Lenco LED-2214 User Manual

22” (55.5cm) Full HD LED TV WITH DVB-S

Model No.: LED-2214

For information and support, www.lenco.eu

Contents

1-3 SAFETY INFORMATION

Unit4 5-6 7

8-11 12 13

14 15-22

Remote Control

Aerial connection

Connecting external devices

Common Interface slot

Auto installation setup

Source menu

Menu settings

DVBS Operation23-37

38 39

TROUBLE SHOOTING GUIDE

TECHNICAL SPECIFICATIONS

options

SAFETY INFORMATION

IMPORTANT SAFETY INSTRUCTIONS - READ CAREFULLY BEFORE USE.

Take note of the following safety information which appears on the back of the TV.

CAUTION TO PREVENT ELECTRICAL SHOCK, DO NOT REMOVE ANY COVER SCREWS, NO USER SERVICEABLE PARTS INSIDE, REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This symbol indicates that there are important operating maintenance instructions in the literature accompanying this unit.

This symbol indicates that dangerous voltage constituting a risk of electric shock is

present within this unit.

Keep these instructions

• Do not use this TV near water.

• Clean only with a slightly damp cloth.

• Do not block any ventilation openings.

• Install in accordance with the supplied Quick Start Guide and this User Guide.

• Protect the power chord from being walked on or pinched, particularly at plugs, and the point where it exits from the TV.

• Do not allow the power chord to overhang the edge of a table.

• Unplug this TV during lightening storms or when unused for long periods of time.

WARNING! TO REDUCE THE RISK OF FIRE OR ELECTRICAL SHOCK, DO NOT EXPOSE THIS TV TO RAIN OR MOISTURE. THE TV MUST NOT BE EXPOSED TO DRIPPING AND SPLASHING AND NO OBJECTS FILLED WITH LIQUIDS SHOULD BE PLACED ON THE TV.

NOTE: No naked flames such as candles should be placed on the TV.

IMPORTANT SAFETY INFORMATION(Continued)

This unit has been produced according to all current safety regulations. The following safety tips should safeguard users against careless use and the dangers connected with such use.

x Although this appliance has been carefully manufactured and rigorously checked

prior leaving the factory, as with all electrical appliances it is possible for problems to develop. If you notice smoke, an excessive build up of heat or any other unexpected phenomena, you should disconnect the plug from the mains power socket immediately.

x Ensure that the unit is sufficiently ventilated! Never place next to or underneath

curtains!

x The mains plug or appliance coupler is used as the disconnect device, the disconnect

device shall remain readily operarble.

x This set should only be connected to a mains power supply which matches that

stated on the label on the rear of the TV – do not attempt to connect it to any other type of supply.

x The socket – outlet must be installed near the equipment and easily accessible. x To prevent overload, don’t share the same mains supply socket with too many other

items of equipment.

x Apparatus with Class 1 construction shall be connected to a mains socket outlet with a protective earthing connection.

x Keep away from rodents. Rodents enjoy biting into electric flexes. x Always hold the plug when pulling out the plug from the mains supply socket. Do not

pull on the flex, the flex can become overloaded and cause a short circuit.

x Set up the unit so that no one is able to trip over the flex. x Do not place heavy items on the flex, which may damage it. x Take note that the flex cannot be reached and pulled by young children, avoiding

injury.

x Do not set up the unit near to heat sources. The casing and the flex could be

damaged by the impact of heat.

x The screen is made of plastic and can break if damage is done to it. Be careful when

collecting sharp edged plastic splinters to avoid injury.

x Avoid placing the unit on any surfaces that may be subject to vibrations or shocks. x To protect the unit during a thunderstorm unplug the AC power cable and disconnect

the aerial. Caution: Do not touch the aerial (RF) connector.

x When you leave your home for long periods of time, unplug the AC power cable for

safety reasons.

x The unit becomes warm when in operation. Do not place any covers or blankets on

the unit in order to prevent overheating. The ventilation holes are not to be blocked. Do not set up near radiators. Do not place in direct sunshine. When placing on a shelf leave 5 cm (2”) free space around the whole unit.

x Do not allow water or moisture to enter the TV. Do NOT use in wet or moist areas

such as Bathrooms, steamy kitchens or near swimming pools.

x Do not use this unit when moisture condensation may occur x Any repairs must be carried out by qualified personnel only. x Do not open this unit. A non – expert attempting to repair the unit could be dangerous

and potentially cause a fire hazard.



IMPORTANT SAFETY INFORMATION (continued)

Liquids spilt into the unit can cause serious damage. Switch the set OFF and

disconnect the mains power supply, then consult a qualified service person before attempting to use the unit again.

Do NOT remove the safety covers. There are no useable or serviceable parts inside.

You may invalidate the warranty. Qualified personnel must only service this apperatus.

Do NOT tap or shake the screen, you may damage the internal circuits. Take good

care of the remote control, do not drop. Never place hot objects or open flame sources on or close to the TV. High temperatures can melt plastic and lead to fires.

To clean the TV use a soft dry cloth. Do NOT use solvents or petrol based fluids. For

stubborn stains, you may use a damp cloth with dilute detergent.

Headphone Warning

Loud music can damage your hearing irreversibly, therefore do not set the volume to a high level when listening through headphones, particularly for lengthy listening periods.

Where to install

Locate the television away from direct sunlight and strong lights, soft indirect lighting is recommended for comfortable viewing. Use curtains or blinds to prevent direct sunlight falling on the screen. Place the TV on a sturdy platform of which the surface should be flat and steady. This will prevent it from falling over. Make sure the television is located in a position where it cannot be pushed or hit by objects, as pressure will break or damage the screen, and so that small objects cannot be inserted into the ventilation slots or openings in the cabinet.

Unit and Accessories

LED Indicator

Remote Control Window (keep clear)

The functions of the TV buttons are described below.

MENU Press to display the OSD menu, Press again to exit the menu. : CH-/CH+: Press to scan through channels.

They are also can be used to move down/up in the OSD menu screen. VOL-/VOL+: Press to adjust the volume. They are also can be used to move left/right in the OSD menu screen.

VOL+ button can be used to skip forward to next menu. INPUT: Press to select the source.

Power: Turn on/off the TV set.

Remote control

USB

DVBS-SAT

FAV

PIC-FORMAT

DISPLAY

TV/RADIO

DVBS-AUDIO

SUBTITLE TEXT

PAUSE EPG

DVBS-INFO

INPUT

EXIT

POWER:

Turn the TV on/standby.

Buttons for TELETEXT(In ATV mode) TV/TXT: Teletext on/off CANCEL: Turn off the Teletext display

REVEAL: Reveal any hidden text, for example-quiz answer

NICAM/A2

HOLD

: Hold or carry on the current subpage

SIZE: Press to see top half of page double size, Press again to see the bottom half of page double size,

Press again for normal size

SUBPAGE: press to subpage, again to cancel.

INDEX: go to index.

Colour buttons: short cuts-follow the coloured links in

the text. (In DTV mode, press red key to switch between TV and radio.

Green key, yellow key and blue key are invalid.)

MENU : System setup menu.

INPUT: Press to display the input source menu.

CH+/- : Scan through channels. VOL+/- : Adjust the volume. Cursor left/right up/down : Cursor buttons used in menus.

OK:CONFIRM BUTTON for menu.

EXIT : Exit the OSD menu. USB:

The short cuts to the multtimedia in DVBS mode.

CH+/- : Scan through channels. VOL+/- : Adjust the volume. Cursor left/right up/down: Cursor buttons used in menus.

OK:CONFIRM BUTTON for menu.

0-9,-/--

Choose channel directly.

Returns to the previous channel.



Remote control (continued)

USB

DVBS-SAT

FAV

PIC-FORMAT

DISPLAY

TV/RADIO

DVBS-AUDIO

SUBTITLE TEXT

PAUSE EPG

DVBS-INFO

INPUT

EXIT

PICTURE: Select the picture mode. SOUND: Select the sound mode. DISPLAY: Display current mode information. MUTE: Mutes the Audio.

SLEEP: Standby Timer.

TV/RADIO: Disc menu change between TV and Radio.

DVBS-SAT: Display the satellite list.

DVBS-AUDIO: Shows the list of available languages for the

channel you are watching.

DVBS-INFO: Shows information of the current channel. F

AV: Display the favorite program list.

SUBTITLE: To switch the dialogue at the bottom of the

screen.

TEXT: To view the teletext broadcasting program.

PIC FORMAT: Press to change the display mode of the

screen: 4:3, 16:9.etc

PAUSE: Pause the current screen in DVB-S.

EPG: To show the Electronic Program Guide during

no-menu state only.

Aerial connection

WARNING! ENSURE THE TV AND ALL ANCILLARY EQUIPMENT IS UNPLUGGED FROM THE MAINS BEFORE MAKING ANY CONNECTIONS!

Connecting the TV Antenna

Connect the TV antenna to the aerial socket with a 75 ohm co-axial plug. For best results use a high gain TV aerial, preferably roof or loft mounted.

• To improve picture quality in a poor signal area, purchase and install a signal amplifier.

• If the antenna needs to be split for two TVs, use a 2-Way Signal Splitter (not supplied).

USER GUIDE

Connecting external devices

This instruction manual shows the simplest and most effective way of connecting your TV to ancillary equipment. Alternate methods are listed below.

HDMI Lead

You can connect this TV to a compatible device using a HDMI lead. This method will give the best picture.

Connect the cable from the HDMI equipment to the TV HDMI socket.

SCART Lead

You can connect this TV to a compatible device using a SCART lead. The connection uses component video signals, content of the video are sent on separate signals.

VGA Cable

You can use your TV as a monitor for your personal computer by using a VGA cable. Sound from your personal computer may also be played through the TV.

i.e. the red, green and blue (RGB)

Connecting external devices (continued)

SCART

POWER: Connect to the mains adaptor.

USB: USB jack for Multi-Media playback and PVR.(

Do not use USB extension cable to connect any USB device.)

HDMI: Connect it to the HDMI of DVD or other equipment.

VGA: For PC display.Connect it to the D-Sub 15 pins analog output connector of the PC.

PC-IN: Connect it to the audio output terminal of PC.

SCART: Connect them to the SCART video output terminal of DVD.(used in component source)

Headphone: Connect it to your headphone or other audio equipment.

RF: Connect antenna or cable 75 Ohm coaxial to receive TV signal. R/L in: Connect them to the audio output terminal of DVD.(shared with YPbPr) VIDEO: Connect it to video output terminal of DVD. YPbPr: Connect them to the YPbPr video output terminal of DVD.(used in

component source)

Common Interface: CI slot.

Caution:

Before connecting external devices:

Makes sure to disconnect the appliances from the power supply in order to avoid any potential damage from occurring. Make sure to establish the required connection. Make sure that the connectors are properly and correctly attached before connecting the appliances to the power supply.

Connecting external devices (continued)

PC connection

As PCs are sometimes still supplied with a ‘conventional’ CRT monitor, you may need to adjust the display settings of your PCs graphics card, otherwise the pictures may not appear correctly. Switch on your PC (still with your original monitor connected) now select the screen resolution, and select 60Hz refresh rate. Switch off your PC, then connec t it to your TV while both appliances are still switched off.



VGA, HDMI PC Connection

Use a PC-VGA cable (not supplied) to connect the TV to your PC. You can also use an HDMI cable to connect to your PC (if your PC Graphic card supports HDMI). When the HDMI cable is used, the PC audio cable is no longer required. If you use the HDMI to DVI cable, you will need to use the PC audio cable. Connect all cables carefully and do not bend or break the connector pins.

When using the VGA cable

x Switch on the TV x Switch on the PC x Select PC/VGA as input source

When using the HDMI cable

x Select HDMI as input source



( All illustrated cables are not supplied)

VGA cable 

HDMI to DVI cable

Audio cable

HDMI to HDMI





Connecting external devices (continued)



Connecting Video camera and Video recorder

Video camera

x Connect the AV cable to the TV and to the video camera. x Turn on both video camera and the TV. x Select AV/CVBS source x You can now see the playback picture from the video camera.

Note:

To connect the video camera using other cables, refer to the video camera

x

instruction manual.

Video recorder

x Co



x Turn on both video recorder and the TV. x Select Scart source x You can now see the playback picture from the video recorder.

Note:

nnect the Scart cable to the TV and video recorder.



x To connect the video recorder using other cables, refer to the video recorder



instruction manual.

Video recorder

Scart cable

Video camera

AV cable

 All illustrated cables are not supplied

+ 30 hidden pages