Kyocera FS-6025, FS-6030MFP Service Bulletin 2K3 0024 B432
Q’
Com
bi
p
ati-
Boss at the cassette backside and
Contact with the base
direction
Boss at the cassette backside
direction
Service Bulletin Ref. No.
(Page.1/2)
2K3-0024 (B432)
<Date> December 15, 2011
Subject Measures against the Standard Cassette Withdrawing Failure
Model
FS-6030MFP, FS-6025MFP, FS-6025MFP/B, FS-C8020MFP,
FS-C8025MFP
Topic
If the conditions 1 to 3 below are met, the boss of the paper width cursor supporting point on the backside of the
cassette contacts the machine base edge protection material, which might make difficult to withdraw the cassette.
Therefore, the following was made.
Conditions
1. A3/11x17 size paper is fully loaded in the standard cassette. (No problem occurs with other cassette.)
2. A3/11x17 size paper load is applied for a prolonged time due to low copy volume.
3. The cassette heater is ON.
Content of Changes
A GUIDE was added to the backside of the cassette so that the boss will not contact the base edge protection
material and the cassette can be smoothly withdrawn.
(Paper width cursor support point)
No.
Old Part
No.
302K393170
1
2K393170
302K39K170
2
2K39K170
303NN93010
3
3NN93010
303NN9K010
4
3NN9K010
5 --------
New Part
No.
302K393171
2K393171
302K39K171
2K39K171
303NN93011
3NN93011
303NN9K011
3NN9K011
302K394900
2K394900
*1: Machine’s standard cassette and the first cassette of PF
*2: Second cassette of PF (The cassette other than standard cassette and first PF cassette was also added for common use.)
*3: Please note that the final order for this part may be requested in three years after issue of this service bulletin.
base edge protection material
Cassette
withdrawing
Description
CT-475 1 1 X O *1
CT-475(KR) 1 1 X O *1
CT-476 1 1 X O *2
CT-476(KR) 1 1 X O *2
+ PARTS GUIDE BOTTOM
CASSETTE ASSY SP
ty
Old New Old New
- 1 - O
edge protection material
Cassette
withdrawing
lity
Set of the
GUIDE/Screw/leaflet
*3
Remarks
European Service & Development Center (ESDC)
KYOCERA MITA Europe B.V.
Cassette backside
GUIDE
attached
and the
GUIDE
attach
ed on
the
Service Bulletin Ref. No.
KMC’s Classification Entire Stock Rework In-Field modification at next visit
Field Measure: Please install the part No.5 to the cassette when the phenomenon described above arises.
Serial Nos. of the Affected Machines: From the November 2011 production
<How to install the GUIDE>
A: GUIDE B: Screw
- Clean the area where to affix the GUIDE on the cassette
backside with alcohol.
- Peel off the release paper from the double-sided tape on the
GUIDE (marked A above) and affix the GUIDE aligning
to the boss and the screw hole, and fix it with the screw.
(For more details, please refer to the bundled leaflet.)
(Page.2/2)
2K3-0024 (B432)
<Date> December 15, 2011
In-Field modification by case No modification necessary
cassette backside
KYOCERA MITA Europe B.V.
European Service & Development Center (ESDC)
cassette installed in the
main unit
Loading...