JVC LT-32D50SJ, LT-26D50BJ, LT-32D50BJ, LT-26D50SJ User Manual

LT-32D50BJ LT-26D50BJ LT-32D50SJ LT-26D50SJ
DynaPix LCD IDTV with D.I.S.T.
Trade Mark of the DVB Digital Video Broadcasting Project (1991 to 1996) Number: 3249
INSTRUCTIONS
LT-32/26D50BJ/SJ / LCT1703-001B-U / ENGLISH
Warning
DO NOT cut off the mains plug from this equipment.
for the power points in your home or the cable is too short to reach a power point, then obtain an appropriate safety approved extension lead or adaptor or consult your dealer.
If nonetheless the mains plug is cut off, remove the fuse and dispose of the plug immediately, to avoid a possible shock hazard by inadvertent connection to the mains supply.
If a new mains plug has to be fitted, then follow the instruction given below:
Important
Do not make any connection to the larger terminal which is marked with the letter E or
by the safety earth symbol or coloured green or green-and-yellow.
The wires in the mains lead on this product are coloured in accordance with the following code: Blue: Neutral Brown: Live
If the plug fitted is not suitable
As these colours may not correspond with the coloured marking identifying the terminals in your plug proceed as follows:
The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black.
The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.
When replacing the fuse, use only a correctly rated approved type and always re-fit the fuse cover.
If in doubt — consult a competent
electrician.
How to replace the fuse
Open the fuse compartment with a blade screwdriver, and replace the fuse.
Fuse
Guidelines for safe operation
This equipment has been designed and manufactured to comply with international safety standards. However, as with any electrical appliance, care must be taken to ensure optimal results and operational safety.
• Before attempting to use this equipment, read the operating instructions thoroughly.
• Ensure that all electrical connections (including the mains plug, extension leads, etc.) have been made in accordance with the manufacturer’s instructions.
• If ever in doubt about the installation, operation or safety of this equipment, consult your dealer.
• Handle all glass panels or covers with care.
• Never operate this equipment if it appears damaged or operates abnormally. Turn the power off, disconnect the main power plug and consult your dealer.
• Never remove any affixed panels or covers. Doing so may result in electrical shock.
• Never leave this equipment operating unattended unless otherwise specifically stated that it is designed to do so or in standby mode. Only use the designated power switch to turn off the power and ensure that all potential users are instructed how to do so. Make special arrangements for infirm or handicapped persons.
• Never watch TV while operating a motor vehicle. It is illegal to watch TV while driving.
• Never listen to headphones at high volume. Doing so may damage your hearing.
• Never obstruct the ventilation of this equipment. Doing so may cause overheating and result in a malfunction or damage.
• Never use makeshift stands or attempt to affix legs with wood screws. When using a manufacturer’s approved stand or legs, use only the fixtures provided and follow the installation instructions.
• Never allow this equipment to be exposed to rain or moisture.
• Never allow anyone, especially children, to insert anything into an opening in the case. Doing so may result in a fatal electrical shock.
• Never guess or take chances with electrical equipment of any kind. It is better to be safe than sorry.
2
LT-32/26D50BJ/SJ / LCT1703-001B-U / ENGLISH
Thank you for buying this JVC LCD flat television. To make sure you understand how to use your new TV, please read this manual thoroughly before you begin. (“LCD” stands for Liquid Crystal Display.)
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.
WARNING: WHEN PUTTING THE TV DOWN, DO SO SLOWLY AND
CAREFULLY ONTO A FLAT SURFACE.
WARNING
• Fingers may be trapped under the TV causing injuries. Hold the TV at the bottom in the middle, and do not allow it to tilt up or down.
WARNING
• The TV may fall causing injuries. Hold the bottom of the stand with your hand and tilt the TV up and down.
• Do not allow children to hang from the TV, place their elbows on the TV or lean against the TV. Doing so may cause the TV to fall over and lead to injuries.
CAUTION
• The TV screen may be damaged if the TV is carried as shown in the diagram below. The TV should always be carried by two people.
3
LT-32/26D50BJ/SJ / LCT1703-001B-U / ENGLISH
Thank you for buying this JVC colour television. To make sure you understand how to use your new TV, please read this manual thoroughly before you begin.
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.
CAUTION:
• Operate only from the power source specified (AC 110 – 240 V, 50/60 Hz) on the unit.
• Avoid damaging the AC plug and power cord.
• When you are not using this unit for a long period of time, it is recommended that you disconnect the power cord from the main outlet.
Pixel defects
LCDs use collections of fine points (“pixels”) to display images. While there is no problem with more than 99.99% of these pixels, please understand that a very small number of pixels may not light, or may light all the time.
Distance recommendations
Avoid improper installation and never position the unit where good ventilation is impossible. When installing this TV, distance recommendations must be maintained between the set and the wall, as well as inside a tightly enclosed area or piece of furniture. Keep to the minimum distance guidelines shown for safe operation.
150 mm 150 mm
200 mm 200 mm
50 mm
Failure to heed the following precautions may result in damage to the TV or remote control.
DO NOT block the TV’s ventilation openings or holes.
(If the ventilation openings or holes are blocked by a newspaper or cloth, etc., the heat may not be able to get out.)
DO NOT place anything on top of the TV.
(such as cosmetics or medicines, flower vases, potted plants, cups, etc.)
DO NOT allow objects or liquid into the cabinet openings.
(If water or liquid is allowed to enter this equipment, fire or electric shock may be caused.)
DO NOT place any naked flame sources, such as lighted candles, on the TV.
The surface of the TV screen is easily damaged. Be very careful with it when handling the TV. Should the TV screen become soiled, wipe it with a soft dry cloth. Never rub it forcefully. Never use any cleaner or detergent on it.
In the event of a fault, unplug the unit and call a service technician. Do not attempt to repair it yourself or remove the rear cover.
4
LT-32/26D50BJ/SJ / LCT1703-001B-U / ENGLISH
D.I.S.T. demonstration
To start the D.I.S.T. demonstration: Press the H button to display the menu bar. Then press the yellow button. A picture split in two (D.I.S.T. turned on and D.I.S.T. turned off) will appear on the screen.
To quit the D.I.S.T. demonstration: Press the yellow button,
TV/DTV button, p p buttons or any of the number buttons.
NOTE:
Due to static electricity, the TV may be covered with dust. If this happens, wipe the TV with a soft cloth being careful not to scratch the TV.
Digital terrestrial broadcasting (DVB-T) service area
Although this TV can receive both Digital terrestrial broadcasting (DVB-T) and Analogue terrestrial broadcasting, depending on the area in which you live, you may not be able to receive Digital terrestrial broadcasting (DVB-T). For details of the Digital terrestrial broadcasting (DVB-T) service area, refer to the FREEVIEW website etc.
Cleaning the screen
The screen is coated with a special thin film to reduce reflection. If this film is damaged, uneven colours, discolouration, scratches, and other problems that cannot be repaired may occur. Pay attention to the following when handling the screen.
• Do not use glue or adhesive tape on the screen.
• Do not write on the screen.
• Do not allow the screen to come in contact with any hard objects.
• Do not allow condensation to form on the screen.
• Do not use alcohol, thinner, benzene or other solvents on the screen.
• Do not rub the screen hard.
5
LT-32/26D50BJ/SJ / LCT1703-001B-U / ENGLISH
CONTENTS
Setting up your TV ...................................7
Installation.................................................. 7
Using the stand .......................................... 7
Removing the terminal covers ................... 8
Connecting the aerial................................. 9
Connecting the power cord to the AC
outlet..................................................... 10
Putting the batteries into the remote
control................................................... 10
Initial settings ........................................... 10
T-V LINK functions................................... 13
Basic operations (TV) ............................15
Turn the TV on from standby mode ......... 15
Choose a TV channel .............................. 15
Watching images from external devices
Adjust the volume .................................... 16
Using the Menu........................................ 16
.... 16
Basic operations (Remote control) ......17
Turn the TV on or off from standby mode Choose a TV channel and watch images
from external devices ........................... 18
Adjust the volume .................................... 19
ZOOM function......................................... 19
3D SOUND function ................................. 21
... 18
Operation while watching DTV .............22
Information function ................................. 22
Using the “Multi-picture” function ............. 22
Using the Electronic Programme Guide
(EPG) ................................................... 23
Displaying the Subtitles............................ 25
Digital Teletext function ........................26
Operation with the DTV menu...............27
Displaying the DTV menu ........................ 27
Timers (DTV Timer Recording) ................ 27
Configuration............................................ 30
Edit PR List .............................................. 32
Installation................................................ 34
Common Interface ................................... 35
Operation while watching
analogue TV ........................................36
Information function ................................. 36
Using the “Freeze” function...................... 37
Using the “Multi-picture” function ............. 37
Favourite channel function....................... 38
Analogue teletext function....................40
Basic operation ........................................ 40
Using the List Mode ................................. 41
Hold.......................................................... 41
Sub-page ................................................. 41
Reveal...................................................... 41
Size .......................................................... 42
Index ........................................................ 42
Cancel...................................................... 42
Setting the TV......................................... 43
Basic operation ........................................ 43
PICTURE menu ......................................45
PICTURE MODE...................................... 45
BRIGHT-1 ................................................ 45
CONTRAST ............................................. 45
BRIGHT-2 ................................................ 45
SHARP..................................................... 45
COLOUR.................................................. 45
HUE.......................................................... 45
COLOUR TEMP....................................... 45
FEATURES .............................................. 46
SOUND menu ......................................... 49
STEREO / I • II ......................................... 49
BASS........................................................ 49
TREBLE ................................................... 49
BALANCE ................................................ 49
3D SOUND............................................... 49
A.H.B. (Active Hyper Bass) ...................... 49
BBE .......................................................... 49
FEATURES menu................................... 50
SLEEP TIMER ......................................... 50
CHILD LOCK............................................ 50
APPEARANCE......................................... 51
BLUE BACK ............................................. 52
FAVOURITE SETTING ............................ 52
SET UP menu ......................................... 53
AUTO PROGRAM (Analogue)................. 53
EDIT/MANUAL (Analogue) ...................... 53
DECODER (EXT-2).................................. 58
COMPONENT AUTO SELECT ................ 58
EXT SETTING.......................................... 59
Displaying a computer screen.............. 62
Connecting to the computer ..................... 62
Watching images from a computer ..........62
Table of signals for each type of
computer............................................... 62
Additional preparation ..........................63
Connecting external equipment ...............63
Operating a JVC brand VCR or DVD
player.................................................... 66
Troubleshooting ....................................67
Specifications ........................................70
6
LT-32/26D50BJ/SJ / LCT1703-001B-U / ENGLISH

Setting up your TV

• When you install the TV on the wall, only use a JVC wall mounting unit (optional) which is designed for this TV.
• Make sure that the TV is installed on the wall by a skilled installer.

Installation

Cautions for installation
• Install the TV in a corner on a wall or on the floor so as to keep cords out of the way.
• The TV will generate a slight amount of heat during operation. Ensure that sufficient space is available around the TV to allow satisfactory cooling. See “Distance recommendations” on page 4.

Using the stand

This TV comes with a table top stand already attached.
This stand can be used to adjust the direction of the TV screen 5° up, 10° down, and 20° to the left or right.
Tilt the TV up and down:
While holding the bottom of the stand with one hand, use your other hand to hold the middle of the top of the TV and slowly tilt the TV up and down.
• As a safety measure, the stand needs constructed so that it requires a certain amount of force to tilt the TV.
Rotate the TV to the left and right:
While holding the bottom of the stand with one hand, use your other hand to hold the edge of the panel and slowly adjust the direction of the TV screen.
7
LT-32/26D50BJ/SJ / LCT1703-001B-U / ENGLISH
Setting up your TV
Cable holder
A cable holder which is used to keep the connection cables tidy is attached to the back of the stand. Gently squeeze the left and right of the cable holder and pull it to remove it from the stand. After putting the cables in the cable holder, attach it to the back of the stand again.
cable holder

Removing the terminal covers

There are connection terminals behind the covers on the left and right of the rear of the TV. Remove these two covers before connecting an antenna or VCR.
Remove the covers by removing the hooks. When replacing the covers, place the side of the covers against the TV and insert the hooks.
• Leave the covers off if they do not fit properly. Do not force to replace the covers. Doing so may cause damage to the connection cables and the covers.
8
LT-32/26D50BJ/SJ / LCT1703-001B-U / ENGLISH
Setting up your TV

Connecting the aerial

For viewing digital terrestrial signals only, connect the antenna directly to the digital aerial socket.
• The connecting cables are not provided.
• For further details, refer to the manuals provided with the devices to be connected.
Caution
• Turn off all the equipment including the TV before connecting anything.
If you connect via a device with an
antenna terminal such as a VCR, follow A B C in the diagram opposite.
If you connect the antenna
directly to the TV, follow 1.
• For viewing digital terrestrial and analogue TV signals, using a two-way signal splitter, connect one output to the digital aerial socket, the other output to the analogue aerial socket.
Without terminal covers
Aerial
It is possible to view analogue TV & teletext by using the VCR tuner, this can be achieve by switching to the EXT input to which the 21 pin SCART cable linking the TV and VCR is connected.
• To connect more equipment, please see “Connecting external equipment” on page 63.
• To connect additional audio equipment, see “Connecting speakers/amplifier” on page 66.
• When receiving Digital terrestrial broadcasting (DVB-T), reception can suddenly be lost if the signal becomes weak. Use a correctly installed high­performance antenna.
• When connecting via a device with an antenna terminal such as a VCR, depending on the connection method, the signal may be weakened. If this happens, use a booster to increase the signal strength.
• In areas with a lot of radio communication such as near ports or airports, noise may be introduced into the picture or sound. In such cases, reception may be improved by using a high-performance antenna.
• Read the instruction manual of the devices which you connect to the TV.
To digital
aerial socket
21-pin SCART
Cable
VCR
AV IN/OUT
Terminal
75-ohm Coaxial
Cable
To Aerial
Input
To Aerial
Output
75-ohm Coaxial
Cable
75-ohm Coaxial
Cable
9
LT-32/26D50BJ/SJ / LCT1703-001B-U / ENGLISH
LT-32&26D50BJSJ_Eng.book Page 10 Thursday, October 7, 2004 4:42 PM
Setting up your TV

Connecting the power cord to the AC outlet

Insert the AC plug on the power cord from the TV into an AC outlet. The TV will enter standby mode.
Caution
• Operate only from the power source specified (AC 110 – 240 V, 50/60 Hz) on the unit.
• Remove the AC plug from the outlet to completely disconnect the TV from the power supply.

Putting the batteries into the remote control

Use two AA/R6 dry cell batteries. Insert the batteries from the - end, making sure the + and - polarities are correct.
• Follow the warnings printed on the batteries.
• Battery life is about six months to one year, depending on how much you use the remote control.
• The batteries we supply are only for setting up and testing your TV, please replace them as soon as you need to.
• If the remote control does not work properly, replace the batteries.

Initial settings

When the TV is first turned on, it goes into the initial settings mode, and you will see the JVC logo. Follow the instructions on the screen display to make the initial settings.
# button
VCR/TV/DVD switch
Blue button
7 buttons
1 Make sure to set the VCR/TV/DVD
switch on the remote control to the TV position
• You cannot turn the TV on when the VCR/TV/DVD switch is set to the VCR or DVD position.
2 Press the # button on the remote
control
The TV turns on from standby mode and the JVC logo is displayed.
• Check that the AC plug on the power cord from the TV is connected to AC outlet.
Remote control sensor
10
Power lamp
LT-32/26D50BJ/SJ / LCT1703-001B-U / ENGLISH
LT-32&26D50BJSJ_Eng.book Page 11 Thursday, October 7, 2004 4:42 PM
Setting up your TV
• If the JVC logo does not appear this is because your TV has already been turned on for the first time: Perform the initial settings with “Installation” (see page 34) in the DTV menu and “AUTO PROGRAM (Analogue)” (see page 53) in the SET UP menu.
3 Press the a button
The Digital terrestrial broadcasting (DVB-T) Automatic Search starts. The Digital terrestrial broadcasting (DVB-T) channels which can be received are automatically registered.
• In Ireland and some parts of the UK, Digital terrestrial broadcasting (DVB-T) cannot be received. If you are in these areas, continue to step 4.
Installation > Automatic Search
Channels: BBC ONE
BBC TWO BBC THREE BBC NEWS 24 BBCi CBBC Channel
UHF 100%
Cancel, go to Installation Cancel, go to DTV
BACK
D0201-EN
CH:68
MENU
When the Automatic Search has finished, the EDIT PR LIST menu appears
1 BBC ONE
Select Delete Edit Name Lock Favourites
Select function Watch PR
D0202-EN
1. BBC ONE
2. BBC TWO
7. BBC THREE
30. CBBC Channel
40. BBC NEWS 24
51. BBCi
Select PR
EDIT PR LIST
OK
• If you want to, you can now edit the programme numbers (PR) using the EDIT PR LIST function. For details, see “Edit PR List” on page 32.
• If you do not want to edit programme numbers (PR), go to the next step.
More..
4 Press the H button
The COUNTRY menu appears.
> COUNTRY
OK
D0003-EK
START
• If you are not connecting the aerial cable to the analogue aerial socket, press H button to complete the initial setting. Then press
TV/DTV
button to watch digital broadcasting.
5 Press the 5 button to choose the
country, and then press the blue button
The Analogue terrestrial broadcasting AUTO PROGRAM starts. The AUTO PROGRAM menu appears and received TV channels are automatically stored in the programme numbers (PR).
>> AUTO PROGRAM
CH 28
14%
OK
D0004-EN
• To cancel the AUTO PROGRAM function: Press the
TV/DTV button.
After the AUTO PROGRAM has finished, the EDIT menu appears
> EDIT
D0038-EK
PR ID AV 01 02 03 04 05 06 07 08 09
OK
MOVE
BBC1 BBC2 ITV CH4 CH5
CH
CH 21 CH 22 CH 23 CH 24 CH 25 CH 26 CH 27 CH 28 CH 29
INSERT
ID
MANUAL
DELETE
11
LT-32/26D50BJ/SJ / LCT1703-001B-U / ENGLISH
LT-32&26D50BJSJ_Eng.book Page 12 Thursday, October 7, 2004 4:42 PM
Setting up your TV
• If you want to, you can now edit the programme numbers (PR) using the EDIT/MANUAL function. For details, see “EDIT/MANUAL (Analogue)” on page 53.
• If you do not want to edit programme numbers (PR), go to the next step.
6 Press the a button to display the
T-V LINK menu
T-V LINK
DOWNLOAD TV RECORDING DEVICE
OK
D0005-EN
EXIT
• If you are not connecting the aerial cable to analogue aerial socket, or do not have a T-V LINK compatible VCR connected:
Press the TV/DTV button to exit the T-V LINK menu. The T-V LINK menu disappears.
If you have a T-V LINK compatible VCR connected to the EXT-2 terminal:
Follow the operating procedure “Downloading the data to VCR” on page 12 to transmit the Programme number (PR) data.
Now, the initial settings are complete, and you can watch the TV
When the COUNTRY setting is
UNITED KINGDOM:
The Analogue terrestrial broadcasting channels BBC1, BBC2, ITV, Channel 4 and Channel 5 are automatically set to the programme numbers PR1 to PR5. If the TV doesn’t receive one of these TV channels, that programme number (PR) will not be set. Programme number PR6 is not normally set.
When the COUNTRY setting is
IRELAND:
If a TV channel you want to view is not set to a programme number (PR), you can set it manually. To set an Analogue terrestrial broadcasting channel, see “EDIT/MANUAL (Analogue)” on page 53.
12
• The AUTO PROGRAM function does not set the programme number PR 0 (AV) for your video cassette recorder. You will need to set this using the MANUAL function.
For users in the UK:
If you have any problems setting up your new TV, please call the Helpline on 0870 330 5000.
For users in the Republic of Ireland:
If you have any problems setting up your new TV, please call the Helpline on 1890-582500.
Downloading the data to VCR
You can transmit to the latest Analogue terrestrial broadcasting Programme numbers (PR) data to a VCR with the T-V LINK function.
Caution
If the TV’s analogue tuner is not being used, ie. there is no antenna cable connected to the analogue aerial socket, take care not to commence T-V LINK as the VCR programme memory will be erased.
• This only works when a T-V LINK compatible VCR is connected to the EXT-2 terminal.
• This only works when the T-V LINK menu is being displayed.
T-V LINK
DOWNLOAD TV RECORDING DEVICE
OK
D0005-EN
1 Turn on the VCR
2 Press the a button
The data transmission begins.
TV RECORDING DEVICE
TRANSFER. . . . .
D0037
The T-V LINK menu disappears once the data transmission ends.
EXIT
-EN
LT-32/26D50BJ/SJ / LCT1703-001B-U / ENGLISH
LT-32&26D50BJSJ_Eng.book Page 13 Thursday, October 7, 2004 4:42 PM
Setting up your TV
When the T-V LINK menu is changed over to another menu:
The TV has finished its menu. This new menu is operated from the VCR. See the VCR instruction manual for what to do next.
If “FEATURE NOT AVAILABLE” appears at the T-V LINK menu:
Check the following three items. Then press the 2 button to retry data transmission.
• Has a T-V LINK compatible VCR been connected to the EXT-2 terminal?
• Has the VCR power been turned on?
• Does the SCART cable that is connected to the EXT-2 terminal to T­V LINK compatible VCR have all its proper connections?

T-V LINK functions

When you have a T-V LINK compatible VCR connected to the EXT-2 Terminal on the TV, it is easier to set up the VCR and to view videos. T-V LINK uses the following features:
To use T-V LINK functions:
A “T-V LINK compatible VCR” means a JVC video cassette recorder with the T-V LINK logo, or with one of the following logos. However, these VCRs may support some or all of the features described earlier. For details, see your VCR instruction manual.
“Q-LINK” (a trademark of Panasonic Corporation) “Data Logic” (a trademark of Metz Corporation) “Easy Link” (a trademark of Phillips Corporation) “Megalogic” (a trademark of Grundig Corporation) “SMARTLINK” (a trademark of Sony Corporation).
Pre-set download
The VCR will automatically download the registered data on the TV Analogue terrestrial broadcasting channels from the TV. This means you do not need to set up the program channels on your VCR manually. The preset download function automatically begins when the initial setting is complete or whenever you carry out the AUTO PROGRAM or EDIT/MANUAL functions.
You can also carry out this function using your VCR controls.
When “FEATURE NOT AVAILABLE” is displayed:
If “FEATURE NOT AVAILABLE” is displayed, the download was not performed correctly. Before trying to download again, check that:
• the VCR power is turned on
• the VCR is T-V LINK compatible
• the VCR is connected to the EXT-2 terminal
• the SCART cable is fully wired.
Direct Rec
“What You See Is What You Record”
You can easily record to VCR the images that you are watching on the TV.
For details, read the manual for your VCR. Use your VCR controls. “DEVICE IS RECORDING” is displayed.
You cannot carry out Direct Rec using your TV’s control. Generally, the VCR cannot record a TV channel that it cannot receive properly on its own tuner, even if you can view that TV channel on the TV. However, some VCRs can record a TV channel by using the TV’s output if that channel can be viewed on the TV. For details, see your VCR instruction manual.
13
LT-32/26D50BJ/SJ / LCT1703-001B-U / ENGLISH
LT-32&26D50BJSJ_Eng.book Page 14 Thursday, October 7, 2004 4:42 PM
Setting up your TV
Do not turn the TV off in the following cases.
• when recording images from an external device connected to the TV (for example a camcorder)
• when recording a TV channel after it has been unscrambled on a decoder
• when recording a TV channel by using the TV’s output because the VCR’s own tuner cannot properly receive that channel.
• when recording Digital terrestrial broadcasting (DVB-T).
If you change channels or perform other operations while a Digital terrestrial broadcasting (DVB-T) channel is being recorded, a window appears asking whether to stop the recording.
Press the a button to stop the recording, or the
TV/DTV button to
continue the recording.
When the VCR is not ready, the following messages are displayed.
ERROR MESSAGE
NO RECORDING
NO RECORDING POSSIBLE
NO RECORDING, MEDIA PROBLEM
NO RECORDING, DEVICE BUSY
Cause and countermeasure
The VCR is not able to record. Check the VCR.
The TV input is set to EXT-4 or PC. Since the EXT-4 picture or PC picture cannot be output to EXT-2, DIRECT REC is not possible.
The RECORDING DEVICE is not ready to record. Check the VCR tape.
The RECORDING DEVICE cannot record as it is recording or playing. Check the VCR.
Refer to the VCR instruction manual.
14
LT-32/26D50BJ/SJ / LCT1703-001B-U / ENGLISH
LT-32&26D50BJSJ_Eng.book Page 15 Thursday, October 7, 2004 4:42 PM

Basic operations (TV)

3
4
5
6
7
8
1
2

Turn the TV on from standby mode

Press the A button or the P p buttons to turn the TV on from standby mode.
When the TV is turned on, the power lamp lights green.
To turn the TV off:
Press the A button again. The power lamp goes off.
Caution
•The A button on the TV does not fully
isolate the TV from the AC supply. If you are not going to use the TV for a long period, be sure to disconnect the AC plug from the AC socket.
Power lamp condition
Status
On
Standby
normal Green
when timer is set Green
3 minutes before timer starts
while timer recording in progress
normal does not light
when timer is set does not light
3 minutes before timer starts
while timer recording in progress
Power lamp condition
Flashing in green
Green
Flashing in Red
Orange
1 Remote control sensor 2 Power lamp 3 TV/AV button 4 MENU/OK button 5 P p buttons 6 r (Volume) q buttons 7 A (Stand by) button 8 Headphone jack (mini jack)

Choose a TV channel

Press the P p buttons to choose a programme number (PR) or an EXT terminal
The EXT terminal cannot be chosen when watching Digital terrestrial broadcasting (DVB-T).
15
LT-32/26D50BJ/SJ / LCT1703-001B-U / ENGLISH
LT-32&26D50BJSJ_Eng.book Page 16 Thursday, October 7, 2004 4:42 PM
Basic operations (TV)

Watching images from external devices

Press the TV/AV buttons to choose an EXT terminal
TV mode EXT modes
Analogue terrestrial broadcasting
Digital terrestrial broadcasting (DVB-T)
EXT-1
E1 or S1 S2E2
PC
E3
EXT-2
or
EXT-3
or
EXT-4
E4
S3

Adjust the volume

1 Press the r (Volume) button once
The volume level indicator appears.
2 Press the q buttons while the
volume level indicator is displayed

Using the Menu

Use the MENU/OK button
Refer to “Setting the TV” (see page 43) for details of using the menu.
If the Digital terrestrial broadcasting (DVB-T) picture is unnatural:
Press the TV/AV button and MENU/OK button at the same time. The power will turn off and then on again, after which the picture may appear natural again.
16
LT-32/26D50BJ/SJ / LCT1703-001B-U / ENGLISH
LT-32&26D50BJSJ_Eng.book Page 17 Thursday, October 7, 2004 4:42 PM

Basic operations (Remote control)

1 Muting button
1
2
3
4
5
6 7
8
!
@
#
$
%
^
&
2 Number buttons 3 Information button 4 Colour button
TV/DTV button
5 6 7 buttons 7 g (Text) button 8 p p buttons 9 VCR/DVD/Teletext control buttons 0 d (Favourite) button
- p buttons = c button ~ 3 button ! # (Standby) button @ VCR/TV/DVD switch # G button $ H button % a button ^ b button & r (Volume) q buttons
GUIDE button
* ( SUBTITLE button ) X (Multi) button _ f/c (Freeze/Select) button
9 0
-
= ~
* (
) _
17
LT-32/26D50BJ/SJ / LCT1703-001B-U / ENGLISH
LT-32&26D50BJSJ_Eng.book Page 18 Thursday, October 7, 2004 4:42 PM
Basic operations (Remote control)

Turn the TV on or off from standby mode

Press the # (standby) button to turn the TV on or off.
When the TV is turned on, the power lamp lights green.
• The power can be turned on by pressing the
TV/DTV button, p p buttons or
Number buttons.
To turn the TV on or off, set the VCR/TV/ DVD switch on the remote control to the TV position and press the # button. If the VCR/TV/DVD switch on the remote control is set to a position other than TV, the TV will not be turned on or off even if the # button is pressed.

Choose a TV channel and watch images from external devices

Switching between Digital
terrestrial broadcasting (DVB-T) and Analogue terrestrial broadcasting.
Press the TV/DTV button.
The broadcasting is switched every time the button is pressed.
Use the number buttons:
Enter the programme number (PR) of the channel using the number buttons.
Example:
•PR 6 press 6
• PR 12 press 1 and 2
• PR 123 press 1, 2 and 3
Use the p p buttons:
Press the p p buttons to choose the programme number (PR) you want.
• For Digital terrestrial broadcasting (DVB­T), if the FAVOURITE setting in the “Edit PR List” (see page 32) has been set, only that programme number (PR) can be chosen.
• For Analogue terrestrial broadcasting, an EXT terminal can also be chosen.
Use the AV button:
Press the AV button to choose an EXT terminal.
TV mode EXT modes
Analogue terrestrial broadcasting
Digital terrestrial broadcasting (DVB-T)
EXT-1
E1 or S1 S2E2
PC
• You can choose a video input signal from the S-VIDEO signal (Y/C signal) and regular video signal (composite signal). For details, see “S-IN (S-VIDEO input)” on page 59.
• If you do not have a clear picture or no colour appears, change the colour system manually. See “COLOUR SYSTEM” on page 48.
• If you choose an EXT terminal with no input signal, the EXT terminal number becomes fixed on the screen.
• This TV set has a function which can automatically change over the input according to a special signal output from an external device. (The EXT-3 terminal does not support this function.) – When EXT-4 is chosen, motion differs
according to the “COMPONENT AUTO SELECT” setting in the SET UP menu. For details, see “COMPONENT AUTO SELECT” on page 58.
E3
EXT-2
or
EXT-3
or
EXT-4
E4
S3
18
LT-32/26D50BJ/SJ / LCT1703-001B-U / ENGLISH
LT-32&26D50BJSJ_Eng.book Page 19 Thursday, October 7, 2004 4:42 PM
Basic operations (Remote control)
• Since this TV is designed to make full use of the resolution of the original video source, the motion may appear unnatural when the video source is input with progressive-scanning component signals. If this happens, change the output setting of the connected device to interlace­scanning component signal output. See the instructions that came with the device for more information.
• The PC sound is the same as the EXT-3 sound.
To return to a TV channel:
Press the
TV/DTV button, the p p
buttons or the number buttons.
To use the programme number PR 0 (AV):
When the TV and VCR are connected only by the aerial cable, choosing the programme number PR 0 (AV) allows you to view images from the VCR. Set the VCR RF channel to the programme number PR 0 (AV) manually. For details, see “EDIT/ MANUAL (Analogue)” on page 53. Pressing the G button changes the choice as follows:
TV mode EXT modes
Analogue terrestrial broadcasting
Digital terrestrial broadcasting (DVB-T)
EXT-1PR 0
E1 or S1
PC
E3
EXT-2
or
EXT-3
or
EXT-4
E4
S2E2
S3
• The VCR sends its playback image along the aerial cable as an RF (radio frequency) signal.
• Also see your VCR instruction manual.

Adjust the volume

Press the r q buttons to adjust the volume.
The volume level indicator appears and the volume changes as you press the r q buttons.
Muting the sound
Press the l (muting) button to turn off the sound.
Pressing the l (muting) button again restores the previous volume level.

ZOOM function

You can change the screen size according to the picture aspect ratio. Choose the optimum one from the following ZOOM modes.
AUTO:
When a WSS (Wide Screen Signalling) signal, which shows the aspect ratio of the picture, is included in the broadcast signal or the signal from an external device, the TV automatically changes the ZOOM mode to 16:9 ZOOM mode or FULL mode according to the WSS signal. If a WSS signal is not included, the picture is displayed according to the ZOOM mode set with the 4:3 AUTO ASPECT function.
• For details of the 4:3 AUTO ASPECT function, see “4:3 AUTO ASPECT” on page 48.
• When the AUTO (WSS) mode does not function correctly due to poor WSS signal quality or when you want to change the ZOOM mode, press the c button and change to another ZOOM mode.
• When watching a 16:9 FULL programme with Digital terrestrial broadcasting (DVB-T), the aspect ratio is FULL.
REGULAR:
Use to view a normal picture (4:3 aspect ratio) as this is its original shape.
19
LT-32/26D50BJ/SJ / LCT1703-001B-U / ENGLISH
LT-32&26D50BJSJ_Eng.book Page 20 Thursday, October 7, 2004 4:42 PM
Basic operations (Remote control)
PANORAMIC:
This stretches the left and right sides of a normal picture (4:3 aspect ratio) to fill the screen, without making the picture appear unnatural.
This mode may result in information such as headlines or rolling text at the very top or bottom of the screen not being fully viewable on some programmes. In such cases the picture can be moved up or down using 6 keys, alternatively switch to FULL mode.
14:9 ZOOM:
This zooms up the wide picture (14:9 aspect ratio) to the upper and lower limits of the screen.
16:9 ZOOM:
This zooms up the wide picture (16:9 aspect ratio) to the full screen.
16:9 ZOOM SUBTITLE:
This zooms up the wide picture (16:9 aspect ratio) with subtitles to the full screen.
FULL:
This uniformly stretches the left and right sides of a normal picture (4:3 aspect ratio) to fill the wide TV screen.
• For 16:9 aspect ratio pictures that have been squeezed into a normal picture (4:3 aspect ratio), use the FULL mode to restore the picture to its original shape.
• When you use this TV’s output signal to record a Digital terrestrial broadcasting (DVB-T) 16:9 broadcast, it will be recorded with its picture squeezed into a 4:3 aspect ratio picture. Use the FULL mode to restore the picture to its original shape when playing the recording.
Choose the ZOOM mode
1 Press the c button to display
the ZOOM menu
ZOOM
AUTO REGULAR PANORAMIC 14:9 ZOOM 16:9 ZOOM 16:9 ZOOM SUBTITLE FULL
OK
D0009-EN
2 Press the 6 buttons to choose a
ZOOM mode. Then press the a button
The picture expands and the chosen ZOOM mode is displayed in about 5 seconds.
• The ZOOM mode may be automatically changed by the control signal from an external device. When you want to return to the previous ZOOM mode, choose the ZOOM mode again.
Adjusting the visible area of the
picture
If subtitles or the top (or bottom) of the picture are cut off, you can adjust the visible area of the picture manually.
1 Press the c button
The ZOOM menu appears.
2 Press the a button to display the
ZOOM mode indicator
The indicator appears.
16 : 9 ZOOM
D0010-EN
3 While it is displayed, press the 6
buttons to change the position of the picture
• You cannot adjust the visible area in REGULAR or FULL mode.
20
LT-32/26D50BJ/SJ / LCT1703-001B-U / ENGLISH
LT-32&26D50BJSJ_Eng.book Page 21 Thursday, October 7, 2004 4:42 PM
• The visible area adjustment is saved even after the TV channel is changed. However, it is cancelled if the following operations are performed.
– The power is turned off/on – The ZOOM mode is changed – The X (Multi) button, f (Freeze)
button, or g (Text) button is pressed
– The TV is switched between TV mode
and EXT mode
• Some menu displays can be cut off when you move the visible area up or down while watching Digital terrestrial broadcasting (DVB-T).

3D SOUND function

You can enjoy sounds with a wider ambience.
• This function does not work for the sound from headphones.
Basic operations (Remote control)
Press the 3 button to select one of 3D SOUND modes
HIGH/LOW:
When you listen to stereo sound, please select HIGH or LOW mode. You can enjoy sound similar to the experience at the theatre. When you combine the functions of A.H.B. and BBE, you can enjoy more powerful sound.
• When you set the 3D SOUND function to HIGH mode, there may be slight volume distortion. If that occurs, please switch to LOW mode. The effect of 3D SOUND functions will be less noticeable, but the volume distortion will be corrected.
MONO:
Select the MONO mode, when you listen to the mono sound. You can enjoy the sound for a wider audience similar to stereo sound.
OFF:
The 3D SOUND function switches off.
• You can choose the 3D SOUND mode with the “SOUND menu” (see page 49).
21
LT-32/26D50BJ/SJ / LCT1703-001B-U / ENGLISH
LT-32&26D50BJSJ_Eng.book Page 22 Thursday, October 7, 2004 4:42 PM

Operation while watching DTV

Information function

When the h (Information) button is pressed, the programme information appears for approximately 1 minute.
D0203-EN
41
ITV News
Now: 13:00-14:00 Steve Scott
13:19
Next: 14:00-14:30 Steve Scott
CH61
•When the h (Information) button is pressed while the information is being displayed, the information disappears.
• The time display in the programme information uses the time information which is included in the Digital terrestrial broadcasting (DVB-T). Depending on the channel, the time information may not be correct.

Using the “Multi-picture” function

1 Press the X button
The “Multi-picture” menu appears.
1
D0101-EN
2 Press the 5 buttons and choose
2, then press the a button
1
D0102
2
D0103
22
212
Choose to return to one screen.
Choose to change to 2-pictures multi.
2-pictures multi:
Main-
picture
D0056
Sub­picture
With 1125i and 750p signals, the screen is split into two as shown below.
Main-
picture
(16:9)
12
D0104
D1056
This cannot be chosen when watching Digital terrestrial broadcasting (DVB-T).
Sub­picture
• You can watch Digital terrestrial broadcasting (DVB-T) in the main­picture. You can watch the Analogue terrestrial broadcasting or EXT picture in the sub-picture. When watching Digital terrestrial broadcasting (DVB-T) and Analogue terrestrial broadcasting at the same time, spilt the antenna and connect it to both the digital and analogue antenna terminals. (See page 9.)
• When the Digital terrestrial broadcasting (DVB-T) in the main­picture is 16:9 FULL, the main-picture aspect ratio is 16:9.
• When set to 2-pictures multi, the main­picture sound from the TV speaker can be changed to the sub-picture sound by pressing the c button. (The speaker mark moves from the main-picture to the sub-picture.) The sound changes to the main-picture sound if the c button is pressed again. When the headphones are connected, you can listen to the sound from the side at which the headphone mark is displayed. No sound comes from the TV speaker.
• Choose the main-picture channel by pressing the p p buttons. Choose the sub-picture channel by pressing the p buttons.
• The “Multi-picture” function does not work for a PC signal.
LT-32/26D50BJ/SJ / LCT1703-001B-U / ENGLISH
LT-32&26D50BJSJ_Eng.book Page 23 Thursday, October 7, 2004 4:42 PM
Operation while watching DTV
• 1125i, 625p, and 525p signal pictures cannot be displayed as the sub-picture.
• The BLUE BACK function does not work when the “Multi-picture” function is being used.
• The ZOOM function does not work when the “Multi-picture” function is being used.
To return the multi-picture to one screen:
Press the X button, press the 5 buttons to choose one screen, and then press the a button.
• Pressing the
TV/DTV button will also
return the display to one screen.

Using the Electronic Programme Guide (EPG)

The EPG screen appears when the GUIDE button is pressed while watching Digital terrestrial broadcasting (DVB-T).
1 BBC ONE
Channels Current Event Next Event
1. BBC ONE
2. BBC TWO
7. BBC THREE
30. CBBC Channel
40. BBC NEWS 24
D0204-EN
The Rugby Worid Cup...
OK
Select PR Watch PR
1 Quarter-screen
The programme you are watching is shown.
• Sometimes you may notice a drop in picture quality while watching your programme in the quarter-screen. This is not a fault.
2 Programme name, broadcast time
and brief description of programme
The programme name, broadcast time and a brief description of the programme are displayed for the programme chosen from the current event column or next event column.
3 Channel column 4 Current event column 5 Next event column
Electronic Programme Guide
13:12
The Rugby World Cu...
Fiji v USA, Italy v Tonga & Samoa v Uruguay
Movies Now
Next Event More..
07:45-15:10
23
LT-32/26D50BJ/SJ / LCT1703-001B-U / ENGLISH
LT-32&26D50BJSJ_Eng.book Page 24 Thursday, October 7, 2004 4:42 PM
Operation while watching DTV
Press the h (Information) button to display the help screen. Press it again to return to the EPG screen.
1 BBC ONE
MENU
OK
Select PR Watch PR
D0205-EN
Red: Page up Green: Page down TV/DTV: Go to DTV Guide: Leave guide Back: Go to previous
OK
Electronic Programme Guide
13:12
The Rugby World Cu... 07:45-15:10
Fiji v USA, Italy v Tonga & Samoa v Uruguay
Next Event More..
Help screen
i: Exit help
Choosing a channel
1 Press the 6 buttons and choose
a channel
The programme name, broadcast time and a brief description of the programme are displayed.
• Press the red and green buttons to scroll the channel column.
2 Press the a button
The chosen programme appears on the quarter-screen.
•When the GUIDE, TV/DTV, H or b buttons are pressed, the EPG screen disappears and the normal screen returns.
3 Press the a button
The scheduled icon appears at the right of the chosen programme and the scheduling is completed.
Scheduled icon
Channels Current Event Next Event
1. BBC ONE
2. BBC TWO
7. BBC THREE
30. CBBC Channel
40. BBC NEWS 24
D0206-EN
The Rugby Worid Cup... Movies Now
Select PR Set reminder On/OffOKCurrent Event More..
• Steps 1 to 3 can be repeated to schedule more programmes.
• When the
GUIDE, TV/DTV, H or
b buttons are pressed, the EPG
screen disappears and the normal screen returns.
When the TV is being watched, it automatically changes to the channel of the scheduled programme when the start time of the scheduled program is reached.
• The scheduling function does not work when the TV is turned off.
Cancelling a scheduled programme.
Display the EPG screen, choose a programme which has the scheduled icon ( ), and press the a button. The icon disappears and the scheduling is cancelled.
Checking programme details
Set reminder
When you schedule a programme, you will not miss a programme that you want to watch.
1 Press the 5 buttons and choose
the Next Event column
2 Press the 6 buttons and choose
the program that you want to schedule
The programme name, broadcast time and a brief description of the chosen programme are displayed.
• Press the red and green buttons to scroll the channel column.
24
Press the 7 buttons and choose a programme from the Current Event or Next Event columns
The programme name, broadcast time and a brief description of the chosen programme appear.
• Press the red and green buttons to scroll the channel column.
• When the GUIDE, TV/DTV, H or b buttons are pressed, the EPG screen disappears and the normal screen returns.
LT-32/26D50BJ/SJ / LCT1703-001B-U / ENGLISH
LT-32&26D50BJSJ_Eng.book Page 25 Thursday, October 7, 2004 4:42 PM

Displaying the Subtitles

With Digital terrestrial broadcasting (DVB­T), some programmes are broadcast with subtitles. Subtitles can be displayed when watching these programmes.
Press the SUBTITLE button when watching Digital terrestrial broadcasting (DVB-T)
“Subtitle ON” appears at the top-left of the screen and, when the programme has subtitles, the subtitles are displayed.
Subtitle ON
D0207-EN
•When the again, “Subtitle OFF” appears and the subtitles disappear.
SUBTITLE button is pressed
Operation while watching DTV
25
LT-32/26D50BJ/SJ / LCT1703-001B-U / ENGLISH
LT-32&26D50BJSJ_Eng.book Page 26 Thursday, October 7, 2004 4:42 PM

Digital Teletext function

1 Press the g button
VCR/TV/ DVD switch
Number
buttons
Colour
buttons
2 Operate it with the colour buttons,
7
buttons
The digital teletext information appears.
BBC ONE
Powers
For a full list of sections, press SELECT
Contact info CBeebies Home Music Taking Care NEWS SPORT WEATHER MAIN MENU
Press TEXT to exit
D0208-EN
B B C
7 buttons and a button
The operation method may differ depending on the contents of the digital teletext. Follow the instructions displayed on digital teletext screen.
• When “Press SELECT” or similar message appears on the screen, press the a button.
With Digital terrestrial broadcasting (DVB­T), in addition to pictures and sound, you can also watch digital teletext. Digital teletext is sometimes broadcast at the same time as normal broadcasting.
26
• When the g (Text) button is pressed, the
TV returns to television broadcasting.
• With Digital terrestrial broadcasting (DVB-T), in addition to digital teletext broadcasting at the same time as normal broadcasting, there are also channels with just digital teletext broadcasting.
• The aspect ratio when watching a channel with just digital teletext broadcasting is the same as the aspect ratio of the picture watched previously.
• When you press the g (Text) button while subtitles are on, the subtitles are turned off. When you press the g (Text) button again, the digital teletext screen is displayed.
LT-32/26D50BJ/SJ / LCT1703-001B-U / ENGLISH
DTV
DTV
LT-32&26D50BJSJ_Eng.book Page 27 Thursday, October 7, 2004 4:42 PM

Operation with the DTV menu

Buttons used to operate the menus
TV/DTV

Displaying the DTV menu

1 Press the H button to display
the menu bar
D0105-EN
• DTV in the menu bar can only be chosen when watching Digital terrestrial broadcasting (DVB-T).
2 Press the 5 buttons to choose
the DTV
D1105-EN
3 Press the a button
The DTV menu appears.
DTV
Timers
Configuration
Edit PR List
Installation
Common Interface
D0209-EN
4 Press the 6 buttons to choose
the item
• Press the b button to return to
the previous menu.
• Press the
TV/DTV or H button
to exit from the menu.
Chosen menu name

Timers (DTV Timer Recording)

By setting the timer, you can record a Digital terrestrial broadcasting (DVB-T) programme with a VCR connected to EXT-2 while you are out.
• Before using DTV timer recording, the VCR and TV must be connected up correctly. For details, see “Connection when recording to VCR” on page 65.
• When you have a T-V LINK compatible VCR connected to EXT-2, all you need to do is set the TV timer settings and the programme will be recorded. By using “Direct Rec” of the T-V LINK function, the Direct Rec commands are sent from the TV to the VCR to automatically start and end the recording. It is not necessary to set the timer on the VCR.
• When your VCR is not T-V LINK compatible, you also need to set the VCR timer settings to match the TV timer settings.
• The recording may not start and stop at exactly the right times for some programmes. It is recommended that you allow some leeway when setting the recording times.
• Provided that the days and times are not the same, you can set up to five timer settings.
• When subtitles are ON, the subtitles displayed with the broadcast will be recorded. When you do not want to record the subtitles, you need turn OFF the Subtitle setting beforehand (See “Displaying the Subtitles” on page 25.).
• During DTV timer recording, you are unable to view the SET UP menu or the DTV menu.
• For menu items other than DTV, see page 43.
27
LT-32/26D50BJ/SJ / LCT1703-001B-U / ENGLISH
LT-32&26D50BJSJ_Eng.book Page 28 Thursday, October 7, 2004 4:42 PM
Operation with the DTV menu
1 Choose Timers and press the a
button
The TIMER menu appears.
TIMER MENU 13:48 15/10/2003
No.
Name
1
BBC ONE
2
BBC ONE
3
BBC ONE
4
BBC ONE
5
BBC ONE
Change Mode Edit timer settings
D0210-EN
Start 00:00 00:00 00:00 00:00 00:00
OK
End 00:00 00:00 00:00 00:00 00:00
•When the h (Information) button is pressed, the help screen appears. When it is pressed again, the previous screen is returned to.
2 Press 6 buttons to choose the
timer number, and then press the a button
The timer setting window appears.
TIMER MENU 13:49
No. 1 2 3 4 5
Name Start End Date Mode
Select Programme
D0211-EN
Name BBC ONE BBC ONE BBC ONE BBC ONE BBC ONE
Start 00:00 00:00 00:00 00:00 00:00
BBC ONE
01/01/2004
OK
Confirm Timer
End 00:00 00:00 00:00 00:00 00:00
Once
3Use the 7 buttons, number
buttons and a button to set the timer
• When setting the start time and end time, input 1200 for 12:00 PM, 1500 for 3:00 PM and 0000 for 12:00 AM.
Name:
Use the 5 buttons to choose the channel for which the timer is to be set.
Press the 4 button.
Start:
Set the timer start time with the number buttons.
•When the 5 buttons are pressed, the input position moves.
Press the 4 button.
28
Date 01/01/2000 01/01/2000 01/01/2000 01/01/2000 01/01/2000
Date 01/01/2000 01/01/2000 01/01/2000 01/01/2000 01/01/2000
BACK
Cancel
Mode Inactive Inactive Inactive Inactive Inactive
More..
15/10/2003
Mode Inactive Inactive Inactive Inactive Inactive
More..
End:
Set the timer end time with the number buttons.
• When the 5 buttons are pressed, the
input position moves.
Press the 4 button.
Date:
Set the date for the timer to work with the number buttons.
• When the 5 buttons are pressed, the
input position moves.
Press the 4 button.
Mode:
Use the 5 buttons to choose the timer mode (Once/Daily/Weekly), and then press the a button.
4 Prepare your VCR for recording
When recording on a T-V LINK compatible VCR:
1. Insert the videotape for recording into the VCR and set the recording mode.
2. Make sure the VCR is ready to receive Direct Rec commands from the TV.
• Make sure other VCR timer settings
do not coincide with the TV timer settings.
• For details, see your VCR
instruction manual.
When recording on a T-V LINK incompatible VCR:
1. Insert the videotape for recording into the VCR and set the recording mode.
2. Set the VCR recording timer settings.
• Make the start and end time match
that of the TV timer.
• Set the VCR to record the signal
from the external input that the TV is connected to.
• For details, see your VCR
instruction manual.
When you have finished Step 4, you have set the timer.
When you are not watching TV, make sure the TV is in standby.
LT-32/26D50BJ/SJ / LCT1703-001B-U / ENGLISH
LT-32&26D50BJSJ_Eng.book Page 29 Thursday, October 7, 2004 4:42 PM
Operation with the DTV menu
The TV power lamp begins flashing at three minutes before the timer start time. If you are watching TV at the time, a message appears on the screen to inform you the timer is about to start. If the TV is in Standby, the power lamp lights orange while timer recording is in progress.
• When performing timer recording with a T-V LINK compatible recording device, test the timer recording before you record the programme. There are some T-V LINK compatible recording device that will not correctly receive the Direct Rec command from the TV. If the recording device does not operate when the recording start time is reached, it is not receiving the Direct Rec command from the TV. In this case, follow the instructions of “When recording on a T-V LINK incompatible VCR:”.
While the timer is in operation:
• You can turn the TV on or off (Standby). WARNING: Do not turn off the main power.
• You can watch Analogue terrestrial broadcasting channels or the pictures via an EXT terminal.
• Please note that any programme information that appears on the screen, such as when making changes to the Digital terrestrial broadcasting (DVB-T) channel picture, will be superimposed over the picture in the VCR recording.
• You cannot change Digital terrestrial broadcasting (DVB-T) channels while recording.
Cancelling and resetting the timer setting:
Cancelling the timer setting
Display the TIMER MENU and press the 6 buttons to choose which timer setting to cancel. Press the 5 buttons so that “Inactive” appears in the Mode column.
Reactivating the cancelled timer setting
Display the TIMER MENU and press the 6 buttons to choose which timer setting to reactivate. Press the 5 buttons so that “Active” appears in the Mode column.
Aborting timer recording
Display the Digital terrestrial broadcasting (DVB-T) channel picture on the screen and press the
(Information) button. A
h
window will appear asking if you want to stop the recording. Press the a button to abort the recording. If you want to continue recording, press the
TV/DTV
button.
• If, while attempting to perform timer recording to a T-V LINK compatible VCR, the TV timer operation starts but the VCR does not start recording, the problem is with the VCR. Resolve the VCR-related problem and see “Aborting timer recording” to abort the recording. After this is done, reset the timer.
• When you are watching TV at the recording start time, you may see an error message stating that recording could not start because of a VCR­related problem. See “Direct Rec” on page 13, which lists and explains each error message.
29
LT-32/26D50BJ/SJ / LCT1703-001B-U / ENGLISH
LT-32&26D50BJSJ_Eng.book Page 30 Thursday, October 7, 2004 4:42 PM
Operation with the DTV menu

Configuration

Set the basic setting for watching Digital terrestrial broadcasting (DVB-T).
Choose configuration and press the a button
CONFIGURATION appears.
CONFIGURATION
Change preferred audio language More..
D0212-EN
•When the b button is pressed, the
previous screen is returned to. When the
TV/DTV or H buttons are pressed,
the menu disappears.
•When the h (Information) button is
pressed, the help screen appears. When it is pressed again, the previous screen is returned to.
Audio Language
With Digital terrestrial broadcasting (DVB­T), a number of languages can be broadcast at the same time. Choose the language you want to listen to when watching these broadcasts.
1 Press the 6 buttons and choose
Audio Language
2 Press the 5 buttons and choose
the language
The language changes every time the button is pressed.
• If the selected language is not broadcast, the default language will be played.
Audio Language Subtitle Favourite Mode Receiver Upgrade Enter PIN code
English English
Off
V.3.3
Subtitle language
With Digital terrestrial broadcasting (DVB­T), a number of subtitles can be broadcast at the same time. Choose the subtitle you want to display when watching these broadcasts.
1 Press the 6 buttons and choose
Subtitle
2 Press the 5 buttons and choose
a subtitle language that appears when the SUBTITLE button is pressed
The subtitle language changes every time the button is pressed.
Favourite Mode
Enable/disable the Edit PR List Favourites settings.
1 Press the 6 buttons and choose
Favourite Mode
2 Press the 5 buttons and choose
ON or OFF
On:
The Edit PR List Favourites settings are enabled. When the p p button is pressed, only the channels chosen in the Edit PR List Favourites (those with the icon) can be chosen.
• For details on how to set your favourite channels, see “Setting the favourite channels” on page 34.
Off:
The Edit PR List Favourites settings are disabled When the p p button is pressed, all the channels registered in the Edit PR List can be chosen.
30
LT-32/26D50BJ/SJ / LCT1703-001B-U / ENGLISH
LT-32&26D50BJSJ_Eng.book Page 31 Thursday, October 7, 2004 4:42 PM
Operation with the DTV menu
Receiver Upgrade
Set the method to upgrade the Digital terrestrial broadcasting (DVB-T) receiver software.
1 Press the 6 buttons and choose
Receiver Upgrade, and press the a button
The setting window appears.
CONFIGURATION
Automatic Download Search for New Version
Switch automatic upgrade
D0213-EN
• The actual version may be different to the Receiver Upgrade version displayed above.
2 Press the 6 buttons and choose
Automatic Download, and press the 5 buttons to choose Enable or Disable
Enable (factory settings):
The Digital terrestrial broadcasting (DVB-T) software is automatically updated every day at 3:00 am. When enabled, the TV also searches for new software whenever it goes to standby.
Disable:
The Digital terrestrial broadcasting (DVB-T) software is not automatically updated.
Manually updating the Digital terrestrial broadcasting (DVB-T) information
Press the 6 buttons and choose Search for New Version, then press the a button
The Digital terrestrial broadcasting (DVB-T) information is updated.
Audio Language Subtitle Favourite Mode Receiver Upgrade Enter PIN code
Enabled
Exit submenu More..
BACK
English English
Off
V.3.3
In the future, there is a possibility that the Receiver Update function may also be able to be used to update the broadcasting (DVB-T)
Digital terrestrial
software and add new
functions.
Enter PIN code
Choose Enter PIN code to change the PIN code for the Edit PR List menu’s “Lock”. The PIN code factory setting (how it is set when you purchase the television) is 0000.
1 Press the 6 buttons and choose
Enter PIN code, then press a button
2 Input the current PIN code
When you are making this setting for the first time, input 0000. When a PIN code has already been set, enter the correct PIN code. The PIN code setting window appears.
CONFIGURATION
PIN code: Confirm:
..
90
Enter PIN code
D0225-EN
3 Press the number buttons to input
a new PIN code (password)
4 Input the new PIN code (password)
again in the Confirm box
Your newly chosen PIN code is now set. You will now need to use the PIN code (password) you chose here to lock or unlock the Edit PR List’s “Lock”.
Audio Language Subtitle Favourite Mode Receiver Upgrade Menu Lock Enter PIN code
Exit PIN code menu
BACK
English English
Off
V.3.5
Installation
More..
31
LT-32/26D50BJ/SJ / LCT1703-001B-U / ENGLISH
LT-32&26D50BJSJ_Eng.book Page 32 Thursday, October 7, 2004 4:42 PM
Operation with the DTV menu

Edit PR List

The Edit PR List can be used to do the following:
• delete registered channels
• edit channel names
• lock channels so that they cannot be watched by children
• set Favorites so that you can easily choose from only the channels you often watch.
Choose Edit PR List and press the a button
EDIT PR LIST appears.
• Sometimes you may notice a drop in picture quality while watching your programme in the quarter-screen. This is not a fault.
1 BBC ONE
Select Delete Edit Name Lock Favourites
Select function Watch PR
D0202-EN
•When the b button is pressed, the previous screen is returned to. When the
TV/DTV or H buttons are pressed,
the menu disappears.
•When the h (Information) button is pressed, the help screen appears. When it is pressed again, the previous screen is returned to.
1. BBC ONE
2. BBC TWO
7. BBC THREE
30. CBBC Channel
40. BBC NEWS 24
51. BBCi
Select PR
EDIT PR LIST
OK
More..
Choosing a channel
The chosen channel is shown on the quarter­screen.
1 Press the 5 buttons and choose
Select on the bar at the bottom of the screen
2 Press the 6 buttons and choose
a channel, and then press the a button
The picture of the chosen channel is shown on the quarter-screen.
Deleting a channel
1 Press the 5 buttons and choose
Delete on the bar at the bottom of the screen
2 Press the 6 buttons and choose
the channel to be deleted, and then press the a button
The channel deletion confirmation window appears.
2 BBC TWO
The selected service will be permanently deleted. Are you sure?
Yes
Select Delete Edit Name Lock Favourites
Select function Delete PR
D0215-EN
3 Choose Yes and press the a
button
The chosen channel is deleted.
• If you do not want to delete the chosen
channel, choose No and press the a button.
1. BBC ONE
2. BBC TWO
7. BBC THREE
30. CBBC Channel
40. BBC NEWS 24
51. BBCi
Select PR
EDIT PR LIST
No
OK
More..
32
• Perform “Installation” (see page 34) to re-register a channel that you have deleted.
LT-32/26D50BJ/SJ / LCT1703-001B-U / ENGLISH
LT-32&26D50BJSJ_Eng.book Page 33 Thursday, October 7, 2004 4:42 PM
Operation with the DTV menu
Editing a channel name
1 Press the 5 buttons and choose
Edit Name on the bar at the bottom of the screen
2 Press the 6 buttons and choose
the channel to be edited, and then press the a button
The edit window appears.
2 BBC TWO
BBC TWO
Select Delete Edit Name Lock Favourites
Select function Edit PR name
D0216-EN
EDIT PR LIST
1. BBC ONE
2. BBC TWO
7. BBC THREE
30. CBBC Channel
40. BBC NEWS 24
51. BBCi
OK
Select PR More..
3 Press the 6 buttons and choose
a character, press the 5 buttons to move the cursor and edit the name, and then press the a button
The edited channel appears in the Edit PR List.
• Delete any unnecessary characters by entering spaces over them.
Locking a channel
Digital terrestrial broadcasting (DVB-T) channels can be locked in the same way as the FEATURES menu CHILD LOCK.
1 Press the 5 buttons and choose
Lock on the bar at the bottom of the screen
2 Press the 6 buttons and choose
the channel to be locked, and then press the a button
The Enter PIN code input window appears.
2 BBC TWO
Enter PIN code
Select Delete Edit Name Lock Favourites
..
90
Enter PIN code
D0217-EN
EDIT PR LIST
1. BBC ONE
2. BBC TWO
7. BBC THREE
30. CBBC Channel
40. BBC NEWS 24
51. BBCil
More..
3 Press the number buttons to input
the correct PIN code and press the a button
If you have not changed the PIN code in the CONFIGURATION menu’s “Enter PIN code” (see page 31), input 0000. If you have changed the PIN code in the CONFIGURATION menu’s “Enter PIN code” (see page 31), input the PIN code you chose. The lock icon appears next to the channel name in the Edit PR List.
2 BBC TWO
Select Delete Edit Name Lock Favourites
..
90
Enter PIN code
D0218-EN
EDIT PR LIST
1. BBC ONE
2. BBC TWO
7. BBC THREE
30. CBBC Channel
40. BBC NEWS 24
51. BBCi
More..
When a locked channel is chosen, the Enter PIN code input window will appear. If the correct PIN code is input, the picture appears.
• When you forget the PIN code for the “Lock”, you can unlock locked channels by performing Automatic Search (see “Installation” on page 34).
33
LT-32/26D50BJ/SJ / LCT1703-001B-U / ENGLISH
LT-32&26D50BJSJ_Eng.book Page 34 Thursday, October 7, 2004 4:42 PM
Operation with the DTV menu
Setting the favourite channels
Channels that you often watch can be set as favourite channels. You can choose from just those channels when the p p buttons are pressed.
• After setting the favourite channels, check that “Favourite Mode” in “Configuration” (see page 30) is set to ON.
1 Press the 5 buttons and choose
Favourites on the bar at the bottom of the screen
2 Press the 6 buttons and choose
the channel to be registered as a favourite channel, and then press the a button
The favourite icon appears to the right of the chosen channel.
IST
D0219-EN

Installation

Use when re-registering a channel or when registering a new channel.
1 Choose Installation and press the
a button
The Installation menu appears.
Installation
Automatic Search
Manual Search
Factory Settings
D0220-EN
2 Press the 6 buttons and choose
the channel registration method, and then press the a button
Automatic Search:
Choose to automatically register the channels that can be received.
When Automatic Search is chosen and the a button is pressed, the confirmation window appears.
Start automatic search? Current PR list will be replaced.
Yes No
D0221-EN
To perform Automatic Search, choose Yes and press the a button. To cancel, choose No and press the a button.
Manual Search:
Choose to register a particular channel.
Installation > Manual Search
Channel Number
61
34
Signal Level:
Signal Quality:
OK
Start..
D0222-EN
Move cursor
90
Enter CH number
More..
Press the number buttons and input the channel that you want to register, and then press the a button. The Manual Search starts and the input channel is registered if it can be received.
LT-32/26D50BJ/SJ / LCT1703-001B-U / ENGLISH
LT-32&26D50BJSJ_Eng.book Page 35 Thursday, October 7, 2004 4:42 PM
Factory Settings:
Choose when you have moved house etc and want to automatically re-register all the channels. In addition to registering all the channels that can be received, it will reset the timer settings.
When Factory Settings is chosen and the a button is pressed, the confirmation window appears.
Are you sure you want to delete the PR list and reset all settings?
Yes No
D0223-EN
To perform Factory Settings, choose Yes and press the a button. To cancel, choose No and press the a button.

Common Interface

Choose when a pay television reception module is inserted into the Common Interface slot on the back of the TV, and you want to set the module.
When Common Interface is chosen and the a button is pressed, the name of the inserted module appears. When the a button is then pressed, the module setting menu appears.
• When no module is inserted, “No CI Module” appears.
• Refer to the module instruction manual for details of the settings.
Operation with the DTV menu
35
LT-32/26D50BJ/SJ / LCT1703-001B-U / ENGLISH
LT-32&26D50BJSJ_Eng.book Page 36 Thursday, October 7, 2004 4:42 PM

Operation while watching analogue TV

Information function

You can see the channel number of the programme you are watching, the current time or the PR LIST. From the PR LIST, you can choose a channel or EXT terminal.
Press the h (Information) button to display the information you want to
see.
Pressing the h (Information) button changes the display as follows:
PR LIST
PR ID
AV
BBC1
01 02 03 04 05 06 07 08 09
OK
+10-10
D0011-EN
Channel number display:
The channel number and channel name (when the channel name is registered) of the programme you are watching or the EXT terminal number is displayed.
Time display:
The current time of the teletext data is displayed. If the TV has not received a TV channel that has teletext programmes since it was turned on, the time display is blank. To view the current time, choose a TV channel that has teletext programmes.
• An incorrect current time is sometimes displayed when watching videos.
Channel number display
12 : 00
No indication
PR LIST:
The programme number (PR) and EXT terminal list is displayed. Pressing the a button after choosing the programme number (PR) or EXT terminal with the 7 buttons will display the chosen programme or EXT terminal.
• For programme numbers (PR) for which
the CHILD LOCK function is set, the n (CHILD LOCK) mark is displayed. For details see “CHILD LOCK” on page 50.
• For programme numbers (PR) which is
registered as a favourite channel, the d (favourite) mark is displayed. For details see “Favourite channel function” on page 38.
36
LT-32/26D50BJ/SJ / LCT1703-001B-U / ENGLISH
LT-32&26D50BJSJ_Eng.book Page 37 Thursday, October 7, 2004 4:42 PM
Operation while watching analogue TV

Using the “Freeze” function

You can view the current programme as a still picture.
1 Press the f button
The still picture of the current picture will appear.
current
programme
D0056
still picture
To cancel the “Freeze” function:
Press the f button, the p p buttons or the number buttons.
• The “Freeze” function does not work while a sub-picture is displayed.
• The still picture cannot be output from the TV.
• The “Freeze” function does not work for picture of PC signal.

Using the “Multi-picture” function

1 Press the X button
The “Multi-picture” menu appears.
1
D0101-EN
2 Press the 5 buttons to choose
the number of screens and then press the a button
1
D0102
212
Choose to return to one screen.
2-pictures multi:
Main-
picture
D0056
Sub­picture
With 1125i and 750p signals, the screen is split into two as shown below.
Main-
picture
D1056
Sub­picture
12-pictures multi:
Still pictures
Moving
D0058
picture
• When set to 2-pictures multi, you can view a TV picture and a picture from an external device. You cannot view a TV picture on more than one screen at the same time.
• When 12-pictures multi is set, pictures from external devices are not displayed.
• When set to 2-pictures multi, the main­picture can be changed by pressing the p p buttons. The sub-picture screen can be changed by pressing the p buttons. When set to 12-pictures multi and there are more than 12 pictures, the next or previous 12 screens can be displayed by pressing the p buttons.
D0103
D0104
Choose to change to 2-pictures multi.
2
Choose to change to 12-pictures multi.
12
Changing the sub-picture Displaying the next or previous 12 screens
37
LT-32/26D50BJ/SJ / LCT1703-001B-U / ENGLISH
LT-32&26D50BJSJ_Eng.book Page 38 Thursday, October 7, 2004 4:42 PM
Operation while watching analogue TV
• When set to 2-pictures multi, the main­picture sound from the TV speaker can be changed to the sub-picture sound by pressing the c button. (The speaker mark moves from the main-picture to the sub-picture.) The sound changes to the main-picture sound if the c button is pressed again. When the headphones are connected, you can listen to the sound from the side at which the headphone mark is displayed. No sound comes from the TV speaker.
• A picture of EXT-4 cannot be displayed as the sub-picture.
• The “Multi-picture” function does not work for a PC signal.
• You cannot view a scrambled channel in the sub-picture.
• When set to 12-pictures multi, press the 7 buttons to choose the screen you want to view and the press the a button to display that picture on the whole screen.
• The BLUE BACK function does not work when the “Multi-picture” function is being used.
• The ZOOM function does not work when the “Multi-picture” function is being used.
To return the “Multi-picture” to one screen:
Press the X button, press the 5 buttons to choose one screen, and then press the a button.
• Pressing the return the display to one screen.
TV/DTV button will also

Favourite channel function

You can register your favourite TV channels (PR 1 – PR 99) in the number buttons 1 to 4. After registering, the channel can be called by pressing the d (favourite) button and a number button 1 to 4.
Favourite channel registration
1 In the normal screen, choose a TV
channel (PR 1 – PR 99) that you want to register
For details, refer to “Choose a TV channel and watch images from external devices” on page 18.
2 Press and hold the d (favourite)
button for three seconds or more
Then “SET 1-4?” appears on the screen.
3 Press one of the number buttons 1
to 4
The current channel is registered in the pressed number button. After “PROGRAMMED!” appears on the screen, the favourite channel icon appears at the top-right of the screen.
• If the channel you are trying to register is already registered in one of the other number buttons 1 to 4, “NOT AVAILABLE” appears on the screen.
• Channels locked with the CHILD LOCK function cannot be registered.
• If AUTO PROGRAM is performed, the registered favourite channels are reset.
• When you want to delete a favourite channel, delete the set channel and set contents with FAVOURITE SETTING (see page 52) in the FEATURES menu.
38
LT-32/26D50BJ/SJ / LCT1703-001B-U / ENGLISH
LT-32&26D50BJSJ_Eng.book Page 39 Thursday, October 7, 2004 4:42 PM
Calling the favourite channel
1 In the normal screen, press the d
(favourite) button
Then “FAVOURITE1-4?” appears.
2 Press one of the number buttons 1
to 4
The called favourite channel appears on the screen.
• If a number button in which no channel is registered is pressed, “NO MEMORY” appears on the screen.
Setting the picture effect
When a favourite channel has been chosen with the d (favourite) button and number buttons 1 to 4, picture effect settings can be memorised for each favourite channel by setting the picture effects in the PICTURE menu (see page 45). The following items in the PICTURE menu (see page 45) are memorised. PICTURE MODE BRIGHT-1 CONTRAST BRIGHT-2 SHARP COLOUR HUE COLOUR TEMP. DIGITAL VNR COLOUR SYSTEM The last setting made for each item is memorised.
Operation while watching analogue TV
39
LT-32/26D50BJ/SJ / LCT1703-001B-U / ENGLISH
LT-32&26D50BJSJ_Eng.book Page 40 Thursday, October 7, 2004 4:42 PM

Analogue teletext function

Basic operation

1 Choose a TV channel with a teletext
VCR/TV/
Number
buttons
Colour
buttons
7
buttons
DVD switch
2 Set the VCR/TV/DVD switch to the
3 Press g (Text) button to display
broadcast
TV position
the teletext
Pressing g (Text) button changes the mode as follows:
TEXT
---
TEXT
---
D1043-EN
TV mode
TEXT TEXT
---
---
TV and text mode
Text mode
4 Choose a teletext page by pressing
the p p buttons, number buttons or colour buttons
To return to the TV mode:
Press the
TV/DTV button or g (Text)
button.
• If you have trouble receiving teletext broadcasts, consult your local dealer or the teletext station.
• The ZOOM function will not work in the TV and text mode or Text mode.
• You cannot operate menus when viewing a teletext programme.
40
LT-32/26D50BJ/SJ / LCT1703-001B-U / ENGLISH
LT-32&26D50BJSJ_Eng.book Page 41 Thursday, October 7, 2004 4:42 PM
Analogue teletext function

Using the List Mode

You can store the numbers of your favourite teletext pages in memory and call them up quickly using the colour buttons.
To store the page numbers:
1 Press B button to go into the
List mode
The page numbers you have stored are displayed at the bottom of the screen.
2 Press a colour button to choose a
position. Then press the number buttons to enter the page number
3 Press and hold down the A (Store)
button
The four page numbers blink white to show that they are stored in memory.
To call up a stored page:
1 Press the B button to enter the
List mode
2 Press a colour button having a
stored page

Hold

You can hold a teletext page on the screen for as long as you want, even while several other teletext pages are being received.
Press the C (Hold) button
Hold indication
To cancel the Hold function:
Press C (Hold) button again.

Sub-page

Some teletext pages include sub-pages that are automatically displayed.
1 Choose a teletext page that
includes sub-pages
Sub-page numbers that can be viewed are automatically displayed at the top of the screen.
2 Press the 5 buttons to choose a
sub-page number

Reveal

Some teletext pages include hidden text (such as answers to a quiz). You can display the hidden text.
Each time you press the E (Reveal) button, text is hidden or revealed
To exit the List mode:
Press the B button again.
41
LT-32/26D50BJ/SJ / LCT1703-001B-U / ENGLISH
LT-32&26D50BJSJ_Eng.book Page 42 Thursday, October 7, 2004 4:42 PM
Analogue teletext function

Size

You can double the height of the teletext display.
Press the F (Size) button

Index

You can return to the index page instantly.
Press the G (Index) button
Returns to page 100 or a previously specified page.

Cancel

You can search for a teletext page while watching TV.
1 Press the number button to enter a
page number, or press a colour button
The TV searches for a teletext page.
2 Press H (Cancel) button
The TV programme appears. When the TV finds the teletext page, its page number appears in the upper left of the screen.
3 Press H (Cancel) button to return
to a teletext page when the page number is on the screen
• The TV mode cannot be resumed by
pressing the H (Cancel) button. To return to the TV mode press b.
42
LT-32/26D50BJ/SJ / LCT1703-001B-U / ENGLISH
PICTURE
PICTURE
LT-32&26D50BJSJ_Eng.book Page 43 Thursday, October 7, 2004 4:42 PM

Setting the TV

Call the menu and perform the settings for the picture and sound.
Buttons used to operate the menus
TV/DTV

Basic operation

1 Press the H button to display
the menu bar
D2105-EN
2 Press the 5 buttons to choose
the menu you want to use and then press the a button
D3105-EN
Chosen menu
3 Press the 6 buttons to choose
the item to be set, press the 5 buttons to set the item, and then press the a button
If there are sub-menus, use the 7 buttons to operate them.
• Press the b button to return to
the previous menu.
• Press the TV/DTV or H button
to exit from the menu.
• Some menu items may not be operated or set depending on the TV status or other menu item settings. Menu items that cannot be operated or set are displayed in grey in the menu and cannot be chosen.
Chosen menu name
Types of menu
PICTURE menu
D0106
(see page 45)
SOUND menu
D0107
(see page 49)
FEATURES menu
D0108
(see page 50)
SET UP menu
D0109
(see page 53)
DTV menu
D0224
(see page 27)
• The menu will disappear after about one minute if no operation is performed.
The menu guide area can be made to appear and disappear for some menus. While the menu is displayed, press the h button to change between the guide area being displayed and not displayed.
>> 4:3 AUTO ASPECT
PANORAMIC REGULAR 14:9 ZOOM
OK
D0017-EN
Guide area
>> 4:3 AUTO ASPECT
PANORAMIC REGULAR 14:9 ZOOM
D1017-EN
• The guide area for some menus will still
be displayed even if the h button is pressed. This is not a fault.
43
LT-32/26D50BJ/SJ / LCT1703-001B-U / ENGLISH
LT-32&26D50BJSJ_Eng.book Page 44 Thursday, October 7, 2004 4:42 PM
Setting the TV
Operation with the buttons on the TV
You can also operate the menus using the buttons on the front panel of the TV.
TV/AV button
MENU/OK button
6 buttons
5 buttons
44
LT-32/26D50BJ/SJ / LCT1703-001B-U / ENGLISH
LT-32&26D50BJSJ_Eng.book Page 45 Thursday, October 7, 2004 4:42 PM

PICTURE menu

PICTURE
PICTURE
STANDARD
PICTURE MODE BRIGHT-1 CONTRAST BRIGHT-2 SHARP COLOUR HUE COLOUR TEMP. FEATURES
D0014
-EN
OK
STANDARD
COOL
COOL
RESET
• While the PICTURE menu is displayed, pressing the blue button will set the BRIGHT-1, CONTRAST, BRIGHT-2, SHARP, COLOUR, HUE settings to their default settings.
• When watching the picture from EXT-1 to EXT-4 or the PC, picture effect settings can be memorised for each external input by setting the picture effects in the PICTURE menu. The following items in the PICTURE menu are memorised. PICTURE MODE BRIGHT-1 CONTRAST BRIGHT-2 SHARP COLOUR HUE COLOUR TEMP. DIGITAL VNR COLOUR SYSTEM The last setting made for each item is memorised.

PICTURE MODE

You can choose one of three PICTURE MODEs to adjust the picture settings automatically.
BRIGHT:
Heightens contrast and sharpness.
STANDARD:
Standardises picture adjustment.
SOFT:
Softens contrast and sharpness.

BRIGHT-1

You can adjust the back light.
2 : darker 3 : brighter

CONTRAST

You can adjust the picture contrast.
2 :lower 3 : higher

BRIGHT-2

You can adjust the picture brightness.
2 : darker 3 : brighter

SHARP

You can adjust the picture sharpness.
2 : softer 3 :sharper

COLOUR

You can adjust the picture colour.
2 : lighter 3 :deeper
HUE
You can adjust the picture tint.
2 : reddish 3 :greenish
• You can change the HUE setting (picture

COLOUR TEMP.

You can select one of three COLOUR TEMP. modes (three tones of white) to adjust the white balance of the picture. Since white is the colour which is used as a reference for all the other colours, changing the COLOUR TEMP. mode affects the appearance of all the other colours on the screen.
hue) when the colour system is NTSC
3.58, or NTSC 4.43.
45
LT-32/26D50BJ/SJ / LCT1703-001B-U / ENGLISH
LT-32&26D50BJSJ_Eng.book Page 46 Thursday, October 7, 2004 4:42 PM
PICTURE menu
COOL:
A bluish white. Using this mode when watching bright pictures allows you to enjoy a more vivid and bright picture.
NORMAL:
The normal white colour.
WARM:
A reddish white. Using this mode when watching films allows you to enjoy colours that are characteristic of films.

FEATURES

Choose FEATURES and press the a or 3 button to display the sub-menu.
> FEATURES
DIGITAL VNR Super DigiPure MOVIE THEATRE COLOUR MANAGEMENT PICTURE MANAGEMENT COLOUR SYSTEM 4:3 AUTO ASPECT
OK
D1015-EN
DIGITAL VNR
The DIGITAL VNR function cuts down the amount of ‘noise’ (‘snow’ or interference) in the original picture. You can choose from the three DIGITAL VNR function settings of AUTO, MIN and MAX.
AUTO(LOW)/AUTO(HIGH):
The TV will automatically adjust the level of the DIGITAL VNR effect to match the amount of noise in the picture, giving you the best possible picture.
• If you set the DIGITAL VNR effect too high it can make the picture less sharp. It is recommended you use the AUTO(LOW) setting if you can. If you set the DIGITAL VNR function to AUTO(LOW) but still notice some noise, change the setting from AUTO(LOW) to AUTO(HIGH).
46
AUTO(LOW)
AUTO AUTO
ON ON
MIN:
The level of the DIGITAL VNR effect is set to the minimum. If you set the DIGITAL VNR function to AUTO(LOW) but feel that the sharpness of the original picture has not been reproduced fully, change the setting from AUTO(LOW) to MIN.
• The MIN setting is not suitable for low­quality pictures which contain a lot of noise.
MAX:
The level of the DIGITAL VNR effect is set to the maximum. If you set the DIGITAL VNR function to AUTO(HIGH) but still notice some noise, change the setting from AUTO(HIGH) to MAX.
• The MAX setting is not suitable for high­quality pictures which contain very little noise.
Super DigiPure
The Super DigiPure function uses the latest in digital technology to give you a natural­looking picture. The Super DigiPure function includes the following two functions.
DigiPure function:
This function helps to create a natural­looking picture by eliminating unnecessary edges from high-contrast and crisp images. For images with low-contrast, edges are added to produce a sharper, more detailed picture. You can choose from the three DigiPure function settings of AUTO, MIN and MAX.
• If you set the DigiPure effect too high on a low-quality picture that contains a lot of noise, this may actually make the noise worse. We recommend you use the AUTO setting if you can.
Picture motion compensation function:
This function displays fast-moving pictures (for example, the players or ball in a football game) more smoothly and naturally on the screen.
• The effect level of the picture motion compensation function cannot be changed. The effect level is the same no matter which of the AUTO, MIN or MAX settings is used.
LT-32/26D50BJ/SJ / LCT1703-001B-U / ENGLISH
LT-32&26D50BJSJ_Eng.book Page 47 Thursday, October 7, 2004 4:42 PM
PICTURE menu
AUTO:
The TV will automatically adjust the level of the DigiPure effect to match the amount of noise in the picture, giving the best possible picture.
MIN:
The level of DigiPure effect is set to the minimum. When you set the Super DigiPure function to AUTO and notice some noise, change the setting from AUTO to MIN.
• The MIN setting is not suitable for high­quality pictures which contain very little noise.
MAX:
The level of DigiPure effect is set to the maximum. If you set the Super DigiPure function to AUTO but feel that the original picture quality has not been reproduced fully, change the setting from AUTO to MAX.
• The MAX setting is not suitable for low­quality pictures which contain a lot of noise.
OFF:
The Super DigiPure function is turned off.
MOVIE THEATRE
The MOVIE THEATRE function displays a cinema film picture more smoothly and naturally on the screen.
AUTO:
The television automatically recognizes the type of signal and turns the function on and off.
ON:
This function is turned on.
OFF:
This function is turned off.
COLOUR MANAGEMENT
This TV supports the COLOUR MANAGEMENT function to ensure dull colours are compensated to produce natural hues. The COLOUR MANAGEMENT function is on by default.
ON:
COLOUR MANAGEMENT function is turned on.
OFF:
COLOUR MANAGEMENT function is turned off.
• Set this function to ON under normal conditions.
PICTURE MANAGEMENT
The PICTURE MANAGEMENT function makes it easier to see the dark areas when a picture has many dark areas, and makes it easier to see the bright areas when a picture has many bright areas. Normally use with this function on.
ON:
PICTURE MANAGEMENT function is turned on.
OFF:
PICTURE MANAGEMENT function is turned off.
47
LT-32/26D50BJ/SJ / LCT1703-001B-U / ENGLISH
LT-32&26D50BJSJ_Eng.book Page 48 Thursday, October 7, 2004 4:42 PM
PICTURE menu
COLOUR SYSTEM
The colour system is chosen automatically. However, if the picture is not clear or no colour appears, choose the colour system manually.
1 Choose COLOUR SYSTEM. Then
press the a or 3 button
The sub-menu of the COLOUR SYSTEM function appears.
>> COLOUR SYSTEM
MAIN
PAL
OK
D0016-EN
2 Press the 5 buttons to choose
MAIN or SUB MAIN:
You can change the colour system of the main-picture.
SUB:
You can change the colour system of the sub-picture.
• Choose MAIN when a sub-picture is not displayed.
3 Press the 6 buttons to choose
the appropriate colour system. Then press the a button
PAL:
PAL system
SECAM:
SECAM system
NTSC 3.58:
NTSC 3.58 MHz system
NTSC 4.43:
NTSC 4.43 MHz system
AUTO:
This function detects a colour system from the input signal. You can only use this when you are viewing a picture from programme number PR 0 (AV), or an EXT terminal.
SUB
AUTO
• The AUTO function may not function properly if you have poor signal quality. If the picture is abnormal in the AUTO function, choose another colour system manually.
• When in the Programme numbers PR 0 (AV) to PR 99, you cannot choose NTSC
3.58 or NTSC 4.43. SECAM cannot be chosen when the COUNTRY setting is UNITED KINGDOM.
• COLOUR SYSTEM cannot be chosen when you are watching the Digital terrestrial broadcasting (DVB-T), the EXT-4 picture or PC picture.
4:3 AUTO ASPECT
You can choose one of three ZOOM modes, REGULAR, PANORAMIC or 14:9 ZOOM, as the ZOOM mode for the normal picture (4:3 aspect ratio).
1 Choose 4:3 AUTO ASPECT then
press the a button
>> 4:3 AUTO ASPECT
PANORAMIC REGULAR 14:9 ZOOM
OK
D0017-EN
2 Press the 6 buttons to choose a
ZOOM mode
48
LT-32/26D50BJ/SJ / LCT1703-001B-U / ENGLISH
LT-32&26D50BJSJ_Eng.book Page 49 Thursday, October 7, 2004 4:42 PM

SOUND menu

SOUND
STEREO/ BASS TREBLE BALANCE
D0019
3D SOUND A.H.B. BBE
OK
-EN
OFF OFF OFF
• When the headphones are connected, only “STEREO / I • II” can be used.
• STEREO / I • II cannot be chosen when watching Digital terrestrial broadcasting (DVB-T).

STEREO / I • II

When you are viewing a bilingual broadcast programme, you can choose the sound from Bilingual I (Sub I) or Bilingual II (Sub II). If you have poor reception on a stereo broadcast, you can change from stereo to mono sound so that you can hear the broadcast more clearly and easily.
s: Stereo sound
v : mono sound
t : Bilingual I (sub I)
u : Bilingual II (sub II)
• The sound mode you can choose differs depending on the TV programme.
• This function does not work in the EXT modes.

BASS

You can adjust the low tone of the sound.
2 : weaker 3 :strong

TREBLE

You can adjust the high tone of the sound.
2 : weaker 3 :strong

BALANCE

You can adjust the volume balance between the left and right speaker.
2 : turn the left speaker’s volume level up. 3 : turn the right speaker’s volume level up.

3D SOUND

You can enjoy Surround sound with a “live” effect by using the 3D SOUND function.
• You can choose a 3D SOUND mode from HIGH, LOW, MONO and OFF modes. For details, see “3D SOUND function” on page 21.
• You can also operate the 3D SOUND function with the 3 button. For details, see “3D SOUND function” on page 21.

A.H.B. (Active Hyper Bass)

Used when you want to emphasise the bass sound.
ON:
This function is turned on.
OFF:
This function is turned off.
BBE
BBE function restores clarity and presence for better speech intelligibility and musical realism.
ON:
This function is turned on.
OFF:
This function is turned off.
• Manufactured under license from BBE Sound, Inc. Licensed by BBE Sound, Inc. under USP4638258, 5510752 and
5736897. BBE and BBE symbol are registered trademarks of BBE Sound, Inc.
49
LT-32/26D50BJ/SJ / LCT1703-001B-U / ENGLISH
LT-32&26D50BJSJ_Eng.book Page 50 Thursday, October 7, 2004 4:42 PM

FEATURES menu

FEATURES
SLEEP TIMER CHILD LOCK APPEARANCE BLUE BACK FAVOURITE SETTING
OK
D0023-EN
TYPE A
ON
• CHILD LOCK, APPEARANCE, BLUE BACK, and FAVOURITE SETTING cannot be chosen when watching Digital terrestrial broadcasting (DVB-T).

SLEEP TIMER

You can set the TV to automatically turn off after a set period of time.
1 Choose SLEEP TIMER. Then press
the a or 3 button
A Sub-menu of the SLEEP TIMER function appears.
> SLEEP TIMER
0120
OFF
OK
D0024-EN
To cancel the SLEEP TIMER function:
Press the 2 button to set the period of time to “OFF”.

CHILD LOCK

When there is a TV channel you do not want your children to watch, you can use the CHILD LOCK function to lock out the TV channel. Even when a child chooses a programme number (PR) for a locked TV channel the screen will change to blue and display n (CHILD LOCK) so the TV channel cannot be viewed. Unless you enter a pre-set ID number by a special operation, the lock cannot be released and the child cannot view the TV channel.
To set the CHILD LOCK function
1 Choose CHILD LOCK, then press
the 0 button
“SET ID NO.” (ID number setting screen) appears.
> SET ID NO.
040
0
OK
D0025-EN
2 Press the 5 buttons to set the
period of time. Then press the a button
You can set the period of time for up to 120 minutes (2 hours) in 10 minute steps.
• One minute before the SLEEP TIMER function turns off the TV, “GOOD NIGHT!” appears.
• The SLEEP TIMER function cannot be used to turn off the TV’s main power.
• When the SLEEP TIMER function is on, you can display the sub-menu of the SLEEP TIMER function again to confirm or change the remaining period of time of the SLEEP TIMER function. Press the a button to leave the menu after confirming or changing the remaining time.
50
2 Set the ID number to your liking
1 Press the 6 buttons to choose
a number.
2 Press the 5 buttons to move
the cursor.
3 Press the a button
The Sub-menu of CHILD LOCK appears.
>> CHILD LOCK
BBC1 BBC2 ITV CH4 CH5
CH
CH 21 CH 22 CH 23 CH 24 CH 25 CH 26 CH 27 CH 28 CH 29
LOCK
D0026-EK
PR ID AV 01 02 03 04 05 06 07 08 09
OK
LT-32/26D50BJ/SJ / LCT1703-001B-U / ENGLISH
LT-32&26D50BJSJ_Eng.book Page 51 Thursday, October 7, 2004 4:42 PM
FEATURES menu
4 Press the 6 buttons to choose a
TV channel
Every time you press the 6 buttons, the Programme number (PR) changes, and the picture of the TV channel registered in the Programme number (PR) is displayed on the screen.
5 Press the blue button and set the
CHILD LOCK function. Then press the a button
n (CHILD LOCK) appears and the TV channel is locked.
To reset the CHILD LOCK function:
Press the blue button again. n (CHILD LOCK) disappears.
To disable easy resetting of the CHILD LOCK function, the menu disappears if you choose the CHILD LOCK function and press the a button.
To view a locked TV channel
1 Choose a programme number (PR)
of a locked TV channel with the number buttons or PR LIST
The screen changes to blue and the n (CHILD LOCK) appears. You cannot view the TV channel.
5
D0027-EN
If you have forgotten the ID number:
Perform step 1 of “To set the CHILD LOCK function”. After confirming the ID number, press the
TV/DTV button to exit
the menu.
• Even if you reset the lock temporarily, it does not mean that the CHILD LOCK function set for the TV channel is cancelled. The next time anyone tries to view the TV channel, it will be locked again.
• When you want to cancel the CHILD LOCK function, you must perform the operation “To set the CHILD LOCK function” again.
• To stop it being easy to choose the programme number (PR) of a locked TV channel, the programme number (PR) has been set so that it cannot be chosen with the 6 buttons or the buttons of the TV.
• To stop it being easy to reset the lock, “ID NO.” (ID No. input screen) is set so that it cannot appear unless you press the h (Information) button.

APPEARANCE

Press the 5 button and choose the format in which the channel number is displayed from the four types: TYPE A, TYPE B, TYPE C, and TYPE D.
2 Press the h (Information) button to
display “ID NO.” (ID No. input screen)
5
ID NO. :
D0028-EN
3 Press the number buttons to enter
the ID number
The lock is temporarily released so you can view the TV channel.
• Set to TYPE D when shipped from factory. TYPE D sets all screens to semitransparent. The menu screens are not semitransparent when set to a type other than TYPE D.
• The DTV menu is always semitransparent.
51
LT-32/26D50BJ/SJ / LCT1703-001B-U / ENGLISH
LT-32&26D50BJSJ_Eng.book Page 52 Thursday, October 7, 2004 4:42 PM
FEATURES menu

BLUE BACK

You can set the TV to automatically change to a blue screen and mute the sound if the signal is weak or absent, or when there is no input from an external device.
ON:
This function is turned on.
OFF:
This function is turned off.

FAVOURITE SETTING

Choose when deleting the analogue favorite channels registered in buttons 1 to 4.
1 Choose FAVOURITE SETTING,
then press the a or 3 button
The FAVOURITE SETTING menu appears.
FAVOURITE SETTING
1
2
3
4
OK
D0112-EN
PR
PR 01
PR 01
PR
2 Press the 6 buttons and chose
the favourite channel that you want to delete
3 Press the blue button
The chosen favourite channel and set contents are deleted.
• For details of the favourite channels, see “Favourite channel function” on page 38.
52
07
01
RESET
LT-32/26D50BJ/SJ / LCT1703-001B-U / ENGLISH
LT-32&26D50BJSJ_Eng.book Page 53 Thursday, October 7, 2004 4:42 PM

SET UP menu

SET UP
AUTO PROGRAM EDIT/MANUAL DECODER(EXT-2) COMPONENT AUTO SELECT EXT SETTING
OK
D0029
-EN
OFF OFF
• AUTO PROGRAM, EDIT/MANUAL, and DECODER (EXT-2) cannot be chosen when watching Digital terrestrial broadcasting (DVB-T).

AUTO PROGRAM (Analogue)

You can again perform the AUTO PROGRAM function TV channel automatic registration which was performed in the “Initial settings” (page 10).
1 Choose AUTO PROGRAM, then
press the a or 3 button
The COUNTRY menu appears.
2 Perform any extra operations you
need to perform in step 5 (operations after AUTO PROGRAM ends) and step 6 of “Initial settings”

EDIT/MANUAL (Analogue)

The EDIT/MANUAL functions are divided into two types:
• editing the current programme numbers (PR) (EDIT functions); and
• manually storing a TV channel you want to view on a particular programme number (PR) (MANUAL function).
Here are the details about these functions:
MOVE:
This function changes the programme number (PR) of a TV channel.
ID:
This function registers a channel name (ID) to a TV channel.
INSERT:
This function adds a new TV channel in the current programme numbers (PR) list by using the CH number.
• You cannot use the INSERT function if you do not know the channel number of a TV channel. Use the MANUAL function to register a TV channel in the programme number (PR).
DELETE:
This function deletes a TV channel you do not want to list.
MANUAL:
This function manually stores a new TV channel in a programme number (PR).
Caution
• Using the MOVE, DELETE or INSERT functions rewrites the current programme numbers (PR) list. Therefore, the programme numbers (PR) of some of the TV channels will change.
• Using the MANUAL function for a TV channel for which the CHILD LOCK function has been set cancels the CHILD LOCK function for that channel.
• Using the MANUAL function for a TV channel for which the DECODER (EXT-2) function has been set to ON returns the setting of the DECODER (EXT-2) function for that channel to OFF.
• When a TV channel has already been registered in PR 99, using the INSERT function deletes that TV channel.
53
LT-32/26D50BJ/SJ / LCT1703-001B-U / ENGLISH
LT-32&26D50BJSJ_Eng.book Page 54 Thursday, October 7, 2004 4:42 PM
SET UP menu
Basic operation
1 Choose EDIT/MANUAL, then press
the a or 3 button
The EDIT menu appears.
> EDIT
PR ID AV 01 02 03 04 05 06 07 08 09
OK
MOVE
D0038-EK
2 Follow the description for the
function you want to use
3 Press the a button to complete
the settings
The T-V LINK menu appears.
T-V LINK
DOWNLOAD TV RECORDING DEVICE
OK
D0005-EN
EXIT
• If you are not connecting the aerial cable to analogue aerial socket, or do not have a T-V LINK compatible VCR connected:
Press the
TV/DTV button to exit the T-V
LINK menu. The T-V LINK menu disappears.
If you have a T-V LINK compatible VCR connected to the EXT-2 terminal:
Follow “Downloading the data to VCR” on page 12 to transmit the programme number (PR) data.
• For programme number PR 0, “AV” appears in the programme numbers (PR) list.
• An EXT terminal number does not appear in the programme numbers (PR) list.
BBC1 BBC2 ITV CH4 CH5
CH
CH 21 CH 22 CH 23 CH 24 CH 25 CH 26 CH 27 CH 28 CH 29
INSERT
ID
MANUAL
DELETE
MOVE
1 Press the 6 buttons to choose a
TV channel
2 Press the 3 button to start the
MOVE function
> EDIT
PR ID AV 01 02 03 04 05 06 07 08 09
D0030-EK
CH
ID
BBC2
CH 22
ITV
CH 23
CH4
CH 24
CH5
CH 25 CH 26 CH 27 CH 28 CH 29
OK
STORE
CHBBC1
3 Press the 6 buttons to choose a
new programme number (PR)
To cancel the MOVE function:
Press the b button.
4 Press the 2 button to change the
programme number (PR) of a TV channel to a new programme number (PR)
DELETE
1 Press the 6 buttons to choose a
TV channel
2 Press the yellow button to delete
the TV channel
The TV channel is deleted from the programme numbers (PR) list.
21
54
LT-32/26D50BJ/SJ / LCT1703-001B-U / ENGLISH
LT-32&26D50BJSJ_Eng.book Page 55 Thursday, October 7, 2004 4:42 PM
SET UP menu
ID
1 Press the 6 buttons to choose a
TV channel
2 Press the red button to start the ID
function
> EDIT
BBC1 BBC2 ITV CH4 CH5
BBC1 BBC2 ITV CH4 CH5
M
CH
CH 21 CH 22 CH 23 CH 24 CH 25 CH 26 CH 27 CH 28 CH 29
CH
CH 21 CH 22 CH 23 CH 24 CH 25 CH 26 CH 27 CH 28 CH 29
ID LIST
ID LIST
PR ID AV 01 02 03 04 05 06 07 08 09
OK
D0031-EK
3 Press the 6 buttons to choose
the first character of a channel name (ID) you want to give the TV channel
> EDIT
PR ID AV 01 02 03 04 05 06 07 08 09
OK
D0032-EK
5 Press the 6 buttons to choose
the channel name (ID)
To cancel the ID function:
Press the b button.
6 Press the a button to give a
channel name (ID) to a TV channel
• You can give your own unique channel name (ID) to the TV channel. When you have finished step 3, do not go to step 4. Press the 5 buttons to move the cursor, and press the 6 buttons to choose each character of the channel name (ID). Then press the a button to register the channel name (ID) to the TV channel.
Before performing INSERT or MANUAL operation
• A CH/CC number unique to this TV and corresponding to the Channel number of a TV channel is required. Find the corresponding CH/CC number from a table “CH/CC NUMBER” on page 57 based on the Channel number of the TV channel.
4 Press the blue button to display the
ID LIST (channel name list)
> EDIT
PR ID
AV 01 02 03 04 05 06 07 08 09
D0033-EK
CH
BBC1
CH 21
BBC2
CH 22
ITV
CH 23
CH4
CH 24
CH5
CH 25 CH 26
M
OK
CH 27 CH 28 CH 29
ID LIST M6 MBC MCM MDR MOVIE MTV MTV3
55
LT-32/26D50BJ/SJ / LCT1703-001B-U / ENGLISH
LT-32&26D50BJSJ_Eng.book Page 56 Thursday, October 7, 2004 4:42 PM
SET UP menu
INSERT
1 Press the 6 buttons to choose a
programme number (PR) for which you will register a new TV channel
2 Press the green button and start
the INSERT function
> EDIT
BBC1 BBC2 ITV CH4 CH5
0 9
CH
CH 21 CH 22 CH 23 CH 24 CH 25 CH 26 CH 27 CH 28 CH 29
D0034-EN
PR ID AV 01 02 03 04 05 06 07 08 09
OK
To cancel the INSERT function:
Press the b button.
3 When the COUNTRY setting is
UNITED KINGDOM: Press the number buttons to enter the remaining CH number
• You cannot enter CC numbers.
When the COUNTRY setting is IRELAND: Press the 6 buttons to choose “CH” or “CC”, then enter the remaining CH or CC number
The TV shifts to registration mode. When the registration is completed, the picture of the TV channel appears on the screen.
• The CH/CC number is a number given to each broadcast frequency that carries a TV channel. If the TV cannot detect the TV channel corresponding to the broadcast frequency indicated by the CH/CC number, a “no-signal” picture appears.
56
MANUAL
1 Press the 6 buttons to choose a
programme number (PR) for a new TV channel
2 Press the blue button to activate
the MANUAL function
> MANUAL
BBC1 BBC2 ITV CH4 CH5
CH
CH 21 CH 22 CH 23 CH 24 CH 25 CH 26 CH 27 CH 28 CH 29
SEARCH+
SEARCH-
FINE-
FINE+
PR ID AV 01 02 03 04 05 06 07 08 09
OK
D0035-EK
To cancel the MANUAL function:
Press the b button.
3 When the COUNTRY setting is
UNITED KINGDOM: Continue to step 4
When the COUNTRY setting is IRELAND: Press the 3 button to choose the SYSTEM (broadcasting system) for a TV channel you want to register
If you do not know the correct broadcasting system, set the SYSTEM to “I”. If “I” is not correct, you will not hear the sound normally when the TV detects a TV channel. In this case, retry to set the SYSTEM correctly so that no problem arises.
4 Press the green or red button to
search for a TV channel
Scanning stops when the TV finds a TV channel. Then the TV channel is displayed.
5 Press the green or red button
repeatedly until the TV channel you want appears
If the TV channel reception is poor:
Press the blue or yellow button to fine­tune the TV channel.
6 Press the a button and register
the TV channel to a Programme number (PR)
The normal EDIT menu is resumed.
LT-32/26D50BJ/SJ / LCT1703-001B-U / ENGLISH
LT-32&26D50BJSJ_Eng.book Page 57 Thursday, October 7, 2004 4:42 PM
SET UP menu
CH/CC NUMBER
• When you want to use the INSERT function on page 56, find the CH/CC number corresponding to the channel number of the TV channel from this table. If you want to know a particular TV channel’s channel menu, look in TV listings magazines or contact the broadcaster.
• When the COUNTRY setting is UNITED KINGDOM, the CC number channels and the channels from CH 02 to CH 12 cannot be received.
CH Channel
CH 02 E2, IR A
CH 03 E3, IR B
CH 04 E4, IR C
CH 05 E5, IR D
CH 06 E6, IR E
CH 07 E7, IR F
CH 08 E8, IR G
CH 09 E9
CH 10 E10, IR H
CH 11 E11, IR J
CH 12 E12
CH 21 E21
CH 22 E22
CH 23 E23
CH 24 E24
CH 25 E25
CH 26 E26
CH 27 E27
CH 28 E28
CH 29 E29
CH 30 E30
CH 31 E31
CH 32 E32
CH 33 E33
CH 34 E34
CH 35 E35
CH 36 E36
CH 37 E37
CH 38 E38
CH 39 E39
CC Channel
CC 01 S1
CC 02 S2
CC 03 S3
CC 04 S4
CC 05 S5
CC 06 S6
CC 07 S7
CC 08 S8
CC 09 S9
CC 10 S10
CC 11 S11
CC 12 S12
CC 13 S13
CC 14 S14
CC 15 S15
CC 16 S16
CC 17 S17
CC 18 S18
CC 19 S19
CC 20 S20
CC 21 S21
CC 22 S22
CC 23 S23
CC 24 S24
CC 25 S25
CC 26 S26
CC 27 S27
CC 28 S28
CC 29 S29
CC 30 S30
CH Channel
CH 40 E40
CH 41 E41
CH 42 E42
CH 43 E43
CH 44 E44
CH 45 E45
CH 46 E46
CH 47 E47
CH 48 E48
CH 49 E49
CH 50 E50
CH 51 E51
CH 52 E52
CH 53 E53
CH 54 E54
CH 55 E55
CH 56 E56
CH 57 E57
CH 58 E58
CH 59 E59
CH 60 E60
CH 61 E61
CH 62 E62
CH 63 E63
CH 64 E64
CH 65 E65
CH 66 E66
CH 67 E67
CH 68 E68
CH 69 E69
CC Channel
CC 31 S31
CC 32 S32
CC 33 S33
CC 34 S34
CC 35 S35
CC 36 S36
CC 37 S37
CC 38 S38
CC 39 S39
CC 40 S40
CC 41 S41
CC 75 X
CC 76 Y
CC 77 Z
CC 78 Z+1
CC 79 Z+2
57
LT-32/26D50BJ/SJ / LCT1703-001B-U / ENGLISH
LT-32&26D50BJSJ_Eng.book Page 58 Thursday, October 7, 2004 4:42 PM
SET UP menu

DECODER (EXT-2)

If you have a decoder connected to a T-V LINK compatible VCR, which in turn is connected to the EXT-2 terminal, use the DECODER (EXT-2) function to unscramble the scrambled TV channels.
1 Turn on the decoder power
2 Display the scrambled TV channel
on the TV
Even if the decoder is working, a scrambled picture appears.
3 Display the SET UP menu and
choose DECODER (EXT-2)
SET UP
AUTO PROGRAM EDIT/MANUAL DECODER(EXT-2) COMPONENT AUTO SELECT EXT SETTING
OK
D0029
-EN
4 Press the 5 buttons to choose
ON
An unscrambled picture appears.
To cancel the DECODER (EXT-2) function:
Press the 5 buttons to choose OFF.
5 Press the a button to complete
the setting
The T-V LINK menu appears.
T-V LINK
DOWNLOAD TV RECORDING DEVICE
OK
D0005-EN
EXIT
You can send the programme numbers data to a VCR with the T-V LINK function.
OFF OFF
6 Turn on the VCR, and then press
the a button to transmit the data to recording device
The T-V LINK menu disappears once the data transmission ends.
If the DECODER (EXT-2) function has been set to “ON” but the TV channel cannot be unscrambled, check the following:
• Has the decoder been connected to the VCR properly according to the VCR and decoder instruction manuals?
• Has the decoder power been turned on?
• Can the TV channel be unscrambled with a decoder?
• Do you need to change the recording device settings in order to connect the decoder? Confirm that the VCR is set properly by rechecking the VCR instruction manual.

COMPONENT AUTO SELECT

When a external device that can output a component signal is connected to the EXT-4 component terminal and the connected device is played back, the TV input is automatically changed to EXT-4.
ON:
When the device connected to EXT-4 is played back, the TV input is automatically changed to EXT-4.
OFF:
Even when the device connected to EXT-4 is played back, the TV input is not changed. (Set to OFF when shipped from the factory.)
• This function automatically changes the TV input to EXT-4 when the TV detects a component input signal from the device connected to the EXT-4.
• When set to ON, the TV input may be automatically changed to EXT-4 just by an operation such as turning the power on, removing a disc, or another operation with a device (such as a DVD player).
• The COMPONENT AUTO SELECT function does not work when you are watching Digital terrestrial broadcasting (DVB-T) or a PC picture.
58
LT-32/26D50BJ/SJ / LCT1703-001B-U / ENGLISH
LT-32&26D50BJSJ_Eng.book Page 59 Thursday, October 7, 2004 4:42 PM
SET UP menu

EXT SETTING

1 Choose EXT SETTING, then press
the a or 3 button
The EXT SETTING menu appears.
> EXT SETTING
EXT-1
EXT-3
TV
DTV
OK
D0020-EN
2 Follow the instructions for the
function you want to use and operate the function
S-IN:
You can enjoy the high-quality picture of the 2 S-VIDEO signal (Y/C signal).
ID LIST:
You can have a name for each of the devices connected for each EXT terminal.
DUBBING:
You can choose a signal source to be output from an EXT-2 terminal.
S-IN (S-VIDEO input)
You can connect a device (such as an S-VHS VCR) to enjoy the high-quality picture of the S-VIDEO signal (Y/C signal).
Preparation:
• First read the device’s instruction manual and “Additional preparation” on page 63 to connect the device to the TV properly. Second, follow the device’s instruction manual to set the device so that it sends an S-VIDEO signal (Y/C signal) to the TV.
• Do not set S-IN (S-VIDEO input) to an EXT terminal connected to a device which cannot output an S-VIDEO (Y/C signal).
DUBBING EXT-2
EXT-4
ID LIST
S-IN
1 Press the 5 or 6 buttons to
choose an EXT terminal
> EXT SETTING
EXT-1
EXT-3
TV
DTV
OK
D0020-EN
DUBBING EXT-2
EXT-4
ID LIST
S-IN
2 Press the yellow button and set the
S-IN (S-VIDEO input). Then press the a button
An S-IN (S-VIDEO input) mark is displayed. You can view an S-VIDEO signal (Y/C signal) instead of the regular video signal (composite signal).
To cancel the S-IN (S-VIDEO input) setting:
Press the yellow button and turn off S-IN (S­VIDEO input) mark. The regular video signal (composite signal) pictures are resumed.
• Setting S-IN (S-VIDEO input) changes the head character from “E” to “S”. When an EXT terminal receives a normal video signal, “E1”, “E2” or “E3” appears on the display. This changes to “S1”, “S2” or “S3” when it receives an S-VIDEO signal.
• Even a device which can output an S-VIDEO signal (Y/C signal) may output a regular video signal (composite signal) depending on the device setting. If a picture cannot appear because the S-IN (S-VIDEO input) setting has been made, read the device instruction manual carefully again to check for the device settings.
59
LT-32/26D50BJ/SJ / LCT1703-001B-U / ENGLISH
LT-32&26D50BJSJ_Eng.book Page 60 Thursday, October 7, 2004 4:42 PM
SET UP menu
ID LIST
You can store a name for each of the devices connected to each EXT terminal. Giving a name to an EXT terminal makes the EXT terminal number appear on the screen, together with its name.
1 Press the 5 or 6 buttons to
choose an EXT terminal
2 Press the blue button to display the
name list (ID LIST)
> EXT SETTING
EXT-1
EXT-3
TV
DTV
OK
D0021-EN
DUBBING EXT-2
EXT-4
3 Press the 6 buttons to choose a
name. Then press the a button
The ID LIST disappears and the name is assigned to the EXT terminal.
• You cannot assign an EXT terminal name not found in the name list (ID LIST).
To erase a name assigned to the EXT terminal:
Choose a blank space.
4 Press the a button to complete
the setting
ID LIST
VHS S-VHS DVC CAM SAT STB GAME DVD DVR
DUBBING
You can choose a signal source to be output from the EXT-2 terminal.
You can do this with the output signals of the devices connected to other EXT terminals, or with the picture and sound from a TV channel you are currently viewing.
Caution:
Every time you dub, check this DUBBING setting beforehand. This setting may change automatically when “Timers (DTV Timer Recording)” or “Direct Rec” of the T-V LINK function is used.
1 Press the 5 buttons to choose
the arrow from the menu
> EXT SETTING
EXT-1
EXT-3
TV
DTV
OK
D0022-EN
2 Press the 6 buttons to choose an
EXT terminal or TV. Then press the a button
The arrow in the menu represents a signal flow. The left side of the arrow shows a signal source output from the EXT-2 terminal.
EXT-1/EXT-3:
The output signal of the device connected to an EXT terminal passes through the TV and is output from the EXT-2 terminal.
TV:
The picture and sound of the Analogue terrestrial broadcasting TV channel you are currently viewing are output from the EXT-2 terminal.
DUBBING EXT-2
EXT-4
60
LT-32/26D50BJ/SJ / LCT1703-001B-U / ENGLISH
LT-32&26D50BJSJ_Eng.book Page 61 Thursday, October 7, 2004 4:42 PM
DTV:
The picture and sound of the Digital terrestrial broadcasting (DVB-T) TV channel you are currently viewing are output from the EXT-2 terminal.
• During dubbing, you cannot turn off the TV. Turning off the TV also turns off the output from the EXT-2 terminal.
• When you choose an EXT terminal as an output, you can view a TV programme or a picture from the other EXT terminal while dubbing the picture from a device connected to the EXT terminal onto a VCR connected to the EXT-2 terminal.
• The RGB signals from TV games cannot be output. Teletext programmes cannot be output.
SET UP menu
61
LT-32/26D50BJ/SJ / LCT1703-001B-U / ENGLISH
LT-32&26D50BJSJ_Eng.book Page 62 Thursday, October 7, 2004 4:42 PM

Displaying a computer screen

This TV can be used as a computer screen.

Connecting to the computer

Use a D-SUB cable to connect the TV’s PC IN terminal to the computer’s analogue RGB output terminal. If you want to listen to the sound from the computer, use an audio cable to connect the EXT-3 L/R terminal to the computer’s sound output terminal. When the sound from the computer is mono, connect to the EXT-3 L terminal.
• Refer to the computer manual for a detailed explanation of the connections at the computer side.
• Ensure that the connectors are facing the correct way when connecting.
• After connecting the D-SUB cable, tighten the two screws to fix the connector in place.

Watching images from a computer

After starting the computer, press the G or p p buttons to choose “PC”
“PC” is after EXT-4. You can listen to the sound when the sound from the computer is connected to the EXT-3 L/R terminal.
• When the sound from the computer is connected to EXT-3, by choosing external input EXT-3 the sound from the computer can be listened to, but the images from the computer cannot be seen.

Table of signals for each type of computer

Resolution Vertical
640 × 480 (VGA)
1024 × 768 (XGA)
* Only the above formats are supported. * Even with the above formats and at
60 Hz, some problems may be experienced depending on the quality of the synchronous signal. (Depending on the quality, some pictures may not be displayed properly.)
* Apple Macintosh
supported.
When a picture is not displayed
Check the computer’s refresh rate and set it to 60 Hz. Refer to the computer’s instruction manual. Computers which cannot have their refresh rate set to 60 Hz cannot be used with this unit.
frequency (Hz)
60.0 31.5
60.0 42.0
*
computers are not
Horizontal frequency (kHz)
62
* Apple Macintosh is a registered
trademark of Apple Computer, Inc.
LT-32/26D50BJ/SJ / LCT1703-001B-U / ENGLISH
LT-32&26D50BJSJ_Eng.book Page 63 Thursday, October 7, 2004 4:42 PM

Additional preparation

Connecting external equipment

Connect the equipment to the TV, making the correct rear panel and front panel connections.
Before connecting anything:
• Read the manuals that came with the equipment. Depending on the equipment, the connection method may be different from the diagram. Also, the equipment settings may need to change depending on the connection method.
• Turn off all the equipment including the TV.
• The “Specifications” on the back cover give the details of the EXT terminals. If you are connecting equipment not listed in the following connection diagram, see the table to choose the best EXT terminal.
• Connecting cables are not supplied.
• When a device that can output component signals is connected to the EXT-4 component terminal, the TV input can be automatically changed to EXT-4 by just turning the power supply of the connected device on. For details, see “COMPONENT AUTO SELECT” in the SET UP menu on page 58.
Connecting the PC
For details, see “Connecting to the computer” on page 62.
1 VCR (composite signal) 2 VCR (composite signal/S-VIDEO signal) 3 T-V LINK compatible VCR (composite
signal/S-VIDEO signal)
4 Decoder 5 DVD player (composite signal/S-VIDEO
signal)
6 DVD player (composite signal/RGB
signal)
7 DVD player (component video signals;
Y/Pb/Pr)
8 TV game (composite signal/RGB signal) 9 TV game (composite signal/S-VIDEO
signal)
0 Headphones
- Camcorder (composite signal/S-VIDEO
signal)
= SCART cable ~ Audio cable ! Video cable @ S-VIDEO cable # Component cable
63
LT-32/26D50BJ/SJ / LCT1703-001B-U / ENGLISH
LT-32&26D50BJSJ_Eng.book Page 64 Thursday, October 7, 2004 4:42 PM
Additional preparation
without terminal covers
64
LT-32/26D50BJ/SJ / LCT1703-001B-U / ENGLISH
LT-32&26D50BJSJ_Eng.book Page 65 Thursday, October 7, 2004 4:42 PM
Additional preparation
Equipment which can output the
S-VIDEO signal (Y/C signal)
Connect the equipment to an EXT terminal (but not the EXT-4 terminal).
You can choose between an S-VIDEO signal (Y/C signal) and a regular video signal (composite signal). For details of how to operate the equipment, see “S-IN (S-VIDEO input)” on page 59.
T-V LINK compatible VCR
Be sure to connect the T-V LINK compatible VCR to the EXT-2 terminal. If not, the T-V LINK function will not work properly.
• When connecting a T-V LINK compatible VCR to the EXT-2 terminal, be sure to connect the decoder to the VCR. If not, the T-V LINK function may not work properly.
• When you connect the decoder to the VCR, after you have stored TV channels in the programme numbers (PR) list, set the DECODER (EXT-2) function for the programme number (PR) to ON to unscramble a scrambled TV channel. For details, see “DECODER (EXT-2)” on page 58.
Connecting headphones
Connect the headphones with a stereo mini­jack (3.5 mm diameter) to the headphone jack socket.
• No sound comes from the TV speakers when the headphones are connected and only one screen is displayed.
Video or sound signal output from
the EXT-2 terminal
You can change over the output of the video/ sound signal from the EXT-2 terminal. This is useful when you want to dub the video/ sound from another device onto the VCR connected to the EXT-2 terminal. For details on how to do this, see “DUBBING” on page 60.
• The signals from EXT-4 and PC IN terminal cannot be output from EXT-2.
TV output from the EXT-1 terminal
The video/sound signal of a Analogue terrestrial broadcasting channel you are viewing is always output from the EXT-1 terminal.
• Changing over a programme number (PR) also changes over the TV output from the EXT-1 terminal.
• The video/sound signal from an EXT terminal cannot be output.
• Teletext programmes cannot be output.
Connection when recording to
VCR
• When recording an Analogue terrestrial broadcasting, connect to either terminal EXT-1 or EXT-2. If you connect to the EXT-2 terminal, make sure the “DUBBING” setting (see page 60) is set to “TV”.
• Choose the EXT-2 terminal to connect to a T-V LINK compatible VCR. When recording an Analogue terrestrial broadcasting, set the “DUBBING” setting (see page 60) to “TV”. When recording a Digital terrestrial broadcasting (DVB-T), set the “DUBBING” setting (see page 60) to “DTV”.
65
LT-32/26D50BJ/SJ / LCT1703-001B-U / ENGLISH
LT-32&26D50BJSJ_Eng.book Page 66 Thursday, October 7, 2004 4:42 PM
Additional preparation
Connecting speakers/amplifier
While referring to the audio equipment connection diagram, connect the audio equipment you want to the TV. You can use external front speakers to listen to the TV sound instead of the TV speakers.
Before connecting anything:
• Read the manuals provided with the amplifier and speakers.
• Turn the TV and amplifier off.
• Note that connecting cables are not supplied.
without terminal covers
L
1 Amplifier 2 External speakers (Magnetic-shielded type)
R
• The output from the AUDIO OUT terminal is not interrupted by headphone connection to the TV. You cannot cut the sound from the front speaker even if you connect a headphone to the TV.
• Adjust the volume of the external speakers with the amplifier.

Operating a JVC brand VCR or DVD player

These buttons will operate a JVC brand VCR or DVD player. Pressing a button that looks the same as the device’s original remote control button has the same effect as the original remote control.
1 Set the VCR/TV/DVD Switch to the
VCR or DVD position
VCR:
When you are operating the VCR, set the switch to the VCR position.
• You can turn the VCR on or off with
the # (standby) button.
DVD:
When you are operating the DVD player, set the switch to the DVD position.
• You can turn the DVD player on or off
with the # (standby) button.
• You can also press the H or T button and display the DVD disc menu screen, and then operate by pressing the 7 buttons.
2 Press the VCR/DVD Control Button
to control your VCR or DVD player
• If your device is not made by JVC, these buttons will not work.
• Even if your device is made by JVC, some of these buttons may not work, depending on the device you are using.
• You can use the p buttons to choose a TV channel the VCR will receive, or choose the chapter the DVD player plays back.
• Some models of DVD player use the p buttons for both operating the fast forward/backward functions and for choosing the chapter. In this case, the 253 buttons do not work.
You cannot turn the TV on or off when the VCR/TV/DVD switch is set to the VCR or DVD position. When you turn the TV on or off, set the VCR/TV/DVD switch to the TV position.
66
LT-32/26D50BJ/SJ / LCT1703-001B-U / ENGLISH
LT-32&26D50BJSJ_Eng.book Page 67 Thursday, October 7, 2004 4:42 PM

Troubleshooting

Digital terrestrial broadcasting (DVB-T) service area
Although this TV can receive both Digital terrestrial broadcasting (DVB-T) and Analogue terrestrial broadcasting, depending on the area in which you live, you may not be able to receive Digital terrestrial broadcasting (DVB-T). For details of the Digital terrestrial broadcasting (DVB-T) service area, refer to the FREEVIEW website etc.
If a problem arises while you are using the TV, please read this troubleshooting guide carefully before you ask to have the TV repaired. You may be able to fix it easily by yourself. For example, if the mains plug is disconnected from the mains outlet, or the TV aerial has problems, you may think there is a problem with the TV itself.
Important:
• This troubleshooting guide only covers problems whose causes are not easy to decide. If you have a question when you are operating a function, read the page(s) for that function carefully, not this troubleshooting guide.
• If you follow the advice in this troubleshooting guide without any success, unplug the mains plug and ask for your TV to be repaired. Do not attempt to repair the TV by yourself or to remove the rear cover of the TV.
If you cannot turn on the TV
• Is the mains plug connected to the mains outlet?
• Make sure you set the VCR/TV/DVD switch to the TV position. You cannot turn the TV on when the VCR/TV/DVD switch is set to the VCR or DVD position.
If you cannot turn off the TV
• Make sure you set the VCR/TV/DVD switch to the TV position. You cannot turn the TV off when the VCR/TV/DVD switch is set to the VCR or DVD position.
No picture or no sound
• Have you chosen a TV channel with very poor reception? If so, the BLUE BACK function will be activated: the entire screen becomes blue, and the sound is muted. If you still want to view the TV channel, follow the description “BLUE BACK” on page 52 to change the BLUE BACK function setting to OFF.
• If the SYSTEM setting for a TV channel is incorrect, it may prevent the sound from being issued. Follow the description “EDIT/MANUAL (Analogue)” on page 53 to use the MANUAL function to try to change the SYSTEM setting.
Poor picture
• If the Digital terrestrial broadcasting (DVB-T) picture is unnatural, press the TV/AV button and MENU/OK button at the same time. The power will turn off and then on again, after which the picture may appear natural again.
• If noise (snow) totally blocks out the picture, there may be a problem with the aerial or aerial cable. Check the following to try to solve the problem:
– Have the TV and aerial been connected
properly? – Has the aerial cable been damaged? – Is the aerial pointing in the right
direction? – Is the aerial itself faulty?
• If the TV or aerial suffers interference from other equipment, stripes or noise may appear in the picture. Move any equipment such as an amplifier, personal computer, or a hair drier, that can cause interference away from your TV. Or try moving the TV. If the aerial suffers interference from a radio tower or high­voltage wire, please contact your local dealer.
67
LT-32/26D50BJ/SJ / LCT1703-001B-U / ENGLISH
LT-32&26D50BJSJ_Eng.book Page 68 Thursday, October 7, 2004 4:42 PM
Troubleshooting
• If the TV suffers interference from signals reflecting from mountains or buildings, double-pictures (ghosting) will occur. Try to change the aerial’s direction or replace it with one with better directionality.
• Are your COLOUR SYSTEM settings correct? Follow the description “COLOUR SYSTEM” on page 48 to try to solve the trouble.
• Have the COLOUR and BRIGHT settings been adjusted properly? Follow the description “BRIGHT-2” and “COLOUR” on page 45 to try to adjust them properly.
• Videotaping teletext is not recommended because it may not record correctly.
• When viewing images from commercially available video software products, or videos from videotapes which have been recorded improperly, the top of the image may be distorted. This is due to the condition of the video signal. There is nothing wrong with the TV.
• Since this TV is designed to make full use of the resolution of the original video source, the motion may appear unnatural when the video source is input with 625p progressive-scanning component signals. If this occurs, change the output setting of the connected device to 625i interlace­scanning component signal output. See the instructions that came with the device for more information.
Poor sound
• Have you adjusted BASS or TREBLE properly? If not, follow the description “BASS” or “TREBLE” on page 49.
• When TV channel reception is poor, it can be hard to hear stereo or bilingual sound. In this case, follow the description “STEREO / I • II” on page 49 to hear the sound more easily by changing it to a mono sound.
If the TV does not respond to the
remote control
• Have the batteries of the remote control worn out? Follow the description “Putting the batteries into the remote control” on page 10 and replace them with new batteries.
68
• Have you attempted to use the remote control from the sides or rear of the TV or from more than seven metres away from the TV? Use the remote control in front of your TV or from less than seven metres away.
• When you are viewing a teletext programme, you cannot operate the menus. Press the TV/DTV button to return to the ordinary TV programme, and then try operating the menus.
• If the TV suddenly stops responding, disconnect the power cord of the TV from the AC outlet. Connect them to the AC outlet again to turn on the TV. If the TV returns to a normal state, it is not a failure.
Other issues
• When the SLEEP TIMER function operates, the TV is automatically turned off. If the TV suddenly turns off, try to press the # (standby) button to turn on the TV once again. If the TV goes back to normal, there is no problem.
• When the TV is receiving a wide-screen signal (WSS) or a signal from an external device affecting the screen size, the ZOOM mode automatically changes. When you want to resume the previous ZOOM mode, press the c button again.
• It takes a short period of time from the time an operation such as changing channels is performed until an image is displayed. This is not a fault. This is the time needed for the image to stabilise before it can be displayed.
• The TV may make a crackling sound due to a sudden change in temperature. The picture or sound may be normal. If you hear crackling sounds frequently while you are viewing the TV, there may be other causes. As a precaution, ask your service technician to inspect it.
LT-32/26D50BJ/SJ / LCT1703-001B-U / ENGLISH
LT-32&26D50BJSJ_Eng.book Page 69 Thursday, October 7, 2004 4:42 PM
• The top of the TV and the screen may become hot during use but this has no affect on the performance of the TV. Make sure that the ventilation holes are not blocked.
• When the picture is unstable, the screen may become white for a moment. This happens when the signal which drives the liquid crystal is missing. This is not a fault.
• When a still image has been displayed for a long period, a faint residual image may remain on the screen for a short time after the power has been turned off or when another image is displayed. This is not a fault and the image will eventually disappear.
Troubleshooting
69
LT-32/26D50BJ/SJ / LCT1703-001B-U / ENGLISH
LT-32&26D50BJSJ_Eng.book Page 70 Thursday, October 7, 2004 4:42 PM

Specifications

Model LT-32D50BJ/LT-32D50SJ COUNTRY setting
Broadcasting systems CCIR, I CCIR B/G, I, D/K, L Colour systems PAL
Channels and frequencies Analogue: E21-E69, Digital: 474 MHz -
Sound-multiplex systems NICAM (I) system, Digital (DVB-T):
Teletext systems FLOF (Fastext),
Power requirements 110 - 240 V AC, 50/60 Hz Power consumption 170 W (Standby: 2.6 W) Screen size Viewable area 80 cm (measured diagonally) Audio output Rated Power output: 10 W + 10 W Speakers 6.6 cm round × 2 EXT-1 terminal Euroconnector (21-pin, SCART)
EXT-2 terminal Euroconnector (21-pin, SCART)
EXT-3 terminal RCA connectors × 3
EXT-4 terminal RCA connectors × 5
AUDIO OUT terminal RCA connectors × 2
PC INPUT terminal Analogue RGB D-SUB (15 pin) × 1
Headphone jack Stereo mini-jack (3.5 mm in diameter) Dimensions (W × H × D) 834.1 mm × 637 mm × 295 mm
Weight 19.8 kg
Accessories Remote control unit × 1 (RM-C1813H)
When the COUNTRY setting is
UNITED KINGDOM
• The EXT terminals also support the NTSC 3.58/4.43 MHz system.
850 MHz (channel 21 - 68)
MHEG 5 UK profile
WST (World Standard System)
• Video input, S-VIDEO (Y/C) input, Audio L/R inputs and RGB inputs are available.
• TV broadcast outputs (Video and Audio L/R) are available.
• Video input, S-VIDEO (Y/C) input, Audio L/R inputs and RGB inputs are available.
• Video and Audio L/R outputs are available.
• T-V LINK functions are available.
S-VIDEO connector × 1
• Video input, S-VIDEO (Y/C) input and Audio L/R inputs are available.
• Component video (Y, Pb, Pr) input and Audio L/R inputs are available.
• 625p, 525p, 1125i and 750p signals are available. 750p signal is only available for 60Hz.
• Some DVD players can output 625p and 525p signals.
• 1125i and 750p are new high-definition signals.
• Audio L/R outputs are available.
• Output level 0.5 Vrms.
• PC signal is available. Refer to page 62 for details of the signals which can be input.
834.1 mm × 567.7 mm × 107.5 mm (without stand)
17.3 kg (without stand)
AA/R6 dry cell battery × 2
When the COUNTRY setting is
IRELAND
PAL, SECAM
• The EXT terminals also support the NTSC 3.58/4.43 MHz system.
IR A-J, E2-E12, E21-E69, S1-S41, X, Y, Z, Z+1, Z+2
NICAM (B/G, I, D/K, L) system, A2 (B/G, D/K) system
FLOF (Fastext), TOP, WST (World Standard System)
We may change the design and specifications without notice.
Pictures displayed on the screen using this TV’s ZOOM functions should not be shown for any commercial or demonstration purpose in public places (cafes, hotels, etc.) without the consent of the owners of copyright of the original picture sources, as this would be an infringement of copyright.
70
LT-32/26D50BJ/SJ / LCT1703-001B-U / ENGLISH
LT-32&26D50BJSJ_Eng.book Page 71 Thursday, October 7, 2004 4:42 PM
Specifications
Model LT-26D50BJ/LT-26D50SJ COUNTRY setting
Broadcasting systems CCIR, I CCIR B/G, I, D/K, L Colour systems PAL
Channels and frequencies Analogue: E21-E69, Digital: 474 MHz -
Sound-multiplex systems NICAM (I) system, Digital (DVB-T):
Teletext systems FLOF (Fastext),
Power requirements 110 - 240 V AC, 50/60 Hz Power consumption 135 W (Standby: 2.6 W) Screen size Viewable area 64.8 cm (measured diagonally) Audio output Rated Power output: 10 W + 10 W Speakers 6.6 cm round × 2 EXT-1 terminal Euroconnector (21-pin, SCART)
EXT-2 terminal Euroconnector (21-pin, SCART)
EXT-3 terminal RCA connectors × 3
EXT-4 terminal RCA connectors × 5
AUDIO OUT terminal RCA connectors × 2
PC INPUT terminal Analogue RGB D-SUB (15 pin) × 1
Headphone jack Stereo mini-jack (3.5 mm in diameter) Dimensions (W × H × D) 702.5 mm × 560 mm × 295 mm
Weight 15.5 kg
Accessories Remote control unit × 1 (RM-C1813H)
When the COUNTRY setting is
UNITED KINGDOM
• The EXT terminals also support the NTSC 3.58/4.43 MHz system.
850 MHz (channel 21 - 68)
MHEG 5 UK profile
WST (World Standard System)
• Video input, S-VIDEO (Y/C) input, Audio L/R inputs and RGB inputs are available.
• TV broadcast outputs (Video and Audio L/R) are available.
• Video input, S-VIDEO (Y/C) input, Audio L/R inputs and RGB inputs are available.
• Video and Audio L/R outputs are available.
• T-V LINK functions are available.
S-VIDEO connector × 1
• Video input, S-VIDEO (Y/C) input and Audio L/R inputs are available.
• Component video (Y, Pb, Pr) input and Audio L/R inputs are available.
• 625p, 525p, 1125i and 750p signals are available. 750p signal is only available for 60Hz.
• Some DVD players can output 625p and 525p signals.
• 1125i and 750p are new high-definition signals.
• Audio L/R outputs are available.
• Output level 0.5 Vrms.
• PC signal is available. Refer to page 62 for details of the signals which can be input.
702.5 mm × 490.7 mm × 106.8 mm (without stand)
13.0 kg (without stand)
AA/R6 dry cell battery × 2
When the COUNTRY setting is
IRELAND
PAL, SECAM
• The EXT terminals also support the NTSC 3.58/4.43 MHz system.
IR A-J, E2-E12, E21-E69, S1-S41, X, Y, Z, Z+1, Z+2
NICAM (B/G, I, D/K, L) system, A2 (B/G, D/K) system
FLOF (Fastext), TOP, WST (World Standard System)
We may change the design and specifications without notice.
Pictures displayed on the screen using this TV’s ZOOM functions should not be shown for any commercial or demonstration purpose in public places (cafes, hotels, etc.) without the consent of the owners of copyright of the original picture sources, as this would be an infringement of copyright.
71
LT-32/26D50BJ/SJ / LCT1703-001B-U / All Cover
© 2004 Victor Company of Japan, Limited
LCT1703-001B-U 1004MKH-CR-MU
Cover04
Loading...