Kenwood KDC-BT268U User Manual [es]

KDC-BT268U

CD-RECEIVER

INSTRUCTION MANUAL

AMPLI-TUNER LECTEUR DE CD

MODE D’EMPLOI

REPRODUCTOR DE DISCOS COMPACTOS RECEPTOR DE FM/AM

MANUAL DE INSTRUCCIONES

For your records

Record the serial number, found on the back of the unit, in the spaces designated on the warranty card, and in the space provided below. Refer to the model and serial numbers whenever you call upon your Kenwood dealer for information or service on the product. Model KDC-BT268U Serial number

US Residents Only

CAUTION

Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. In compliance with Federal Regulations, following are reproductions of labels on, or inside the product relating to laser product safety.

JVC KENWOOD Corporation 2967-3, ISHIKAWA-MACHI, HACHIOJI-SHI, TOKYO, JAPAN

THIS PRODUCT COMPLIES WITH DHHS RULES 21CFR SUBCHAPTER J IN EFFECT AT DATE OF MANUFACTURE.

Location : Top Plate

FCC WARNING

This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made.

FCC NOTE

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment may cause harmful interference to radio communications, if it is not installed and used in accordance with the instructions. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Información acerca de la eliminación de equipos eléctricos y electrónicos al final de la vida útil (aplicable a los países que hayan adoptado sistemas independientes de recogida de residuos)

Los productos con el símbolo de un contenedor con ruedas tachado no podrán ser desechados como residuos domésticos. Los equipos eléctricos y electrónicos al final de la vida útil, deberán ser reciclados en instalaciones que puedan dar el tratamiento adecuado a estos productos y a sus subproductos residuales correspondientes. Póngase en contacto con su administración local para obtener información sobre el punto de recogida más cercano. Un tratamiento correcto del reciclaje y la eliminación de residuos ayuda a conservar los recursos y evita al mismo tiempo efectos perjudiciales en la salud y el medio ambiente.

Informação sobre a eliminação de pilhas

Este produto não deve ser eliminado como lixo doméstico geral. Devolva a pilha usada ao revendedor ou entidade autorizada para que a mesma seja devolvida ao fabricante ou importador. A reciclagem e a eliminação de lixo de maneira apropriada ajudarão a conservar os recursos naturais ao mesmo tempo que prevenirão os efeitos prejudicais à nossa saúde e ao meio ambiente.

CALIFORNIA, USA ONLY

This product contains a CR Coin Cell Lithium Battery which contains Perchlorate Material— special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate

IC (Industry Canada) Notice

This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause

undesired operation of the device.

Note de IC (Industrie Canada)

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes: (1) l’appareil ne doit pas produire de brouillage; (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le

brouillage est susceptible d’en compromettre le fonctionnement.

Contains Bluetooth Module FCC ID: ZWY8811X IC ID: 12033A-8811X

This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.

CAUTION

This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines and RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment has very low levels of RF energy that is deemed to comply without maximum permissive exposure evaluation (MPE). But it is desirable that it should be installed and operated keeping the radiator at least 20 cm or more away from person’s body.

ATTENTION

Cet équipement est conforme aux limites d’exposition aux rayonnements énoncées pour un environnement non contrôlé et respecte les règles les radioélectriques (RF) de la FCC lignes directrices d’exposition et d’exposition aux fréquences radioélectriques (RF) CNR-102 de l’IC. Cet équipement émet une énergie RF très faible qui est considérée comme conforme sans évaluation de l’exposition maximale autorisée (MPE). Cependant, il est souhaitable qu’il devrait être installé et utilisé en gardant une distance de 20 cm ou plus entre le radiateur et le corps humain.

Para cumplimiento de la IFT:

“La operación de este equipo está sujeta a las siguientes dos condiciones: (1) es posible que este equipo o dispositivo no cause interferencia perjudicial y (2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda

causar su operación no deseada”

SOFTWARE LICENSE AGREEMENT

The software embedded in the Product (hereinafter the "Licensed Software") provided by Licensor is copyrighted to or sublicensable by the Licensor, and this Agreement provides for the terms and conditions which Users shall follow in order to use the Licensed Software.

The User shall use the Licensed Software by agreeing with the terms of this Software License Agreement. This Agreement shall be deemed completed at the time the User (hereinafter the "User") initially used the Product in which the "Licensed Software" is embedded.

The Licensed Software may include the software which has been licensed to the Licensor directly or indirectly from any third party. In such case, some third parties require the Users to follow their conditions for use separately from this Software License Agreement. Such software shall not be subject to this Agreement, and the Users are urged to read the "Important Notice concerning the Software" to be provided separately below.

Article 3 Conditions for Grant of License

1. When the User transfers the Product, it may also transfer the license to use the Licensed Software embedded in the Product (including any related materials, updates and upgrades) on condition that no original, copies or related materials continue in the possession of the User, and that the User shall cause the transferee to comply with this Software License Agreement.

2. The User shall not carry out reverse engineering, disassembling, decompiling or any other code analysis works in connection with the Licensed Software.

Article 4 Right pertaining to the Licensed Software

Any and all copyrights and other rights pertaining to the Licensed Software and related documents shall belong to the Licensor or the original holder of the right who granted to the Licensor the license or sublicense for the Licensed Software (hereinafter the "Original Rightholder"), and the User shall not be entitled to any right other than the license granted hereunder, in respect of the Licensed Software and any related documents.

Article 1 General Provision

The Licensor shall grant to the User a non-exclusive and non-transferable (other than the exceptional case referred to in Article 3, Paragraph 1) licensed to use the Licensed Software within the country of the User. (the country where the User bought the Product(hereinafter the "Country")

Article 2 License

1. The license granted under this Agreement shall be the right to use the Licensed Software in the Product.

2. The User shall not duplicate, copy, modify, add, translate or otherwise alter, or lease the Licensed Software and any related documents, whether in whole or in part.

3. The use of the Licensed Software shall be limited to personal purpose, and the Licensed Software shall not be distributed, licensed or sub-licensed whether it is for commercial purpose or not.

4. The User shall use the Licensed Software according to the directions described in the operation manual or help file, and is prohibited to use or duplicate any data in a manner violating the Copyright Law or any other laws and regulations by applying whole or a part of the Licensed Software.

iii

Article 5 Indemnification of Licensor

1. Neither the Licensor nor the Original Rightholder shall be liable for any damage incurred by the User or any third party due to the exercise of the license granted to the User under this Agreement, unless otherwise restricted by law.

2. The Licensor will offer no guarantee for the merchantability, convertibility and consistency with certain objective of the Licensed Software.

Article 6 Liability to Third Party

If any dispute has arisen with any third party due to an infringement upon a copyright, patent or any other intellectual property right that was caused by the User's use of the Licensed Software, the User shall settle such dispute at its own cost and hold the Licensor and the Original Rightholder harmless from any inconvenience it may cause.

Article 7 Confidentiality

The User shall keep the confidentiality of such portion of the Licensed Software, related documents thereof or any other information to be granted under this Agreement, as well as the conditions of this Agreement as has not yet entered the public domain, and shall not disclose or divulge the same to any third party without approval of the Licensor.

Article 8 Termination

In case the User falls under any of the events described in the following items, the Licensor may immediately terminate this Agreement or claim that the User compensates for the damage incurred by the Licensor due to such event: (1) when the User violated any provision of this Agreement; or (2) when a petition has been filed against the User for an attachment, provisional attachment, provisional disposition or any other compulsory execution.

Article 9 Destruction of the Licensed Software

If this Agreement is terminated pursuant to the provision of Article 8, the User shall destroy the Licensed Software, any related documents and copies thereof within two (2) weeks from such date of termination.

Article 10 Protection of Copyright

1. The copyright and all the other intellectual property rights relating to the Licensed Software shall belong to the Licensor and the Original Rightholder, and in no event shall they be under the ownership of the User.

2. The User shall, whenever it uses the Licensed Software, comply with any laws relating to the copyright and other intellectual property rights.

Article 11 Export Restriction

1. It is prohibited to export the Licensed Software and any related documents outside the country of the User (including transmission thereof outside the country of the User via Internet of other communication tools).

2. The User shall understand that the Licensed Software shall be subject to the export restrictions adopted by the country of User and any other countries.

3. The User shall agree that the software will be subject to any and all applicable international and domestic laws (including the export control regulation of the country of User and any other countries, and any restrictions concerning the end-users, the use by end-users and importing countries to be provided by the country of User and any other countries, and any other governmental authorities).

Article 12 Miscellaneous

1. In the event any part of this Agreement is invalidated by operation of law, the residual provisions shall continue in force.

2. Matters not stipulated in this Agreement or any ambiguity or question raised in the construction of this Agreement shall be provided or settled upon good-faith consultation between the Licensor and the User.

3. The Licensor and the User hereby agree that this Agreement is governed by the laws of Japan, and any dispute arising from, and relating to the rights and obligations under, this Agreement shall be submitted to the exclusive jurisdiction of the Tokyo District Court for its first instance.

Important Notice concerning the Software

-jansson

Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the "Software"), to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions:

The above copyright notice and this permission notice shall be included in all copies or substantial portions of the Software.

THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.

CONTENTS

BEFORE USE ............................... 2

BASICS ........................................ 3

GETTING STARTED .................... 4

1 Select the display language

and cancel the demonstration 2 Set the clock and date 3 Set the initial settings

RADIO ......................................... 5

CD/USB/iPod/ANDROID .......... 7

AUX.............................................. 9

Pandora® .................................. 10

iHeartRadio® ............................ 11

BLUETOOTH® ........................... 12

AUDIO SETTINGS .................... 19

DISPLAY SETTINGS ................. 22

TROUBLESHOOTING .............. 23

REFERENCES ............................ 25

Maintenance More information

INSTALLATION/

CONNECTION .......................... 27

SPECIFICATIONS ..................... 30

BEFORE USE

IMPORTANT

•

To ensure proper use, please read through this manual before using this product. It is especially important that you read and observe

Warning and Caution in this manual.

•

Please keep the manual in a safe and accessible place for future reference.

WARNING

• Do not operate any function that takes your attention away from safe driving.

• Do not ingest the battery, Chemical Burn Hazard

The remote control supplied with this product contains a coin/button cell battery. If the coin/button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death. Keep new and used batteries away from children. If the battery compartment does not close securely, stop using the product and keep it away from children. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.

Caution

Volume setting:

•

Adjust the volume so that you can hear sounds outside the car to prevent accidents.

•

Lower the volume before playing digital sources to avoid damaging the speakers by the sudden increase of the output level.

General:

•

Avoid using the external device if it might hinder safe driving.

•

Make sure all important data has been backed up. We shall bear no responsibility for any loss of recorded data.

•

Never put or leave any metallic objects (such as coins or metal tools) inside the unit to prevent a short circuit.

•

If a disc error occurs due to condensation on the laser lens, eject the disc and wait for the moisture to evaporate.

•

USB rating is indicated on the main unit. To view, detach the faceplate.

•

Depending on the types of cars, the antenna will automatically extend when you turn on the unit with the antenna control wire connected

( 29)

. Turn off the unit or change the source to STANDBY when parking at a low ceiling area.

Remote control (RC-406):

•

Do not leave the remote control in hot places such as on the dashboard.

•

The Lithium battery is in danger of explosion if replaced incorrectly. Replace it only with the same or equivalent type.

•

The battery pack or batteries shall not be exposed to excessive heat such as sunshine, fire or the like.

How to read this manual

•

Operations are explained mainly using buttons on the faceplate.

•

English indications are used for the purpose of explanation. You can select the display language from the

• [XX]

indicates the selected items.

• ( XX)

indicates references are available on the stated page.

( 3)

[FUNCTION]

menu.

( 5)

ENGLISH

BASICS

Faceplate

Detach button

Volume knob

Loading slot

Display window

Remote control (RC-406)

This unit can be remotely controlled with an optionally purchased remote control.

Remote sensor (Do not expose to bright sunlight.)

Pull out the insulation sheet when using for the first time.

How to resetAttach Detach

To On the faceplate On the remote control

Turn on the power

Adjust the volume Turn the volume knob. Press

Select a source

Change the display information Press DISP repeatedly.

Press

• Press and hold to turn off the power.

Press

repeatedly.

( 27)

How to replace the battery

Press and hold SRC to turn off the power. ( Pressing SRC does not turn on the power. )

or .

• Press and hold volume to 15.

Press ATT during playback to attenuate the sound.

• Press again to cancel.

Press SRC repeatedly.

( Not available )

to continuously increase the

ENGLISH

GETTING STARTED

Select the display language and cancel the demonstration

When you turn on the power for the first time (or

[YES], 5

), the display shows: “SEL LANGUAGE” “PRESS” “VOLUME

KNOB”

1 Turn the volume knob to select

then press the knob.

[ENG]

is selected for the initial setup.

Then, the display shows: “CANCEL DEMO”

KNOB”.

[ENG]

2 Press the volume knob.

[YES]

is selected for the initial setup.

3 Press the volume knob again.

“DEMO OFF” appears.

Set the clock and date

Press the volume knob to enter

2 Turn the volume knob to select

To adjust the clock

3 Turn the volume knob to select

[FUNCTION] [CLOCK]

[CLOCK ADJUST]

4 Turn the volume knob to make the settings, then press the knob.

Hour

5 Turn the volume knob to select 6 Turn the volume knob to select

Minute

[CLOCK FORMAT] [12H]

[FACTORY RESET]

(English) or

, then press the knob.

[24H]

[SPA]

(Spanish),

“PRESS” “VOLUME

, then press the knob.

is set to

To set the date

7 Turn the volume knob to select 8 Turn the volume knob to select

the knob.

9 Turn the volume knob to select

[DATE FORMAT] [DD/MM/YY]

[DATE SET]

, then press the knob.

[MM/DD/YY]

, then press

10 Turn the volume knob to make the settings, then press the knob.

Day

Month Year or Month Day Year

11 Press and hold to exit.

To return to the previous setting item, press .

Set the initial settings

Press repeatedly to enter STANDBY.

2 Press the volume knob to enter

[FUNCTION]

3 Turn the volume knob to select an item (see the following table),

then press the knob.

4 Repeat step 3 until the desired item is selected or activated. 5 Press and hold to exit.

To return to the previous setting item, press .

Default:

AUDIO CONTROL

SWITCH PREOUT

TUNER SETTING

PRESET TYPE

REAR/SUB-W

connected to the line out terminals on the rear (through an external amplifier).

NORMAL

(FM1/FM2/FM3/AM).; button, regardless of the selected band.

: Selects whether rear speakers or a subwoofer are

( 29)

:Memorizes one station for each preset button in each band

MIX

:Memorizes one station for each preset

ENGLISH

GETTING STARTED RADIO

SYSTEM

KEY BEEP

SOURCE SELECT

PANDORA SRC

IHEART SRC

BUILT-IN AUX

CD READ

F/W UPDATE

UPDATE SYSTEM

F/W UP xxxx

FACTORY RESET YES

CLOCK

CLOCK DISPLAY

ENGLISH

ESPANOL

:Activates the keypress tone.;

:Enables PANDORA in source selection.;

:Enables IHEARTRADIO in source selection.;

:Enables AUX in source selection.;

:Automatically distinguishes between audio file disc and music CD.;

:Forces to play as a music CD. No sound can be heard if an audio file disc

is played.

YES

:Starts upgrading the firmware.; NO:Cancels (upgrading is not activated). For details on how to update the firmware, visit <www.kenwood.com/cs/ce/>.

:Resets the settings to default (except the stored station).;

:Cancels.

:The clock time is shown on the display even when the unit is turned

off.;

OFF

:Cancels.

Select the display language for if applicable. By default,

[ENGLISH]

is selected.

OFF

:Deactivates.

OFF

[FUNCTION]

OFF

:Disables.

( 10)

OFF

:Disables.

( 11)

:Disables.

( 9)

menu and music information

Search for a station

Press repeatedly to select TUNER.

2 Press repeatedly (or press / on the remote

control) to select FM1/FM2/FM3/AM.

3 Press S/T (or press S/ on the remote control) to

search for a station.

• To change the searching method for S/T: Press repeatedly.

AUTO1 : Automatically search for a station. AUTO2 : Search for a preset station. MANUAL : Manually search for a station.

• To store a station: Press and hold one of the number buttons (1to6).

• To select a stored station: Press one of the number buttons (1to6) (or press one of the number buttons (1to6) on the remote control).

Direct Access Tuning

1 Press DIRECT to enter Direct Access Tuning. 2 Press the number buttons to enter a frequency. 3 Press to search for a station.

• To cancel, press or DIRECT.

• If no operation is done for 10seconds after step is automatically canceled.

(using the remote control)

2, Direct Access Tuning

ENGLISH

RADIO

Other settings

Press the volume knob to enter

[FUNCTION]

2 Turn the volume knob to select an item (see the following table),

then press the knob.

3 Repeat step 2 until the desired item is selected/activated or follow

the instructions stated on the selected item.

4 Press and hold to exit.

To return to the previous setting item, press .

Default:

TUNER SETTING

AUTO MEMORY

MONO SET

TI ON

PTY SEARCH

CLOCK

TIME SYNC

YES

:Automatically starts memorizing 6 stations with good reception.;

:Cancels.

•

Selectable only if

:Improves the FM reception, but the stereo effect may be lost.;

OFF

:Cancels.

:Allows the unit to temporarily switch to Traffic Information if available

(“TI” lights up).;

Select the available Program Type, then press S/T to start.

:Synchronizes the unit’s time to the Radio Broadcast Data System station

time.;

OFF

:Cancels.

[NORMAL]

OFF

:Cancels.

is selected for

[PRESET TYPE]. ( 4)

Available Program Type for

SPEECH : NEWS, INFORM

(religious talk), (spanish talk),

MUSIC

ROCK, CLS ROCK

(softrock),

JAZZ, CLASSICL

(soft rhythm and blues), (spanish music),

The unit will search for the Program Type categorized under [

[

MUSIC

] if selected.

•

[MONO SET]/[TI]/[PTY SEARCH]

FM2/FM3.

• If the volume is adjusted during reception of traffic information or news bulletin, the adjusted volume is memorized automatically. It will be applied the next time traffic information or news bulletin is turned on.

TOP 40, COUNTRY, OLDIES, SOFT, NOSTALGA

[PTY SEARCH]

(information),

PERSNLTY

WEATHER

(classic rock),

(classical),

HIP HOP

is selectable only when the band is FM1/

SPORTS, TALK, LANGUAGE, REL TALK

(personality),

ADLT HIT

R & B

(rhythm and blues),

REL MUSC

PUBLIC, COLLEGE, HABL ESP

(adult hits),

(religious music),

SOFT RCK

(nostalgia),

SOFT R&B

MUSC ESP

SPEECH

] or

ENGLISH

CD/USB/iPod/ANDROID

Start playback

The source changes automatically and playback starts.

Eject disc

USB input terminal

USB

CA-U1EX (max.: 500mA) (optional accessory)

iPod/iPhone

KCA-iP102/KCA-iP103 (optional accessory) iPod/iPhone

ANDROID

Micro USB 2.0 cable (commercially available)

KCA-iP102 : 30-pin type, KCA-iP103 : Lightning type

Do not leave the cable inside the car when not using.

Label side

or accessory of the

To On the faceplate On the remote control

Playback/pause Press .

Reverse/Fast-forward

Select a track/file

Select a folder

Repeat play

Press and hold S/T. Press and hold S/ .

Press S/T. Press S/

Press J/K.

Press repeatedly.

TRACK REPEAT/ALL REPEAT FILE REPEAT/FOLDER REPEAT/ALL REPEAT FILE REPEAT/FOLDER REPEAT/REPEAT OFF

Random play

Press repeatedly.

DISC RANDOM/RANDOM OFF FOLDER RANDOM/RANDOM OFF

: Audio CD

Press

/ .

: MP3/WMA/AAC/WAV/FLAC file : iPod or ANDROID

: MP3/WMA/AAC/WAV/FLAC file, iPod or

ANDROID

Press and hold

When connecting an Android device, “Press [VIEW] to install KENWOOD MUSIC PLAY APP” is shown. Follow the instructions

to select

ALL RANDOM

to install the application. You can also install the latest version of KENWOOD MUSIC PLAY application on your Android device before connecting. For more information, visit <www.kenwood.com/cs/ce/>.

For ANDROID: Applicable only when

For CD: Only for MP3/WMA/AAC files. This does not work for iPod/ANDROID.

For iPod/ANDROID: Applicable only when

For CD: Only for MP3/WMA/AAC files.

[BROWSE MODE]

is selected.

[MODE OFF]/[BROWSE MODE]

( 8)

is selected.

( 8)

ENGLISH

CD/USB/iPod/ANDROID

Select control mode

While in iPodUSB source, press 5 repeatedly.

MODE ON

: Control iPod using the iPod itself. However, you can still play/

MODE OFF

While in ANDROID source, press 5 repeatedly.

BROWSE MODE

HAND MODE

While in USB source, press 5 repeatedly.

Stored songs in the following drive will be played back.

• Selected internal or external memory of a smartphone (Mass Storage

• Selected drive of a multiple drives device.

While listening to TuneIn Radio, TuneIn Radio Pro or Aupeo, connect the iPod/iPhone to the USB input terminal of the unit.

• The unit will output the sound from these applications.

For iPod/ANDROID, applicable only when selected.

1 Press . 2 Turn the volume knob to select a folder/list, then press the knob.

pause, file skip, fast-forward or reverse from this unit.

: Control iPod from this unit.

: Control Android device from this unit via KENWOOD

MUSIC PLAY application installed in the Android device.

: Control Android device using the Android device itself via

other media player applications installed in the Android device. However, you can still play/pause and file skip from this unit.

Select music drive

Class).

Listen to TuneIn Radio/TuneIn Radio Pro/Aupeo

Select a file from a folder/list

[MODE OFF]/[BROWSE MODE]

3 Turn the volume knob to select a file, then press the knob.

Quick Search

If you have many files, you can search through them quickly.

Turn the volume knob quickly to browse through the list quickly.

Skip Search

Press S/T to search at a preset skip search ratio.

SEARCH])

• Pressing and holding S/T searches at a 10% ratio.

Alphabet search

You can search for a file according to the first character.

For iPod USB source

(applicable only for CD, USB and ANDROID source)

(applicable only for iPod USB and ANDROID source)

( 9, [SKIP

(applicable only for iPod USB and ANDROID source)

1 Turn the volume knob quickly to enter character search. 2 Turn the volume knob to select the character.

• Select “ 3 Press S/T to move to the entry position.

” to search for a character other than AtoZ, 0to9.

• You can enter up to 3characters. 4 Press the volume knob to start searching.

For ANDROID source

1 Press J/K to enter character search. 2 Turn the volume knob to select the character.

^A^: Upper case letters (A to Z) _A_: Lower case letters (a to z)

-0-: Numbers (0 to 9) : Character other than AtoZ, 0to9

***

3 Press the volume knob to start searching.

• To return to the root folder/first file/top menu, press 5.

BT AUDIO source.)

• To return to the previous setting item, press .

• To cancel, press and hold

(Not applicable for

ENGLISH

CD/USB/iPod/ANDROID

Direct Music Search

1 Press DIRECT. 2 Press the number buttons to enter a track/file number. 3 Press to search for music.

• To cancel, press or DIRECT.

• Not available if Random Play is selected.

• Not applicable for iPodUSB and ANDROID source.

Settings to use KENWOOD Remote application

KENWOOD Remote application is designed to control the KENWOOD car receiver’s operations from the iPhone/iPod (via USB input terminal).

Preparation:

Install the latest version of KENWOOD Remote application on your device before connecting. For more information, visit <www.kenwood.com/cs/ce/>.

You can make the settings in the same way as connection via Bluetooth.

Other settings

Press the volume knob to enter

2 Turn the volume knob to select an item (see the following table), then press the

knob.

3 Repeat step 2 until the desired item is selected or activated. 4 Press and hold to exit.

To return to the previous setting item, press .

USB

MUSIC DRIVE DRIVE CHANGE

SKIP SEARCH 0.5%/1%/5%/10%

(using the remote control)

playback starts. Repeat steps

ratio over the total files.

:The next drive (

to 3 to select the following drives.

( 17)

[FUNCTION]

: While listening to iPodUSB or ANDROID source, selects the skip search

[DRIVE 1]

[DRIVE 4]

Default:

) is selected automatically and

AUX

Preparation:

Select

[ON]

for

[BUILT-IN AUX]

Start listening

Connect a portable audio player (commercially available).

Auxiliary input jack

3.5mm (1/8") stereo mini plug with “L” shaped connector (commercially available)

2 Press repeatedly to select AUX. 3 Turn on the portable audio player and start playback.

Set the AUX name

While listening to a portable audio player connected to the unit...

1 Press the volume knob to enter 2 Turn the volume knob to select

the knob.

3 Turn the volume knob to select

press the knob.

4 Turn the volume knob to select an item, then press

the knob.

AUX

(default)/

DVD/PORTABLE/GAME/VIDEO/TV

5 Press and hold to exit.

To return to the previous setting item, press .

for

[SOURCE SELECT]. ( 5)

[FUNCTION] [SYSTEM]

[AUX NAME SET]

Portable audio player

, then press

, then

ENGLISH

Pandora®

Preparation:

Install the latest version of the Pandora application on your device (iPhone/iPod touch), then create an account and log in to Pandora.

• Select

[ON]

for

[PANDORA SRC]

Start listening

Open the Pandora application on your device.

2 Connect your device to the USB input terminal.

USB input terminal

3 Press repeatedly to select PANDORA.

Broadcast starts automatically.

To On the faceplate

Playback/pause

Skip a track

Thumbs up or thumbs down

KCA-iP102 : 30-pin type, KCA-iP103 : Lightning type

Do not leave the cable inside the car when not using.

If thumbs down is selected, the current track is skipped.

ENGLISH

[SOURCE SELECT]. ( 5)

KCA-iP102/KCA-iP103 (optional

accessory) iPod/iPhone

Press

Press T.

Press J/K.

or accessory of the

. Press

On the remote control

Press

Create and save a new station

Press .

2 Turn the volume knob to select 3 Turn the volume knob to select

A new station is created based on the artist or current song.

[NEW STATION] [FROM ARTIST]

, then press the knob.

[FROM TRACK]

, then press the knob.

4 Press and hold one of the number buttons (1to5) to store.

To select a stored station: Press one of the number buttons (1to5).

Search for a registered station

Press .

2 Turn the volume knob to select an item, then press the knob.

[SORT BY DATE] [SORT BY A-Z]

: According to the registered date

: By alphabetical order

3 Turn the volume knob (or press J / K on the remote control) to select the desired

station.

4 Press the volume knob (or press on the remote control) to confirm.

To cancel, press and hold .

Bookmark current song information

Press and hold the volume knob.

“BOOKMARKED” appears and the information is stored to your device.

• The bookmark is available on your Pandora account but not on this unit.

Delete a station

While listening to PANDORA...

1 Press . 2 Turn the volume knob to select 3 Turn the volume knob to select

[STATION DEL] [SORT BY DATE]

, then press the knob.

[SORT BY A-Z]

, then press the knob.

4 Turn the volume knob to select the desired station to delete, then press the knob. 5 Turn the volume knob to select

[YES]

, then press the knob.

6 Press and hold to exit.

To return to the previous setting item, press .

iHeartRadio®

Preparation:

Install the latest version of iHeartAuto application on your device (iPhone/iPod touch), then create an account and log in to iHeartRadio.

• Select

[ON]

for

[IHEART SRC]

Start listening

Open the iHeartAuto application on your device.

2 Connect your device to the USB input terminal.

USB input terminal

3 Press repeatedly to select IHEARTRADIO.

Broadcast starts automatically.

KCA-iP102 : 30-pin type, KCA-iP103 : Lightning type

Do not leave the cable inside the car when not using.

[SOURCE SELECT]. ( 5)

KCA-iP102/KCA-iP103 (optional

accessory) iPod/iPhone

or accessory of the

To On the faceplate On the remote control

Playback/pause

Skip a track for custom station

Thumbs up or thumbs down

Create a new/custom station

Scan for live station

Press

Press T.

Press J/K.

Press 1.

. Press

Press 2 to start scanning. Press 2 again to listen to the station.

Press

( Not available )

Search and store a station

Press .

2 Turn the volume knob to select a category, then press the knob. 3 Turn the volume knob (or press J / K on the remote control) to select the desired

station.

4 Press the volume knob (or press on the remote control) to confirm.

When a city list appears, you can search cities in alphabetical order by turning the

volume knob quickly.

To cancel, press and hold

To store a station: Press and hold one of the number buttons (3, 4or5). To select a stored station: Press one of the number buttons (3, 4or5).

ENGLISH

BLUETOOTH®

BLUETOOTH — Connection

Supported Bluetooth profiles

– Hands-Free Profile (HFP) – Advanced Audio Distribution Profile (A2DP) – Audio/Video Remote Control Profile (AVRCP) – Serial Port Profile (SPP) – Phonebook Access Profile (PBAP)

Connect the microphone

Rear panel

Microphone (supplied)

Microphone input jack

( 29)

Pair and connect a Bluetooth device for the first time

Press to turn on the unit.

2 Search and select this unit model name (KDC-BT2*) on the Bluetooth device.

“PAIRING”

on the display.

“PASS XXXXXX” Device name “PRESS” “VOLUME KNOB” appears

• For some Bluetooth devices, you may need to enter the Personal Identification

Number (PIN) code immediately after searching.

3 Press the volume knob to start pairing.

“PAIRING OK” appears when pairing is completed.

Supported Bluetooth codecs

– Sub Band Codec (SBC) – Advanced Audio Coding (AAC)

Secure using cord clamps (not supplied) if necessary.

Adjust the microphone angle

Once pairing is completed, Bluetooth connection is established automatically. “BT1” and/or “BT2” on the display window lights up.

• This unit supports Secure Simple Pairing (SSP).

• Up to five devices can be registered (paired) in total.

• Once the pairing is completed, the Bluetooth device will remain registered in the unit even if you reset the unit. To delete the paired device,

• A maximum of two Bluetooth phones and one Bluetooth audio device can be connected at any time.

However, while in BT AUDIO source, you can connect to

five Bluetooth audio devices and switch between these five devices. (

• Some Bluetooth devices may not automatically connect to the unit after pairing. Connect the device to the unit manually.

• Refer to the instruction manual of the Bluetooth device for more information.

)

16, [DEVICE DELETE]

Auto Pairing

When you connect iPhone/iPod touch/Android device to the USB input terminal, pairing request (via Bluetooth) is automatically activated.

Press the volume knob to pair once you have confirmed the device name.

Automatic pairing request is activated only if: – Bluetooth function of the connected device is turned on. –

[AUTO PAIRING]

– KENWOOD MUSIC PLAY application is installed on the

Android device (

is set to

7) and

[ON]. ( 16)

[BROWSE MODE]

is selected

( 8)

ENGLISH

BLUETOOTH®

BLUETOOTH — Mobile phone

Receive a call

When there is an incoming call:

• The unit answers the call automatically if set to a selected time.

During a call:

• If you turn off the unit or detach the faceplate, the Bluetooth connection is disconnected.

The following operations may differ or not available depending on the connected phone.

( 14)

[AUTO ANSWER]

To On the faceplate On the remote control

First incoming call...

Answer a call

Reject a call

End a call

While talking on the first incoming call...

Answer another incoming

call and hold the current call

Reject another incoming call

While having two active calls...

End current call and activate held call

Swap between the current call and held call

Adjust the phone volume

[00]

[35]

(Default:

Switch between hands-free and private talk modes

[15]

Press

or the volume knob or one of the number buttons (1 to 6).

Press

Turn the volume knob during

)

a call.

• This adjustment will not

affect the volume of the other sources.

Press

• Operations may vary

according to the connected Bluetooth device.

. Press .

during a call.

Press

( Not available )

ENGLISH

BLUETOOTH®

Improve the voice quality

While talking on the phone...

1 Press the volume knob to enter

[FUNCTION]

2 Turn the volume knob to select an item (see the following table),

then press the knob.

3 Repeat step 2 until the desired item is selected or activated. 4 Press and hold to exit.

To return to the previous setting item, press .

MIC GAIN –10

NR LEVEL –5

ECHO CANCEL –5

to

+10(–4

number increased.

to+5(0):Adjust the noise reduction level until the least noise is

being heard during a phone conversation.

to+5(0):Adjust the echo cancellation delay time until the least

echo is being heard during a phone conversation.

):The sensitivity of the microphone increases as the

Answer incoming call automatically

Press to enter Bluetooth mode.

1 2 Turn the volume knob to select 3 Turn the volume knob to select

[SETTINGS]

, then press the knob.

[AUTO ANSWER]

, then press the knob.

4 Turn the volume knob to select an item, then press the knob.

to 30 (in seconds)/

OFF

(default)

5 Press and hold to exit.

To return to the previous setting item, press .

Make a call

You can make a call from the call history, phonebook, or dialing the number. Call by voice is also possible if your mobile phone has the feature.

1 Press to enter Bluetooth mode.

“(First device name)” appears.

• If two Bluetooth phones are connected, press again to switch to

another phone.

“(Second device name)” appears. 2 Turn the volume knob to select an item (see the following table),

then press the knob.

3 Repeat step 2 until the desired item is selected/activated or follow

the instructions stated on the selected item.

4 Press and hold to exit.

To return to the previous setting item, press .

CALL HISTORY

(Applicable only if the phone supports PBAP.)

Press the volume knob to select a name or a phone number.

• “I” indicates call received, “O” indicates call made, “M” indicates call missed.

• Press

DISP

• “NO DATA” appears if there is no recorded call history.

Press the volume knob to call.

to change the display category (NUMBER or NAME).

ENGLISH

BLUETOOTH®

PHONE BOOK

NUMBER DIAL

VOICE

BATT LOW

NO SIGNAL/LOW/MID/MAX*:Shows the strength of the current received signal.

Functionality depends on the type of the phone used.

(Applicable only if the phone supports PBAP.)

Turn the volume knob quickly to enter alphabet search mode (if the

phonebook contains many contacts).

The first menu (ABCDEFGHIJK) appears.

• To go to the other menu (LMNOPQRSTUV or WXYZ1

• To select the desired first letter, turn the volume knob or press

S / T

Select “1” to search with numbers and select “

Turn the volume knob to select a name, then press the knob.

Turn the volume knob to select a phone number, then press the knob to call.

•

The phonebook of the connected phone is automatically transferred to the

unit when pairing.

•

Contacts are categorized as: HM (home), OF (office), MO (mobile), OT (other),

GE (general)

•

This unit can display only non-accent letters. (Accent letters such as “Ú” is

showns as “U”.)

Turn the volume knob to select a number (0 to 9) or character ( , #, +).

Press

Repeat steps

Press the volume knob to call.

(or using the remote control)

Press the number buttons (0 to 9) to enter the phone number.

Press to call.

Speak the name of the contact you want to call or the voice command to control the phone functions.

MID/FULL*:Shows the strength of the battery.

, then press the knob.

S / T

to move the entry position.

and 2 until you finish entering the phone number.

( Make a call using voice recognition)

), press

J / K

” to search with symbols.

Make a call using voice recognition

Press and hold to activate the voice recognition of the

connected phone.

2 Speak the name of the contact you want to call or the voice

command to control the phone functions.

• Supported Voice Recognition features vary for each phone. Refer to the instruction manual of the connected phone for details.

• This unit also supports the intelligent personal assistant function of iPhone.

Settings in memory

Store a contact in memory

You can store up to 6 contacts into the number buttons (1 to 6).

1 Press to enter Bluetooth mode. 2 Turn the volume knob to select

[NUMBER DIAL]

, then press the knob.

[CALL HISTORY], [PHONE BOOK]

3 Turn the volume knob to select a contact or enter a phone

number.

If a contact is selected, press the volume knob to show the

phone number.

4 Press and hold one of the number buttons (1 to 6).

“STORED” appears when the contact is stored. To erase a contact from the preset memory, select

step

2 and store a blank number.

[NUMBER DIAL]

Make a call from memory

Press to enter Bluetooth mode.

1 2 Press one of the number buttons (1 to 6). 3 Press the volume knob to call.

“NO MEMORY” appears if there is no contacts stored.

ENGLISH

BLUETOOTH®

Other settings

Press the volume knob to enter

[FUNCTION]

2 Turn the volume knob to select an item (see the following table), then press the

knob.

3 Repeat step 2 until the desired item is selected/activated or follow the

instructions stated on the selected item.

4 Press and hold to exit.

To return to the previous setting item, press .

Default:

BT MODE

PHONE SELECT

AUDIO SELECT

DEVICE DELETE

PIN CODE EDIT (0000)

RECONNECT ON

AUTO PAIRING ON

INITIALIZE YES

Selects the phone or audio device to connect or disconnect. “

” appears in front of the device name when connected.

“

” appears in front of the current playback audio device.

•

You can only connect a maximum of two Bluetooth phones and one Bluetooth audio

device at any time.

Turn the volume knob to select a device to delete, then press the knob.

Turn the volume knob to select

Changes the PIN code (up to 6 digits).

Turn the volume knob to select a number.

Press S/T to move the entry position.

Repeat steps

Press the volume knob to confirm.

:The unit automatically reconnect when the last connected Bluetooth device is within

range.;

:The unit automatically pair supported Bluetooth device (iPhone/iPod touch/Android device) when it is connected through USB input terminal.Depending on the operating system of the connected device, this function may not work. ;

:Initializes all the Bluetooth settings (including stored pairing, phonebook, and

etc.).;

and 2 until you finish entering the PIN code.

OFF

:Cancels.

[YES]

[NO]

, then press the knob.

OFF

:Cancels.

Bluetooth test mode

You can check the connectivity of the supported profile between the Bluetooth device and the unit.

• Make sure there is no Bluetooth device paired.

1 Press and hold .

“PLEASE PAIR YOUR PHONE PIN 0000” appears.

2 Search and select this unit model name (KDC-BT2*) on

the Bluetooth device.

3 Operate the Bluetooth device to confirm pairing.

“TESTING” flashes on the display.

The connectivity result (OK or NG) appears after the test.

PAIRING: Pairing status HF CNT: Hands-Free Profile (HFP) compatibility AUD CNT: Advanced Audio Distribution Profile (A2DP)

PB DL: Phonebook Access profile (PBAP) compatibility

To cancel test mode, press and hold unit.

compatibility

to turn off the

ENGLISH

BLUETOOTH®

BLUETOOTH — Audio

While in BT AUDIO source, you can connect to five Bluetooth audio devices and switch between these five devices.

Audio player via Bluetooth

Press repeatedly (or press SRC on the remote control) to select BTAUDIO.

2 Operate the Bluetooth audio player to start playback.

To On the faceplate On the remote control

Playback/pause

Select group or folder

Reverse/ Forward skip

Reverse/Fastforward

Repeat play Press

Random play Press and hold

Press

Press J / K.

Press S/T. Press S/

Press and hold S/T. Press and hold S/

ALL REPEAT, FILE REPEAT REPEAT OFF

select

• Press

RANDOM OFF

. Press

repeatedly.

ALL RANDOM

to select

Press

( Not available )

/ .

To On the faceplate On the remote control

Select a file from a folder/list

Switch between connected Bluetooth audio device

Pressing the “Play” key on the connected device itself also causes switching of sound output

from the device.

Operations and display indications may differ according to their availability on the connected device.

Refer to “Select a file from a folder/ list” on page 8.

Press 5.*

( Not available )

Settings to use KENWOOD Remote application

KENWOOD Remote application is designed to control the KENWOOD

car receiver’s operations from the iPhone/iPod (via Bluetooth or via USB input terminal) or Android smartphone (via Bluetooth).

Preparation:

Install the latest version of KENWOOD Remote application on your device

before connecting. For more information, visit <www.kenwood.com/cs/ce/>.

1 Press the volume knob to enter 2 Turn the volume knob to select an item

[FUNCTION]

( 18)

, then press the knob.

3 Repeat step 2 until the desired item is selected or activated. 4 Press and hold to exit.

To return to the previous setting item, press .

ENGLISH

BLUETOOTH®

Default:

REMOTE APP

SELECT

IOS YES:Selects iPhone/iPod to use the application via Bluetooth or connected via USB input

ANDROID YES

ANDROID LIST

STATUS

Displayed only when

Listen to iPhone/iPod via Bluetooth

You can listen to the songs on the iPhone/iPod via Bluetooth on this unit.

Press repeatedly to select iPodBT.

• You can operate the iPod/iPhone in the same way as iPod/iPhone via USB input terminal

• If you plug in an iPhone/iPod to the USB input terminal while listening to iPodBT source, the source automatically change to iPodUSB. Press select iPodBT if the device is still connected via Bluetooth.

Select the device (IOS or ANDROID) to use the application.

terminal.;

NO:Cancels. If IOS is selected, select iPod BT source (or iPod USB if your iPhone/iPod is connected via USB input terminal) to activate the application.

•

The connectivity of the application will be interrupted or disconnected if:

– You change from iPod BT source to any playback source connected via the USB

input terminal.

– You change from iPod USB source to iPod BT source.

:Selects Android smartphone to use the application via Bluetooth.;

: Cancels.

*:

Selects the Android smartphone to use from the list.

Shows the status of the selected device. IOS CONNECTED: You are able to use the application using the iPhone/iPod connected via Bluetooth or USB input terminal.

IOS NOT CONNECTED: No IOS device is connected to use the application. ANDROID CONNECTED: You are able to use the application using the Android smartphone

connected via Bluetooth.

ANDROID NOT CONNECTED: No Android device is connected to use the application.

[ANDROID]

[SELECT]

is set to

[YES]

( 7)

Internet radio via Bluetooth

You can listen to internet radio (Pandora and iHeartRadio) on the iPhone/iPod/Android device via Bluetooth on this unit.

• Make sure the USB input terminal is not connected to any device.

Listen to Pandora

Preparation:

Select

[ON]

for

[PANDORA SRC]

[SOURCE SELECT]. ( 5)

1 Open the Pandora application on your device. 2 Connect your device via Bluetooth connection.

( 12)

3 Press repeatedly to select PANDORA (for iPhone/iPod)

or PANDORA BT (for Android device).

The source switches and broadcast starts automatically.

• You can operate Pandora in the same way as Pandora via USB input terminal.

( 10)

Listen to iHeartRadio

Preparation:

Select

[ON]

for

[IHEART SRC]

[SOURCE SELECT]. ( 5)

1 Open the iHeartAuto application on your device. 2 Connect your device via Bluetooth connection.

( 12)

3 Press repeatedly to select IHEARTRADIO.

The source switches and broadcast starts automatically.

• You can operate iHeartRadio in the same way as iHeartRadio via USB input terminal.

( 11)

ENGLISH

AUDIO SETTINGS

While listening to any source...

1 Press the volume knob to enter 2 Turn the volume knob to select an item (see the following table),

then press the knob.

3 Repeat step 2 until the desired item is selected or activated. 4 Press and hold to exit.

(or using the remote control)

1 Press AUD to enter

[AUDIO CONTROL]

2 Press J / K to select an item, then press .

To return to the previous setting item, press

AUDIO CONTROL

SUB-W LEVEL

MANUAL EQ

BAND1 LEVEL

LEVEL

BASS EXTEND ON

BAND2 LEVEL BAND13 LEVEL

Q FACTOR 1.35/1.50/2.00

PRESET EQ NATURAL/ROCK/POPS/EASY/TOP40/JAZZ/POWERFUL/USER

LEVEL –50

The sound elements (frequency level, tone level, Q factor) are preset into each selection (

LEVEL–9

to each source. (Before making an adjustment, select the source you want to adjust.)

:Turns on the extended bass.;

LEVEL–9

to each source. (Before making an adjustment, select the source you want to adjust.)

a preset equalizer suitable to the music genre. (Select settings made in

[FUNCTION]

LEVEL +10 (LEVEL 0

BAND1 LEVEL

LEVEL +9 (LEVEL 0

:Adjust the quality factor.

[MANUAL EQ]

Default:

): Adjusts the subwoofer output level.

BAND13 LEVEL

):Adjusts the level to memorize for

OFF

):Adjusts the level to memorize for

:Cancels.

[USER]

to use the

: Selects

BASS BOOST LV1/LV2/LV3/LV4/LV5

LOUDNESS LV1/LV2

SUBWOOFER SET ON

FADER R15

BALANCE L15

VOLUME OFFSET –15

SOUND EFFECT

SOUND RECNSTR

(Sound reconstruction)

SPACE ENHANCE

SND REALIZER LV1/LV2/LV3

STAGE EQ LOW/MID/HI

DRIVE EQ ON

OFF

produce a well-balanced sound at a low volume level.;

:Turns on the subwoofer output.;

adjustment, select the source you want to adjust.)

(Not applicable for TUNER source and AUX source.)

:Creates realistic sound by compensating the high-frequency components and restoring the rise-time of the waveform that are lost in audio data compression.;

(Not applicable for TUNER source.)

SML/MED/LRG

OFF

speakers.;

: Boosts the frequency to reduce the noise heard from outside the

car or running noise of the tyres.;

:Cancels.

:Selects your preferred low and high frequencies boost to

F15 (0

R15 (0

to +6 (0):Preset the initial volume level of each source. (Before

:Cancels.

OFF

:Selects your preferred bass boost level.;

OFF

:Cancels.

):Adjusts the rear and front speaker output balance.

):Adjusts the left and right speaker output balance.

OFF

:Cancels.

:Virtually enhances the sound space.;

:Virtually makes the sound more realistic.;

:Virtually adjust the sound position heard from the

:Cancels.

OFF

:Cancels.

OFF

:Cancels.

ENGLISH

AUDIO SETTINGS

SPEAKER SIZE

FRONT SIZE 3.5"/4"/4.75"/5"/6.5"/6.75"/7"/4×6/5×7/6×8

REAR 3.5"/4"/4.75"/5"/6.5"/6.75"/7"/4×6/5×7/6×8/6×9/7×10

SUBWOOFER 6.5"/8"/10"/12"/15" OVER

X ' OVER

TWEETER FRQ

FRONT HPF F - HPF FRQ 30HZ/40HZ/50HZ/60HZ/70HZ/80HZ/90HZ/100HZ

The frequency and slope settings are automatically set for the crossover of the selected speaker.

6×9/7×10

: Selects according to the connected

speaker size for optimum performance.

TWEETER SMALL/MIDDLE/LARGE

according to the connected speaker size for optimum performance.;

NONE

size for optimum performance.;

GAIN LEFT

GAIN RIGHT –8

F - HPF SLOPE –6DB/–12DB/–18DB/–24DB: Adjusts the crossover

F - HPF GAIN –8

size range of the connected tweeter for optimum performance.;

:Not connected.

: Selects according to the connected speaker

1KHZ/1.6KHZ/2.5KHZ/4KHZ/5KHZ/6.3KHZ/8KHZ 10KHZ/12.5KHZ: Adjusts the crossover frequency for

the tweeter speaker.

–8

to 0:Adjusts the output volume of the left tweeter.

to 0:Adjusts the output volume of the right

tweeter.

120HZ/150HZ/180HZ/220HZ/250HZ: Adjusts the crossover frequency for the selected speakers (high pass filter).

;

selected speakers.

slope. (Selectable only if a setting other than selected for

[F - HPF FRQ]

to 0:Adjusts the output volume of the selected

speaker.

NONE

THROUGH

:Not connected.

:Selects according to the

: All signals are sent to the

ENGLISH

[THROUGH]

: Selects

REAR HPF R - HPF FRQ

SUBWOOFER LPF

DTA SETTINGS

CAR SETTINGS

•

The following item is selectable only if

– [SUB-W LEVEL], [SUBWOOFER SET]

–

[SUBWOOFER]

–

[SUBWOOFER LPF]

–

[SUBWOOFER]

•

The following item is selectable only if

– [SUB-W LEVEL]

–

[SUBWOOFER]

–

[SUBWOOFER LPF]

–

[SUBWOOFER]

•

The following item is selectable only if a setting other than

[TWEETER], [REAR]

– [TWEETER], [REAR HPF], [SUBWOOFER LPF]

R - HPF SLOPE

R - HPF GAIN

SW LPF FRQ

SW LPF SLOPE –6DB/–12DB/–18DB/–24DB: Adjusts the crossover

SW LPF PHASE REVERSE

SW LPF GAIN –8

For settings,

[SPEAKER SIZE]

[X ‘ OVER]

[DISTANCE]

[SPEAKER SIZE]

[X ‘ OVER]

[DISTANCE]

and

[SUBWOOFER]

(Refer

FRONT HPF

settings above.)

30HZ/40HZ/50HZ/60HZ/70HZ/80HZ/90HZ 100HZ/120HZ/150HZ/180HZ/220HZ/250HZ

the crossover frequency for the subwoofer (low pass filter).;

THROUGH

: All signals are sent to the subwoofer.

slope. (Selectable only if a setting other than [THROUGH] is selected for

[SW LPF FRQ]

(180°)/ subwoofer output to be in line with the speaker output for optimum performance.

to 0:Adjusts the output volume of the subwoofer.

21, Digital Time Alignment settings

[SWITCH PREOUT]

and

[GAIN]

[DTA SETTINGS]

[SUBWOOFER SET]

and

[GAIN]

[DTA SETTINGS]

[SPEAKER SIZE]

NORMAL

(0°): Selects the phase of the

is set to

[NONE]

[X ‘ OVER]

[SUB-W] ( 4)

[ON] ( 19)

is selected for

: Adjusts

AUDIO SETTINGS

Digital Time Alignment settings

Digital Time Alignment sets the delay time of the speaker output to create a more suitable environment for your vehicle.

• For more information,

[DTA SETTINGS]

DTA SETTINGS

POSITION

DISTANCE 0FT

GAIN –8DB

DTA RESET YES

CAR SETTINGS

CAR TYPE COMPACT/FULL SIZE CAR/WAGON/MINIVAN/SUV

R-SP LOCATION

Determining the value for [DISTANCE] and [GAIN] of

Selects your listening position (reference point).

ALL

:Not compensating;

FRONT LEFT

20.01FT

making an adjustment, select the speaker you want to adjust.)

0DB

(Before making an adjustment, select the speaker you want to adjust.)

:Resets the settings (

[POSITION]

to default.; NO:Cancels.

Identify your car type and rear speaker location in order to make the adjustment for

MINIVAN(LONG)

compensating.

Selects the location of the rear speakers in your vehicle to calculate the furthest distance from the listening position selected (reference point).

• DOOR/REAR DECK

[OFF], [COMPACT], [FULL SIZE CAR], [WAGON]

• 2ND ROW/3RD ROW

[MINIVAN]

FRONT RIGHT:

:Front left seat;

:Fine adjust the distance to compensate. (Before

:Fine adjust the output volume of the selected speaker.

[DISTANCE]

[DTA SETTINGS]

:Selects the type of vehicle.;

:Selectable only when

[MINIVAN(LONG)]

FRONT ALL

Front right seat;

:Front seat

and

[GAIN]

OFF:

[CAR TYPE]

) of the selected

Not

is selected as

[SUV]

is selected

•

Before making an adjustment for

speaker you want to adjust:

FRONT LEFT/FRONT RIGHT/REAR LEFT/REAR RIGHT/SUBWOOFER:

You can only select

[NONE]

• [R-SP LOCATION]

selected for

Determining the value for [DISTANCE] and [GAIN] of [DTA SETTINGS]

[REAR LEFT], [REAR RIGHT]

is selected for

[REAR]

and

[CAR SETTING]

[SPEAKER SIZE]

[DISTANCE]

and

[GAIN]

[DTA SETTINGS]

and

[SUBWOOFER]

is selectable only if a setting other than

[SUBWOOFER]

[SPEAKER SIZE]

If you specify the distance from the center of the currently set listening position to every speaker, the delay time will be automatically computed and set.

Determine the center of the currently set

listening position as the reference point.

Measure the distances from the reference

point to the speakers.

Calculate the differences between the

distance of the furthest speaker (rear

speaker) and other speakers.

Set the

[DISTANCE]

individual speakers.

Adjust

[GAIN]

Example: When listening position

calculated in step 3 for

for individual speakers.

[FRONT ALL]

, select the

if a setting other than

[NONE]

is selected as the

ENGLISH

DISPLAY SETTINGS

Set the dimmer

Press and hold DISP (DIMMER) to turn on or off the dimmer.

• If you have set hold this button.

Other settings

Press the volume knob to enter [

2 Turn the volume knob to select an item (see the following table),

then press the knob.

3 Repeat step 2 until the desired item is selected/activated or follow

the instructions stated on the selected item.

4 Press and hold to exit.

To return to the previous setting item, press .

[DIMMER TIME]

, it will be canceled once you press and

FUNCTION

DISPLAY

DIMMER

BRIGHTNESS1 Select a zone. (See the illustration on the left column.)

TEXT SCROLL AUTO/ONCE

Dim the illumination.

:Dimmer is turned on.;

DIMMER TIME

Turn the volume knob to adjust the

(Default:

[ON]: 6:00PM; [OFF]: 6:00 AM

2 0

to 31: Select your preferred brightness level for the selected zone.

or scroll only once.;

:Select whether to scroll the display information automatically,

OFF

:Cancels.

[ON] [OFF]

)

:Cancels.

:Set the dimmer on and off time.

time, then press the knob.

Default:

ENGLISH

TROUBLESHOOTING

Symptom Remedy

Sound cannot be heard.

“MISWIRING CHECK WIRING THEN PWR ON” appears.

“PROTECTING SEND SERVICE” appears.

General

•

Sound cannot be heard.

•

The unit does not turn on.

•

Information shown on the

display is incorrect.

The unit does not work at all. Reset the unit.

•

Radio reception is poor.

•

Static noise while listening

Radio

to the radio.

Disc cannot be ejected.

Noise is generated. Skip to another track or change the disc.

Tracks do not play back as you intended them to play.

“READING” keeps flashing. Do not use too many hierarchical levels or folders.

CD/USB /iPod

Elapsed playing time is not correct.

“LOADING” appears when you enter search mode by pressing

•

Adjust the volume to the optimum level.

•

Check the cords and connections.

Turn the power off, then check to be sure the terminals of the speaker wires are insulated properly. Turn the power on again.

Send the unit to the nearest service center.

Clean the connectors.

Connect the antenna firmly.

Press and hold careful not to drop the disc when it is ejected. If this does not solve the problem, reset the unit.

Playback order is determined when files are recorded.

This is caused by how the tracks are recorded.

This unit is still preparing the iPod/iPhone music list. It may take some time to load, try again later.

( 25)

( 3)

to forcibly eject the disc. Be

( 3)

Symptom Remedy

Correct characters are not displayed (e.g. album name).

“NA FILE” Make sure the disc contains supported audio files.

“NO DISC” Insert a playable disc into the loading slot.

“TOC ERROR” Make sure the disc is clean and inserted properly.

“PLEASE EJECT” Reset the unit. If this does not solve the problem, consult

“READ ERROR” Copy the files and folders onto the USB device again. If this

“NO DEVICE” Connect a USB device, and change the source to USB again.

CD/USB /iPod

“COPY PRO” A copy-protected file is played. “UNSUPPORTED DEVICE”

appears.

“UNRESPONSIVE DEVICE” appears.

“USB HUB IS NOT SUPPORTED” appears.

“NO MUSIC” Connect a USB device that contains playable audio files.

“iPod ERROR”

•

This unit can only display uppercase letters, numbers, and

a limited number of symbols.

•

Depending on the display language you have selected

( 5)

, some characters may not be displayed correctly.

your nearest service center.

does not solve the problem, reset the USB device or use another USB device.

• Check whether the connected device is compatible with this

unit and ensure the file systems are in supported formats

( 26)

•

Reattach the device.

Make sure the device is not malfunction and reattach the device.

This unit cannot support a USB device connected via a USB hub.

•

Reconnect the iPod.

•

Reset the iPod.

( 26)

ENGLISH

TROUBLESHOOTING

Symptom Remedy

•

Sound cannot

be heard during playback.

•

Sound output only

from the Android device.

Cannot playback at [

BROWSE MODE

ANDROID

“NO DEVICE” or “READING” keeps flashing.

Playback is intermittent or sound skips.

“ANDROID ERROR”/ “NADEVICE”

“ADDERROR” New station creation is unsuccessful.

“CHECKDEVICE” Check the Pandora application on your device.

“NOSKIPS” The skip limit has been reached.

Pandora

“NOSTATIONS” No stations are found.

•

Reconnect the Android device.

•

If in

[HAND MODE]

on the Android device and start playback.

•

If in

[HAND MODE]

application or use another media player application.

•

Restart the Android device.

•

If this does not solve the problem, the connected Android

device is unable to route the audio signal to unit.

•

Make sure KENWOOD MUSIC PLAY APP is installed on the

Android device.

•

Reconnect the Android device and select the appropriate

control mode.

•

If this does not solve the problem, the connected Android

device does not support

•

Switch off the developer options on the Android device.

•

Reconnect the Android device.

•

If this does not solve the problem, the connected Android

device does not support

Turn off the power saving mode on the Android device.

•

Reconnect the Android device.

•

Restart the Android device.

, launch any media player application

, relaunch the current media player

( 7)

[BROWSE MODE]. ( 26)

( 26)

Symptom Remedy

“STATIONLIMIT”

“CONNECT ERROR” Communication is unstable.

“RATING ERROR” Registration of thumbs up/thumbs down has failed due

Pandora

“THUMBS N/A” Registration of thumbs up/thumbs down is not allowed.

“LICENSE ERROR” You try to access from a country which Pandora is not

iHeartRadio station cannot be selected.

iHeartRadio

“NOT CONNECTED” Link to the application is impossible.

No Bluetooth device is detected.

Bluetooth pairing cannot be made.

Echo or noise is heard during a phone

Bluetooth®

conversation.

Phone sound quality is poor.

The number of registered stations has reached its limit. Retry after deleting unnecessary stations from your device.

to insufficient network connectivity.

deliverable.

If “Explicit Content” in [Account Settings] is checked in the web version of iHeartRADIO, custom stations become unavailable.

•

Search from the Bluetooth device again.

•

Reset the unit.

•

Make sure you have entered the same PIN code to both

the unit and Bluetooth device.

•

Delete pairing information from both the unit and the

Bluetooth device, then perform pairing again.

•

Adjust the microphone unit’s position.

•

Check the

•

Reduce the distance between the unit and the

Bluetooth device.

•

Move the car to a place where you can get a better

signal reception.

( 3)

[ECHO CANCEL]

setting.

( 12)

( 14)

ENGLISH

TROUBLESHOOTING

REFERENCES

Symptom Remedy

Voice calling method is not successful.

Sound is being interrupted or skipped during playback of a Bluetooth audio player.

The connected Bluetooth audio player cannot be controlled.

“DEVICE FULL” The number of registered devices has reached its limit.

Bluetooth®

“N/A VOICE TAG” Make sure the same voice as the registered voice tag is

“NOT SUPPORT” The connected phone does not support Voice Recognition

“NO ENTRY”/“NO PAIR” There is no registered device connected/found via

“ERROR” Try the operation again. If “ERROR” appears again, check if

“NO INFO”/“NO DATA” Bluetooth device cannot get the contact information.

“HF ERROR XX”/ “BT ERROR”

•

Use voice calling method in a more quiet environment.

•

Reduce the distance from the microphone when you

speak the name.

•

Make sure the same voice as the registered voice tag is

used.

•

Reduce the distance between the unit and the Bluetooth

audio player.

•

Turn off, then turn on the unit and try to connect again.

•

Other Bluetooth devices might be trying to connect to the

unit.

• Check whether the connected Bluetooth audio player

supports Audio/Video Remote Control Profile (AVRCP). (Refer to the instructions of your audio player.)

•

Disconnect and connect the Bluetooth player again.

Retry after deleting an unnecessary device.

DELETE)

used.

feature or phonebook transfer.

Bluetooth.

the device supports the function you have tried.

Reset the unit and try the operation again. If this does not solve the problem, consult your nearest service center.

( 16, DEVICE

Maintenance

Cleaning the unit

Wipe off dirt on the faceplate with a dry silicone or soft cloth.

Cleaning the connector

Detach the faceplate and clean the connector gently with a cotton swab, being careful not to damage the connector.

Handling discs

•

Do not touch the recording surface of the disc.

•

Do not stick tape etc. on the disc, or use a disc with tape stuck on it.

•

Do not use any accessories for the disc.

•

Clean from the center of the disc and move outward.

•

Clean the disc with a dry silicone or soft cloth. Do not use any solvents.

•

When removing discs from this unit, pull them out horizontally.

•

Remove burrs from the center hole and disc edge before inserting a disc.

More information

For: – Latest firmware updates and latest compatible item list – KENWOOD original application

– Any other latest information

Visit <www.kenwood.com/cs/ce/>.

General

•

This unit can only play the following CDs:

•

For detailed information and notes about the playable audio files, visit

<www.kenwood.com/cs/ce/audiofile/>.

Connector (on the reverse side of the faceplate)

ENGLISH

+ 67 hidden pages