o Preset drum/bass grooves with flexible effects
o Fat synth lead sounds
o Acoustic instruments like trumpet, digeridoo, sitar, and more
o Tap-able drum voices
o Extra thick and juicy basses
o Complete chords with filters and other effects
o Space-age sound effects to send your loop beyond the cosmos
• Adjustable scale and key functions
• Layer an unlimited amount of sounds together
• FIX function allows you to create an “undo point,” in case you need to re-record a layer
• Built-in gating arpeggiator with 50 different patterns
• 4x AA Battery operation for total portability (optional AC adapter available)
• It’s yellow!
KKAAOOSSSSIILLAATTOORR MMaaiinn FFeeaattuurreess
s
EEaassyySSttaarrtt CCoonntteenntts
2
2
2
3
3
3
3
4
4
MMaakkiinngg CCoonnnneeccttiioonnss
1. The Kaossilator can run on either 4-AA batteries, or you can power it with our optional 4.5v AC adapter. Because Korg rocks as
hard as we do, we’ve included 4-AA batteries in the box to get you started. Slide the back cover off and load ‘em up!
a. The display will show “Lo” when the batteries are indeed low.
2. As far as outputs go, you have two options:
a. The RCA LINE OUT jacks on the top of the Kaossilator- plug into any mixer, amplifier, recorder, or RCA-equipped
deep fryer.
b. The 1/8” stereo PHONE jack on the bottom of the Kaossilator.
Kaossilator EasyStart
:The VOLUME DIAL next to the PHONE jack only adjusts the headphone volume, not the RCA line out jacks.
NNoottee:
PPllaayyiinngg wwiitthh SSoouunnddss
Enough setup… Time to make noise! Turn that little freakbox on and start playing!
1. Turn the PROGRAM/VALUE DIAL to change the sound you’re making, from 00 to 99.
2. To the left of the number, you’ll see a letter, eitherL, A, B, C, S, D, orP.
- L = Lead synth sounds
- A= Acoustic sounds
- B = Bass sounds
- C = Chords
- S = Sound effects
- D = Drums
- P = Patterns
:The Lead, Bass, and Sound effect categories each have 20 sounds; the other categories have 10 sounds.
NNoottee:
SSeelleeccttiinngg aa SSccaallee
Sure, it doesn’t have keys… but that doesn’t mean the Kaossilator help you write the next big hook! You can control a full TWO
OCTAVES of notes just by touching the pad! Just to make sure you’re playing in the same mode as everyone else, you can choose
what kind of scale you’d like to use…
1. Press the SCALE button.
2. The display should read “Ion
3. Turn the DIAL to select from the 31 scale types.
:Wanna get microtonal? Turn the DIAL counter-clockwise until it says “
NNoottee:
CChhoooossiinngg aa KKeeyy
The same way you can select a scale, you can also choose the key in which to create your madness.
1. Hold down the SCALE button and press the TAP/BPM button.
2. The display should read “C”. Were we doing that science quiz, you would have passed.
.”
No, you’re not about to fail a science quiz.
OFF
.”
2
3. Turn the DIAL to choose the key.
a. The circle next to the key indicates a SHARP, i.e. the black notes on a piano.
b. You can select from two octaves’ worth of keys. The lines on the upper/lower part of the display indicate whether
you’re in the high or low octave.
Kaossilator EasyStart
CChhaannggiinngg tthhee BBPPMM
What, 120 isn’t good enough for you? Fine, go ahead and change it if you must. There are two ways to do it:
1. Press the TAP/BPM button, and then turn the DIAL to change the BPM. After a few seconds, the display will return to the
program selection.
a. If you don’t want to wait a few seconds, just press the SCALE button twice.
2. Tap the TAP/BPM button (who’d have guessed?) at least twice, and the BPM will follow your tapping.
UUssiinngg tthhee GGaattee AArrppeeggggiiaattoorr
Add some serious bounce to your loop with the Gate Arpeggiator!
1. Press the GATE ARP/TYPE button to turn the Arpeggiator on. The red LED is your oh-so-subtle clue that it’s on.
2. To change the type of arpeggiator you want to use, hold down the GATE ARP/TYPE button until you see a “G” in the display.
Turn the DIAL to select one of the 50 patterns.
RReeccoorrddiinngg//OOvveerrdduubbbbiinngg
Found a sound you like yet? Found a whole bunch of ‘em? So… lay them down! First, set the length of the loop:
1. Hold down the LOOP REC/PLAY button, and press the TAP/BPM button.
2. Turn the DIAL to change the length of the loop.
Now to record the first part:
3. Hold down the LOOP REC/PLAY button, and touch your finger on the pad to start recording.
a. It WILL NOT start recording until you touch the pad!
4. Either release the LOOP REC/PLAY button to stop recording, or it will automatically stop and play back when you reach the end
of the loop.
Next, to overdub:
5. To overdub (layer) another sound, just turn the dial to select a new sound, and then repeat steps 3 and 4.
a. Yes, you really can do this as MANY TIMES AS YOU WANT!
Note: To erase the loop and start over, just hold the LOOP REC/PLAY button, turn the dial until “Clr” is displayed, and then