Kenwood KDC-BT610U, KDC-BT10U Instruction Manual

KDC-BT610U KDC-BT510U

CD-RECEIVER

INSTRUCTION MANUAL

CONTENTS

BEFORE USE 2

BASICS 3

GETTING STARTED 4

1 Select the display language

and cancel the demonstration 2 Set the clock and date 3 Set the initial settings

RADIO 6

AUX 7

CD/USB/iPod/ANDROID 8

Pandora® 10

BLUETOOTH® 11

AUDIO SETTINGS 18

DISPLAY SETTINGS 22

TROUBLESHOOTING 23

REFERENCES 25

Maintenance More information

SPECIFICATIONS 28

INSTALLATION/ CONNECTION 29

ENGLISH

BEFORE USE

IMPORTANT

•

To ensure proper use, please read through this manual before using this product. It is especially important that you read and observe

Warning and Caution in this manual.

•

Please keep the manual in a safe and accessible place for future reference.

WARNING

• Do not operate any function that takes your attention away from safe driving.

• Do not ingest the battery, Chemical Burn Hazard

The remote control supplied with this product contains a coin/button cell battery. If the coin/button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death. Keep new and used batteries away from children. If the battery compartment does not close securely, stop using the product and keep it away from children. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.

Caution

Volume setting:

•

Adjust the volume so that you can hear sounds outside the car to prevent accidents.

•

Lower the volume before playing digital sources to avoid damaging the speakers by the sudden increase of the output level.

General:

•

Avoid using the external device if it might hinder safe driving.

•

Make sure all important data has been backed up. We shall bear no responsibility for any loss of recorded data.

•

Never put or leave any metallic objects (such as coins or metal tools) inside the unit to prevent a short circuit.

•

If a disc error occurs due to condensation on the laser lens, eject the disc and wait for the moisture to evaporate.

•

USB rating is indicated on the main unit. To view, detach the faceplate.

•

Depending on the types of cars, the antenna will automatically extend when you turn on the unit with the antenna control wire connected

( 31)

. Turn off the unit or change the source to STANDBY when parking at a low ceiling area.

Remote control (RC-406):

•

Do not leave the remote control in hot places such as on the dashboard.

•

The Lithium battery is in danger of explosion if replaced incorrectly. Replace it only with the same or equivalent type.

•

The battery pack or batteries shall not be exposed to excessive heat such as sunshine, fire or the like.

How to read this manual

•

Operations are explained mainly using buttons on the faceplate of .

•

English indications are used for the purpose of explanation. You can select the display language from the

• [XX]

indicates the selected items.

• ( XX)

indicates references are available on the stated page.

( 3)

[FUNCTION]

menu.

( 5)

BASICS

Faceplate

Volume

knob

slot

Display window

Lights up when Bluetooth connection is established.

( 12)

Remote control (RC-406)

Remote sensor (Do not expose to bright sunlight.)

(supplied for )

Pull out the insulation sheet when using for the first time.

Detach button

enters searching status.

To On the faceplate On the remote control

Turn on the power

Adjust the volume Turn the volume knob. Press

Select a source

Change the display information Press DISP repeatedly.

: Flashes when the unit

How to resetAttach Detach

Press

• Press and hold to turn off the power.

Press

repeatedly.

( 27)

: Remote control functions are not available.

How to replace the battery

Press and hold SRC to turn off the power. ( Pressing SRC does not turn on the power. )

or .

• Press and hold volume to 15.

Press ATT during playback to attenuate the sound.

• Press again to cancel.

Press SRC repeatedly.

( Not available )

to continuously increase the

ENGLISH

GETTING STARTED

Select the display language and cancel the demonstration

When you turn on the power for the first time (or set to

[YES], 5

“VOLUMEKNOB”

1 Turn the volume knob to select

then press the knob.

[ENG]

Then, the display shows: “CANCEL DEMO”

KNOB”.

), the display shows: “SEL LANGUAGE” “PRESS”

[ENG]

is selected for the initial setup.

2 Press the volume knob.

[YES]

is selected for the initial setup.

3 Press the volume knob again.

“DEMO OFF” appears.

Then, the display shows the selected crossover type: “2-WAY X ’ OVER” or “3-WAY X ’ OVER”

• To change the crossover type, see “Change the crossover type”. (

Set the clock and date

Press the volume knob to enter

2 Turn the volume knob to select

[FUNCTION] [CLOCK]

[FACTORY RESET]

(English) or

, then press the knob.

[TUR]

(Turkish),

“PRESS” “VOLUME

5)

To adjust the clock

3 Turn the volume knob to select

[CLOCK ADJUST]

, then press the knob.

4 Turn the volume knob to make the settings, then press the knob.

Hour

5 Turn the volume knob to select 6 Turn the volume knob to select

To set the date

7 Turn the volume knob to select 8 Turn the volume knob to select

9 Turn the volume knob to select

the knob.

Minute

[CLOCK FORMAT] [12H]

[24H]

[DATE FORMAT] [DD/MM/YY]

[DATE SET]

, then press the knob.

[MM/DD/YY]

, then press

10 Turn the volume knob to make the settings, then press the knob.

Day

Month Year or Month Day Year

11 Press and hold to exit.

To return to the previous setting item, press .

Set the initial settings

Press repeatedly to enter STANDBY.

2 Press the volume knob to enter

[FUNCTION]

3 Turn the volume knob to select an item (see the following table),

then press the knob.

4 Repeat step 3 until the desired item is selected or activated. 5 Press and hold to exit.

To return to the previous setting item, press .

Default:

AUDIO CONTROL

SWITCH PREOUT

(For )

REAR/SUB-W

connected to the line out terminals on the rear (through an external amplifier).

: Selects whether rear speakers or a subwoofer are

( 31)

ENGLISH

GETTING STARTED

DISPLAY

EASY MENU

TUNER SETTING

PRESET TYPE

SYSTEM

KEY BEEP

TDF ALARM*ON: Activates the alarm if you forget to detach the faceplate when ACC is set to OFF. ;

SOURCE SELECT

PANDORA SRC

BUILT-IN AUX

CD READ

F/W UPDATE

UPDATE SYSTEM

F/W UP xxxx

FACTORY RESET YES

Not applicable if 3-way crossover is selected.

(For ) When entering

ON OFF

•

ZONE 2 illumination changes to white color when you enter

irregardless of the

•

Refer to the illustration on page 22 for ZONE identification.

NORMAL

FM2/FM3/AM/SW1/SW2).; regardless of the selected band.

OFF: Deactivates.

:Automatically distinguishes between audio file disc and music CD.;

:Forces to play as a music CD. No sound can be heard if an audio file disc is played.

YES

For details on how to update the firmware, visit <www.kenwood.com/cs/ce/>.

[FUNCTION]

:ZONE 1 illumination changes to white color.;

:ZONE 1 illumination remains as

:Memorizes one station for each preset button in each band (FM1/

:Activates the keypress tone.;

:Enables PANDORA in source selection.;

:Enables AUX in source selection.;

:Starts upgrading the firmware.; NO:Cancels (upgrading is not activated).

:Resets the settings to default (except the stored station).; NO:Cancels.

...

[COLOR SELECT]

[EASY MENU]

setting.

MIX

:Memorizes one station for each preset button,

OFF

:Deactivates.

OFF

:Disables.

OFF

:Disables.

( 7)

color.

( 22)

[FUNCTION]

( 10)

CLOCK

CLOCK DISPLAY

ENGLISH

TURKCE

:The clock time is shown on the display even when the

unit is turned off.;

Select the display language for information if applicable. By default,

[ENGLISH]

OFF

is selected.

:Cancels.

[FUNCTION]

menu and music

Change the crossover type

Press repeatedly to enter STANDBY.

1 2 Press and hold number buttons 4 and 5 to enter crossover

select.

The current crossover type appears.

3 Turn the volume knob to select “2WAY” or “3WAY”, then

press the knob.

4 Turn the volume knob to select “YES” or “NO”, then press

the knob.

The selected crossover type appears.

• To cancel, press and hold

• To adjust the selected crossover settings,

( 19, 20)

Caution

Select a crossover type according to how the speakers are connected. ( If you select a wrong type:

• The speakers may damage.

• The output sound level may be extremely high or low.

31)

ENGLISH

RADIO

Search for a station

Press repeatedly to select TUNER.

2 Press repeatedly (or press / on the remote

control) to select FM1/FM2/FM3/AM/SW1/SW2.

3 Press S/T (or press S/ on the remote control) to

search for a station.

• To change the searching method for S/T: Press

repeatedly. AUTO1 : Automatically search for a station. AUTO2 : Search for a preset station. MANUAL : Manually search for a station.

• To store a station: Press and hold one of the number buttons (1to6).

• To select a stored station: Press one of the number buttons (1to6)

(or press one of the number buttons (1to6) on the remote control).

Direct Access Tuning

(using the remote control)

1 Press DIRECT to enter Direct Access Tuning. 2 Press the number buttons to enter a frequency. 3 Press to search for a station.

• To cancel, press or DIRECT.

• If no operation is done for 10seconds after step

is automatically canceled.

2, Direct Access Tuning

Other settings

Press the volume knob to enter

[FUNCTION]

2 Turn the volume knob to select an item (see the following table),

then press the knob.

3 Repeat step 2 until the desired item is selected/activated or follow

the instructions stated on the selected item.

4 Press and hold to exit.

To return to the previous setting item, press .

Default:

TUNER SETTING

LOCAL SEEK

AUTO MEMORY

MONO SET

NEWS SET ON

REGIONAL ON

AF SET ON

TI ON

: Searches only AM/SW1/SW2 stations with good reception. ;

OFF

: Cancels.

•

Settings made are applicable only to the selected source/station. Once

you change the source/station, you need to make the settings again.

YES

:Automatically starts memorizing 6 stations with good reception.;

:Cancels.

•

Selectable only if

:Improves the FM reception, but the stereo effect may be lost.;

OFF

:Cancels.

: The unit will temporarily switch to News Programme if available. ;

OFF

:Cancels.

: Switches to another station only in the specific region using the “AF”

control.;

: Automatically searches for another station broadcasting the same program in the same Radio Data System network with better reception when the current reception is poor.;

:Allows the unit to temporarily switch to Traffic Information if available (“TI” lights up).;

OFF

:Cancels.

OFF

[NORMAL]

:Cancels.

is selected for

OFF

:Cancels.

[PRESET TYPE]. ( 5)

ENGLISH

RADIO

PTY SEARCH1 Turn the volume knob to select the available Program Type, then press

CLOCK

TIME SYNC

the knob.

Turn the volume knob to select the PTY language (

GERMAN

ON OFF

), then press the knob.

Press S/T to start searching.

:Synchronizes the unit’s time to the Radio Data System station time.;

:Cancels.

ENGLISH/FRENCH

AUX

Preparation:

Select

[ON]

for

[BUILT-IN AUX]

Start listening

Connect a portable audio player (commercially available).

Auxiliary input jack

for

[SOURCE SELECT]. ( 5)

Portable audio player

Available Program Type for

SPEECH : NEWS, AFFAIRS, INFO

CULTURE, SCIENCE, VARIED, WEATHER, FINANCE, CHILDREN, SOCIAL RELIGION, PHONE IN, TRAVEL, LEISURE, DOCUMENT

MUSIC

POP M

(music),

CLASSICS, OTHER M OLDIES, FOLK M

The unit will search for the Program Type categorized under

[MUSIC]

if selected.

•

[MONO SET]/[NEWS SET]/[REGIONAL]/[AF SET]/[TI]/[PTY SEARCH]

only when the band is FM1/FM2/FM3.

• If the volume is adjusted during reception of traffic information, alarm or news bulletin, the adjusted volume is memorized automatically. It will be applied the next time traffic information, alarm or news bulletin is turned on.

[PTY SEARCH]

(information),

ROCK M

(music),

(music)

SPORT, EDUCATE, DRAMA

(music),

EASY M

JAZZ, COUNTRY, NATION M

(music),

LIGHT M

(music),

[SPEECH]

is selectable

3.5mm stereo mini plug with “L” shaped connector (commercially available)

2 Press repeatedly to select AUX. 3 Turn on the portable audio player and start playback.

Set the AUX name

While listening to a portable audio player connected to the unit...

1 Press the volume knob to enter 2 Turn the volume knob to select 3 Turn the volume knob to select

[FUNCTION] [SYSTEM] [AUX NAME SET]

, then press the knob.

4 Turn the volume knob to select an item, then press the knob.

AUX

(default)/

DVD/PORTABLE/GAME/VIDEO/TV

5 Press and hold to exit.

To return to the previous setting item, press .

ENGLISH

CD/USB/iPod/ANDROID

Start playback

The source changes automatically and playback starts.

Eject disc

USB input terminal

USB

CA-U1EX (max.: 500mA) (optional accessory)

iPod/iPhone

KCA-iP102/KCA-iP103 (optional accessory) iPod/iPhone

ANDROID

Micro USB 2.0 cable (commercially available)

KCA-iP102 : 30-pin type, KCA-iP103 : Lightning type

Do not leave the cable inside the car when not using.

Label side

or accessory of the

To On the faceplate On the remote control

Playback/pause Press .

Reverse/Fast-forward

Select a track/file

Select a folder

Repeat play

Press and hold S/T. Press and hold S/ .

Press S/T. Press S/

Press J/K.

Press repeatedly.

TRACK REPEAT/ALL REPEAT FILE REPEAT/FOLDER REPEAT/ALL REPEAT FILE REPEAT/FOLDER REPEAT/REPEAT OFF

Random play

Press repeatedly.

DISC RANDOM/RANDOM OFF FOLDER RANDOM/RANDOM OFF

: Audio CD

Press

/ .

: MP3/WMA/AAC/WAV/FLAC file : iPod or ANDROID

: MP3/WMA/AAC/WAV/FLAC file, iPod or

ANDROID

Press and hold

When connecting an Android device, “Press [VIEW] to install KENWOOD MUSIC PLAY APP” is shown. Follow the instructions

to select

ALL RANDOM

to install the application. You can also install the latest version of KENWOOD MUSIC PLAY application on your Android device before connecting. For more information, visit <www.kenwood.com/cs/ce/>.

For ANDROID: Applicable only when

For CD: Only for MP3/WMA/AAC files. This does not work for iPod/ANDROID.

For iPod/ANDROID: Applicable only when

For CD: Only for MP3/WMA/AAC files.

[BROWSE MODE]

is selected.

[MODE OFF]/[BROWSE MODE]

( 9)

is selected.

( 9)

ENGLISH

CD/USB/iPod/ANDROID

Select control mode

While in iPodUSB source, press 5 repeatedly.

MODE ON

: Control iPod using the iPod itself. However, you can still play/

MODE OFF

While in ANDROID source, press 5 repeatedly.

BROWSE MODE

HAND MODE

Select music drive

While in USB source, press 5 repeatedly.

Stored songs in the following drive will be played back.

• Selected internal or external memory of a smartphone (Mass Storage

• Selected drive of a multiple drives device.

Listen to TuneIn Radio/TuneIn Radio Pro/Aupeo

While listening to TuneIn Radio, TuneIn Radio Pro or Aupeo, connect the iPod/iPhone to the USB input terminal of the unit.

• The unit will output the sound from these applications.

Select a file from a folder/list

For iPod/ANDROID, applicable only when selected.

1 Press . 2 Turn the volume knob to select a folder/list, then press the knob.

pause, file skip, fast-forward or reverse from this unit.

: Control iPod from this unit.

: Control Android device from this unit via KENWOOD

MUSIC PLAY application installed in the Android device.

: Control Android device using the Android device itself via

other media player applications installed in the Android device. However, you can still play/pause and file skip from this unit.

Class).

[MODE OFF]/[BROWSE MODE]

3 Turn the volume knob to select a file, then press the knob.

Quick Search

If you have many files, you can search through them quickly.

Turn the volume knob quickly to browse through the list quickly.

Skip Search

Press S/T to search at a preset skip search ratio.

[SKIP SEARCH])

• Pressing and holding S/T searches at a 10% ratio.

Alphabet search

You can search for a file according to the first character.

For iPod USB source

(applicable only for CD, USB and ANDROID source)

(applicable only for iPod USB and ANDROID source)

( 10,

(applicable only for iPod USB and ANDROID source)

1 Turn the volume knob quickly to enter character search. 2 Turn the volume knob to select the character.

• Select “ 3 Press S/T to move to the entry position.

” to search for a character other than AtoZ, 0to9.

• You can enter up to 3characters. 4 Press the volume knob to start searching.

For ANDROID source

1 Press J/K to enter character search. 2 Turn the volume knob to select the character.

^A^: Upper case letters (A to Z) _A_: Lower case letters (a to z)

-0-: Numbers (0 to 9) : Character other than AtoZ, 0to9

***

3 Press the volume knob to start searching.

• To return to the root folder/first file/top menu, press 5.

BT AUDIO source.)

• To return to the previous setting item, press .

• To cancel, press and hold

(Not applicable for

ENGLISH

CD/USB/iPod/ANDROID

Direct Music Search

1 Press DIRECT. 2 Press the number buttons to enter a track/file number. 3 Press to search for music.

• To cancel, press or DIRECT.

• Not available if Random Play is selected.

• Not applicable for iPodUSB and ANDROID source.

Settings to use KENWOOD Remote application

KENWOOD Remote application is designed to control the KENWOOD car receiver’s operations from the iPhone/iPod (via USB input terminal).

Preparation:

Install the latest version of KENWOOD Remote application on your device before connecting. For more information, visit <www.kenwood.com/cs/ce/>.

You can make the settings in the same way as connection via Bluetooth. ( 17)

Other settings

Press the volume knob to enter

2 Turn the volume knob to select an item (see the following table),

then press the knob.

3 Repeat step 2 until the desired item is selected or activated. 4 Press and hold to exit.

To return to the previous setting item, press .

USB

MUSIC DRIVE DRIVE CHANGE

SKIP SEARCH 0.5%/1%/5%/10%

automatically and playback starts. Repeat steps

the skip search ratio over the total files.

(using the remote control)

[FUNCTION]

:The next drive (

to 3 to select the following drives.

: While listening to iPodUSB or ANDROID source, selects

[DRIVE 1]

[DRIVE 4]

Default:

) is selected

Pandora®

Preparation:

Install the latest version of the Pandora application on your device (iPhone/iPod touch), then create an account and log in to Pandora.

• Select

[ON]

for

[PANDORA SRC]

Start listening

Open the Pandora application on your device.

2 Connect your device to the USB input terminal.

USB input terminal

3 Press repeatedly to select PANDORA.

Broadcast starts automatically.

To On the faceplate On the remote control

Playback/pause

Skip a track

Thumbs up or thumbs

down

KCA-iP102 : 30-pin type, KCA-iP103 : Lightning type

Do not leave the cable inside the car when not using.

If thumbs down is selected, the current track is skipped.

[SOURCE SELECT]. ( 5)

KCA-iP102/KCA-iP103 (optional accessory) or accessory of the iPod/iPhone

Press

Press T.

Press J/K.

. Press

Press

ENGLISH

Pandora® BLUETOOTH®

Create and save a new station

Press .

2 Turn the volume knob to select 3 Turn the volume knob to select

A new station is created based on the artist or current song.

[NEW STATION] [FROM ARTIST]

, then press the knob.

[FROM TRACK]

, then press the knob.

4 Press and hold one of the number buttons (1to5) to store.

To select a stored station: Press one of the number buttons (1to5).

Search for a registered station

Press .

2 Turn the volume knob to select an item, then press the knob.

[SORT BY DATE] [SORT BY A-Z]

: According to the registered date

: By alphabetical order

3 Turn the volume knob (or press J / K on the remote control) to select the desired

station.

4 Press the volume knob (or press on the remote control) to confirm.

To cancel, press and hold .

Bookmark current song information

Press and hold the volume knob.

“BOOKMARKED” appears and the information is stored to your device.

• The bookmark is available on your Pandora account but not on this unit.

Delete a station

While listening to PANDORA...

1 Press . 2 Turn the volume knob to select 3 Turn the volume knob to select

[STATION DEL] [SORT BY DATE]

, then press the knob.

[SORT BY A-Z]

, then press the knob.

4 Turn the volume knob to select the desired station to delete, then press the knob. 5 Turn the volume knob to select

[YES]

, then press the knob.

6 Press and hold to exit.

To return to the previous setting item, press .

BLUETOOTH — Connection

Supported Bluetooth profiles

– Hands-Free Profile (HFP) – Advanced Audio Distribution Profile (A2DP) – Audio/Video Remote Control Profile (AVRCP) – Serial Port Profile (SPP) – Phonebook Access Profile (PBAP)

Supported Bluetooth codecs

– Sub Band Codec (SBC) – Advanced Audio Coding (AAC)

Connect the microphone

Rear panel

Microphone input jack

Adjust the microphone angle

Microphone (supplied)

Secure using cord clamps (not supplied) if necessary.

ENGLISH

BLUETOOTH®

Pair and connect a Bluetooth device for the first time

Press to turn on the unit.

2 Search and select this unit model name (KDC-BT6**U/KDC-BT5**U)

on the Bluetooth device.

“PAIRING”

KNOB” appears on the display.

“PASS XXXXXX” Device name “PRESS” “VOLUME

• For some Bluetooth devices, you may need to enter the Personal

Identification Number (PIN) code immediately after searching.

3 Press the volume knob to start pairing.

“PAIRING OK” appears when pairing is completed.

Once pairing is completed, Bluetooth connection is established automatically.

•

• This unit supports Secure Simple Pairing (SSP).

• Up to five devices can be registered (paired) in total.

• Once the pairing is completed, the Bluetooth device will remain registered in the unit even if you reset the unit. To delete the paired device,

• A maximum of two Bluetooth phones and one Bluetooth audio device can be connected at any time.

However, while in BT AUDIO source, you can connect to five Bluetooth

audio devices and switch between these five devices.

• Some Bluetooth devices may not automatically connect to the unit after pairing. Connect the device to the unit manually.

• Refer to the instruction manual of the Bluetooth device for more information.

: “BT1” and/or “BT2” indicator on the faceplate lights up.

: “BT1” and/or “BT2” on the display window lights up.

16, [DEVICE DELETE]

( 17)

Auto Pairing

When you connect iPhone/iPod touch/Android device to the USB input terminal, pairing request (via Bluetooth) is automatically activated.

Press the volume knob to pair once you have confirmed the device name.

Automatic pairing request is activated only if: – Bluetooth function of the connected device is turned on. –

[AUTO PAIRING]

– KENWOOD MUSIC PLAY application is installed on the Android device

(

8) and

is set to

[BROWSE MODE]

[ON]. ( 16)

is selected.

( 9)

ENGLISH

BLUETOOTH®

BLUETOOTH — Mobile phone

Receive a call

When there is an incoming call:

• flashes.

• The unit answers the call automatically if is set to a selected time.

During a call:

• the settings made for illuminates in green color.

• If you turn off the unit or detach the faceplate, the Bluetooth connection is disconnected.

The following operations may differ or not available depending on the connected phone.

ZONE 2 illuminates in green color and

( 14)

ZONE 1 illuminates according to

[DISPLAY] ( 22)

[AUTO ANSWER]

and ZONE 2

To On the faceplate On the remote control

First incoming call....

Answer a call

Reject a call

End a call

While talking on the first incoming call...

Answer another incoming call and hold the current call

Reject another incoming call

While having two active calls...

End current call and activate held call

Swap between the current call and held call

Adjust the phone volume

[00]

[35]

(Default:

Switch between hands-free and private talk modes

[15]

)

Press

or the volume knob or one of the number buttons (1 to 6).

Press

Turn the volume knob during a call.

• This adjustment will not

affect the volume of the other sources.

Press

• Operations may vary

according to the connected Bluetooth device.

. Press .

during a call.

Press

( Not available )

ENGLISH

BLUETOOTH®

Improve the voice quality

While talking on the phone...

1 Press the volume knob to enter

[FUNCTION]

2 Turn the volume knob to select an item (see the following table), then press

the knob.

3 Repeat step 2 until the desired item is selected or activated. 4 Press and hold to exit.

To return to the previous setting item, press .

Default:

MIC GAIN –10

NR LEVEL –5

ECHO CANCEL –5

to

+10(–4

):The sensitivity of the microphone increases as the number increased.

to+5(0):Adjust the noise reduction level until the least noise is being heard during

a phone conversation.

to+5(0):Adjust the echo cancellation delay time until the least echo is being heard

during a phone conversation.

Make the settings for receiving a call

Press to enter Bluetooth mode.

1 2 Turn the volume knob to select an item (see the following table), then press

the knob.

3 Repeat step 2 until the desired item is selected or activated. 4 Press and hold to exit.

To return to the previous setting item, press .

Default:

SETTINGS

AUTO ANSWER

BATT/SIGNAL

Functionality depends on the type of the phone used.

to30:The unit answers incoming call automatically in the selected time (in seconds).;

OFF

:Cancels.

(For )

AUTO

:Shows the strength of the battery and signal when the unit detects a Bluetooth

device and the Bluetooth device is connected.;

ENGLISH

OFF

:Cancels. Clock time is shown.

Make a call

You can make a call from the call history, phonebook, or dialing the number. Call by voice is also possible if your mobile phone has the feature.

1 Press to enter Bluetooth mode.

“(First device name)” appears.

• If two Bluetooth phones are connected, press again

to switch to another phone.

“(Second device name)” appears. 2 Turn the volume knob to select an item (see the

following table), then press the knob.

3 Repeat step 2 until the desired item is selected/

activated or follow the instructions stated on the selected item.

4 Press and hold to exit.

To return to the previous setting item, press .

CALL HISTORY

(Applicable only if the phone supports PBAP.)

Press the volume knob to select a name or a phone

number.

• “MISSED” is shown on the lower part of the display to indicate the previous call status.

indicates call made, “M” indicates call missed.

• Press (NUMBER or NAME).

• “NO DATA” appears if there is no recorded call history.

Press the volume knob to call.

: “INCOMING”, “OUTGOING”, or

: “I” indicates call received, “O”

DISP

to change the display category

BLUETOOTH®

PHONE BOOK

NUMBER DIAL

VOICE

BATT LOW

NO SIGNAL/LOW/MID/MAX*:Shows the strength of the current received signal.

Functionality depends on the type of the phone used.

(Applicable only if the phone supports PBAP.)

Turn the volume knob quickly to enter alphabet search mode (if the

phonebook contains many contacts).

The first menu (ABCDEFGHIJK) appears.

• To go to the other menu (LMNOPQRSTUV or WXYZ1

• To select the desired first letter, turn the volume knob or press then press the knob.

Select “1” to search with numbers and select “

Turn the volume knob to select a name, then press the knob.

Turn the volume knob to select a phone number, then press the knob to call.

•

The phonebook of the connected phone is automatically transferred to the unit

when pairing.

•

Contacts are categorized as: HOME, OFFICE, MOBILE, OTHER, GENERAL or HM

(home), OF (office), MO (mobile), OT (other), GE (general)

•

This unit can display only non-accent letters. (Accent letters such as “Ú” is

shown as “U”.)

Turn the volume knob to select a number (0 to 9) or character ( , #, +).

Press

S/T

Repeat steps

Press the volume knob to call.

(or using the remote control)

Press the number buttons (0 to 9) to enter the phone number.

Press to call.

Speak the name of the contact you want to call or the voice command to control the phone functions.

MID/FULL*:Shows the strength of the battery.

to move the entry position.

and 2 until you finish entering the phone number.

( Make a call using voice recognition)

), press

J / K

S/T

” to search with symbols.

Make a call using voice recognition

Press and hold to activate the voice recognition of the

connected phone.

2 Speak the name of the contact you want to call or the voice

command to control the phone functions.

• Supported Voice Recognition features vary for each phone. Refer to the instruction manual of the connected phone for details.

• This unit also supports the intelligent personal assistant function of iPhone.

Settings in memory

Store a contact in memory

You can store up to 6 contacts into the number buttons (1 to 6).

1 Press to enter Bluetooth mode. 2 Turn the volume knob to select

[NUMBER DIAL]

, then press the knob.

[CALL HISTORY], [PHONE BOOK]

3 Turn the volume knob to select a contact or enter a phone

number.

If a contact is selected, press the volume knob to show the

phone number.

4 Press and hold one of the number buttons (1 to 6).

“STORED” appears when the contact is stored. To erase a contact from the preset memory, select

in step

2 and store a blank number.

[NUMBER DIAL]

Make a call from memory

Press to enter Bluetooth mode.

1 2 Press one of the number buttons (1 to 6). 3 Press the volume knob to call.

“NO MEMORY” appears if there is no contacts stored.

ENGLISH

BLUETOOTH®

Other settings

Press the volume knob to enter

[FUNCTION]

2 Turn the volume knob to select an item (see the following table), then

press the knob.

3 Repeat step 2 until the desired item is selected/activated or follow the

instructions stated on the selected item.

4 Press and hold to exit.

To return to the previous setting item, press .

Default:

BT MODE

PHONE SELECT

AUDIO SELECT

DEVICE DELETE

PIN CODE EDIT (0000)

RECONNECT ON

AUTO PAIRING ON

INITIALIZE YES

Selects the phone or audio device to connect or disconnect. “

” appears in front of the device name when connected.

“

“ appears in front of the current playback audio device.

•

You can only connect a maximum of two Bluetooth phones and one Bluetooth

audio device at any time.

Turn the volume knob to select a device to delete, then press the knob.

Turn the volume knob to select

Changes the PIN code (up to 6 digits).

Turn the volume knob to select a number.

Press S/T to move the entry position.

Repeat steps

Press the volume knob to confirm.

:The unit automatically reconnect when the last connected Bluetooth device is

within range.;

:The unit automatically pair supported Bluetooth device (iPhone/iPod touch/ Android device) when it is connected through USB input terminal.Depending on the operating system of the connected device, this function may not work. ;

OFF

:Initializes all the Bluetooth settings (including stored pairing, phonebook,

and etc.).;

:Cancels.

and 2 until you finish entering the PIN code.

OFF

:Cancels.

[YES]

[NO]

, then press the knob.

Bluetooth test mode

You can check the connectivity of the supported profile between the Bluetooth device and the unit.

• Make sure there is no Bluetooth device paired.

1 Press and hold .

“PLEASE PAIR YOUR PHONE PIN 0000” appears.

2 Search and select this unit model name (KDC-BT6**U/

KDC-BT5**U) on the Bluetooth device.

3 Operate the Bluetooth device to confirm pairing.

“TESTING” flashes on the display.

The connectivity result (OK or NG) appears after the test.

PAIRING: Pairing status HF CNT: Hands-Free Profile (HFP) compatibility AUD CNT: Advanced Audio Distribution Profile (A2DP)

PB DL: Phonebook Access profile (PBAP) compatibility

To cancel test mode, press and hold

compatibility

to turn off the unit.

ENGLISH

BLUETOOTH®

BLUETOOTH — Audio

While in BT AUDIO source, you can connect to five Bluetooth audio devices and switch between these five devices.

Audio player via Bluetooth

Press repeatedly (or press SRC on the remote control) to select BTAUDIO.

2 Operate the Bluetooth audio player to start playback.

To On the faceplate On the remote control

Playback/pause

Select group or folder

Reverse/Forward skip

Reverse/Fast-forward

Repeat play Press

Random play Press and hold

Select a file from a folder/list

Switch between connected Bluetooth audio devices

Pressing the “Play” key on the connected device itself also causes switching of sound output from the device.

Operations and display indications may differ according to their availability on the connected device.

Press

Press J / K.

Press S/T. Press S/

Press and hold S/T.

ALL REPEAT, FILE REPEAT, REPEAT OFF

ALL RANDOM

• Press

Refer to “Select a file from a folder/list” on page 9.

Press 5.

. Press

repeatedly.

to select

RANDOM OFF

Press

Press and hold S/

( Not available )

/ .

Settings to use KENWOOD Remote application

KENWOOD Remote application is designed to control the KENWOOD car receiver’s operations from the iPhone/ iPod (via Bluetooth or via USB input terminal) or Android smartphone (via Bluetooth).

Preparation: Install the latest version of KENWOOD Remote application on your device before connecting. For more information, visit <www.kenwood.com/cs/ce/>.

1 Press the volume knob to enter

[FUNCTION]

2 Turn the volume knob to select an item (see the

following table), then press the knob.

3 Repeat step 2 until the desired item is selected or

activated.

4 Press and hold to exit.

To return to the previous setting item, press .

REMOTE APP

SELECT

IOS YES:Selects iPhone/iPod to use the application via Bluetooth

ANDROID YES

ANDROID LIST

Select the device (IOS or ANDROID) to use the application.

or connected via USB input terminal.; If IOS is selected, select iPod BT source (or iPod USB if your iPhone/iPod is connected via USB input terminal) to activate the application.

•

The connectivity of the application will be interrupted or

disconnected if: – You change from iPod BT source to any playback

source connected via the USB input terminal.

– You change from iPod USB source to iPod BT source.

:Selects Android smartphone to use the application via

Bluetooth.;

: Cancels.

*:Selects the Android smartphone to use from the list.

Default:

NO:Cancels.

ENGLISH

BLUETOOTH®

STATUS

Displayed only when

You can listen to the songs on the iPhone/iPod via Bluetooth on this unit.

Press repeatedly to select iPodBT.

• You can operate the iPod/iPhone in the same way as iPod/iPhone via USB

• If you plug in an iPhone/iPod to the USB input terminal while listening to

Internet radio via Bluetooth

You can listen to Pandora on the iPhone/iPod/Android device via Bluetooth on this unit.

• Make sure the USB input terminal is not connected to any device.

Preparation:

Select

1 Open the Pandora application on your device. 2 Connect your device via Bluetooth connection. 3 Press repeatedly to select PANDORA (for iPhone/iPod) or

The source switches and broadcast starts automatically.

• You can operate Pandora in the same way as Pandora via USB input terminal.

Shows the status of the selected device.

IOS CONNECTED

via Bluetooth or USB input terminal.

IOS NOT CONNECTED ANDROID CONNECTED

smartphone connected via Bluetooth.

ANDROID NOT CONNECTED

: You are able to use the application using the iPhone/iPod connected

: No IOS device is connected to use the application.

: You are able to use the application using the Android

: No Android device is connected to use the application.

[ANDROID]

[SELECT]

is set to

[YES]

Listen to iPhone/iPod via Bluetooth

input terminal.

iPodBT source, the source automatically change to iPodUSB. Press select iPodBT if the device is still connected via Bluetooth.

( 8)

Listen to Pandora

[ON]

for

[PANDORA SRC]

PANDORA BT (for Android device).

( 10)

[SOURCE SELECT]. ( 5)

( 12)

ENGLISH

AUDIO SETTINGS

While listening to any source...

1 Press the volume knob to enter 2 Turn the volume knob to select an item (see the following

table), then press the knob.

3 Repeat step 2 until the desired item is selected or activated. 4 Press and hold to exit.

(or using the remote control)

1 Press AUD to enter

[AUDIO CONTROL]

2 Press J / K to select an item, then press .

To return to the previous setting item, press

AUDIO CONTROL

SUB-W LEVEL

MANUAL EQ

BAND1 LEVEL

LEVEL

BASS EXTEND ON

BAND2 LEVEL BAND13 LEVEL

Q FACTOR 1.35/1.50/2.00

PRESET EQ NATURAL/ROCK/POPS/EASY/TOP40/JAZZ/POWERFUL

LEVEL –50

output level.

The sound elements (frequency level, tone level, Q factor) are preset into each selection (

LEVEL–9

to memorize for each source. (Before making an adjustment, select the source you want to adjust.)

:Turns on the extended bass.;

LEVEL–9

to memorize for each source. (Before making an adjustment, select the source you want to adjust.)

USER

: Selects a preset equalizer suitable to the music genre.

(Select

[USER]

[FUNCTION]

LEVEL +10 (LEVEL 0

BAND1 LEVEL

LEVEL +9 (LEVEL 0

:Adjust the quality factor.

to use the settings made in

):Adjusts the level to

Default:

): Adjusts the subwoofer

BAND13 LEVEL

OFF

:Cancels.

[MANUAL EQ]

AUDIO SETTINGS

BASS BOOST LEVEL1/LEVEL2/LEVEL3/LEVEL4/LEVEL5

LOUDNESS LEVEL1/LEVEL2

SUBWOOFER SET ON

FADER

BALANCE L15

VOLUME OFFSET –15

SOUND EFFECT

SOUND RECNSTR

(Sound reconstruction)

SPACE ENHANCE

SND REALIZER LEVEL1/LEVEL2/LEVEL3

STAGE EQ LOW/MIDDLE/HIGH

DRIVE EQ ON

SPEAKER SIZE

X’OVER

DTA SETTINGS

CAR SETTINGS

LV5

:Selects your preferred bass boost level.;

LV1/LV2

frequencies boost to produce a well-balanced sound at a low volume level.;

OFF

:Cancels.

:Turns on the subwoofer output.;

(Not applicable if 3-way crossover is selected.)

R15

F15 (0

):Adjusts the rear and front speaker output balance.

R15 (0

):Adjusts the left and right speaker output balance.

to +6 (0):Preset the initial volume level of each source. (Before

adjustment, select the source you want to adjust.)

(Not applicable for TUNER source and AUX source.)

:Creates realistic sound by compensating the high-frequency components and restoring the rise-time of the waveform that are lost in audio data compression.;

(Not applicable for TUNER source.)

SMALL/MEDIUM/LARGE

sound space.;

more realistic.;

position heard from the speakers.;

car or running noise of the tyres.;

Depending on the crossover type you have selected crossover or 3-way crossover setting items will be shown By default, 2-way crossover type is selected.

For settings,

OFF

: Boosts the frequency to reduce the noise heard from outside the

21, Digital Time Alignment Settings.

:Selects your preferred low and high

OFF

:Cancels.

SML/MED/LRG

:Cancels.

LV1/LV2/LV3

:Cancels.

LOW/MID/HI

:Virtually adjust the sound

OFF

:Cancels.

LV1/LV2/LV3/LV4

OFF

:Cancels.

:Virtually enhances the

:Virtually makes the sound

:Cancels.

( 5)

, 2-way

( 19, 20)

•

: For 2-way crossover:

only if

[SWITCH PREOUT]

• [SUB-W LEVEL]

is set to

is selectable only if

[SUB-W LEVEL]/[SUBWOOFER SET]

[SUB-W]. ( 4)

[SUBWOOFER SET]

is set to

Crossover settings

Below are the available setting items for 2-way crossover and 3-way crossover.

SPEAKER SIZE

Selects according to the connected speaker size for optimum performance.

•

The frequency and slope settings are automatically set for the crossover of the selected speaker.

•

When 2-way crossover is selected, if

[FRONT], [REAR]

the speaker is not available.

• When 3-way crossover is selected, if

[SPEAKER SIZE]

X ‘ OVER

• [FRQ]

crossover frequency for the selected speakers (high pass filter or low pass filter).

[THROUGH]

•

[F - HPF SLOPE]/[R - HPF SLOPE]/[SW LPF SLOPE]/[HPF SLOPE]/[LPF SLOPE]/[SLOPE]:

Adjusts the crossover slope. Selectable only if a setting other than crossover frequency.

• [SW LPF PHASE]/[PHASE]:

line with the other speaker output.

• [GAIN LEFT]/[GAIN RIGHT]/[F - HPF GAIN]/[R - HPF GAIN]/[SW LPF GAIN]/[GAIN]:

Adjusts the output volume of the selected speaker.

and

[SUBWOOFER]

, the

[X’OVER]

setting of

[F - HPF FRQ]/[R - HPF FRQ]/[SW LPF FRQ]/[HPF FRQ]/[LPF FRQ]

is selected, all signals are sent to the selected speakers.

Selects the phase of the speaker output to be in

[NONE]

for

[SPEAKER SIZE]

[NONE]

[WOOFER]

is selected for

is not available.

[THROUGH]

, the

is selected for the

[ON]

[X ‘ OVER]

is selectable

[TWEETER]

[WOOFER]

: Adjusts the

ENGLISH

setting of

AUDIO SETTINGS

2-way crossover setting items

SPEAKER SIZE

FRONT SIZE

8CM/10CM/12CM/13CM/16CM/17CM/18CM/4×6 5×7/6×8/6×9/7×10

TWEETER

SMALL/MIDDLE/LARGE/NONE

(not connected)

REAR 8CM/10CM/12CM/13CM/16CM/17CM/18CM/4×6/5×7/6×8/6×9/7×10/

NONE

(not connected)

SUBWOOFER

16CM/20CM/25CM/30CM/38CM OVER/NONE

(not connected)

X ' OVER

TWEETER FRQ

1KHZ/1.6KHZ/2.5KHZ/4KHZ/5KHZ/6.3KHZ/8KHZ 10KHZ/12.5KHZ

GAIN LEFT

GAIN RIGHT

FRONT HPF F - HPF FRQ

–8

30HZ/40HZ/50HZ/60HZ/70HZ/80HZ/90HZ/100HZ 120HZ/150HZ/180HZ/220HZ/250HZ/THROUGH

F - HPF SLOPE

F - HPF GAIN

–6DB/–12DB/–18DB/–24DB

–8

REAR HPF R - HPF FRQ

(Refer

FRONT HPF

R - HPF SLOPE

settings above.)

R - HPF GAIN

SUBWOOFER

LPF

Selectable only when and

SW LPF FRQ 30HZ/40HZ/50HZ/60HZ/70HZ/80HZ/90HZ/100HZ

SW LPF SLOPE

SW LPF PHASE

SW LPF GAIN –8

[SUBWOOFER SET]

[SWITCH PREOUT]

is set to

120HZ/150HZ/180HZ/220HZ/250HZ/THROUGH

–6DB/–12DB/–18DB/–24DB

REVERSE

(180°)/

NORMAL

is set to

[SUB-W] ( 4)

[ON]. ( 19)

ENGLISH

(0°)

(for ),

3-way crossover setting items

SPEAKER SIZE

TWEETER

MID RANGE

WOOFER

SMALL/MIDDLE/LARGE

8CM/10CM/12CM/13CM/16CM/17CM/18CM/4×6/5×7/6×8/6×9

16CM/20CM/25CM/30CM/38CM OVER/NONE

(not connected)

X ' OVER

TWEETER HPF FRQ

1KHZ/1.6KHZ/2.5KHZ/4KHZ/5KHZ/6.3KHZ

8KHZ/10KHZ/12.5KHZ

PHASE

GAIN –8

MID RANGE HPF FRQ

HPF SLOPE

LPF FRQ

SLOPE

–6DB/–12DB

REVERSE

(180°)/

NORMAL

(0°)

30HZ/40HZ/50HZ/60HZ/70HZ/80HZ/90HZ 100HZ/120HZ/150HZ/180HZ/220HZ/250HZ THROUGH

–6DB/–12DB

1KHZ/1.6KHZ/2.5KHZ/4KHZ/5KHZ/6.3KHZ

8KHZ/10KHZ/12.5KHZ/THROUGH

LPF SLOPE

PHASE

GAIN –8

WOOFER

LPF FRQ 30HZ/40HZ/50HZ/60HZ/70HZ/80HZ/90HZ

–6DB/–12DB

REVERSE

(180°)/

NORMAL

(0°)

100HZ/120HZ/150HZ/180HZ/220HZ/250HZ

THROUGH

SLOPE

PHASE

Selectable only when

GAIN –8

–6DB/–12DB

REVERSE

[SUBWOOFER SET]

is set to

(180°)/

NORMAL

(0°)

[ON]. ( 19)

+ 44 hidden pages

Kenwood KDC-BT610U, KDC-BT10U Instruction Manual

Specifications and Main Features

Frequently Asked Questions

User Manual