This document contains proprietary information of Lanner Electronics Inc. –and is not to be disclosed or used except in accordance with
applicable agreements.
The information in this document is furnished for informational use only, is subject to change without notice, and should not be
construed as a commitment by Lanner Electronics Inc. Lanner Electronics Inc. assumes no responsibility or liability for any errors or
inaccuracies that may appear in this document or any software that may be provided in association with this document.
HOW TO USE THIS DOCUMENT................................................................................................................................................3
SAFETY INFORMATION ...........................................................................................................................................................3
5.6.3 LAN Destination ..............................................................................................................................................29
8.6.1 Video Record ...................................................................................................................................................53
9
B-FOCUS 442 GW User Manual
About this product
Purpose
The purpose of this document is to connection and management information for IP KVM-IC2300 through IPMI
service.
Intended audience
This document is for individuals who configure and manage IP KVM-IC2300.
How to use this document
Use this guide to install or configure the IPMI service on the server system.
Safety information
WARNING: The following information lists the safety reminders for installation and maintenance personnel.
Read all instructions before attempting to unpack, install, operate, or connect power to this product. Please remember
the following when you unpack and install this equipment:
Keep the chassis area clear and dust-free during and after the installation. Do not wear loose clothing or
jewelry that could get caught in the chassis.
Fasten your tie or scarf and roll up your sleeves.
Wear safety glasses if you are working under any conditions that might be hazardous to your eyes.
Do not perform any action that creates a potential hazard to people or makes
the equipment unsafe.
Disconnect all power by turning off the power and unplugging the power cord before installing or removing a
chassis or working near power supplies
Do not work alone if potentially hazardous conditions exist.
Never assume that power is disconnected from a circuit; always check the circuit.
Operating Safety
Electrical equipment generates heat. Ambient air temperature may not be adequate to cool equipment to
acceptable operating temperatures without adequate circulation. Be sure that the room in which you choose to
operate your system has adequate air circulation.
Ensure that the chassis cover is secure. The chassis design allows cooling air to circulate effectively. An open
chassis permits air leaks, which may interrupt and redirect the flow of cooling air from internal components.
Electrostatic discharge (ESD) can damage equipment and impair electrical circuitry.
ESD damage occurs when electronic components are improperly handled and can result in complete or
intermittent failures. Be sure to follow ESD –prevention procedures when removing and replacing components
to avoid these problems.
Wear an ESD-preventive wrist strap, ensuring that it makes good skin contact.
If no wrist strap is available, ground yourself by touching the metal part of the chassis.
Periodically check the resistance value of the antistatic strap, which should be between 1 and 10 megohms
(Mohms).
EMC Notice
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case users will be required to correct the interference at their own expense.
3
Version 1.0
Class A Notice for FCC
Modifying the equipment without the authorization of Lanner Electronics, Inc. may result in the equipment no longer
complying with FCC requirements for Class A digital devices. In that event, your right to use the equipment may be
limited by FCC regulations, and you may be required to correct any interference to radio or television communications
at your own expense.
This equipment is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.
Conventions used
Following are all the special characters and typographical conventions used in this manual:
Convention Meaning
Press Enter Means press the Enter or Return key or its equivalent on your
computer.
Note
Introduces important additional information.
Caution
Warns that a failure to follow the recommended procedure could result
in loss of data or damage to equipment.
Warning
Warns that a failure to take appropriate safety precautions could result
in physical injury.
Warning
Warns of danger of electric shock.
4
Chapter 1
1. About the IP KVM-IC2300
The IP KVM-IC2300 contains a powerful software stack combining the functionality of a Service Processor
and of a Baseboard Management Controller (BMC). The software implements IPMI 2.0 and KVM/IP based on
the service processor. It performs all the BMC management tasks defined by IPMI 2.0, which acts as a
service processor, allows for video redirection and remote monitoring using KVM over LAN. For remote
access, it runs an embedded web-server to provide a web management interface. It also runs a remote
desktop service for direct access to the system’s desktop. The following section provides a list of software
capabilities.
2. Features
IPMI Message Interface Support
Version 1.0
Introduction
• KCS (System Interface Support)
• IPMB
• LAN
• USB
Media Redirection
• Simultaneous floppy, Hard disk or USB and CD or DVD redirection.
• Efficient USB 2.0 based CD/DVD redirection with a typical speed of 20XCD.
• Support for USB key
• Completely secured (Authenticated or Encrypted) remote KVM or vMedia.
IPMI 2.0 based management
• BMC stack with a full IPMI 2.0 implementation
• Customizable sensor management
Event Log and Alerting
• Read Log events
• Sensor readings
5
Version 1.0
• SNMP traps
• E-Mail alerts
Sophisticated User Management
• IPMI based user management
• Added security with SSL (HTTPS)
• Multiple user permission level
• Multiple user profiles
Remote Server Power Control
• Server’s power status report
• Support for remotely power-cycle, power-down, power-up and server reset
Web based configuration
• Full configuration using web UI
• Fail-safe firmware upgrade
• Multi-language support in Web interface with English as the currently supported language
6
Version 1.0
3. Safety Guidelines
In order to reduce the risk of fire, electric shock and injury, please adhere to the following safety guidelines.
9 Carefully follow the instructions in this manual; also follow all instruction labels on this device.
9 Only use the power adapter supplied with the device.
9 Do not spill liquid of any kind on this device.
9 Do not place the unit on an unstable stand or table; the unit may drop and become damaged.
9 Do not expose this unit to direct sunlight.
9 Do not place any hot devices close to this unit, as it may degrade or cause damage to it.
9 Do not place any heavy objects on top of this unit.
9 Do not use liquid cleaners or aerosol cleaners. Use a soft dry cloth for cleaning.
7
Version 1.0
4. Hardware Installation
1. Plug the AC adapter into an AC power socket, and connect its jack to the system’s power socket. If the system is
not powered on, you will need to startup the IPMI service first.
2. To start the IPMI service separately without powering on the system, connect the console cable to the system’s
console port.
3. Start the IPMI service as described in the following section.
4. When the booting process finishes, you could access the IPMI web interface through the IPMI port.
5. Open the browser and type in the default login username and password.
5. Connecting IPMI via Console Port
In case when you want to start the IPMI service alone without powering on the system, you can use the console port.
The console port’s configuration is as follows:
Baud rate: 38400
Data bit: 8
Parity: none
Stop bit: 1
Flow control: hardware
Username: sysadmin
Password: superuser
When the console port is connected, the terminal will display the message to ask you to press the ESC key within 5
seconds to bypass the system startup and enter the IPMI U-Boot Command Line Interface. You should do so
accordingly if you want to start the IPMI service manually before the console being redirected to be used for the
overall system .
After entering the U-Boot menu, type bootfmh to start up the IPMI service. You may also config the Ethernet
information of the LAN port for IPMI service with the ifconfig command. The original Ethernet configuration is as
follows:
The device is pre-configured with the following parameters. You may change the default values using the web
interface. Refer to 5.9.4Users.
Web Management Interface
User Name:admin
Password: [admin]
Local port address: 192.168.0.100
Subnet mask: 255.255.255.0
Console Connection
User Name: sysadmin
Password: superuser
9
Version 1.0
Chapter 2
Web Configuration Interface
1. Overview
The Web Management Interface is provided to let the configuration of the IPMI service as easily as possible. It
provides a user-friendly graphical interface through a Web platform. In the next chapter, each configuration item is
described in detail. Here we list the supported Internet browsers through which you can use to access these
functions.
Browser Version
Firefox 2.0 and above Yes: Default Yes No
Internet Explorer 7 and above No Yes: Default No
Safari 3.0 and above No Yes Yes: Default
Chrome 2.0 and above No Yes No
Opera 9.64 and above No Yes No
Operating System
Linux Windows MAC OS
2. Preparation
Step 1: Please refer to the hardware installation procedure in Chapter 1 to prepare the device for IPMI
management.
Step 2:You should configure your PC to the same IP subnet as the IPMI interface.
Example
Step 3:Connect your PC to the IPMI port directly or to any network device such as a switch which also
connects to the IPMI interface. Make sure that the PING function is working properly.
Step 4:Launch the Web browser (IE or Netscape) and enter the default IP address 192.168.0.100 into the
address bar to access the Web management page.
Step 5: The Login dialog box will appear first.
: IPMI Interface: 192.168.0.100
Your PC: 192.168.0.x
10
Version 1.0
Login
The Enter Network password window will appear when starting the configuration. Type admin for the User name
and admin for the Password, then click the Login button.
Note: The username and password are case-sensitive.
11
3. Dashboard
3.1 Dashboard Information
Version 1.0
The Dashboard shows the hardware monitor information.
It monitors several critical parameters in PC hardware, including power supply voltages, fan speeds for both CPU and
system fans, temperatures, and CPU voltage, etc.
Device Information
The Device Information displays the following information:
Firmware Revision: The revision number of the firmware.
Firmware Build Time: This field shows the date and time on which the firmware is built.
Network Information
The Network Information of the device with the following fields is shown here. To edit the network Information, click
Edit.
MAC Address: Read only field showing the IP address of the device.
V4 Network Mode: The IPv4 network mode of the device which could be disable, static or DHCP.
IPv4 Address: The IPv4 address of the device (could be static or DHCP).
V6 Network Mode: The v6 network configuration of the device which could be disable, static or DHCP.
IPv6 Address: The IPv6 address of the device.
12
Version 1.0
Remote Control
To redirect the host remotely, launch Java Console from this section.
Click Launch to launch the console redirection and to manage the remote server. It will start downloading the
jviewer.jnlp file which after downloaded and launched will open the Java redirection window.
Sensor Monitoring
It lists all the available sensors on the device with the following informations.
• Status: The status column displays the state of the device. There are three states for status.
- Denotes normal state
-Denotes Warning State
- Denotes Critical State
If you click the
sensor readings, see next section on Server Health.
icon, the sensor reading for that particular sensor will be displayed. For more information on
13
Version 1.0
4. Server Health Group
The Server Health Group consists of the following two items.
• Sensor Readings
• Event Log
4.1 Sensor Readings
The sensor readings page displays all the sensor related information. Click on a record to show more detailed
information such as the thresholds about that particular sensor.
Sensor Type (drop down menu)
This drop down menu allows you to select the type of sensor. The List of sensors with the Sensor Name, Status and
Current Reading will be displayed in the list. If you select All Sensors, all the available sensor details will appear.
Otherwise, you can choose the sensor type that you want to display in the list. Some examples of other sensor types
include Temperature Sensors, Fan Sensors, and Voltage Sensors etc.
Select a particular sensor from the list. On the right hand side of the screen you can view the Thresholds for this
sensor.