KOHLER K-99571-TL, K-99572-TL, K-99573-TL Installation Manual

Installation and Care Guide

Lighted Mirror

K-99571-TL, K-99572-TL, K-99573-TL

Français, page“ Français-1”
Español, página“ Español-1”

1292979-2-A

IMPORTANT SAFETY INSTRUCTIONS

When using electrical products, basic precautions should always be followed, including the following:

Read all instructions before using or installing this product.

WARNING: Risk of electric shock. Grounding is required for the outlets within the power box.
Connect only to a circuit protected by a Class A Ground-Fault Circuit-Interrupter (GFCI)* which
protects against line-to-ground shock hazard. Use 120 V, 15 A service.

WARNING: Risk of electric shock. A qualified electrician must route all electrical wiring for the
product. Improper installation will create an electrical hazard and may not comply with local
building and electrical codes.

WARNING: Risk of electric shock. Turn the electricity off at the circuit breaker or fuse box before
moving, testing, cleaning, or repairing this product. When unplugged, the electric supply will no
longer be electrically live, which will eliminate the risk of electric shock.

CAUTION: Risk of electric shock. Risk of electric shock. Electrical wiring may need to be
relocated.

NOTICE: Follow all local building, electrical, and plumbing codes.

IMPORTANT! A dimmer switch is required. This product is compatible with most residential dimmers

intended for incandescent and dimmable LED bulbs. For optimal dimming performance, a programmable
digital fade dimmer intended for LED lighting with a minimum rating of 150 W is recommended.

*Outside North America, this device may be known as a Residual Current Device (RCD).

SAVE THESE INSTRUCTIONS

Specifications

Electrical Service

Light 120 V, 60 Hz, 0.8 A

Tools and Materials

Plus:

• Wire Cutter/Stripper

• Assorted Drill Bits

Stud
Finder

1292979-2-A 2 Kohler Co.

Dimmer
Switch

Before You Begin

CAUTION: Risk of personal injury. Mirrors are heavy. Get assistance lifting the unit.
CAUTION: Risk of product or property damage. Swinging panels that are misaligned or set too

close to the main mirror can chip or break. If needed, make adjustments to properly align the
panels with the main mirror.

NOTICE: Risk of product or property damage. The location of the mirror is critical. Make sure the
swinging panels will clear all obstacles (such as a faucet or light fixture), and obstacles behind the finished
wall will not be damaged during the drilling process.

Observe all local building codes.
The appearance of your mirror may differ from the mirror illustrated. The installation instructions

still apply.
This installation is easiest when performed by two people.
For K-99572-TL and K-99573-TL: When determining the height of the product, verify the swinging

panels will clear all obstacles (such as a faucet or light fixture). A minimum distance of 3″ (76 mm)
is required.

Kohler Co. 3 1292979-2-A

3" (76 mm)

3" (76 mm)
Min

Swinging Panels

3" (76 mm)

Dimmer Switch

Roughing-In Information

For K-99572-TL and K-99573-TL: When determining the location of the mirror, verify the swinging
panels will clear all obstacles (such as a faucet or light fixture). A minimum distance of 3″ (76 mm)
is required.

Plan for the location of the dimmer switch. The switch should be located at least 3″ (76 mm) from
the unfolded swinging panels.

1292979-2-A 4 Kohler Co.

Top of Mirror

2-1/2"
(64 mm)

Power
Bar

1. Mark the Power Bar Holes

IMPORTANT! Get assistance when positioning the mirror. One person should hold the mirror in place
while the other person marks the placement.

With help, position the mirror in the desired location on the wall.
Using a pencil, draw a line across the top of the mirror.
Mark the centerline on the line.
Set the mirror aside.
Make a mark on the centerline 2-1/2″ (64 mm) down from the top of the mirror.
Align the top of the power bar with the line for the top of the mirror.
Verify level and mark the two hole locations at the top corners of the power bar.

Kohler Co. 5 1292979-2-A

2-1/2"
(64 mm)

Ø 3/4"

6"
(152 mm)

2. Route the Wiring

Drill a 3/4″ (19 mm) hole for the electrical wire location.
Route the electrical wiring from the dimmer switch through the hole in the finished wall.
The wiring should extend at least 6″ (152 mm) from the hole.

1292979-2-A 6 Kohler Co.

3/16"

3. Install the Power Bar

NOTICE: If conduit is used for routing the dimmer switch wiring, attach the conduit to a 4″ (102 mm)
square electrical plate and secure the plate over the large central hole of the power bar.

Using a 3/16″ drill bit, drill two holes at the marked locations on the finished wall.
Insert the supplied anchors where needed.
Position the power bar on the wall, with the electrical wire pulled through the large central hole.
Verify the bar is level, then secure with two screws provided.

Kohler Co. 7 1292979-2-A

Wire
Connectors

Line
(White)

Wire Connector

Load
(Black)

Light
Cables

Ground
(Green)

4. Connect the Dimmer Switch

Connect the electrical wiring from the dimmer switch to the proper connectors on the power bar as
shown.

Feed the light cables through the slots and tape to the top of the power bar to keep the cables
accessible for later connection.

1292979-2-A 8 Kohler Co.

"J" Hook

5. Position the Mirror

IMPORTANT! Get assistance when hanging the mirror.

IMPORTANT! For K-99572-TL and K-99573-TL: Never leave the swinging panels unsupported during

installation.

For K-99572-TL and K-99573-TL: To ease installation, fold the swinging panels against the main
mirror.

Align the ″J″ hooks on the mirror with the slots in the power bar.
Lower the ″J″ hooks into the slots. The mirror will initially lower approximately 1/4″ (6 mm).
Push the mirror toward the wall to further engage the ″J″ hooks into the slots.

Kohler Co. 9 1292979-2-A

3/16"

6. Mark the Mirror Holes

Mark the two top hole locations on the wall.
Mark the two bottom hole locations on the wall.
Lift the mirror up and out to disengage the ″J″ hooks from the power bar slots.
Set the mirror aside.
Using a 3/16″ drill bit, drill holes at the four marked locations on the finished wall.
Insert the supplied anchors where needed.

1292979-2-A 10 Kohler Co.

7. Secure the Mirror

Reinstall the mirror to the power bar by engaging the ″J″ hooks with the slots. Refer to the ″Position
the Mirror″ section.

Secure the mirror to the finished wall with four screws provided.

Kohler Co. 11 1292979-2-A

8. Connect the Light Cables

Connect the two light cables from the mirrors to the connectors from the power box.
Tuck the wires into the mirror.
For K-99572-TL and K-99573-TL: Verify that the swinging panels move freely without binding the

cables.
Turn on the electrical power to the dimmer switch.
Use the dimmer switch to test the lights for proper operation.

Install the Caps

Press the caps to the top and bottom of the mirror.
For K-99572-TL and K-99573-TL: Install the caps to the top and bottom of the swinging panels.

1292979-2-A 12 Kohler Co.

Gap

Lock
Screws

Jack Screws

Adjust the
tighter gap.

Tilt

Height

9. Panel Adjustment (K-99572-TL and K-99573-TL)

CAUTION: Risk of product or property damage. Swinging panels that are misaligned or set too
close to the main mirror can chip or break. If needed, make adjustments to properly align the
panels with the main mirror.

NOTICE: Alignment of the swinging panels is set at the factory. Adjustments should not be necessary
unless the panels have been replaced.

Fold the swinging panel against the main mirror.
Loosen the lock screws on the top and bottom hinge approximately 1/4 turn clockwise.

Tight Gap Adjustment: Turn the jack screws counterclockwise in 1/4 turn increments at the top
and bottom of the mirror.

Tilt Adjustment: Turn the jack screw counterclockwise in 1/4 turn increments at the top or bottom

of the mirror, whichever has the tighter gap.
Height Adjustment: Turn the screw at the bottom of the mirror to raise or lower the swinging panel

to the same height as the main mirror.
Slowly unfold the panel and check alignment.
Repeat the adjustments as needed.

Care and Cleaning

For best results, keep the following in mind when caring for your KOHLER product:

NOTE: Periodic care and maintenance should include checking all hinge screws on the door to make sure
they are tight and engaged in the hinge holes.

•

Do not let cleaners sit or soak on surfaces.

Kohler Co. 13 1292979-2-A

Care and Cleaning (cont.)

For detailed cleaning information and products to consider, visit www.kohler.com/clean. To order Care &
Cleaning information, call 1-800-456-4537.

Warranty

ONE-YEAR LIMITED WARRANTY

KOHLER plumbing products are warranted to be free of defects in material and workmanship for one year
from date of installation.

Kohler Co. will, at its election, repair, replace or make appropriate adjustment where Kohler Co. inspection
discloses any such defects occurring in normal usage within one (1) year after installation. Kohler Co. is not
responsible for removal or installation costs. Use of in-tank toilet cleaners will void the warranty.

To obtain warranty service contact Kohler Co. either through your Dealer, Plumbing Contractor, Home
Center or E-tailer, or by writing Kohler Co., Attn.: Customer Care Center, 444 Highland Drive, Kohler, WI
53044, USA, or by calling 1-800-4-KOHLER (1-800-456-4537) from within the USA and Canada, and
001-800-456-4537 from within Mexico, or visit www.kohler.com within the USA, www.ca.kohler.com from
within Canada, or www.mx.kohler.com in Mexico.

IMPLIED WARRANTIES INCLUDING THAT OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE ARE EXPRESSLY LIMITED IN DURATION TO THE DURATION OF THIS
WARRANTY. KOHLER CO. AND/OR SELLER DISCLAIM ANY LIABILITY FOR SPECIAL,
INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states/provinces do not allow limitations on how

long an implied warranty lasts, or the exclusion or limitation of special, incidental or consequential damages,
so these limitations and exclusions may not apply to you. This warranty gives you specific legal rights. You
may also have other rights which vary from state/province to state/province.

This is Kohler Co.’s exclusive written warranty.

1292979-2-A 14 Kohler Co.