JVC KD-SH55 User Manual 2
CD RECEIVER KD-SH77/KD-SH55
ENGLISH
RECEPTOR CON CD KD-SH77/KD-SH55
RECEPTEUR CD KD-SH77/KD-SH55
KD-SH77
Detachable
ATT
ANGLE
EQ
CD
DAB
DISC
FM
AM
CH
AUX SEL
RM-RK100
For installation and connections, refer to the separate manual.
Para la instalación y las conexiones, refiérase al manual separado.
Pour l’installation et les raccordements, se référer au manuel séparé.
PRESET
PRESET
R D
DISC
VOLUME
KD-SH55
ESPAÑOL
FRANÇAIS
INSTRUCTIONS
MANUAL DE INSTRUCCIONES
MANUEL D’INSTRUCTIONS
For customer Use:
Enter below the Model No. and
Serial No. which are located on
the top or bottom of the cabinet.
Retain this information for future
reference.
Model No.
Serial No.
LVT0623-001A
[J]
INFORMATION (For U.S.A.)
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
ENGLISH
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
– Consult the dealer or an experienced radio/TV technician for help.
IMPORTANT FOR LASER PRODUCTS
Precautions:
1. CLASS 1 LASER PRODUCT
2. DANGER: Invisible laser radiation when open and interlock failed or defeated. Avoid direct
exposure to beam.
3. CAUTION: Do not open the top cover. There are no user-serviceable parts inside. Leave all
servicing to qualified service personnel.
4. CAUTION: This CD player uses invisible laser radiation, however, is equipped with safety switches
to prevent radiation emission when unloading CDs. It is dangerous to defeat the safety switches.
5. CAUTION: Use of controls, adjustments or performance of procedures other than those specified
herein may result in hazardous radiation exposure.
How to reset your unit
Press the reset button on the front panel using a
ball-point pen or similar tool.
Note:
Your preset adjustments – such as preset channels or
sound adjustments – will also be erased.
BEFORE USE
*
For safety....
• Do not raise the volume level too much, as this will
block outside sounds, making driving dangerous.
• Stop the car before performing any complicated
operations.
2
CAUTION:
NEVER insert your finger between the
control panel and the unit, as it may get
caught and hurt. (See page 22.)
*
Temperature inside the car....
If you have parked the car for a long time in hot or
cold weather, wait until the temperature in the car
becomes normal before operating the unit.
Thank you for purchasing a JVC product. Please read all instructions carefully before operation,
to ensure your complete understanding and to obtain the best possible performance from the unit.
CONTENTS
How to reset your unit............................... 2
LOCATION OF THE BUTTONS............ 4
Control panel ........................................... 4
Remote controller .................................... 5
Preparing the remote controller ................ 6
BASIC OPERATIONS ...................... 7
RADIO BASIC OPERATIONS ............. 8
Listening to the radio ................................ 8
Storing stations in memory ....................... 9
Tuning into a preset station ...................... 10
CD OPERATIONS .......................... 11
Playing a CD............................................ 11
Playing a CD text..................................... 12
Locating a track or particular portion
on a CD ................................................. 12
Selecting CD playback modes ................. 13
Prohibiting CD ejection ............................. 13
SOUND ADJUSTMENTS .................. 14
Adjusting the sound ................................. 14
Reinforcing the bass sound ...................... 14
Selecting preset sound modes ................. 15
Storing your own sound adjustments ....... 16
OTHER MAIN FUNCTIONS ............... 17
Setting the clock ...................................... 17
Changing the general settings (PSM) ...... 17
Assigning names to the sources .............. 21
Changing the control panel angle............. 22
Detaching the control panel...................... 23
EXTERNAL COMPONENT OPERATIONS.. 24
Playing external components ................... 24
CD CHANGER OPERATIONS ............. 26
Playing CDs ............................................. 26
Selecting CD playback modes.................. 27
ADDITIONAL INFORMATION............. 28
MAINTENANCE ............................ 29
Handling CDs .......................................... 29
TROUBLESHOOTING...................... 30
SPECIFICATIONS.......................... 31
ENGLISH
About the demonstration mode (DEMO MODE)...
When shipped from the factory, “DEMO MODE” is set to “DEMO ON” in this unit.
The following demonstration, introducing the main features equipped with this unit, will appear on the
display automatically if no sound comes in for 3 minutes. (See page 20.)
• 24bit DAC : (24 bit digital-analog converter: Gives you a high quality sound after D/A
conversion.)
• HS TUNER : (High-sensitivity Tuner: Enables a fine reception of stations.)
• EQUALIZER : (Allows you to fine-adjust the sound to match your preference.)
• SUB WOOFER : (ONLY for KD-SH77: Enables you to connect a subwoofer and to adjust its
output level.)
CAUTION on Volume Setting
CDs produce very little noise compared with other sources. If the volume level is adjusted for the tuner, for
example, the speakers may be damaged by the sudden increase in the output level. Therefore, lower the
volume before playing a disc and adjust it as required during playback.
3
LOCATION OF THE BUTTONS
Control panel
1
ENGLISH
1 (eject) button
2 Control dial
3 SEL (select) button
4 EQ (equalization) button
5 S.BASS (S) (super bass) button
6 DISP (D) (display) button
7 BAND (B) button
8 MODE (M) button
9 ¢ / 4 buttons
•
Also functions as SSM buttons when pressed
together.
p ATT (angle / attenuator) button
2
3
4 5
t
6
7
8
9
ry
q MP3 INPUT jack
w (control panel release) button
e Remote sensor
r Number buttons
• MO (monaural) button
• LO (local) button
• INT (intro scan) button
• RPT (repeat) button
• RND (random) button
• Video component operation buttons
(ONLY for KD-SH77)
t SOURCE (standby / on) button
y Reset button
e
p
w
q
How to use the number buttons:
If you press MODE (M), the unit goes into functions mode and the number buttons work as different
function buttons.
Normally
Equalizing
During
functions mode
To use these buttons as number buttons again after pressing MODE (M), wait for 5 seconds
without pressing any number button until the functions mode is cleared.
• Pressing MODE (M) again also clears the functions mode.
4
pattern indicator
Time countdown
indicator
Remote controller
ATT
1
ANGLE
CD
2
DAB
FM
AM
DISC
PRESET
R D
EQ
PRESET
3
4
5
6
7
3 Changes the angle of the control panel in three
positions.
4 Selects the sound modes.
Each time you press the button, sound modes
change.
5 • Searches for stations while listening to the
radio.
• Fast-forwards or reverses the track if pressed
and held while listening to a CD.
• Skips to the beginning of the next track or goes
back to the beginning of the current (or
previous tracks) if pressed briefly while
listening to a CD.
ENGLISH
CH
AUX SEL
DISC
VOLUME
8
9
RM-RK100
The R•D button does not function
for this model.
1 • Turns on the unit if pressed when the unit is
turned off.
• T urns off the unit if pressed and held until “SEE
YOU” appears on the display.
• Drops the volume lev el if pressed briefly, and
“ATT” flashes on the display.
Press again to resume the volume.
2 • CD : Selects CD player.
• FM : Selects FM tuner.
• AM : Selects AM tuner.
• CH : Selects CD changer.*
• AUX : Selects the external components.
Each time you press the button, FM
band (FM1, FM2 and FM3) changes.
•
Does not function as the DAB button.
Each time you press the button, “AUX
INPUT” and “LINE INPUT”** are
alternately selected.
6 Changes the preset channel number while
listening to the radio.
Each time you press the button, the preset
channel number changes, and the selected
station is tuned into.
7 Changes the disc number while listening to the
CD changer.
Each time you press the button, the disc
number changes, and the selected disc start
playing.
8*** Selects the sound adjustment items.
Each time you press the button, the items
change.
9*** • Changes the volume.
• Adjusts the sound mode (after SEL is
pressed).
* Without connecting the CD changer, you cannot
select it as the source to play.
** ONLY for KD-SH55: To select the external
component, you have to change the external
component setting (see page 18).
***These buttons do not function for the preferred
setting mode adjustment.
5
Preparing the remote controller
Before using the remote controller:
• Aim the remote controller directly at the remote
sensor on the main unit. Make sure there is no
ENGLISH
obstacle in between.
2. Place the battery.
Slide the battery into the holder with the + side
facing upwards so that the battery is fixed in
the holder.
Lithium coin battery
(product number:
CR2025)
3. Return the battery holder.
Insert again the battery holder pushing it until
you hear a clicking sound.
Remote sensor
• Do not expose the remote sensor to strong
light (direct sunlight or artificial lighting).
Installing the battery
When the controllable range or effectiveness of the
remote controller decreases, replace the battery.
1. Remove the battery holder.
1) Push out the battery holder in the direction
indicated by the arrow using a ball-point
pen or a similar tool.
2) Remove the battery holder.
(back side)
1)
2)
(back side)
WARNING:
• Store the battery in a place where children cannot
reach.
If a child accidentally swallows the battery,
consult a doctor immediately.
• Do not recharge, short, disassemble or heat the
battery or dispose of it in a fire.
Doing any of these things may cause the battery to
give off heat, crack or start a fire.
• Do not leave the battery with other metallic
materials.
Doing this may cause the battery to give off heat,
crack or start a fire.
• When throwing away or saving the battery, wrap it
in tape and insulate; otherwise, the battery may
start to give off heat, crack or start a fire.
• Do not poke the battery with tweezers or similar
tools.
Doing this may cause the battery to give off heat,
crack or start a fire.
6
2
1
1
Turn on the power and select the
source.
When you press the button
for the first time, the power
comes on. Then each time
you press the button, the
source changes as follows.
For KD-SH77
FM TUNER
or
AM TUNER
CD PLAY CD CHANGER
*
LINE INPUTAUX INPUT
BASIC OPERATIONS
Note:
When you use this unit for
the first time, set the built-in
clock correctly, see page 17.
2
Adjust the volume.
To increase the volume.
To decrease the volume.
**
Volume level appears.
ENGLISH
For KD-SH55
FM TUNER
or or
AM TUNER
* If a CD is not in the loading slot, you cannot
select CD as the source to play.
** Without connecting the CD changer, you
cannot select it as the source to play.
***ONLY for KD-SH55: To select the external
component, you have to change the external
component setting (see page 20).
To operate the tuner (FM or AM),
see pages 8 – 10.
To operate the CD player,
see pages 11 – 13.
To operate external components
(AUX INPUT and LINE INPUT),
see pages 24 – 25.
To operate the CD changer,
see pages 26 – 27.
CD PLAY CD CHANGER
*
LINE INPUT
AUX INPUT
Volume level indicator
**
***
Note:
After adjusting the volume, you can push in the
control dial to avoid unintended operations.
To use it again, push the control dial again to
make it come out.
3
Adjust the sound as you want.
(See page 14.)
To drop the volume in a moment
Press and hold /ATT while listening to any
source. “ATT” starts flashing on the display, and
the volume level will drop in a moment.
To resume the previous volume level, press and
hold the button again.
• If you turn the control dial clockwise, you can
also restore the sound.
To turn off the power
Press and hold SOURCE until “SEE YOU”
appears on the display.
7
ENGLISH
RADIO BASIC OPERATIONS
Listening to the radio
You can use either automatic searching or
manual searching to tune into a particular station.
Searching a station automatically:
Auto search
1
Select the band (FM1 – 3, AM).
1 Press SOURCE
repeatedly to select the
tuner as the source.
2 If necessary, press
BAND (B) repeatedly to
select FM or AM. Each
time you press the
button, the band changes
as follows:
FM 1 FM 2 FM 3 AM
Selected band appears.
Note:
This receiver has three FM bands (FM1, FM2,
FM3). You can use any one of them to listen to
an FM broadcast.
2
Start searching a station.
Press ¢ to search
stations of higher
frequencies.
Press 4 to search
stations of lower
frequencies.
8
When a station is received, searching stops.
To stop searching before a station is received,
press the same button you have pressed for
searching.
To turn in FM stations only with strong signals
1 Press MODE (M) to enter the functions mode
while listening to an FM broadcast.
2 Press LO (local) while still in the functions
mode, so that the LOCAL indicator lights up on
the display.
This function works only while searching FM
stations, including SSM preset.
Each time you press the button, the LOCAL
indicator lights up and goes off alternately.
Searching a station manually:
Manual search
1
Select the band (FM1 – 3, AM).
1 Press SOURCE
repeatedly to select tuner
as the source.
2 If necessary, press
BAND (B) repeatedly to
select FM or AM. Each
time you press the
button, the band
changes as follows:
FM 1 FM 2 FM 3 AM
Note:
This receiver has three FM bands (FM1, FM2,
FM3). You can use any one of them to listen to
an FM broadcast.
2
Press and hold ¢ or 4 until
“M” (manual) starts flashing on the
display.
Selected band appears.
3
Tune into a station you want while “M”
is flashing.
Press ¢ to tune
into stations of higher
frequencies.
Press 4 to tune
into stations of lower
frequencies.
• If you release your finger from the button,
the manual mode will automatically turn off
after 5 seconds.
• If you hold down the button, the frequency
keeps changing until you release the
button.
When an FM stereo broadcast is hard to
receive:
1 Press MODE (M) to enter the
functions mode while listening to
an FM stereo broadcast.
2 Press MO (monaural) while still in
the functions mode, so that the
MO indicator lights up on the
display.
• Each time you press the button,
the MO indicator lights up and
goes off alternately.
Lights up when receiving
an FM broadcast in stereo.
The MO indicator lights
up.
Storing stations in memory
You can use one of the following two methods to
store broadcasting stations in memory.
• Automatic preset of FM stations: SSM (Strongstation Sequential Memory)
• Manual preset of both FM and AM stations
FM station automatic preset: SSM
You can preset 6 local FM stations in each FM
band (FM1, FM2 and FM3).
1
Select the FM band (FM1 – 3) you want
to store FM stations into.
1 Press SOURCE
repeatedly to select the
tuner as the source.
2 If necessary, press
BAND (B) repeatedly to
select the FM band.
Each time you press the
button, the band changes
as follows:
FM 1 FM 2 FM 3 AM
2
Press and hold both buttons for more
than 2 seconds.
“SSM” appears, then
disappears when automatic
preset is over.
Local FM stations with the strongest signals are
searched and stored automatically in the band
number you have selected (FM1, FM2 or FM3).
These stations are preset in the number buttons
— No.1 (lowest frequency) to No.6 (highest
frequency).
When automatic preset is over, the station stored
in number button 1 will be automatically tuned in.
ENGLISH
When the MO indicator is lit on the display, the
sound you hear becomes monaural but the
reception will be improved (the ST indicator
goes off).
9
Manual preset
You can preset up to 6 stations in each band
(FM1, FM2, FM3 and AM) manually.
Ex.: Storing an FM station of 88.3 MHz into the
ENGLISH
preset number 1 of the FM1 band
1
Select the band (FM1 – 3, AM) you
want to store stations into (in this
example, FM1).
1 Press SOURCE
repeatedly to select the
tuner as the source.
2 If necessary, press
BAND (B) repeatedly to
select FM or AM. Each
time you press the
button, the band
changes as follows:
FM 1 FM 2 FM 3 AM
2
Tune into a station of 88.3 MHz.
Press ¢ to tune
into stations of higher
frequencies.
Press 4 to tune
into stations of lower
frequencies.
Tuning into a preset station
You can easily tune into a preset station.
Remember that you must store stations first. If
you have not stored them yet, see “Storing
stations in memory” on page 9.
1
Select the band (FM1 – 3, AM).
1 Press SOURCE
repeatedly to select the
tuner as the source.
2 If necessary, press
BAND (B) repeatedly to
select FM or AM. Each
time you press the
button, the band changes
as follows:
FM 1 FM 2 FM 3 AM
2
Select the number (1 – 6) for the preset
station you want.
3
Press and hold the number button (in
this example, 1) for more than 2
seconds.
“P1” flashes for a while.
4
Repeat the above procedure to store
other stations into other preset
numbers.
Notes:
• A previously preset station is erased when a new
station is stored in the same preset number.
• Preset stations are erased when the power supply
to the memory circuit is interrupted (for example,
during battery replacement). If this occurs, preset
10
the stations again.
If the sound quality decreases and the
stereo effect is lost while listening to
an FM station
In some areas, adjacent stations may interfere
with each other. If this interference occurs, this
unit can automatically reduce this interference
noise (the initial setting when shipped from the
factory). However, in this case, the sound
quality will be degraded and the stereo effect
will be also lost.
If you do not want to degrade the sound quality
and to lose the stereo effect, rather than to
eliminate the interference noise, see “To
change the FM tuner selectivity – IF FILTER”
on page 20.
When using this until in an area other than
North or South America:
You need to change the AM/FM channel
intervals. See “To change the AM/FM channel
intervals – AREA” on page 20.
Loading...