Kenwood KMM-118 User Manual [es]

KMM-118

DIGITAL MEDIA RECEIVER

INSTRUCTION MANUAL

RÉCEPTEUR MULTIMÉDIA NUMÉRIQUE

MODE D’EMPLOI

RECEPTOR DE MEDIOS DIGITALES

MANUAL DE INSTRUCCIONES

For your records

Record the serial number, found on the back of the unit, in the spaces designated on the warranty card, and in the space provided below. Refer to the model and serial numbers whenever you call upon your Kenwood dealer for information or service on the product. Model KMM-118 Serial number

US Residents Only

CONTENTS BEFORE USE

BEFORE USE 2

BASICS 3

GETTING STARTED 4

1 Select the display language

and cancel the demonstration 2 Set the clock and date 3 Set the initial settings

RADIO 5

USB/iPod/ANDROID 7

AUX 9

AUDIO SETTINGS 10

DISPLAY SETTINGS 11

TROUBLESHOOTING 12

REFERENCES 13

Maintenance More information

INSTALLATION/ CONNECTION 14

SPECIFICATIONS 17

IMPORTANT

•

To ensure proper use, please read through this manual before using this product. It is especially important that you read and observe

Warning and Caution in this manual.

•

Please keep the manual in a safe and accessible place for future reference.

WARNING

•

Do not operate any function that takes your attention away from safe driving.

•

Do not ingest the battery, Chemical Burn Hazard

The remote control supplied with this product contains a coin/button cell battery. If the coin/button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death. Keep new and used batteries away from children. If the battery compartment does not close securely, stop using the product and keep it away from children. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.

Caution

Volume setting:

•

Adjust the volume so that you can hear sounds outside the car to prevent accidents.

•

Lower the volume before playing digital sources to avoid damaging the speakers by the sudden increase of the output level.

General:

•

Avoid using the external device if it might hinder safe driving.

•

Make sure all important data has been backed up. We shall bear no responsibility for any loss of recorded data.

•

Never put or leave any metallic objects (such as coins or metal tools) inside the unit, to prevent a short circuit.

•

Depending on the types of cars, the antenna will automatically extend when you turn on the unit with the antenna control wire connected

( 16)

. Turn off the unit or change the source to STANDBY when parking at a low ceiling area.

Remote control (RC-406):

•

Do not leave the remote control in hot places such as on the dashboard.

•

The Lithium battery is in danger of explosion if replaced incorrectly. Replace it only with the same or equivalent type.

•

The battery pack or batteries shall not be exposed to excessive heat such as sunshine, fire or the like.

How to read this manual

•

Operations are explained mainly using buttons on the faceplate.

•

English indications are used for the purpose of explanation. You can select the display language from the

•

[XX]

indicates the selected items.

•

( XX)

indicates references are available on the stated page.

[FUNCTION]

menu.

( 5)

ENGLISH

BASICS

Faceplate

Remote control (RC-406)

Volume knob

Detach button

To On the faceplate On the remote control

Turn on the power

Adjust the volume Turn the volume knob. Press

Select a source

Change the display information* Press DISP repeatedly.

You can also turn off the display information by pressing

Press

• Press and hold to turn off the power.

Press

Display window

How to resetAttach Detach

repeatedly.

DISP

repeatedly.

Your preset adjustments will be erased except stored radio stations.

( 14)

Not used

How to replace the battery

Press and hold SRC to turn off the power. ( Pressing SRC does not turn on the power. )

• Press and hold the volume to 15.

Press ATT during playback to attenuate the sound.

• Press again to cancel.

Press SRC repeatedly.

( Not available )

or .

Remote sensor (Do not expose to bright sunlight.)

Pull out the insulation sheet when using for the first time.

to continuously increase

ENGLISH

GETTING STARTED

Select the display language and cancel the demonstration

When you turn on the power (or after you reset the unit), the display shows: “SEL LANGUAGE”

1 Turn the volume knob to select

then press the knob.

[ENG]

is selected for the initial setup.

Then, the display shows: “CANCEL DEMO”

KNOB”.

2 Press the volume knob.

[YES]

is selected for the initial setup.

3 Press the volume knob again.

“DEMO OFF” appears.

Set the clock and date

Press the volume knob to enter

2 Turn the volume knob to select

To adjust the clock

3 Turn the volume knob to select 4 Turn the volume knob to make the settings, then press the knob.

Hour

Minute

5 Turn the volume knob to select 6 Turn the volume knob to select

“PRESS” “VOLUME KNOB”

[ENG]

(English) or

“PRESS” “VOLUME

[FUNCTION] [CLOCK]

[CLOCK ADJUST]

[CLOCK FORMAT] [12H]

, then press the knob.

[24H]

, then press the knob.

[SPA]

(Spanish),

To set the date

7 Turn the volume knob to select 8 Turn the volume knob to select

the knob.

9 Turn the volume knob to select

[DATE FORMAT] [DD/MM/YY]

[DATE SET]

, then press the knob.

[MM/DD/YY]

, then press

10 Turn the volume knob to make the settings, then press the knob.

Day

Month Year or Month Day Year

11 Press and hold to exit.

To return to the previous setting item, press

Set the initial settings

Press repeatedly to enter STANDBY.

2 Press the volume knob to enter

[FUNCTION]

3 Turn the volume knob to select an item (see the following table),

then press the knob.

4 Repeat step 3 until the desired item is selected or activated. 5 Press and hold to exit.

To return to the previous setting item, press

AUDIO CONTROL

SWITCH PREOUT

SP SELECT

REAR/SUB-W

connected to the line out terminals on the rear (through an external amplifier).

OFF/5/4/6 × 9/6/OEM

or 4inches, 6×9inches or 6inches) or OEM speakers for optimum performance.

: Selects whether rear speakers or a subwoofer are

( 16)

: Selects according to the speaker size (5inches

Default:

ENGLISH

GETTING STARTED RADIO

TUNER SETTING

PRESET TYPE

SYSTEM

KEY BEEP

SOURCE SELECT

BUILT-IN AUX

F/W UPDATE

UPDATE SYSTEM

F/W UP xxxx

CLOCK

CLOCK DISPLAY

ENGLISH

ESPANOL

NORMAL

:Memorizes one station for each preset button in each band (FM1/FM2/FM3/AM).; button, regardless of the selected band.

:Activates the keypress tone.;

:Enables AUX in source selection.;

YES

:Starts upgrading the firmware.; NO:Cancels (upgrading is not activated). For details on how to update the firmware, visit <www.kenwood.com/cs/ce/>.

:The clock time is shown on the display even when the unit is turned

off.;

OFF

:Cancels.

Select the display language for if applicable. By default,

[ENGLISH]

MIX

:Memorizes one station for each preset

OFF

:Deactivates.

OFF

:Disables.

[FUNCTION]

is selected.

menu and music information

( 9)

Search for a station

Press repeatedly to select TUNER.

2 Press repeatedly (or press / on the remote

control) to select FM1/FM2/FM3/AM.

3 Press S/T (or press S/ on the remote control) to

search for a station.

• To change the searching method for S/T: Press

repeatedly.

AUTO1 : Automatically search for a station. AUTO2 : Search for a preset station. MANUAL : Manually search for a station.

• To store a station: Press and hold one of the number buttons (1to6).

• To select a stored station: Press one of the number buttons (1to6) (or

press one of the number buttons (1to6) on the remote control).

Direct Access Tuning

1 Press DIRECT to enter Direct Access Tuning. 2 Press the number buttons to enter a frequency. 3 Press to search for a station.

• To cancel, press

• If no operation is done for 10seconds after step is automatically canceled.

(using the remote control)

or DIRECT.

2, Direct Access Tuning

ENGLISH

RADIO

Other settings

Press the volume knob to enter

[FUNCTION]

2 Turn the volume knob to select an item (see the following table),

then press the knob.

3 Repeat step 2 until the desired item is selected or activated. 4 Press and hold to exit.

[PRESET TYPE]. ( 5)

OFF

:Cancels.

Default:

ENGLISH/FRENCH

To return to the previous setting item, press

TUNER SETTING

AUTO MEMORY

MONO SET

NEWS SET ON

REGIONAL ON

AF SET ON

TI ON

PTY SEARCH1 Turn the volume knob to select the available Program Type, then press

YES

:Automatically starts memorizing 6 stations with good reception.;

:Cancels.

•

Selectable only if

:Improves the FM reception, but the stereo effect may be lost.;

OFF

:Cancels.

: The unit will temporarily switch to News Programme if available. ;

OFF

:Cancels.

: Switches to another station only in the specific region using the “AF”

control.;

: Automatically searches for another station broadcasting the same program in the same Radio Data System network with better reception when the current reception is poor.;

:Allows the unit to temporarily switch to Traffic Information if available (“TI” lights up).;

the knob.

Turn the volume knob to select the PTY language (

GERMAN

Press S/T to start searching.

[NORMAL]

OFF

:Cancels.

OFF

:Cancels.

), then press the knob.

is selected for

CLOCK

TIME SYNC

Available Program Type for

SPEECH

MUSIC

The unit will search for the Program Type categorized under

[MUSIC]

•

[MONO SET]/[NEWS SET]/[REGIONAL]/[AF SET]/[TI]/[PTY SEARCH]

only when the band is FM1/FM2/FM3.

• If the volume is adjusted during reception of traffic information or news bulletin, the adjusted volume is memorized automatically. It will be applied the next time traffic information or news bulletin is turned on.

:Synchronizes the unit’s time to the Radio Data System station time.;

OFF

:Cancels.

NEWS, AFFAIRS, INFO CULTURE, SCIENCE, VARIED, WEATHER, FINANCE, CHILDREN, SOCIAL RELIGION, PHONE IN, TRAVEL, LEISURE, DOCUMENT

POP M

(music),

CLASSICS, OTHER M OLDIES, FOLK M

if selected.

[PTY SEARCH]

(information),

ROCK M

(music),

(music)

SPORT, EDUCATE, DRAMA

(music),

EASY M

JAZZ, COUNTRY, NATION M

(music),

LIGHT M

(music),

is selectable

(music),

[SPEECH]

ENGLISH

USB/iPod/ANDROID

Start playback

The source changes automatically and playback starts.

USB input terminal

USB

CA-U1EX (max.: 500mA) (optional accessory)

iPod/iPhone

KCA-iP102/KCA-iP103 (optional accessory) or accessory of the iPod/

iPhone

ANDROID

Micro USB 2.0 cable (commercially available)

KCA-iP102 : 30-pin type, KCA-iP103 : Lightning type

Do not leave the cable inside the car when not using.

To directly select USB/iPod/ANDROID source, press iPodUSB.

To On the faceplate On the remote control

Playback/pause Press .

Reverse/Fast-forward

Select a file

Select a folder

Repeat play

Press and hold S/T. Press and hold S/ .

Press S/T. Press S/

Press J/K. Press repeatedly.

FILE REPEAT/FOLDER REPEAT/ALL REPEAT FILE REPEAT/FOLDER REPEAT/REPEAT OFF

Random play

Press repeatedly.

FOLDER RANDOM/RANDOM OFF

Press

/ .

: MP3/WMA/WAV/FLAC file : iPod or ANDROID

: MP3/WMA/WAV/FLAC file, iPod or

ANDROID

Press and hold

When connecting an Android device, “Press [VIEW] to install KENWOOD MUSIC PLAY APP” is shown. Follow the instructions

to select

ALL RANDOM

to install the application. You can also install the latest version of KENWOOD MUSIC PLAY application on your Android device before connecting. For more information, visit <www.kenwood.com/cs/ce/>.

For ANDROID: Applicable only when

Only for MP3/WMA/WAV/FLAC files. This does not work for iPod/ANDROID.

For iPod/ANDROID: Applicable only when

[BROWSE MODE]

is selected.

[MODE OFF]/[BROWSE MODE]

( 8)

is selected.

( 8)

ENGLISH

USB/iPod/ANDROID

Select control mode

While in iPod source, press iPodUSB repeatedly.

MODE ON

: Control iPod using the iPod itself

MODE OFF

While in ANDROID source, press iPodUSB repeatedly.

BROWSE MODE

HAND MODE

play/pause, file skip, fast-forward or reverse from this unit.

: Control iPod from this unit.

: Control Android device from this unit via KENWOOD

MUSIC PLAY application installed in the Android device.

: Control Android device using the Android device

itself via other media player applications installed in the Android device. However, you can still play/pause and file skip from this unit.

. However,

you can still

Select music drive

While in USB source, press iPodUSB repeatedly.

Stored songs in the following drive will be played back.

• Selected internal or external memory of a smartphone (Mass Storage Class).

• Selected drive of a multiple drives device.

Select a file from a folder/list

For iPod/ANDROID, applicable only when is selected.

[MODE OFF]/[BROWSE MODE]

1 Press . 2 Turn the volume knob to select a folder/list, then press the

knob.

3 Turn the volume knob to select a file, then press the knob.

Quick Search

If you have many files, you can search through them quickly.

Turn the volume knob quickly to browse through the list quickly.

Skip Search

Press S/T to search at a preset skip search ratio.

• Pressing and holding S/T searches at a 10% ratio.

Alphabet search

You can search for a file according to the first character.

For iPod source

(applicable only for USB and ANDROID source)

(applicable only for iPod and ANDROID source)

1 Turn the volume knob quickly to enter character search. 2 Turn the volume knob to select the character.

• Select “ 3 Press S/T to move to the entry position.

” to search for a character other than AtoZ, 0to9.

• You can enter up to 3characters. 4 Press the volume knob to start searching.

For ANDROID source

1 Press J/K to enter character search. 2 Turn the volume knob to select the character.

^A^: Upper case letters (A to Z) _A_: Lower case letters (a to z)

-0-: Numbers (0 to 9)

: Character other than AtoZ, 0to9

***

3 Press the volume knob to start searching.

• To return to the root folder/first file/top menu, press 5.

• To return to the previous setting item, press

• To cancel, press and hold

( 9, [SKIP SEARCH])

ENGLISH

USB/iPod/ANDROID

Direct Music Search

1 Press DIRECT. 2 Press the number buttons to enter a file number. 3 Press to search for music.

• To cancel, press

• Not available if Random Play is selected.

• Not applicable for iPod and ANDROID source.

Listen to TuneIn Radio/TuneIn Radio Pro/Aupeo

While listening to TuneIn Radio, TuneIn Radio Pro or Aupeo, connect the iPod/iPhone to the USB input terminal of the unit.

• The unit will output the sound from these applications.

Other settings

Press the volume knob to enter

2 Turn the volume knob to select an item (see the following table),

then press the knob.

3 Repeat step 2 until the desired item is selected or activated. 4 Press and hold to exit.

To return to the previous setting item, press

USB

MUSIC DRIVE DRIVE CHANGE

SKIP SEARCH 0.5%/1%/5%/10%

(using the remote control)

or DIRECT.

[FUNCTION]

automatically and playback starts. Repeat steps

the skip search ratio over the total files.

:The next drive (

to 3 to select the following drives.

[DRIVE 1]

: While listening to iPod or ANDROID source, selects

Default:

[DRIVE 5]

) is selected

AUX

Preparation:

Select

[ON]

for

[BUILT-IN AUX]

Start listening

Connect a portable audio player (commercially available).

Auxiliary input jack

3.5mm (1/8") stereo mini plug with “L” shaped connector (commercially available)

2 Press repeatedly to select AUX. 3 Turn on the portable audio player and start playback.

Set the AUX name

While listening to a portable audio player connected to the unit...

1 Press the volume knob to enter 2 Turn the volume knob to select 3 Turn the volume knob to select 4 Turn the volume knob to select an item, then press the knob.

AUX

(default)/

DVD/PORTABLE/GAME/VIDEO/TV

5 Press and hold to exit.

To return to the previous setting item, press

[SOURCE SELECT]. ( 5)

Portable audio player

[FUNCTION] [SYSTEM] [AUX NAME SET]

, then press the knob.

ENGLISH

AUDIO SETTINGS

While listening to any source...

1 Press the volume knob to enter 2 Turn the volume knob to select an item (see the following

table), then press the knob.

3 Repeat step 2 until the desired item is selected or

activated.

4 Press and hold to exit.

To return to the previous setting item, press

(or using the remote control)

1 Press AUD to enter

[AUDIO CONTROL]

2 Press J / K to select an item, then press .

AUDIO CONTROL

SUB-W LEVEL

BASS LEVEL –8

MID LEVEL –8

TRE LEVEL –8

–15

to +8 (+2)

to +8 (+1)

+15 (0

[FUNCTION]

) Adjusts the subwoofer output level.

Adjusts the level to memorize for each source. (Before making an adjustment, select the source you want to adjust.)

Default:

EQ PRO

(This setting is stored to

BASS ADJUST BASS CTR FRQ 60/80/100/200

MID ADJUST MID CTR FRQ 0.5KHZ/1.0KHZ/1.5KHZ/2.5KHZ

TRE ADJUST TRE CTR FRQ 10.0KHZ/12.5KHZ/15.0KHZ/17.5KHZ

PRESET EQ DRIVE EQ/TOP40/POWERFUL/ROCK/POPS/EASY/JAZZ/NATURAL/USER

BASS BOOST LV1/LV2/LV3

LOUDNESS LV1/LV2

SUBWOOFER SET ON

LPF SUBWOOFER THROUGH

SUB-W PHASE REVERSE

[USER]

: Selects the center frequency.

BASS LEVEL –8

BASS Q FACTOR 1.00/1.25/1.50/2.00

BASS EXTEND ON

MID LEVEL –8

MID Q FACTOR 0.75/1.00/1.25

TRE LEVEL –8

Selects a preset equalizer suitable to the music genre. (Select settings made in

[DRIVE EQ]

of the tyres.

:Selects your preferred low and high frequencies boost to produce a well-

balanced sound at a low volume level.;

:Turns on the subwoofer output.;

signals with frequencies lower than 85Hz/120Hz/160Hz are sent to the subwoofer.

(180°)/ line with the speaker output for optimum performance. (Selectable only if a setting other than

to +8 (+2):Adjusts the level.

:Adjusts the quality factor.

:Turns on the extended bass.;

to +8 (+1):Adjusts the level.

:Adjusts the quality factor.

frequency.

to +8 (+1):Adjusts the level.

[EQ PRO]

is a preset equalizer that reduces noise outside the car or running noise

:Selects your preferred bass boost level.;

:All signals are sent to the subwoofer.;

[THROUGH]

OFF

NORMAL

(0°):Selects the phase of the subwoofer output to be in

is selected for

[LPF SUBWOOFER]

OFF

:Selects the center frequency.

:Cancels.

85HZ/120HZ/160HZ

:Cancels.

:Selects the center

[USER]

OFF

:Cancels.

to use the

:Audio

ENGLISH

AUDIO SETTINGS

DISPLAY SETTINGS

FADER R15

BALANCE L15

VOLUME OFFSET

SOUND RECNSTR

(Sound reconstruction)

•

[SUB-W LEVEL]/[SUBWOOFER SET]/[LPF SUBWOOFER]/[SUB-W PHASE]

selectable only if

•

[SUB-W LEVEL]/[LPF SUBWOOFER]/[SUB-W PHASE] [SUBWOOFER SET]

F15 (0

):Adjusts the rear and front speaker output balance.

R15 (0

):Adjusts the left and right speaker output balance.

For AUX:

–8

to +8(0) ; For other sources: –8 to 0:Preset the initial volume level of each source. (Before adjustment, select the source you want to adjust.)

:Creates realistic sound by compensating the high-frequency components and restoring the rise-time of the waveform that are lost in audio data compression.;

[SWITCH PREOUT]

is set to

[ON]. ( 10)

OFF

is set to

:Cancels.

[SUB-W]. ( 4)

is selectable only if

Set the dimmer

Press and hold DISP (DIMMER) to turn on or off the dimmer.

• If you have set hold this button.

[DIMMER TIME]

, it will be canceled once you press and

Other settings

Press the volume knob to enter

[FUNCTION]

2 Turn the volume knob to select an item (see the following table),

then press the knob.

3 Repeat step 2 until the desired item is selected/activated or follow

the instructions stated on the selected item.

4 Press and hold to exit.

To return to the previous setting item, press

DISPLAY

DIMMER

BRIGHTNESS 0

TEXT SCROLL AUTO/ONCE

Dim the illumination.

:Dimmer is turned on.;

DIMMER TIME

Turn the volume knob to adjust the

(Default:

[ON]: 6:00PM; [OFF]: 6:00 AM

to 31: Select your preferred brightness level for display illumination.

automatically, or scroll only once.;

:Select whether to scroll the display information

OFF

:Set the dimmer on and off time.

:Cancels.

[ON]

time, then press the knob.

[OFF]

time, then press the knob.

)

OFF

:Cancels.

Default:

ENGLISH

TROUBLESHOOTING

Symptom Remedy

Sound cannot be heard.

“MISWIRING CHECK WIRING THEN PWR ON” appears.

“PROTECTING SEND SERVICE” appears.

General

•

Sound cannot be heard.

•

The unit does not turn on.

•

Information shown on the

display is incorrect.

The unit does not work at all. Reset the unit.

•

Radio reception is poor.

•

Static noise while listening

Radio

to the radio.

“READING” keeps flashing. Do not use too many hierarchical levels or folders.

Elapsed playing time is not correct.

Correct characters are not displayed (e.g. album name).

USB/iPod

“NA FILE” Make sure the media contains supported audio files.

“READ ERROR” Copy the files and folders onto the USB device again.

•

Adjust the volume to the optimum level.

•

Check the cords and connections.

Turn the power off, then check to be sure the terminals of the speaker wires are insulated properly. Turn the power on again.

Send the unit to the nearest service center.

Clean the connectors.

Connect the antenna firmly.

This is caused by how the files are recorded.

•

This unit can only display uppercase letters,

numbers, and a limited number of symbols.

•

Depending on the display language you have

selected displayed correctly.

( 13)

If this does not solve the problem, reset the USB device or use another USB device.

( 13)

( 3)

( 5)

, some characters may not be

Symptom Remedy

“NO DEVICE” Connect a USB device, and change the source to USB again.

“COPY PRO” A copy-protected file is played.

“NA DEVICE” Connect a supported USB device, and check the

USB/iPod

“NO MUSIC” Connect a USB device that contains playable audio files.

“iPod ERROR”

•

Sound cannot

be heard during playback.

•

Sound output only

from the Android device.

Cannot playback at [

BROWSE MODE

ANDROID

“NO DEVICE” or “READING” keeps flashing.

Playback is intermittent or sound skips.

“ANDROID ERROR”/ “NADEVICE”

connections.

•

Reconnect the iPod.

•

Reset the iPod.

•

Reconnect the Android device.

•

If in

[HAND MODE]

on the Android device and start playback.

•

If in

[HAND MODE]

application or use another media player application.

•

Restart the Android device.

•

If this does not solve the problem, the connected Android

device is unable to route the audio signal to unit.

•

Make sure KENWOOD MUSIC PLAY APP is installed on the

Android device.

•

Reconnect the Android device and select the appropriate

control mode.

•

If this does not solve the problem, the connected Android

device does not support

•

Switch off the developer options on the Android device.

•

Reconnect the Android device.

•

If this does not solve the problem, the connected Android

device does not support

Turn off the power saving mode on the Android device.

•

Reconnect the Android device.

•

Restart the Android device.

, launch any media player application

, relaunch the current media player

( 7)

[BROWSE MODE]. ( 13)

( 13)

ENGLISH

REFERENCES

Maintenance

Cleaning the unit

Wipe off dirt on the faceplate with a dry silicone or soft cloth.

Cleaning the connector

Detach the faceplate and clean the connector gently with a cotton swab, being careful not to damage the connector.

More information

For: – Latest firmware updates and latest compatible item list

– Any other latest information

Visit <www.kenwood.com/cs/ce/>.

Playable files

•

Playable audio file for USB mass storage class device: MP3 (.mp3), WMA (.wma),

WAV (.wav), FLAC (.flac)

•

Playable USB device file system: FAT12, FAT16, FAT32

Even when audio files comply with the standards listed above, playback may be impossible depending on the types or conditions of media or device.

•

For detailed information and notes about the playable audio files, visit

<www.kenwood.com/cs/ce/audiofiles>.

About USB devices

•

You cannot connect a USB device via a USB hub.

•

Connecting a cable whose total length is longer than 5m may result in abnormal playback.

•

This unit cannot recognize a USB device whose rating is other than 5V and exceeds 1A.

Connector (on the reverse side of the faceplate)

About iPod/iPhone

Made for

–

iPod touch (2nd, 3rd, 4th, 5th, and 6th generation)

–

iPod classic

–

iPod nano (3rd, 4th, 5th, 6th, and 7th generation)

–

iPhone 3G, 3GS, 4, 4S, 5, 5S, 5C, 6, 6 Plus, 6S, 6S Plus, SE

•

You cannot operate iPod if “KENWOOD” or “ ” is displayed on iPod.

•

Depending on the version of the operating system of the iPod/iPhone, some functions may

not operate on this unit.

About Android device

•

This unit supports Android OS 4.1 and above.

•

Some Android devices (with OS 4.1 and above) may not fully support Android Open Accessory

(AOA) 2.0.

•

If the Android device supports both mass storage class device and AOA 2.0, this unit always

playback via AOA 2.0 as priority.

Muting upon the reception of a phone call

Connect the MUTE wire to your telephone using a commercial telephone accessory.

When a call comes in, “CALL” appears.

•

To continue listening to the audio system during a call, press . “CALL” disappears

and the audio system resumes.

When the call ends, “CALL” disappears.

(The audio system pauses.)

(The audio system resumes.)

( 16)

ENGLISH

REFERENCES

Change the display information

Each time you press

•

If the information is unavailable or not recorded, “NO TEXT”, “NO INFO”, or other information

(eg. station name, playing time) appears.

Source name Display information

STANDBY Source name (*) Clock (back to the beginning)

TUNER Frequency

USB

iPod or ANDROID When

AUX Source name

Turn off the display information.

DISP

, the display information changes.

(*) Clock (back to the beginning)

(For FM Radio Data System stations only)

Station name (*) Radio text Radio text+ Title/Artist Frequency

(For MP3/WMA/WAV/FLAC files)

Music title/Artist (*) Album title/artist Folder name File name

Music title/Artist (*) Album title/Artist Playing time Clock

Clock (back to the beginning)

Playing time Clock (back to the beginning)

[MODE OFF]/[BROWSE MODE]

(back to the beginning)

(*) Clock (back to the beginning)

is selected.

( 8)

INSTALLATION/CONNECTION

Warning

•

The unit can only be used with a 12V DC power supply, negative ground.

•

Disconnect the battery’s negative terminal before wiring and mounting.

•

Do not connect Battery wire (yellow) and Ignition wire (red) to the car chassis or Ground wire

(black) to prevent a short circuit.

•

Insulate unconnected wires with vinyl tape to prevent a short circuit.

•

Be sure to ground this unit to the car’s chassis again after installation.

Caution

•

For safety’s sake, leave wiring and mounting to professionals. Consult the car audio dealer.

•

Install this unit in the console of your vehicle. Do not touch the metal parts of this unit during

and shortly after use of the unit. Metal parts such as the heat sink and enclosure become hot.

•

Do not connect the [ wires of speakers to the car chassis or Ground wire (black), or connect

them in parallel.

•

Mount the unit at an angle of less than 30º.

•

If your vehicle wiring harness does not have the ignition terminal, connect Ignition wire (red)

to the terminal on the vehicle’s fuse box which provides 12 V DC power supply and is turned on and off by the ignition key.

•

Keep all cables away from heat dissipate metal parts.

•

After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. on the car are

working properly.

•

If the fuse blows, first make sure the wires are not touching car’s chassis, then replace the old

fuse with one that has the same rating.

Basic procedure

Remove the key from the ignition switch, then disconnect the [ terminal of the car

battery.

Connect the wires properly.

See Wiring connection.

Install the unit to your car.

See Installing the unit (in-dash mounting).

Connect the [ terminal of the car battery.

Reset the unit.

( 16)

( 15)

( 3)

ENGLISH

INSTALLATION/CONNECTION

Installing the unit (in-dash mounting) When installing without the mounting sleeve

Remove the mounting sleeve and trim plate from the unit.

Align the holes in the unit (on both sides) with the

vehicle mounting bracket and secure the unit with screws (supplied).

Use only the specified screws. Using wrong screws might

damage the unit.

How to remove the unit

Detach the faceplate.

Remove the trim plate.

Insert the extraction keys deeply into the slots on each side,

then follow the arrows as shown on the illustration.

Orientate the trim plate as illustrated before fitting.

Part list for installation

(A)

Faceplate

(D)

Wiring harness

Hook on the top side

(B)

Trim plate

(E)

Extraction key

Do the required wiring.

( 16)

Dashboard of your car

Bend the appropriate tabs to hold the mounting sleeve firmly in place.

(C)

Mounting sleeve

(F)

Screws

ENGLISH

INSTALLATION/CONNECTION

Wiring connection

IMPORTANT:

commercially available custom wiring harness specific for your car and leave this job to professionals for your safety. Consult your car audio dealer.

When connecting to an external amplifier, connect its ground wire to the car’s chassis to avoid damaging the unit.

We recommend installing the unit with a

Output terminals

Antenna terminal

Fuse (10A)

Battery

Ignition switch

Car fuse box

ENGLISH

To front speaker (left)

To front speaker (right)

To rear speaker (left)

To rear speaker (right)

Car fuse box

Black (Ground wire)

To the metallic body or chassis of the car

Purple/Black

Red (Ignition wire)

Yellow (Battery wire)

White

White/Black

Gray

Gray/Black

Green

Green/Black

Purple

If no connections are made, do not let the wire come out from the tab.

Brown (Mute control wire)

Blue/White (Power control wire/

Antenna control wire)

350 mA)

(12 V

Light blue/yellow (Steering remote

control wire)

To the terminal that is grounded when the telephone rings or during conversation.

( 13)

(To connect the Kenwood navigation system, refer your navigation manual.)

To the power control terminal when using the optional power amplifier or to the antenna control terminal in the vehicle

To the steering wheel remote control adapter

+ 36 hidden pages