Kenwood KDC-202 User Manual

KDC-2022 KDC-2022V KDC-202MR KDC-222

CD-RECEIVER

INSTRUCTION MANUAL

AMPLI-TUNER-LECTEUR DE CD

MODE D’EMPLOI

REPRODUCTOR DE DISCOS COMPACTOS RECEPTOR DE FM/AM

MANUAL DE INSTRUCCIONES

RECEPTOR DE CD

MANUAL DE INSTRUÇÕES

KDC-222S KDC-122 KDC-122S

Take the time to read through this instruction manual. Familiarity with installation and operation procedures will help you obtain the best performance from your new CD-receiver.

For your records

Record the serial number, found on the back of the unit, in the spaces designated on the warranty card, and in the space provided below. Refer to the model and serial numbers whenever you call upon your KENWOOD dealer for information or service on the product. Model KDC-2022, KDC-2022V, KDC-202MR, KDC-222, KDC-222S,

KDC-122, KDC-122S Serial number

Contents

Safety precautions......................3

About CDs...................................5

English

General features .........................6

Power Selecting the Source Volume Attenuator Loudness System Q Audio Control Speaker Setting Clock Display Adjusting Clock DSI (Disabled System Indicator) Theft Deterrent Faceplate

Tuner features .............................9

Tuning Mode Tuning Station Preset Memory Auto Memory Entry Preset Tuning CRSC (Clean Reception System Circuit)

CD/External disc control

features ..................................11

Playing CD Playing External Disc Fast Forwarding and Reversing Track Search Album Search Track/Album Repeat Track Scan Random Play Magazine Random Play Direct Track Search Direct Album Search

Basic Operations of remote......14

Loading and Replacing the battery Basic operations In Tuner source In Disc source

Accessories ...............................16

Installation Procedure ..............16

Connecting Wires to Terminals 17

Installation ................................18

Troubleshooting Guide .............20

Specifications ...........................23

Warning .....................................24

— 2 —

Safety precautions

2WARNING

To prevent injury or fire, take the following precautions:

• Insert the unit all the way in until it is fully locked in place. Otherwise it may fall out of place when jolted.

• When extending the ignition, battery, or ground wires, make sure to use automotivegrade wires or other wires with a 0.75mm (AWG18) or more to prevent wire deterioration and damage to the wire coating.

•To prevent a short circuit, never put or leave any metallic objects (such as coins or metal tools) inside the unit.

• If the unit starts to emit smoke or strange smells, turn off the power immediately and consult your Kenwood dealer.

• Make sure not to get your fingers caught between the faceplate and the unit.

• Be careful not to drop the unit or subject it to strong shock. The unit may break or crack because it contains glass parts.

• Do not touch the liquid crystal fluid if the LCD is damaged or broken due to shock. The liquid crystal fluid may be dangerous to your health or even fatal. If the liquid crystal fluid from the LCD contacts your body or clothing, wash it off with soap immediately.

2CAUTION

To prevent damage to the machine, take the following precautions:

• Make sure to ground the unit to a negative 12V DC power supply.

• Do not open the top or bottom covers of the unit.

• Do not install the unit in a spot exposed to direct sunlight or excessive heat or humidity. Also avoid places with too much dust or the possibility of water splashing.

• Do not set the removed faceplate or the faceplate case in areas exposed to direct sunlight, excessive heat or humidity. Also avoid places with too much dust or the possibility of water splashing.

•To prevent deterioration, do not touch the terminals of the unit or faceplate with your fingers.

• Do not subject the faceplate to excessive shock, as it is a piece of precision equipment.

• When replacing a fuse, only use a new one with the prescribed rating. Using a fuse with the wrong rating may cause your unit to malfunction.

•To prevent a short circuit when replacing a fuse, first disconnect the wiring harness.

• Do not place any object between the faceplate and the unit.

• Do not use your own screws. Use only the screws provided. If you use the wrong screws, you could damage the unit.

IMPORTANT INFORMATION About CD players/disc changers

connected to this unit

KENWOOD disc changers/ CD players released in 1998 or later can be connected to this unit. Refer to the catalog or consult your Kenwood dealer for connectable models of disc changers/ CD players. Note that any KENWOOD disc changers/ CD players released in 1997 or earlier and disc changers made by other makers cannot be connected to this unit. Unsupported connection may result in damage. Setting the "O-N" Switch to the "N" position for the applicable KENWOOD disc changers/ CD players. The functions that can be used and the information that can be displayed will differ depending on the models being connected.

You can damage both your unit and the CD changer if you connect them incorrectly.

Do Not Load 3-in. CDs in the CD slot

If you try to load a 3 in. CD with its adapter into the unit, the adapter might separate from the CD and damage the unit.

— 3 —

Safety precautions

NOTE

• If you experience problems during installation, consult your Kenwood dealer.

English

• If the unit does not seem to be working right, try pressing the reset button first. If that does not solve the problem, consult your Kenwood dealer.

•Press the reset button if the Disc auto changer fails to operate correctly. Normal operatin should be restored.

Reset button

• Characters in the LCD may become difficult to read in temperatures below 41 ˚F (5 ˚C).

• The illustrations of the display and the panel appearing in this manual are examples used to explain more clearly how the controls are used. Therefore, what appears on the display in the illustrations may differ from what appears on the display on the actual equipment, and some of the illustrations on the display may represent something impossible in actual operation.

Cleaning the Faceplate Terminals

If the terminals on the unit or faceplate get dirty, wipe them with a dry, soft cloth.

Cleaning the Unit

If the faceplate of this unit is stained, wipe it with a dry soft cloth such as a silicon cloth. If the faceplate is stained badly, wipe the stain off with a cloth moistened with neutral cleaner, then wipe neutral detergent off.

Applying spray cleaner directly to the unit may affect its mechanical parts. Wiping the faceplate with a hard cloth or using a volatile liquid such as thinner or alcohol may scratch the surface or erases characters.

Cleaning the CD Slot

As dust tends to accumulate in the CD slot, clean it every once in a while. Your CDs can get scratched if you put them in a dusty CD slot.

Lens Fogging

Right after you turn on the car heater in cold weather, dew or condensation may form on the lens in the CD player of the unit. Called lens fogging, CDs may be impossible to play. In such a situation, remove the disc and wait for the condensation to evaporate. If the unit still does not operate normally after a while, consult your Kenwood dealer.

— 4 —

About CDs

Handling CDs

• Don’t touch the recording surface of the CD.

• CD-R and CD-RW are easier to damage than a normal music CD. Use a CD-R or a CD-RW after reading the caution items on the package etc.

• Don’t stick tape etc. on the CD. Also, don’t use a CD with tape stuck on it.

When using a new CD

If the CD center hole or outside rim has burrs, use it after removing them with a ball pen etc.

Burrs

CD cleaning

Clean from the center of the disc and move outward.

Removing CDs

When removing CDs from this unit pull them out horizontally.

CDs that can’t be used

• CDs that aren’t round can’t be used.

• CDs with coloring on the recording surface or that are dirty can’t be used.

• This unit can only play the CDs with

It may not correctly play discs which do not have the mark.

•A CD-R or CD-RW that hasn’t been finalized can’t be played. (For the finalization process refer to your CD-R/CD-RW writing software, and your CD-R/CD-RW recorder instruction manual.)

CD storage

• Don’t place them in direct sunlight (On the seat or dashboard etc.) and where the temperature is high.

• Store CDs in their cases.

CD accessories

Don’t use disc type accessories.

— 5 —

General features

AM FM

Q/CLK/

AUDADJ

ATT/

LOUD

SRC #1 #3

¢4ud

Release button

(KDC-2022/KDC-2022V/KDC-202MR/ KDC-222/KDC-222S only)

English

KDC-2022/KDC-2022V/KDC-202MR

SYSTEM Q indicator

KDC-222/KDC-222S/KDC-122/KDC-122S

SYSTEM Q indicator

ATT indicator

Clock indicator

ATT indicator

LOUD indicator

Clock display

Clock indicator

Power

Turning ON the Power

Press the [SRC] button.

Turning OFF the Power

Press the [SRC] button for at least 1 second.

Selecting the Source

Press the [SRC] button.

Source required Display

Tuner "TUnE" CD "CD" External disc "DISC"

(Function of the KDC-2022/KDC-2022V/KDC-202MR) Standby (Illumination only mode) "OFF"

Volume

Increasing Volume

Press the [u] button.

Decreasing Volume

Press the [d] button.

Attenuator

Turning the volume down quickly.

Press the [ATT] button.

Each time the button is pressed the Attenuator turns ON or OFF. When it’s ON, the "ATT" indicator blinks.

— 6 —

Loudness

Compensating for low and high tones during low volume.

Press the [LOUD] button for at least 1 second.

Each time the button is pressed for at least 1 second the Loudness turns ON or OFF. When it’s ON, "LOUD" indicator is ON.

System Q

You can recall the best sound setting preset for different types of the music.

1 Select the source to set

Press the [SRC] button.

2 Select the Sound type

Press the [Q] button.

Each time the button is pressed the sound setting switches.

Sound setting Display

Flat "SQ-1" Rock "SQ-2" Top 40 "SQ-3" Pops "SQ-4" Jazz "SQ-5" Easy "SQ-6"

• Each setting value is changed with the <Speaker setting> (page

8). First, select the speaker type with the Speaker setting.

• When the System Q setting is changed, the Bass, Middle, and Treble set in audio control replace the System Q values.

Audio Control

1 Select the source for adjustment

Press the [SRC] button.

2 Enter Audio Control mode

Press the [AUD] button for at least 1 second.

3 Select the Audio item for adjustment

Press the [FM] or [AM] button.

Each time the button is pressed the items that can be adjusted switch as shown below.

4 Adjust the Audio item

Press the [4] or [¢] button.

Adjustment Item Display Range

Bass level "BAS" –8 — +8 Middle level "MID" –8 — +8 Treble level "TRE" –8 — +8 Balance "BL" Left 15 — Right 15 Fader "FD" Rear 15 — Front 15

5 Exit Audio Control mode

Press the [AUD] button.

— 7 —

General features

Speaker Setting

Fine-tuning so that the System Q value is optimal when setting the speaker type.

English

1 Enter Standby

Press the [SRC] button.

Select the "OFF" display.

2 Enter Speaker Setting mode

Press the [Q] button.

3 Select the Speaker type

Press the [4] or [¢] button.

Each time the button is pressed the setting switches as shown below.

Speaker type Display

OFF "SP-F" For the OEM speaker "SP-O" For 6 & 6x9 in. speaker "SP-6" For 5 & 4 in. speaker "SP-5"

4 Exit Speaker Setting mode

Press the [Q] button.

Clock Display

Press the [CLK] button.

Each time the button is pressed the clock display turns ON or OFF. When it’s ON, the clock indicator is ON.

Adjusting Clock

1 Select the clock display

Press the [CLK] button.

2 Enter clock adjustment mode

Press the [CLK] button for at least 2 seconds.

The clock display blinks.

3 Adjust the hours

Press the [FM] or [AM] button.

Adjust the minutes

Press the [4] or [¢] button.

4 Exit clock adjustment mode

Press the [CLK] button.

Function of the KDC-2022/KDC-2022V/KDC-202MR/KDC-222/KDC-222S

DSI (Disabled System Indicator)

A red indicator will blink on the unit after the faceplate is removed, warning potential thieves.

1 Turn the power OFF

Press the [SRC] button for at least 1 second.

2 Set the DSI

While pressing the [#1] and [#3] button, press the [SRC] button.

Each time the step 1 and 2 operation is done the DSI turns ON or OFF.

— 8 —

Function of the KDC-2022/KDC-2022V/KDC-202MR/KDC-222/KDC-222S

CRSC

FM/

AUTO /

AME

#1 - 6SRC

¢4

Theft Deterrent Faceplate

The faceplate of the unit can be detached and taken with you, helping to deter theft.

Removing the Faceplate

Press the Release button.

The faceplate is unlocked, allowing you to detach it.

• The faceplate is a precision piece of equipment and can be damaged by shocks or jolts. For that reason, keep the faceplate in its special storage case while detached.

• Do not expose the faceplate or its storage case to direct sunlight or excessive heat or humidity. Also avoid places with too much dust or the possibility of water splashing.

Reattaching the Faceplate

1 Align the projections on the unit with the grooves on the

faceplate.

Tuner features

KDC-2022/KDC-2022V/KDC-202MR

ST indicator

Preset station number

CRSC indicator

2 Push the faceplate in until it clicks.

The faceplate is locked in place, allowing you to use the unit.

Band display

KDC-222/KDC-222S/KDC-122/KDC-122S

Band display

— 9 —

Preset station number

ST indicator

AUTO indicator

Frequency display

CRSC indicator

AUTO indicator

Frequency display

Tuner features

Tuning Mode

Choose the tuning mode.

English

Press the [AUTO] button.

Each time the button is pressed the Tuning mode switches as shown below.

Tuning mode Display Operation

Auto seek "AUTO 1" Automatic search for a station.

Preset station "AUTO 2" Search in order of the stations seek indicator in the Preset memory.

Manual — Normal manual tuning control.

Tuning

Selecting the station.

1 Select tuner source

Press the [SRC] button.

Select the "TUnE" display.

2 Select the band

Press the [FM] or [AM] button.

Each time the [FM] button is pressed it switches between the FM1, FM2, and FM3 bands.

3 Tune up or down band

Press the [4] or [¢] button.

During reception of stereo stations the "ST" indicator is ON.

Station Preset Memory

Putting the station in the memory.

indicator

1 Select the band

Press the [FM] or [AM] button.

2 Select the frequency to put in the memory

Press the [4] or [¢] button.

3 Put the frequency in the memory

Press the [#1] — [#6] button for at least 2 seconds.

The preset number display blinks 1 time. On each band, 1 station can be put in the memory on each [#1] — [#6] button.

Auto Memory Entry

Putting stations with good reception in the memory automatically.

1 Select the band for Auto Memory Entry

Press the [FM] or [AM] button.

2 Open Auto Memory Entry

Press the [AME] button for at least 2 seconds.

When 6 stations that can be received are put in the memory Auto Memory Entry closes.

Preset Tuning

Calling up the stations in the memory.

1 Select the band

Press the [FM] or [AM] button.

2 Call up the station

Press the [#1] — [#6] button.

— 10 —

CRSC (Clean Reception System Circuit)

DISC- DISC+

REP

RDM

SCAN

M.RDMSRC

¢40

Temporarily have reception switched from stereo to mono to reduce multi-path noise when listening to the FM station.

Press the [CRSC] button for at least 1 second.

Each time the button is pressed CRSC turns ON or OFF. When it's ON, the CRSC indicator is ON.

CD/External disc control features

KDC-2022/KDC-2022V/KDC-202MR

Disc number

Track number

Track time

IN indicator

KDC-222/KDC-222S/KDC-122/KDC-122S

IN indicator

Track time

— 11 —

SCN indicator

RDM indicator

Track number

RDM indicator

REP indicator

CD/External disc control features

Playing CD

When a CD is inserted

English

Press the [SRC] button.

Select the "CD" display.

When a CD is inserted, the "IN" indicator is ON.

Eject the CD

Press the [0] button.

3 in. (8cm) CD cannot be played. Using an adapter and inserting them into this unit can cause damage.

Function of the KDC-2022/KDC-2022V/KDC-202MR

Playing External Disc

Playing discs set in the optional accessory disc player connected to this unit.

Press the [SRC] button.

Select the display for the disc player you want.

Display examples:

Display Disc player

"CD-2" CD player "DISC" CD changer "DISC" MD changer

• Disc #10 is displayed as "0".

• The functions that can be used and the information that can be displayed will differ depending on the external disc players being connected.

Fast Forwarding and Reversing

Fast Forwarding

Hold down on the [¢] button.

Release your finger to play the disc at that point.

Reversing

Hold down on the [4] button.

Release your finger to play the disc at that point.

Track Search

Selecting the song you want to hear.

Press the [4] or [¢] button.

Function of the KDC-2022/KDC-2022V/KDC-202MR

Album Search (Function of disc changer)

Selecting the disc you want to hear.

Press the [DISC–] or [DISC+] button.

Track/Album Repeat

Replaying the song/disc you're listening to.

Press the [REP] button.

Each time the button is pressed the Repeat Play switches as shown below.

Repeat play Display

Track Repeat "REP" indicator & Track No. blink. Album Repeat "REP" indicator & Disc No. blink.

(Function of disc changer) OFF —

— 12 —

Track Scan

Playing the first part of each song on the disc you are listening to and searching for the song you want to listen to.

1 Start Track Scan

Press the [SCAN] button.

"SCN" indicator is ON.

2 Release it when the song you want to listen to is played

Press the [SCAN] button.

Random Play

Playing all the songs on the disc in random order.

Press the [RDM] button.

Each time the button is pressed Random Play turns ON or OFF. When it's ON, the "RDM" indicator is ON and the track number blinks.

When the [¢] button is pressed, the next song select starts.

When it's ON, the "RDM" indicator is ON and the track and disc number blink.

When the [¢] button is pressed, the next song select starts.

Function of the KDC-2022/KDC-2022V

Direct Track Search (Function of remote)

Doing Track Search by entering the track number.

1 Enter the track number

Press the number buttons on the remote.

2 Do Track Search

Press the [4] or [¢] button.

Canceling Direct Track Search

Press the [38] button.

Function of the KDC-2022/KDC-2022V

Direct Album Search

(Function of disc changers with remote)

Doing Disc Search by entering the disc number.

Function of the KDC-2022/KDC-2022V/KDC-202MR

Magazine Random Play

(Function of disc changer)

Play the songs on all the discs in the disc changer in random order.

Press the [M.RDM] button.

Each time the button is pressed the Magazine Random Play turns ON or OFF.

1 Enter the disc number

Press the number buttons on the remote.

2 Do Album Search

Press the [DISC+] or [DISC–] button.

Canceling Direct Album Search

Press the [38] button.

Input "0" to select disc 10.

— 13 —

[#0] — [#9]

FM/AM/DISC

/DISC–

ATT

4/¢

VOL.

SRC

Basic Operations of remote

Accessory of the KDC-2022/KDC-2022V

English

Loading and Replacing the battery

Use one lithium battery (CR2025). Insert the batteries with the + and – poles aligned properly, following the illustration inside the case.

Not used

2WARNING

Store unused batteries out of the reach of children. Contact a doctor immediately if the battery is accidentally swallowed.

Do not set the remote on hot places such as above the dashboard.

Basic operations

[VOL.] buttons

Adjusting the volume.

[SRC] button

Each time the button is pressed the source switches. For the source switching order refer to <Selecting the Source> (page 6).

[ATT] button

Turning the volume down quickly. When it is pressed again it returns to the previous level.

— 14 —

In Tuner source

[FM]/ [AM] buttons

Select the band. Each time the [FM] button is pressed it switches between the FM1, FM2, and FM3 bands.

[4]/ [¢] buttons

Tune up or down band.

[#0] — [#9] buttons

Press buttons [#1] — [#6] to recall preset stations.

In Disc source

[4]/ [¢] buttons

Doing track forward and backward.

[DISC+]/ [DISC–] buttons

Doing album forward and backward.

[38] button

Each time the button is pressed the song pauses and plays.

[#0] — [#9] buttons

When in <Direct Track Search> (page 13) and <Direct Album Search> (page 13), enter the track/disc number.

— 15 —

Accessories

External view

English

......... Number of items

.........1

.........2

The use of any accessories except for those provided might result in damage to the unit. Make sure only to use the accessories shipped with the unit, as shown above.

External view

......... Number of items

(KDC-2022/KDC-2022V/ KDC-222/KDC-222S only)

Installation Procedure

1. To prevent a short circuit, remove the key from the ignition and

disconnect the - battery.

2. Make the proper input and output wire connections for each unit.

3. Connect the speaker wires of the wiring harness.

4. Connect the wiring harness wires in the following order: ground, battery, ignition.

5. Connect the wiring harness connector to the unit.

6. Install the unit in your car.

7. Reconnect the - battery.

8. Press the reset button.

.........4

.........1

2WARNING

If you connect the ignition wire (red) and the battery wire (yellow) to the car chassis (ground), you may cause a short circuit, that in turn may start a fire. Always connect those wires to the power source running through the fuse box.

2CAUTION

• If your car's ignition does not have an ACC position, connect the ignition wires to a power source that can be turned on and off with the ignition key. If you connect the ignition wire to a power source with a constant voltage supply, as with battery wires, the battery may die.

• If the console has a lid, make sure to install the unit so that the faceplate will not hit the lid when closing and opening.

• If the fuse blows, first make sure the wires aren’t touching to cause a short circuit, then replace the old fuse with one with the same rating.

• Insulate unconnected wires with vinyl tape or other similar material. To prevent a short circuit, do not remove the caps on the ends of the unconnected wires or the terminals.

• Connect the speaker wires correctly to the terminals to which they correspond. The unit may be damaged or fail to work if you share the - wires or ground them to any metal part in the car.

• When only two speakers are being connected to the system, connect the connectors either to both the front output terminals or to both the rear output terminals (do not mix front and rear). For example, if you connect the + connector of the left speaker to a front output terminal, do not connect the - connector to a rear output terminal

• After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. on the car are working properly.

•Mount the unit so that the mounting angle is 30° or less.

— 16 —

P.CONT

ANT. CONT.

FRONT • L

FRONT • R

REAR • L

REAR • R

–

REAR

Connecting Wires to Terminals

Front left output (White) (KDC-2022/2022V/202MR only) 26

2 KENWOOD disc changer control input (KDC-2022/2022V/202MR only)

If no connections are made, do not let the wire come out from the tab.

6 Connect either to the power control terminal

when using the optional power amplifier, or to

the antenna control terminal in the vehicle.

Not Used 19

Do not let the wire come out from the tab. 4b

Ignition key switch

Car fuse box (Main fuse)

Car fuse box 14

Front right output (Red) (KDC-2022/2022V/202MR only) 27

To connect the Disc changer, consult your Disc changer manual. 3

Fuse (10A) 24

Wiring harness (Accessory1)25

Power control/Motor antenna control wire (Blue/White)

ACC 13

Ignition wire (Red) 20

Battery wire (Yellow) 21

Ground wire (Black) · (To car chassis) 22

White/Black

White

Gray/Black

Gray

Green/Black

Green

Purple/Black

Purple

Rear left output (White) 23

Rear right output (Red) 28

FM/AM antenna input 1

To front left speaker 30

To front right speaker 33

To rear left speaker 36

To rear right speaker 39

Battery 12

— 17 —

8 mm MAX.

ø5mm

8mm MAX.

Installation

■ Installation

■ Installing in Japanese-Made Cars

English

Screw (M4X8) (commercially available)

Self-tapping screw (commercially available)

Firewall or metal support

Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place.

Metal mounting strap (commercially available)

Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction (for example, the sound may skip).

1 Refer to the section "Removing the hard rubber frame" (page 19)

and then remove the hard rubber frame.

2 Align the holes in the unit (two locations on each side) with the

vehicle mounting bracket and secure the unit with the accessory screws.

T: Toyota cars N: Nissan cars

• During installation, do not use any screws except for those provided. The use of different screws might result in damage to the main unit.

• Damage may occur if a screwdriver or similar tool is used with excessive force during the installations.

■ Screwing the Faceplate on the Unit (KDC-2022/KDC-2022V/KDC-222/KDC-222S only)

If you want to fasten the faceplate to the main unit so that it does not fall off, screw in the provided screw (ø4 X 16 mm) in the hole shown below.

Never insert the taptite screw (ø4 × 16 mm) in any other screw hole than the one specified. If you screw it in another hole, it will contact and may cause damage to the mechanical parts inside the unit.

— 18 —

T/N

Accessory3...for Nissan car Accessory4 ...for Toyota car

Accessory5

■ Removing the hard rubber frame

1 Engage the catch pins on the removal tool and remove the two

locks on the lower level. Lower the frame and pull it forward as shown in the figure.

Lock

Catch

■ Removing the Unit

1 Refer to the section “Removing the hard rubber frame” and then

remove the hard rubber frame.

2 Remove the screw (M4 × 8) on the back panel. 3 Insert the two removal tools deeply into the slots on each side,

as shown.

Accessory2 Removal tool

2 When the lower level is removed, remove the upper two

locations.

The frame can be removed from the top side in the same manner.

Screw (M4X8) (commercially available)

4 Lower the removal tool

toward the bottom, and pull out the unit halfway while pressing towards the inside.

Be careful to avoid injury from the catch pins on the removal tool.

5 Pull the unit all the way out

with your hands, being careful not to drop it.

— 19 —

Accessory2 Removal tool

Troubleshooting Guide

What might seem to be a malfunction in your unit may just be the result of slight misoperation or miswiring. Before calling service, first check the following table for possible problems.

English

General

? The power does not turn ON.01

✔ The fuse has blown.

☞ After checking for short circuits in the wires, replace the fuse with

one with the same rating.

✔ No ACC position on vehicle ignition.02

☞ Connect the same wire to the ignition as the battery wire.

? Nothing happens when the buttons are pressed.04

✔ The computer chip in the unit is not functioning normally.

☞ Press the reset button on the unit (page 4).

? There’s a source you can’t switch.06

✔ There’s no CD inserted.

☞ Set the media you want to listen to. If there’s no media in this

unit, you can't swhich to each source.

? The memory is erased when the ignition is turned OFF.10

✔ The battery wire has not been connected to the proper terminal.

☞ Connect the wire correctly, referring to the section on

<Connecting Wires to Terminals>.

✔ The ignition and battery wire are incorrectly connected.11

☞ Connect the wire correctly, referring to the section on

<Connecting Wires to Terminals>.

? Even if Loudness is turned ON, high-pitched tone isn't compensated

for. 17

✔ Tuner source is selected.

☞ High-pitched tone isn't compensated for when in Tuner source.

? No sound can be heard, or the volume is low.

✔ The fader or balance settings are set all the way to one side.21

☞ Center the fader and balance settings.

✔ The input/output wires or wiring harness are connected incorrectly.22

☞ Reconnect the input/output wires or the wiring harness correctly.

See the section on <Connecting Wires to Terminals>.

? The sound quality is poor or distorted.25

✔ One of the speaker wires is being pinched by a screw in the car.

☞ Check the speaker wiring.

✔ The speakers are not wired correctly.27

☞ Reconnect the speaker wires so that each output terminal is

connected to a different speaker.

? The Touch Sensor Tone doesn’t sound.34

✔ The preout jack is being used.

☞ The Touch Sensor Tone can’t be output from the preout jack.

Tuner source

? Radio reception is poor.39

✔ The car antenna is not extended.

☞ Pull the antenna out all the way.

✔ The antenna control wire is not connected.40

☞ Connect the wire correctly, referring to the section on

<Connecting Wires to Terminals>.

— 20 —

Disc source

? "AVin" is displayed without achieving External disc control mode.50

✔ Unsupported disc changer is connected.51

☞ Use the disc changer mentioned in the IMPORTANT

INFORMATION of the section on <Safety precautions>(page 3).

? The specified disc does not play, but another one plays instead.52

✔ The specified CD is quite dirty.

☞ Clean the CD.

✔ The CD is upside-down.53

☞ Load the CD with the labeled side up.

✔ The disc is loaded in a different slot from that specified.54

☞ Eject the disc magazine and check the number for the specified

disc.

✔ The disc is severely scratched.55

☞ Tr y another disc instead.

? The specified track will not play.58

✔ Random play or magazine random play has been selected.

☞ Tu rn off random play or magazine random play.

? Track repeat, disc repeat, track scan, random play, and magazine

random play start by themselves.59

✔ The setting is not canceled.

☞ The settings for these functions remain on until the setting to off

or the disc ejected, even if the power is turned off or the source changed.

? Cannot play CD-R or CD-RW.60

✔ Finalization processing is not being conducted for CD-R/CD-RW.

☞ Conduct finalization processing with CD recorder.

✔ A non-compatible CD changer is being used to play the CD-R/CD-

RW.61 ☞ Use a CD changer compatible with CD-R/CD-RW to play.

? A CD ejects as soon as it is loaded.62

✔ The CD is upside-down.

☞ Load the CD with the labeled side up.

✔ The CD is quite dirty.63

☞ Clean the CD, referring to the section on <CD cleaning> (page 5).

? Can’t remove disc.64

✔ The cause is that more than 10 minutes has elapsed since the vehicle

ACC switch was turned OFF. ☞ The disc can only be removed within 10 minutes of the ACC

switch being turned OFF. If more than 10 minutes has elapsed, turn the ACC switch ON again and press the Eject button.

? The disc won’t insert.65

✔ There’s already another disc inserted.

☞ Press the [0] button and remove the disc.

? Direct Track Search and Direct Album Search can’t be done.66-1

✔ Another function is ON.

☞ Tu rn Random Play or other functions OFF.

? Track Search can't be done.66-2

✔ For the albums first or last song.

☞ For each album, Track Search can't be done in the backward

direction for the first song or in the forward direction for the last song.

If the following situations, consult your nearest service center:

• Even though the disc changer is connected, the Disc Changer source is

not ON, with "AVin" showing in the display during the Changer Mode.

• Even though no device (KCA-S210A, CA-C1AX, KDC-CPS89, KDC-CPS87,

KDC-CX87, KDC-CPS85, KDC-CX85, KDC-CPS82 or KDC-CX82) is connected, the Auxiliary input is entered when switching modes.

— 21 —

Troubleshooting Guide

The messages shown below display your systems condition.

E-01: No disc magazine has been loaded in the changer.

English

E-02: No disc has been loaded in the disc magazine.

E-04: No disc has been loaded in the disc magazine.

E-10: Nothing has been recorded on the MD.

E-11: No tracks are recorded on the MD, although it has a

E-12: The faceplate of the slave unit being connected to

E-77: The unit is malfunctioning for some reason.

E-99: The unit is malfunctioning for some reason.

The disc magazine is not completely loaded.E01

➪

Load the disc magazine properly.

No CD in the unit.

➪ Insert the CD.

➪

Load a disc into the disc magazine.

➪

Load a disc into the disc magazine. The CD is quite dirty. The CD is upside-down. The CD is scratched a lot.

➪ Clean the CD and load it correctly.

title.E11

this unit has been removed.E30

➪

Replace it.

➪

Press the reset button on the unit. If the "E-77"

code does not disappear, consult your nearest

service center.

➪

Press the reset button on the unit. If the "E-99"

code does not disappear, consult your nearest

service center.

E10

E77

E99A

E02

E04

E-0d: The protective circuit in the unit activates when the

temperature inside the automatic disc changer exceeds 60°C (140°F), stopping all operation.E0d

➪

Cool down the unit by opening the windows or turning on the air conditioner. As the temperature falls below 60°C (140°F), the disc will start playing again.

LOAd: Discs are being exchanged in the Disc changer.

E57

IN (Blink): The CD player section is not operating properly.E59

➪

Reinsert the CD. If the CD cannot be ejected or the display continues to flash even when the CD has been properly reinserted, please switch off the power and consult your nearest service center.

— 22 —

Specifications

Specifications subject to change without notice.

FM tuner section

Frequency range (200 kHz space) ............87.9 MHz – 107.9 MHz

Usable sensitivity (S/N = 30dB) ....................9.3dBf (0.8 µV/75 Ω)

Quieting Sensitivity (S/N = 50dB) ...............15.2dBf (1.6 µV/75 Ω)

Frequency response (±3 dB).................................30 Hz – 15 kHz

Signal to Noise ratio (MONO)..............................................70 dB

Selectivity (±400 kHz).......................................................≥ 80 dB

Stereo separation (1 kHz) ....................................................40 dB

AM tuner section

Frequency range (10 kHz space) ...................530 kHz – 1700 kHz

Usable sensitivity (S/N = 20dB) .............................28 dBµ (25 µV)

CD player section

Laser diode ....................................................GaAlAs (λ=780 nm)

Digital filter (D/A)......................................8 Times Over Sampling

D/A Converter .......................................................................1 Bit

Spindle speed...............................................500 – 200 rpm (CLV)

Wow & Flutter........................................Below Measurable Limit

Frequency response .............................................10 Hz – 20 kHz

Total harmonic distortion (1 kHz) ......................................0.01 %

Signal to Noise ratio (1 kHz) ................................................96 dB

Dynamic range ....................................................................93 dB

Channel separation..............................................................85 dB

Audio section

Maximum output power

KDC-2022/2022V .......................................................50 W x 4

KDC-202MR/222/222S/122/122S...............................45 W x 4

Full Bandwidth Power (at less than 1% THD) ................22 W x 4

Tone action

Bass : ...............................................................100 Hz ±10 dB

Middle : ..............................................................1 kHz ±10 dB

Treble : .............................................................10 kHz ±10 dB

Preout level / Load (during disc play)....................2000 mV/10 kΩ

Preout impedance............................................................≤ 600 Ω

General

Operating voltage (11 – 16V allowable) ..............................14.4 V

Current consumption.............................................................10 A

Installation Size (W x H x D) ..........................182 x 53 x 157 mm

7-3/16 x 2-1/16 x 6-3/16 inch

Weight...................................................................3.1 lbs (1.4 kg)

— 23 —

2Warning

2CAUTION

Use of controls or adjustments or performance of procedures other than those specified

English

herein may result in hazardous radiation exposure. In compliance with Federal Regulations, following are reproductions of labels on, or inside the product relating to laser product safety.

KENWOOD CORPORATION 2967-3, ISHIKAWA-CHO, HACHIOJI-SHI TOKYO, JAPAN

KENWOOD CORP. CERTIFIES THIS EQUIPMENT CONFORMS TO DHHS REGULATIONS N0.21 CFR

1040. 10, CHAPTER 1, SUBCHAPTER J.

Location : Bottom Panel

FCC WARNING

This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made.

NOTE

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment may cause harmful interference to radio communications, if it is not installed and used in accordance with the instructions. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

NOTE

This Class B digital apparatus complies with Canadian ICES-003.

— 24 —

Table des matiéres

Précautions de sécurité............27

Au sujet des CD .......................29

Caractéristiques générales .......30

Alimentation Sélectionner la source Volume Atténuateur Bruit

Français

System Q Commande du son Réglage des enceintes Affichage de l'horloge Régler l'horloge DSI (Disabled System Indicator) Façade antivol

Fonctions du tuner ...................33

Mode d'accord Accord Mémoire de station pré-réglée Entrée en mémoire automatique Accord pré-réglé CRSC (Circuit de réception nette)

Fonctions de contrôle de

CD/disque externe..................35

Lire un CD Lire un disque extérieur Avance rapide et retour Recherche de plages Recherche d'album Répétition de plage/album Balayage des plages Lecture aléatoire Lecture aléatoire du chargeur Recherche de plage directe Recherche directe d'album

Opérations de base de la

télécommande .......................38

Recharger et remplacer la pile Opérations de base En source tuner En source disque

Accessoires ...............................40

Procédure d’installation ...........40

Connexion des câbles sur les

prises ......................................41

Installation ................................42

Guide de depannage .................44

Spécifications ...........................47

— 26 —

Précautions de sécurité

2AVERTISSEMENT

Pour éviter toute blessure et/ou incendie, veuillez prendre les précautions suivantes:

• Insérez l’appareil à fond jusqu’à ce qu’il soit complètement calé. Sinon, il risquerait d’être projeté en cas de collisions ou de cahots.

• Si vous prolongez un câble d’alimentation, de batterie ou de masse, assurez vous d’utiliser un câble pour automobile ou un câble avec une section de 0,75mm d’éviter tous risques de détérioration ou d’endommagement du revêtement des câbles.

• Pour éviter les court-circuits, ne jamais mettre ou laisser d’objets métalliques (comme une pièce de monnaie ou un outil en métal) à l’intérieur de l’appareil.

• Si l’appareil commence à émettre de la fumée ou une odeur bizarre, mettez immédiatement l’appareil hors tension et consultez un revendeur Kenwood.

• Faites attention de ne pas vous prendre les doigts entre la façade et l’appareil.

• Faites attention de ne pas laisser tomber l’appareil ou lui faire subir de chocs importants. L’appareil risque de se casser ou de se fêler car il contient des parties en verre.

• Ne touchez pas le cristal liquide si l’affichage LCD était endommagé ou cassé à cause d’un choc. Le cristal liquide peut être dangereux pour votre santé et même mortel. Si le cristal liquide de l’affichage LCD entrait en contact avec votre corps ou un vêtement, lavez-le immédiatement avec du savon.

(AWG18) afin

2ATTENTION

Pour éviter tout dommage à l'appareil, veuillez prendre les précautions suivantes:

• Assurez-vous de mettre l'appareil à la masse sur une alimentation négative de 12V CC.

• N'ouvrez pas le couvercle supérieur ou inférieur de l'appareil.

• N'installez pas l'appareil dans un endroit exposé directement à la lumière du soleil, à une chaleur excessive ou à l'humidité. Evitez aussi les endroits trop poussiéreux et où l'appareil risque d'être éclaboussé.

• Ne placez pas la façade amovible ou le boîtier de la façade dans un endroit exposé directement à la lumière du soleil, à une chaleur excessive ou à l'humidité. Evitez aussi les endroits trop poussiéreux et où la façade risque d'être éclaboussée.

• Pour éviter toute détérioration, ne touchez pas les contacts de l'appareil ou de la façade avec les doigts.

• Ne faites pas subir de chocs excessifs à la façade car elle fait partie d'un équipement de précision.

• Lors du remplacement d'un fusible, utilisez seulement un fusible neuf avec la valeur indiquée. L'utilisation d'un fusible d'une valeur différente peut être la cause d'un mauvais fonctionnement de votre appareil.

• Pour éviter les courts-circuits lors du remplacement d'un fusible, déconnectez d'abord le faisceau de câbles.

Ne placez aucun objet entre la façade et l'appareil.

•

• Pendant l'installation, n'utilisez aucunes autres vis que celles fournies. L'utilisation de vis incorrectes pourrait endommager l'appareil.

— 27 —

INFORMATION IMPORTANTE Au sujet des lecteurs de CD/changeurs

de disque connectée à cet appareil :

Les changeurs de disque/lecteurs de CD KENWOOD commercialisés en 1998 ou ultérieurement peuvent être connectés à cet appareil. Veuillez-vous référer au catalogue ou consultez votre revendeur Kenwood pour les modèles de changeurs de disque/lecteurs de CD pouvant être connectés. Veuillez prendre note que tous les changeurs de disque/lecteurs de CD KENWOOD commercialisés en 1997 ou précédemment et les changeurs de disque d’autres fabricants ne peuvent être connectés à cet appareil. Les connections non préconisées peuvent causer des dommages. Réglage du commutateur O-N sur la position "N" pour les chargeurs de disque KENWOOD / lecteurs de CD KENWOOD applicables. Les fonctions utilisables et les informations affichables diffèrent suivant les modèles connectés.

Vous pouvez endommager à la fois votre appareil et le changeur de CD si vous les connectez incorrectement.

Ne chargez pas de CD de 8 cm (3 pouces) dans la fenêtre à CD

Si vous essayez de charger un CD de 8 cm avec son adaptateur dans l’appareil, l’adaptateur peut se séparer du CD et endommager l’appareil.

Précautions de sécurité

REMARQUE

• Si vous rencontrez des problèmes pendant l’installation, consultez votre revendeur Kenwood.

• Si l'appareil semble ne pas fonctionner correctement, essayez d'abord d'appuyer sur la touche de réinitialisation. Si cela ne résout pas le problème, consultez votre revendeur Kenwood.

• Appuyez sur la touche de réinitialisation si le changeur CD est commandé en premier et

Français

fonctionne incorrectement. Les conditions de fonctionnement originales seront rappelées.

Touche de réinitialisation

• Les caractères de l’affichage LCD peuvent devenir difficiles à lire quand la température est inférieure à 5 °C (41 °F).

• Les illustrations de l’affichage et du panneau apparaissant dans ce manuel sont des exemples utilisés pour expliquer avec plus de clarté comment les commandes sont utilisées. Il est donc possible que les illustrations d’affichage puissent être différentes de ce qui réellement affiché sur l’appareil et aussi que certaines illustrations représentent des choses impossibles à réaliser en cours de fonctionnement.

Nettoyage des contacts de la façade

Si les contacts de l'appareil ou de la façade deviennent sales, essuyez-les avec un tissu sec et doux.

Nettoyage de l’appareil

Si le panneau avant de cet appareil est taché, essuyez-le avec un chiffon sec et doux comme ceux au silicone. Si le panneau avant est très taché, essuyez-le avec un chiffon imbibé d'un produit de nettoyage neutre et ensuite essuyez toute trace de ce produit.

La pulvérisation directe de produit de nettoyage sur l'appareil risque d'affecter les pièces mécaniques. L'utilisation d'un chiffon rugueux ou d'un liquide volatile tel que solvant ou alcool pour essuyer le panneau avant peut rayer la surface ou effacer des caractères.

REMARQUE

Cet appareil numérique de la classe B est conforme à la morme NMB-003 du Canada.

Nettoyage de la fente à CD

De la poussière peut s’accumuler dans la fenêtre à CD, nettoyez-la occasionnellement. Vos CD peuvent être rayés si vous les introduisez dans une fenêtre poussiéreuse.

Condensation sur la lentille

Juste après avoir mis le chauffage de la voiture par temps froid, de l’humidité risque de se former sur la lentille à l’intérieur du lecteur CD (voile). La reproduction de CD peut être impossible. Dans ce cas, retirez le disque et attendez que l’humidité s’évapore. Si l’appareil ne fonctionne toujours pas normalement après quelques temps, consultez votre revendeur Kenwood.

— 28 —

+ 64 hidden pages