Kenwood KMM-204, KMM-104 Instruction Manual

KMM-204 KMM-104

DIGITAL MEDIA RECEIVER

INSTRUCTION MANUAL

CONTENTS BEFORE USE

BEFORE USE 2

BASICS 3

GETTING STARTED 4

1 Select the display language

and cancel the demonstration 2 Set the clock and date 3 Set the initial settings

RADIO 5

USB/iPod/ANDROID 7

AUX 9

Pandora® 10

AUDIO SETTINGS 11

DISPLAY SETTINGS 12

TROUBLESHOOTING 13

REFERENCES 15

Maintenance More information

INSTALLATION/ CONNECTION 16

SPECIFICATIONS 19

IMPORTANT

•

To ensure proper use, please read through this manual before using this product. It is especially important that you read and observe

Warning and Caution in this manual.

•

Please keep the manual in a safe and accessible place for future reference.

WARNING

•

Do not operate any function that takes your attention away from safe driving.

•

Do not ingest the battery, Chemical Burn Hazard

The remote control supplied with this product contains a coin/button cell battery. If the coin/button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death. Keep new and used batteries away from children. If the battery compartment does not close securely, stop using the product and keep it away from children. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.

Caution

Volume setting:

•

Adjust the volume so that you can hear sounds outside the car to prevent accidents.

•

Lower the volume before playing digital sources to avoid damaging the speakers by the sudden increase of the output level.

General:

•

Avoid using the external device if it might hinder safe driving.

•

Make sure all important data has been backed up. We shall bear no responsibility for any loss of recorded data.

•

Never put or leave any metallic objects (such as coins or metal tools) inside the unit, to prevent a short circuit.

•

Depending on the types of cars, the antenna will automatically extend when you turn on the unit with the antenna control wire connected

( 18)

. Turn off the unit or change the source to STANDBY when parking at a low ceiling area.

Remote control (RC-406):

•

Do not leave the remote control in hot places such as on the dashboard.

•

The Lithium battery is in danger of explosion if replaced incorrectly. Replace it only with the same or equivalent type.

•

The battery pack or batteries shall not be exposed to excessive heat such as sunshine, fire or the like.

How to read this manual

•

Operations are explained mainly using buttons on the faceplate of .

•

English indications are used for the purpose of explanation. You can select the display language from the

•

[XX]

indicates the selected items.

•

( XX)

indicates references are available on the stated page.

[FUNCTION]

menu.

( 5)

ENGLISH

BASICS

Faceplate

Remote control (RC-406)

Volume knob

Detach button

How to resetAttach Detach

To On the faceplate On the remote control

Turn on the power

Adjust the volume Turn the volume knob.

Select a source

Change the display information Press DISP repeatedly.

Press

• Press and hold to turn off the power.

Press

Display window

Your preset adjustments will be erased except stored radio stations.

repeatedly.

( 16)

Not used

How to replace the battery

Press and hold SRC to turn off the power. ( Pressing SRC does not turn on the power. )

Press

• Press and hold the volume to 15.

Press ATT during playback to attenuate the sound.

• Press again to cancel.

Press SRC repeatedly.

( Not available )

or .

Remote sensor (Do not expose to bright sunlight.)

Pull out the insulation sheet when using for the first time.

to continuously increase

ENGLISH

GETTING STARTED

Select the display language and cancel the demonstration

When you turn on the power (or after you reset the unit), the display shows: “SEL LANGUAGE”

1 Turn the volume knob to select

then press the knob.

[ENG]

is selected for the initial setup.

Then, the display shows: “CANCEL DEMO”

KNOB”.

2 Press the volume knob.

[YES]

is selected for the initial setup.

3 Press the volume knob again.

“DEMO OFF” appears.

Set the clock and date

Press the volume knob to enter

2 Turn the volume knob to select

To adjust the clock

3 Turn the volume knob to select 4 Turn the volume knob to make the settings, then press the knob.

Hour

Minute

5 Turn the volume knob to select 6 Turn the volume knob to select

“PRESS” “VOLUME KNOB”

[ENG]

(English) or

“PRESS” “VOLUME

[FUNCTION] [CLOCK]

[CLOCK ADJUST]

[CLOCK FORMAT] [12H]

, then press the knob.

[24H]

, then press the knob.

[TUR]

(Turkish),

To set the date

7 Turn the volume knob to select 8 Turn the volume knob to select

the knob.

9 Turn the volume knob to select

[DATE FORMAT] [DD/MM/YY]

[DATE SET]

, then press the knob.

[MM/DD/YY]

, then press

10 Turn the volume knob to make the settings, then press the knob.

Day

Month Year or Month Day Year

11 Press and hold to exit.

To return to the previous setting item, press

Set the initial settings

Press repeatedly to enter STANDBY.

2 Press the volume knob to enter

• Pressing AUD enters

[AUDIO CONTROL]

[FUNCTION]

directly.

3 Turn the volume knob to select an item (see the following table),

then press the knob.

4 Repeat step 3 until the desired item is selected or activated. 5 Press and hold to exit.

To return to the previous setting item, press

AUDIO CONTROL

SWITCH PREOUT

SP SELECT

REAR/SUB-W

connected to the line out terminals on the rear (through an external amplifier).

OFF/5/4/6 × 9/6/OEM

or 4inches, 6×9inches or 6inches) or OEM speakers for optimum performance.

: Selects whether rear speakers or a subwoofer are

( 18)

: Selects according to the speaker size (5inches

Default:

ENGLISH

GETTING STARTED RADIO

TUNER SETTING

PRESET TYPE

SYSTEM

KEY BEEP

TDF ALARM

SOURCE SELECT

PANDORA SRC

BUILT-IN AUX

F/W UPDATE

UPDATE SYSTEM

F/W UP xxxx

CLOCK

CLOCK DISPLAY

ENGLISH

TURKCE

NORMAL

:Memorizes one station for each preset button in each band (FM1/FM2/FM3/AM/SW1/SW2).; preset button, regardless of the selected band.

:Activates the keypress tone.;

ON: Activates the alarm if you forget to detach the faceplate when ACC is set to OFF. ; OFF: Deactivates.

(For )

:Enables PANDORA in source selection.;

:Enables AUX in source selection.;

YES

:Starts upgrading the firmware.; NO:Cancels (upgrading is not activated). For details on how to update the firmware, visit <www.kenwood.com/cs/ce/>.

:The clock time is shown on the display even when the unit is turned

off.;

OFF

:Cancels.

Select the display language for if applicable. By default,

[ENGLISH]

is selected.

MIX

:Memorizes one station for each

OFF

:Deactivates.

OFF

:Disables.

OFF

:Disables.

[FUNCTION]

menu and music information

( 10)

( 9)

Search for a station

Press repeatedly to select RADIO.

2 Press repeatedly (or press / on the remote

control) to select FM1/FM2/FM3/AM/SW1/SW2.

3 Press S/T (or press S/ on the remote control) to

search for a station.

• To change the searching method for S/T: Press

repeatedly. AUTO1 : Automatically search for a station. AUTO2 : Search for a preset station. MANUAL : Manually search for a station.

• To store a station: Press and hold one of the number buttons (1to6).

• To select a stored station: Press one of the number buttons (1to6) (or

press one of the number buttons (1to6) on the remote control).

Direct Access Tuning

1 Press DIRECT to enter Direct Access Tuning. 2 Press the number buttons to enter a frequency. 3 Press to search for a station.

• To cancel, press

• If no operation is done for 10seconds after step

is automatically canceled.

(using the remote control)

or DIRECT.

2, Direct Access Tuning

ENGLISH

RADIO

Other settings

Press the volume knob to enter

[FUNCTION]

2 Turn the volume knob to select an item (see the following table),

then press the knob.

3 Repeat step 2 until the desired item is selected or activated. 4 Press and hold to exit.

[PRESET TYPE]. ( 5)

OFF

:Cancels.

Default:

To return to the previous setting item, press

TUNER SETTING

LOCAL SEEK

AUTO MEMORY

MONO SET

NEWS SET ON

REGIONAL ON

AF SET ON

TI ON

: Searches only AM/SW1/SW2 stations with good reception. ;

OFF

:Cancels.

•

Settings made are applicable only to the selected source/station. Once

you change the source/station, you need to make the settings again.

YES

:Automatically starts memorizing 6 stations with good reception.;

:Cancels.

•

Selectable only if

:Improves the FM reception, but the stereo effect may be lost.;

OFF

:Cancels.

: The unit will temporarily switch to News Programme if available. ;

OFF

:Cancels.

: Switches to another station only in the specific region using the “AF”

control.;

: Automatically searches for another station broadcasting the same program in the same Radio Data System network with better reception when the current reception is poor.;

:Allows the unit to temporarily switch to Traffic Information if available (“TI” lights up).;

OFF

:Cancels.

OFF

[NORMAL]

:Cancels.

is selected for

PTY SEARCH1 Turn the volume knob to select the available Program Type, then press

CLOCK

TIME SYNC

Available Program Type for

SPEECH

MUSIC

The unit will search for the Program Type categorized under

[MUSIC]

[MONO SET]/[NEWS SET]/[REGIONAL]/[AF SET]/[TI]/[PTY SEARCH]

• only when the band is FM1/FM2/FM3.

• If the volume is adjusted during reception of traffic information, alarm or news bulletin, the adjusted volume is memorized automatically. It will be applied the next time traffic information, alarm or news bulletin is turned on.

the knob.

Turn the volume knob to select the PTY language (

GERMAN

ON OFF

NEWS, AFFAIRS, INFO CULTURE, SCIENCE, VARIED, WEATHER, FINANCE, CHILDREN, SOCIAL RELIGION, PHONE IN, TRAVEL, LEISURE, DOCUMENT POP M CLASSICS, OTHER M OLDIES, FOLK M

if selected.

), then press the knob.

Press S/T to start searching.

:Synchronizes the unit’s time to the Radio Data System station time.;

:Cancels.

[PTY SEARCH]

(music),

(information),

ROCK M

(music),

(music)

(music),

SPORT, EDUCATE, DRAMA

EASY M

JAZZ, COUNTRY, NATION M

(music),

ENGLISH/FRENCH

LIGHT M

is selectable

(music),

[SPEECH]

ENGLISH

USB/iPod/ANDROID

Start playback

The source changes automatically and playback starts.

USB input terminal

USB

CA-U1EX (max.: 500mA) (optional accessory)

iPod/iPhone

KCA-iP102/KCA-iP103 (optional accessory) or accessory of the iPod/

iPhone

ANDROID

USB cable (commercially available)

KCA-iP102 : 30-pin type, KCA-iP103 : Lightning type

Do not leave the cable inside the car when not using.

Selectable source:

: USB/iPod/ANDROID : USB/ANDROID

To On the faceplate On the remote control

Playback/pause Press .

Reverse/Fast-forward

Select a file

Select a folder

Repeat play

Press and hold S/T. Press and hold S/ .

Press S/T. Press S/

Press / .

Press repeatedly.

FILE REPEAT/FOLDER REPEAT/ALL REPEAT FILE REPEAT/FOLDER REPEAT/REPEAT OFF

Random play

Press repeatedly.

FOLDER RANDOM/RANDOM OFF

: MP3/WMA/WAV/FLAC file, iPod or

Press

/ .

: MP3/WMA/WAV/FLAC file : iPod or ANDROID

ANDROID

Press and hold

When connecting an Android device, “Press [VIEW] to install KENWOOD MUSIC PLAY APP” is shown. Follow the instructions

to select

ALL RANDOM

to install the application. You can also install the latest version of KENWOOD MUSIC PLAY application on your Android device before connecting. For more information, visit <www.kenwood.com/cs/ce/>.

For ANDROID: Applicable only when

This does not work for iPod/ANDROID.

For iPod/ANDROID: Applicable only when

[BROWSE MODE]

is selected.

[MODE OFF]/[BROWSE MODE]

( 8)

is selected.

( 8)

ENGLISH

USB/iPod/ANDROID

Select control mode

While in iPod source, press 5 repeatedly.

MODE ON

: Control iPod using the iPod itself

MODE OFF

While in ANDROID source, press 5 repeatedly.

BROWSE MODE

HAND MODE

pause, file skip, fast-forward or reverse from this unit.

: Control iPod from this unit.

: Control Android device from this unit via KENWOOD

MUSIC PLAY application installed in the Android device.

: Control Android device using the Android device itself via

other media player applications installed in the Android device. However, you can still play/pause and file skip from this unit.

. However,

you can still play/

Select music drive

While in USB source, press 5 repeatedly.

Stored songs in the following drive will be played back.

• Selected internal or external memory of a smartphone (Mass Storage Class).

• Selected drive of a multiple drives device.

Select a file from a folder/list

For iPod/ANDROID, applicable only when selected.

[MODE OFF]/[BROWSE MODE]

1 Press . 2 Turn the volume knob to select a folder/list, then press the knob. 3 Turn the volume knob to select a file, then press the knob.

Quick Search

If you have many files, you can search through them quickly.

Turn the volume knob quickly to browse through the list quickly.

Skip Search

Press S/T to search at a preset skip search ratio.

( 9, [SKIP SEARCH])

• Pressing and holding S/T searches at a 10% ratio.

Alphabet search

You can search for a file according to the first character.

For iPod source

(applicable only for USB and ANDROID source)

(applicable only for iPod and ANDROID source)

1 Turn the volume knob quickly to enter character search. 2 Turn the volume knob to select the character.

• Select “ 3 Press S/T to move to the entry position.

” to search for a character other than AtoZ, 0to9.

• You can enter up to 3characters. 4 Press the volume knob to start searching.

For ANDROID source

1 Press / to enter character search. 2 Turn the volume knob to select the character.

^A^: Upper case letters (A to Z) _A_: Lower case letters (a to z)

-0-: Numbers (0 to 9) : Character other than AtoZ, 0to9

***

3 Press the volume knob to start searching.

• To return to the root folder/first file/top menu, press 5.

• To return to the previous setting item, press

• To cancel, press and hold

ENGLISH

USB/iPod/ANDROID

Direct Music Search

1 Press DIRECT. 2 Press the number buttons to enter a file number. 3 Press to search for music.

• To cancel, press

• Not available if Random Play is selected.

• Not applicable for iPod and ANDROID source.

Listen to TuneIn Radio/TuneIn Radio Pro/Aupeo

(for )

While listening to TuneIn Radio, TuneIn Radio Pro or Aupeo, connect the iPod/iPhone to the USB input terminal of the unit.

• The unit will output the sound from these applications.

Other settings

Press the volume knob to enter

2 Turn the volume knob to select an item (see the following table),

then press the knob.

3 Repeat step 2 until the desired item is selected or activated. 4 Press and hold to exit.

To return to the previous setting item, press

USB

MUSIC DRIVE DRIVE CHANGE

SKIP SEARCH 0.5%/1%/5%/10%

(using the remote control)

or DIRECT.

[FUNCTION]

automatically and playback starts. Repeat steps

the skip search ratio over the total files.

:The next drive (

to 3 to select the following drives.

[DRIVE 1]

: While listening to iPod or ANDROID source, selects

Default:

[DRIVE 5]

) is selected

AUX

Preparation:

Select

[ON]

for

[BUILT-IN AUX]

Start listening

Connect a portable audio player (commercially available).

Auxiliary input jack

3.5mm stereo mini plug with “L” shaped connector (commercially available)

2 Press repeatedly to select AUX. 3 Turn on the portable audio player and start playback.

Set the AUX name

While listening to a portable audio player connected to the unit...

1 Press the volume knob to enter 2 Turn the volume knob to select 3 Turn the volume knob to select 4 Turn the volume knob to select an item, then press the knob.

AUX

(default)/

5 Press and hold to exit.

To return to the previous setting item, press

DVD/PORTABLE/GAME/VIDEO/TV

[SOURCE SELECT]. ( 5)

Portable audio player

[FUNCTION] [SYSTEM] [AUX NAME SET]

, then press the knob.

ENGLISH

Pandora®

Preparation:

Install the latest version of the Pandora application on your device (iPhone/iPod touch), then create an account and log in to Pandora.

• Select

[ON]

for

[PANDORA SRC]

Start listening

Open the Pandora application on your device.

2 Connect your device to the USB input terminal.

USB input terminal

3 Press repeatedly to select PANDORA.

Broadcast starts automatically.

To On the faceplate On the remote control

Playback/pause Press .

Skip a track

Thumbs up or thumbs

down

KCA-iP102 : 30-pin type, KCA-iP103 : Lightning type

Do not leave the cable inside the car when not using.

If thumbs down is selected, the current track is skipped.

[SOURCE SELECT]. ( 5)

KCA-iP102/KCA-iP103 (optional accessory) or accessory of the iPod/iPhone

Press T.

Press / .

Press

/ .

Create and save a new station

Press .

2 Turn the volume knob to select 3 Turn the volume knob to select

press the knob.

A new station is created based on the artist or current song.

[NEW STATION] [FROM ARTIST]

, then press the knob.

[FROM TRACK]

, then

4 Press and hold one of the number buttons (1to5) to store.

To select a stored station: Press one of the number buttons (1to5).

Search for a registered station

Press .

2 Turn the volume knob to select an item, then press the knob.

[BY DATE]

: According to the registered date

[BY A-Z]

: By alphabetical order

3 Turn the volume knob (or press J / K on the remote control) to

select the desired station.

4 Press the volume knob (or press on the remote control) to

confirm.

To cancel, press and hold .

Bookmark current song information

Press and hold the volume knob.

“BOOKMARKED” appears and the information is stored to your device.

• The bookmark is available on your Pandora account but not on this unit.

ENGLISH

Pandora® AUDIO SETTINGS

Delete a station

While listening to PANDORA...

1 Press . 2 Turn the volume knob to select 3 Turn the volume knob to select

knob.

Turn the volume knob to select the desired station to delete, then press the knob.

5 Turn the volume knob to select

[STATION DEL] [BY DATE]

[YES]

, then press the knob.

[BY A-Z]

, then press the knob.

, then press the

6 Press and hold to exit.

To return to the previous setting item, press

While listening to any source...

1 Press AUD to enter

[AUDIO CONTROL]

2 Turn the volume knob to select an item (see the following table),

then press the knob.

3 Repeat step 2 until the desired item is selected or activated. 4 Press and hold to exit.

To return to the previous setting item, press

AUDIO CONTROL

SUB-W LEVEL

BASS LEVEL –8

MID LEVEL –8

TRE LEVEL –8

EQ PRO

BASS ADJUST BASS CTR FRQ 60/80/100/200

MID ADJUST MID CTR FRQ 0.5KHZ/1.0KHZ/1.5KHZ/2.5KHZ

TRE ADJUST TRE CTR FRQ 10.0KHZ/12.5KHZ/15.0KHZ/17.5KHZ

–15

+15 (0

to +8 (+2)

to +8 (+1)

(This setting is stored to

BASS LEVEL –8

BASS Q FACTOR 1.00/1.25/1.50/2.00

BASS EXTEND ON

MID LEVEL –8

MID Q FACTOR 0.75/1.00/1.25

TRE LEVEL –8

) Adjusts the subwoofer output level.

[USER]

directly.

Default:

Adjusts the level to memorize for each source. (Before making an adjustment, select the source you want to adjust.)

: Selects the center frequency.

to +8 (+2):Adjusts the level.

:Adjusts the quality factor.

:Turns on the extended bass.;

center frequency.

to +8 (+1):Adjusts the level.

:Adjusts the quality factor.

center frequency.

to +8 (+1):Adjusts the level.

OFF

:Cancels.

:Selects the

ENGLISH

AUDIO SETTINGS

PRESET EQ DRIVE EQ/TOP40/POWERFUL/ROCK/POPS/EASY/JAZZ/NATURAL

BASS BOOST LV1/LV2/LV3

LOUDNESS LV1/LV2

SUBWOOFER SET ON

LPF SUBWOOFER THROUGH

SUB-W PHASE REVERSE

FADER R15

BALANCE L15

VOLUME OFFSET

SOUND RECNSTR

(Sound reconstruction)

•

[SUB-W LEVEL]/[SUBWOOFER SET]/[LPF SUBWOOFER]/[SUB-W PHASE]

selectable only if

•

[SUB-W LEVEL]/[LPF SUBWOOFER]/[SUB-W PHASE] [SUBWOOFER SET]

USER

: Selects a preset equalizer suitable to the music genre. (Select

[USER]

to use the settings made in

[DRIVE EQ]

is a preset equalizer that reduces noise outside the car or

running noise of the tyres.

:Selects your preferred bass boost level.;

:Selects your preferred low and high frequencies boost to

produce a well-balanced sound at a low volume level.;

:Turns on the subwoofer output.;

:All signals are sent to the subwoofer.;

85HZ/120HZ/160HZ

85Hz/120Hz/160Hz are sent to the subwoofer.

output to be in line with the speaker output for optimum performance. (Selectable only if a setting other than

[LPF SUBWOOFER]

F15 (0

R15 (0

For AUX:

–8

volume level of each source. (Before adjustment, select the source you want to adjust.)

:Creates realistic sound by compensating the high-frequency components and restoring the rise-time of the waveform that are lost in audio data compression.;

[SWITCH PREOUT]

is set to

:Audio signals with frequencies lower than

(180°)/

NORMAL

):Adjusts the rear and front speaker output balance.

):Adjusts the left and right speaker output balance.

to +8(0) ; For other sources: –8 to 0:Preset the initial

is set to

[ON]

[EQ PRO]

OFF

:Cancels.

OFF

:Cancels.

OFF

:Cancels.

(0°):Selects the phase of the subwoofer

OFF

:Cancels.

[SUB-W]. ( 4)

is selectable only if

[THROUGH]

is selected for

DISPLAY SETTINGS

Zone identification for brightness settings

Set the dimmer

Press and hold DISP to turn on or off the dimmer.

• If you have set and hold this button.

Other settings

Press the volume knob to enter

2 Turn the volume knob to select an item

knob.

3 Repeat step 2 until the desired item is selected/activated or follow

the instructions stated on the selected item.

4 Press and hold to exit.

To return to the previous setting item, press

[DIMMER TIME] ( 13)

, it will be canceled once you press

[FUNCTION]

( 13)

, then press the

ENGLISH

+ 28 hidden pages

Kenwood KMM-204, KMM-104 Instruction Manual

Specifications and Main Features

Frequently Asked Questions

User Manual