Kenwood BLM802GY User Manual
Type BLM80
instructions
English 2 - 9
´¸∂w
01
- 71
br
bs
bq
1
2
3
4
5
6
8
9
7
bk bl bm bn bo bp
4
2
3
1
Y
our Blend-X PRO blender has 6 pre-set
programmes available for all core blending tasks plus
the flexibility of variable speed and pulse for total
c
ontrol. Each programme has been set to provide the
perfect consistency every time, whether its puréeing
ingredients for soups, crushing ice for cocktails,
b
lending breakfast smoothies, grinding coffee or
preparing salsa.
b
efore using your Kenwood appliance
●
Read these instructions carefully and retain for future
reference.
●
R
emove all packaging and any labels.
●
Wash the parts: see ‘care and cleaning’.
safety
IMPORTANT: HOT BLENDING INSTRUCTIONS
To minimise the possibility of scalding when blending hot
ingredients keep hands and other exposed skin away from the lid
to prevent possible burns. The following precautions must be
observed:
●
CAUTION: Blending very hot ingredients may result
in hot liquid and steam being forced suddenly past
the lid or filler cap
1
.
●
We recommend that hot ingredients are allowed to
cool before blending.
●
NEVER exceed 1200ml / 5 cups capacity if processing hot
liquids, such as soups (refer to the markings on the goblet).
●
ALWAYS use the pre-set “Soup” program
bl
for blending hot
liquids and NEVER use the pulse setting.
●
Liquids which tend to foam such as milk, should be limited to
a maximum capacity of 1000ml/4 cups.
●
Take care when handling the blender as the goblet and its
contents will be very hot.
●
Take particular care when removing the lid. The lid is designed
to be a tight fit to prevent leakage. If necessary protect your
hands with a cloth or oven gloves when handling.
●
Ensure the goblet is securely attached to the base and when
removing from the appliance, guide the base and ensure it is
removed together with the goblet.
●
Ensure that the lid and filler cap are securely in place before
every blending operation.
2
safety
●
Switch off and unplug:
●
before fitting or removing parts;
●
when not in use;
●
before cleaning.
●
Never fit the blade unit to the power unit without the
blender goblet fitted.
●
Ensure the cord is fully unwound from the cord
storage device
s
before using the blender.
●
Always unplug the appliance before putting your hands or
utensils in the goblet.
●
The blender lid must be fitted when using the stir stick in the
goblet.
●
Only use the stir stick
r
for processing cold ingredients. DO
NOT use when processing hot liquids.
●
Always take care when handling the blade assembly and avoid
touching the cutting edge of the blades when cleaning.
●
Only operate the blender with the lid in place.
●
Only use the goblet with the blade assembly supplied.
●
Never let the power unit, cord or plug get wet.
●
Never use a damaged appliance. Get it checked or repaired: see
‘service and customer care’.
●
Never use an unauthorised attachment.
●
SCALD RISK: Hot ingredients should be allowed to cool to
room temperature before blending.
●
Never leave the appliance unattended when it is operating.
3
●
Always ensure that the vents in the filler cap are clear before
every blending operation
q
.
●
When fitting the lid to the goblet always ensure that the lid and
goblet rim are clean and dry to ensure a good seal and
prevent spillage.
4
●
When removing the blender from the power unit:
●
wait until the blades have completely stopped;
●
don’t accidentally unscrew the goblet from the blade
assembly.
●
Never run the blender empty.
●
Never blend more than the maximum capacity stated in the
recommended speed chart.
●
To ensure long life of your blender, do not run it for longer than
3 minutes.
●
Smoothie recipes - never blend frozen ingredients that have
formed a solid mass during freezing, break it up before adding
to the goblet.
●
This appliance shall not be used by children. Keep the appliance
and its cord out of reach of children.
●
Do not process hard spices such as Nutmeg or Turmeric root
as they may damage the blade.
●
Don’t use the blender as a storage container. Keep it empty
before and after use.
●
Always use the blender on a secure, dry level surface.
●
Never place this appliance on or near a hot gas or electric
burner or where it could touch a heated appliance.
●
Important - The skirt on the base of the goblet is fitted during
manufacture and no attempt should be made to remove it.
●
Misuse of your blender can result in injury.
●
Appliances can be used by persons with reduced physical,
sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or instruction
concerning use of the appliance in a safe way and if they
understand the hazards involved.
●
Only use the appliance for its intended domestic use. Kenwood
will not accept any liability if the appliance is subject to improper
use, or failure to comply with these instructions.
b
efore plugging in
●
Make sure your electricity supply is the same as the
o
ne shown on the underside of the appliance.
I
mportant – UK only
●
The wires in the cord are coloured as follows:
Green and Yellow = Earth, Blue = Neutral, Brown =
L
ive.
●
The appliance must be protected by a 13A approved
(BS1362) fuse.
WARNING: THIS APPLIANCE MUST BE
EARTHED.
Note:
●
For non-rewireable plugs the fuse cover MUST be
refitted when replacing the fuse. If the fuse cover is
lost then the plug must not be used until a
replacement can be obtained. The correct fuse cover
is identified by colour and a replacement may be
obtained from your Kenwood Authorised Repairer
(see Service).
●
If a non-rewireable plug is cut off it must be
DESTROYED IMMEDIATELY. An electric shock hazard
may arise if an unwanted non-rewireable plug is
inadvertently inserted into a 13A socket outlet.
●
This appliance conforms to EC directive 2004/108/EC
on Electromagnetic Compatibility and EC regulation
no. 1935/2004 of 27/10/2004 on materials intended
for contact with food.
key
1
filler cap
2
lid
3
goblet
4
sealing ring
5
blade unit
6
blade base
7
Power On indicator
8
speed + pulse control
9
power unit
k
drinks programme button
l
soups programme button
m
ice crush programme button
n
fine chop programme button
o
coarse chop programme button
p
rinse programme button
q
vents
r
stir stick
s
cord storage device
to use your blender
1 Fit the sealing ring 4into the blade unit 5- ensuring
the seal is located correctly in the grooved area. Then
f
it the blade unit into the goblet
3
.
●
Leaking will occur if the seal is damaged or
incorrectly fitted.
2
Screw the blade base
6
o
nto the goblet – ensuring
the blade assembly is fully tightened. Refer to the
graphics on the side of the blade base as follows:
- unlocked position
- locked position
3 Put your ingredients into the goblet.
4 Fit the filler cap to the lid and push down to secure.
5 Fit the lid by pushing down until secure.
6 Place the blender onto the power unit.
●
Ensure the cord is fully unwound from the
cord storage device before using the
blender.
●
The appliance will not work if the blender is
incorrectly fitted.
7 Plug in and the Power On indicator
7
will light up.
Note: The Power On indicator will flash if the goblet is
not fitted to the power unit. Select a speed (refer to
the recommended speed chart).
8 Choose one of the following options:
●
Programme buttons:- Turn the speed control to the
‘On’ position and all the buttons will light up. Press
the required programme button and the lights on the
other buttons will go out and the programme will
start. The blender will switch off automatically at the
end of the programme time. If you wish to stop before
the programme time has elapsed, press the selected
programme button again.
●
Manually selected a speed by turning the speed
control until the required speed is reached. At the end
of blending return the speed control to “O” before
removing the blender.
●
Do not remove the goblet until the blades
have stopped rotating and the speed control
is in the ‘O’ position.
●
(P) Pulse – operates the motor in a start/stop action.
The pulse will operate for as long as it is held in
position.
Refer to the troubleshooting section if you
experience any problems with the operation of
the blender.
5
Loading...