and cancel the demonstration
2 Set the clock and date
3 Set the initial settings
RADIO 6
CD / USB / iPod / ANDROID 7
AUX 10
Pandora® 10
BLUETOOTH® 12
AUDIO SETTINGS 18
DISPLAY SETTINGS 21
TROUBLESHOOTING 22
REFERENCES 24
Maintenance
More information
SPECIFICATIONS 26
INSTALLATION /
CONNECTION 28
IMPORTANT
• To ensure proper use, please read through this manual before using this product. It is especially important
that you read and observe Warning and Caution in this manual.
• Please keep the manual in a safe and accessible place for future reference.
Warning
Do not operate any function that takes your attention away from safe driving.
Caution
Volume setting:
• Adjust the volume so that you can hear sounds outside the car to prevent accidents.
• Lower the volume before playing digital sources to avoid damaging the speakers by the sudden increase of
the output level.
General:
• Avoid using the external device if it might hinder safe driving.
•
Make sure all important data has been backed up. We shall bear no responsibility for any loss of recorded data.
•
Never put or leave any metallic objects (such as coins or metal tools) inside the unit to prevent a short circuit.
• If a disc error occurs due to condensation on the laser lens, eject the disc and wait for the moisture to
evaporate.
• Depending on the types of cars, the antenna will automatically extend when you turn on the unit with the
antenna control wire connected (
a low ceiling area.
Remote control (RC-406):
• Do not leave the remote control in hot places such as on the dashboard.
• The Lithium battery is in danger of explosion if replaced incorrectly. Replace it only with the same or
equivalent type.
• The battery pack or batteries shall not be exposed to excessive heat such as sunshine, fire or the like.
• Keep the battery out of reach of children and in its original packaging when not in used. Dispose of used
batteries promptly. If swallowed, contact a physician immediately.
How to read this manual
• Operations are explained mainly using buttons on the faceplate.
• English indications are used for the purpose of explanation. You can select the display language from the
[
FUNCTION
• [
• (
] menu. ( 5)
XX
] indicates the selected items.
XX) indicates references are available on the stated page.
29). Turn off the unit or change the source to STANDBY when parking at
2
BASICS
FaceplateRemote control (RC-406)
Display windowLoading slot
Lights up when
Bluetooth
connection is
established.
(
12)
How to replace the battery
Remote sensor (Do not
expose to bright sunlight.)
Pull out the
insulation sheet
when using for
the first time.
Reset button
Press twice within
5seconds.
ToOn the faceplateOn the remote control
Turn on the power
Adjust the volumeTurn the volume knob.Press
Select a source
Change the display informationPress DISP repeatedly. (
Volume knobFlashes when the unit
Press
• Press and hold to turn off the power.
Press
enters searching status.
.
repeatedly.
26)( Not available )
Press and hold SRC to turn off the power.
( Pressing SRC does not turn on the power. )
or .
Press ATT during playback to attenuate the sound.
• Press again to cancel.
Press SRC repeatedly.
ENGLISH
3
GETTING STARTED
1
Select the display language and cancel the demonstration
When you turn on the power for the first time (or [
[
YES
], 5), the display shows: “SEL LANGUAGE” “PRESS” “VOLUME
KNOB”
1 Turn the volume knob to select [
then press the knob.
[
ENG
] is selected for the initial setup.
Then, the display shows: “CANCEL DEMO”
KNOB”.
ENG
2 Press the volume knob.
[
YES
] is selected for the initial setup.
3 Press the volume knob again.
“DEMO OFF” appears.
Then, the display shows the selected crossover type:
“2-WAY X ’ OVER” or “3-WAY X ’ OVER”
• To change the crossover type, see “Change the crossover type” (
FACTORY RESET
] (English) or [
“PRESS” “VOLUME
TUR
] (Turkish),
] is set to
5).
2
Set the clock and date
Press the volume knob to enter [
1
2 Turn the volume knob to select [
To adjust the clock
3 Turn the volume knob to select [
FUNCTION
].
CLOCK
], then press the knob.
CLOCK ADJUST
], then press the knob.
4 Turn the volume knob to make the settings, then press the knob.
Hour
5 Turn the volume knob to select [
6 Turn the volume knob to select [
To set the date
7 Turn the volume knob to select [
8 Turn the volume knob to select [
9 Turn the volume knob to select [
the knob.
Minute
CLOCK FORMAT
12H
] or [
24H
], then press the knob.
DATE FORMAT
DD/MM/YY
DATE SET
], then press the knob.
] or [
], then press the knob.
], then press the knob.
MM/DD/YY
], then press
10 Turn the volume knob to make the settings, then press the knob.
Day
Month Year or Month Day Year
11 Press and hold to exit.
To return to the previous setting item, press .
3
Set the initial settings
Press repeatedly to enter STANDBY.
1
2 Press the volume knob to enter [
3 Turn the volume knob to select an item (
FUNCTION
].
5
), then press the knob.
4 Repeat step 3 until the desired item is selected or activated.
5 Press and hold to exit.
To return to the previous setting item, press .
4
GETTING STARTED
DISPLAY
EASY MENU
TUNER SETTING
PRESET TYPE
SYSTEM
KEY BEEP*
SOURCE SELECT
PANDORA SRC
BUILT-IN AUX ON
CD READ1
F/W UPDATE
UPDATE SYSTEM
F/W UP xx.xx
FACTORY RESET YES
*
Not applicable if 3-way crossover is selected.
When entering [
ON
:ZONE1 and ZONE2 illuminations change to white color.;
illumination changes to white color while ZONE1 illumination remains as
[
COLORSELECT
(Refer to the illustration on page 21 for zone identification.)
NORMAL
(FM1/ FM2/ FM3/ AM/ SW1/ SW2).;
each preset button, regardless of the selected band.
ON
:Activates the keypress tone.;
ON
:Enables PANDORA in source selection.;
:Enables AUX in source selection.;
:Automatically distinguishes between audio file disc and music CD.;
2
:Forces to play as a music CD. No sound can be heard if an audio file
disc is played.
YES
activated).
For details on how to update the firmware, see:
www.kenwood.com/cs/ce/
NO
:Cancels.
FUNCTION
] color. ( 21)
:Memorizes one station for each preset button in each band
:Starts upgrading the firmware.; NO:Cancels (upgrading is not
:Resets the settings to default (except the stored station).;
Default:
XX
CLOCK
]...
OFF
:ZONE2
CLOCK DISPLAY
ENGLISH
TURKCE
ON
:The clock time is shown on the display even when the unit is turned
off.;
OFF
:Cancels.
Select the display language for [
information if applicable.
By default, [
ENGLISH
] is selected.
FUNCTION
] menu and music
Change the crossover type
Press repeatedly to enter STANDBY.
MIX
:Memorizes one station for
1
2 Press and hold number buttons 4 and 5 to enter crossover select.
The current crossover type appears.
3 Turn the volume knob to select “2WAY” or “3WAY”, then press the
OFF
:Deactivates.
OFF
OFF
:Disables. ( 10)
:Disables. ( 10)
knob.
4 Turn the volume knob to select “YES” or “NO”, then press the knob.
The selected crossover type appears.
• To cancel, press and hold
• To adjust the selected crossover settings, (
.
19).
Caution
Select a crossover type according to how the speakers are connected.
(
29)
If you select a wrong type:
• The speakers may damage.
• The output sound level may be extremely high or low.
ENGLISH
5
RADIO
Search for a station
Press repeatedly to select TUNER.
1
2 Press repeatedly (or press on RC-406) to select
FM1/ FM2/ FM3/ AM/ SW1/ SW2.
3 Press (or press on RC-406) to search for a station.
• To change the searching method for : Press repeatedly.
AUTO1 : Automatically search for a station.
AUTO2 : Search for a preset station.
MANUAL : Manually search for a station.
• To store a station: Press and hold one of the number buttons (1to6).
• To select a stored station: Press one of the number buttons (1to6) (or press
one of the number buttons (1to6) on RC-406).
Direct Access Tuning (using RC-406)
Press DIRECT to enter Direct Access Tuning.
1
2 Press the number buttons to enter a frequency.
3 Press to search for a station.
• To cancel, press or DIRECT.
• If no operation is done for 10seconds after step
automatically canceled.
2, Direct Access Tuning is
Other settings
Press the volume knob to enter [
1
FUNCTION
].
2 Turn the volume knob to select an item (see the following
table), then press the knob.
3 Repeat step 2 until the desired item is selected or activated.
4 Press and hold to exit.
To return to the previous setting item, press .
Default:
TUNER SETTING
LOCAL SEEK
AUTO MEMORYYES
MONO SETON
NEWS SETON
REGIONALON
AF SETON
ON
:Searches only AM/ SW1/ SW2 stations with good
reception. ;
OFF
•
Settings made are applicable only to the selected source/
station. Once you change the source/station, you need to
make the settings again.
reception.;
•
Selectable only if [
[
PRESET TYPE
:Improves the FM reception, but the stereo effect may be
lost.;
: The unit will temporarily switch to News Programme if
available. ;
: Switches to another station only in the specific region
using the “AF” control.;
: Automatically searches for another station broadcasting
the same program in the same Radio Data System network
with better reception when the current reception is poor.;
OFF
:Cancels.
:Automatically starts memorizing 6 stations with good
NO
:Cancels.
NORMAL
OFF
:Cancels.
] is selected for
OFF
:Cancels.
:Cancels.
OFF
: Cancels.
]. ( 5)
XX
6
RADIO
CD / USB / iPod / ANDROID
TION
:Allows the unit to temporarily switch to Traffic Information if
available (“TI” lights up).;
OFF
:Cancels.
PTY SEARCH1 Press the volume knob to enter PTY language selection.
2
Turn the volume knob to select the PTY language (
FRENCH/ GERMAN
3
Turn the volume knob to select the available Program Type
), then press the knob.
ENGLISH
(see the following).
4
Press to start searching.
CLOCK
TIME SYNC
ON
:Synchronizes the unit’s time to the Radio Data System station
The unit will search for the Program Type categorized under
[
SPEECH
] or [
MUSIC
] if selected.
MONO SET
]/ [
NEWS SET
]/ [
REGIONAL
]/ [
AF SET
]/ [TI]/ [
• [
PTY SEARCH
] is
selectable only when the band is FM1/ FM2/ FM3.
• If the volume is adjusted during reception of traffic information
or news bulletin, the adjusted volume is memorized
automatically. It will be applied the next time traffic information
or news bulletin is turned on.
Start playback
The source changes automatically and playback starts.
/
Label side
M
Eject disc
USB input terminal
USB
CA-U1EX (max.: 500mA) (optional accessory)
iPod/iPhone
KCA-iP102 / KCA-iP103 (optional accessory)
or accessory cable of the iPod/iPhone
3
ANDROID
*
Micro USB 2.0 cable
2
*
*
2
*
(commercially available)
1
*
KCA-iP102 : 30-pin type, KCA-iP103 : Lightning type
2
*
Do not leave the cable inside the car when not using.
3
*
When connecting an Android device, “Press [VIEW] to install KENWOOD MUSIC PLAY APP” is
shown. Follow the instructions to install the application. You can also install the latest version of
KENWOOD MUSIC PLAY application on your Android device before connecting. (
1
24)
ENGLISH
7
CD / USB / iPod / ANDROID
ToOn the faceplateOn the remote control
Playback / pausePress .
4
Reverse / Fast-forward
Select a track/filePress
Select a folder
6
Repeat play
*
*
Press and hold .Press and hold .
.Press .
5
*
Press .Press .
Press repeatedly.
TRACK REPEAT/ ALL REPEAT
FILE REPEAT/ FOLDER REPEAT/ ALL REPEAT
FILE REPEAT/ FOLDER REPEAT/ REPEAT OFF
6
Random play
*
Press repeatedly.
DISC RANDOM/ RANDOM OFF
FOLDER RANDOM/ RANDOM OFF
Press and hold
4
*
For ANDROID: Applicable only when [
5
*
For CD: Only for MP3/WMA/AAC files. This does not work for iPod/ ANDROID.
6
*
For iPod/ ANDROID: Applicable only when [
7
*
For CD: Only for MP3/WMA/AAC files.
BROWSE MODE
MODE OFF
to select
] is selected.
]/ [
BROWSE MODE
: Audio CD
Press
: MP3/WMA/AAC/WAV/FLAC
file
: iPod or ANDROID
: Audio CD
: MP3/WMA/AAC/WAV/FLAC file, iPod
or ANDROID
7
ALL RANDOM
*
.
] is selected.
Select control mode
While in IPOD source, press 5 repeatedly.
MODE ON
: Control iPod using the iPod itself.
However, you can still play/pause, file
skip, fast-forward or reverse from this
unit.
MODE OFF
: Control iPod from this unit.
While in ANDROID source, press 5 repeatedly.
BROWSE MODE
: Control Android device from this
unit via KENWOOD MUSIC PLAY
application installed in the Android
device.
.
HAND MODE
: Control Android device using the
Android device itself via other
media player applications installed
in the Android device. However,
you can still play/pause and file skip
from this unit.
Select music drive
Press 5 repeatedly.
Stored songs in the following drive will be played
back.
• Selected internal or external memory of a
smartphone (Mass Storage Class).
• Selected drive of a multiple drives device.
8
CD / USB / iPod / ANDROID
Select a file from a folder/list
Press .
1
2 Turn the volume knob to select a folder/list, then press the knob.
3 Turn the volume knob to select a file, then press the knob.
Quick Search
If you have many files, you can search through them quickly.
Turn the volume knob quickly to browse through the list quickly.
–
Not applicable for iPod.
(or)
Press to search at a preset skip search ratio.
(
[SKIP SEARCH
• Pressing and holding
– Not applicable for audio CD and MP3/ WMA/ AAC/ WAV/ FLAC files.
(or)
Alphabet search
If you have many files in the iPod, you can search through them
quickly according to the first character of the file name.
])
searches at a 10% ratio.
(applicable only for iPod)
Turn the volume knob quickly to enter character search.Turn the volume knob to select the character.
To search for a character other than A to Z and 0to9, enter only
“
”.
*
Press S/T to move to the entry position.
• You can enter up to 3characters.
Press the volume knob to start searching.
• To return to the root folder/ first file/ top menu, press 5. (
for BT AUDIO source.
• To return to the previous setting item, press
• To cancel, press and hold
• For iPod, applicable only when [
• For ANDROID, applicable only when [
)
.
MODE OFF
] is selected.
BROWSE MODE
Not applicable
.
( 8)
] is selected.
( 8)
Listen to TuneIn Radio/ TuneIn Radio Pro/ Aupeo
While listening to TuneIn Radio, TuneIn Radio Pro or Aupeo, connect the
iPod/iPhone to the USB input terminal of the unit.
• The unit will output the sound from these applications.
Direct Music Search (using RC-406)
Press DIRECT.
1
2 Press the number buttons to enter a track/file number.
3 Press to search for music.
• To cancel, press
• Not available if Random Play is selected.
• Not applicable for iPod and ANDROID.
or DIRECT.
Other settings
Press the volume knob to enter [
1
FUNCTION
].
2 Turn the volume knob to select an item (see the following table),
then press the knob.
3 Repeat step 2 until the desired item is selected or activated.
4 Press and hold to exit.
To return to the previous setting item, press .
Default:
USB
MUSIC DRIVEDRIVE CHANGE
automatically and playback starts.
Repeat steps
SKIP SEARCH0.5%/ 1%/ 5%/ 10%
skip search ratio over the total files.
:The next drive ([
1
to 3 to select the following drives.
DRIVE 1
] to [
: While listening to iPod or ANDROID, selects the
DRIVE 4
]) is selected
XX
ENGLISH
9
AUX
Preparation:
Select [
ON
] for [
BUILT-IN AUX
Start listening
Connect a portable audio player (commercially
1
available).
Auxiliary input jack
3.5mm stereo mini plug with “L” shaped
connector (commercially available)
2 Press repeatedly to select AUX.
3 Turn on the portable audio player and start playback.
Set the AUX name
While listening to a portable audio player connected to the
unit...
1 Press the volume knob to enter [
2 Turn the volume knob to select [
knob.
3 Turn the volume knob to select [
the knob.
4 Turn the volume knob to select an item, then press the
knob.
AUX
(default)/
5 Press and hold to exit.
To return to the previous setting item, press .
]. ( 5)
Portable audio player
FUNCTION
SYSTEM
], then press the
AUX NAME SET
DVD/ PORTABLE/ GAME/ VIDEO/ TV
].
], then press
Pandora®
Preparation:
Install the latest version of the Pandora application on your device (iPhone/ iPod
touch), then create an account and log in to Pandora.
• Select [
ON
] for [
PANDORA SRC
Start listening
Open the Pandora application on your device.
1
2 Connect your device to the USB input terminal.
USB input terminal
3 Press repeatedly to select PANDORA.
Broadcast starts automatically.
ToOn the faceplateOn the remote control
Playback / pause
Skip a track
Thumbs up or thumbs
3
*
down
1
*
KCA-iP102 : 30-pin type, KCA-iP103 : Lightning type
2
*
Do not leave the cable inside the car when not using.
3
*
If thumbs down is selected, the current track is skipped.
]. ( 5)
KCA-iP102 / KCA-iP103 (optional accessory)
accessory cable of the iPod/iPhone
Press
Press T.
Press .
2
*
.Press
*
1
or
Press
Press
.
.
/ .
10
Pandora®
Create and save a new station
Press .
1
2 Turn the volume knob to select [
3 Turn the volume knob to select [
press the knob.
A new station is created based on the current song or artist.
NEW STATION
FROM TRACK
], then press the knob.
] or [
FROM ARTIST
], then
4 Press and hold one of the number buttons (1to5) to store.
To select a stored station, press one of the number buttons (1to5).
Search for a registered station
Press .
1
2 Turn the volume knob to select an item, then press the knob.
[
SORT BY DATE
[
SORT BY A-Z
]:According to the registered date
]:Alphabetical order
3 Turn the volume knob to select the desired station, then press the
knob.
To cancel, press and hold
.
(or using RC-406)
Press J / K to search for a station, then press .
Bookmark current song information
Press and hold the volume knob.
“BOOKMARKED” appears and the information is stored to your device.
The bookmark is available on your Pandora account but not on this unit.
Delete a station
While listening to PANDORA...
1 Press the volume knob to enter [
2 Turn the volume knob to select [
3 Turn the volume knob to select [
4 Turn the volume knob to select [
press the knob.
FUNCTION
].
SYSTEM
], then press the knob.
STATION DEL
SORT BY A-Z
], then press the knob.
] or [
SORT BY DATE
], then
5 Turn the volume knob to select the desired station to delete, then
press the knob.
6 Turn the volume knob to select [
YES
], then press the knob.
7 Press and hold to exit.
To return to the previous setting item, press .
ENGLISH
11
BLUETOOTH®
BLUETOOTH — Connection
Supported Bluetooth profiles
– Hands-Free Profile (HFP)
– Advanced Audio Distribution Profile (A2DP)
– Audio/Video Remote Control Profile (AVRCP)
– Serial Port Profile (SPP)
– Phonebook Access Profile (PBAP)
Connect the microphone
Rear panel
Microphone
(supplied)
Microphone input
jack
Secure using cord clamps (not
supplied) if necessary.
Pair and connect a Bluetooth device for the first time
Press to turn on the unit.
1
2 Search and select this unit model name (DPX-50
“PAIRING”
the display.
“PASS XXXXXX” Device name “PRESS” “VOLUME KNOB” scrolls on
• For some Bluetooth devices, you may need to enter the Personal Identification
Number (PIN) code immediately after searching.
3 Press the volume knob to start pairing.
“PAIRING OK” appears when pairing is completed.
Supported Bluetooth codecs
– Sub Band Codec (SBC)
– Advanced Audio Coding (AAC)
Adjust the microphone
angle
BT) on the Bluetooth device.
**
• This unit supports Secure Simple Pairing (SSP).
• Up to 10 devices can be registered (paired) in total.
• Once the pairing is completed, the Bluetooth device
will remain registered in the unit even if you reset the
unit. To delete the paired device,
Once pairing is completed, Bluetooth connection is
established automatically. “BT1” and/or “BT2” indicator
on the faceplate lights up.
• A maximum of two Bluetooth phones and one
Bluetooth audio device can be connected at any time.
• Some Bluetooth devices may not automatically
connect to the unit after pairing. Connect the device
to the unit manually.
• Refer to the instruction manual of the Bluetooth
device for more information.
16, [
DEVICE DELETE
Auto Pairing
When you connect iPhone/ iPod touch/ Android
device to the USB input terminal, pairing request (via
Bluetooth) is automatically activated.
Press the volume knob to pair once you have
confirmed the device name.
Automatic pairing request is activated only if:
– Bluetooth function of the connected device is turned
on.
– [
AUTO PAIRING
– KENWOOD MUSIC PLAY application is installed on the
Android device (
(
8).
] is set to [ON]. ( 16)
7) and [
BROWSE MODE
] is selected
].
12
BLUETOOTH®
Connect with a remote device by One-touch
(NFC)
Near Field Communication (NFC) enables short-range
wireless communication between the unit and remote
devices.
By holding an NFC-compatible remote device near to
the N-Mark on the unit, the unit and remote device
proceed to complete pairing and established the
BLUETOOTH connection automatically.
1 Activate the NFC function on the remote device.
Refer to the instruction manual of the remote
device for more information.
2 Hold the remote device near to the N-Mark on the
unit.
The device vibrates when pairing is completed.
• To disconnect, hold the remote device near to the
N-Mark on the unit again.
• This unit only can recognize and connect to one NFCcompatible device at a time.
BLUETOOTH — Mobile phone
Receive a call
When there is an incoming call:
• ZONE 2 illuminates in green color and flashes.
• The unit answers the call automatically if [
During a call:
• The display illuminates according to the settings made for [
illuminates in green color.
• If you turn off the unit, the Bluetooth connection is disconnected.
The following operations may differ or not available depending on the connected phone.
ToOn the faceplateOn the remote control
First incoming call...
Answer a call
Reject a call
End a call
Press
of the number buttons (1 to 6).
Press
Press
AUTO ANSWER
or the volume knob or one
.
.
] is set to a selected time. ( 14)
DISPLAY
] ( 21) and ZONE 2
Press
.
Press
.
Press
.
ENGLISH
13
BLUETOOTH®
ToOn the faceplateOn the remote control
While talking on the first incoming call...
Answer another incoming
call and hold the current
call
Reject another incoming
call
While having two active calls...
End current call and
activate held call
Swap between the
current call and held call
Adjust the phone volume
[00]
to
[35]
(Default:
Switch between hands-free
and private talk modes
[15]
Improve the voice quality
While talking on the phone...
1 Press the volume knob to enter [
2 Turn the volume knob to select an item (see the following table), then press the
knob.
3 Repeat step 2 until the desired item is selected or activated.
4 Press and hold to exit.
To return to the previous setting item, press .
Press
Press
Press
Press
Turn the volume knob during
)
a call.
• This adjustment will not
Press
• Operations may vary
.
.
affect the volume of the other
sources.
during a call.
according to the connected
Bluetooth device.
FUNCTION
Press
.
Press
.
.
].
.
Press
.
Press
.
( Not available )
( Not available )
Default:
MIC GAIN–10
NR LEVEL–5
ECHO CANCEL–5
—
+10(–4
microphone increases as the number increased.
—+5(0):Adjust the noise reduction level
until the least noise is being heard during a phone
conversation.
—+5(0):Adjust the echo cancellation delay
time until the least echo is being heard during a
phone conversation.
):The sensitivity of the
Make the settings for receiving a call
Press to enter Bluetooth mode.
1
2 Turn the volume knob to select an item (see the
following table), then press the knob.
3 Repeat step 2 until the desired item is selected or
activated.
4 Press and hold to exit.
To return to the previous setting item, press .
Default:
SETTINGS
AUTO ANSWER
BATT/SIGNAL* AUTO
*
Functionality depends on the type of the phone used.
1
—30:The unit answers incoming call
automatically in the selected time (in seconds).;
OFF
:Cancels.
:Shows the strength of the battery and signal
when the unit detects a Bluetooth device and the
Bluetooth device is connected.;
time is shown.
OFF
:Cancels. Clock
XX
XX
14
BLUETOOTH®
Make a call
You can make a call from the call history, phonebook, or dialing the number. Call
by voice is also possible if your mobile phone has the feature.
1 Press to enter Bluetooth mode.
2 Turn the volume knob to select an item (see the following table), then
press the knob.
3 Repeat step 2 until the desired item is selected/activated or follow the
instructions stated on the selected item.
4 Press and hold to exit.
To return to the previous setting item, press .
CALL HISTORY
PHONE BOOK
(Applicable only if the phone supports PBAP)
1
Press the volume knob to select a name or a phone number.
• “INCOMING”, “OUTGOING”, or “MISSED” is shown on the lower part of the
display to indicate the previous call status.
• Press
DISP
• “NO DATA” appears if there is no recorded call history.
2
Press the volume knob to call.
(Applicable only if the phone supports PBAP)
1
Turn the volume knob quickly to enter alphabet search mode (if the
phonebook contains many contacts).
The first menu (ABCDEFGHIJK) appears.
• To go to the other menu (LMNOPQRSTUV or WXYZ1
• To select the desired first letter, turn the volume knob or press
Select “1” to search with numbers and select “
2
Turn the volume knob to select a name, then press the knob.
3
Turn the volume knob to select a phone number, then press the knob to call.
•
The phonebook of the connected phone is automatically transferred to the unit
when pairing.
•
Contacts are categorized as: HOME, OFFICE, MOBILE, OTHER, GENERAL
•
This unit can display only non-accent letters. (Accent letters such as “Ú” is
showns as “U”.)
to change the display category (NUMBER or NAME).
then press the knob.
), press .
*
” to search with symbols.
*
NUMBER DIAL
VOICE
BATT LOW/ MID/ FULL*:Shows the strength of the battery.
NO SIGNAL/ LOW/ MID/ MAX*:Shows the strength of the current received signal.
*
Functionality depends on the type of the phone used.
1
Turn the volume knob to select a number (0 to 9) or
character (
2
Press to move the entry position.
3
Press the volume knob to call.
1
Press the number buttons (0 to 9) to enter the phone
2
Press to call.
Speak the name of the contact you want to call or the voice
command to control the phone functions.
(
, #, +).
Repeat steps
number.
(or using RC-406)
number.
Make a call using voice recognition
1
and 2 until you finish entering the phone
)
Make a call using voice recognition
Press and hold to activate the voice recognition of the
1
connected phone.
2 Speak the name of the contact you want to call or the voice
command to control the phone functions.
• Supported Voice Recognition features vary for each phone.
,
Refer to the instruction manual of the connected phone for
details.
• This unit also supports the intelligent personal assistant function
of iPhone.
ENGLISH
15
BLUETOOTH®
Settings in memory
Store a contact in memory
You can store up to 6 contacts into the number buttons
(1 to 6).
1 Press to enter Bluetooth mode.
2 Turn the volume knob to select [
BOOK
], or [
NUMBER DIAL
], then press the knob.
CALL HISTORY
], [
PHONE
3 Turn the volume knob to select a contact or enter a
phone number.
If a contact is selected, press the volume knob to show the
phone number.
4 Press and hold one of the number buttons (1 to 6).
“STORED” appears when the contact is stored.
To erase a contact from the preset memory, select [
DIAL
] in step 2 and store a blank number.
NUMBER
Make a call from memory
Press to enter Bluetooth mode.
1
2 Press one of the number buttons (1 to 6).
3 Press the volume knob to call.
“NO MEMORY” appears if there is no contacts stored.
Other settings
Press the volume knob to enter
1
[FUNCTION
].
2 Turn the volume knob to select an item (see the following table), then press
the knob.
3 Repeat step 2 until the desired item is selected/activated or follow the
instructions stated on the selected item.
4 Press and hold to exit.
To return to the previous setting item, press .
Default:
BT MODE
PHONE SELECT
AUDIO SELECT
DEVICE DELETE
PIN CODE EDIT
(0000)
RECONNECTON
AUTO PAIRINGON
INITIALIZEYES
Selects the phone or audio device to connect or disconnect.
“
” appears in front of the device name when connected.
*
•
You can only connect a maximum of two Bluetooth phones and one Bluetooth
audio device at any time.
1
Turn the volume knob to select a device to delete, then press the knob.
2
Turn the volume knob to select [
Changes the PIN code (up to 6 digits).
1
Turn the volume knob to select a number.
2
Press to move the entry position.
Repeat steps
3
Press the volume knob to confirm.
:The unit automatically reconnect when the last connected Bluetooth device is
within range.;
:The unit automatically pair supported Bluetooth device (iPhone/ iPod touch/
Android device) when it is connected through USB input terminal.Depending
on the operating system of the connected device, this function may not work. ;
OFF
:Cancels.
:Initializes all the Bluetooth settings (including stored pairing, phonebook, and
etc.).;
1
and 2 until you finish entering the PIN code.
OFF
:Cancels.
NO
:Cancels.
YES
] or [NO], then press the knob.
XX
16
BLUETOOTH®
Bluetooth test mode
You can check the connectivity of the
supported profile between the Bluetooth
device and the unit.
• Make sure there is no Bluetooth device
paired.
1 Press and hold .
“PLEASE PAIR YOUR PHONE PIN 0000”
appears.
2 Search and select this unit model name
(DPX-50
3 Operate the Bluetooth device to confirm
pairing.
“TESTING” flashes on the display.
The connectivity result (OK or NG) appears
after the test.
PAIRING: Pairing status
HF CNT: Hands-Free Profile (HFP)
AUD CNT: Advanced Audio Distribution
PB DL: Phonebook Access profile (PBAP)
To cancel test mode, press and hold
turn off the unit.
BT) on the Bluetooth device.
**
compatibility
Profile (A2DP) compatibility
compatibility
to
BLUETOOTH — Audio
Audio player via Bluetooth
Press repeatedly to select BTAUDIO (or press SRC on RC-406).
1
2 Operate the Bluetooth audio player to start playback.
ToOn the faceplateOn the remote control
Playback / pause
Select group or folderPress
Reverse / Forward skipPress
Reverse / Fast-forwardPress and hold
Repeat playPress
Random playPress and hold
Select a file from a
folder/list
Operations and display indications may differ according to their availability on the connected device.
Press
ALL REPEAT, FILE REPEAT, REPEAT OFF
ALL RANDOM
• Press
Refer to “Select a file from a folder/
list” on page 9.
.Press
.Press .
.Press .
.Press and hold .
repeatedly.
to select
.
to select
RANDOM OFF
( Not available )
( Not available )
.
( Not available )
.
ENGLISH
17
BLUETOOTH®
Internet radio via Bluetooth
Listen to Pandora
You can listen to Pandora on the Android device via
Bluetooth on this unit.
Preparation:
Select [
ON
] for [
PANDORA SRC
1 Open the Pandora application on your device.
2 Connect your Bluetooth audio player via
Bluetooth connection. (
3 Press repeatedly to select PANDORA.
The source switches and broadcast starts
automatically.
You can operate Pandora in the same way as Pandora
for iPod/iPhone. (
]. ( 5)
12)
10)
AUDIO SETTINGS
While listening to any source...
1 Press AUD to enter [
2 Turn the volume knob to select an item (see the following table), then press the knob.
3 Repeat step 2 until the desired item is selected or activated.
4 Press and hold to exit.
(or using RC-406)
1 Press AUD to enter [
2 Press to select an item, then press .
To return to the previous setting item, press
SUB-W LEVEL–50
MANUAL EQ
BAND1 LEVELLEVEL
BAND2 LEVEL
BAND13 LEVEL
Q FACTOR1.35/ 1.50/ 2.00
PRESET EQNATURAL/ ROCK/ POPS/ EASY/ TOP40/ JAZZ/ POWERFUL/ USER
BASS BOOSTLEVEL1/ LEVEL2/ LEVEL3/ LEVEL4/ LEVEL5
LOUDNESSLEVEL1/ LEVEL2
to
AUDIO CONTROL
AUDIO CONTROL
to
+10 (0
BASS EXTENDON
–9
to +9 (0): The sound elements (frequency level, tone level, Q factor) are preset into each
selection (
BAND1 LEVEL
Adjusts the level to memorize for each source. (Before making an adjustment, select the
source you want to adjust.)
equalizer suitable to the music genre. (Select [
EQ
].)
OFF
:Cancels.
balanced sound at a low volume level.;
].
].
.
Default:
): Adjusts the subwoofer output level.
–9
to +9 (0):(Refer to
:Turns on the extended bass.;
to
BAND13 LEVEL
:Adjust the quality factor.
:Selects your preferred low and high frequencies boost to produce a well-
BAND2 LEVEL
).
OFF
:Cancels.
below.)
OFF
:Cancels.
USER
] to use the settings made in [
:Selects your preferred bass boost level.;
: Selects a preset
MANUAL
XX
18
Loading...
+ 42 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.