Kenwood KDC-255U Instruction Manual

Take the time to read through this instruction manual. Familiarity with installation and operation procedures will help you obtain the best performance from your new CD-receiver.
For your records
Record the serial number, found on the back of the unit, in the spaces designated on the warranty card, and in the space provided below. Refer to the model and serial numbers whenever you call upon your Kenwood dealer for information or service on the product. Model KDC-X397/ KDC-355U/ KDC-255U/ KDC-155U/ KDC-MP255U/ KDC-MP155U/ KMR-355U Serial number
US Residents Only
Register Online
GET0847-001A (KW/K0)© 2012 JVC KENWOOD Corporation
KDC-X397 KDC-355U KDC-255U KDC-155U
CD-RECEIVER
INSTRUCTION MANUAL
AMPLI-TUNER LECTEUR DE CD
MODE D’EMPLOI
REPRODUCTOR DE DISCOS COMPACTOS RECEPTOR DE FM/AM
MANUAL DE INSTRUCCIONES
KDC-MP255U KDC-MP155U KMR-355U
2
CONTENTS BEFORE USE
Warning
Do not operate any function that takes your attention away from safe driving.
Caution
Volume setting:
• Adjust the volume so that you can hear sounds outside the car to prevent accident.
• Lower the volume before playing digital sources to avoid damaging the speakers by the sudden increase of the output level.
General:
• Avoid using the USB device or iPod/iPhone if it might hinder driving safety.
• Make sure all important data has been backed up. We shall bear no responsibility for any loss of recorded data.
• Never put or leave any metallic objects (such as coins or metal tools) inside the unit, to prevent a short circuit.
If a disc error occurs due to condensation on the laser lens, eject the disc and wait for the moisture to evaporate.
Remote control (RC-406):
• Do not leave the remote control in hot places such as on the dashboard.
• The Lithium battery is in danger of explosion if replaced incorrectly. Replace it only with the same or equivalent type.
• The battery pack or batteries shall not be exposed to excessive heat such as sunshine, fire or the like.
• Keep battery out of reach of children and in original package until ready to use. Dispose of used batteries promptly. If swallowed, contact a physician immediately.
CALIFORNIA, USA ONLY This perchlorate WARNING applies only to the product sold or distributed in California USA “Perchlorate
Material–special handling may apply, See www.dtsc.ca.gov/hazardouswaste/perchlorate.”
BEFORE USE 2
BASICS 3
GETTING STARTED 4
RADIO 5
CD / USB / iPod 6
AUX 7
PANDORA®
(for
KDC-X397
/
KDC-355U
/
KDC-255U
/
KDC-155U
/
KMR-355U
) 8
SiriusXM™
(for
KDC-X397
/
KDC-355U
/
KMR-355U
) 8
AUDIO SETTINGS 10
DISPLAY SETTINGS 11
MORE INFORMATION 11
TROUBLESHOOTING 12
SPECIFICATIONS 13
INSTALLATION / CONNECTION 14
How to read this manual
• Operations explained mainly using buttons on the faceplate.
[XX]
indicates the selected items.
(« XX)
indicates references are available on
the stated page number.
Maintenance
Cleaning the unit: Wipe off dirt on the faceplate with a dry silicon or soft cloth.
Cleaning the connector: Detach the faceplate and clean the connector with a
cotton swab gently, being careful not to damage the connector.
Handling discs:
• Do not touch the recording surface of the disc.
• Do not stick tape etc. on the disc, or use a disc with tape stuck on it.
• Do not use any accessories for the disc.
• Clean from the center of the disc and move outward.
• Clean the disc with a dry silicon or soft cloth. Do not use any solvents.
• When removing discs from this unit, pull them out horizontally.
• Remove burrs from the center hole and disc edge before inserting a disc.
Connector (on the reverse side of the faceplate)
3
KDC-X397
KDC-MP155U
KDC-155U KMR-355U
KDC-X397 KDC-255UKDC-355U
KDC-MP255U
BASICS
To Do this (on the faceplate) Do this (on the remote control)
Turn on the power Press L SRC.
• Press and hold to turn off the power.*
1
Press and hold SRC to turn off the power. ( Pressing SRC does not turn on the power. )
Adjust the volume Turn the volume knob. Press VOL
or VOL .
Press ATT during playback to attenuate the sound.
• Press again to cancel.
Select a source Press L SRC repeatedly. Press SRC repeatedly.
Change the display information*
2
Press SCRL DISP repeatedly.
• Press and hold to scroll the current display information.
( not available )
*
1
For
KMR-355U
: The power will automatically turn off after 20 minutes when in standby mode (Auto Power Off).
*
2
For
KDC-MP255U
/
KDC-MP155U
: You can also select to turn off the display information by pressing SCRL DISP repeatedly.
Faceplate
How to reset
Attach
Detach
Remote control (RC-406)
(not supplied for
KMR-355U
)
Volume knob
(turn/press) Loading slot
Detach button
Display window
ENGLISH |
Pull out the insulation sheet when using for the first time.
Your preset adjustments will also be erased.
How to replace the battery
* Not used.
Remote sensor (Do not expose to bright sunlight.)
4
GETTING STARTED
Cancel the demonstration
When you turn on the power (or after you reset the unit), the display
shows: “CANCEL DEMO” \ “PRESS” \ “VOLUME KNOB”
1 Press the volume knob.
[YES]
is selected for the initial setup.
2 Press the volume knob again. “DEMO OFF” appears.
For
KMR-355U
,
[DEMO OFF]
is selected initially.
Set the clock
1 Press the volume knob to enter
[FUNCTION]
.
2 Turn the volume knob to select
[SETTINGS]
, then press the knob.
3 Turn the volume knob to select
[CLOCK]
, then press the knob.
4 Press the volume knob to select
[CLOCK ADJUST]/ [CLOCK ADJ]
.
5 Turn the volume knob to adjust the hour, then press the knob. 6 Turn the volume knob to adjust the minute, then press the knob. Press 4
/
¢ to move between the hour and minute adjustment.
7 Press and hold to exit.
(or)
Press and hold SCRL DISP to enter clock adjustment mode
directly while in clock display screen.
Then, perform steps 5 and 6 above to set the clock.
1
2
Set the initial settings
1 Press SRC to enter
[STANDBY]
.
2 Press the volume knob to enter
[FUNCTION]
.
3 Turn the volume knob to select
[INITIAL SET]
, then press the knob.
4 Turn the volume knob to make a selection (see the table below), then press
the knob.
5 Press and hold to exit.
• To return to the previous hierarchy, press
.
Default:
XX
PRESET TYPE NORMAL/ NORM: Memorizes one station for each preset button in each band (FM1/
FM2/ FM3/ AM). ; MIX: Memorizes one station or SiriusXM channel for each preset button regardless of the selected band or SiriusXM channel.
KEY BEEP
ON: Activates the keypress tone. ; OFF: Deactivates.
PANDORA SRC
(Except for
KDC-MP255U
/
KDC-MP155U
)
ON: Enables PANDORA in source selection. ; OFF: Disables. (
«
8)
BUILT-IN AUX/ BUILTIN AUX
ON: Enables AUX in source selection. ; OFF: Disables. (« 7)
CD READ
1: Automatically distinguishes between audio file disc and music CD. ; 2: Forces to play
as a music CD. No sound can be heard if an audio file disc is played.
SWITCH PRE
(Except for
KDC-X397/ KDC-355U
) REAR/ SUB-W: Selects whether rear speakers or a subwoofer are connected to the line out terminals on the rear (through an external amplifier).
SP SELECT
OFF/ 5/4/ 6 × 9/6/ OEM: Selects according to the speaker size (5 inches or
4 inches, 6×9 inches or 6 inches) or OEM speakers for optimum performance.
F/W UPDATE
F/W UP xx.xx
YES: Starts upgrading the firmware. ; NO: Cancels (upgrading is not activated).
For details on how to update the firmware, see: www.kenwood.com/cs/ce/
3
5
ENGLISH |
RADIO
Search for a station
1 Press L SRC to select TUNER. 2 Press repeatedly (or press
*
AM– / #FM+ on RC-406) to select FM1/
FM2/ FM3/ AM.
3 Press 4 / ¢ to search for a station.
To store a station: Press and hold one of the number buttons (1 to 6).
To select a stored station: Press one of the number buttons (1 to 6)
Direct Access Tuning (using RC-406) (except for
KMR-355U
)
1 Press
*
AM– / #FM+ to select a band.
2 Press DIRECT to enter Direct Access Tuning. “– – – • –” (for FM) or “– – – –” (for AM) appears on the display. 3 Press the number buttons to enter a frequency. 4 Press 4 / ¢ (+) to search for a frequency.
• To cancel, press
.
• If no operation is done for 10 seconds after step 3, Direct Access Tuning is automatically canceled.
Other settings
1 Press the volume knob to enter
[FUNCTION]
.
2 Turn the volume knob to select
[SETTINGS]
, then press the knob.
3 Turn the volume knob to make a selection (see the table on the right),
then press the knob.
4 Press and hold to exit.
Default:
XX
SEEK MODE Selects the tuning method for the
4
/ ¢ buttons.
AUTO1: Automatically searches for a station. ; AUTO2: Searches for a preset station. ; MANUAL: Manually search for a station.
AUTO MEMORY
YES: Automatically starts memorizing 6 stations with good reception. ; NO: Cancels. (Selectable only if [NORMAL] / [NORM] is selected for [PRESET TYPE].) (
«
4)
MONO SET
ON: Improves the FM reception, but the stereo effect may be lost. ; OFF: Cancels.
For
KDC-MP255U
/
KDC-MP155U
:
PTY SEARCH Selects the available Program Type (see below), then, press
4 / ¢
to start.
TI
ON: Allows the unit to temporarily switch to Traffic Information. ; OFF: Cancels.
CLOCK
TIME SYNC
ON: Synchronizes the unit’s time to the Radio Broadcast Data System station time. ; OFF: Cancels.
TUNER SET: Selectable only when the source is not TUNER.
TI
ON: Allows the unit to temporarily switch to Traffic Information. ; OFF: Cancels.
[MONO SET]/ [PTY SEARCH]/ [TI]
is selectable only when the source is FM.
• Available Program Type:
SPEECH: NEWS, INFORM
(information),
SPORTS, TALK, LANGUAGE, REL TALK
(religious talk),
PERSNLTY
(personality),
PUBLIC, COLLEGE, HABL ESP
(spanish talk),
MUSC ESP
(spanish music),
HIP HOP, WEATHER
MUSIC
:
ROCK, CLS ROCK
(classic rock),
ADLT HIT
(adult hits),
SOFT RCK
(softrock),
TOP 40,
COUNTRY
,
OLDIES, SOFT, NOSTALGA
(nostalgia),
JAZZ, CLASSICL
(classical),
R & B
(rhythm and blues),
SOFT R&B
(soft rhythm and blues),
REL MUSC
(religious
music)
The unit will search for the Program Type categorized under
[SPEECH]
or
[MUSIC]
if
selected.
• For
KDC-MP255U
/
KDC-MP155U
: If the volume is adjusted during reception of traffic information or alarm, the adjusted volume is memorized automatically. It will be applied the next time traffic information or alarm function is turned on.
6
CD / USB / iPod
To Do this CD USB iPod
Pause or resume playback
Press 6 38 (or ENT 38 on RC-406).
Select a track/file Press 4 / ¢ (or 4 / ¢ (+) on RC-406).
Select a folder
Press 1 – / 2 + (or
*
AM– / #FM+ on RC-406).
*
2
Reverse/Fast-forward Press and hold 4 / ¢ (or 4 / ¢ (+) on RC-406).
Select a track/file from a list
1 Press . 2 Turn the volume knob to make a selection, then press the knob.
• MP3/WMA file: Select the desired folder, then a file.
• iPod or KENWOOD Music Editor Light (KME Light)/ KENWOOD Music Control (KMC) file
*
4
: Select the desired file from the list (PLAYLISTS, ARTISTS,
ALBUMS, SONGS, PODCASTS
*
5
, GENRES, COMPOSERS
*
5
).
• To return to the root folder (or first file), press number button 5.
• To return to the previous hierarchy, press
.
• To cancel, press and hold
.
*
3
• To skip songs at a specific ratio, press 4 / ¢. («
7)
*4*
3
Repeat play Press 4
repeatedly.
• Audio CD: TRACK/ TRAC REPEAT, REPEAT OFF
• MP3/WMA file: FILE REPEAT, FOLDER/ FOLD REPEAT, REPEAT OFF
• iPod or KME Light/ KMC file: FILE REPEAT, REPEAT OFF
*
3
Random play Press 3
or
repeatedly.
• Audio CD: DISC RANDOM, RANDOM OFF
• MP3/WMA/iPod or KME Light/ KMC file: FOLDER/ FOLD RANDOM, RANDOM OFF
*
3
Press and hold 3
or
to select “ALL RANDOM.”
*
2
*
3
*
2
Only for MP3/WMA files.
*
3
Applicable only when
[MODE OFF]
is selected.
Start playback
CD
The source changes to CD and playback starts.
USB
The source changes to USB and playback starts.
iPod/iPhone (except for
KDC-MP155U
)
The source changes to iPod and playback starts.
Press and hold iPod to select the control mode while in iPod source.
MODE ON:
From the iPod
*
1
.
MODE OFF:
From the unit.
*
1
You can still control play/pause, file
selection, fast-forward or reverse files from the unit.
Label side
0
: Eject disc
USB input terminal
USB input terminal
CA-U1EX (max.: 500 mA) (optional accessory)
KCA-iP102 (optional accessory)
: Applicable
— : Not applicable
KDC-MP155U
*
4
Only for files registered in the database created with
KME Light/ KMC.
(« 11)
*
5
Only for iPod.
Loading...
+ 12 hidden pages