JVC UX-GP5 User Manual

MICRO COMPONENT SYSTEM

UX-GP5

—Consists of CA-UXGP5 and SP-UXG300

Thank you for purchasing a JVC product.

INSTRUCTIONS

Warnings, Cautions and Others Mises en garde, précautions et indications diverses

The lightning flash with arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the products enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

IMPORTANT FOR LASER PRODUCTS

1. CLASS 1 LASER PRODUCT

2. CAUTION: Do not open the top cover or cabinet. There are no user serviceable parts inside the unit; leave all servicing to qualified service personnel.

3. CAUTION: Visible and/or invisible class 1M laser radiation when open. Do not view directly with optical instruments.

4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED INSIDE THE UNIT.

IMPORTANT POUR PRODUITS LASER

1. PRODUIT LASER CLASSE 1

2. ATTENTION: N’ouvrez pas le couvercle supérieur ni le coffret de l’appareil. Il n’y a aucune pièce réparable par l’utilisateur à l’intérieur de l’appareil; confiez toute réparation à un personnel qualifié.

3. ATTENTION: Rayonnement laser visible et/ou invisible de classe 1M une fois ouvert. Ne pas regarder directement dans le faisceau avec des instruments optiques.

4. REPRODUCTION DE L’ÉTIQUETTE: ÉTIQUETTE DE PRÉCAUTION PLACÉE À L’INTERIEUR DE L’APPAREIL.

CAUTION

To reduce the risk of electrical shocks, fire, etc.:

1. Do not remove screws, covers or cabinet.

2. Do not expose this appliance to rain or moisture.

ATTENTION

Afin d’éviter tout risque d’électrocution, d’incendie, etc.:

1. Ne pas enlever les vis ni les panneaux et ne pas ouvrir le coffret de l’appareil.

2. Ne pas exposer l’appareil à la pluie ni à l’humidité.

CAUTION: Proper Ventilation

To avoid risk of electric shock and fire, and to prevent damage, locate the apparatus as follows:

1. Front: No obstructions and open spacing.

2. Sides/Top/Back: No obstructions should be placed in the areas shown by the dimensions below.

3. Bottom: Place on the level surface. Maintain an adequate air path for ventilation by placing on a stand with a height of 10 cm or more.

Front view

Basic and Common Operations

STANDBY lamp

Point at the remote sensor on the front panel. (The operating range is approx. 7 m.)

Turn on or off (standby) the power

Select a source

Adjust the volume

Press

System Remote

Indication/Result

The STANDBY lamp on the System turns off/on.

See “Playing Back a Disc” on page 4 and “Listening to an iPod” on page 5.

Press repeatedly to select “FM” or “AM.”

• For “FM/AM,” see “Listening to FM and AM Broadcasts” on page 5.

See “Listening to Digital Audio Player” on page 5.

Adjustable range: Level 0 (“VOL MIN”) to level 40 (“VOL MAX”).

GVT0242-019B[J/C]

0108WMKMDWJMM

For customer use:

Enter below the Model No. and Serial No. which are located either on the rear, bottom or side of the cabinet. Retain this information for future reference. Model No. Serial No.

For U.S.A.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

Le symbole de l’éclair à l’intérieur d’un triangle équilatéral est destiné à alerter l’utilisateur sur la présence d’une “tension dangereuse” non isolée dans le boîtier du produit. Cette tension est suffisante pour provoquer l’électrocution de personnes. Le point d’exclamation à l’intérieur d’un triangle équilatéral est destiné à alerter l’utilisateur sur la présence d’opérations d’entretien importantes au sujet desquelles des renseignements se trouvent dans le manuel d’instructions.

Note to CATV system installer:

This reminder is provided to call the CATV system installer’s attention to Section 820-40 of the NEC which provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

[European Union only] [Union européenne seulement]

CAUTION:

Changes or modifications not approved by JVC could void the user’s authority to operate the equipment.

For Canada/pour le Canada:

THIS DIGITAL APPARATUS DOES NOT EXCEED THE CLASS B LIMITS FOR RADIO NOISE EMISSIONS FROM DIGITAL APPARATUS AS SET OUT IN THE INTERFERENCE-CAUSING EQUIPMENT STANDARD ENTITLED “DIGITAL APPARATUS,” ICES-003 OF THE DEPARTMENT OF COMMUNICATIONS.

CET APPAREIL NUMERIQUE RESPECTE LES LIMITES DE BRUITS RADIOELECTRIQUES APPLICABLES AUX APPAREILS NUMIRIQUES DE CLASSE B PRESCRITES DANS LA NORME SUR LE MATERIEL BROUILLEUR; “APPAREILS NUMERIQUES”, NMB003 EDICTEE PAR LE MINISTRE DES COMMUNICATIONS.

Caution —

Disconnect the mains plug to shut the power off completely (the STANDBY lamp goes off). When installing the apparatus, ensure that the plug is easily accessible. The (Standby/on) button in any position does not disconnect the mains line.

• When the system is on standby, the STANDBY lamp lights red.

• When the system is turned on, the STANDBY lamp goes off.

The power can be remote controlled.

ATTENTION—Touche

Déconnectez la fiche secteur pour mettre l’appareil complètement hors tension (le témoin STANDBY l s’éteint). Lors de l’installation de l’appareil, assurez-vous que la fiche soit facilement accessible. La touche (attente/sous tension) dans n’importe quelle position ne déconnecte pas l’appareil du secteur.

• Quand l’appareil est en mode d’attente, le témoin STANDBY est allumé en rouge.

• Quand l’appareil est sous tension, le témoin STANDBY s’éteint.

L’alimentation peut être commandée à distance.

(Standby/on) button!

(attente/sous tension)!

Side view

CAUTION:

• Do not block the ventilation openings or holes. (If the ventilation openings or holes are blocked by a newspaper or cloth, etc., the heat may not be able to get out.)

• Do not place any naked flame sources, such as lighted candles, on the apparatus.

• When discarding batteries, environmental problems must be considered and local rules or laws governing the disposal of these batteries must be followed strictly.

• Do not expose this apparatus to rain, moisture, dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.

• Excessive sound pressure from earphones or headphones can cause hearing loss.

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

PHONES jack

How to cancel the demonstration

Press and hold DEMO button while on standby. (Refer to the attached “Information about the demonstration function.”)

Using Headphones

Be sure to turn down the volume before connecting or putting on the headphones.

• Connecting the headphones will deactivate the speakers.

• Sound adjustments also affect the sound through the headphones.

Stereo mini plug cord

NOTE:

DO NOT turn off (standby) the System with the volume set to an extremely high level; otherwise, the sudden blast of sound can damage your hearing, speakers and/or headphones when you turn on the System or start playback.

Drop the volume in a moment

Activate the EALA surround mode —

Emphasize the sound (Sound Turbo function)

Reinforce the bass sound (Active Hyper Bass Pro function) —

Adjust the tone (Bass/Treble)

Change the display brightness

Change the display information (Clock and Source)

Set the Save Mode

—

To restore the volume, press again, or adjust the volume level.

The indicator lights up. To cancel this function, press repeatedly until indicator lights off.

The S.TURBO indicator lights up. To cancel this function, press again.

Press and hold until the AHB indicator lights up.

• When Sound Turbo function is activated (see above), this function cannot be activated.

To cancel this function, press and hold again when Sound Turbo function is deactivated.

Press once for adjusting the bass level; twice for treble level, then, press VOLUME +/–. Adjustable range: –3 to +3.

You can dim the display window and illumination lamp. While the System is turned on...

—

For setting the clock, see “Setting the Clock and Using Timers” on page 6.

Press when the System is on standby. Setting the save mode allows you to reduce power consumption by turning the display off while on

—

standby. To cancel this function, press again when the System is on standby.

Getting Started

Supplied Accessories

After unpacking, check to be sure that you have all the following items.

• Remote control, RM-SUXGP5A (× 1)

• Lithium coin battery CR2025 (× 1) – The battery has been installed when shipped from the

factory.

• AM loop antenna (× 1)

• FM antenna (× 1) If anything is missing, consult your dealer immediately.

Prepare the Remote Control

When you use the remote control for the first time, pull out the insulation sheet.

Insulation sheet

To Replace the Battery in the Remote Control

Lithium coin battery (product number: CR2025)

NOTES:

• Store the battery in a place where children cannot reach. If a child accidentally swallows the battery, consult a doctor immediately.

• To prevent the battery from over-heating, cracking, or starting a fire:

– Do not recharge, short, disassemble or heat the battery or

dispose of it in a fire.

– Do not leave the battery with other metallic materials. – Wrap the battery with tape and insulate when throwing

away or saving it.

– Do not poke the battery with tweezers or similar tools.

• Dispose of battery in the proper manner, according to federal,

state, and local regulations.

• The batteries (battery pack or batteries installed) shall not be exposed to excessive heat source such as sunshine, fire or the like.

For USA-California Only

This product contains a CR Coin Cell Lithium Battery which contains Perchlorate Material – special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate

CAUTION:

Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.

Connections

To connect the FM antenna (supplied)

Extend it so that you can obtain the best reception.

FM antenna (supplied)

For better FM reception

Outdoor FM antenna (not supplied)

Disconnect the supplied FM antenna, and connect to an outdoor FM antenna using a 75 Ω wire with coaxial type connector (IEC or DIN45325).

Rear view

To a wall outlet

Plug the AC power cord only after all connections are complete.

To connect the AM loop antenna (supplied) To assemble the AM loop antenna

Do not connect the AC power cord until all other connections have been made.

AM loop antenna (supplied) Turn it until the best reception is obtained.

NOTES:

• Make sure the antenna conductors do not touch any other terminals, connecting cords and power cord. Also, keep the antennas away from metallic parts of the System, connecting cords, and the AC power cord. This could cause poor reception.

• Make sure both the speakers are connected correctly and firmly.

• When connecting the speaker cords, match the polarity of the speaker terminals: red color to (+) and black color to (–).

• DO NOT connect more than one speaker to each terminal.

• DO NOT allow the conductor of the speaker cords to be in touch with the metallic parts of the System.

To connect the speaker cords

Release

From right speaker

Press and hold

Red

Black

Insert

From left speaker

Playing Back a Disc

The following operations are explained using the remote control, unless mentioned otherwise. However, if the System has the same or similar button names, they can also be used for the operations.

This System can play back... – CD. – CD-R/CD-RW recorded in audio CD format (CD-DA) or recorded MP3/WMA files

in ISO 9660 format.

• When playing back an MP3 or WMA track, MP3 or WMA indicator lights up.

Loading a Disc (on the System only)

Prohibiting Disc Ejection (on the System only)

You can lock the disc tray so that no one can eject the loaded disc.

• This is possible while the System is on standby.

Press to open the disc tray.

• When using an 8 cm disc, place it on the inner circle of the disc tray.

Press to close the disc tray.

To cancel the prohibition, repeat the same procedure.

Basic Disc Operations

To Press Indication/Result

Play back the disc

Stop playback

Select a track

Select a group (MP3/WMA only)

Forward search/ Reverse search

• Current track number and elapsed playing time appear.

For MP3/WMA files: Before current track

number and elapsed playing time appear, the tag information appears if it is recorded.

• During playback, press again to pause.

• While playback is stopped, total track number and total playing time (for MP3/WMA files, group number and track number) appear.

Select the next tracks.

To go back to the beginning of the current or previous tracks.

Select the next groups.

Select the previous groups.

Press and hold to fast-forward the track during playback. To stop searching, release the button.

Press and hold to fast-reverse the track during playback. To stop searching, release the button.

NOTES:

• If no disc is inserted, “NO DISC” appears on the main display.

• If MP3/WMA files are not recorded on the disc, “NO PLAY” appears on the main

display.

Playing Repeatedly—Repeat Play

Press repeatedly to specify the repeat mode as follows:

REP TRK: Repeats the current (or specified) track. [ ] REP GRP: Repeats all tracks in the current group (MP3/WMA

only). [ ]

REP ALL: Repeats all tracks. [ ALL ] REP OFF: Normal playback

Programming the Playing Order—Program Play

1 2

Repeat steps 2 and 3 to program other tracks you want.

• If you try to program a 51st track, “FULL” will appear.

Operations for Program Play (while not playing)

• To check the programmed contents, press 4 or ¢.

• To add tracks, repeat steps 2 and 3 above.

• To erase the last programmed track, press CANCEL.

• To erase the entire program, press and hold CANCEL for about 2 seconds.

• To exit from program play, press MODE. – The stored program is kept.

During stops, press until the PRGM (program) indicator lights up before playing.

• For MP3/WMA files: Select a group number, then a track

number.

• For CD: Select a track number.

Press to program the selected group/track.

The tracks are played back in the programmed order.

Playing at Random—Random Play

1 2

Operations for Random Play

• To skip a track, press ¢.

• To go back to the beginning of the current track, press 4.

• To exit from random play, press MODE while playback is stopped.

RESUME Play (For MP3/WMA only)

When you stop the playback by one of the following operations, this System stores the beginning of the stopped track on the disc. – Pressing 7 once – Changing the source

When you start playback again, playback starts from the stored position. To clear the stored position, open the disc tray.

• When you clear the stored position and start playback, playback starts from the beginning of the first track.

NOTE:

This function does not work in Program Play and Random Play.

Press until the RND (random) indicator lights up before you start playback.

Playback starts in random order. Random Play ends when all tracks are played back.

2 4

Listening to an iPod

The following operations are explained using the remote control, unless mentioned otherwise. However, if the System has the same or similar button names, they can also be used for the operations.

Connecting an iPod

Front view

Open the direct dock for iPod.

Direct dock for iPod

• Be sure to reduce the volume on the System to the minimum level before connecting an iPod. Adjust the volume after starting playback.

• DO NOT connect or disconnect the iPod when the System is turned on.

• You cannot send any data to your iPod from the System.

• Do not carry the System with iPod dock open and iPod is connected. You might drop it or it might cause damages to the iPod dock.

• Do not touch or hit the iPod terminal pins or connector pins in the iPod dock directly. It might cause damages to the connector part.

Insert the iPod directly to the connector pins in the direct dock for iPod.

Connector pins

Basic iPod Operations

To Press Indication/Result

Play back an iPod

Select a track

Change the charge mode (on the System only)

The System detects the iPod and starts playback.

• To turn off the iPod, press and hold for more than 2 seconds.

Select the next tracks.

• Press and hold to fast-forward the track during playback.

To stop searching, release the button.

To go back to the beginning of the current or previous tracks.

• Press and hold to fast-reverse the track during playback.

To stop searching, release the button.

Press and hold while “iPod” is selected as the source. To select the charge mode:

P. ON: The battery in the iPod is charged

through the iPod terminal when “iPod” is selected as the source or during Standby Mode.

P. OFF: The battery is not charged.

Apple iPod (separately purchased))

To Press Indication/Result

Display the menu/ Go back to the previous menu

Select an item on the menu

Play back at random

Play back repeatedly

Turn on iPod’s backlight

—

• The UP/DOWN buttons work in the same way as operating the iPod’s click wheel counterclockwise/clockwise. (Refer to the iPod’s instruction manual for details.)

• Refer to the iPod’s instruction manual for details.

Press and hold for 2 seconds.

Listening to FM and AM Broadcasts

The following operations are explained using the remote control, unless mentioned otherwise. However, if the System has the same or similar button names, they can also be used for the operations.

Basic Tuner Operations

To Press Indication/Result

Select FM or AM

Select a frequency

Tune in to a preset station

Change the FM reception mode (When an FM stereo broadcast is hard to receive)

Press repeatedly.

• The selected frequency band appear.

Press and hold for more than 2 seconds. The System starts searching for stations and stops when a station of sufficient signal strength is tuned in.

• If an FM program is broadcast in stereo, the S (stereo) indicator lights up (only when the reception is good).

• Press during searching to stop.

• Press repeatedly to change the frequency step by step.

Press to select its preset number.

• For presetting stations, see below.

Press to improve reception. The M (mono) indicator lights up. Stereo effect will be lost. To restore the stereo effect, press again.

Presetting Stations

You can preset 30 FM and 15 AM stations manually.

Tune in to a station you want to preset.

• You can also store the FM reception mode.

3 4

Press to activate the preset number entry mode.

• Finish the following steps while the indication on the display is flashing.

Press to select a preset number for the station you want to store.

Press to store the station.

Listening to Digital Audio Player

The following operations are explained using the remote control, unless mentioned otherwise. However, if the System has the same or similar button names, they can also be used for the operations.

Listening to Digital Audio Player

Front view

Digital Audio Player

Stereo mini plug cord (not supplied)

2 3

Turn the volume to minimum.

Press repeatedly to select “AUDIO IN.”

Start playing the Digital Audio Player connected.

Adjust the volume.

To Adjust the Audio Input Level

If the sound from the Digital Audio Player connected to the AUDIO IN jack is too loud or too quiet, you can change the audio input level through the AUDIO IN jack (without changing the volume level).

Press and hold for more than 2 seconds while “AUDIO IN” is selected as the source. You can select one of three levels as follows:

As the number increases, the sound becomes louder.

To audio output (or headphone out, etc.)

Learning More about This System

Basic and Common Operations (see page 3)

• Pressing one of the source buttons also turns on the System and starts playing back if the source is ready or connected.

Playing Back a Disc (see page 4)

• This System cannot play “packet write” discs.

• For MP3/WMA playback...

– In this manual, “file” and “track” are interchangeably used

for MP3/WMA operations. – This System can show the Tag data (Version 1). – MP3/WMA discs are required a longer readout time than

regular CDs. (It depends on the complexity of the group/

file configuration.) – Some MP3/WMA files cannot be played back and will be

skipped. This result from their recording processes and

conditions. – When making MP3/WMA discs, use ISO 9660 Level 1 or

Level 2 for the disc format. – This System can play back MP3/WMA files with the

extension code <.mp3> or <.wma> (regardless of the

letter case—upper/lower). – It is recommended that you make each MP3/WMA file at a

sampling rate of 44.1 kHz and at bit rate of 128 kbps. This

System cannot play back files made at bit rate of less than

64 kbps. – Playback order of MP3/WMA tracks may be different from

the one you have intended while recording. If a folder

does not include MP3/WMA tracks, they are ignored.

• This System can recognize up to 99 groups in a disc. The

total number of groups and tracks (in a disc) that can be recognized by the System is 512 (for MP3/WMA).

Display Information

S.TURBO (Sound Turbo) indicator (See page 3.)

Surround mode indicator (See page 3.)

Play mode indicators (See page 4.)

Main display

File type indicators (See page 4.)

Source indicators (See page 3.)

Playing Back an iPod (see page 5)

• Compatible iPod: – iPod nano 1GB/2GB/4GB – iPod nano (2nd Generation) 2GB/4GB/8GB – iPod nano (3rd Generation) 4GB/8GB – iPod mini 4GB/6GB – iPod (4th Generation) 20GB/40GB – iPod photo (4th Generation) 20GB/30GB/40GB/60GB – iPod video (5th Generation) 30GB/60GB/80GB – iPod touch (1st Generation) 8GB/16GB

• If incompatible iPod type is connected, the iPod may not be

• Sound distortion may occur when playing back audio

Setting the Clock and Using Timers (see page 6)

• You can set the clock and Daily Timer while the Save Mode

• The clock may gain or lose 1 to 2 minutes per month. If this

• When you unplug the AC power cord or if a power failure

Timer Priority:

• If you set the Sleep Timer after Daily Timer starts playing the

operated from the System. To enable the operation, before connecting the iPod, switch the charge mode to “OFF” (see page 5) with “iPod” selected as source.

sources with high recording levels. When distortion occurs, it is recommended to turn off the equalizer of the iPod. For information on operating the iPod, see the iPod instruction manual.

is turned on. While setting the clock or Daily Timer, the display is turning on.

happens, readjust the clock.

occurs, the clock and the timer will be canceled. You need to set the clock first, then the timer again.

selected source, Daily Timer is canceled.

AHB indicator (See page 3.)

Source indicators (See page 3.)

FM reception indicators (See page 5.)

Timer mode indicators (See page 6.)

SLEEP indicator (See page 6.)

A.STBY (Auto Standby) indicator (See page 6.)

Troubleshooting

If you are having a problem with your System, check this list for a possible solution before calling for service.

General

Power does not come on.

\ Power plug is not inserted securely. Plug in securely.

Adjustments or settings are suddenly canceled before you finish.

\ There is a time limit. Repeat the procedure again.

Operations are disabled.

\ The built-in microprocessor may malfunction due to

external electrical interference. Unplug the AC power cord and then plug it back in.

Unable to operate the System from the remote control.

\ The path between the remote control and the remote

sensor on the System is blocked.

\ The batteries are exhausted.

No sound is heard.

\ Speaker connections are incorrect or loose. \ Headphones are connected.

The System does not work properly.

\ Many functions of this System are implemented by

microcomputers. If the System does not work correctly, disconnect the AC power cord from the wall outlet, wait for a while, and connect the cord again.

Disc Operations

The disc does not play.

\ The disc is placed upside down. Place the disc with the

label side up.

\ The disc is recorded with the “packet writing (UDF file

system).” It cannot be played. Check the files you want to play back.

MP3/WMA groups and tracks are not played back as you expect.

\ Playing order is determined when the groups and tracks

were recorded. It depends on the writing application.

The disc sound is discontinuous.

\ The disc is scratched or dirty.

The disc tray does not open or close.

\ The AC power cord is not plugged in. \ Disc ejection is prohibited (see page 4).

iPod Operations

The iPod does not play, but “CONNECT” appears on the display.

\ The iPod battery is low or exhausted. Charge the iPod

battery.

Radio Operations

Hard to listen to broadcasts because of noise.

\ Antennas connections are incorrect or loose. \ The AM loop antenna is too close to the System. \ The FM antenna is not properly extended and

positioned.

\ Electrostatic discharge from your body may cause noise.

If this happens, turn off and on the System again.

Timer Operations

Daily Timer does not work.

\ The System has been turned on when the on-time

comes. Timer starts working only when the System is turned off.

Microsoft and Windows Media are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.

iPod is a trademark of Apple Inc., registered in the U.S. and other countries.

Setting the Clock and Using Timers

The following operations are explained using the remote control, unless mentioned otherwise. However, if the System has the same or similar button names, they can also be used for the operations.

Setting the Clock

Without setting the built-in clock, you cannot use Daily Timer and Sleep Timer.

• “0:00” flashes on the main display until you set the clock.

• To exit from the clock setting, press CLOCK/TIMER as required.

• To go back to the previous step, press CANCEL.

• To check the remaining time until the System shuts off, press once.

Setting the Sleep Timer

When the System is on, press repeatedly to specify the time (in minutes) as follows:

The SLEEP indicator lights up.

Press to activate the clock setting mode.

• If you have already adjusted the clock before, press the button repeatedly until the clock setting mode is selected.

Adjust the hour, then the minute.

5 7

Setting the Daily Timer

Using Daily Timer, you can wake up with your favorite music.

• You can store three Daily Timer settings; however, you can activate only one of the Daily Timers.

• To exit from the timer setting, press CLOCK/TIMER as required.

• To correct a misentry during the process, press CANCEL. You can return to the previous step.

Press repeatedly to select one of the timer setting modes you want to set—DAILY 1 ON time, DAILY 2 ON time, or DAILY 3 ON time—as follows:

1 Adjust the hour then the minute for on-time. 2 Adjust the hour then the minute for off-time. 3 Select the playback source—“TUNER-FM,” “TUNER-AM,”

“DISC,” “AUDIO IN,” or “IPOD.”

4 For “FM/AM”: Select a preset channel. For “DISC”: Select a track. (For MP3/WMA: Select the

group, then the track number.).

For “AUDIO IN”: Make the connected device ready for

playback.

5 Select the volume.

• You can select the volume level (“VOLUME 0” (VOL MIN) to “VOLUME 40” (VOL MAX) and “VOLUME – –”). If you select “VOLUME – –,” the volume is set to the last level when the System is turned off.

Turn off the System (on standby).

• When the on-time comes, the System sets the volume

gradually to the preset level.

To Turn Off the Daily Timer

1 Press repeatedly to select “DAILY 1,” “DAILY 2,” or “DAILY 3.”

To turn on the Daily Timer again, select one of the timer settings by pressing CLOCK/TIMER, then press SET.

Turning Off the System Automatically

—AUTO STANDBY function

Press and hold until the A.STBY indicator lights on the display.

• The A.STBY indicator starts flashing after playback stops. If no operation is done for about 3 minutes, the System turns off.

• Not applicable for FM/AM/AUDIO IN.

To cancel this function, press and hold again.

(only for Disc/iPod)

Precautions

Notes on the power cord

• When you are away on travel or otherwise for an extended period of time, remove the plug from the wall outlet.

• When unplugging the System from the wall outlet, always pull the plug, not the power cord.

• Do not handle the power cord with wet hands.

• Disconnect the power cord before cleaning the System or moving the System.

• Do not alter, twist or pull the power cord, or put anything heavy on it, which may cause fire, electric shock, or other accidents.

• If the cord is damaged, consult a dealer and have the power cord replaced with a new one.

Avoid moisture, water, dust, and high temperatures

• Do not place the System in moist or dusty places.

• If water gets inside the System, turn off the power and remove the plug from the wall outlet, then consult your dealer. Using the System in this state may cause a fire or electrical shock.

• Do not expose the System to direct sunlight or place it near a heating device.

Notes on installation

• Select a place which is level, dry and neither too hot nor too cold—between 5˚C (41˚F) and 35˚C (95˚F).

• Do not install the System in a place subject to vibrations.

• Do not put heavy objects on the System.

To prevent malfunction or damage of the System

• Do not insert any metallic objects, such as wires, hairpins, coins, etc. into the System.

• Do not block the vents.

There are no user-serviceable parts inside. If anything goes wrong, unplug the power cord and consult your dealer.

Maintenance

To get the best performance of the System, keep your discs and mechanism clean.

Handling discs

• Remove the disc from its case by holding it at the edge while pressing the center hole lightly.

• Do not touch the shiny surface of the disc, or bend the disc.

• Put the disc back in its case after use.

• Be careful not to scratch the surface of the disc when placing it back in its case.

• Avoid exposure to direct sunlight, temperature extremes, and moisture.

To clean the disc:

• Wipe the disc with a soft cloth in a straight line from center to edge.

Cleaning the System

• Stains should be wiped off with a soft cloth. If the System is heavily stained, wipe it with a cloth soaked in water-diluted neutral detergent and wrung well, then wipe clean with a dry cloth.

• Since the System may deteriorate in quality, become damaged or get its paint peeled off, be careful about the following:

– DO NOT wipe it hard. – DO NOT wipe it with thinner or benzine. – DO NOT apply any volatile substance such as insecticides to it. – DO NOT allow any rubber or plastic to remain in contact for a long time.

Specifications

Amplifier section

OUTPUT POWER:

35 W per channel, min. RMS, driven into 4 Ω at 1 kHz with no more than 10% total harmonic distortion

Speakers/Impedance: 4 Ω – 16 Ω Audio input AUDIO IN: 500 mV/50 kΩ (at “IN LVL1”) 250 mV/50 kΩ (at “IN LVL2”) 125 mV/50 kΩ (at “IN LVL3”) Digital input: iPod

Tuner section

FM tuning range: 87.5 MHz - 108.0 MHz AM (MW) tuning range: 530 kHz - 1 710 kHz

CD player section

Dynamic range: 88 dB Signal-to-noise ratio: 85 dB Wow and flutter: Immeasurable

iPod section

iPod output power: DC 5 V 500 mA

Speakers

Speaker units: 10 cm (3-15/16 inches) cone x 1 Impedance: 4 Ω Dimensions (W x H x D) 160 mm x 250 mm x 150 mm (approx.): (6-5/16 inches x 9-7/8 inches x

5-15/16 inches)

Mass (approx.): 1.6 kg (3.6 lbs) each

General

Power requirements: AC 120 V , 60 Hz Power consumption: 20 W (power on)

3.5 W (standby mode) 1 W or less (Save Mode) Dimensions (W x H x D): 165 mm x 251 mm x 255 mm (6-1/2 inches x 9-15/16 inches x

10-1/16 inches)

Mass: 2.6 kg (5.8 lbs)

Specifications and appearance are subject to change without prior notice.

BT-51018-5 (0306)

6 8

+ 2 hidden pages