Gas Supply Requirements

•• As shipped from the factory, this dryer is configured for use with natural gas (NG). It can be converted for use with propane (LP) gas. Gas pressure must not exceed 8-inch water column for NG, or 13-inch water column for LP.

•• A qualified service or gas company technician must connect the dryer to the gas service. Failure to follow these instructions may result in fire, explosion, or death.

•• Isolate the dryer from the gas supply system by closing its individual manual shutoff valve during any pressure testing of the gas supply.

Failure to do so may result in fire, explosion, or death.

•• Supply line requirements: Your laundry room must have a rigid gas supply line to your dryer. In the United States, an individual manual shutoff valve MUST be installed within at least 6 ft. (1.8 m) of the dryer, in accordance with the National Fuel Gas Code ANSI Z223.1 or Canadian gas installation code CSA B149.1. A

1/8-inch NPT pipe plug must be installed. Failure to do so may result in fire, explosion, or death.

•• If using a rigid pipe, the rigid pipe should be ½ inch IPS. If acceptable under local codes and ordinances and when acceptable to your gas supplier, 3/8-inch approved tubing may be used where lengths are less than 20 ft. (6.1 m). Larger tubing should be used for lengths in excess of 20 ft. (6.1 m). Failure to do so may result in fire, explosion, or death.

•• Connect the dryer to the type of gas shown on the nameplate. Failure to do so may result in fire, explosion, or death.

•• To prevent contamination of the gas valve, purge the gas supply of air and sediment before connecting the gas supply to the dryer. Before tightening the connection between the gas supply and the dryer, purge remaining air until the odor of gas is detected. Failure to do so may result in fire, explosion, or death.

•• DO NOT use an open flame to inspect for gas leaks. Use a noncorrosive leak detection fluid.

Failure to do so may result in fire, explosion, or death.

•• Use only a new AGAor CSA-certified gas supply line with flexible stainless steel connectors. Failure to do so may result in fire, explosion, or death.

•• Securely tighten all gas connections. Failure to do so may result in fire, explosion, or death.

•• Use Teflon tape or a pipe-joint compound that is insoluble in propane (LP) gas on all pipe threads. Failure to do so may result in fire, explosion, or death.

•• DO NOT attempt any disassembly of the dryer; disassembly requires the attention and tools of an authorized and qualified service technician or company. Failure to follow this warning may result in fire, explosion, or death.

Electrical Requirements for Gas Models Only

•• Do not, under any circumstances, cut or remove the third (ground) prong from the power cord.

Failure to follow this warning may result in fire, explosion, or death.

•• For personal safety, this dryer must be properly grounded. Failure to follow this warning may result in fire, explosion, or death.

•• This dryer must be plugged into a 120-VAC, 60-

Hz. grounded outlet protected by a 15-ampere fuse or circuit breaker. Failure to follow this warning may result in fire, explosion, or death.

•• Where a standard 2-prong wall outlet is encountered, it is your personal responsibility and obligation to have it replaced with a properly grounded 3-prong wall outlet. Failure to follow this warning may result in fire, explosion, or death.

Plugdrdryerer intointoa a 120 VAC,

60 Hz grounded 3-prong outlet.

Warning

ELECTRIC SHOCK HAZARD

Failure to follow safety warnings could result in serious injury or death.

This dryer is equipped with a three-prong grounding plug for protection against shock hazard and should be plugged directly into a properly grounded three-prong receptacle. Do not cut or remove the grounding prong from this plug.

			INSTALLATION 25
	Connecting the Gas Supply	4	Securely tighten all connections between the
	•• Installation and service must be performed		dryer and your laundry room’s gas supply.
		5
	by a qualified installer, service agency, or the		Turn on your laundry room’s gas supply.
	gas supplier. Failure to do so may result in fire,
	explosion, or death.	6	Check all pipe connections (both internal and
	•• Use only a new stainless steel flexible
			external) for gas leaks with a noncorrosive leak-
	connector and a new AGA-certified connector.		detection fluid.
	Failure to do so may result in fire, explosion, or	7	Proceed to Venting the Dryer.
	death.
	•• A gas shutoff valve must be installed within 6 ft.
	(1.8 m) of the dryer. Failure to do so may result in
	fire, explosion, or death.

•• The dryer is configured for natural gas when shipped from the factory. Make sure that the dryer is equipped with the correct burner nozzle for the type of gas being used (natural gas or propane gas). Failure to do so may result in fire, explosion, or death.

•• If necessary, the correct nozzle (for the LP nozzle kit, order part number 383EEL3002D) should be installed by a qualified technician and the change should be noted on the dryer.

Failure to do so may result in fire, explosion, or death.

•• All connections must be in accordance with local codes and regulations. Failure to do so may result in fire, explosion, or death.

•• Gas dryers MUST exhaust to the outdoors.

Failure to do so may result in fire, explosion, or death.

3/8" NPT gas Connection

AGA/CSA-Certified

Stainless Steel Flexible Connector

1/8" NPT Pipe Plug

Gas Supply Shutoff

Valve

High-altitude Installations

The BTU rating of this dryer is AGA-certified for elevations below 10,000 feet.

If your gas dryer is being installed at an elevation above 10,000 feet, it must be derated by a qualified technician or gas supplier.

NOTE

This dryer is configured from the factory for natural gas (NG). If the dryer is to be used with propane (LP) gas, it must be converted by a qualified service technician.

1	Make sure that the gas supply to the laundry
	room is turned OFF and the dryer is unplugged.
	Confirm that the type of gas available in your
	laundry room is appropriate for the dryer.
2	Remove the shipping cap from the gas fitting at
	the back of the dryer. Be careful not to damage
	the threads of the gas connector when removing
	the shipping cap.
3	Connect the dryer to your laundry room’s gas

supply using a new flexible stainless steel connector with a 3/8-inch NPT fitting.

NOTE

DO NOT use old connectors.

<![if ! IE]>

<![endif]>ENGLISH

26 INSTALLATION

Connecting Electric Dryers

Electrical Requirements for Electric Models Only

Warning

To help prevent fire, electric shock, serious injury, or death, the wiring and grounding must conform to the latest edition of the National Electrical Code, ANSI/NFPA 70 and all applicable local regulations. Please contact a qualified electrician to check your home’s wiring and fuses to ensure that your home has adequate electrical power to operate the dryer.

•• This dryer must be connected to a grounded metal, permanent wiring system, or an equipment-grounding conductor must be run with the circuit conductors and connected to the equipment-grounding terminal or lead on the dryer. Failure to do so may result in fire, explosion, or death.

•• The dryer has its own terminal block that must be connected to a separate 240 VAC, 60-Hertz, single-phase circuit, fused at 30 amperes (the circuit must be fused on both sides of the line). ELECTRICAL SERVICE FOR THE DRYER

SHOULD BE OF THE MAXIMUM RATE VOLTAGE LISTED ON THE NAMEPLATE. DO NOT CONNECT THE DRYER TO 110-, 115-, OR 120VOLT CIRCUIT. Failure to follow these instructions may result in fire, explosion, or death.

•• If the branch circuit to dryer is 15 ft. (4.5 m) or less in length, use UL (Underwriters

Laboratories) listed No.-10 AWG wire (copper wire only), or as required by local codes. If over 15 ft. (4.5 m), use UL-listed No.-8 AWG wire (copper wire only), or as required by local codes. Allow sufficient slack in wiring so the dryer can be moved from its normal location when necessary. Failure to do so may result in fire, explosion, or death.

•• The power cord (pigtail) connection between the wall receptacle and the dryer terminal block IS NOT supplied with the dryer. Type of pigtail and gauge of wire must conform to local codes and with instructions on the following pages.

Failure to follow these instructions may result in fire, explosion, or death.

•• A 4-wire connection is required for all mobile and manufactured home installations, as well as all new construction after January 1, 1996. A 4-wire connection must be used where local codes do not permit grounding through the neutral wire. Failure to do so may result in fire, explosion, or death.

•• Do not modify the plug and internal wire provided with the dryer.

•• The dryer should be connected to a 4-hole outlet.

•• If the plug does not fit the outlet, a proper outlet will need to be installed by a qualified electrician.

Special Electrical Requirements for Mobile or Manufactured Homes

•• Any installation in a manufactured or mobile home must comply with the Manufactured Home Construction and Safety Standards Title 24 CFR, Part 3280 or Standard CAN/ CSA Z240 MH and local codes and ordinances. If you are uncertain whether your proposed installation will comply with these standards, please contact a service and installation professional for assistance.

•• A 4-wire connection is required for all mobile and manufactured home installations, as well as all new construction after January 1, 1996.

Failure to do so may result in fire, explosion, or death.

•• A gas dryer must be permanently attached to the floor.

•• The electrical connection for an electric dryer must be a 4-wire connection. More detailed information concerning the electrical connection is provided in the section Connecting Electric Dryers.

•• To reduce the risk of combustion and fire, the dryer must be vented to the outside.

•• DO NOT vent the dryer under a manufactured home or mobile home.

•• Electric dryers may be vented to the outside using the back, left, right, or bottom panel.

•• Gas dryers may be vented to the outside using the back, left, or bottom panel. Gas dryers may not be vented to the outside using the right side panel because of the burner housing.

•• The dryer exhaust duct must be affixed securely to the manufactured or mobile home structure, and the exhaust duct must be made of a material that will resist fire and combustion. It is recommended that you use a rigid, semi-rigid or flexible metal duct.

•• DO NOT connect the dryer exhaust duct to any other duct, vent, chimney, or other exhaust duct.

•• Make sure the dryer has adequate access to outside fresh air to ensure proper operation. The opening for outside fresh air must be at least 25 sq. in (163 cm2).

•• It is important that the clearance of the duct from any combustible construction be at least 2-inch

(5 cm), and when venting the dryer to the outdoors, the dryer should be installed with a clearance of at least 1 inch (2.5 cm) at the sides and back of the dryer.

•• Please be aware that venting materials are not supplied with the dryer. You must obtain the venting materials necessary for proper installation.

INSTALLATION 27

Warning

Connect the power cord to the terminal block. Each colored wire should be connected to the same color screw. Wire color indicated on manual is connected to the same color screw in the block. Failure to follow these instructions may result in a short or overload.

Grounding through the neutral conductor is prohibited for: (1) new branch-circuit installations,

(2) mobile homes, (3) recreational vehicles, and

(4) areas where local codes prohibit grounding through the neutral conductor.

Four-Wire Power Cord

•• A 4-wire connection is required for all mobile and manufactured home installations, as well as all new construction after January 1, 1996.

•• A UL-listed strain relief is required.

•• Use a 30-amp, 240-volt, 4-wire, UL-listed power cord with #10 AWG-minimum copper conductor and closed loop or forked terminals with upturned ends.

1	Remove the terminal block access cover on the
	upper back of the dryer.
2	Install a UL-listed strain relief into the power cord
	through-hole.
3	Thread a 30-amp, 240-volt, 4-wire, UL-listed
	power cord with #10 AWG-minimum copper
	conductor through the strain relief.

Terminal Block

UL-Listed

Strain Relief

UL-Listed 4-Wire Power Cord

4 Transfer the dryer’s ground wire from behind the green ground screw to the center screw of the terminal block.

NOTE

5	Attach the two hot leads of the power cord to the
	outer terminal block screws.
6	Attach the white neutral wire to the center screw
	of the terminal block.
7	Attach the power cord ground wire to the green
	ground screw.
8	Tighten all screws securely.
9	Reinstall the terminal block access cover.
	Hot	Neutral
	(Black)	(White)
		Hot
	Ground	(Red)
	Screw	White Wire
		moved from
		Ground
	Power Cord	Screw
	Ground Wire

This dryer is supplied with the neutral wire grounded. This white ground wire MUST BE MOVED to the neutral terminal when a 4-wire cord is to be used, or where grounding through the neutral conductor is prohibited.

<![if ! IE]>

<![endif]>ENGLISH

28 INSTALLATION

Four-Wire Direct Wire

•• A 4-wire connection is required for all mobile and manufactured home installations, as well as all new construction after January 1, 1996.

•• A UL-listed strain relief is required.

•• Use UL-listed 4-wire #10 AWG-minimum copper conductor cable. Allow at least 5 ft. (1.5 m) of wire to allow for removal and reinstallation of the dryer.

1	Remove 5-inch (12.7 cm) of the outer covering
	from the wire. Remove 5-inch of insulation from
	the ground wire. Cut off approximately 1½-inch
	(3.8 cm) from the other three wires and strip 1
	inch (2.5 cm) insulation from each wire. Bend
	the ends of the three shorter wires into a hook
	shape.
		1" (2.5 cm)
				Ground Wire
	5"
2		(12.7 cm)
	Remove the terminal block access cover on the
	upper back of the dryer.
3	Install a UL-listed strain relief into the power cord
	through-hole.
4	Thread the 4-wire #10 AWG-minimum copper

power cable prepared in step 1 through the strain relief.

Terminal Block

UL-Listed

Strain Relief

UL-Listed 4-Wire Power Cord

5 Transfer the dryer’s ground wire from behind the green ground screw to the center screw of the terminal block.

NOTE

6	Attach the two hot leads of the power cord to the
	outer terminal block screws.
7	Attach the white neutral wire to the center screw
	of the terminal block.
8	Attach the power cord ground wire to the green
	ground screw.

9 Tighten all screws securely.

10 Reinstall the terminal block access cover.

Hot	Neutral
(Black)	(White)
	Hot
Ground	(Red)
Screw	White Wire
	moved from
	Ground
Power Cord	Screw
Ground Wire

This dryer is supplied with the neutral wire grounded. This white ground wire MUST BE MOVED to the neutral terminal when a 4-wire cord is to be used, or where grounding through the neutral conductor is prohibited.

				INSTALLATION 29
Three-Wire Power Cord		8 Reinstall the terminal block access cover.
•• A 3-wire connection is NOT permitted			Hot	Neutral
on new construction after January 1,			(Black)	(White)
1996.				Hot
•• A UL-listed strain relief is required.		Ground		(Red)
		Screw
•• Use a 30-amp, 240-volt, 3-wire, UL-listed power
cord with #10 AWG-minimum copper conductor and
closed loop or forked terminals with upturned ends.		White Wire
1	Remove the terminal block access cover on the	from Dryer
		harness	External Ground
	upper back of the dryer.
2			Wire (If required
	Install a UL-listed strain relief into the power cord		by local codes)
	through-hole.
3	Thread a 30-amp, 240-volt, 3-wire, UL-listed
	power cord with #10 AWG-minimum copper
	conductor through the strain relief.
	Terminal Block
	UL-Listed
	Strain Relief

	UL-Listed 3-Wire Power Cord
4	Attach the two hot leads (black and red) of the
	power cord to the outer terminal block screws.
5	Attach the neutral (white) wire to the center
	terminal block screw.

NOTE

The dryer is supplied with the neutral conductor grounded. If a 3-wire cord is to be used and is allowed, make sure the white neutral grounding wire is connected to the green ground screw.

6	Connect the external ground (if required by local
	codes) to the green ground screw.
7	Tighten all screws securely.

<![if ! IE]>

<![endif]>ENGLISH

30 INSTALLATION

Three-Wire Direct Wire

•• A 3-wire connection is NOT permitted on new construction after January 1, 1996.

•• A UL-listed strain relief is required.

•• Use UL-listed 3-wire, #10 AWG-minimum copper conductor cable. Allow at least 5 ft. (1.5 m) length to allow for removal and installation of dryer.

1	Remove 3½-inch (8.9 cm) of the outer covering
	from the wire. Strip 1 inch (2.5 cm) insulation

from each wire. Bend the ends of the three wires into a hook shape.

1" (2.5 cm)

2	Remove the terminal block access cover on the
	upper back of the dryer.
3	Install a UL-listed strain relief into the power cord
	through-hole.
4	Thread the 3-wire, #10 AWG-minimum copper
	conductor power cable prepared in step 1
	through the strain relief.

Terminal

Block

UL-Listed

Strain Relief

	UL-Listed 3-Wire Power Cord
5	Attach the two hot leads (black and red) of the
	power cord to the outer terminal block screws.
6	Attach the neutral (white) wire to the center
	terminal block screw.

NOTE

The dryer is supplied with the neutral conductor grounded. If a 3-wire cord is to be used and is allowed, make sure the white neutral grounding wire is connected to the green ground screw.

7	Connect the external ground (if required by local
	codes) to the green ground screw.
8	Tighten all screws securely.
9	Reinstall the terminal block access cover.

Hot Neutral

(Black) (White)

Hot

Ground (Red)

Screw

White Wire

from Dryer
harness	External Ground
	Wire (If required by
	local codes)

Final Installation Check

Once you have completed the installation of the dryer and it is in its final location, confirm proper operation with the following tests and Installation Test (Duct Check) on the following page.

Testing Dryer Heating

GAS MODELS

Close the dryer door, press the POWER button to turn the dryer on, and start the dryer on a heat setting. When the dryer starts, the igniter should ignite the main burner.

ELECTRIC MODELS

Close the dryer door, press the POWER button to turn the dryer on, and start the dryer on a heat setting. The exhaust air should be warm after the dryer has been operating for 3 minutes.

Checking Airflow

Effective dryer operation requires proper airflow. The adequacy of the airflow can be measured by evaluating the static pressure. Static pressure in the exhaust duct can be measured with a manometer, placed on the exhaust duct approximately 2 ft. (60.9 cm) from the dryer. Static pressure in the exhaust duct should not exceed 0.6-inch (1.5 cm). The dryer should be checked while the dryer is running with no load.

Checking Levelness

Once the dryer is in its final location, recheck the dryer to be sure it is level. Make sure it is level front to back and side to side, and that all four leveling feet are firmly on the floor.