Record the serial number, found on the back of the unit, in the
spaces designated on the warranty card, and in the space provided
below. Refer to the model and serial numbers whenever you
call upon your Kenwood dealer for information or service on the
product.
Model KDC-268U/ KDC-168U/ KDC-138U/ KDC-118/ KDC-MP168U
Serial number
US Residents Only
Register Online
Register your Kenwood product at http://www.kenwood.com/usa/
and cancel the demonstration
2 Set the clock and date
3 Set the initial settings
RADIO 5
CD/USB/iPod/ANDROID 7
Pandora®
(for / )
10
iHeartRadio®
(for / )
11
AUX 12
AUDIO SETTINGS 13
DISPLAY SETTINGS 14
TROUBLESHOOTING 15
REFERENCES 17
Maintenance
More information
INSTALLATION/
CONNECTION 20
SPECIFICATIONS 22
2
ENGLISH
IMPORTANT
•
To ensure proper use, please read through this manual before using this product. It is especially important that you read and observe
Warning and Caution in this manual.
•
Please keep the manual in a safe and accessible place for future reference.
WARNING
•
Do not operate any function that takes your attention away from safe driving.
•
Do not ingest the battery, Chemical Burn Hazard
The remote control supplied with this product contains a coin/button cell battery.
If the coin/button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death.
Keep new and used batteries away from children.
If the battery compartment does not close securely, stop using the product and keep it away from children.
If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.
Caution
Volume setting:
•
Adjust the volume so that you can hear sounds outside the car to prevent accidents.
•
Lower the volume before playing digital sources to avoid damaging the speakers by the sudden increase of the output level.
General:
•
Avoid using the external device if it might hinder safe driving.
•
Make sure all important data has been backed up. We shall bear no responsibility for any loss of recorded data.
•
Never put or leave any metallic objects (such as coins or metal tools) inside the unit, to prevent a short circuit.
•
If a disc error occurs due to condensation on the laser lens, eject the disc and wait for the moisture to evaporate.
•
Depending on the types of cars, the antenna will automatically extend when you turn on the unit with the antenna control wire connected
( 21)
. Turn off the unit or change the source to STANDBY when parking at a low ceiling area.
Remote control (RC-406):
•
Do not leave the remote control in hot places such as on the dashboard.
•
The Lithium battery is in danger of explosion if replaced incorrectly. Replace it only with the same or equivalent type.
•
The battery pack or batteries shall not be exposed to excessive heat such as sunshine, fire or the like.
How to read this manual
•
Operations are explained mainly using buttons on the faceplate of .
•
English indications are used for the purpose of explanation. You can select the display language from the
•
[XX]
indicates the selected items.
•
( XX)
indicates references are available on the stated page.
[FUNCTION]
menu.
( 5)
BASICS
Faceplate
Loading slot
Volume knob
Detach button
How to resetAttachDetach
ToOn the faceplateOn the remote control
Turn on the power
Adjust the volumeTurn the volume knob.Press
Select a source
Change the display information*Press DISP repeatedly.
*
: You can also turn off the display information by pressing
Press
• Press and hold to turn off the power.
Press
Display window
: Flashes when the unit enters searching status.
Your preset adjustments will be
erased except stored radio stations.
.
repeatedly.
( 19)
DISP
repeatedly.
Remote control (RC-406)
*
Not used
How to replace the battery
Press and hold SRC to turn off the power.
( Pressing SRC does not turn on the power. )
• Press and hold
the volume to 15.
Press ATT during playback to attenuate the sound.
• Press again to cancel.
Press SRC repeatedly.
( Not available )
or .
Remote sensor (Do not
expose to bright sunlight.)
Pull out the
insulation sheet
when using for
the first time.
to continuously increase
ENGLISH
3
GETTING STARTED
1
Select the display language and cancel the
demonstration
When you turn on the power (or after you reset the unit), the
display shows: “SEL LANGUAGE”
1 Turn the volume knob to select
(Spanish), then press the knob.
[ENG]
is selected for the initial setup.
Then, the display shows: “CANCEL DEMO”
“VOLUME KNOB”.
2 Press the volume knob.
[YES]
is selected for the initial setup.
3 Press the volume knob again.
“DEMO OFF” appears.
2
Set the clock and date
1
Press the volume knob to enter
2
Turn the volume knob to select
To adjust the clock
3
Turn the volume knob to select
knob.
4
Turn the volume knob to make the settings, then press the knob.
Hour Minute
5
Turn the volume knob to select
knob.
6
Turn the volume knob to select
knob.
4
ENGLISH
“PRESS” “VOLUME KNOB”
[ENG]
(English) or
[FUNCTION]
[CLOCK]
, then press the knob.
[CLOCK ADJUST]
[CLOCK FORMAT]
[12H]
or
[24H]
[SPA]
“PRESS”
.
, then press the
, then press the
, then press the
To set the date
7 Turn the volume knob to select
8 Turn the volume knob to select
9 Turn the volume knob to select
[DATE FORMAT]
[DD/MM/YY]
[DATE SET]
, then press the knob.
, then press the knob.
or
[MM/DD/YY]
, then press the knob.
10 Turn the volume knob to make the settings, then press the knob.
Day
Month Year or Month Day Year
11 Press and hold to exit.
To return to the previous setting item, press
3
Set the initial settings
1
Press repeatedly to enter STANDBY.
2 Press the volume knob to enter
[FUNCTION]
.
.
3 Turn the volume knob to select an item (see the following table), then press
the knob.
4 Repeat step 3 until the desired item is selected or activated.
5 Press and hold to exit.
To return to the previous setting item, press
AUDIO CONTROL
SWITCH PREOUT
SP SELECT
DISPLAY
EASY MENU
REAR/SUBWOOFER
connected to the line out terminals on the rear (through an external amplifier).
OFF/ 5/4/ 6 × 9/6/ OEM
6×9inches or 6inches) or OEM speakers for optimum performance.
(For )
When entering
ON
:ZONE 1 illumination changes to white color.;
OFF
:ZONE 1 illumination remains as
•
ZONE 2 illumination changes to white color when you enter
irregardless of the
•
Refer to the illustration on page 14 for ZONE identification.
or
REAR/SUB-W: Selects whether rear speakers or a subwoofer are
: Selects according to the speaker size (5inches or 4inches,
[FUNCTION]
...
[EASY MENU]
.
[COLOR SELECT]
setting.
color.
( 15)
[FUNCTION]
Default:
( 21)
,
XX
GETTING STARTEDRADIO
TUNER SETTING
PRESET TYPE
SYSTEM
KEY BEEP
SOURCE SELECT
PANDORA SRC
IHEART SRC
BUILT-IN AUX
CD READ
F/W UPDATE
UPDATE SYSTEM
F/W UP xxxx
CLOCK
CLOCK DISPLAY
ENGLISH
ESPANOL
NORMAL
:Memorizes one station for each preset button in each band
(FM1/FM2/FM3/AM).;
button, regardless of the selected band.
ON
:Activates the keypress tone.;
(For / )
ON
:Enables PANDORA in source selection.;
(For / )
ON
:Enables IHEARTRADIO in source selection.;
ON
:Enables AUX in source selection.;
1
:Automatically distinguishes between audio file disc and music CD.;
2
:Forces to play as a music CD. No sound can be heard if an audio file disc
is played.
(except for )
YES
:Starts upgrading the firmware.; NO:Cancels (upgrading is not
activated).
For details on how to update the firmware, visit
<www.kenwood.com/cs/ce/>.
ON
:The clock time is shown on the display even when the unit is turned
off.;
OFF
:Cancels.
Select the display language for
if applicable.
By default,
[ENGLISH]
MIX
:Memorizes one station for each preset
OFF
:Deactivates.
OFF
:Disables.
OFF
:Disables.
OFF
:Disables.
[FUNCTION]
is selected.
menu and music information
( 12)
( 10)
( 11)
Search for a station
1
Press repeatedly to select TUNER.
2 Press repeatedly (or press / on the remote
control) to select FM1/FM2/FM3/AM.
3 Press S/T (or press S/ on the remote control) to
search for a station.
• To change the searching method for S/T: Press
repeatedly.
AUTO1 : Automatically search for a station.
AUTO2 : Search for a preset station.
MANUAL : Manually search for a station.
• To store a station: Press and hold one of the number buttons (1to6).
• To select a stored station: Press one of the number buttons (1to6) (or
press one of the number buttons (1to6) on the remote control).
Direct Access Tuning
1 Press DIRECT to enter Direct Access Tuning.
2 Press the number buttons to enter a frequency.
3 Press to search for a station.
• To cancel, press
• If no operation is done for 10seconds after step
is automatically canceled.
(using the remote control)
or DIRECT.
2, Direct Access Tuning
ENGLISH
5
RADIO
Other settings
1
Press the volume knob to enter
[FUNCTION]
.
2 Turn the volume knob to select an item (see the following table), then press
the knob.
3 Repeat step 2 until the desired item is selected or activated.
4 Press and hold to exit.
To return to the previous setting item, press
TUNER SETTING
AUTO
MEMORY
MONO SET
NEWS SET
REGIONAL
AF SET
TI
PTY SEARCH
YES
:Automatically starts memorizing 6 stations with good reception.; NO:Cancels.
•
Selectable only if
ON
:Improves the FM reception, but the stereo effect may be lost.;
(For )
ON
: The unit will temporarily switch to News Programme if available. ;
(For )
ON
: Switches to another station only in the specific region using the “AF” control.;
OFF
:Cancels.
(For )
ON
: Automatically searches for another station broadcasting the same program in the
same Radio Data System network with better reception when the current reception is
poor.;
OFF
(For / )
ON
:Allows the unit to temporarily switch to Traffic Information if available (“TI” lights
up).;
OFF
(For / )
Select the available Program Type (see the following), then, press
:Cancels.
:Cancels.
[NORMAL]
is selected for
.
[PRESET TYPE]. ( 5)
OFF
:Cancels.
OFF
S
/T to start.
Default:
: Cancels.
CLOCK
TIME SYNC
Available Program Type for
(For )
SPEECH : NEWS, INFORM
XX
MUSIC
(For )
SPEECH : NEWS, AFFAIRS, INFO
MUSIC
The unit will search for the Program Type categorized under
• If the volume is adjusted during reception of traffic information
or news bulletin, the adjusted volume is memorized
automatically. It will be applied the next time traffic
information or news bulletin is turned on.
(For / )
ON
:Synchronizes the unit’s time to the Radio Broadcast Data
The source changes automatically and
playback starts.
CD
M
Eject disc
Label side
USB input terminal
USB
CA-U1EX (max.: 500mA)
(optional accessory)
iPod/iPhone
KCA-iP102/KCA-iP103
(optional accessory)
or accessory of the iPod/
2
*
iPhone
3
ANDROID
*
Micro USB 2.0 cable
(commercially available)
Selectable sources:
/ :
/ :
:
CD
CD/USB/iPod/ANDROID
CD/USB/ANDROID
• To directly select USB/iPod/ANDROID source, press iPod USB or APP USB.
ToOn the faceplateOn the remote control
Playback/pausePress .
4
Reverse/Fast-forward
Select a track/file
Select a folder
1
*
1
*
KCA-iP102 : 30-pin type, KCA-iP103 : Lightning type
2
*
Do not leave the cable inside the car when not using.
3
*
When connecting an Android device, “Press [VIEW] to install KENWOOD MUSIC PLAY APP” is shown. Follow the instructions
*
Press and hold S/T.Press and hold S/.
Press S/T.Press S/
5
*
Press J/K.
Press
Press
.
.
/.
to install the application. You can also install the latest version of KENWOOD MUSIC PLAY application on your Android device
before connecting. For more information, visit <www.kenwood.com/cs/ce/>.
4
*
For ANDROID: Applicable only when
5
*
For CD: Only for MP3/WMA files. This does not work for iPod/ANDROID.
: Control iPod using the iPod itself. However, you can still play/
MODE OFF
While in ANDROID source, press iPod USB or APP USB repeatedly.
BROWSE MODE
HAND MODE
pause, file skip, fast-forward or reverse from this unit.
: Control iPod from this unit.
: Control Android device from this unit via KENWOOD
MUSIC PLAY application installed in the Android device.
: Control Android device using the Android device itself via
other media player applications installed in the Android
device. However, you can still play/pause and file skip from
this unit.
Select a file from a folder/list
For iPod/ANDROID, applicable only when
selected.
[MODE OFF]/[BROWSE MODE]
is
1 Press .
2 Turn the volume knob to select a folder/list, then press the knob.
3 Turn the volume knob to select a file, then press the knob.
Quick Search
If you have many files, you can search through them quickly.
Turn the volume knob quickly to browse through the list quickly.
Skip Search
Press S/T to search at a preset skip search ratio. ( 9,
SEARCH]
• Pressing and holding S/T searches at a 10
Alphabet search
You can search for a file according to the first character.
For iPod source
(applicable only for CD, USB and ANDROID source)
(applicable only for iPod and ANDROID source)
)
(applicable only for iPod and ANDROID source)
%
[SKIP
ratio.
1 Turn the volume knob quickly to enter character search.
2 Turn the volume knob to select the character.
• Select “
3 Press S/T to move to the entry position.
” to search for a character other than AtoZ, 0to9.
*
• You can enter up to 3characters.
4 Press the volume knob to start searching.
For ANDROID source
1 Press J/K to enter character search.
2 Turn the volume knob to select the character.
^A^: Upper case letters (A to Z)
_A_: Lower case letters (a to z)
-0-: Numbers (0 to 9)
: Character other than AtoZ, 0to9
***
3 Press the volume knob to start searching.
8
ENGLISH
CD/USB/iPod/ANDROID
• To return to the root folder/first file/top menu, press 5.
• To return to the previous setting item, press
• To cancel, press and hold
Direct Music Search
(using the remote control)
.
1 Press DIRECT.
2 Press the number buttons to enter a track/file number.
3 Press to search for music.
• To cancel, press
• Not available if Random Play is selected.
• Not applicable for iPod and ANDROID source.
Select music drive
While in USB source, press iPod USB or APP USB repeatedly.
Stored songs in the following drive will be played back.
• Selected internal or external memory of a smartphone (Mass Storage
Class).
• Selected drive of a multiple drives device.
or DIRECT.
(except for )
Listen to TuneIn Radio/TuneIn Radio Pro/Aupeo
(for / )
While listening to TuneIn Radio, TuneIn Radio Pro or Aupeo, connect the
iPod/iPhone to the USB input terminal of the unit.
• The unit will output the sound from these applications.
.
Other settings
1
Press the volume knob to enter
[FUNCTION]
.
2 Turn the volume knob to select an item (see the following table),
then press the knob.
3 Repeat step 2 until the desired item is selected or activated.
4 Press and hold to exit.
[DRIVE 1]
.
to
[DRIVE 5]
Default:
) is selected
To return to the previous setting item, press
USB
MUSIC DRIVEDRIVE CHANGE
automatically and playback starts.
Repeat steps
SKIP SEARCH0.5%/1%/5%/10%
the skip search ratio over the total files.
:The next drive (
1
to 3 to select the following drives.
: While listening to iPod or ANDROID source, selects
XX
ENGLISH
9
Pandora®
Preparation:
Install the latest version of the Pandora application on your device
(iPhone/iPod touch), then create an account and log in to Pandora.
• Select
[ON]
(for / )
for
[PANDORA SRC]
in
[SOURCE SELECT]. ( 5)
Start listening
1
Open the Pandora application on your device.
2 Connect your device to the USB input terminal.
USB input terminal
1
*
The source changes to PANDORA and broadcast starts.
ToOn the faceplateOn the remote control
Playback/pause
Skip a track
Thumbs up or thumbs
3
*
down
1
*
KCA-iP102 : 30-pin type, KCA-iP103 : Lightning type
2
*
Do not leave the cable inside the car when not using.
3
*
If thumbs down is selected, the current track is skipped.
KCA-iP102/KCA-iP103 (optional accessory)
or accessory of the iPod/iPhone
Press
Press T.
Press J/K.
*
.Press
2
Press
Press
.
/.
Create and save a new station
1
Press .
2 Turn the volume knob to select
3 Turn the volume knob to select
press the knob.
A new station is created based on the artist or current song.
[NEW STATION]
[FROM ARTIST]
, then press the knob.
or
[FROM TRACK]
, then
4 Press and hold one of the number buttons (1to5) to store.
To select a stored station: Press one of the number buttons (1to5).
Search for a registered station
1
Press .
2 Turn the volume knob to select an item, then press the knob.
[BY DATE]
: According to the registered date
[A-Z]
: By alphabetical order
3 Turn the volume knob (or press J / K on the remote control) to
select the desired station.
4 Press the volume knob (press on the remote control) to
confirm.
.
To cancel, press and hold .
Bookmark current song information
Press and hold the volume knob.
“BOOKMARKED” appears and the information is stored to your device.
• The bookmark is available on your Pandora account but not on this
unit.
10
ENGLISH
Pandora®
(for / )
Delete a station
While listening to PANDORA...
1 Press .
2 Turn the volume knob to select
press the knob.
3 Turn the volume knob to select
then press the knob.
[STATION DEL]
[BY DATE]
or
, then
[A-Z]
,
4 Turn the volume knob to select the desired station
to delete, then press the knob.
5 Turn the volume knob to select
the knob.
[YES]
, then press
6 Press and hold to exit.
To return to the previous setting item, press
.
iHeartRadio®
Preparation:
Install the latest version of iHeart Link for KENWOOD application on your device (iPhone/
iPod touch), then create an account and log in to iHeartRadio.
• Select
[ON]
for
[IHEART SRC]
(for / )
in
[SOURCE SELECT]. ( 5)
Start listening
1
Open the iHeart Link application on your device.
2 Connect your device to the USB input terminal.
USB input terminal
1
KCA-iP102/KCA-iP103 (optional accessory)
or accessory of the iPod/iPhone
*
2
*
3 Press repeatedly to select IHEARTRADIO.
Broadcast starts automatically.
ToOn the faceplateOn the remote control
Playback/pause
Skip a track for custom station
Thumbs up or thumbs down
custom station
Create a new/custom stationPress 1.( Not available )
Add to favorite stations for live
station
Scan for live stationPress 3.( Not available )
1
*
KCA-iP102 : 30-pin type, KCA-iP103 : Lightning type
2
*
Do not leave the cable inside the car when not using.
3
*
If thumbs down is selected, the current track is skipped.
3
*
for
Press
Press T.
Press J/K.
Press 2.
.Press
Press
( Not available )
( Not available )
.
.
ENGLISH
11
iHeartRadio®
(for / )
Search for a station
1
Press .
2 Turn the volume knob to select a category, then press the knob.
3 Turn the volume knob (or press J / K on the remote control) to select the
desired station.
4 Press the volume knob (or press on the remote control) to
confirm.
When a city list appears, you can skip cities in alphabetical order.
To cancel, press and hold
.
AUX
Preparation:
Select
[ON]
for
[BUILT-IN AUX]
Start listening
1
Connect a portable audio player (commercially available).
Auxiliary input jack
in
[SOURCE SELECT]. ( 5)
Portable audio player
Skip cities by alphabetical order
While a city list appears during search...
1 Turn the volume knob quickly to enter character search.
2 Turn the volume knob or press S/T to select the character to be
searched for.
3 Press J / K to move to the previous/next page.
4 Press the volume knob to start searching.
To cancel, press and hold
.
Delete a station
While listening to IHEARTRADIO...
1 Press the volume knob to enter
2 Turn the volume knob to select
3 Turn the volume knob to select
4 Turn the volume knob to select
[FUNCTION]
[SYSTEM]
[STATION DEL]
[LIVE]
.
, then press the knob.
or
[CUSTOM]
, then press the knob.
, then press the knob.
5 Turn the volume knob to select the desired station to delete, then press
the knob.
6 Turn the volume knob to select
[YES]
, then press the knob.
7 Press and hold to exit.
To return to the previous setting item, press
12
ENGLISH
.
3.5mm (1/8") stereo mini plug with “L” shaped
connector (commercially available)
2 Press repeatedly to select AUX.
3 Turn on the portable audio player and start playback.
Set the AUX name
While listening to a portable audio player connected to the unit...
1 Press the volume knob to enter
2 Turn the volume knob to select
3 Turn the volume knob to select
knob.
[FUNCTION]
[SYSTEM]
[AUX NAME SET]
.
, then press the knob.
, then press the
4 Turn the volume knob to select an item, then press the knob.
AUX
(default)/
DVD/PORTABLE/GAME/VIDEO/TV
5 Press and hold to exit.
To return to the previous setting item, press
.
AUDIO SETTINGS
While listening to any source...
1 Press the volume knob to enter
For
: Press AUD to enter
2 Turn the volume knob to select an item (see the following table),
then press the knob.
3 Repeat step 2 until the desired item is selected or activated.
4 Press and hold to exit.
To return to the previous setting item, press
(or using the remote control)
1 Press AUD to enter
[AUDIO CONTROL]
2 Press J / K to select an item, then press .
AUDIO CONTROL
SUB-W LEVEL
BASS LEVEL–8
MID LEVEL–8
TRE LEVEL–8
–15
to
to +8 (+2)
to +8 (+1)
to +8 (+1)
+15 (0
[FUNCTION]
)Adjusts the subwoofer output level.
Adjusts the level to memorize for each source. (Before
making an adjustment, select the source you want
to adjust.)
.
[AUDIO CONTROL]
.
directly.
.
Default:
EQ PRO
(This setting is stored to [
BASS ADJUSTBASS CTR FRQ 60HZ/80HZ/100HZ/200HZ
MID ADJUSTMID CTR FRQ0.5KHZ/1.0KHZ/1.5KHZ/2.5KHZ
TRE ADJUSTTRE CTR FRQ10.0KHZ/12.5KHZ/15.0KHZ/17.5KHZ
output to be in line with the speaker output for optimum performance.
(Selectable only if a setting other than
[LPF SUBWOOFER]
to
F15 (0
to
R15 (0
For AUX:
–8
volume level of each source. (Before adjustment, select the source you
want to adjust.)
ON
:Creates realistic sound by compensating the high-frequency
components and restoring the rise-time of the waveform that are lost
in audio data compression.;
[SWITCH PREOUT]
is set to
:Audio signals with frequencies lower than
(180°)/
NORMAL
(0°):Selects the phase of the subwoofer
.)
):Adjusts the rear and front speaker output balance.
):Adjusts the left and right speaker output balance.
to +8(0) ; For other sources: –8 to 0:Preset the initial
is set to
[ON]. ( 13)
[THROUGH]
OFF
:Cancels.
[SUBWOOFER]
is selectable only if
is selected for
is
or
[SUB-W]. ( 4)
DISPLAY SETTINGS
(For )
(For / /
)
(For
Set the dimmer
Press and hold DISP (DIMMER) to turn on or off the dimmer.
• If you have set
and hold this button.
[DIMMER TIME] ( 15)
, it will be canceled once you press
Other settings
1
Press the volume knob to enter
[FUNCTION]
2 Turn the volume knob to select an item
3 Repeat step 2 until the desired item is selected/activated or follow
— 31: Select your preferred brightness level for the selected
zone.
:Select whether to scroll the display information
and
ZONE 2
/preset colors*
[CUSTOM R/G/B]
.
OFF
:Cancels.
[ON]
[OFF]
or
6:00PM; [OFF]: AM6:00
OFF
:Cancels.
separately.
. The color you have
time, then press the
time, then press the
Default:
or
6:00AM
TROUBLESHOOTING
XX
SymptomRemedy
Sound cannot be heard.
“MISWIRING CHECK WIRING
THEN PWR ON” appears.
“PROTECTING SEND SERVICE”
appears.
General
•
Sound cannot be heard.
•
The unit does not turn on.
•
Information shown on the
display is incorrect.
The unit does not work at all. Reset the unit.
•
Radio reception is poor.
•
Static noise while listening
Radio
to the radio.
Disc cannot be ejected.
)
/
/
/
Noise is generated.Skip to another track or change the disc.
Tracks do not play back as
you intended them to play.
“READING” keeps flashing.Do not use too many hierarchical levels or folders.
Elapsed playing time is not
correct.
CD/USB/iPod
Correct characters are not
displayed (e.g. album name).
“NA FILE”Make sure the disc contains supported audio files.
“NO DISC”Insert a playable disc into the loading slot.
•
Adjust the volume to the optimum level.
•
Check the cords and connections.
Turn the power off, then check to be sure the terminals of
the speaker wires are insulated properly. Turn the power
on again.
Send the unit to the nearest service center.
Clean the connectors.
Connect the antenna firmly.
Press and hold
to drop the disc when it is ejected. If this does not solve the
problem, reset the unit.
Playback order is determined when files are recorded.
This is caused by how the tracks are recorded.
•
This unit can only display uppercase letters, numbers,
and a limited number of symbols.
•
Depending on the display language you have selected
( 5)
, some characters may not be displayed correctly.
( 17)
( 3)
M
to forcibly eject the disc. Be careful not
( 3)
( 18)
ENGLISH
15
TROUBLESHOOTING
SymptomRemedy
“TOC ERROR”Make sure the disc is clean and inserted properly.
“PLEASE EJECT”Reset the unit. If this does not solve the problem, consult
“READ ERROR”Copy the files and folders onto the USB device again. If this
“NO DEVICE”Connect a USB device, and change the source to USB again.
“COPY PRO”A copy-protected file is played.
CD/USB/iPod
“NA DEVICE”Connect a supported USB device, and check the
“NO MUSIC”Connect a USB device that contains playable audio files.
“iPod ERROR”
•
Sound cannot
be heard during
playback.
•
Sound output only
from the Android
device.
Cannot playback at
[
BROWSE MODE
ANDROID
“NO DEVICE” or
“READING” keeps
flashing.
16
ENGLISH
your nearest service center.
does not solve the problem, reset the USB device or use
another USB device.
connections.
•
Reconnect the iPod.
•
Reset the iPod.
•
Reconnect the Android device.
•
If in
[HAND MODE]
on the Android device and start playback.
•
If in
[HAND MODE]
application or use another media player application.
•
Restart the Android device.
•
If this does not solve the problem, the connected Android
device is unable to route the audio signal to unit.
•
Make sure KENWOOD MUSIC PLAY APP is installed on the
].
Android device.
•
Reconnect the Android device and select the appropriate
control mode.
•
If this does not solve the problem, the connected Android
device does not support
•
Switch off the developer options on the Android device.
•
Reconnect the Android device.
•
If this does not solve the problem, the connected Android
device does not support
, launch any media player application
, relaunch the current media player
( 7)
[BROWSE MODE]. ( 18)
[BROWSE MODE]. ( 18)
( 18)
SymptomRemedy
Playback is intermittent
or sound skips.
“ANDROID ERROR”/
ANDROID
“NADEVICE”
“ADDERROR”New station creation is unsuccessful.
“CHECKDEVICE”Check the Pandora application on your device.
“NOSKIPS”The skip limit has been reached.
“NOSTATIONS”No stations are found.
“STATIONLIMIT”The number of registered stations has reached its limit.
“CONNECT ERROR”Communication is unstable.
Pandora
“RATING ERROR”Registration of thumbs up/thumbs down has failed due to
“THUMBS N/A”Registration of thumbs up/thumbs down is not allowed.
“LICENSE ERROR”You try to access from a country which Pandora is not
iHeartRadio station
cannot be selected.
“CANNOT CREATE”Custom station name creation is unsuccessful.
“CANNOT SAVE”Addition to the favorite category failed.
“DISCONNECTED”Check the connection to the device.
“NOSKIPS”The skip limit has been reached. Retry later.
iHeartRadio
“NOSTATIONS”No stations are found.
“NOT CONNECTED”Link to the application is impossible.
“IHEARTLINK UP”Make sure you have installed the latest version of the iHeart
Turn off the power saving mode on the Android device.
•
Reconnect the Android device.
•
Restart the Android device.
Retry after deleting unnecessary stations from your device.
insufficient network connectivity.
deliverable.
If “Explicit Content” in [Account Settings] is checked in
the web version of iHeartRADIO, custom stations become
unavailable.
Link for KENWOOD application on your device.
TROUBLESHOOTING
REFERENCES
SymptomRemedy
“PLEASE LOGIN”You haven’t log in. Log in again.
“STATION NOT AVAILABLE” Broadcast from the station is over.
“STATION NOT SELECTED”No station is selected.
“STREAM ERROR”Broadcast data is interrupted.
iHeartRadio
“THUMB FAILED”Registration of Thumbs Up/Down has failed.
“TIMED OUT”The request has resulted in time-out.
Muting upon the reception of a phone call
Connect the MUTE wire to your telephone using a commercial telephone accessory.
When a call comes in, “CALL” appears.
•
To continue listening to the audio system during a call, press . “CALL” disappears
and the audio system resumes.
When the call ends, “CALL” disappears.
(The audio system pauses.)
(The audio system resumes.)
( 21)
Maintenance
Cleaning the unit
Wipe off dirt on the faceplate with a dry silicone or soft cloth.
Cleaning the connector
Detach the faceplate and clean the connector gently
with a cotton swab, being careful not to damage
the connector.
Handling discs
•
Do not touch the recording surface of the disc.
•
Do not stick tape etc. on the disc, or use a disc with tape stuck on it.
•
Do not use any accessories for the disc.
•
Clean from the center of the disc and move outward.
•
Clean the disc with a dry silicone or soft cloth. Do not use any solvents.
•
When removing discs from this unit, pull them out horizontally.
•
Remove burrs from the center hole and disc edge before inserting a disc.
More information
For: – Latest firmware updates and latest compatible item list
– Any other latest information
Visit <www.kenwood.com/cs/ce/>.
General
•
This unit can only play the following CDs:
•
For detailed information and notes about the playable audio files, visit
<www.kenwood.com/cs/ce/audiofile/>.
Connector (on the reverse
side of the faceplate)
ENGLISH
17
REFERENCES
Playable files
•
Playable audio file:
For disc: MP3 (.mp3), WMA (.wma)
For USB mass storage class device: MP3 (.mp3), WMA (.wma), WAV (.wav), FLAC (.flac)
•
Playable disc media: CD-R/CD-RW/CD-ROM
•
Playable disc file format: ISO 9660 Level 1/2, Joliet, Long file name
•
Playable USB device file system: FAT12, FAT16, FAT32
Even when audio files comply with the standards listed above, playback may be impossible
depending on the types or conditions of media or device.
Unplayable discs
•
Discs that are not round.
•
Discs with coloring on the recording surface or discs that are dirty.
•
Recordable/ReWritable discs that have not been finalized.
•
8cm CD. Attempting to insert using an adapter may cause malfunction.
About USB devices
•
You cannot connect a USB device via a USB hub.
•
Connecting a cable whose total length is longer than 5m may result in abnormal playback.
•
This unit cannot recognize a USB device whose rating is other than 5V and exceeds 1A.
About iPod/iPhone
Made for
–
iPod touch (2nd, 3rd, 4th, 5th, and 6th generation)
–
iPod classic
–
iPod nano (3rd, 4th, 5th, 6th, and 7th generation)