Keurig K-latte User Manual

Use & Care Guide
Get the most from your new Keurig® brewer
oz
10
oz
8
oz
6
SHOT
LID
WHISK
FROTHER
MAX
MIN
Before You Brew
Add Water
10
8
6
oz
SHOT
oz
oz
LATTE
Add Water
10
8
6
oz
SHOT
oz
oz
LATTE
Add Water
Plug & Place Rinse & Fill
1
Remove pcking tpe from brewer nd frother, nd plug into  grounded outlet. Lower the frother bse on the side of the brewer.
Plce  lrge mug (10oz minimum) on the drip try.
oz
10
oz
8
oz
6
SHOT
LATTE
2
Remove the water reservoir lid, then lift the reservoir straight up to remove it.
Rinse reservoir with fresh water and fill to the MAX fill line.
Replace water reservoir, making sure the lock tabs engage with the brewer. Replace lid.
NOTE: Do not use distilled water.
Add Water
oz
10
oz
8
oz
6
SHOT
LATTE
Clean the Frother
3
Remove the lid and whisk from inside the frother. Wash the interior of the frother, lid, and whisk with warm, soapy water. Dry all parts thoroughly using a soft, non­abrasive cloth, then reassemble.
NOTE: Frother is not dishwasher safe. Do not submerge frother in water. Only use non-abrasive cleaning materials to prevent damage to the inner surface of the frother. Dry interior of frother and base with a soft cloth after cleaning.
Cleansing Brew
5
Lift and lower the handle. Do not insert a K-Cup® pod. The three brew buttons and SHOT button will blink.
Press the 6oz button to start a cleansing brew. Pour the hot water into the sink.
The one-time setup process is now complete and you are ready to brew!
NOTE:
Between brew cycles, the brewer may take about a minute to reheat.
Make Your First Latte
Fill Frother
1
Remove lid and add chilled milk to the MAX line marked in the frother. Replace the lid and place the frother on the frother base.
Press the power button on the frother. The button will illuminate while heating – approximately 3 minutes. Frothing is complete when the button flashes and then turns off.
TIP: Having trouble frothing? We’re here to help. Give us a call at 1-866-901-BREW (2739).
CAUTION:
NOTE: Do not under or overfill frother. Do not operate before adding milk.
Frother is not microwave or dishwasher safe.
Power On
4
4
Press power button - the green power light will illuminate.
The brewer will automatically begin heating the water. This will take about 4 minutes. Once the heating sound stops, the brewer is ready.
oz
10
oz
8
oz
6
SHOT
LATTE
MAX
oz
6
Place Mug & Pod
2
Place a mug on the drip tray. Lift the handle and place any K-Cup® pod in the
Add Water
oz
10
oz
8
oz
6
SHOT
LATTE
K-Cup® pod holder. Lower the handle completely to close the lid.
Do not remove the foil lid on the K-Cup® pod.
Brew a Shot
3
The three brew buttons and SHOT button will blink. Press the SHOT button. Brewing is complete when the SHOT button is no longer illuminated. Lift the handle and dispose of the used K-Cup® pod.
NOTE: After 60 seconds, the brew buttons will be disabled. To re-activate, lift and lower the handle completely.
CAUTION: While brewing, there is extremely hot water in the K-Cup® pod holder. To avoid injury, do not lift the handle during the brewing process.
Create Your Latte
4
Remove the frother from the base. Remove the lid and pour the frothed milk over your shot of coffee.
NOTE: Clean frother immediately after use. For cleaning instructions, see Caring for your Brewer section in this guide.
Brew Your First Coffee
10
8
6
oz
SHOT
oz
oz
LATTE
Add Water
Add Water
10
8
6
oz
SHOT
oz
oz
LATTE
Add Water
10
8
6
oz
SHOT
oz
oz
LATTE
Add Water
10
8
6
oz
SHOT
oz
oz
LATTE
LID
WHISK
FROTHER
Place Mug & Pod
1
Place a mug on the drip tray plate. If using a travel mug, remove the drip tray and place the mug on the drip tray base. Lift the handle and place a K-Cup® pod in the K-Cup® pod holder. Lower the handle completely to close the lid.
Do not remove the foil lid on the K-Cup® pod.
High Altitude Brewing: While holding the
brewer handle up, push down slowly on the K-Cup® pod in the pod holder until the bottom of the K-Cup® pod is punctured by the exit needle.
Brewer Features
Frother froths milk to create your favorite latte.
SHOT button brews a shot of coffee to make delicious,
creamy lattes.
Auto Off automatically turns your brewer off 2 hours after the last brew for energy savings.
Brew & Enjoy!
2
Select your brew size. The button will remain illuminated while brewing — about 1 minute. Brewing is complete when the button is no longer illuminated. Lift the handle and dispose of the used K-Cup® pod.
The brewer will be ready to brew another cup in about a minute.
NOTE: After 60 seconds, the brew buttons will be disabled. To re­activate, lift and lower the handle completely.
CAUTION: While brewing, there is extremely hot water in the
K-Cup® pod holder. To avoid injury, do not lift the handle during the brewing process.
Smart Start heats then brews in one simple process. No need to wait for the brewer to heat before selecting brew size. Power on your brewer, place mug, insert a K-Cup® pod, and lower the handle. Then, select your brew size. The brewer will heat, then automatically begin brewing.
Caring For Your Brewer
Regular cleaning keeps your brewer running smoothly. Always be sure to turn off and unplug your brewer before cleaning.
Water Reservoir & Reservoir Lid
The water reservoir lid and water reservoir should be cleaned periodically. Clean in a dishwasher (top rack only) or hand wash. To hand wash, use a damp, soapy, non-abrasive cloth. Rinse the reservoir thoroughly after cleaning. This will ensure that no cleaning solutions remain in the area as they may contaminate the water supply. After rinsing, fill the reservoir with clean water and return it to the brewer. Do not dry the inside of the water reservoir with a cloth as lint may remain. If needed, repeat above procedures.
NOTE: If you are using a water filter inside the water reservoir, remove it before cleaning.
Drip Tray
The drip tray can hold up to 8 ounces of overflow and should be emptied and cleaned occasionally. To remove, slide it toward you, keeping it level to avoid spilling. Clean in dishwasher (top rack only) or rinse and clean with a damp, soapy, lint-free, non-abrasive cloth.
Frother
Clean immediately after each use and before first use.
To Clean:
1. Remove frother from the base, remove
silicone ring from lid, and remove the whisk from inside the frother.
2. Wash the silicone ring, lid, and whisk with warm, soapy water.
3. Clean the interior of the frother with soap and rinse with warm water. Use a soft, non­abrasive cloth or sponge to prevent damaging the inner coating.
4. Wipe the exterior with a soft, damp cloth.
5. Dry all parts thoroughly and reassemble for
next use.
NOTE: Frother is not dishwasher safe. Do not submerge frother in water. Only use non-abrasive cleaning materials to prevent damage to the inner surface of the frother.
Brewer Exterior
Keep your Keurig® brewer looking its best by cleaning the exterior from time to time. Just clean with a damp, soapy, lint-free, non­abrasive cloth. Never immerse the brewer in water or other liquids.
Loading...
+ 4 hidden pages