Lead free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade)
Lead free solder used in the board (material : Sn-Cu, melting point : 230 Centigrade)
SUBWOOFER OUT 500 mV/10 kΩ
Digital output OPTICAL DIGITAL OUT -21 dBm to -15 dBm (660 nm ±30 nm)
Digital input USB MEMORY REC/PLAY
AV (SCART) Color system PAL (interlaced/progressive)
Composite video 1 V(p-p)/75 Ω
S-VIDEO Y (luminance)1 V(p-p)/75 Ω
C (chrominance, burst) 0.3 V(p-p)/75 Ω
RGB 0.7 V(p-p)/75 Ω
VIDEO OUT
(COMPONENT)
Speaker impedance 6 Ω - 16 Ω
FM tuning range 87.50 MHz - 108.00 MHz
AM (MW) tuning range 522 kHz - 1 629 kHz
• +R/+RW (DV D Video/MP3/WMA/WAV/JPEG/MPEG-1/MPEG-2/DivX format)
• DVD-ROM (MP3/WMA/WAV format)
Dynamic range 80 dB
Horizontal resolution 500 lines
Wow and flutter Immeasurable
USB section
Playable files MP3/WMA/WAV/JPEG/MPEG-1/MPEG-2/DivX format
USB specification Compatible with USB 2.0 Full Speed
Compatible device Mass storage class
Compatible system FAT16, FAT32
Bus power supply DC 5 V=500 mA
General
Power requirements AC 230 V~, 50 Hz
Power consumption 155 W (at operation)
18 W (at standby)
1 W or less (at ECO mode)
Dimensions (approx.) 166 mm × 252 mm × 304 mm (W/H/D)
Mass (approx.) 5.4 kg
Ø 3.5 mm)
1-2 (No.MB682<Rev.001>)
Page 3
Speakers - SP-UXG950V
Speaker units Tweeter 4 cm cone x 1
Woofer 12 cm cone x 1
Impedance 6 Ω
Dimensions (approx.) 160 mm × 250 mm × 179 mm (W/H/D)
Mass (approx.) 2.2 kg each
Specifications and appearance are subject to change without prior notice.
UX-G650
Amplifier section
OUTPUT POWER 120 W (60 W + 60 W) at 6 Ω (10% THD)
Speakers/Impedance 6 Ω - 16 Ω
Audio inputAUDIO IN 500 mV/47 kΩ (at “IN LVL1”)
FM tuning range 87.50 MHz - 108.00 MHz
AM (MW) tuning range 522 kHz - 1629 kHz
Disc player section
Dynamic range 88 dB
Signal-to-noise ratio 85 dB
Wow and flutter Immeasurable
USB storage
USB specification Compatible with USB 2.0 Full Speed
Compatible device Mass storage class
Compatible file system FAT16, FAT32
Bus power supply Max. 500 mA
Speakers
Speaker units 4 cm cone x 1
12 cm cone x 1
Impedance
Dimensions (approx.) 160 mm x 250 mm x 179 mm (W/H/D)
Mass (approx.) 2.2 kg each
General
Power requirements AC 230 V~, 50 Hz
Power supply to USB mass storage class device DC 5 V=500 mA
Power consumption 130 W (power on)
16 W (standby mode)
1 W or less (EC O Mode)
Dimensions (W x H x D) 166 mm x 252 mm x 304 mm
Mass 4.9 kg
Specifications and appearance are subject to change without prior notice.
(No.MB682<Rev.001>)1-3
Page 4
SECTION 1
PRECAUTION
1.1Safety Precautions
(1) This design of this product contains special hardware and
many circuits an d compo nents spec ially f or saf ety purpos es. For continued protection, no changes should be made
to the original design unless authorized in writing by the
manufacturer. Replacement parts must be identical to
those used in the original circuits. Services should be performed by qualified personnel only.
(2) Alterations of the design or circuitry of the product should
not be made. Any design alterations of the product should
not be made. Any design alterations or additions will void
the manufacturers warranty and will further relieve the
manufacture of respons ibility for p ersonal injury or p roperty
damage resulting therefro m.
(3) Many electrical and mechanical parts in the products have
special safety-related characteristics. These characteristics are often not eviden t from visu al inspec tion nor ca n the
protection afforded by the m necessaril y be obtained by using replacement compo nents rated for higher vo ltage, wattage, etc. Replacement parts which have these special
safety characteristics are identified in the Parts Lis t of Se rvice Manual. Electrical components having such features
are identified by shadin g on the schema tics and by ( ) on
the Parts List in the Servic e Manual. The use of a s ubstitute
replacement whic h d oe s not ha ve the same safety c ha rac teristics as the recommended replacement parts shown in
the Parts List of Service Manual may create shock, fire, or
other hazards.
(4) The leads in the products are routed and dressed with ties,
clamps, tubings, barri ers and the l ik e to b e se para ted from
live parts, high temperature parts, moving parts and/or
sharp edges for the prevention of electric shock and fire
hazard. When service is required, the original lead routing
and dress should be observed, and it should be confirmed
that they have been returned to normal, after reassembling.
(5) Leakage shock hazard testing
After reassembling the product, always perform an isolation check on the exposed metal parts of the product (antenna terminals, knobs, metal cabinet, screw heads,
headphone jack, co ntrol shaf ts, etc.) to be sure t he prod uct
is safe to operate w ithou t dange r of el ectric al sh ock.Do not
use a line isolation transformer during this check.
• Plug the AC line cord directly into the AC outlet. Using a
"Leakage Current Tes t er" , me as ure t he l eak ag e current
from each exposed metal pa rts of the cabine t, particula rly any exposed metal part having a return path to the
chassis, to a know n good earth ground. Any le akage current must not exceed 0.5mA AC (r.m.s.).
• Alternate check method
Plug the AC line cord directly into the AC outlet. Use an
AC voltmeter having, 1,000Ω per volt or more sensitivity
in the following mann er. C o nne ct a 1,50 0Ω 10W resistor
paralleled by a 0.15µF AC-type capacitor betw een an exposed metal part and a known good earth ground.
Measure the AC voltage across the resistor with the AC
voltmeter.
Move the resistor connection to each exposed metal
part, particularly any exposed metal part having a return
path to the chassis, and measure the AC voltage across
the resistor. Now, reverse the plug in the AC outlet and
repeat each measurement. Voltage measured any must
not exceed 0.75 V AC (r.m.s.). This corresponds to 0.5
mA AC (r.m.s.).
AC VOLTMETER
(Having 1000
ohms/volts,
or more sensitivity)
0.15 F AC TYPE
Place this
probe on
1500 10W
Good earth ground
1.2Warning
(1) This equipment has been designed and manufactured to
meet international safety standards.
(2) It is the legal responsibility of the repairer to ensure that
these safety standards are maintained.
(3) Repairs must be made in accordance with the relevant
safety standards.
(4) It is essen tial that sa fety critic al com ponen ts ar e repl aced
by approved parts.
(5) If mains voltage selector is pro vided, ch eck set ting for loc al
voltage.
1.3Caution
Burrs formed during molding ma y be left over on some parts
of the chassis.
Therefore, pay attention to such burrs in the case of preforming repair of this system.
1.4Critical parts for safety
In regard with component parts appearing on the silk-screen
printed side (parts side) of the PWB di agra ms , the parts that are
printed over with black such as the resistor ( ), diode ( )
and ICP ( ) or identified by the " " mark nearby are critical
for safety. When replacing them, be sure to use the parts of the
same type and rating as specified by the manufacturer.
(This regulation dose not Except the J and C version)
each exposed
metal part.
1-4 (No.MB682<Rev.001>)
Page 5
1.5Preventing static electricity
Electrostatic discharge (ESD), w hi ch occurs w hen sta tic ele ct ricit y sto red i n the bod y, fa bric , etc. is discharged, ca n de stroy the laser
diode in the traverse unit (optical pickup). Take care to prevent this when performing repairs.
1.5.1 Grounding to prevent damage by static electricity
Static electricity in the work area can destroy the optical pickup (laser diode) in devices such as laser products.
Be careful to use proper grounding in the area where repairs are being performed.
(1) Ground the workbench
Ground the workbench by laying conductive material (such as a conductive sheet) or an iron plate over it before placing the
traverse unit (optical pickup) on it.
(2) Ground yourself
Use an anti-static wrist strap to release any static electricity built up in your body.
(caption)
Anti-static wrist strap
1M
Conductive material
(conductive sheet) or iron palate
(3) Handling the optical pickup
• In order to maintain quality during transport and before installation, both sides of the laser diode on the replacement optical
pickup are shorted. After replacement, return the shorted parts to their original condition.
(Refer to the text.)
• Do not use a tester to che ck the con dition of th e laser dio de in the opt ical pick up. The tes ter's inte rnal power so urce can ea sily
destroy the laser diode.
1.6Handling the traverse unit (optical pickup)
(1) Do not subject the traverse unit (optical pickup) to strong shocks, as it is a sensitive, complex unit.
(2) Cut off the shorted part of the flexible cable using nip pers, etc. afte r replacing th e optical pi ckup. For speci fic details, refe r to the
replacement procedure in th e t ext . R em ove the anti-static pin w he n re pla cing the traverse unit. Be c arefu l not to tak e to o l on g a
time when attaching it to the connector .
(3) Handle the flexible cable carefully as it may break when subjected to strong force.
(4) I t is not possible to adjust the semi-fixed resistor that adjusts the laser power. Do not turn it.
1.7Attention when traverse unit is decomposed
*Please refer to "Disassembly method" in the text for the pickup unit.
• Apply solder to the short land sections before the card wire is disconnected from the connecto on the servo board. (If the card wire
is disconnected without applying solder, the pickup may be destroyed by static electricity.)
• In the assembly, be sure to remove solder from the short land sections after connecting the card wire.
Solder short land section
(No.MB682<Rev.001>)1-5
Page 6
1.8Important for laser products
1.CLASS 1 LASER PRODUCT
2.CAUTION :
(For U.S.A.) Visible and/or invisible class II laser radiation
when open. Do not stare into beam.
(Others) Visible and/or invisible class 1M laser radiation
when open. Do not view directly with optical instruments.
3.CAUTION : Visible and/or invisible laser radiation when
open and inter lock failed or defeated. Avoid direct
exposure to beam.
4.CAUTION : This laser product uses visible and/or invisible
laser radiation and is equipped with safety switches which
prevent emission of radiation when the drawer is open and
the safety interlocks have failed or are defeated. It is
dangerous to defeat the safety switches.
5.CAUTION : If safety switches malfunction, the laser is able
to function.
6.CAUTION : Use of controls, adjustments or performance of
procedures other than those specified here in may result in
hazardous radiation exposure.
!
Please use enough caution not to
see the beam directly or touch it
in case of an adjustment or operation
check.
REPRODUCTION AND POSITION OF LABELS and PRINT
WARNING LABEL and PRINT
1-6 (No.MB682<Rev.001>)
Page 7
SECTION 2
SPECIFIC SERVICE INSTRUCTIONS
This service manual does not describe SPECIFIC SERVICE INSTRUCTIONS.
SECTION 3
DISASSEMBLY
3.1Main body (Used figure are UX-G950VE)
3.1.1 Removing the Metal cover (See Fig.1, 2)
(1) Remove the two screws A attaching the Heat sink cover.
(See Fig.1)
(2) Remove the five screws B attaching the Metal cover. (See
Fig.1)
(3) Remove the two screws C attaching the both side of Metal
cover. (See Fig.2)
B
B
B
A
B
B
Fig.1
C
Fig.2
(No.MB682<Rev.001>)1-7
Page 8
3.1.2 Removing the Front panel (see Fig.3 to 5)
(1) Disconnect the card wire from Front panel connected to
connector CN330
(2) Remove the two screws D attaching the both side of Front
panel. (See Fig.4)
(3) Disengage two hooks a engaged Front panel. (See Fig.4)
(4) Remove the two screws E attaching the Front panel. (See
Fig.5)
(5) Disengage one hook b engaged Front panel. (See Fig.5)
of the Micom board. (See fig.3)
D
CN330
Fig.3
3.1.3 Removing the Tuner pack (See Fig.6, 7)
(1) Disconnect the card wire from Tuner pack connected to
connector CN338
(2) Remove the two screws F attaching the Tuner pack. (See
Fig.7)
CN338
of the Micom board. (See Fig.6)
hook
a
Fig.4
EE
hook
Fig.5
b
Fig.6
1-8 (No.MB682<Rev.001>)
F
Fig.7
Page 9
3.1.4 Removing the Amp board (See Fig.8 to 10)
(1) Disconnect the Connector wire from Front jack board con-
nected to connector CN201
(2) Disconnect the card wire from Micom board connected to
connector CN204
(3) Disconnect the flat wires connected to connectors CN207
and CN208 of the Amp board. (See Fig.8)
(4) Disconnect the card wire from Micom board connected to
connector CN205
(5) Disconnect the card wire from DVD me chani sm c onnec ted
to connector CN213
(6) Disconnect the flat wire from Front jack board co nnected to
connector CN203 of the Amp board. (See Fig.8)
(7) Disconnect the connector wire from Power transformer
connected to connector CN209
Fig.8)
(8) Disconnect the flat wire s from Power board connected to
connectors CN210
(See Fig.8)
(9) Disconnect the connector wir e from FA N connected to con-
nector CN206
(10) Remove the two screws G attaching the Amp board. (See
Fig.8)
(11) Remove the two screws H attaching the H eat sink bra cket.
(See Fig.9)
(12) Remove the one screw J attaching the Amp board. (See
Fig.9)
(13) Remove the two screws K attaching the Speaker terminal.
(See Fig.10)
of the Amp board. (See Fig.8)
of the Amp board. (See Fig.8)
, CN211 and CN212 of the Amp board.
of the Amp board. (See Fig.8)
CN204CN203
of the Amp bo ard. (See F ig.8)
of the Amp board. (See Fig.8)
of the Amp board. (See
H
J
Fig.9
CN201
CN213
GG
CN209
CN212
CN208
CN207
CN205
Fig.8
CN211
CN210
CN206
K
Fig.10
(No.MB682<Rev.001>)1-9
Page 10
3.1.5 Removing the Rear panel (See Fig.11)
(1) Remove the seven screws L attaching the Rear panel.
3.1.6 Removing the DVD mechanism (See Fig.12, 13)
(1) Disconnect the connector wire from Front jack board con-
nected to connect or CN811
Fig.12)
(2) Disconnect the card wires connected to connectors
, CN353 and CN361 of the Micom board. (See
CN345
Fig.13)
of the Front end board. (See
L
L
Fig.11
CN811
Fig.12
Fig.13
CN345
CN353
CN361
1-10 (No.MB682<Rev.001>)
Page 11
3.1.7 Removing the Micom board (See Fig.14)
(1) Remove the two screws M attaching the Micom board.
3.1.8 Removing the Front jack board (See Fig.15)
(1) Remove the three screws N attaching the Front jack board.
3.1.9 Removing the Power board (See Fig.16)
(1) Disconnect the connector wires from Power transformer
connected to connect ors CN800
Power board.
(2) Remove the two screws P attaching the power board.
, CN804 and CN805 of the
M
Fig.14
N
Fig.15
CN805CN804
3.1.10 Removing the FL board (See Fig.17)
(1) Disengage four hooks c engaged FL board.
CN800
Fig.16
hook
hook
Fig.17
P
c
c
(No.MB682<Rev.001>)1-11
Page 12
3.1.11 Removing the Function board (See Fig.18)
(1) Remove the Volume knob.
(2) Remove the nine screws Q attaching the Function board.
Q
Q
Fig.18
1-12 (No.MB682<Rev.001>)
Page 13
3.2DVD mechanism
3.2.1 Removing the traverse mechanism
(See Fig.1 to 6)
(1) Remove the two screws A attaching the tr amecha ho lder
from top side of DVD mechanism assembly. (See Fig.1)
(2) Remove the two screws B attaching the DVD module
board. (See Fig.2)
(3) Remove the four screws C attaching the CB holder and
take out it. (See Fig.3)
(4) Remove the four screws D attaching the traverse mecha-
nism. (See Fig.4)
(5) Solder the solder part of DVD pick up. (See Fig.5)
(6) Disconnect the card wire from CN101
DVD module board. (See Fig. 6)
Caution:
• Solder the short land section on the DVD pickup before dis-
connecting the card wire from the connector on the DVD
pickup. If the card wire i s disconnected w ithout attaching solders, the pickup may be destroyed by static electricity.
• When attaching the DVD pickup, be sure to remove solders
from the short land section after connecting the card wire to
the connector on the DVD pickup.
and CN201 on the
A
Clamper base
B
A
DVD mechanism assembly
Fig.1
DVD mechanism assembly
B
DVD module board
Fig.2
(No.MB682<Rev.001>)1-13
Page 14
DVD module board
Solder short land section
Fig.5
C
C
CC
Fig.3
DVD mechanism assembly
Traverse mechanism assembly
DVD module board
CN101
CN201
Fig.6
DD
Fig.4
1-14 (No.MB682<Rev.001>)
Page 15
3.2.2 Removing the pickup assembly
(See Fig.7 to 11)
(1) Remove the two rod springs pressing the guide s haft. (See
Fig.7)
(2) Remove the screw E and F attaching the spring holde r.
(See Fig.8)
(3) Remove the read screw from traverse mechanism assem-
bly. (See Fig.9)
Caution:
When remove the lead screw, do not loss the middle
gear. (See Fig.10 and 11)
(4) Remove the bar spring pressing the shaft. (See Fig.10)
(5) Take out the pickup assembly from traverse mechanism
chassis by order. (See Fig.11)
(SHAFT)
(T.TABLE)
HOOK
(BAR SPRING)
Fig.10
ROD SPRINGROD SPRING
Fig.7
Spring holder
Fig.8
order 2
order 3
order 1
Fig.11
EF
Middle gear
Lead screw
Fig.9
(No.MB682<Rev.001>)1-15
Page 16
3.2.3 Removing the feed motor assembly
(See Fig.12)
(1) Remove the one screw G attaching the feed motor assem -
bly.
(2) Remove the feed motor wires from solder part of spindle
motor board.
Solder part
3.2.4 Removing the spindle motor assembly
(See Fig.13)
(1) Remove the three screws H attaching the spindle motor
from spindle motor board.
Middle gear
Lead screw
Fig.12
H
Spindle motor
Fig.13
G
1-16 (No.MB682<Rev.001>)
Page 17
3.2.5 Removing the tray assembly
(See Fig.14 & 15)
(1) Remove the two screws J attaching the clamper base.
(See Fig.14)
(2) Remove the one screw K attaching the shaft guide from
bottom side. (See Fig.14)
(3) Remove the two screws L attaching the shaft guide from
top side. (See Fig.15)
Caution:
When attach the tray assem bly, boss of lo ading su b asse mbly
should atta ch to guide of bottom si de at tray as sembly. (Se e
Fig.15)
J
order 1
order 2
clamper base
L
K
Fig.15
[bottom side]
Fig.14
(No.MB682<Rev.001>)1-17
Page 18
SECTION 4
ADJUSTMENT
4.1ATTENTION IN SERVICE OF DVD SECTION
(1) When pickup, Flash ROM ,DVD module board were changed, initialize EEPROM by all means.
(2) When full initialization was excuted, excute learning with a DVD test disc by all means.
Test disc : VT-501, VT-502
Learning m ethod : It is adjusted automatically by normal playback of a DVD disc.
4.2DVD/CD TEST MODE
CAUTION:
The operation please use the button of the main body.
(1) Press "DVD/CD" key + "STOP" key on panel, then AC in.
(2) FL display "T **# $&"
** is Destination
# is Region Code
$ is Learning Condition
& is Initialize Condition
(3) Press " MENU/PL " key repeatedl y, until FL display " CHECK"
(4) Press number key on Remote Control "1-10, 0 and >=10"
Key 1 : "PLAYBACK"
Key 2 : "WOBBLE"
Key 3 : "TNO-1 SR"
Key 4 : "CDLD LSR"
Key 5 : "DVDLDLSR"
Key 6 : " JITX1 "
Key 7 : "EEP BWD"
Key 8 : "EEP FWD"
Key 9 : " TEMP "
Key 10 : " DVD-DL "
Key 0 : " MONITOR "
Key >=10 : " INIT "
1-18 (No.MB682<Rev.001>)
Page 19
4.3SYSTEM MICOM TEST MODE
CAUTION:
The operation please use the button of the remote controller.
Total DVD/CD mode play time by Hour:Minutes ->
Mecha temperature data ->
Spk level detect over trigger level by percentage, % ->
Volume level drop, 1, 2 then 3, each -2db ->
Fan level detect over trigger level by percentage, % and on(1)/off(0) ->
Volume level to max by compulsion
Refer SYSCOM TEST
FL all display
SECTION 5
This service manual does not describe TROUBLESHOOTING.
(No.MB682<Rev.001>)1-19
Page 20
Victor Company of Japan, Limited
Audio/Video Systems Division 10-1, 1cho me ,Oh w ata ri-m ach i,Ma eba shi - city,3 71- 85 43,J apa n
(No.MB682<Rev.001>)
Printed in Japan
VPT
Page 21
PARTS LIST
UX-G950VB,UX-G950VE,UX-G950VEN
UX-G950VEV,UX-G950VEE,UX-G650B
UX-G650E,UX-G650EN,UX-G650EV
* All printed circuit boards and its assemblies are not available as service parts.
- Contents -
Exploded view of general assembly and parts list (Block No.M1)
DVD mechanism assembly and parts list (Block No.MJ)
DVD loading base assembly and parts list (Block No.MN)
Electrical parts list (Block No.01~04)
Packing materials and accessories parts list (Block No.M3)
MB682PAR<Rev.001>
3- 2
3- 6
3- 8
3-10
3-18
3-1
Page 22
Exploded view of general assembly and parts list
e
w
Block No.
49
49
50
51
FL board
9
K
9
51
Mic & Switch board
11
M
1
Power amplifier
board
59
j
11
64
M
M
57
Only
UX-G650
series
z
46
d
u
32
33
g
x
h
e
a
53
Primary board
20
Jack board
d
m
c
s
4
Only
UX-G950V
series
1
27
3
G
7
10
Only
UX-G950V
series
8
11
15
27
6
5
48
2
48
Only
2
UX-G950VB
E,EN,EV
ver
14
15
Jack board
19
3-2
Page 23
f
29
49
D
28
A
28
B
Only
UX-G650
series
A
32
33
w
r
g
z
ier
46
d
a
u
Primary board
x
h
e
c
g
h
e
20
31
m
71
k
37
58
p
F
46
52
n
40
D
45
42
44
F
43
a
62
56
73
67
Jack board
c
s
68
18
m
66
17
16
17
s
k
z
n
35
41
34
r
36
63
y
39
b
26
Except
UX-G950VEE
74
38
B
23
25
24
70
24
G
30
47
25
j
55
Only
UX-G950V
series
q
f
61
60
22
q
Micom board
y
p
f
w
x
b
u
12
13
19
K
13
19
21
The parts without symbol number are not service.
3-3
Page 24
General Assembly
Block No. [M][1][M][M]
Symbol No.Part No.Part NameDescriptionLocal
1GV10423-002AFRONT PANEL950VB,950VE,950VEN,950VEV,950VEE
1GV10423-001AFRONT PANEL650B,650E,650EN,650EV
2GV40313-002AFELT SPACER(x2)
3GV20511-002AFRONT LE NS95 0VB,950VE,950VEN,950VEV,950VEE
3GV20511-001AFRONT LENS650B,650E,650EN,650EV
4GV20518-001AVOL.ORNAMENT B950VB,950VE,950VEN,950VEV,950VEE
4GV20515-00 1 AVOL.O RN A ME N T A650B,650E,650EN,650EV
5GV20512-002AFRONT COVER A950VB,950VE,950VEN,950VEV,950VEE
5GV20512-001AFRONT COVER650B,650E,650EN,650EV
6GV31187-001AILLUM.LENS950VB,950VE,950VEN,950VEV,950VEE
7GV20513-003AFUNCTION BUTTON950VB,950VE,950VEN,950VEV,950VEE
7GV20513-001AFUNCTION BUTTON650B,650E,650EN,650EV
8GV31188-002AEJECT BUT950VB,950VE,950VEN,950VEV,950VEE
8GV31188-001AEJECT BUT650B,650E,650EN,650EV
9GV30349-095ASPACER(x2)
10GV40557- 001ALED HOLDER950VB,9 50VE,950V EN,950VEV,950VEE
11QYSDSF2608ZATAP SCREWM2.6 x 8mm(x9)
12GV10424- 001ABOTTOM CHASSIS
13GV40313- 002AFELT SPACER(x2)
14GV40840-001ASHEILD950VB,950VE,950VEN,950 VEV
15QYSDSG3006EATAP SCREWM3 x 6mm(x4)
68QMF51W 2- 2R0-J8FUS E2A AC250V
70QYSDSG3008ZATAP SCREWM3 x 8mm
71QYSDSG3008ZATAP SCREWM3 x 8mm
73WJN0253-001A-EFPC CONNE
74QQR1835 -0 01NOISE FILTER950VB, 950VE,950VEN, 95 0VEV,650B,650E,650EN,650 EV
3-5
Page 26
DVD mechanism assembly and parts list
Grease
=JVG-31N
=JVS-1003
=1401C
FXL-D10-1M
Block No.
16
M
J
17
M
M
< Back side >
29
28
31
25
24
7.0mm
+
0.2mm
-
31
3
30
26
27
10
18
20
30
31
31
10
9
3
23
22
7
6
13
11
15
14
21
5
4
8
2
1
3-6
12
The parts without symbol number are not service.
Page 27
DVD mechanism
Symbol No.Part No.Part NameDescriptionLocal
1LV22234-003AT.M.CHASSIS
2LV22235-002ASPINDLE BASE
3QYSDST2005ZATAP SCREWM2 x 5mm(x2)
4LV36555-001AG.S.HOLDER
5QYSDST2005ZATAP SCREWM2 x 5mm
6LV4 4041-002AGUIDE SHAFT
7LV4 4479-001ABAR SPRING
8LV22236-001AFEED HOLDER
9QAR0165-001FEED MOTOR5 . 0V DC
10LV30225-0X5ASPACER(x2)
11LV36557-001AF.M.GEAR
12QYSPSPT2030MASCREWM2 x 3mm
13QYSDST20 05ZATAP SCREWM2 x 5mm
14QAL0786- 006PIC K U P
14orQ AL0786-004P.UP
15LV22237-001ARACK ARM
16LV36560-001ARACK ARM SPRING
17QYSPSFU1740ZATAP SCREWM1.7 x 4mm(x2)
18QUQK05-2415AC-EFFC WIRE24pin 15cm
20LV44041-002AGUIDE SHAFT
21LV36559-001AL.S.GEAR
22LV41517-003ALEAD SCREW
23LV36558-001AMIDDLE GEAR
24LV36556-001ASPRING HOLDER
25LV44623-001ACOMP.SPRING
26QYSDST20 05ZATAP SCREWM2 x 5mm
27QYSDST26 16MATAP SCREWM2.6 x 16mm
28QAR0386-001S.MOTOR
29QYSPSPU1775ZASCREWM1.7 x 7.5mm(x3)
30LV44042-001AROD SPRING(x2)
31LV44046-001AADJUST SCREW(x4)
Block No. [M][J][M][M]
3-7
Page 28
DVD loading base assembly and parts list
FMU-MB6-71M
Grease
JVS-1003
CFD-4007ZY2
15
h
18
19
17
26
2
14
Block No.
3
11
13
11
MMMN
1
h
< Back side >
25
A
B
24
24
DVD module board
15
j
16
10
9
7.75mm
0.10mm
4
7
8
6
k
e
Back side
5
f
25
c
j
d
12
22
24
24
23
22
21
c
3-8
22
21
B
A
21
22
DVD loading
switch board
21
f
20
e
d
The parts without symbol number are not service.
Page 29
DVD loading base assembly
Symbol No.Part No.Part NameDescriptionLocal
1LV11065-014ALOAD ER SUB ASSY
2E407140-001SSC.D ROLLER
3E407149-001SSRUBBER TUB E
4LV10979-003ATRAY
5LV35499-003ASHAFT GUIDE
6LV44022-001ASHAFT
7QYSSSF2008ZATAP SCREWM2 x 8mm
8QYSDSF2008ZATAP SCREWM2 x 8mm(x2)
9QAR0197-001MOTOR2. 0V DC
9orQ AR0450-001MOTOR
10LV43844-002AMOTOR PULLEY
11QYSPSPU1730ZASCREWM 1 . 7 x 3 mm ( x2)
12QYSDSF20 08ZATAP SCREWM2 x 8mm
13LV43974-001ABELT
14LV21852-003ACLAMPER BASE
15QYSDSF20 08ZATAP SCREWM2 x 8mm(x2)
16LV35056-002ADVD CLAMPER
17LV42930-003AMAGNET
17orLV41118-003AMAGNET
18LV43848-001AYOKE
19LE40906-002A-MSPEC I AL SCREW
20------------SINGLE DVD TRAM
21LV44043-001AINSULATOR(x4)
22LV44044-001ASPECIAL SCREW(x4)
23LV11212-003ACB HOLDER
24QYSBSF2608ZATAP SCREWM2.6 x 8mm( x4 )
25LV44209-001AWASHER SCREW(x2)
26LV44603-003ALASER CAUTION
IC291KIA278R09PIIC
IC300------------MICON IC
IC320BD9778F-XIC
IC330GP1FAV30TK0FOPT TRANSMITTER950VB,950V
IC351RT3Y97M-XTR ARRAY950VB,950V
IC401MM1623XF-XIC950VB,950V
IC901LB1641IC
Q1000KRC102S-XDIGI TRANSI STOR
Q1001KRC102S-XDIGI TRANSI STOR
Q2002RT3Y97M-XTR ARRAY
Q2011KTC3875/YG/-XTRANSISTOR
Q2012KTA1504/YG/-XTRANSISTOR
Q2013KTC3200/G L/-TTRANSISTOR
Q2101KTA1268/GL/-TTRANSISTOR
Q2201KTA1268/GL/-TTRANSISTOR
Q2511RT3X99M-XTRANSISTOR
Q2701KRA102S-XDIGI TRANSISTOR
Q2711RT3X99M-XTRANSISTOR
Q2721RT3X99M-XTRANSISTOR
Q2751KRC110S-XDIGI TRANSI STOR
Q2801KTA1504/YG/-XTRANSISTOR
Q2802KRC111S-XTRANS ISTOR
Q3200KRC102S-XDIGI TRANSI STOR
Q3250KRC111S-XTRANS ISTOR
Q3301KRC110S-XDIGI TRANSI STOR
Q3510KTC3875/YG/-XTRANSISTOR950VB,950V
Q3710KTA1046/Y/TRANSISTOR
Q3720KTC3875/YG/-XTRANSISTOR
Q3730KRA102S-XDIGI TRANSISTOR
Q3731KRC102S-XDIGI TRANSI STOR
Q4300KRC102S-XDIGI TRA N SI STOR950VB,950V
C2204NDC31HJ-5R0XC CAPACITOR5pF 50V J
C2205NCB31HK-104XC CAPACITOR0.1uF 50V K
C2206NCB31HK-104XC CAPACITOR0.1uF 50V K
C2207NRSA63J-102XMG RESISTOR1k
C2208QETN1JM-476ZE CAPACITOR47uF 63V M
C2301QETN1HM-475ZE CAPACITOR4.7uF 50V M
C2303QEZ 0863-106ZM C APACITOR1 0u F
C2304QETN1HM-475ZE CAPACITOR4.7uF 50V M
C2305QETN1HM-475ZE CAPACITOR4.7uF 50V M950VB,950V
C2308QFN C 2AJ-822ZM CAPACITOR8200pF 100V J
C2309QFN C 2AJ-104ZM CAPACITOR0.1uF 100V J
C2310QFN C 2AJ-104ZM CAPACITOR0.1uF 100V J
C2311QFN C 2AJ-472ZM CAPACITOR4700pF 100V J
C2312QEZ 0863-106ZM C APACITOR1 0u F
C2313QTE2A60-475ZE CAPACITOR4.7uF 100V
C2314QET N 1 JM -107ZE CAPACITOR100uF 63V M
C2401QETN1HM-475ZE CAPACITOR4.7uF 50V M
C2403QEZ 0863-106ZM C APACITOR1 0u F
C2404QETN1HM-475ZE CAPACITOR4.7uF 50V M
C2405QETN1HM-475ZE CAPACITOR4.7uF 50V M950VB,950V
C2408QFN C 2AJ-822ZM CAPACITOR8200pF 100V J
C2409QFN C 2AJ-104ZM CAPACITOR0.1uF 100V J
C2410QFN C 2AJ-104ZM CAPACITOR0.1uF 100V J
C2411QFN C 2AJ-472ZM CAPACITOR4700pF 100V J
C2412QEZ 0863-106ZM C APACITOR1 0u F
C2501QETN1HM-106ZE CAPACITOR10uF 50V M
C2502QETN1HM-475ZE CAPACITOR4.7uF 50V M
C2503QETN1HM-105ZE CAPACITOR1uF 50V M
C2504NCB31CK-154XC CAPACITOR0.15uF 16V K
C2511QEZ0863-226ZE CAPACITOR22uF
C2512QFN C 2AJ-104ZM CAPACITOR0.1uF 100V J
C2513QFN C 2AJ-104ZM CAPACITOR0.1uF 100V J
C2521QEZ0863-226ZE CAPACITOR22uF
C2522QFN C 2AJ-104ZM CAPACITOR0.1uF 100V J
C2523QFN C 2AJ-104ZM CAPACITOR0.1uF 100V J
C2701QETN1HM-475ZE CAPACITOR4.7uF 50V M
C2731NCB31HK-473XC CAPACITOR0.047uF 50V K
C2732NCB 31HK-332XC CA PACITOR3300pF 50V K
C2733NCB31HK-473XC CAPACITOR0.047uF 50V K
C2734NCB 31HK-102XC CA PACITOR1000pF 50V K
C2741NCB31HK-473XC CAPACITOR0.047uF 50V K
C2742NCB 31HK-332XC CA PACITOR3300pF 50V K
C2743NCB31HK-473XC CAPACITOR0.047uF 50V K
C2744NCB 31HK-102XC CA PACITOR1000pF 50V K
Ω
1/16W J950VB,950V
Ω
1/16W J950VB,950V
E,950VEN,9
50VEV,950V
EE
50EN,650EV
E,950VEN,9
50VEV,950V
EE
E,950VEN,9
50VEV,950V
EE
50EN,650EV
E,950VEN,9
50VEV,950V
EE
E,950VEN,9
50VEV,950V
EE
E,950VEN,9
50VEV,950V
EE
C2771QETN1HM-105ZE CAPACITOR1uF 50V M
C2801QEKC1HM-106ZE CA PACITOR10uF 50V M
C2851QETN1CM-107ZE CAPACITOR100uF 16V M
C2853NCB31CK-104XC CA PACITOR0.1uF 16V K
C2901QETN1CM-107ZE CAPACITOR100uF 16V M
C3001NDC31HJ-220XC CAPACITOR22pF 50 V J
C3002NDC31HJ-220XC CAPACITOR22pF 50 V J
C3003NCB31CK-105XC CAPACITOR1uF 16V K
C3004NCB31CK-104XC CA PACITOR0.1uF 16V K
C3005NCB31CK-104XC CA PACITOR0.1uF 16V K
C3006NCB31AK-105XC CAPACITOR1uF 10V K
C3200NCB31HK-104XC CA PACITOR0.1uF 50V K
C3201QETN1EM-477ZE CAPACITOR470uF 25V M
C3202NCB3 1HK-472XC CAPACITOR4700pF 50V K
C3203QETN1EM-477ZE CAPACITOR470uF 25V M
C3205NCB31HK-104XC CA PACITOR0.1uF 50V K
C3301QEKC1HM-475ZE CAPACITOR4.7uF 50V M
C3302QEKC1HM-106ZE CA PACITOR10uF 50V M
C3303NCB31HK-103XC CAPACITOR0.01uF 50V K
C3304QEKC1CM-107ZE CAPACITOR100uF 16V M
C3350NCB31CK-104XC CAPACITOR0.1uF 16V K950VB,950V
C3380QETN1CM-107ZE CAPACITOR100uF 16V M
C3510QETN1HM-226ZE CAPACITOR22uF 50V M950VB,950V
C3521QTE 1J46-106ZE CAPACITOR10u F 63V
C3522NCB31HK-391XC CAPACITOR390pF 50V K
C3531QTE 1J46-106ZE CAPACITOR10u F 63V
C3532NCB31HK-391XC CAPACITOR390pF 50V K
C3550QETN1CM-107ZE CAPACITOR100uF 16V M
C3653QEKC1CM-107ZE CAPACITOR100uF 16V M
C3654QETN1CM-107ZE CAPACITOR100uF 16V M
C3655QETN1CM-107ZE CAPACITOR100uF 16V M
C3712QETN1JM-226ZE CAPACITOR2 2u F 63V M
C3713QETN1HM-226ZE CAPACITOR22u F 50 V M
C3714NCB31HK-103XC CAPACITOR0.01uF 50V K
C3720QETN1HM-106ZE CAPACITOR10u F 50 V M
C3900NCB31HK-103XC CAPACITOR0.01uF 50V K950VB,950V
R2502NRSA63J-362XMG RESISTOR3.6kΩ 1/16W J
R2503NRSA63J-124XMG RESISTOR120k
R2504NRSA63J-513XMG RESISTOR51k
R2511NRSA63J-152XMG RESISTOR1.5k
R2512NRSA63J-122XMG RESISTOR1.2k
R2513NRSA63J-334XMG RESISTOR330k
R2514NRSA63J-183XMG RESISTOR18k
R2515NRSA63J-103XMG RESISTOR10k
R2521NRSA63J-152XMG RESISTOR1.5k
R2522NRSA63J-122XMG RESISTOR1.2k
R2523NRSA63J-334XMG RESISTOR330k
R2524NRSA63J-183XMG RESISTOR18k
R2525NRSA63J-103XMG RESISTOR10k
R2711QRJ 14 3J-681XUNF C RE SI STO R680
R2721QRJ 14 3J-681XUNF C RE SI STO R680
R2731QRJ143J-4R7XUNF C RE SISTOR4.7
R2741QRJ143J-4R7XUNF C RE SISTOR4.7
R2751QRL 01DJ-820XOMF RES ISTOR82
R2752QRL 01DJ-820XOMF RES ISTOR82
R2753QRL 01DJ-820XOMF RES ISTOR82
R3713NRSA63J-753XMG RESISTOR75kΩ 1/16W J
R3714NRSA63J-104XMG RESISTOR100k
R3720QRK126J-4 70XUN F C RES IS TOR47
R3721QRK126J-4 70XUN F C RES IS TOR47
R3730NRSA63J-562XMG RESISTOR5.6k
R4001NRSA63J-750XMG RESISTOR75
C101NCB31CK-104XC CAPACITOR0.1uF 16V K
C102NCB31CK-104XC CAPACITOR0.1uF 16V K
C103NCB31CK-104XC CAPACITOR0.1uF 16V K
C104NCB31CK-104XC CAPACITOR0.1uF 16V K
C105NEAF0JM-476XE C APACITOR47uF 6. 3V M
C106NBE20JM-22 6XTA E CAPACITOR22uF 6.3V M
C107NCB31CK-104XC CAPACITOR0.1uF 16V K
C108NBE20JM-22 6XTA E CAPACITOR22uF 6.3V M
C109NCB20JK-475XC CAPACITOR4. 7uF 6.3V K
C201NDC31HJ-221XC CAPACITOR220pF 50V J
C202NDC31HJ-221XC CAPACITOR220pF 50V J
C203NCB31HK-103XC CAPACITOR0.01uF 50V K
C204NCB31CK-104XC CAPACITOR0.1uF 16V K
C205NCB31HK-271XC CAPACITOR270pF 50V K
C206NDC31HJ-151XC CAPACITOR150pF 50V J
C210NCF31AZ-105XC CAPACITOR1uF 10V Z
C211NCB31HK-223XC CAPACITOR0.022uF 50V K
C217NCB31CK-104XC CAPACITOR0.1uF 16V K
C251NCB31AK-474XC CAPACITOR0. 47 uF 10V K
C256NCB31CK-104XC CAPACITOR0.1uF 16V K
C257NCB31HK-822XC CAPACITOR8200pF 50V K
C258NCB31HK-153XC CAPACITOR0.015uF 50V K
C259NCB31HK-153XC CAPACITOR0.015uF 50V K
C260NCB31HK-223XC CAPACITOR0.022uF 50V K
C261NCB31HK-223XC CAPACITOR0.022uF 50V K
C262NCB31HK-223XC CAPACITOR0.022uF 50V K
C263NEAF1CM-107XE CAPACITOR100uF 16V M
C301NEAF0JM-227XE CAPACITOR220uF 6.3V M
C302NEAF0GM-476XE CAPACITOR47uF 4V M
C303NEAF0GM-476XE CAPACITOR47uF 4V M
C304NCB30JK-105XC CAPACITOR1uF 6.3V K
C305NCB31CK-104XC CAPACITOR0.1uF 16V K
C306NCB31CK-104XC CAPACITOR0.1uF 16V K
C307NCB31CK-104XC CAPACITOR0.1uF 16V K
C309NCB31CK-104XC CAPACITOR0.1uF 16V K
C310NCB31CK-104XC CAPACITOR0.1uF 16V K
C312NCB31CK-104XC CAPACITOR0.1uF 16V K
C313NCB31CK-104XC CAPACITOR0.1uF 16V K
C314NCB31CK-104XC CAPACITOR0.1uF 16V K
C315NCB31CK-104XC CAPACITOR0.1uF 16V K
C316NCB31CK-104XC CAPACITOR0.1uF 16V K
C318NCB31CK-104XC CAPACITOR0.1uF 16V K
C319NCB31CK-104XC CAPACITOR0.1uF 16V K
C320NCB31CK-104XC CAPACITOR0.1uF 16V K
C321NCB31CK-104XC CAPACITOR0.1uF 16V K
C322NCB31CK-104XC CAPACITOR0.1uF 16V K
C323NCB31CK-104XC CAPACITOR0.1uF 16V K
C324NCB30JK-105XC CAPACITOR1uF 6.3V K
C325NDC31HJ-120XC CAPACITOR12pF 50V J
C326NDC31HJ-100XC CAPACITOR10pF 50V J
C328NCB31HK-103XC CAPACITOR0.01uF 50V K
C330NCB31CK-104XC CAPACITOR0.1uF 16V K
C331NCB31CK-333XC CAPACITOR0.033uF 16V K
C332NCB31CK-104XC CAPACITOR0.1uF 16V K
C333NCB31CK-104XC CAPACITOR0.1uF 16V K
C334NCB31CK-104XC CAPACITOR0.1uF 16V K
C335NCB31CK-104XC CAPACITOR0.1uF 16V K
C337NCB31HK-183XC CAPACITOR0.018uF 50V K
C338NCB31HK-562XC CAPACITOR5600pF 50V K
C339NBE20JM-10 6XTA E CAPACITOR10uF 6.3V M
C340NCB30JK-105XC CAPACITOR1uF 6.3V K
C341NCB30JK-105XC CAPACITOR1uF 6.3V K
C345NCB31CK-104XC CAPACITOR0.1uF 16V K
C347NCB31CK-104XC CAPACITOR0.1uF 16V K
C348NCB31CK-104XC CAPACITOR0.1uF 16V K
C349NCB31CK-104XC CAPACITOR0.1uF 16V K
C350NCB31HK-222XC C APACITOR2200pF 50V K
C351NCB31HK-103XC CAPACITOR0.01uF 50V K
C352NCB31HK-153XC CAPACITOR0.015uF 50V K
C353NCB31HK-561XC CAPACITOR560pF 50V K
C354NCB31HK-561XC CAPACITOR560pF 50V K
C356NCB30JK-105XC CAPACITOR1uF 6.3V K
C359NCB30JK-105XC CAPACITOR1uF 6.3V K
C370NCB31CK-104XC CAPACITOR0.1uF 16V K
C371NCF31AZ-105XC CAPACITOR1uF 10V Z
C372NCB31CK-104XC CAPACITOR0.1uF 16V K
C373NCB31CK-104XC CAPACITOR0.1uF 16V K
C374NCB31CK-104XC CAPACITOR0.1uF 16V K
C375NCB31CK-104XC CAPACITOR0.1uF 16V K
C378NCB31CK-104XC CAPACITOR0.1uF 16V K
C379NCB31CK-104XC CAPACITOR0.1uF 16V K
C380NCB21CK-105XC CAPACITOR1uF 16V K
C381NCB21AK-225XC CAPACITOR2.2uF 10V K
C383NCB31CK-104XC CAPACITOR0.1uF 16V K
C391NEAF0JM-227XE CAPACITOR220uF 6.3V M
C392NCB31CK-104XC CAPACITOR0.1uF 16V K
C393NCB31HK-103XC CAPACITOR0.01uF 50V K
C455NCB31HK-103XC CAPACITOR0.01uF 50V K
C551NCB31CK-104XC CAPACITOR0.1uF 16V K
C554NCB31CK-104XC CAPACITOR0.1uF 16V K
C555NCB31CK-104XC CAPACITOR0.1uF 16V K
C557NCB31HK-102XC C APACITOR1000pF 50V K
C558NBE2 0JM-226XTA E CAPACITOR22 uF 6 .3 V M
C559NCB31CK-104XC CAPACITOR0.1uF 16V K
C560NCB31CK-104XC CAPACITOR0.1uF 16V K
C562NCF31AZ-105XC CAPACITOR1uF 10V Z
C563NCB31CK-104XC CAPACITOR0.1uF 16V K
C564NCB31CK-104XC CAPACITOR0.1uF 16V K
C701NCB31CK-104XC CAPACITOR0.1uF 16V K
C704NEAF0JM-476XE CAPACITOR47uF 6.3V M
C706NEAF1CM-106XE CAPACITOR10uF 16V M
C707NCB31CK-104XC CAPACITOR0.1uF 16V K
C711NCB21CK-105XC C APACITOR1uF 16V K
C712NCB31HK-103XC CAPACITOR0.01uF 50V K
C713NCB21CK-105XC CAPACITOR1uF 16V K
C740NCB31CK-104XC CAPACITOR0.1uF 16V K
C801NCB21CK-105XC CAPACITOR1uF 16V K
C802NCB21AK-225XC CAPACITOR2.2uF 10V K
C803NEAF0JM-227XE CAPACITOR220uF 6.3V M
C804NCB31HK-471XC CAPACITOR470pF 50V K
No additional / supplemental order of WARRANTY CARDs are available.
Block No.
MMM3
Only 950VE,EN,EV,EE
A1,A7
A8,A9
P4
Only
950VEE
A11
A12
A11
A15
A12
P5
P5
Only 650E,EVOnly 650EN
A1,A2,A3
A4,A7,A8
A9
A13
Only
950VB,650B
A1,A6
A7,A8
A9
P4
A1,A2,A3
A4,A5,A7
A8,A9
P4P4
A10
P2
P7
P6
P3
A16
3-18
P1
Page 39
Packing and Accessories
Block No. [M][3][M][M]
Symbol No.Part No.Part NameDescriptionLocal
A 1GVT0254-001AIN ST BOOKENG950VB
A 1GVT0254-002AINST BO OKGER FRE ITA DUT950VE
A 1GVT0254-003AINST BO OKSPA DAN FIN SWE POR950VEN
A 1GVT0254-004AINST BO OKHUN CZE POL950VEV
A 1GVT0254-005AIN ST BOOKRUS950VEE
A 1GVT0253-001AIN ST BOOKENG650B
A 1GVT0253-002AIN ST BOOKGER650E
A 1GVT0253-006AIN ST BOOKSPA650EN
A 1GVT0253-011AINST BO OKPOL650EV
A 2GVT0253-003AIN ST BOOKFRE650E
A 2GVT0253-007AIN ST BOOKSWE650EN
A 2GVT0253-012AIN ST BOOKHUN650EV
A 3GVT0253-004AIN ST BOOKDUT650E
A 3GVT0253-008AIN ST BOOKFIN65 0EN
A 3GVT0253-013AIN ST BOOKCZE650EV
A 4GVT0253-005AIN ST BOOKITA650E
A 4GVT0253-009AIN ST BOOKDAN650EN
A 4GVT0253-014BIN ST BOOKRUS650EV
A 5GVT0253-010AIN ST BOOKPOR650EN
A 6VNA3000-204REGIST CARD950VB,650B
A 7- --- --- -----WARR AN TY CARDBT-54036-1950VB,950VE, 950VEN,950VEV,950VEE,650B
A 7------------WARRANTY CARDBT-54035-1650E,650EN,650EV
A 8GVT0252-001ACAUTION SHEET950VB,650B
A 8GVT0252-002ACAUTION SHEET950VE,950VEN, 650E,650EN
A 8GVT0252-003ACAUTION SHEET950VEV,950VEE,650EV
A 9LVT1923-001ACAUTION SHEET
A 10QA L1123-001AM LOOP ANT
A 11QA L04 57-001ANT.WIRE
A 12------------BATTERY(x2)
A 13RM-S UXG500VRREMOTE CO NTROL UNIT950VB,950VE, 950VEN,950VEV,950VEE
A 13RM-S UXG650RREMOTE CONTRO L UNIT650B,650E,650EN,650EV
A 15QQR1607-001FER R I TE CORE950VB,950VE, 950 VEN,950VEV,650B,650E,650 EN, 650EV
A 16SPUXG950V-SPBOXSPK WITH BOX(x2)950VB,95 0VE,950VEN,950V EV,950VEE
A 16SPUXG650-SPBOXSPK WITH BOX(x2)650B,650E,650EN, 65 0EV
P 1GV31189-008ACARTON BOX950VB,950VE,950VEN,950VEV
P 1GV31189-009ACARTON BOX950VEE
P 1GV31189-010ACARTON BOX650B,650E,650EN,650EV
P 2GV10425-001ACUSHION(TOP)
P 3GV10426-001ACUSHION(BOTTOM)
P 4QPC02503515 PBPOLY BAG25cm x 35cm
P 5QPA012025 05POLY BAG12cm x 25cm
P 6QPC05006515 PBPOLY BAG50cm x 65cm
P 7GV40437-007ACLOTH
3-19
Page 40
SCHEMATIC DIAGRAMS
MICRO COMPONENT SYSTEM
UX-G950VB, UX-G950VE, UX-G950VEN,
UX-G950VEV, UX-G950VEE, UX-G650B,
UX-G650E, UX-G650EN, UX-G650EV
DVD-ROM No.SML2008Q2
UX-G950V
SUPER VIDEO
SP-UXG950VSP-UXG950VCA-UXG950V
UX-G650
Lead free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade)
Lead free solder used in the board (material : Sn-Cu, melting point : 230 Centigrade)
Contents
Block diagrams
Standard schematic diagrams
Printed circuit boards
UX-G950VB / UX-G950VE
UX-G950VEE / UX-G950VEV
UX-G950VEE
SUPER VIDEO
SP-UXG650
CA-UXG650
SP-UXG650
2-1
2-2
2-11 to 13
COPYRIGHT 2008 Victor Company of Japan, Limited.
No.MB682SCH<Rev.001>
2008/8
Page 41
In regard with component parts appearing on the silk-screen printed side (parts side) of the PWB diagrams, the
parts that are printed over with black such as the resistor ( ), diode ( ) and ICP ( ) or identified by the " "
mark nearby are critical for safety.