Kenwood KRFV-7020-D, KRFV-8020-D, VR-307, VR-309, VR-357 Service manual

AUDIO VIDEO SURROUND RECEIVER
- –
KRF-V7020D/V8020D VR-307/309/357
SERVICE MANUAL
KENWOOD badge (B43-0302-04)
Knob (K27-2293-04)
Knob (K29-7370-02)
Phone jack (E11-0127-05)
Knob (K29-7370-02)
Knob (K29-7323-03)
Knob (K29-7326-04)
© 1999-1/B51-5499-00 (K/K) 1895
Knob (K29-7325-04)
Foot (J02-1407-03)
Miniature phone jack (E11-0293-05)
Lock terminal board (E70-0052-05)
Slide switch (S62-0034-04)
Phono jack (4Px2) (E63-0046-15)
Phono jack (E63-0093-05)
Phono jack (E63-0094-05)
Phono jack (6Px2) (E63-0047-15)
Screw terminal board (E70-0100-05)
Phono jack (E63-1080-05)
Optical receiving module (W02-1181-05)
Phono jack (E63-0164-05)
Power cord bushing (J42-0083-05)
Slide switch (S62-0001-04)
AC outlet (E03-0148-05)
Lock terminal board (E70-0047-05)
AC power cord (E30-2605-05)
Metallic cabinet (A01-3685-01)
Illustration is KRF-V7020D(Y).
Remote Controller
Model Destinations Parts number Model name Battery Cover
KRF-V7020D
X7,C7,Y7,V7,M7 A70-1268-05 RC-R0712 A09-1123-08
KRF-V8020D
X8 A70-1275-05 RC-R0508 A09-0366-08
KRF-V8020D
C8,I8,Y8,M8 A70-1277-05 RC-R0608 A09-0366-08
VR-307
K6,P6 A70-1268-05 RC-R0712 A09-1123-08
VR-309
K8,P8 A70-1277-05 RC-R0608 A09-0366-08
VR-357
K7,P7 A70-1277-05 RC-R0608 A09-0366-08
Resetting the Microcomputer
If the microcomputer may malfunction (unit cannot be operated, or shows an erroneous display) if the power cord is unplugged while the power is ON, or due to some other external factor. If this happens, execute the following procedure to reset the micro­computer and return the unit to its normal operating condition.
Unplug the power cord from the wall outlet, then plug it back in while holding down the POWER key.
Please note that resetting the microcomputer will clear the contents of the memory and returns the unit to the state it was in when it left the factory.
With the power cord plugged in, turn the POWER key OFF. Then, while holding down the ON/STANDBY key, press POWER.
For U.S.A. and Canada
For other countries
FM (T90-0836-05)
RC-R0508/R0608 RC-R0712
Battery cover (A09-0366-08) Battery cover (A09-1123-08)
(E03-0115-05)
indoor antenna (1)
(T90-0833-05)
Loop antenna stand (1)
Batteries (R03/AAA) (4)
*AC plug adaptor (1)
*Use to adapt the
plug on the power cord to the shape
of the wall outlet.
(Accessory only for regions where use is necessary.)
AM loop antenna (1)
Remote control unit (1)Remote control unit (1)
KRF-V7020D/V8020D/VR-307/309/357

CONTENTS / ACCESSORIES / CAUTIONS

Contents

CONTENTS / ACCESSORIES / CAUTIONS...............2
DISASSEMBLY FOR REPAIR.....................................3
CONTROLS.................................................................4
BLOCK DIAGRAM.......................................................6
CIRCUIT DESCRIPTION.............................................7
ADJUSTMENT.......................................................... 14

Accessories

WIRING DIAGRAM....................................................15
PC BOARD ................................................................16
SCHEMATIC DIAGRAM............................................21
EXPLODED VIEW .....................................................35
PARTS LIST...............................................................36
SPECIFICATIONS.....................................................45

Model name vs remote controller

Cautions

2
KRF-V7020D/V8020D/VR-307/309/357
1
2
2
4
4
4
3
x2
x2
x2
x2

DISASSEMBLY FOR REPAIR

1. Remove the 8 screws (1,2,3),
remove the rear panel.
2. Connect the GND of the rear panel and the chassis, the GND of the mounting hardware and the chassis with 2 alligators clip (4)
3
4
8 FUNCTION SHIFT key
Use in combination with the numeric keys to execute alternate commands.
9 Numeric keys
Provide functions identical to those of the original remote control supplied with the component you are controlling. To access the functions printed above the keys, press within 3 seconds of pressing the FUNCTION SHIFT key. Function availability varies for each component.
0 SHIFT key
Use in combination with the AUDIO and VIDEO keys to change the remote control mode without changing the input selector or in combination with the POWER key to turn on and off components programmed into the remote control.
! TV selector key
Sets the remote control to operate a TV or cable box. This key does not change the input selector on the receiver.
@ AUDIO selector key
Selects the audio inputs and sets the re­mote control to operate the respective KENWOOD audio component. If you connect audio components from KENWOOD and other makers to the MD/ TAPE or CD jacks, you can set the remote control to operate these components by registering the appropriate setup code at the respective input.
# GUIDE key
Use to activate the OSD menu functions of registered components.
$ VOLUME key
Use to adjust the receiver volume.
% MUTE key
Use to temporarily mute the sound.
^ SOUND key
Use to adjust the sound quality and ambi­ence effects.
& LISTEN MODE key
Use to select the listening mode.
* SETUP key
Use to select the surround sound settings.
1 POWER key
Use to turn the receiver on and off. Use in combination with the input selector (AUDIO, VIDEO, or TV) keys and SHIFT key to turn various components on and off.
2 MACRO key
Use in combination with the AUDIO, VIDEO, or TV keys to execute a series of commands automatically (MACRO PLAY).
3 VIDEO selector key
Selects the video inputs and sets the remote control to operate the component regis­tered at the respective input.
4 Multi control keys
Use to operate the selected component.
5 REC key
Use to operate the selected component.
6 TUNING/SKIP key
Use during the setup procedure to specify various settings. Use to operate the tuner or selected component.
7 SUBWOOFER key
Use in combination with the VOLUME +/– keys to adjust the volume of the subwoofer.
There are some cases in which keys (or knobs) that have the same function on the receiver and on the remote control have different names. In the instruc­tions of this manual, if the names of corresponding keys (or knobs) on the receiver and remote control are differ­ent, the name of the remote control key is indicated in parentheses.

Remote control unit (RC-R0608 / R0508)

Display
Speaker selection indicators Input channel indicators Output channel indicators
AUTO SOUND indicator
Band indicators
AUTO indicator MEMO. indicator ST. indicator
TUNED indicator
3 STEREO indicator STEREO indicator
1 POWER key
(For U.S.A. and Canada)
Use to turn the power ON/OFF.
STANDBY indicator
1 ON/STANDBY (
) key
(Except for U.S.A. and Canada)
Use to switch the power ON/STANDBY when the POWER is turned ON.
STANDBY indicator
2 POWER key
(Except for U.S.A. and Canada)
Use to turn the main power ON/OFF.
3 Surround indicators
÷ DTS indicator
Lights when the receiver is in the DTS mode. (For VR-309, KRF-V8020D)
÷ DOLBY DIGITAL indicator
Lights when the receiver is in the Dolby Digital mode.
÷ VIRTUAL SURROUND indicator
Lights when the receiver is in the Virtual Surround mode.
4 DIMMER key
Use to adjust the brightness of the display. Use to select the REC MODE.
5 P.CALL keys
Use to call up previously registered radio stations.
6 BAND key
Use to select the broadcast band.
7 AUTO key
Use to select the auto tuning mode.
8 MEMORY key
Use to store radio stations in the preset memory.
9 VOLUME CONTROL knob 0 PHONES jack
Use for headphone listening.
! SPEAKERS A/B keys
Use to turn the speakers ON/OFF.
@ BASS BOOST key
Use to select the maximum adjustment setting for the low frequency range.
About the STANDBY indicator
This unit has a STANDBY indicator. When the STANDBY indicator is lit, the unit consumes a small amount of power to preserve the memory. This is called STANDBY mode. This mode also lets you turn the power ON using the remote control.
Frequency display, Input display, Preset channel display, Surround mode display
Speaker indicator
CLIP indicator
PRO LOGIC indicator
DIGITAL indicator S.DIRECT indicator
MONITOR indicator
DOWNMIX indicator
# MONITOR key $ SOURCE DIRECT key % INPUT MODE key
Use to switch between the digital and analog inputs.
^ LISTEN MODE key
Use to select the listening mode.
& SOUND key
Use to adjust the sound quality and amb ence effects.
* SETUP key
Use to select the surround sound settings
( MULTI CONTROL knob
Used to make a variety of settings.
) INPUT SELECTOR knob
Use to select the input sources.
For U.S.A.
and Canada
MUTE indicator
For VR-307, VR-357 KRF-V7020D
KRF-V7020D/V8020D/VR-307/309/357
SP
B
A
MUTE
CLIP
2
AV SURROUND RECEIVER
STANDBY
POWER
ON / STANDBY
1
STANDBY
ON / STANDBY
POWER
- ON – OFF
PHONES
LS
L
LFE
SPEAKERS
A
R
C
SW
S
RS
DOLBY DIGITAL
VIRTUAL SURROUND
DTS
DOLBY DIGITAL
VIRTUAL SURROUND
B
BASS BOOST
4 6 75
P.CALL P.CALL
DIMMER
SOURCE
INPUT MODE LISTEN MODE
MONITOR
DIRECT
BAND
MULTI CONTROL INPUT SELECTOR
SOUND
SETUP
AUTO SOUND
FM
PRO LOGIC
AM MHz
3 STEREO
kHz
DOWNMIX
AUTO
AUTO
DIGITAL
MEMO.
S.DIRECT
MONITOR
ST.
TUNED
83
MEMORY
9
)(%$#@!0 ^ &*
VOLUME CONTROL
DOWN
1
2
3
4
5
6
7
UP
8
9
POWER
SHIFTMACRO
AUDIO
TVVIDEO
8
P. CALL P. CALL
BAND
6
7
GUIDEREC
VOLUMETUNING/SKIP
MUTE
LISTEN
SOUNDSUBWOOFER
MODE
FUNCTION
SHIFT
THEME FAVMENU
INFO ALT AUDTV/SAT/VID
REPEAT RANDOM+100
DISPLAY
SETUP
231
564
897
ENT+10
0
0
! @
#
$ % ^
& *

CONTROLS

Remote control unit (RC-R0712)

AUTO (7)key
If tuner is selected as the input source, this key functions as the AUTO key. If CD or MD is selected as the input source, this key functions as the stop key.
TUNING (1 ¡) keys
If tuner is selected as the input source, these keys function as tuning keys. If CD or MD is selected as the input source, these keys function as search keys.
P.CALL (4 ¢) keys
If tuner is selected as the input source, these keys function as P.CALL keys. If CD or MD is selected as the input source, these keys function as skip keys.
3 LISTEN MODE key
Use to select the listening mode.
4 MUTE key
Use to temporarily mute the sound.
5 SOUND key
Use to adjust the sound quality and ambi­ence effects.
6 MULTI CONTROL key
Used to make a variety of settings.
1 Numeric keys
If CD or MD is selected as the input source, these keys function as numeric keys. If tuner is selected as the input source, these keys are used to call up station presets.
2 Component operation keys
Use these keys to operate other compo­nents with system control connections to the receiver.
2 key
If tape is selected as the input source, this key functions as the play key for side B of the cassette (the side facing away from the front of the deck).
BAND (6) key
If tuner is selected as the input source, this key functions as the band selector key. If CD is selected as the input source, this key functions as the play/pause key. If MD is selected as the input source, this key functions as the play key.
DISC SKIP, A/B, +100 key
If CD is selected as the input source, this key functions as the multi-CD player disc skip key. If TAPE is selected as the input source, this (A and B) of a double cassette deck.
7 DVD CONT key
Used to operate DVD player. While holding this key depressed, press any of the keys masked in gray inthe above illustration to operate the corresponding function of a DVD player from KENWOOD. Keys 3, 4, 5, 9 and ! are given the following functions during the DVD player control operation.
3 :TITLE 4 :ENTER 5 :SUB TITLE 9 :MENU ! :OSD
For details, refer to the instruction manual of your DVD player.
8 POWER key
Use to switch the power ON/STANDBY when the POWER is turned ON.
9 SOURCE DIRECT key 0 VOLUME CONTROL key ! SETUP key
Use to select the surround sound settings.
@ MONITOR key # Input selector keys
Use to select the receiver's input source.
123
1
267
2
3 4
5
1 TUNING ¡4 P.CALL ¢
MULTI CONTROL
LISTEN
MODE
TITLE
SOUND
SUB TITLE
VOL.DOWN
6
MD/TAPE TUNER CD PHONO
7
DVD CONT VIDEO 1 VIDEO 2 VIDEO 3
REMOTE CONTROL UNIT
89
VOL.UP
MUTE
ENTER
RC-R0712
POWER
0456
+107
DISC SKIP
A/B +100AUTOBAND
S.DIRECT
MENU
SET UP
OSD
MONITOR
8
9 0
!
CONTROLS
@
#
KRF-V7020D/V8020D/VR-307/309/357
5
6
LINE BUF
PHONO EQ
X05
IC16
NJM2279M
CS4226
LPFLPF LPF LPF
x2x2 x2 x1
M62446SP
6ch E. VOL
with 2ch
TONE CONT.
x0.5
BUF
STK411-230
STK410-030
+20/0dB
+B HITAP
-B HITAP
+B LOWTAP
-B LOWTAP
CD COXIAL
OPTICAL
VIDEO2
IN
DIGITAL
VIDEO3
VIDEO2
VIDEO1
CD
PHONO
TAPE
/MD
MONIPLAY
MONI
/MD
TAPE
VIDEO1
VIDEO3
VIDEO2
VIDEO1
VIDEO1
MONITOR
S-VIDEO IN
REC OUT
Lch
H, P, Rch
H, P, Lch
Rch
Cch
Lch Rch
LSch
RSch
SWch PRE OUT
SP-B
SP-A
AC IN
+5V A.V.R
for u-COM
+15V A.V.R
A.V.R
-15V
+5V
+7V
-7V
A.V.R
5V
for E. VOL
for
u-COM
for FIL AC
(AUDIO and VISUAL) TUNER etc.
for AMP (HI TAP)
for AMP (LOW TAP)
for RELAY SW
TC9163
TC9164
A1
J1
IC6(1/3)
IC7(3/3)
IC7(1/3)
IC7(2/3)
IC6
IC8
IC6(2/3)
VIDEO (Y)SEL
(NOT for K,P TYPE)
Q1
SWITCHED
S1
D1,4
D2
D5
IC1
IC2
-30V
IC13
Q2
IC1IC2
IC8 (2/2)
IC8 (1/2)
IC9
IC7
IC5
IC11
Q3
Q4
Q7
Q5
Q6
Q8
Q9
Q10
Q13
Q11
Q12
IC4
IC3
2.0V/2.2KSWch
PRE OUTPUT
CXP82852-139Q
u-COM
INPUT SEL.
TUNER
TC9162
D1-4
(1/2)
(2/2)
(1/2)
(1/2)
(2/2)
(2/2)
IC10
IC10
IC12
IC11
IC11
IC12
SP. OUTPUT 5CH. SP. 28.3V/8
COXIAL
VIDEO3
SUB
S5
S2
DIG
S4
L,R
MIX IC10
S3
LS,RS
S7
NOSUB
ANA
S1
REC OUT BUF
IC9
S1
S2
S3
S4
S4
S5
S6
S7
S8
S1
S2
S3
IC6(3/3)
ANALOG REC
S7
DIGITAL REC
S8
Q43
Q44
D3
A.V.R
for
for DSP
A.V.R
3.3V
IC14
6dB ATT MUTE
SYNC
AC3 DECODER
SUB DSP
B
A
ABYSS902
YSS902 SDIBSEL=0
SDIBSEL=1
(VISUAL IN/OUT)
S5
S6
DSP
IC1
Lch
Rch
Cch
LSch
RSch
SWch
NJM2279M
IC17 VIDEO (C)SEL
AD/DA etc.
for DSP
-5V A.V.R
IC19
A.V.R
IC18
5V
IC12
for DIR.
A.V.R
5V
NJM2279M
VIDEO SEL
IC4
MONITOR
VIDEO 1
VIDEO 1
VIDEO 2
VIDEO 3
VIDEO OUT
VIDEO IN
200mV/2.2K
200mV/47K
OUT
IN
2.5mV/27K
(AUDIO IN/OUT)
PHONO
OTHER
KRF-V8020D,VR-209
USED
K1
S-VIDEO OUT
1Vp-p/75
0.286Vp-p/75C
Y
S-VIDEO IN/OUT
(VISUAL IN/OUT)
1Vp-p/75
VIDEO IN/OUT
IC51
LFE
DA
AD
2
2
BYPASS
SW
C
LS,RS
L, R
L, R
L
R
C
LS
RS
SW
DIR
C LS/RS L/R
+
+
+
+
+
+
+
4700uF
4700uF
3300uF
470uF
2200uF
3300uF
2200uF
+
2
LR LS,RS C,LFE
L,R
C,SUB
C,SUB
L,R
LS,RS
C
Y
Y C
Y C
Y C
Y C
KRF-V7020D/V8020D
(X00)
(X08)
(X09)
(X08)
VR-307/309/357
KRF-V7020D/V8020D/VR-307/309/357

BLOCK DIAGRAM

CIRCUIT DESCRIPTION

(0 : Pull down, 1 : Pull up)
TYPE BAND
Reception frequency
Channel
IF
PLL standard
Diode sw
space
frequency
DSW3 DSW2 DSW1 DSW0
K1
FM 87.5MHz~108.0MHz 100kHz +10.7MHz 25kHz
0000
1700
AM 530kHz~1700kHz 10kHz +450kHz 10kHz
K2
FM 87.5MHz~108.0MHz 100kHz +10.7MHz 25kHz
0001
1610
AM 530kHz~1610kHz 10kHz +450kHz 10kHz
K4
FM 87.5MHz~108.0MHz 100kHz +10.7MHz 25kHz
1010
1700 RBDS
AM 530kHz~1700kHz 10kHz +450kHz 10kHz
E1
FM 87.5MHz~108.0MHz 50kHz +10.7MHz 25kHz
0011
AM 531kHz~1602kHz 9kHz +450kHz 9kHz
E3
FM 87.5MHz~108.0MHz 50kHz +10.7MHz 25kHz
RDS
AM 531kHz~1602kHz 9kHz +450kHz 9kHz
0101
FM L 65.0MHz~74.0MHz 10kHz +10.7MHz 5kHz
Q1
FM H 87.5MHz~108.0MHz 50kHz +10.7MHz 5kHz
1011
RDS
AM 531kHz~1602kHz 9kHz +450kHz 9kHz
M
K2/E1 is switched with only the setting of DSW1 (X11 : S601).
00X1
(DSW1 = 0 : K2 type, 1 : E1 type)
77 76 75 74

1. The back up item and initialization condition

1-1 Back up
• POWER : POWER OFF
• VOLUME LEVEL : -66dB
• AUDIO INPUT SELECTOR : TUNER
• VIDEO INPUT SELECTOR : VIDEO 1
• SPEAKER A : ON
• SPEAKER B : OFF
• BASS : 0dB
• TREBLE : 0dB
• INPUT LEVEL : 0dB
• SOURCE DIRECT : OFF
• MONITOR : OFF
• DIMMER : DIMMER 1 (LIGHTEST)
• LISTEN MODE : STEREO
• VIRTUAL SURROUND : OFF
• INPUT MODE : DIGITAL AUTO
• SUB WOOFER : YES(ON)
• FRONT SP. SIZE : NORMAL
• CENTER SP. SIZE : NORMAL
• SURROUND SP. SIZE : NORMAL
• DISTANCE : Fch 10ft/3m : Cch 10ft/3m : Sch 10ft/3m
KRF-V7020D/V8020D/VR-307/309/357
• FRONT (L,R) LEVEL : 0dB
• CENTER LEVEL : 0dB
• REAR (LS,RS) LEVEL : 0dB
• SUB WOOER LEVEL : 0dB
• MIDNIGHT : OFF
• BAND : FM
• FM FREQUENCY : 87.50MHz
• AM FREQUENCY : 531kHz(CH.SPACE 9kHz) : 530kHz(CH.SPACE 10kHz)
• PRESET CH. : [ --ch ]
• PRESET MEMORY FREQUENCY : PRESET MEMORY
FREQUENCY
• TUNING MODE : AUTO
1-2 The initial setting
While pressing POWER key, plug the AC power cord into an AC outlet (K,P type) or turn on the AC POWER switch.

2. Condition by the destination or model

3. TEST MODE

[setting method]
While pressing INPUT SELECTOR key, plug the AC power cord into an AC outlet (K, P type) or turn on the AC POWER switch. When a set is set up in test mode condition a set becomes the following condition. Auto­matic POWER ON. All indicator tube (FL) and CLIP INDI­CATOR LED are lighted. The other LED are flashed.
A backup at the thing except ON/OFF of POWER is ini­tialized.
[cancel method]
The power supply is turned off.
7
KRF-V7020D/V8020D/VR-307/309/357
FL DISPLAY (X09) ED51
11GRID
17SEGMENT
X8
X3
X3
X4
X3
X3
X2
X2
X2
(X09) S517
SERIAL
BUSY DATA
VOLUME
ENCODER
(X09) S519
MULTI
ENCODER
(X09) S518
SELECTOR
ENCODER
(X09)
X4 X1
X3
X3
8.0MHz CE RESET
X3
X1
X3
AUDIO MUTE TUNER MUTE
TUNER (X05) IC2
(X05) IC1
-20dB ATT
SD STEREO
X1
11-MT-120GK
LED
(PEAK. LEVEL)
(DOLBY DIGITAL)
(STANDBY)
(X09) IC6,7
AUDIO SELECTOR
(X09) IC51
(X08) IC4,16,17
NJM2279M
(X09) A501 REMOCON
VIDEO SELECTOR IC
TC9163/9164
CXP82852-139Q
(X00) POWER Relay - (K1)
SP. A RELAY - (K1) SP. B RELAY - (K2)
SURR RELAY - (K3)
CENTER RELAY - (K4)
(X08) IC1
DSP IC
(X08) IC2
DIR, ADC, DAC
YSS902 or YSS912
CS4226KQG
(CRYSTAL)
(X08) IC5
FUNCTION SW
(X08) IC11
VOLUME IC
M62446FP
LC72131
TC9162
12
KR0
13
KR1
14
KR2
81
KS0 P.CH DOWN ON/STANDBY SPEAKER A
80
KS1 P.CH UP DIMMER SPEAKER B
79
KS2 BAND LISTEN MODE DOLBY VIRTUAL
78
KS3 AUTO SOUND MONITOR
77
KS4 MEMORY SETUP SOURCE DIRECT
76
KS5 INPUT MODE
75
KS6 DSW0 DSW1 DSW2
74
KS7
* No. of : u -COM Port NO.
DSW3 DSW (AC3)
Key matrix
CIRCUIT DESCRIPTION

4. Microprocessor CXP82852-139Q(X09 : IC51)

4-1 Microprocessor periphery block diagram
8
KRF-V7020D/V8020D/VR-307/309/357
CIRCUIT DESCRIPTION
4-2 Pin description
Pin No. Pin Name I/O Description
1,2 G10,11 O Display grids 10,11
3 None - Ic test mode port.
4,5 None I No connect
6 AUDIO I Audio signal detection port. L=AUDIO. 7 VOL.ENC.A I Volume encoder A(clockwise) input. 8 REMOCON I Remote contol signal input.
9 VOL.ENC.B I Volume encoder B(counterclockwise) input. 10,11 None O Ic test mode port. 12-14 KR0-2 I Key return 0-2.
15 PROTECT I Protection signal detection port. H=PROTECT. 16 S.DATA I/O Serial DATA signal. 17 S.BUSY I/O Serial BUSY signal. 18 SP.A+B O Speaker on both A sp. and B sp. 19 SW.6dB.ATT O Sub woofer 6dB attenuation 20 SEL.ENC.A I Selector encoder A(clockwise) input. 21 SEL.ENC.B I Selector encoder B(counterclockwise) input. 22 MULTI.ENC.A I Multi encoder A(clockwise) input. 23 MULTI.ENC.B I Multi encoder B(counterclockwise) input. 24 SL16/XS8 I SL16/XS8 selector. H=16bit. 25 DSP.SCK O DSP(YSS902/912) CLOCK output. 26 DSP.SI I DSP(YSS902/912) DATA input. 27 DSP.SO O DSP(YSS902/912) DATA output. 28 Vdd - Analog power supply(+5V) 29 None I No connect 30 CH.SPACE O Channel space chengeover H=E1 type 31 DSP.CS O DSP(YSS902/912) CS output. 32 CODEC.CS O CS4226 CS output. 33 PLL.DO I Pll ic DO signal input . 34 PLL.ST I Tuner STEREO signal detection port. L=STEREO. 35 PLL.SD I Tuner SD signal detection port. L=TUNED. 36 RCV.CE I Receiver CHIP ENABLE signal port. L=ENABLE. 37 Avss - Analog GND. 38 RESET I Microproessor RESET signal.
39,40 8MHz I Main clock generation(8MHz).
41 Vss - Microprocessor GND. 42 None I No connect 43 TEX - GND. 44 Vdd - Power supply(+5V). 45 Vfdp - Power supply(-33V). 46 SEL.ST1 O TC9162AF/63AF/64AF ST1 output. H=LATCH. 47 PLL.DT O Pll ic DATA signal output . 48 PLL.CK O Pll ic CLOCK signal output . 49 PLL.CE O Pll ic CE signal output . 50 T.TUNE O Tuner mute control. L=MUTE ON 51 A.MUTE O Audio mute control. L=MUTE ON 52 SEL.ST2 O TC9163/9164 ST2 output 53 20dB.ATT O Volume 20dB attenuation control. H=ATT. OFF 54 VOL.DT O Volume ic (M62446SP) DATA control. 55 VOL.CK O Volume ic (M62447SP) CLOCK control. H=ACTIVE 56 VOL.ST O Volume ic (M62448SP) ST control. H=ACTIVE 57 DSP.SCB O DSP(YSS902/912) chip selector 58 VCR.A O Video ic (NJM2279M) cont1 control. H/L=STATIC 59 VCR.B O Video ic (NJM2279M) cont3 control. H/L=STATIC 60 FA.RLY O Front A speaker relay control. H=RELAY ON
9
KRF-V7020D/V8020D/VR-307/309/357
CIRCUIT DESCRIPTION
Pin No. Pin Name I/O Description
61 FB.RLY O Front B speaker relay control. H=RELAY ON. 62 C.RLY O Center speaker relay control. H=RELAY ON 63 S.RLY O Rear speaker relay control. H=RELAY ON 64 POWER.RLY O Power relay control. H=RERAY ON 65 STANDBY.LED O Standby LED control.H=LED ON 66 DOL.DIG.LED O Dolby digital LED control.H=LED ON 67 DOL.VIR.LED O Dolby virtual LDE control.H=LED ON 68 DTS LED O DTS LED control. H=LED ON
69,70 None O No connect
71 PACk CTL O Non oscillation of power pack ic at power off. L=STOP OSCILLATION 72 DSP.IC O DSP(YSS902/912)/CS4226 initial clear .
73 None O No connect 74-81 P1-8/KS7-0 O Display segments 1-8 & key scan 7-0. 82-88 P9-15 O Display segments 9-15.
89 Vdd O Microprocessor power supply(+5V)
90,91 P16,17 O Display segments 16,17
92-100 G1-9 O Display grids 1-9.
10
XI
XO
CPO
SDOA0
24
19
9
8
23
22
567
12
88
2
89
15
878670
59 61
34
64
58
42 ~ 44
25 ~ 29
52
16
17
53
54
55
56
85
84
82
83
57
92 ~ 99
32 ~ 39
66
67
68
69
65
48
47
46
45
18
49
SDOA1
SDOA2
SDIB0
SDIB1
SDIB2
SDIB3
RAMD0~7
72 ~ 79
RAMCEN
RAMWEN
RAMOEN
RAMA0~16
OVFB
SDOB INTERFACE
SDIB INTERFACE
SDOA INTERFACE
SDIA INTERFACE
CRC
SDIASEL
SDIBSEL
IPORT0~7
CONT.
/SDBCK0
SDBCK0
SDWCK0
SDIA0
SDIA1
SURENC
STREAM0~7
OPERATION
CLOCK (30MHz)
KARAOKE
MUTE
CRC AC3DATA DTSDATA
NONPCM
PLL
DELAY RAM
L, R
Ls, Rs
C, LFE
INPUT
BUFFER
CONTROL REGISTER
U-COM INTERFACE
24 * 24
Main DSP
Dolby digital/ProLogic/DTS
DECODER
COEFFICIENT
PROGRAM
RAM
24 * 16
Sub DSP
DATA RAM
SDOB3
RAMD : RAM data RAMA : RAM address
SDOB2
SDOB1
SDOB0
SDWCK1
SDBCK1
EXT. RAM
INTERFACE
CONT.
SDOACKSEL
SDIBCKSEL
SDOBCKSEL
ERAMUSE
/CS
SO
SI
SCK
OPORT0~7
/CSB
SCK
SI

5. Dolby digital/DTS IC: YSS902/YSS912 (X08: IC1)

5-1 Block diagram (YSS912)
CIRCUIT DESCRIPTION
KRF-V7020D/V8020D/VR-307/309/357
11
KRF-V7020D/V8020D/VR-307/309/357
CIRCUIT DESCRIPTION
5-2 Pin description
Pin No. Pin Name I/O Descriptions
1 Vdd1 - Power supply(+5V) 2~4 - - No connect 5~7 SDIB0~2 O PCM output port for sub DSP
8 XI I Crystal oscillation port.(902:6.25~50.0MHz,912:12.288MHz)
9 XO O Crystal oscillation port.
10 Vss - GND 11 AVdd - Power supply(+3.3V) for PLL
12~18 - - No connect
19 CPO O PLL output port. 20 AVss I GND 21 Vdd2 - Power supply(+3.3V) 22 SDOA2 O PCM output port from main DSP 23 - - No connect 24 SDOA0 O PCM output port from main DSP
25~29 - - No connect
30 Vss - GND 31 Vdd1 - Power supply(+5V) 32 - - No connect 33 OPORT1 O -
34~39 - - No connect
40 Vss - GND 41 Vdd2 - Power supply(+3.3V)
42-44 - - No connect
45 SDO2 O PCM output port from sub DSP(C,LFE/SWch) 46 SDO1 O PCM output port from sub DSP(LS,RSch) 47 SDO0 O PCM output port from sub DSP(FL,FRch)
48,49 - - No connect
50 Vss - GND 51 Vdd2 - Power supply(+3.3V)
52~59 - - No connect
60 Vss - GND 61 - - No connect 62 /IC I Initial clear port.
63,64 - - No connect
66 /CS I Microprocessor interface chip selector input port. 67 SO O Microprocessor interface serial data output port. 68 SI I Microprocessor interface serial data input port. 69 SCK I Microprocessor interface clock input port. 70 - - No connect 71 Vdd1 - Power supply(+5V)
72~79 - - No connect
80 Vss - GND 81 Vdd2 - Power supply(+3.3V) 82 SDIWCK 0 I Word clock for SD input ports. 83 SDIBCK 0 I Bit clock for SD input ports. 84 SDIA I AC3 bit stream data input port.
85~89 - - No connect
90 Vss - GND 91 Vdd2 - Power supply(+3.3V)
92,93 - - No connect
94 IPORT5 I Input port register 95 - - No connect
96~99 IPORT3~0 I Input port register
100 Vss - GND
12
Loading...
+ 25 hidden pages