Before You Brew
1
Remove packing tape from
brewer and plug into a grounded
Plug & Place
Auto Off
Descale
Strong
Add Water
outlet.
Place a large mug (12oz.
minimum) on the drip tray plate.
3 4
Power On Lift & Lower
Press power button — the green power
light and Auto Off light will illuminate.
The brewer will automatically begin
Auto Off
Descale
Strong
Add Water
heating the water. This will take about 3
minutes. Once the heating sound stops,
the brewer is ready.
2
Rinse & Fill
Remove the water reservoir lid, then lift
the reservoir straight up to remove it.
If you have a Keurig® Water Filter,
install it now. Refer to your Water
Filter Starter Kit for instructions.
Rinse reservoir with fresh water and
fill to the MAX fill line.
Replace water reservoir, making sure the
lock tab engages with the brewer. Replace lid.
NOTE: Do not use distilled water.
Lift and lower the handle. Do not
insert a K-Cup® pod. The four brew
buttons and the Strong button will
blink.
Press the small cup button to start
a cleansing brew. Pour the hot water
into the sink.
The one-time setup process is now
complete and you are ready to brew!
MAX.
Strong
Auto Off
Descale
Strong
Add Water
Auto Off
Descale
Strong
Add Water
Brew Your First Cup
5
Place a mug on the drip tray
plate. If using a travel mug,
remove the drip tray and place
the mug on the drip tray base.
NOTE: Between brew cycles, the brewer may take about a
minute to reheat.
Select your brew size – for bolder coffee,
press the Strong button before selecting
your brew size. The brew size and Strong
button, if selected, will remain illuminated
while brewing – about 1 minute.
The brewer will be ready to brew another
cup in about a minute.
NOTE: After 60 seconds, the brew buttons will be disabled. To re-activate, lift
and lower the handle completely.
CAUTION: While brewing, there is extremely hot water in the K-Cup® pod
holder. To avoid injury, do not lift the handle during the brewing process.
Place Mug
Brew & Enjoy
7
Strong
Auto Off
Descale
Strong
Add Water
12oz.
Large Mug
10oz.
Small Mug
8oz.
Small Cup
6oz.
6
Lift & Insert
Auto Off
Descale
Strong
Add Water
Lift the handle and place a K-Cup®
pod in the K-Cup® pod holder. Lower
the handle completely to close the lid.
Do not remove the foil lid on the
K-Cup® pod.
Brewer Features
Strong Brew kicks up your coffee’s strength and intensity. For bolder coffee, press
the Strong button before selecting your brew size.
Smart Start heats then brews in one simple process. No need to wait for the brewer
to heat before selecting brew size. Power on your brewer, place mug, insert a K-Cup®
pod, and lower the handle. Then, select your brew size. The brewer will heat, then
automatically begin brewing.
Auto Off automatically turns your brewer off 2 hours after the last brew for energy
savings.
To disable the Auto Off feature:
1. Power the brewer off while it is plugged in.
2. Press and hold the Strong and the 10oz. Large Mug buttons for 3 seconds – the green Auto Off light will turn off.
3. Power the brewer on – the green Auto Off light will no longer be illuminated.
To enable the Auto Off feature, repeat steps 1-3. The green Auto Off light will
illuminate.
High Altitude Brewing: To ensure your brewer works properly at higher altitudes
(5,000 feet) please follow these brewing instructions and enable the High
Altitude Brewing Mode on your brewer.
Brewing Instructions - While holding the brewer handle up, push down slowly on the K-Cup® pod in the pod
holder until the bottom of the K-Cup® pod is punctured by the exit needle.
To enable High Altitude Brewing Mode:
1. Power the brewer off while it is plugged in.
2. Press and hold the Strong and 8oz. Small Mug buttons for 3 seconds- both lights will blink 3 times to
confirm that the High Altitude Brewing Mode has been enabled.
To disable High Altitude Brewing Mode:
1. Power the brewer off while it is plugged in.
2. Press and hold the Strong and 8oz. Small Mug buttons until the lights are no longer illuminated.