Knight Equipment FAUCET PLUS Installation Manual

FAUCET PLUS

INSTRUCTION MANUAL

The Knight Faucet Plus is the most effective yet simple way to connect your Knight chemical proportioner to a
commercial kitchen sink. The Faucet Plus includes all the components required to plumb tempered water from a
Fisher, T & S or Chicago faucet head. Follow these simple installation procedures to supply water to your Knight
chemical proportioner.

INSTALLATION

(1) Disconnect faucet head from sink top.
(2) Connect appropriate faucet connector to male thread of sink top placing rubber washer between female

connector and male pipe thread on sink. Use plumbing tape on all joints.
(3) Turn the tee on to the male end of faucet connector. Tighten as required.
(4) Turn the ball valve (female end) on to the tee until tight.
(5) Insert and tighten matching faucet connector to the ball valve.
(6) Re-attach faucet head to connector and tighten as required.
(7) Attach blunt end of High Pressure Hose to 1/2” barb and secure with hose clamp.
(8) Attach 3/4” garden hose connector to proportioner inlet fitting.
(9) Turn on water valves and ball valve to allow water flow to proportioner and check for leaks.

QTY ITEM PART #

Chrome/Nickel Plated Brass

1

Tee, 3/8” NPT
Chrome/Nickel Plated Brass

1

Barb, 3/8” NPT x 1/2” Barb
Chrome/Nickel Plated Fisher

1

Faucet Connectors (x 2)
Chrome/Nickel Plated T & S

1

Faucet Connectors (x 2)
Chrome/Nickel Plated Chicago

1

Faucet Connectors (x 2)
Chrome Plated 3/8” Brass Ball

1

Valve Male x Female
High Pressure Hose 3/4”

1

MGHT x Blunt End, 6 ft.
1 Stainless Steel Hose Clamp 7020150
1 Rubber Washer 2300823

9603083

0600456

0400214

0400217

0400211

9603084

0800427

HIGH PRESSURE

HOSE

HOSE

CLAMP

FAUCET HEAD
MALE CONNECTOR
BALL VALVE

FEMALE CONNECTOR
RUBBER WASHER

0900954 Rev: B (05/07)

DISCLAIMER

Knight LLC does not accept responsibility for the mishandling, misuse, or non-performance of the described items
when used for purposes other than those specified in the instructions. For hazardous materials information consult
label, MSDS, or Knight LLC. Knight products are not for use in potentially explosive environments. Any use of our
equipment in such an environment is at the risk of the user, Knight does not accept any liability in such
circumstances.

WARRANTY

All Knight controls and pump systems are warranted against defects in material and workmanship for a period of
ONE year. All electronic control boards have a TWO year warranty. Warranty applies only to the replacement or
repair of such parts when returned to factory with a Knight Return Authorization (KRA) number, freight prepaid, and
found to be defective upon factory authorized inspection. Bearings and pump seals or rubber and synthetic rubber
parts such as “O” rings, diaphragms, squeeze tubing, and gaskets are considered expendable and are not covered
under warranty. Warranty does not cover liability resulting from performance of this equipment nor the labor to
replace this equipment. Product abuse or misuse voids warranty.

FOOTNOTE

The information and specifications included in this publication were in effect at the time of approval for printing.
Knight, LLC reserves the right, however, to discontinue or change specifications or design at any time without notice
and without incurring any obligation whatsoever.

Knight Headquarters

Tel: [phone]

Fax: [phone]

USA Toll Free

Tel: [phone]

Fax: [phone]

KNIGHT LLC,

Knight Canada

Tel: [phone]

Fax: [phone]

A Unit of IDEX Corporation (www.knightequip.com)

Knight Europe

Tel: [phone]

Fax: [phone]

Knight Australia

Tel: [phone]

Fax: [phone]

0900954 Rev: B (05/07)

Knight N. Asia

Tel: [phone]

Fax: [phone]

Knight S. Asia

Tel: [phone]

Fax: [phone]