Lead free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade)
Lead free solder used in the board (material : Sn-Cu, melting point : 230 Centigrade)
Design and specifications are subject to change without notice.
(No.MB674<Rev.003>)1-3
SECTION 1
PRECAUTION
1.1Safety Precautions
(1) This design of this product contains special hardware and
many circuits and components specially for safety purposes. For continued protection, no changes should be made
to the original design unless authorized in writing by the
manufacturer. Replacement parts must be identical to
those used in the original circuits. Services should be performed by qualified personnel only.
(2) Alterations of the design or circuitry of the product should
not be made. Any design alterations of the product should
not be made. Any design alterations or additions will void
the manufacturers warranty and will further relieve the
manufacture of responsibility for personal injury or property
damage resulting therefrom.
(3) Many electrical and mechanical parts in the products have
special safety-related characteristics. These characteristics are often not evident from visual inspection nor can the
protection afforded by them necessarily be obtained by using replacement components rated for higher voltage, wattage, etc. Replacement parts which have these special
safety characteristics are identified in the Parts List of Service Manual. Electrical components having such features
are identified by shading on the schematics and by ( ) on
the Parts List in the Service Manual. The use of a substitute
replacement which does not have the same safety characteristics as the recommended replacement parts shown in
the Parts List of Service Manual may create shock, fire, or
other hazards.
(4) The leads in the products are routed and dressed with ties,
clamps, tubings, barriers and the like to be separated from
live parts, high temperature parts, moving parts and/or
sharp edges for the prevention of electric shock and fire
hazard. When service is required, the original lead routing
and dress should be observed, and it should be confirmed
that they have been returned to normal, after reassembling.
(5) Leakage shock hazard testing
After reassembling the product, always perform an isolation check on the exposed metal parts of the product (antenna terminals, knobs, metal cabinet, screw heads,
headphone jack, control shafts, etc.) to be sure the product
is safe to operate without danger of electrical shock.Do not
use a line isolation transformer during this check.
• Plug the AC line cord directly into the AC outlet. Using a
"Leakage Current Tester", measure the leakage current
from each exposed metal parts of the cabinet, particularly any exposed metal part having a return path to the
chassis, to a known good earth ground. Any leakage current must not exceed 0.5mA AC (r.m.s.).
• Alternate check method
Plug the AC line cord directly into the AC outlet. Use an
AC voltmeter having, 1,000Ω per volt or more sensitivity
in the following manner. Connect a 1,500Ω 10W resistor
paralleled by a 0.15µF AC-type capacitor between an ex-
posed metal part and a known good earth ground.
Measure the AC voltage across the resistor with the AC
voltmeter.
Move the resistor connection to each exposed metal
part, particularly any exposed metal part having a return
path to the chassis, and measure the AC voltage across
the resistor. Now, reverse the plug in the AC outlet and
repeat each measurement. Voltage measured any must
not exceed 0.75 V AC (r.m.s.). This corresponds to 0.5
mA AC (r.m.s.).
AC VOLTMETER
(Having 1000
ohms/volts,
or more sensitivity)
0.15 F AC TYPE
Place this
probe on
1500 10W
Good earth ground
1.2Warning
(1) This equipment has been designed and manufactured to
meet international safety standards.
(2) It is the legal responsibility of the repairer to ensure that
these safety standards are maintained.
(3) Repairs must be made in accordance with the relevant
safety standards.
(4) It is essential that safety critical components are replaced
by approved parts.
(5) If mains voltage selector is provided, check setting for local
voltage.
1.3Caution
Burrs formed during molding may be left over on some parts
of the chassis.
Therefore, pay attention to such burrs in the case of preforming repair of this system.
1.4Critical parts for safety
In regard with component parts appearing on the silk-screen
printed side (parts side) of the PWB diagrams, the parts that are
printed over with black such as the resistor ( ), diode ( )
and ICP ( ) or identified by the " " mark nearby are critical
for safety. When replacing them, be sure to use the parts of the
same type and rating as specified by the manufacturer.
(This regulation dose not Except the J and C version)
each exposed
metal part.
1-4 (No.MB674<Rev.003>)
1.5Preventing static electricity
Electrostatic discharge (ESD), which occurs when static electricity stored in the body, fabric, etc. is discharged, can destroy the laser
diode in the traverse unit (optical pickup). Take care to prevent this when performing repairs.
1.5.1 Grounding to prevent damage by static electricity
Static electricity in the work area can destroy the optical pickup (laser diode) in devices such as laser products.
Be careful to use proper grounding in the area where repairs are being performed.
(1) Ground the workbench
Ground the workbench by laying conductive material (such as a conductive sheet) or an iron plate over it before placing the
traverse unit (optical pickup) on it.
(2) Ground yourself
Use an anti-static wrist strap to release any static electricity built up in your body.
(caption)
Anti-static wrist strap
1M
Conductive material
(conductive sheet) or iron palate
(3) Handling the optical pickup
• In order to maintain quality during transport and before installation, both sides of the laser diode on the replacement optical
pickup are shorted. After replacement, return the shorted parts to their original condition.
(Refer to the text.)
• Do not use a tester to check the condition of the laser diode in the optical pickup. The tester's internal power source can easily
destroy the laser diode.
1.6Handling the traverse unit (optical pickup)
(1) Do not subject the traverse unit (optical pickup) to strong shocks, as it is a sensitive, complex unit.
(2) Cut off the shorted part of the flexible cable using nippers, etc. after replacing the optical pickup. For specific details, refer to the
replacement procedure in the text. Remove the anti-static pin when replacing the traverse unit. Be careful not to take too long a
time when attaching it to the connector.
(3) Handle the flexible cable carefully as it may break when subjected to strong force.
(4) I t is not possible to adjust the semi-fixed resistor that adjusts the laser power. Do not turn it.
1.7Attention when traverse unit is decomposed
*Please refer to "Disassembly method" in the text for the pickup unit.
• Apply solder to the short land sections before the card wire is disconnected from the connecto on the servo board. (If the card wire
is disconnected without applying solder, the pickup may be destroyed by static electricity.)
• In the assembly, be sure to remove solder from the short land sections after connecting the card wire.
Solder short land section
(No.MB674<Rev.003>)1-5
1.8Important for laser products
1.CLASS 1 LASER PRODUCT
2.CAUTION :
(For U.S.A.) Visible and/or invisible class II laser radiation
when open. Do not stare into beam.
(Others) Visible and/or invisible class 1M laser radiation
when open. Do not view directly with optical instruments.
3.CAUTION : Visible and/or invisible laser radiation when
open and inter lock failed or defeated. Avoid direct
exposure to beam.
4.CAUTION : This laser product uses visible and/or invisible
laser radiation and is equipped with safety switches which
prevent emission of radiation when the drawer is open and
the safety interlocks have failed or are defeated. It is
dangerous to defeat the safety switches.
5.CAUTION : If safety switches malfunction, the laser is able
to function.
6.CAUTION : Use of controls, adjustments or performance of
procedures other than those specified here in may result in
hazardous radiation exposure.
!
Please use enough caution not to
see the beam directly or touch it
in case of an adjustment or operation
check.
REPRODUCTION AND POSITION OF LABELS and PRINT
WARNING LABEL and PRINT
1-6 (No.MB674<Rev.003>)
SECTION 2
SPECIFIC SERVICE INSTRUCTIONS
This service manual does not describe SPECIFIC SERVICE INSTRUCTIONS.
SECTION 3
DISASSEMBLY
3.1Main body (Used figure are UX-G500V)
3.1.1 Removing the Metal Cover (See Fig.1,2)
(1) Remove the seven screws A attaching the Metal cover.
(See Fig.1)
(2) Remove the two screws B attaching the both side of the
Metal cover. (See Fig.2)
AA
Fig.1
B
Fig.2
(No.MB674<Rev.003>)1-7
3.1.2 Removing the Tuner pack (See Fig.3, 4)
(1) Disconnect the card wire from Tuner pack connected to
connector CN306
(2) Remove the two screws C attaching the Tuner pack. (See
Fig.4)
of the Micom board. (See Fig.3)
CN306
Fig.3
C
3.1.3 Removing the Rear panel (See Fig.5)
(1) Remove the five screws D attaching the Rear panel.
Fig.4
D
Fig.5
1-8 (No.MB674<Rev.003>)
3.1.4 Removing the Amp board (See Fig.6)
(1) Disconnect the connector wire from Power board connect-
ed to connector CN640
(2) Disconnect the card wire from Amp board connected to
connector CN520
(3) Remove the one screw E attaching the Amp board.
3.1.5 Removing the DVD mechanism (See Fig.7 to 8)
(1) Disconnect the card wire from DVD mechanism connected
to connector CN360
(See Fig.7)
(2) Disconnect the connector wire from DVD mechanism con-
nected to connector CN811
Fig.7)
(3) Disconnect the card wire from DVD mechanism connected
to connector CN205
(4) Disconnect the card wire from DVD mechanism connected
to connector CN510 of the Micom board. (See Fig.7)
(5) Remove the two screws F attaching the DVD mechanism.
(See Fig.8)
of the Amp board.
of the Micom board.
and CN361 of the Connection board.
of the Connection board. (See
of the Power board. (See Fig.7)
CN520
E
CN640
Fig.6
CN205 CN361CN360CN811CN510
Fig.7
Fig.8
F
(No.MB674<Rev.003>)1-9
3.1.6 Removing the Mecha chassis (See Fig.9, 10)
(1) Remove the two screws G attaching the both side of the
Front panel. (See Fig.9)
(2) Disconnect the card wire from Connection board connect-
ed to connector CN310
of the Micom board. (See Fig.10)
G
Fig.9
CN310
Fig.10
1-10 (No.MB674<Rev.003>)
3.1.7 Removing the Front panel (See Fig.11 to 13)
(1) Disconnect the card wire from FL board connected to con-
nector CN304
(2) Disconnect the card wire from Volume board connected to
connector CN303
(3) Remove the one screw J attaching the Volume board. (See
Fig.11)
(4) Remove the two screws H attaching the Front panel. (See
Fig.12)
(5) Disengage two hooks a engaged both side of the Front
panel. (See Fig.12)
(6) Disengage one hook b engaged bottom side of the Front
panel. (See Fig.13)
of the Micom board. (See Fig.11)
of the Micom board. (See Fig.11)
CN303
CN304
J
H
Fig.11
hook b
Fig.12
hook
a
Fig.13
(No.MB674<Rev.003>)1-11
3.1.8 Removing the Micom board (See Fig.14, 15)
(1) Remove the two screws K attaching the Micom board.
(See Fig.14)
(2) Disconnect the flat cable wire from Micom board connected
to connector CN201
Fig.15)
(3) Disconnect the board to board connector connected to
connector CN204
(4) Disconnect the board to board connector connected to
connector CN803 of the USB jack board. (See Fig.15)
and CN203 of the Power board. (See
of the Power board. (See Fig.15)
K
Fig.14
CN201
CN803CN203CN204
Fig.15
1-12 (No.MB674<Rev.003>)
3.1.9 Removing the USB jack board (See Fig.16)
(1) Remove the three screws L attaching the USB jack board.
3.1.10 Removing the Power board (See Fig.16)
(1) Disconnect the power cord connected to connector CN200
of the Power board.
(2) Remove the four screws M attaching the Power board.
L
3.1.11 Removing the FL board (See Fig.17)
(1) Remove the six screws N attaching the FL board.
3.1.12 Removing the Volume board (See Fig.17)
(1) Remove the volume knob.
(2) Remove the eight screws P attaching the Volume board.
N
P
CN200
Fig.16
MM
N
P
Fig.17
(No.MB674<Rev.003>)1-13
3.2DVD mechanism
3.2.1 Removing the traverse mechanism
(See Fig.1 to 6)
(1) Remove the two screws A attaching the tramecha holder
from top side of DVD mechanism assembly. (See Fig.1)
(2) Remove the two screws B attaching the DVD module
board. (See Fig.2)
(3) Remove the four screws C attaching the CB holder and
take out it. (See Fig.3)
(4) Remove the four screws D attaching the traverse mecha-
nism. (See Fig.4)
(5) Solder the solder part of DVD pick up. (See Fig.5)
(6) Disconnect the card wire from CN101
DVD module board. (See Fig. 6)
Caution:
• Solder the short land section on the DVD pickup before dis-
connecting the card wire from the connector on the DVD
pickup. If the card wire is disconnected without attaching solders, the pickup may be destroyed by static electricity.
• When attaching the DVD pickup, be sure to remove solders
from the short land section after connecting the card wire to
the connector on the DVD pickup.
and CN201 on the
A
Clamper base
B
A
DVD mechanism assembly
Fig.1
DVD mechanism assembly
B
1-14 (No.MB674<Rev.003>)
DVD module board
Fig.2
DVD module board
Solder short land section
Fig.5
C
C
CC
Fig.3
DVD mechanism assembly
Traverse mechanism assembly
DVD module board
CN101
CN201
Fig.6
DD
Fig.4
(No.MB674<Rev.003>)1-15
3.2.2 Removing the pickup assembly
(See Fig.7 to 11)
(1) Remove the two rod springs pressing the guide shaft. (See
Fig.7)
(2) Remove the screw E and F attaching the spring holder.
(See Fig.8)
(3) Remove the read screw from traverse mechanism assem-
bly. (See Fig.9)
Caution:
When remove the lead screw, do not loss the middle
gear. (See Fig.10 and 11)
(4) Remove the bar spring pressing the shaft. (See Fig.10)
(5) Take out the pickup assembly from traverse mechanism
chassis by order. (See Fig.11)
(SHAFT)
(T.TABLE)
HOOK
(BAR SPRING)
Fig.10
ROD SPRINGROD SPRING
Fig.7
Spring holder
Fig.8
order 2
order 3
order 1
Fig.11
EF
Middle gear
Lead screw
Fig.9
1-16 (No.MB674<Rev.003>)
3.2.3 Removing the feed motor assembly
(See Fig.12)
(1) Remove the one screw G attaching the feed motor assem-
bly.
(2) Remove the feed motor wires from solder part of spindle
motor board.
Solder part
3.2.4 Removing the spindle motor assembly
(See Fig.13)
(1) Remove the three screws H attaching the spindle motor
from spindle motor board.
Middle gear
Lead screw
Fig.12
H
Spindle motor
Fig.13
G
(No.MB674<Rev.003>)1-17
3.2.5 Removing the tray assembly
(See Fig.14 & 15)
(1) Remove the two screws J attaching the clamper base.
(See Fig.14)
(2) Remove the one screw K attaching the shaft guide from
bottom side. (See Fig.14)
(3) Remove the two screws L attaching the shaft guide from
top side. (See Fig.15)
Caution:
When attach the tray assembly, boss of loading sub assembly
should attach to guide of bottom side at tray assembly. (See
Fig.15)
J
order 1
order 2
clamper base
L
K
Fig.15
[bottom side]
Fig.14
1-18 (No.MB674<Rev.003>)
SECTION 4
ADJUSTMENT
4.1DVD test mode
(1) Press "DVD/CD" key + "STOP" key on panel, then AC in.
(2) FL display "T xxx xx"
(3) Press "MENU/PL" key repeatedly, until FL display
"CHECK"
(4) Press number key on Remote control "1-10,0 and >=10"
Key 1 : "PLAYBACK"
Key 2 : "WOBBLE"
Key 3 : "TNO-1 SR"
Key 4 : "CDLD LSR"
Key 5 : "DVDLD LSR"
Key 6 : "JITX1"
Key 7 : "EEP BWD"
Key 8 : "EEPFWD"
Key 9 : "TEMP"
4.2SYSTEM micom test mode
(1) In DVD/CD mode, press
"SET" key + "9" key + "POWER" key repeatedly
System micom version
G500V : "
32846 00" (1st issued)
DVD/CD micom version
"DVD 0258"
(FL ALL DISPLAY)
Set destiunation
eg: "V_U1_9K"
Model name
eg: "G500V"
Key 10 : "DVD-LD"
Key 0 : "MONITOR"
Key >10 : "INIT"
4.3GENERAL
KEYINDICATIONFUNCTION
SET + "10" + POWERCOLDCOLD START
(Initialization of set)
SET + "1" + POWER00000:00 -> TMP 0000 ->
L.DET 00 -> V.DROP 0
SET + "4" + POWERVOLUME20 -> VOL MAXVolume level to max by compulsion
SET + "9" + POWERRefer SYSCON TESTRefer SYSCON TEST
(FL ALL DISPLAY)FL all displaySET + ">10" + POWER
Total DVD/CD mode play time by Hour:Minutes ->
Mecha temperature data ->
Speaker level detect over trigger level by percentage, % ->
Volume level drop, 1, 2 then 3, each -2db
SECTION 5
TROUBLESHOOTING
This service manual does not describe TROUBLESHOOTING.
(No.MB674<Rev.003>)1-19
Victor Company of Japan, Limited
Audio/Video Systems Division 10-1,1chome,Ohwatari-machi,Maebashi-city,371-8543,Japan
* All printed circuit boards and its assemblies are not available as service parts.
- Contents -
Exploded view of general assembly and parts list (Block No.M1)
DVD mechanism assembly and parts list (Block No.MJ)
DVD loading base assembly and parts list (Block No.MN) [FMU-MB6-71M]
DVD mechanism assembly and parts list (Block No.MU) [FMU-MH2-71M]
Electrical parts list (Block No.01~07)
Packing materials and accessories parts list (Block No.M3)
MB674PAR<Rev.003>
[FXL-D10-1M]
3- 2
3- 6
3- 8
3-10
3-12
3-22
3-1
Exploded view of general assembly and parts list
P
2
2
23
Front View
Block No.
MMM1
14
53
18
3
4
O
1
7
12
23
Q
12
FL board
S
J
58
63
51
62
50
9
9
9
9
R
56
S
22
P
10
K
D
10
13
P
6
8
45
C
45
6
10
28
K
61
11
28
L
60
28
M
59
B
17
H
28
B
21
3
10
Switch board
10
10
28
Power board
2
27
A
10
47
C
5
49
55
R
H
F
57
J
K
19
3-2
D
29
Main board
30
26
B
G
21
48
A
30
67
9
10
28
Power board
A
48
28
K
MM1
61
11
Only
14
53
UX-G500UF
18
O
20
14
44
46
S
43
44
J
58
R
56
S
22
P
13
28
L
60
M
54
Q
N
K
46
E
24
15
L
O
N
G
AMP board
37
44
44
44
33
52
F
34
28
M
59
B
17
28
16
H
16
Connection
board
64
Only
UX-G500A,US,UB,UW,UX,
B
65
25
38
39
UG,UN,UF,UP,UT,UH
21
32
26
31
B
72
32
Only UX-G500UT
31
E
Only
UX-G500UT
70
36
41
42
35
40
71
Only
UX-G500UH
68
Only
UX-G500UF
69
Only
UX-G500UP
66
30
Only
UX-G500UF
30
The parts without symbol number are not service.
3-3
General Assembly
Block No. [M][1][M][M]
Symbol No.Part No.Part NameDescriptionLocal
1GV10404-009AFRONT PANELB,E,EN,EV,EE
1GV10404-010AFRONT PANELA,US,UB,UW,UX,UG,UN,UF,UP,UT,UH
2GV20500-004AFRONT LENSB,E,EN,EV,EE
2GV20500-005AFRONT LENSA,US,UB,UW,UX,UG,UN,UF,UP,UT,UH
3GV31132-001ALIGHTING LENS
4GV31133-001ALENS COVER
5GV31136-007AUSB LENS
6GV40764-001AFOOT SPACER(x2)
7GV31130-002AF.BUTTON ASSY
8GV20502-001ABUTTON
9QYSDSF2608ZATAP SCREWM2.6 x 8mm(x6)
10QYSDSF2608ZATAP SCREWM2.6 x 8mm(x9)
11QYSDSG3008ZATAP SCREWM3 x 8mm
12GV30349-091ASPACER(x2)
13GV10405-001AMECHA HOLDER
14QYSBSF3010ZATAP SCREWM3 x 10mm(x2)
15QYSDSG3008ZATAP SCREWM3 x 8mm
16LV44209-001AWASHER SCREW(x3)
17LV44209-001AWASHER SCREW
18GV30349-048ASPACER
19GV30349-014ASPACER
20GV30349-092ASPACER
21GV30349-076ASPACER(x2)
22GV30349-026ASPACER
23QYSSSF3010ZATAP SCREWM3 x 10mm(x2)
24GV31137-001AHEAT SINK
25QYSDSG3008ZATAP SCREWM3 x 8mm(x2)
26GV10406-001ABOTTOM CHASSIS
27QYSDSG3006ZATAP SCREWM3 x 6mm(x3)
28QYSDSG3006ZATAP SCREWM3 x 6mm(x5)
29QYSDSG3006ZATAP SCREWM3 x 6mm(x2)
30GV40764-001AFOOT SPACER(x2)
1LV22234-003AT.M.CHASSIS
2LV22235-002ASPINDLE BASE
3QYSDST2005ZATAP SCREWM2 x 5mm(x2)
4LV36555-001AG.S.HOLDER
5QYSDST2005ZATAP SCREWM2 x 5mm
6LV44041-002AGUIDE SHAFT
7LV44479-001ABAR SPRING
8LV22236-001AFEED HOLDER
9QAR0165-001FEED MOTOR5.0V DC
10LV30225-0X5ASPACER(x2)
11LV36557-001AF.M.GEAR
12QYSPSPT2030MASCREWM2 x 3mm
13QYSDST2005ZATAP SCREWM2 x 5mm
14QAL0786-006PICK UP
14orQAL0786-004PICK UP
15LV22237-001ARACK ARM
16LV36560-001ARACK ARM SPRING
17QYSPSFU1740ZATAP SCREWM1.7 x 4mm(x2)
18QUQK05-2415AC-EFFC WIRE24pin 15cm
20LV44041-002AGUIDE SHAFT
21LV36559-001AL.S.GEAR
22LV41517-003ALEAD SCREW
23LV36558-001AMIDDLE GEAR
24LV36556-001ASPRING HOLDER
25LV44623-001ACOMP.SPRING
26QYSDST2005ZATAP SCREWM2 x 5mm
27QYSDST2616MATAP SCREWM2.6 x 16mm
28QAR0386-001S.MOTOR
29QYSPSPU1775ZASCREWM1.7 x 7.5mm(x3)
30LV44042-001AROD SPRING(x2)
31LV44046-001AADJUST SCREW(x4)
Block No. [M][J][M][M]
3-7
DVD loading base assembly and parts list
FMU-MB6-71M
Grease
JVS-1003
CFD-4007ZY2
15
h
18
19
17
26
2
14
Block No.
3
11
13
11
MMMN
1
h
< Back side >
25
A
B
24
24
DVD module board
15
j
16
10
9
7.75mm
0.10mm
4
7
8
6
k
e
Back side
5
f
25
c
j
d
12
22
24
24
23
22
21
c
3-8
22
21
B
A
21
22
DVD loading
switch board
21
f
20
e
d
The parts without symbol number are not service.
DVD loading base (FMU-MB6-71M)
Symbol No.Part No.Part NameDescriptionLocal
1LV11065-014ALOADER SUB ASSY
2E407140-001SSC.D ROLLER
3E407149-001SSRUBBER TUBE
4LV10979-003ATRAY
5LV35499-003ASHAFT GUIDE
6LV44022-001ASHAFT
7QYSSSF2008ZATAP SCREWM2 x 8mm
8QYSDSF2008ZATAP SCREWM2 x 8mm(x2)
9QAR0197-001MOTOR2.0V DC
9orQAR0450-001MOTOR
10LV43844-002AMOTOR PULLEY
11QYSPSPU1730ZASCREWM1.7 x 3mm(x2)
12QYSDSF2008ZATAP SCREWM2 x 8mm
13LV43974-001ABELT
14LV21852-003ACLAMPER BASE
15QYSDSF2008ZATAP SCREWM2 x 8mm(x2)
16LV35056-002ADVD CLAMPER
17LV42930-003AMAGNET
17orLV41118-003AMAGNET
18LV43848-001AYOKE
19LE40906-002A-MSPECIAL SCREW
20------------SINGLE DVD TRAM
21LV44043-001AINSULATOR(x4)
22LV44044-001ASPECIAL SCREW(x4)
23LV11212-003ACB HOLDER
24QYSBSF2608ZATAP SCREWM2.6 x 8mm(x4)
25LV44209-001AWASHER SCREW(x2)
26LV44603-003ALASER CAUTION
Block No. [M][N][M][M]
3-9
DVD mechanism assembly and parts list
Grease
JVS-1003
CFD-4007ZY2
JVG-31N
1401C
< Back side >
19
18
17
15
h
FMU-MH2-71M
20
14
Block No.
MMMU
4
7
8
6
2
12
3
11
h
d
10
9
DVD loading
switch board
23
11
13
15
5
42
16
j
41
40
d
55
21
44
22
5454
1
f
j
e
21
22
g
50
g
7.75mm
0.10mm
49
48
55
51
e
55
47
55
43
C
39
< Back side >
53
A
f
21
22
52
46
45
21
22
35
32
30
24
7.0mm
0.2mm
28
28
34
36
31
38
29
33
24
DVD module board
25
B
A
25
3-10
24
27
37
C
26
B
The parts without symbol number are not service.
DVD mechanism (FMU-MH2-71M)
Symbol No.Part No.Part NameDescriptionLocal
1LV11065-014ALOADER SUB ASSY
2E407140-001SSC.D ROLLER
3E407149-001SSRUBBER TUBE
4LV10979-003ATRAY
5LV35499-003ASHAFT GUIDE
6LV44022-001ASHAFT
7QYSSSF2008ZATAP SCREWM2 x 8mm
8QYSDSF2008ZATAP SCREWM2 x 8mm(x2)
9QAR0197-001MOTOR2.0V DC
9orQAR0450-001MOTOR
10LV43844-002AMOTOR PULLEY
11QYSPSPU1730ZASCREWM1.7 x 3mm(x2)
12QYSDSF2008ZATAP SCREWM2 x 8mm
13LV43974-001ABELT
14LV21852-003ACLAMPER BASE
15QYSDSF2008ZATAP SCREWM2 x 8mm(x2)
16LV35056-002ADVD CLAMPER
17LV42930-003AMAGNET
17orLV41118-003AMAGNET
18LV43848-001AYOKE
19LE40906-002A-MSPECIAL SCREW
20LV44603-003ALASER CAUTION
21LV44043-001AINSULATOR(x4)
22LV44044-001ASPECIAL SCREW(x4)
23LV11212-003ACB HOLDER
24QYSBSF2608ZATAP SCREWM2.6 x 8mm(x4)
25LV44209-001AWASHER SCREW(x2)
26LV22234-004AT.M.CHASSIS
27LV22235-002ASPINDLE BASE
28QYSDST2005ZATAP SCREWM2 x 5mm(x2)
29LV36555-001AG.S.HOLDER
30QYSDST2005ZATAP SCREWM2 x 5mm
31LV44041-002AGUIDE SHAFT
32LV44479-001ABAR SPRING
33LV22236-001AFEED HOLDER
34QAR0165-001FEED MOTOR5.0V DC
35LV30225-0X5ASPACER(x2)
36LV36557-001AF.M.GEAR
37QYSPSPT2030MASCREWM2 x 3mm
38QYSDST2005ZATAP SCREWM2 x 5mm
39QAL1118-001PICK UP
40LV22656-001ARACK ARM
41LV38074-001ARACK ARM SPRING
42VKZ4777-006MINI SCREW(x2)
43QUQU05-2413AC-EFFC WIRE24pin 13cm
44LV44041-002AGUIDE SHAFT
45LV36559-001AL.S.GEAR
46LV41517-003ALEAD SCREW
47LV36558-001AMIDDLE GEAR
48LV36556-001ASPRING HOLDER
49LV44623-001ACOMP.SPRING
50QYSDST2005ZATAP SCREWM2 x 5mm
51QYSDST2616MATAP SCREWM2.6 x 16mm
52QAR0386-001S.MOTOR
53QYSPSPU1775ZASCREWM1.7 x 7.5mm(x3)
54LV44042-001AROD SPRING(x2)
55LV44046-001AADJUST SCREW(x4)
C4101NDC31HJ-331XC CAPACITOR330pF 50V JB,E,EN,EV,EE
C4107QETN1AM-477ZE CAPACITOR470uF 10V MB,E,EN,EV,EE
C4201NDC31HJ-331XC CAPACITOR330pF 50V JB,E,EN,EV,EE
C4302NCB31CK-104XC CAPACITOR0.1uF 16V K
C4400QETN1AM-477ZE CAPACITOR470uF 10V M
C4402NCB31CK-104XC CAPACITOR0.1uF 16V K
C4403NCB31CK-105XC CAPACITOR1uF 16V K
C4404QETN1HM-106ZE CAPACITOR10uF 50V M
C4405QETN1HM-226ZE CAPACITOR22uF 50V M
C4406NCB31CK-105XC CAPACITOR1uF 16V K
C4407NCB31CK-105XC CAPACITOR1uF 16V K
C4408NCB31CK-105XC CAPACITOR1uF 16V K
C4409QETN1AM-477ZE CAPACITOR470uF 10V M
C4410QETN1AM-477ZE CAPACITOR470uF 10V M
C4411QETN1AM-477ZE CAPACITOR470uF 10V M
Part No.Part NameDescriptionLocal
TRANSMITTER
UX,UG,UN,UF,
UP,UT,UH
UX,UG,UN,UF,
UP,UT,UH
UX,UG,UN,UF,
UP,UT,UH
Symbol No.
C5001QETN1CM-107ZE CAPACITOR100uF 16V M
C5003QETN1HM-475ZE CAPACITOR4.7uF 50V M
C5101QETN1HM-106ZE CAPACITOR10uF 50V M
C5102QTE1J46-106ZE CAPACITOR10uF 63V
C5103QETN1HM-106ZE CAPACITOR10uF 50V M
C5104QETN1HM-106ZE CAPACITOR10uF 50V MB,E,EN,EV,EE,
C6001QETN1EM-477ZE CAPACITOR470uF 25V M
C6002QETN1EM-476ZE CAPACITOR47uF 25V M
C6003QETN1EM-476ZE CAPACITOR47uF 25V M
C6004NCB31CK-104XC CAPACITOR0.1uF 16V K
Part No.Part NameDescriptionLocal
C6005NCB31CK-334XC CAPACITOR0.33uF 16V K
C6006QETN1EM-476ZE CAPACITOR47uF 25V M
C6007NCB31HK-104XC CAPACITOR0.1uF 50V K
C6008NCB31CK-104XC CAPACITOR0.1uF 16V KUT
C6052QTE1J46-106ZE CAPACITOR10uF 63V
C6101NCB21EK-474XC CAPACITOR0.47uF 25V K
C6102NCB31CK-474XC CAPACITOR0.47uF 16V K
C6103NCB31CK-105XC CAPACITOR1uF 16V K
C6104NCB31CK-474XC CAPACITOR0.47uF 16V K
C6107NCB31HK-472XC CAPACITOR4700pF 50V KUT
C6110QENC1EM-106ZBP E CAPACITOR10uF 25V M
C6111NCB21EK-474XC CAPACITOR0.47uF 25V K
C6112NCB31CK-474XC CAPACITOR0.47uF 16V K
C6113NCB31CK-105XC CAPACITOR1uF 16V K
C6114NCB31CK-474XC CAPACITOR0.47uF 16V K
C6117NCB31HK-472XC CAPACITOR4700pF 50V KUT
C6152QTE1J46-106ZE CAPACITOR10uF 63V
C6201NCB21EK-474XC CAPACITOR0.47uF 25V K
C6202NCB31CK-474XC CAPACITOR0.47uF 16V K
C6203NCB31CK-105XC CAPACITOR1uF 16V K
C6204NCB31CK-474XC CAPACITOR0.47uF 16V K
C6207NCB31HK-472XC CAPACITOR4700pF 50V KUT
C6210QENC1EM-106ZBP E CAPACITOR10uF 25V M
C6211NCB21EK-474XC CAPACITOR0.47uF 25V K
C6212NCB31CK-474XC CAPACITOR0.47uF 16V K
C6213NCB31CK-105XC CAPACITOR1uF 16V K
C6214NCB31CK-474XC CAPACITOR0.47uF 16V K
C6217NCB31HK-472XC CAPACITOR4700pF 50V KUT
C6401QEZ0863-106ZM CAPACITOR10uF
C6511QEZ0863-106ZM CAPACITOR10uF
C6601QETN1HM-105ZE CAPACITOR1uF 50V M
C6602QETN1HM-226ZE CAPACITOR22uF 50V M
C6611QETN1HM-105ZE CAPACITOR1uF 50V M
C6613NCB31HK-104XC CAPACITOR0.1uF 50V K
C2010QCZ0134-472C CAPACITOR4700pF
C2012QETN1HM-106Z E CAPACITOR10uF 50V M
C2013NDC31HJ-221XC CAPACITOR220pF 50V J
C2014QCZ0136-221ZC CAPACITOR220pF 1kV K
C2015QETN1HM-105Z E CAPACITOR1uF 50V M
C2016NCB31HK-103X C CAPACITOR0.01uF 50V K
C2017NCB31HK-102X C CAPACITOR1000pF 50V K
C2018NDC31HJ-471XC CAPACITOR470pF 50V J
C2020QCZ9134-222C CAPACITOR2200pFB,E,EN,EV,E
C2020QCZ9134-221M CAPACITOR220pFUH
C2100NCB31HK-104X C CAPACITOR0.1uF 50V K
C2101QETN1EM-476Z E CAPACITOR47uF 25V M
C2102NCB31HK-103X C CAPACITOR0.01uF 50V K
C2103NDC31HJ-201XC CAPACITOR200pF 50V J
C2104NCB31HK-104X C CAPACITOR0.1uF 50V KUT
C2105QETN1CM-107Z E CAPACITOR100uF 16V M
C2106NCB31HK-471X C CAPACITOR470pF 50V K
C2107NCB31HK-104X C CAPACITOR0.1uF 50V KB,E,EN,EV,E
C2110NCB31HK-104X C CAPACITOR0.1uF 50V K
C2111QETN1EM-476Z E CAPACITOR47uF 25V M
C2112NCB31HK-103X C CAPACITOR0.01uF 50V K
C2113NDC31HJ-201XC CAPACITOR200pF 50V J
C2114NCB31HK-104X C CAPACITOR0.1uF 50V KUT
C2115QETN1CM-107Z E CAPACITOR100uF 16V M
C2116NCB31HK-471X C CAPACITOR470pF 50V K
C2117NCB31HK-104X C CAPACITOR0.1uF 50V KB,E,EN,EV,E
C2121QETN1AM-477Z E CAPACITOR470uF 10V M
C2125NCB31HK-103X C CAPACITOR0.01uF 50V K
C2131QEZ0658-396ZE CAPACITOR39uF 50V M
C2133NCB31HK-223X C CAPACITOR0.022uF 50V K
C2153QETM1EM-228E CAPACITOR2200uF 25V M
C2155QETN1EM-337Z E CAPACITOR330uF 25V M
C2156NCB31HK-104X C CAPACITOR0.1uF 50V KB,E,EN,EV,E
C2157NCB31HK-104X C CAPACITOR0.1uF 50V KB,E,EN,EV,E
C2160NCB31HK-104X C CAPACITOR0.1uF 50V K
C2301QETN1HM-106Z E CAPACITOR10uF 50V M
C3650NCB31CK-104X C CAPACITOR0.1uF 16V K
C3651NCB31CK-104X C CAPACITOR0.1uF 16V K
C3652QETN1CM-107Z E CAPACITOR100uF 16V M
C3653QETN1VM-107Z E CAPACITOR100uF 35V M
C3654QETN1VM-107Z E CAPACITOR100uF 35V M
C3655QETN1VM-107Z E CAPACITOR100uF 35V M
C7000QERF0JM-107Z E CAPACITOR100uF 6.3V M
C7201NCB31HK-104X C CAPACITOR0.1uF 50V K
C7209NCB31CK-104X C CAPACITOR0.1uF 16V K
C7210NCB31HK-223X C CAPACITOR0.022uF 50V K
C7300NCB31HK-103X C CAPACITOR0.01uF 50V K
C7301NCB31HK-103X C CAPACITOR0.01uF 50V K
C7302QER61EM-476Z E CAPACITOR47uF 25V MUT
C8000NDC31HJ-150X C CAPACITOR15pF 50V J
C8001NDC31HJ-101XC CAPACITOR100pF 50V J
C8002NDC31HJ-150X C CAPACITOR15pF 50V J
C8004NCB31HK-104X C CAPACITOR0.1uF 50V K
C8100NDC31HJ-331X C CAPACITOR330pF 50V JB,E,EN,EV,E
C8104NCB31CK-105X C CAPACITOR1uF 16V K
C8200NDC31HJ-331X C CAPACITOR330pF 50V JB,E,EN,EV,E
C8300NCB31HK-104X C CAPACITOR0.1uF 50V K
Part No.Part NameDescriptionLocal
E,A,US,UB,
UW,UX,UG,
UN,UF,UP,U
T
E,A,UB,UF,U
P, UH
UG,UN,UT
E,A,US,UB,
UW,UX,UG,
UN,UF,UP,U
T
E
E
E
E
E,UP
E,UP
3-15
Symbol No.
Part No.Part NameDescriptionLocal
Symbol No.
Part No.Part NameDescriptionLocal
C8400NCB31HK-104X C CAPACITOR0.1uF 50V K
C8401NCB31HK-103X C CAPACITOR0.01uF 50V K
C8402NCB31CK-105X C CAPACITOR1uF 16V K
C9600NCB31HK-103X C CAPACITOR0.01uF 50V K
C9602NCB31HK-103X C CAPACITOR0.01uF 50V K
C9603NCB31HK-104X C CAPACITOR0.1uF 50V K
C9700NCB31HK-104X C CAPACITOR0.1uF 50V K
C101NCB31CK-104XC CAPACITOR0.1uF 16V K
C102NCB31CK-104XC CAPACITOR0.1uF 16V K
C103NCB31CK-104XC CAPACITOR0.1uF 16V K
C104NCB31CK-104XC CAPACITOR0.1uF 16V K
C105NEAF0JM-476XE CAPACITOR47uF 6.3V M
C106NBE20JM-226XTA E CAPACITOR22uF 6.3V M
C107NCB31CK-104XC CAPACITOR0.1uF 16V K
C108NBE20JM-226XTA E CAPACITOR22uF 6.3V M
C109NCB20JK-475XC CAPACITOR4.7uF 6.3V K
C201NDC31HJ-221XC CAPACITOR220pF 50V J
C202NDC31HJ-221XC CAPACITOR220pF 50V J
C203NCB31HK-103XC CAPACITOR0.01uF 50V K
C204NCB31CK-104XC CAPACITOR0.1uF 16V K
C205NCB31HK-271XC CAPACITOR270pF 50V K
C206NDC31HJ-151XC CAPACITOR150pF 50V J
C210NCF31AZ-105XC CAPACITOR1uF 10V Z
C211NCB31HK-223XC CAPACITOR0.022uF 50V K
C217NCB31CK-104XC CAPACITOR0.1uF 16V K
C251NCB31AK-474XC CAPACITOR0.47uF 10V K
C256NCB31CK-104XC CAPACITOR0.1uF 16V K
C257NCB31HK-822XC CAPACITOR8200pF 50V K
C258NCB31HK-153XC CAPACITOR0.015uF 50V K
C259NCB31HK-153XC CAPACITOR0.015uF 50V K
C260NCB31HK-223XC CAPACITOR0.022uF 50V K
C261NCB31HK-223XC CAPACITOR0.022uF 50V K
C262NCB31HK-223XC CAPACITOR0.022uF 50V K
C263NEAF1CM-107XE CAPACITOR100uF 16V M
C301NEAF0JM-227XE CAPACITOR220uF 6.3V M
C302NEAF0GM-476XE CAPACITOR47uF 4V M
C303NEAF0GM-476XE CAPACITOR47uF 4V M
C304NCB30JK-105XC CAPACITOR1uF 6.3V K
C305NCB31CK-104XC CAPACITOR0.1uF 16V K
C306NCB31CK-104XC CAPACITOR0.1uF 16V K
C307NCB31CK-104XC CAPACITOR0.1uF 16V K
C309NCB31CK-104XC CAPACITOR0.1uF 16V K
C310NCB31CK-104XC CAPACITOR0.1uF 16V K
C312NCB31CK-104XC CAPACITOR0.1uF 16V K
C313NCB31CK-104XC CAPACITOR0.1uF 16V K
C314NCB31CK-104XC CAPACITOR0.1uF 16V K
C315NCB31CK-104XC CAPACITOR0.1uF 16V K
C316NCB31CK-104XC CAPACITOR0.1uF 16V K
C318NCB31CK-104XC CAPACITOR0.1uF 16V K
C319NCB31CK-104XC CAPACITOR0.1uF 16V K
C320NCB31CK-104XC CAPACITOR0.1uF 16V K
C321NCB31CK-104XC CAPACITOR0.1uF 16V K
C322NCB31CK-104XC CAPACITOR0.1uF 16V K
C323NCB31CK-104XC CAPACITOR0.1uF 16V K
C324NCB30JK-105XC CAPACITOR1uF 6.3V K
C325NDC31HJ-120XC CAPACITOR12pF 50V J
Part No.Part NameDescriptionLocal
Symbol No.
C326NDC31HJ-100XC CAPACITOR10pF 50V J
C328NCB31HK-103XC CAPACITOR0.01uF 50V K
C330NCB31CK-104XC CAPACITOR0.1uF 16V K
C331NCB31CK-333XC CAPACITOR0.033uF 16V K
C332NCB31CK-104XC CAPACITOR0.1uF 16V K
C333NCB31CK-104XC CAPACITOR0.1uF 16V K
C334NCB31CK-104XC CAPACITOR0.1uF 16V K
C335NCB31CK-104XC CAPACITOR0.1uF 16V K
C337NCB31HK-183XC CAPACITOR0.018uF 50V K
C338NCB31HK-562XC CAPACITOR5600pF 50V K
C339NBE20JM-106XTA E CAPACITOR10uF 6.3V M
C340NCB30JK-105XC CAPACITOR1uF 6.3V K
C341NCB30JK-105XC CAPACITOR1uF 6.3V K
C345NCB31CK-104XC CAPACITOR0.1uF 16V K
C347NCB31CK-104XC CAPACITOR0.1uF 16V K
C348NCB31CK-104XC CAPACITOR0.1uF 16V K
C349NCB31CK-104XC CAPACITOR0.1uF 16V K
C350NCB31HK-222XC CAPACITOR2200pF 50V K
C351NCB31HK-103XC CAPACITOR0.01uF 50V K
C352NCB31HK-153XC CAPACITOR0.015uF 50V K
C353NCB31HK-561XC CAPACITOR560pF 50V K
C354NCB31HK-561XC CAPACITOR560pF 50V K
C356NCB30JK-105XC CAPACITOR1uF 6.3V K
C359NCB30JK-105XC CAPACITOR1uF 6.3V K
C370NCB31CK-104XC CAPACITOR0.1uF 16V K
C371NCF31AZ-105XC CAPACITOR1uF 10V Z
C372NCB31CK-104XC CAPACITOR0.1uF 16V K
C373NCB31CK-104XC CAPACITOR0.1uF 16V K
C374NCB31CK-104XC CAPACITOR0.1uF 16V K
C375NCB31CK-104XC CAPACITOR0.1uF 16V K
C378NCB31CK-104XC CAPACITOR0.1uF 16V K
C379NCB31CK-104XC CAPACITOR0.1uF 16V K
C380NCB21CK-105XC CAPACITOR1uF 16V K
C381NCB21AK-225XC CAPACITOR2.2uF 10V K
C383NCB31CK-104XC CAPACITOR0.1uF 16V K
C391NEAF0JM-227XE CAPACITOR220uF 6.3V M
C392NCB31CK-104XC CAPACITOR0.1uF 16V K
C393NCB31HK-103XC CAPACITOR0.01uF 50V K
C455NCB31HK-103XC CAPACITOR0.01uF 50V K
C551NCB31CK-104XC CAPACITOR0.1uF 16V K
C554NCB31CK-104XC CAPACITOR0.1uF 16V K
C555NCB31CK-104XC CAPACITOR0.1uF 16V K
C557NCB31HK-102XC CAPACITOR1000pF 50V K
C558NBE20JM-226XTA E CAPACITOR22uF 6.3V M
C559NCB31CK-104XC CAPACITOR0.1uF 16V K
C560NCB31CK-104XC CAPACITOR0.1uF 16V K
C562NCF31AZ-105XC CAPACITOR1uF 10V Z
C563NCB31CK-104XC CAPACITOR0.1uF 16V K
C564NCB31CK-104XC CAPACITOR0.1uF 16V K
C701NCB31CK-104XC CAPACITOR0.1uF 16V K
C704NEAF0JM-476XE CAPACITOR47uF 6.3V M
C706NEAF1CM-106XE CAPACITOR10uF 16V M
C707NCB31CK-104XC CAPACITOR0.1uF 16V K
C711NCB21CK-105XC CAPACITOR1uF 16V K
C712NCB31HK-103XC CAPACITOR0.01uF 50V K
C713NCB21CK-105XC CAPACITOR1uF 16V K
C740NCB31CK-104XC CAPACITOR0.1uF 16V K
C801NCB21CK-105XC CAPACITOR1uF 16V K
C802NCB21AK-225XC CAPACITOR2.2uF 10V K
C803NEAF0JM-227XE CAPACITOR220uF 6.3V M
C804NCB31HK-471XC CAPACITOR470pF 50V K
Q101or KTA1001/Y/-XTRANSISTOR
Q1022SC5383/E/-XTRANSISTOR
Q102or 2SC4617/R/-XTRANSISTOR
Q1032SA1363/EF/-XTRANSISTOR
Q103or KTA1001/Y/-XTRANSISTOR
Q1042SC5383/E/-XTRANSISTOR
Q104or 2SC4617/R/-XTRANSISTOR
Q105UNR9212J-XDIGI TRANSISTOR
Q105or RT1N241U-XDIGI TRANSISTOR
Q106INK0002AU1-XMOS FET
Q106or 2SK3019-XMOS FET
Q107INK0002AU1-XMOS FET
Q107or 2SK3019-XMOS FET
Q801RT1P441C-XDIGI TRANSISTOR
Q801or KRA104S-XDIGI TRANSISTOR
C101NCB31CK-104XC CAPACITOR0.1uF 16V K
C102NCB31CK-104XC CAPACITOR0.1uF 16V K
C103NCB31CK-104XC CAPACITOR0.1uF 16V K
C104NCB31CK-104XC CAPACITOR0.1uF 16V K
C105NEAF0JM-476XE CAPACITOR47uF 6.3V M
C106NBE20JM-226XTA E CAPACITOR22uF 6.3V M
C108NBE20JM-226XTA E CAPACITOR22uF 6.3V M
C201NDC31HJ-221XC CAPACITOR220pF 50V J
C202NDC31HJ-221XC CAPACITOR220pF 50V J
C203NCB31HK-103XC CAPACITOR0.01uF 50V K
C204NCB31CK-104XC CAPACITOR0.1uF 16V K
C205NCB31HK-271XC CAPACITOR270pF 50V K
C206NDC31HJ-151XC CAPACITOR150pF 50V J
C210NCF31AZ-105XC CAPACITOR1uF 10V Z
C211NCB31HK-223XC CAPACITOR0.022uF 50V K
C217NCB31CK-104XC CAPACITOR0.1uF 16V K
C251NCB31AK-474XC CAPACITOR0.47uF 10V K
C256NCB31CK-104XC CAPACITOR0.1uF 16V K
C257NCB31HK-822XC CAPACITOR8200pF 50V K
C258NCB31CK-153XC CAPACITOR0.015uF 16V K
C259NCB31CK-153XC CAPACITOR0.015uF 16V K
C260NCB31HK-223XC CAPACITOR0.022uF 50V K
C261NCB31HK-223XC CAPACITOR0.022uF 50V K
C262NCB31HK-223XC CAPACITOR0.022uF 50V K
C263NEAF1CM-107XE CAPACITOR100uF 16V M
C301NEAF0JM-227XE CAPACITOR220uF 6.3V M
C302NEAF0GM-476XE CAPACITOR47uF 4V M
C303NEAF0GM-476XE CAPACITOR47uF 4V M
C304NCB30JK-105XC CAPACITOR1uF 6.3V K
C305NCB31CK-104XC CAPACITOR0.1uF 16V K
C306NCB31CK-104XC CAPACITOR0.1uF 16V K
C307NCB31CK-104XC CAPACITOR0.1uF 16V K
C309NCB31CK-104XC CAPACITOR0.1uF 16V K
C310NCB31CK-104XC CAPACITOR0.1uF 16V K
C312NCB31CK-104XC CAPACITOR0.1uF 16V K
C313NCB31CK-104XC CAPACITOR0.1uF 16V K
C314NCB31CK-104XC CAPACITOR0.1uF 16V K
C315NCB31CK-104XC CAPACITOR0.1uF 16V K
C316NCB31CK-104XC CAPACITOR0.1uF 16V K
C318NCB31CK-104XC CAPACITOR0.1uF 16V K
C319NCB31CK-104XC CAPACITOR0.1uF 16V K
C320NCB31CK-104XC CAPACITOR0.1uF 16V K
C321NCB31CK-104XC CAPACITOR0.1uF 16V K
C322NCB31CK-104XC CAPACITOR0.1uF 16V K
C323NCB31CK-104XC CAPACITOR0.1uF 16V K
C324NCB30JK-105XC CAPACITOR1uF 6.3V K
C325NDC31HJ-120XC CAPACITOR12pF 50V J
C326NDC31HJ-100XC CAPACITOR10pF 50V J
C328NCB31HK-103XC CAPACITOR0.01uF 50V K
C330NCB31CK-104XC CAPACITOR0.1uF 16V K
C331NCB31CK-333XC CAPACITOR0.033uF 16V K
C332NCB31CK-104XC CAPACITOR0.1uF 16V K
C333NCB31CK-104XC CAPACITOR0.1uF 16V K
C334NCB31CK-104XC CAPACITOR0.1uF 16V K
C335NCB31CK-104XC CAPACITOR0.1uF 16V K
C337NCB31CK-183XC CAPACITOR0.018uF 16V K
C338NCB31HK-562XC CAPACITOR5600pF 50V K
C339NBE20JM-106XTA E CAPACITOR10uF 6.3V M
C340NCB30JK-105XC CAPACITOR1uF 6.3V K
C341NCB30JK-105XC CAPACITOR1uF 6.3V K
C345NCB31CK-104XC CAPACITOR0.1uF 16V K
C347NCB31CK-104XC CAPACITOR0.1uF 16V K
C348NCB31CK-104XC CAPACITOR0.1uF 16V K
C349NCB31CK-104XC CAPACITOR0.1uF 16V K
C350NCB31HK-222XC CAPACITOR2200pF 50V K
C351NCB31HK-103XC CAPACITOR0.01uF 50V K
C352NCB31CK-153XC CAPACITOR0.015uF 16V K
C353NCB31HK-561XC CAPACITOR560pF 50V K
C354NCB31HK-561XC CAPACITOR560pF 50V K
C356NCB30JK-105XC CAPACITOR1uF 6.3V K
C359NCB30JK-105XC CAPACITOR1uF 6.3V K
C370NCB31CK-104XC CAPACITOR0.1uF 16V K
C371NCF31AZ-105XC CAPACITOR1uF 10V Z
C372NCB31CK-104XC CAPACITOR0.1uF 16V K
C373NCB31CK-104XC CAPACITOR0.1uF 16V K
C374NCB31CK-104XC CAPACITOR0.1uF 16V K
C375NCB31CK-104XC CAPACITOR0.1uF 16V K
C378NCB31CK-104XC CAPACITOR0.1uF 16V K
C379NCB31CK-104XC CAPACITOR0.1uF 16V K
C380NCB21CK-105XC CAPACITOR1uF 16V K
C381NCB21AK-225XC CAPACITOR2.2uF 10V K
C383NCB31CK-104XC CAPACITOR0.1uF 16V K
C391NEAF0JM-227XE CAPACITOR220uF 6.3V M
C392NCB31CK-104XC CAPACITOR0.1uF 16V K
C393NCB31HK-103XC CAPACITOR0.01uF 50V K
C455NCB31HK-103XC CAPACITOR0.01uF 50V K
C551NCB31CK-104XC CAPACITOR0.1uF 16V K
C554NCB31CK-104XC CAPACITOR0.1uF 16V K
C555NCB31CK-104XC CAPACITOR0.1uF 16V K
C557NCB31HK-102XC CAPACITOR1000pF 50V K
C558NBE20JM-226XTA E CAPACITOR22uF 6.3V M
C559NCB31CK-104XC CAPACITOR0.1uF 16V K
C560NCB31CK-104XC CAPACITOR0.1uF 16V K
C562NCF31AZ-105XC CAPACITOR1uF 10V Z
C563NCB31CK-104XC CAPACITOR0.1uF 16V K
C564NCB31CK-104XC CAPACITOR0.1uF 16V K
C701NCB31CK-104XC CAPACITOR0.1uF 16V K
C704NEAF0JM-476XE CAPACITOR47uF 6.3V M
C706NEAF1CM-106XE CAPACITOR10uF 16V M
C707NCB31CK-104XC CAPACITOR0.1uF 16V K
C711NCB21CK-105XC CAPACITOR1uF 16V K
C712NCB31HK-103XC CAPACITOR0.01uF 50V K
C713NCB21CK-105XC CAPACITOR1uF 16V K
C740NCB31CK-104XC CAPACITOR0.1uF 16V K
C801NCB21CK-105XC CAPACITOR1uF 16V K
C802NCB21AK-225XC CAPACITOR2.2uF 10V K
C803NEAF0JM-227XE CAPACITOR220uF 6.3V M
C804NCB31HK-471XC CAPACITOR470pF 50V K
No additional / supplemental order of WARRANTY CARDs are available.
Only
UX-G500VB,E,EN,EV,EE,UP
A1,A2,A4
Only
UX-G500VUS,UB,UW,UX,UG,UN,
UH
A1,A4,A13
Only UX-G500VA
A1,A2,A4,A11
Only B
A3
Only UF
A16
Only UB
A15
Only
UX-G500VA,UB,UX
UG,UF,UP,UT,UH
P6
P5
Only
UX-G500VB,
E,EN,EV,EE,
UP,UT
A6,A7,A8,A9
P2
P4
MMM3
Only
UX-G500VUS,
UW,UN
A14A12A5
Only UX-G500UF,
UP
A17
Only
UX-G500UX-G500VUT
A1,A4
A10
A17
Only
UX-G500UP
P7
P3
Only UX-G500UF,
UP
A17
A10
P1
The parts without symbol number are not service.
3-22
Packing and Accessories
Block No. [M][3][M][M]
Symbol No.Part No.Part NameDescriptionLocal
A 1GVT0249-001AINTRUCTION BOOKENGB
A 1GVT0249-002AINTRUCTION BOOKGER FRE DUT ITAE
A 1GVT0249-003AINTRUCTION BOOKSPA SWE FIN DAN POREN
A 1GVT0249-004AINTRUCTION BOOKPOL HUN CZEEV
A 1GVT0249-005AINTRUCTION BOOKRUSEE
A 1GVT0249-006AINTRUCTION BOOKENGA,US,UB,UW,UX,UG,UN,UH
A 1GVT0249-009AINTRUCTION BOOKCHI(PEKIN)UF
A 1GVT0249-011AINTRUCTION BOOKKORUP
A 1GVT0249-013AINTRUCTION BOOKCHI(TAIWAN)UT
A 2------------WARRANTY CARDBT-54035-1B,E,EN,EV,EE
A 2------------WARRANTY CARDBT-56017-1A
A 2------------WARRANTY CARDBT-59029-1UF
A 2------------WARRANTY CARDBT-56013-1UP
A 3VNA3000-204REGIST CARDB
A 4GVT0252-001ACAUTION SHEETB,A,UW
A 4GVT0252-002ACAUTION SHEETE,EN
A 4GVT0252-003ACAUTION SHEETEV,EE
A 4GVT0252-004ACAUTION SHEETUS,UB,UX,UG,UN,UF,UP,UT,UH
A 5QQR1834-001NOISE FILTERB,E,EN,EV,EE,UP,UT
A 6QAL0014-003AM LOOP ANTB,E,EN,EV,EE
A 6QAL1123-001AM LOOP ANTA,US,UB,UW,UX,UG,UN,UF,UP,UT,UH
A 7QAL0457-001ANT.WIRE
A 8RM-SUXG500VRREMOCONB,E,EN,EV,EE
A 8RM-SUXG500VUREMOCONA,US,UB,UW,UX,UG,UN,UF,UP,UT,UH
A 9------------BATTERY(x2)
A 10SPUXG500V-SPBOXSPK WITH BOX(x2)
A 11------------WARRANTY CARDBT-56016-1A
A 12QAM0944-001PIN CABLEA,US,UB,UW,UX,UG,UN,UF,UP,UT,UH
A 13GVT0249-008AINTRUCTION BOOKCHI(PEKIN)US,UB,UN
A 13GVT0249-007AINTRUCTION BOOKSPA PORUW
A 13GVT0249-010AINTRUCTION BOOKARA PERUX,UG
A 13GVT0249-012AINTRUCTION BOOKTHAUH
A 14QAM0112-002CONVERSION PLUGUS,UW,UN
A 15GV30024-068AUB SHEETUB
A 16BT-59021-9SVC CENTER LISTUF
A 17LV44927-201ALABEL(x2)UF
A 17LV43644-001ALABEL(x4)UP
P 1GV31147-001ACARTON BOXB,E,EN,EV
P 1GV31147-004ACARTON BOXEE
P 1GV31147-002ACARTON BOXA,US,UB,UW,UX,UG,UN,UP,UT,UH
P 1GV31147-003ACARTON BOXUF
P 2GV10409-001ACUSHION TOP
P 3GV10410-001ACUSHION BOTTOM
P 4GV40437-007ACLOTH
P 5QPC05006515PBPOLY BAG50cm x 65cm
P 6QPC02503515PBPOLY BAG25cm x 35cm
P 7QPC02503515PBPOLY BAG25cm x 35cm
3-23
SCHEMATIC DIAGRAMS
MICRO COMPONENT SYSTEM
UX-G500VB,UX-G500VE,UX-G500VEN,UX-G500VEV
UX-G500VEE,UX-G500VA,UX-G500VUS,UX-G500VUB
UX-G500VUW,UX-G500VUX,UX-G500VUG,UX-G500VUN
UX-G500VUF,UX-G500VUP,UX-G500VUT,UX-G500VUH
DVD-ROM No.SML2008Q3
SUPER VIDEO
Lead free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade)
Lead free solder used in the board (material : Sn-Cu, melting point : 230 Centigrade)
Contents
Block diagrams
Standard schematic diagrams
Printed circuit boards
For europe except EV version
COPYRIGHT 2008 Victor Company of Japan, Limited.
For asia and EV version
2-1
2-2
2-12 to 14
No.MB674SCH<Rev.00 3>
2008/10
In regard with component parts appearing on the silk-screen printed side (parts side) of the PWB diagrams, the
parts that are printed over with black such as the resistor ( ), diode ( ) and ICP ( ) or identified by the " "
mark nearby are critical for safety.