WS-9055TWC
Wireless 433 MHz
Weather Station
Instruction Manual
TABLE OF CONTENTS
Topic |
Page |
Quick Setup |
3-5 |
Inventory of Contents |
6-7 |
Detailed Setup Guide |
7 |
Battery Installation |
|
Setting the Time |
8 |
Features |
9 |
Minimum and Maximum |
|
Temperatures |
10 |
Resetting Minimum and |
|
Maximum Temperatures |
10-11 |
Adding additional remote |
|
temperature sensors |
|
(optional) |
12 |
Weather Forecast |
|
Weather Icons |
13-14 |
Tendency Arrow |
14 |
Mounting |
15-16 |
Troubleshooting |
16-18 |
Maintenance and Care |
18-19 |
Specifications |
19-20 |
Warranty Information |
21-26 |
2
QUICK SETUP
Hint: Use good quality Alkaline Batteries and avoid rechargeable batteries.
1.Have the indoor temperature station and remote temperature sensor 3 to 5 feet apart.
2.Batteries should be out of both units for 10 minutes.
3.Place the batteries into the remote temperature sensor first then into the indoor temperature
station.
(All remote temperature sensors must be started before the indoor temperature station)
4.DO NOT PRESS ANY BUTTONS FOR 15 MINUTES.
In this time the indoor temperature station and remote temperature sensor
3
will start to talk to each other and the display will show both the indoor temperature and an outdoor temperature. If the indoor temperature station does not display both temperatures after the 15 minutes please retry the set up as stated above. After both indoor and outdoor temperatures are displayed for 15 minutes you can place your remote temperature sensor outdoors and set your time.
The remote temperature sensor should be placed in a dry, shaded area. The remote temperature sensor has a range of 80 feet. Any walls that the signal will have to pass through will reduce distance. An outdoor wall or window can have up to 30 feet of resistance and an interior wall can have up to 20 feet of resistance.
4
Your distance plus resistance should not exceed 80 ft. in a straight line. NOTE: Fog and mist will not harm your remote temperature sensor but direct rain must be avoided.
To complete the set up of your indoor temperature station after the 15 minutes have passed please follow the steps in the detailed set up guide on page 8.
INVENTORY OF CONTENTS
1.The indoor weather station (Figure 1)
2.The remote temperature sensor (TX6U) and mounting bracket. (Figure 2)
3.3 each, 1/2” Philips screws.
4.One strip of double sided adhesive tape.
5.Instruction Manual and Warranty Card.
5
Figure 1
Figure 2
Holder
ADDITIONAL EQUIPMENT
(not included)
1.1 Philips screwdriver.
2.2 Fresh AA Alkaline batteries.
3.2 Fresh AA Alkaline batteries
DETAILED SETUP
GUIDE
Battery Installation
6
1.Install 2 AA batteries in the remote temperature sensor. Make sure they do not spring free, or start-up problems may occur.
2.Install 2 AA batteries in the indoor weather station. Do not press any buttons for
at least fifteen
minutes. Setting the time
1.Press and hold the “SET” key for 4 seconds.
2.The hour will flash.
3.Press and release the “+” key to advance the hour.
4.Press and release the “SET” key.
5.The minute is flashing.
6.Press and release the “+” key to advance the minutes.
7
7.Press and release the “SET” key to exit programming.
FEATURES
Minimum and Maximum
Temperatures
1.Press and release the “MIN/MAX” button, “MAX” appears between the indoor and remote temperatures.
2.The recorded maximum indoor and remote temperature is displayed.
3.Press and release the “MIN/MAX” button.
4.“MIN” appears between the indoor and remote temperatures.
5.The recorded minimum temperature is displayed.
6.Press and release the “MIN/MAX” button to exit min/max mode.
7.To view optional additional sensors, press and release the “CH” button
8