Konica Minolta MAGICOLOR 2300W, MAGICOLOR 2300 DL, MAGICOLOR 2300 User Manual

®

magicolor 2300
Series
Repacking Guide

1760504-001A

Trademarks

KONICA MINOLTA and the KONICA MINOLTA logo are trademarks or registered
trademarks of KONICA MINOLTA HOLDINGS, INC.

magicolor is a trademark or registered trademark of KONICA MINOLTA PRINTING
SOLUTIONS U.S.A., INC. All other trademarks are the property of their respective
owners.

Copyright Notice

Copyright © 2004 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., Marunouchi
Center Building, 1-6-1 Marunouchi, Chiyoda-ku, Tokyo, 100-0005, Japan. All Rights
Reserve d. This document may not be copied, in whole or part, nor transferred to a ny
other media or language, without written permission of KONICA MINOLTA BUSINESS
TECHNOLOGIES, INC.

Manual Notice

KONICA MINOLTA BUSINESS TECHNOLOGIES, INC. reserves the right to make
changes to this manual and to the equipment described herein without notice.
Considerable effort has been made to ensure that this manual is free of inaccuracies
and omissions. However, KONICA MINOLTA BUSINESS TECHNOLOGIES, INC.
makes no warranty of any kind including, but not limited to, any implied warranties of
merchantability and fitness for a particular purpose with regard to this manual.
KONICA MINOLTA BUSINESS TECHNOLOGIES, INC. assumes no responsibility for,
or liability for, errors contained in this manual or for incidental, special, or
consequential damages arising out of the furnishing of this manual, or the use of this
manual in operating the equipment, or in connection with the performance of the
equipment when so operated.

Attention

Failure to follow these instructions could result in voiding your
warranty.

Storing the Printer

Unplug the printer when storing it for an extended period. Protect it from extremes in temperature and humidity, and from dust.

Relocating Your Printer

Occasionally, you may have to move your printer to a different location, either nearby or to a distant location. To avoid damage to your printer, we advise you to follow the next instructions very carefully.

1 Turn off your printer. 2 Remove the power cord and all interface cables. 3 If you are moving to a distant location, follow the instructions for repacking

the printer. (See “Repacking the Printer” on page 2).

4 Relocate the printer.

WARNING!

Your printer weighs approximately 62 lbs (28 kg). Be sure to have
help when lifting and moving it.

5 Unpack and set up the printer in its new location.

Use the unpacking and setup instructions in the Installation Guide.

6 Reconnect the power cord and all interface cables.

" We strongly suggest that you save the packaging materials in case

you ever need to move or ship the printer.

You can also refer to the Service & Support Guide for sources of service and
support in many areas of the world. The most up-to-date worldwide
information can be found at printer.konicaminolta.com/support

Storing the Printer

.

1

Repacking the Printer

Attention

Failure to follow these instructions could result in voiding your warranty.

If you need to relocate or ship your printer after it’s been installed, follow the procedures in this chapter to prevent damage to the printer and to keep your warranty valid.

Attention

KONICA MINOLTA cannot be held responsible for damage to your
printer during shipment that results from the improper packaging of
your printer. You must use the instructions given in this section before
repacking the printer in its original shipping carton with the original
packing materials. If you do not have your original outer packaging, you
must order the appropriate Replacement Packaging Kit:

Kit Name Part Number

magicolor 2300 DL Replacement Packaging Kit 2600723-100

magicolor 2350 Replacement Packaging Kit 2600723-200

magicolor 2300W Replacement Packaging Kit 2600723-300

If you’re relocating or returning the printer, you must also request a
magicolor 2300 Series Repacking Kit 2600733-100. This kit includes
special packaging for the OPC drum cartridge and transfer belt unit.

These supplies must be replaced prior to shipping the printer. If you
need replacement packaging, in the Americas, call the Spares
department at [phone] extension 2530 and request the kit(s)
above. For locations outside the Americas, refer to
printer.konicaminolta.com

If you have been instructed to return the printer to KONICA MINOLTA
PRINTING SOLUTIONS U.S.A., INC. by a customer support
representative in the Americas, be sure to write the RMA (Return
Merchandise Authorization) number you received on the outside of both
the printer and consumables cartons before shipping them. If the RMA
number is not prominently visible on the outside of the return inventory,
we will not accept receipt.

You can also have a KONICA MINOLTA authorized service provider
uninstall and repack your printer, or you can upgrade to on-site service.
For prices and availability, call 1 [phone] in the Americas or see
printer.konicaminolta.com worldwide.

.

Repacking the Printer2

What’s Involved?

Repacking your printer for shipment involves the following steps. Each is described in more detail in the following sections.

Obtain Proper Packaging:

Original packaging or replacement packaging

magicolor 2300 DL Replacement Packaging Kit 2600723-100
magicolor 2350 Replacement Packaging Kit 2600723-200, or
magicolor 2300W Replacement Packaging Kit 2600723-300

Repacking kit

magicolor 2300 Series Repacking Kit 2600733-100

Prepare the Printer for Shipment:

A. Turn off the printer, unplug the power cord, and remove the

interface cables.

B. Remove the media and the tray 1 media support. page 4

C. Remove the duplex option and lower feeder unit, if attached,

and repack them separately.

D. Remove the waste toner bottle, plug the openings, and

dispose of it according to your local regulations.

E. Remove the OPC drum cartridge and repack it. page 7

F. Remove the transfer belt and repack it. page 8

G. Insert the fuser separators. page 9

H. Repack the printer for shipment. page 11

I. Repack the OPC drum cartridge and transfer belt for

shipment.

page 2

page 3

page 4

page 7

page 13

A. Turn off the Printer, Unplug the Power Cord, and Remove the Interface Cables

Repacking the Printer

3

B. Remove the Media and the Tray 1 Media Support

1 Remove the media.

Place it in its original packaging and store in a cool, dark place on a level
surface. Avoid moisture, excess humidity, direct sunlight, excess heat
(above 95° F/35° C), and dust.

2 Lift the media support from the three

holes in Tray 1 and remove the media
support.

C. Remove the Options (if Attached)

Duplex Option

 If you don’t have a duplex option installed, skip to the next section.

1 If you have a lower feeder unit

attached, you first need to open the
lower right-side door.

2 Pull the right-side door release

lever, and open the right-side door.





Repacking the Printer4