Legrand AU1011-WH User Manual

INSTRUCTION/INSTALLATION SHEET
FLUSHMOUNT TRIPLE SOURCE

301 Fulling Mill Road, Suite G
Middletown, PA 17057
Phone [phone] / Fax [phone]
www.onqlegrand.com

1. Introduction

The On-Q/Legrand Flush Mount Triple Source Input, PN
AU1011-xx (see Figure 1), is a wall mounted fixed version of the
lyriQ™ Triple Source Input Unit. It is a component which, when
combined with other essential components and your audio
source equipment, creates a versatile whole-house multi-source
audio system that will fill your rooms with high-quality sound for
years to come. The Flush Mount Triple Source Input may be
combined with a Single Source Input to provide up to 4 audio
sources to the lyriQ™ Four Source, Eight Zone Distribution
Module in the enclosure. The Category 5 technology utilized for
whole house audio distribution with the lyriQ™ system provides
many advantages over other conventional methods of audio
distribution such as a low noise Category 5 wiring scheme, and
infrared control of system components. The Flush Mount Triple
Source Input is available in white (-WH), light almond (-LA) and
black (-BK).

2. Description

The Flush Mount Triple Source Input typically resides at the entertainment center location and is connected to
the enclosure-mounted lyriQ™ Four Source, Eight Zone Distribution Module (4x8) using two Catego ry 5 cable
runs. The Flush Mount Triple Source Input receives up to three line level
source equipment. If your devices do not have dedicated line level or preamp output, use the tape monitor
outputs. The Flush Mount Triple Source Input provides three sets of RCA jacks for audio source equipment
connection and an adjustable gain control for each to balance the inputs. The green LED next to each set of
RCA jacks indicates an active audio source. IR signal distribution is supported by three (3) IR Emitter Output
ports (IR on Tip, no connection to Ring and Sleeve is grounded) and one (1) IR Target input port (+12V on
Tip, IR on Ring and Sleeve is grounded). The IR Target input is routed only to the three Emitter outputs. A red
LED is provided to indicate IR activity.

3. Installation

IMPORTANT: Read all technical information that is included with all associated ly riQ™ Audio
products before installation of any single component. If you are unsure of any of the following
installation procedures contact On-Q/Legrand Technical Support @ 1-800-321-2343 option 1 or
contact an On-Q/Legrand installer.

NOTE: The Flush Mount Triple Source Input, like other On-Q/Legrand lyriQ™ Audio system
components, is powered by the On-Q/Legrand lyriQ™ Four Source, Eight Zone Distribution Module.

A. Run two Category 5 cables from a two-gang low voltage bracket or electrical box at the room location

containing the Flush Mount Triple Source Input (typically the entertainment center location) to the lyriQ™
Four Source, Eight Zone Distribution Module located in the Enclosure.

B. Make sure that the Power Supply is not connected to the Audio Distribution Module at this time.

INPUT

IS-0406 REV. A

stereo audio outputs from the audio

Figure 1

Page 1 of 2

©Copyright 2008 by On-Q/Legrand All Rights Reserved.

INSTRUCTION/INSTALLATION SHEET
FLUSHMOUNT TRIPLE SOURCE

301 Fulling Mill Road, Suite G
Middletown, PA 17057
Phone [phone] / Fax [phone]
www.onqlegrand.com

C. Pull the Category 5 cables out through the low voltage bracket and plug

them into the RJ45 Cat 5e jacks on the rear of the Flush Mount Triple
Source Input (see Figure 2). Then mount the Flush Mount Triple Source
Input into the low voltage bracket and cover with a wall plate.

D. Connect up to three RCA interconnect cables from the receiver/

pre-amplifier line level output (2nd zone out, tape 1 out, tape 2 out, etc.)
to the AUDIO IN jacks of the Flush Mount Triple Source Input (see
Figure 3). It is recommended that you DO NOT use a pre-amp (or non
fixed output) from a receiver/pre-amplifier. If this is used the output will
be post the receiver/pre-amplifier volume control thus making the output
to the Flush Mount Triple Source Input vary with the volume setting of
the receiver/ pre-amplifier. If a FIXED output like tape 1 or tape 2 is used,
it is independent of the volume setting of the receiver/pre-amplifier thus
allowing the lyriQ™ Volume Controls to have full control over the sound
level.

NOTE: If the TAPE OUTPUT jack is used and must be shared with a
Tape Deck, then audio Y cables can be used.

E. If IR control is being used, plug the emitters (available separately) into the IR EMITTER outputs and place

them onto the IR receiver windows of the source equipment via the peel away adhesive strip.

F. If the Universal IR Target, PN F7426 (available separately), is being used, plug it into the IR INPUT jack on

the Flush Mount Triple Source Input.

G. Check all other system components and then apply power to the lyriQ™ Four Source, Eight Zone Distribution

Module in the Enclosure.

H. The Green LED on the front of the Flush Mount Triple Source Input lights to indicate an active audio source.

The Red LED indicates any IR activity.

Figure 3

INPUT

IS-0406 REV. A

RJ45 jacks

Figure 2

Page 2 of 2

©Copyright 2008 by On-Q/Legrand All Rights Reserved.