Konica Minolta MAGICOLOR 2210 User Manual

®

magicolor 2200
Series
Repacking Guide

1760337-001B

Trademarks

The following are registered trademarks of MINOLTA-QMS, Inc.: QMS, the
MINOLTA-QMS logo, and magicolor.

Minolta is a trademark of Minolta Co., Ltd. Other product names mentioned
in this guide may also be trademarks or registered trademarks of their
respective owners.

Proprietary Statement

The digitally encoded software included with your printer is Copyrighted ©
2001 by MINOLTA-QMS, Inc. All Rights Reserved. This software may not be
reproduced, modified, displayed, transferred, or copied in any form or in any
manner or on any media, in whole or in part, without the express written
permission of MINOLTA-QMS, Inc.

Copyright Notice

This guide is Copyrighted © 2001 by MINOLTA-QMS, Inc., One Magnum
Pass, Mobile, AL 36618. All Rights Reserved. This document may not be
copied, in whole or part, nor transferred to any other media or language,
without written permission of MINOLTA-QMS, Inc.

Notice

MINOLTA-QMS, Inc. reserves the right to make changes to this guide and to
the equipment described herein without notice. Considerable effort has
been made to ensure that this guide is free of inaccuracies and omissions.
However, MINOLTA-QMS, Inc. makes no warranty of any kind including, but
not limited to, any implied warranties of merchantability and fitness for a
particular purpose with regard to this guide. MINOLTA-QMS, Inc. assumes
no responsibility for, or liability for, errors contained in this guide or for
incidental, special, or consequential damages arising out of the furnishing of
this guide, or the use of this guide in operating the equipment, or in
connection with the performance of the equipment when so operated.

Attention

Failure to follow instructions as outlined in the
result in voiding your warranty.

Repacking Guide

Storing the Printer

Keep the following in mind when storing the printer for an extended period:

1

Unplug the printer.

2

Remove the OPC drum, the fuser oil roller, and toner cartridges from the
printer and place them in their original, or protective, packaging. If the
original packaging is not available, protect the toner cartridges from
spilling toner, and protect the OPC drum cartridge from damage and light.

Relocating Your Printer

Occasionally, you may have to move your printer to a different location, either
nearby or to a distant location. To avoid damage to your printer, we advise
you to follow the next instructions very carefully.

1

Turn off and unplug your printer.

2

If the printer has a lower feeder unit and/or a 5-bin mailbox, remove them.

3

If you are moving the printer to a distant location, follow the instructions
for repacking the printer.

4

Relocate the printer.

could

WARNING!

Your printer weighs approximately 87.1 lbs (39.5 kg) without
consumables. Be sure to have help when lifting and moving it.

ACHTUNG! Das Gewicht dieses Druckers beträgt ohne
Verbrauchsmaterial ca. 39.5 kg. Bitte versuchen Sie niemals, den
Drucker alleine anzuheben oder zu transportieren.

5

Unpack and set up the printer in its new location.

6

Reinstall the accessories you removed in step 2.

We

5"

Refer to the
information on where to obtain assistance if necessary

strongly

case you ever need to move or ship the printer.

Service & Support Guide

Storing the Printer

suggest that you save the packaging materials in

or www.minolta-qms.com for additional

1

Shipping the Printer

If you need to relocate or ship your printer after it’s been installed, follow the
procedures in this chapter to prevent damage to the printer and to keep your
warranty valid.

If you’re returning just the printer for service, do not return the

5"

interface cables, power cable, documentation, media tray(s), or
accessories.

Attention

MINOLTA-QMS cannot be held responsible for damage to your printer
during shipment that results from the improper packaging of your
printer. You must use the instructions given in this section before
repacking the printer in its original shipping carton with the original
packing materials. Original shipping cartons are secured using
disposable strapping and buckling supplies. These supplies must be
replaced prior to shipping the printer. If you need replacement
packaging, in the United States, call MINOLTA-QMS Spares at
[phone] extension 2530 and request catalog number
260674-901A. For locations outside the United States, refer to the

Service & Support Guide

printer for service, be sure to write the RMA (Return Merchandise
Authorization) number you received from your customer support
representative on the outside of the carton before shipping the printer.

or www.minolta-qms.com. If you return the

If the printer is not strapped or if the RMA number is not
visible on the outside of the return inventory, we will not accept receipt.
You can also have a MINOLTA-QMS authorized service provider
uninstall and repack your printer. For prices and availability, in the
United States call 1 [phone].

Repacking the Printer

What's Involved?

Repacking your printer for shipment involves the following steps. Each is
described in more detail in the following sections.

1

Remove the cables.

2

Remove the fuser oil roller.

3

Remove the toner cartridges.

4

Remove the waste toner pack.

Shipping the Printer2

prominently