Page 1
17. IGNITION SYSTEM
17-0
PEO PLE 25 0
17
__________________________________________________________________________________
__________________________________________________________________________________
__________________________________________________________________________________
__________________________________________________________________________________
__________________________________________________________________________________
IGNITION SYSTEM
__________________________________________________________________________________
IGNITION SYSTEM LAYOUT --------------------------------------- 17-1
SERVICE INFORMATION -------------------------------------------- 17-2
TROUBLESHOOTING ------------------------------------------------- 17-2
SPARK PLUG ----------------------------------------------------------- 17-3
IGNITION COIL INSPECTION --------------------------------------- 17-3
A.C. GENERATOR INSPECTION ------------------------------------ 17-4
CDI UNIT RESISTANCE INSPECTION----------------------------- 17-4
17
Page 2
17. IGNITION SYSTEM
17-1
PEO PLE 250
IGNITION SYSTEM LAYOUT
IGNITION CIRCUIT
Pulser Coil
Ignition Switch
Ignition Coil
CDI Unit
A.C. Generator
Page 3
17. IGNITION SYSTEM
17-2
PEO PLE 250
SERVICE INFORMATION
GENERAL INSTRUCTIONS
• Check the ignition system according to the sequence specified in the Troubleshooting. (!1-28)
• The ignition system adopts CDI unit and the ignition timing cannot be adjusted.
• If the timing is incorrect, inspect the CDI unit and A.C. generator and replace any faulty parts.
Inspect the CDI unit with a CDI tester
• Loose connector and poor wire connection are the main causes of faulty ignition system. Check
each connector before operation.
• Use of spark plug with improper heat range is the main cause of poor engine performance.
• The inspections in this section are focused on maximum voltage. The inspection of ignition coil
resistance is also described in this section.
• Inspect the ignition switch according to the continuity table specified in page 19-3.
• Inspect the spark plug referring to Section 3.
• Remove the A.C. generator and pulser coil referring to Section 10.
SPECIFICATIONS
Item
Standard
Spark plug
Standard type
NGK DPR7EA9
Spark plug gap
0.7mm
Ignition timing
“F” mark
Full advance
repeatedly
Primary coil
3.6_ 4.1W
Ignition coil resistance
(20℃ )
Secondary
without plug cap
14KW
coil
with plug cap
19KW
Pulser coil resistance (20℃ )
105_ 110W
Exciter coil resistance (20℃ )
1.8_ 2.1W
Ignition coil primary side max. voltage
14V
Pulser coil max. voltage
1.6V
Exciter coil max. voltage
14V
TESTING INSTRUMENT
Electric tester: YF-3501
TROUBLESHOOTING
No spark at plug Engine starts but turns poorly
• Faulty spark plug • Ignition primary circuit
• Poorly connected, broken or shorted wire —Faulty ignition coil
• Faulty ignition switch —Poorly connected wire or connector
• Faulty ignition coil —Poorly contacted ignition switch
• Faulty CDI unit • Ignition secondary circuit
• Faulty A.C. generator —Faulty ignition coil
—Faulty spark plug
—Faulty high-tension wire
—Poorly insulated plug cap
• Improper ignition timing
—Faulty A.C. generator
—Stator not installed properly
—Faulty CDI unit
Page 4
17. IGNITION SYSTEM
17-3
PEO PLE 250
SPARK PLUG
For spark plug inspection and adjustment,
refer to page 3-5.
IGNITION COIL INSPECTION
Remove the seat and met-in box. (!2-6)
Remove the ignition coil
IGNITION COIL CONTINUITY TEST
Inspect the continuity of the ignition coil,
primary coil and secondary coil.
Measure the ignition coil resistances at
20℃ .
Primary coil
3.6_ 4.1W
Secondary coil
without plug cap
14KW
Secondary coil with
plug cap
19KW
Electric tester: YF-3501
Ignition Coil
This is a general test. Accurate ignition
coil test must be performed with a CDI
tester.
＊
Ignition Coil
Secondary Coil
Primary Coil
Ignition Coil
Page 5
17. IGNITION SYSTEM
17-4
PEO PLE 250
A .C. GENERATOR INSPECTION
EXCITER COIL/PULSER COIL
INSPECTION
Remove the seat and met-in box. (!2-6)
Disconnect the A.C. generator connector.
Measure the exciter coil resistance between
the black/white wire terminal and ground.
Black/white_ Ground
8.1MW
Electric tester: YF-3501
For A.C. generator removal/installation, refer
to pages 10-3 and 10-6.
Disconnect the pulser coil wire coupler.
Measure the pulser coil resistance between
the blue/white and green/white wire terminals.
Blue/Yellow_ Green/Whit
e
105_ 110
W
Electric tester: YF-3501
CDI UNIT
RESISTANCE INSPECTION
Measure the resistance between the terminals.
Replace the CDI unit if the readings are not
within the specifications in the table below.
This test is performed with the stator
installed in the engine.
＊
Measure the resistance in the XW range.
＊
Pulser Coil Wire Coupler
Page 6
17. IGNITION SYSTEM
17-5
PEO PLE 250
Unit: W
(-)
(+)
L/Y
B/Y
G/GR
G/W
B/W
G/B
V/R
V/B
V/GGY/G
L/Y∞∞
93KW∞∞
49.3KW
149KW
46.1KW
46.1KW
∞
B/Y
11MW
∞
11MW
991W
∞
11MW
11MW
11MW
11MW
∞
G/GR∞∞∞∞∞∞∞∞∞∞
G/W
93KW
∞
13MW∞∞
50KW
150KW
47KW
47KW
∞
B/W
11MW
984W
∞
11MW
∞
11MW
11MW
11MW
11MW
18MW
G/B∞∞∞∞∞∞∞∞∞∞
V/R
50KW
∞
12MW
49KW∞∞
99KW
4KW
4KW
∞
V/B
150KW
∞
12MW
150KW∞∞
99KW
103KW
103KW
∞
V/G
46KW
∞
12MW
47KW∞∞
4KW
103KW
0.5W
∞
G
46KW
∞
12MW
47KW∞∞
4KW
103KW
0.5W
∞
Y/G∞∞∞∞∞∞∞∞∞∞
Electric tester: YF-3501
• Due to the semiconductor in circuit, it
is necessary to use a specified tester
for accurate testing. Use of an
improper tester in an improper range
may give false readings.
• In this table, “Needle swings then
returns” indicates that there is a
charging current applied to a condenser.
The needle will then remain at “∞ ”
unless the condenser is discharged.
＊
Loading...