Kenwood KMM-115 User Manual [es]

KMM-115

DIGITAL MEDIA RECEIVER

INSTRUCTION MANUAL

RÉCEPTEUR MULTIMÉDIA NUMÉRIQUE

MODE D’EMPLOI

RECEPTOR DE MEDIOS DIGITALES

MANUAL DE INSTRUCCIONES

For your records

Record the serial number, found on the back of the unit, in the spaces designated on the warranty card, and in the space provided below. Refer to the model and serial numbers whenever you call upon your Kenwood dealer for information or service on the product. Model KMM-115 Serial number

US Residents Only

CONTENTS BEFORE USE

BEFORE USE 2

BASICS 3

GETTING STARTED 4

1 Select the display language

and cancel the demonstration 2 Set the clock and date 3 Set the initial settings

RADIO 5

USB / iPod / ANDROID 7

AUX 9

AUDIO SETTINGS 10

DISPLAY SETTINGS 11

TROUBLESHOOTING 11

REFERENCES 12

Maintenance More information

INSTALLATION / CONNECTION 14

SPECIFICATIONS 16

IMPORTANT

• To ensure proper use, please read through this manual before using this product. It is especially important that you read and observe Warning and Caution in this manual.

• Please keep the manual in a safe and accessible place for future reference.

Warning

Do not operate any function that takes your attention away from safe driving.

Caution

Volume setting:

• Adjust the volume so that you can hear sounds outside the car to prevent accidents.

• Lower the volume before playing digital sources to avoid damaging the speakers by the sudden increase of the output level.

General:

• Avoid using the external device if it might hinder safe driving.

• Make sure all important data has been backed up. We shall bear no responsibility for any loss of recorded data.

• Never put or leave any metallic objects (such as coins or metal tools) inside the unit to prevent a short circuit.

• Depending on the types of cars, the antenna will automatically extend when you turn on the unit with the antenna control wire connected ( a low ceiling area.

Remote control (RC-406):

• Do not leave the remote control in hot places such as on the dashboard.

• The Lithium battery is in danger of explosion if replaced incorrectly. Replace it only with the same or equivalent type.

• The battery pack or batteries shall not be exposed to excessive heat such as sunshine, fire or the like.

• Keep the battery out of reach of children and in its original packaging when not in used. Dispose of used batteries promptly. If swallowed, contact a physician immediately.

How to read this manual

• Operations are explained mainly using buttons on the faceplate.

• English indications are used for the purpose of explanation. You can select the display language from the [

FUNCTION

• [

• (

] menu. ( 5)

] indicates the selected items.

XX) indicates references are available on the stated page.

15). Turn off the unit or change the source to STANDBY when parking at

BASICS

Faceplate

Remote control (RC-406)

Volume knob

Detach button

To On the faceplate On the remote control

Turn on the power

Adjust the volume Turn the volume knob. Press

Select a source

Change the display information* Press DISP repeatedly. (

You can also turn off the display information by pressing

Display window

How to resetAttach Detach

Your preset adjustments will be erased except stored radio stations.

DISP

repeatedly.

13) ( Not available )

repeatedly.

Press

• Press and hold to turn off the power.

Press

Not used

How to replace the battery

Press and hold SRC to turn off the power. ( Pressing SRC does not turn on the power. )

or .

Press ATT during playback to attenuate the sound.

• Press again to cancel.

Press SRC repeatedly.

Remote sensor (Do not expose to bright sunlight.)

Pull out the insulation sheet when using for the first time.

ENGLISH

GETTING STARTED

Select the display language and cancel the demonstration

When you turn on the power (or after you reset the unit), the display shows: “SEL LANGUAGE”

1 Turn the volume knob to select [

then press the knob.

[

ENG

] is selected for the initial setup.

Then, the display shows: “CANCEL DEMO”

KNOB”.

2 Press the volume knob.

[

YES

] is selected for the initial setup.

3 Press the volume knob again.

“DEMO OFF” appears.

Set the clock and date

Press the volume knob to enter [

1 2 Turn the volume knob to select [

To adjust the clock

3 Turn the volume knob to select [ 4 Turn the volume knob to make the settings, then press the knob.

Hour

Minute

5 Turn the volume knob to select [ 6 Turn the volume knob to select [

“PRESS” “VOLUME KNOB”

ENG

] (English) or [

“PRESS” “VOLUME

FUNCTION

CLOCK

], then press the knob.

CLOCK ADJUST

CLOCK FORMAT 12H

], then press the knob.

] or [

24H

], then press the knob.

SPA

] (Spanish),

To set the date

7 Turn the volume knob to select [ 8 Turn the volume knob to select [

the knob.

9 Turn the volume knob to select [

DATE FORMAT DD/MM/YY

DATE SET

], then press the knob.

] or [

], then press the knob.

MM/DD/YY

], then press

10 Turn the volume knob to make the settings, then press the knob.

Day

Month Year or Month Day Year

11 Press and hold to exit.

To return to the previous setting item, press .

Set the initial settings

Press repeatedly to enter STANDBY.

1 2 Press the volume knob to enter [

FUNCTION

3 Turn the volume knob to select an item (see the following table),

then press the knob.

4 Repeat step 3 until the desired item is selected or activated. 5 Press and hold to exit.

To return to the previous setting item, press .

Default:

AUDIO CONTROL

SWITCH PREOUT

SP SELECT OFF/ 5/4/ 6 × 9/6/ OEM

REAR/ SUB-W

connected to the line out terminals on the rear (through an external amplifier).

or 4inches, 6×9inches or 6inches) or OEM speakers for optimum performance.

: Selects whether rear speakers or a subwoofer are

: Selects according to the speaker size (5inches

GETTING STARTED RADIO

TUNER SETTING

PRESET TYPE

SYSTEM

KEY BEEP

SOURCE SELECT

BUILT-IN AUX

F/W UPDATE

UPDATE SYSTEM

F/W UP xx.xx

CLOCK

CLOCK DISPLAY

ENGLISH

ESPANOL

NORMAL

:Memorizes one station for each preset button in each band (FM1/ FM2/ FM3/ AM).; button, regardless of the selected band.

:Activates the keypress tone.;

:Enables AUX in source selection.;

YES

:Starts upgrading the firmware.; NO:Cancels (upgrading is not activated). For details on how to update the firmware, see: www.kenwood.com/cs/ce/

:The clock time is shown on the display even when the unit is turned

off.;

OFF

:Cancels.

Select the display language for [ information if applicable. By default, [

ENGLISH

MIX

:Memorizes one station for each preset

OFF

:Deactivates.

OFF

:Disables. ( 9)

FUNCTION

] menu and music

] is selected.

Search for a station

Press repeatedly to select TUNER.

1 2 Press repeatedly (or press / on RC-406) to

select FM1/ FM2/ FM3/ AM.

3 Press S/T (or press S/ on RC-406) to search for a

station.

• To change the searching method for S/T: Press

repeatedly.

AUTO1 : Automatically search for a station. AUTO2 : Search for a preset station. MANUAL : Manually search for a station.

• To store a station: Press and hold one of the number buttons (1to6).

• To select a stored station: Press one of the number buttons (1to6) (or

press one of the number buttons (1to6) on RC-406).

Direct Access Tuning (using RC-406)

Press DIRECT to enter Direct Access Tuning.

1 2 Press the number buttons to enter a frequency. 3 Press to search for a station.

• To cancel, press or DIRECT.

• If no operation is done for 10seconds after step is automatically canceled.

2, Direct Access Tuning

ENGLISH

RADIO

Other settings

Press the volume knob to enter [

FUNCTION

2 Turn the volume knob to select an item (see the following table), then press

the knob.

3 Repeat step 2 until the desired item is selected or activated. 4 Press and hold to exit.

To return to the previous setting item, press .

Default:

TUNER SETTING

AUTO MEMORY

MONO SET ON

NEWS SET ON

REGIONAL ON

AF SET ON

TI ON

PTY SEARCH

CLOCK

TIME SYNC

YES

:Automatically starts memorizing 6 stations with good reception.; NO:Cancels.

•

Selectable only if [

:Improves the FM reception, but the stereo effect may be lost.;

: The unit will temporarily switch to News Programme if available. ;

: Switches to another station only in the specific region using the “AF” control.;

OFF

:Cancels.

: Automatically searches for another station broadcasting the same program in the same Radio Data System network with better reception when the current reception is poor.;

OFF

:Allows the unit to temporarily switch to Traffic Information if available (“TI” lights up).;

Select the available Program Type (see the following), then, press S/T to start.

:Synchronizes the unit’s time to the Radio Data System station time.;

OFF

:Cancels.

OFF

:Cancels.

NORMAL

] is selected for [

PRESET TYPE

]. ( 5)

OFF

:Cancels.

OFF

: Cancels.

Available Program Type

SPEECH : NEWS, AFFAIRS, INFO

DRAMA, CULTURE, SCIENCE, VARIED, WEATHER, FINANCE CHILDREN, SOCIAL, RELIGION, PHONE IN, TRAVEL, LEISURE DOCUMENT

MUSIC

POP M

(music),

CLASSICS, OTHER M

NATION M

] or [

MUSIC

]/ [

(music),

NEWS SET

The unit will search for the Program Type categorized under

[

SPEECH

MONO SET

• [ selectable only when the band is FM1/ FM2/ FM3.

• If the volume is adjusted during reception of traffic information or news bulletin, the adjusted volume is memorized automatically. It will be applied the next time traffic information or news bulletin is turned on.

ROCK M

OLDIES, FOLK M

] if selected.

]/ [

REGIONAL

(information),

(music),

EASY M

(music),

]/ [

AF SET

SPORT, EDUCATE

(music),

JAZZ, COUNTRY

(music)

]/ [TI]/ [

PTY SEARCH

LIGHT M

] is

USB / iPod / ANDROID

Start playback

The source changes automatically and playback starts.

USB input terminal

USB

To directly select USB/ IPOD/ ANDROID source, press iPod USB.

CA-U1EX (max.: 500mA) (optional accessory)

iPod/iPhone

KCA-iP102 / KCA-iP103 (optional accessory) or accessory cable of the iPod/iPhone

ANDROID

Micro USB 2.0 cable

(commercially available)

KCA-iP102 : 30-pin type, KCA-iP103 : Lightning type

Do not leave the cable inside the car when not using.

To On the faceplate On the remote control

Playback / pause Press .

Reverse / Fast-forward

Select a file

Select a folder

Repeat play

Press and hold S/T. Press and hold S/ .

Press S/T. Press S/

Press J/K. Press repeatedly.

FILE REPEAT/ FOLDER REPEAT/ ALL REPEAT FILE REPEAT/ FOLDER REPEAT/ REPEAT OFF

Random play

Press repeatedly.

FOLDER RANDOM/ RANDOM OFF

Press

/ .

: MP3/WMA/WAV/FLAC file : iPod or ANDROID

: MP3/WMA/WAV/FLAC file, iPod or

ANDROID

Press and hold

When connecting an Android device, “Press [VIEW] to install KENWOOD MUSIC PLAY APP” is shown. Follow the instructions

to select

ALL RANDOM

to install the application. You can also install the latest version of KENWOOD MUSIC PLAY application on your Android device before connecting. (

For ANDROID: Applicable only when [

Only for MP3/WMA/WAV/FLAC files. This does not work for iPod/ ANDROID.

For iPod/ ANDROID: Applicable only when [

12)

BROWSE MODE

MODE OFF

] is selected. ( 8)

]/ [

BROWSE MODE

] is selected. ( 8)

ENGLISH

USB / iPod / ANDROID

Select control mode

While in IPOD source, press iPod USB repeatedly.

MODE ON

: Control iPod using the iPod itself

still play/pause, file skip, fast-forward or reverse from

MODE OFF

While in ANDROID source, press iPod USB repeatedly.

BROWSE MODE

HAND MODE

this unit.

: Control iPod from this unit.

: Control Android device from this unit via

KENWOOD MUSIC PLAY application installed in the Android device.

: Control Android device using the Android device

itself via other media player applications installed in the Android device. However, you can still play/pause and file skip from this unit.

. However,

you can

Select music drive

Press iPod USB repeatedly.

Stored songs in the following drive will be played back.

• Selected internal or external memory of a smartphone (Mass Storage Class).

• Selected drive of a multiple drives device.

Listen to TuneIn Radio/ TuneIn Radio Pro/ Aupeo

While listening to TuneIn Radio, TuneIn Radio Pro or Aupeo, connect the iPod/iPhone to the USB input terminal of the unit.

• The unit will output the sound from these applications.

Select a file from a folder/list

Press .

1 2 Turn the volume knob to select a folder/list, then press the knob. 3 Turn the volume knob to select a file, then press the knob.

Quick Search

If you have many files, you can search through them quickly.

Turn the volume knob quickly to browse through the list quickly.

–

Not applicable for iPod.

(or)

Press S/T to search at a preset skip search ratio. (

• Pressing and holding S/T searches at a 10 –

Not applicable for MP3/WMA/WAV/FLAC files.

Alphabet Search

You can search for a file according to the first character.

(applicable only for iPod)

9, [SKIP SEARCH

ratio.

Turn the volume knob quickly to enter character search. Turn the volume knob to select the character.

To search for a character other than A to Z and 0to9, enter only “ * ”.

Press S/T to move to the entry position.

• You can enter up to 3characters.

Press the volume knob to start searching.

• To return to the root folder/ first file/ top menu, press 5.

• To return to the previous setting item, press

• To cancel, press and hold

• For iPod, applicable only when [

• For ANDROID, applicable only when [

MODE OFF

] is selected.

BROWSE MODE

] is selected.

])

USB / iPod / ANDROID

Direct Music Search (using RC-406)

Press DIRECT.

1 2 Press the number buttons to enter a file number. 3 Press to search for music.

• To cancel, press or DIRECT.

• Not available if Random Play is selected.

• Not applicable for iPod and ANDROID.

Other settings

Press the volume knob to enter [

1 2 Turn the volume knob to select an item (see the following table),

then press the knob.

3 Repeat step 2 until the desired item is selected or activated. 4 Press and hold to exit.

To return to the previous setting item, press .

USB

MUSIC DRIVE DRIVE CHANGE

SKIP SEARCH 0.5%/ 1%/ 5%/ 10%

automatically and playback starts. Repeat steps

skip search ratio over the total files.

FUNCTION

:The next drive ([

to 3 to select the following drives.

DRIVE 1

] to [

: While listening to iPod or ANDROID, selects the

DRIVE 5

Default:

]) is selected

AUX

Preparation:

Select [

] for [

BUILT-IN AUX

Start listening

Connect a portable audio player (commercially available).

Auxiliary input jack

3.5mm (1/8") stereo mini plug with “L” shaped connector (commercially available)

2 Press repeatedly to select AUX. 3 Turn on the portable audio player and start playback.

Set the AUX name

While listening to a portable audio player connected to the unit...

1 Press the volume knob to enter [ 2 Turn the volume knob to select [ 3 Turn the volume knob to select [ 4 Turn the volume knob to select an item, then press the knob.

AUX

(default)/

5 Press and hold to exit.

To return to the previous setting item, press .

]. ( 5)

Portable audio player

FUNCTION SYSTEM

], then press the knob.

AUX NAME SET

DVD/ PORTABLE/ GAME/ VIDEO/ TV

], then press the knob.

ENGLISH

AUDIO SETTINGS

While listening to any source...

1 Press the volume knob to enter [ 2 Turn the volume knob to select [ 3 Turn the volume knob to select an item (see the following table),

then press the knob.

4 Repeat step 3 until the desired item is selected or activated. 5 Press and hold to exit.

(or using RC-406)

1 Press AUD to enter [

AUDIO CONTROL

2 Press J / K to select an item, then press .

To return to the previous setting item, press

SUB-W LEVEL –15

BASS LEVEL –8

MID LEVEL –8

TRE LEVEL –8

EQ PRO

(This setting is stored to [

BASS ADJUST BASS CTR FRQ 60/ 80/ 100/ 200

MID ADJUST MID CTR FRQ 0.5K/ 1.0K/ 1.5K/ 2.5K

TRE ADJUST TRE CTR FRQ 10.0K/ 12.5K/ 15.0K/ 17.5K

+15 (0

) Adjusts the subwoofer output level.

to +8 (+2)

to +8 (+1)

USER

BASS LEVEL –8

BASS Q FACTOR 1.00/ 1.25/ 1.50/ 2.00

BASS EXTEND ON

MID LEVEL –8

MID Q FACTOR 0.75/ 1.00/ 1.25

TRE LEVEL –8

FUNCTION

AUDIO CONTROL

Adjusts the level to memorize for each source. (Before making an adjustment, select the source you want to adjust.)

].)

to +8 (+2):Adjusts the level.

:Turns on the extended bass.;

to +8 (+1):Adjusts the level.

frequency.

to +8 (+1):Adjusts the level.

], then press the knob.

: Selects the center frequency.

:Adjusts the quality factor.

OFF

:Cancels.

:Selects the center frequency.

:Adjusts the quality factor.

:Selects the center

Default:

PRESET EQ DRIVE EQ/ TOP40/ POWERFUL/ ROCK/ POPS/ EASY/ JAZZ

BASS BOOST LV1/ LV2/ LV3

LOUDNESS LV1/ LV2

SUBWOOFER SET ON

LPF SUBWOOFER THROUGH

SUB-W PHASE REVERSE

FADER R15

BALANCE L15

VOLUME OFFSET

SOUND RECNSTR

(Sound reconstruction)

• [

SUB-W LEVEL

selectable only if [

• [

SUB-W LEVEL

[

SUBWOOFER SET

NATURAL/ USER

genre. (Select [ [

DRIVE EQ

running noise of the tyres.

produce a well-balanced sound at a low volume level.;

:Turns on the subwoofer output.;

160HZ

160Hz are sent to the subwoofer.

output to be in line with the speaker output for optimum performance. (Selectable only if a setting other than [ selected for [

For AUX: volume level of each source. (Before adjustment, select the source you want to adjust.)

:Creates realistic sound by compensating the high-frequency components and restoring the rise-time of the waveform that are lost in audio data compression.;

]/ [

SUBWOOFER SET

SWITCH PREOUT

]/ [

LPF SUBWOOFER

] is set to [ON].

:Selects a preset equalizer suitable to the music

USER

] to use the settings made in [

] is a preset equalizer that reduces noise outside the car or

:Selects your preferred bass boost level.;

:Selects your preferred low and high frequencies boost to

OFF

:All signals are sent to the subwoofer.;

:Audio signals with frequencies lower than 85Hz/ 120Hz/

(180°)/

NORMAL

(0°):Selects the phase of the subwoofer

LPF SUBWOOFER

F15 (0

):Adjusts the rear and front speaker output balance.

R15 (0

):Adjusts the left and right speaker output balance.

–8

to +8(0) ; For other sources: –8 to 0:Preset the initial

]/ [

].)

OFF

:Cancels.

LPF SUBWOOFER

] is set to [

SUB-W PHASE

SUB-W

]/ [

] is selectable only if

:Cancels.

SUB-W PHASE

]. ( 4)

EQ PRO

].)

OFF

:Cancels.

OFF

:Cancels.

85HZ/ 120HZ

THROUGH

] is

DISPLAY SETTINGS

TROUBLESHOOTING

Set the dimmer

Press and hold DISP (DIMMER) to turn on or off the dimmer.

• If you have set [ press and hold this button.

DIMMER TIME

], it will be canceled once you

Other settings

Press the volume knob to enter [

1 2 Turn the volume knob to select [

knob.

FUNCTION DISPLAY

], then press the

3 Turn the volume knob to select an item (see the

following table), then press the knob.

4 Repeat step 3 until the desired item is selected/

activated or follow the instructions stated on the selected item.

5 Press and hold to exit.

To return to the previous setting item, press .

DIMMER

BRIGHTNESS 0

TEXT SCROLL AUTO/ ONCE

Dim the display illumination.

:Dimmer is turned on.;

DIMMER TIME

Turn the volume knob to adjust the [ON] time, then

press the knob.

Turn the volume knob to adjust the [

press the knob.

(Default: [

— 31: Select your preferred brightness level for display

illumination.

information automatically, or scroll only once.;

OFF

:Select whether to scroll the display

:Cancels.

OFF

:Set the dimmer on and off time.

6:00 PM

:Cancels.

OFF

; [

OFF

6:00 AM

)

] time, then

Default:

Symptom Remedy

Sound cannot be heard.

“MISWIRING CHECK WIRING THEN PWR ON” appears.

“PROTECTING SEND SERVICE” appears.

General

•

Sound cannot be heard.

•

The unit does not turn on.

•

Information shown on the

display is incorrect.

The unit does not work at all. Reset the unit. (

•

Radio reception is poor.

•

Static noise while listening

Radio

to the radio.

“READING” keeps flashing. Do not use too many hierarchical levels or folders.

Elapsed playing time is not correct.

Correct characters are not displayed (e.g. album name).

“NA FILE” Make sure the media contains supported audio files. ( “READ ERROR” Copy the files and folders onto the USB device again. If this does not

USB / iPod

“NO DEVICE” Connect a USB device, and change the source to USB again. “COPY PRO” A copy-protected file is played. “NA DEVICE” “NO MUSIC” Connect a USB device that contains playable audio files. “iPod ERROR”

•

Adjust the volume to the optimum level.

•

Check the cords and connections.

Turn the power off, then check to be sure the terminals of the speaker wires are insulated properly. Turn the power on again.

Send the unit to the nearest service center.

Clean the connectors. (

Connect the antenna firmly.

This is caused by how the tracks are recorded.

This unit can only display uppercase letters, numbers, and a limited number of symbols. (

solve the problem, reset the USB device or use another USB device.

Connect a supported USB device, and check the connections.

•

Reconnect the iPod.

•

Reset the iPod.

12)

3)

5)

12)

ENGLISH

TROUBLESHOOTING REFERENCES

Symptom Remedy

•

Sound cannot be heard

during playback.

•

Sound output only from

the Android device.

Cannot playback at [

BROWSE MODE

ANDROID

“NO DEVICE” or “READING” keeps flashing.

Playback is intermittent or sound skips.

“ANDROID ERROR” / “NADEVICE”

•

Reconnect the Android device.

•

If in [

application on the Android device and start playback.

•

If in [

player application or use another media player application.

•

Restart the Android device.

•

If this does not solve the problem, the connected

Android device is unable to route the audio signal to unit. (

•

Make sure KENWOOD MUSIC PLAY APP is installed

on the Android device. (

•

Reconnect the Android device and select the

appropriate control mode.

•

If this does not solve the problem, the connected

Android device does not support [

MODE

•

Switch off the developer options on the Android

device.

•

Reconnect the Android device.

•

If this does not solve the problem, the connected

Android device does not support [

MODE

Turn off the power saving mode on the Android device.

•

Reconnect the Android device.

•

Restart the Android device.

HAND MODE

13)

]. ( 13)

], launch any media player

], relaunch the current media

7)

BROWSE

Maintenance

Cleaning the unit

Wipe off dirt on the faceplate with a dry silicone or soft cloth.

Cleaning the connector

Detach the faceplate and clean the connector gently with a cotton swab, being careful not to damage the connector.

Connector (on the reverse side of the faceplate)

More information

Visit also the following website <www.kenwood.com/cs/ce/> for:

–

Latest firmware updates and latest compatible item list

–

Android™ application KENWOOD MUSIC PLAY

–

Any other latest information

General

Detailed information and notes about the playable audio files are stated in an online manual on the following website: www.kenwood.com/cs/ce/audiofile/

Playable files

•

Playable audio file: MP3 (.mp3), WMA (.wma), WAV (.wav), FLAC (.flac)

•

Playable USB device file system: FAT12, FAT16, FAT32 Even when audio files comply with the standards listed above, playback may be impossible depending on the types or conditions of media or device.

About USB devices

•

This unit can play MP3/WMA/WAV/FLAC files stored on a USB mass storage class device.

•

You cannot connect a USB device via a USB hub.

•

Connecting a cable whose total length is longer than 5m may result in abnormal playback.

•

This unit cannot recognize a USB device whose rating is other than 5V and exceeds 1A.

REFERENCES

About iPod/iPhone

Made for

iPod touch (2nd, 3rd, 4th, and 5th generation)

iPod classic

iPod nano (3rd, 4th, 5th, 6th, and 7th generation)

iPhone 3G, 3GS, 4, 4S, 5, 5S, 5C, 6, 6 Plus

•

You cannot operate iPod if “KENWOOD” or “ ” is displayed on iPod.

•

Depending on the version of the operating system of the iPod/iPhone, some functions may

not operate on this unit.

About Android device

•

This unit supports Android OS 4.1 and above.

•

Some Android devices (with OS 4.1 and above) may not fully support Android Open Accessory

(AOA) 2.0.

•

If the Android device supports both mass storage class device and AOA 2.0, this unit always

playback via AOA 2.0 as priority.

Muting upon the reception of a phone call

Connect the MUTE wire to your telephone using a commercial telephone accessory. ( 15)

When a call comes in, “CALL” appears.

•

To continue listening to the audio system during a call, press . “CALL” disappears

and the audio system resumes.

When the call ends, “CALL” disappears.

(The audio system pauses.)

(The audio system resumes.)

Change the display information

Each time you press

•

If the information is unavailable or not recorded,

(eg. station name, playing time) appears.

Source name Display information

STANDBY

TUNER

USB

IPOD or ANDROID

AUX

Turn off the display information.

DISP

, the display information changes.

Source name (*) Clock (back to the beginning)

Frequency (*) Clock (back to the beginning)

(For FM Radio Data System stations only)

Station name (*) Radio text Radio text+ Title/Artist Frequency

(For MP3/WMA/WAV/FLAC files)

Track title/Artist (*) Album title/Artist Folder name File name

Track title/Artist (*) Album title/Artist Playing time Clock (back to the beginning)

Source name (*) Clock (back to the beginning)

Clock (back to the beginning)

Playing time Clock (back to the beginning)

“NO TEXT”, “NO INFO”, or other information

ENGLISH

Warning

•

The unit can only be used with a 12V DC power supply, negative

ground.

•

Disconnect the battery’s negative terminal before wiring and

mounting.

•

Do not connect Battery wire (yellow) and Ignition wire (red) to the

car chassis or Ground wire (black) to prevent a short circuit.

•

Insulate unconnected wires with vinyl tape to prevent a short circuit.

•

Be sure to ground this unit to the car’s chassis again after

installation.

Caution

•

For safety’s sake, leave wiring and mounting to professionals.

Consult the car audio dealer.

•

Install this unit in the console of your vehicle. Do not touch the

metal parts of this unit during and shortly after use of the unit. Metal parts such as the heat sink and enclosure become hot.

•

Do not connect the [ wires of speakers to the car chassis or Ground

wire (black), or connect them in parallel.

•

Mount the unit at an angle of less than 30º.

•

If your vehicle wiring harness does not have the ignition terminal,

connect Ignition wire (red) to the terminal on the vehicle’s fuse box

INSTALLATION / CONNECTION

which provides 12 V DC power supply and is turned on and off by the ignition key.

•

Keep all cables away from heat dissipate metal parts.

•

After the unit is installed, check whether the brake lamps, blinkers,

wipers, etc. on the car are working properly.

•

If the fuse blows, first make sure the wires are not touching car’s

chassis, then replace the old fuse with one that has the same rating.

Basic procedure 1

Remove the key from the ignition switch, then disconnect the [ terminal of the car battery.

2 Connect the wires properly.

See Wiring connection. (

15)

3 Install the unit to your car.

See Installing the unit (in-dash mounting).

4 Connect the [ terminal of the car battery. 5 Reset the unit. ( 

)

Installing the unit (in-dash mounting)

Hook on the top side

Orientate the trim plate as illustrated before fitting.

Bend the appropriate tabs to hold the mounting sleeve firmly in place.

When installing without the mounting sleeve 1

Remove the mounting sleeve and trim plate from the unit.

2 Align the holes in the unit (on both sides) with the

vehicle mounting bracket and secure the unit with screws (supplied).

Use only the specified screws. Using wrong screws might damage the unit.

How to remove the unit 1

Detach the faceplate.

2 Fit the catch pin on the extraction keys into

the holes on both sides of the trim plate, then pull it out.

3 Insert the extraction keys deeply into the slots

on each side, then follow the arrows as shown on the right.

Do the required wiring. (

15)

Dashboard of your car

Wiring connection

IMPORTANT :

professionals for your safety. Consult your car audio dealer.

When connecting to an external amplifier, connect its ground wire to the car’s chassis to avoid damaging the unit.

To front speaker (left)

To front speaker (right)

To rear speaker (right)

Battery

We recommend installing the unit with a commercially available custom wiring harness specific for your car and leave this job to

Fuse (10A)

White

White/Black

Gray

Gray/Black

Green

To rear speaker (left)

Ignition switch

Car fuse box

Black (Ground wire)

To the metallic body or chassis of the car

Green/Black

Purple

Purple/Black

Red (Ignition wire)

Yellow (Battery wire)

Rear/ subwoofer output

Antenna terminal

If no connections are made, do not let the wire come out from the tab.

Brown (Mute control wire)

Blue/White (Power control wire/

Antenna control wire)

Light blue/yellow (Steering remote

control wire)

To the terminal that is grounded when the telephone rings or during conversation

( 15)

(To connect the Kenwood navigation system, refer your navigation manual.)

To the power control terminal when using the optional power amplifier or to the antenna control terminal in the vehicle

To the steering wheel remote control adapter

Part list for installation

(A)

Faceplate

(B)

Trim plate

(C)

Mounting sleeve

(D)

Wiring harness

(E)

Extraction key

(F)

Screws

ENGLISH

SPECIFICATIONS

FM Frequency Range 87.5 MHz — 108.0 MHz (50 kHz space)

Usable Sensitivity (S/N=26dB) 8.2dBf (0.71μV/75Ω)

Quieting Sensitivity (DINS/N=46dB)

Frequency Response (±3dB) 30 Hz — 15 kHz

Tuner

Signal-to-Noise Ratio (MONO) 64 dB

Stereo Separation (1kHz) 40dB

AM Frequency Range 530kHz — 1700kHz (10kHz space)

Usable Sensitivity (S/N=20dB) 29dBμ (28.2μV)

USB Standard USB1.1, USB2.0 Full Speed

File System FAT12/16/32

Maximum Supply Current DC5V

Frequency Response (±1dB) 20Hz — 20kHz

Signal-to-Noise Ratio (1kHz) 105 dB

Dynamic Range 88dB

USB

Channel Separation 90dB

MP3 Decode Compliant with MPEG-1/2 Audio Layer-3

WMA Decode Compliant with Windows Media Audio

WAV Decode Linear-PCM

FLAC Decode FLAC file (Up to 48kHz / 16bit)

17.2dBf (2.0μV/75Ω)

1A

Maximum Output Power 50W×4

Full Bandwidth Power 22W×4 (at less than 1% THD)

Speaker Impedance 4Ω—8Ω

Tone Action Bass 100Hz±8dB

Audio

Preout Level/Load (USB) 2500mV/10kΩ

Preout Impedance ≤600Ω



Frequency Response (±3dB) 20Hz—20kHz

Input Maximum Voltage 1000mV

Auxiliary

Input Impedance 30kΩ

Operating Voltage 14.4V (10.5V—16V allowable)

Maximum Current Consumption 10A



Operational Temperature Range –10°C—+60°C

Installation Size (W×H×D) 182mm×53mm×107mm

General

Weight 0.6kg (1.35lbs)

Subject to change without notice.

Middle 1.0kHz±8dB

Treble 12.5kHz±8dB

(7-3/16"×2-1/16"×4-3/16")

+ 36 hidden pages